advertisement
PT1700MX / PT1785P
Touch Screen Monitor
USER’S GUIDE
www.planar.com
The information contained in this document is subject to change without notice.
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced, translated to another lan- guage or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission.
Windows is a registered trademark of Microsoft, Inc.
Other brand or product names are trademarks of their respective holders.
For more information on how to recycle your product, please visit
WWW.PLANAR.COM/GREEN.
Table of Contents
Usage Notice ........................................................................... 3
Precautions ..................................................................................................... 3
Introduction ............................................................................. 4
About PT1700MX / PT1785P.......................................................................... 4
Touch Screen for PT1700MX ........................................................................ 5
Touch Screen for PT1785P ........................................................................... 5
Package Overview .......................................................................................... 6
Installation ............................................................................... 7
Product Overview ............................................................................................ 7
Front View.................................................................................................. 7
PT1700MX Bottom View ........................................................................... 7
PT1785P Bottom View .............................................................................. 7
Start Your Installation ...................................................................................... 8
Connecting the Display (Figure 11.1) ........................................................... 10
(Figure 11.1) .......................................................................................... 11
Kensington Security Slot ............................................................................... 12
VESA Mount your monitor ............................................................................ 13
1
User Controls ........................................................................ 15
Side Panel Controls ...................................................................................... 15
How to Use the OSD Menus ......................................................................... 16
On-Screen Display Menus ......................................................................... 18
Appendix ................................................................................ 19
Troubleshooting ............................................................................................ 19
Warning Signal .............................................................................................. 20
Product Dimensions ...................................................................................... 21
Compatibility Modes ...................................................................................... 23
Touch Screen Driver Installation ................................................................... 24
Technical Support ......................................................................................... 31
2
Usage Notice
Warning
- To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture.
3
Warning
- Please do not open or disassemble the product as this may cause electric shock.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit.
Do:
Turn off the product before cleaning.
Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50/50 mixture of water and isopropyl alcohol.
Use a soft cloth moistened with mild detergent to clean the display housing.
Use only high quality and safety approved AC/DC adapter.
Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time.
Don’t:
Do not touch the LCD Display screen surface with sharp or hard objects.
Do not use abrasive cleaners, waxes or solvents for your cleaning.
Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
Introduction
About PT1700MX / PT1785P
The PT1700MX / PT1785P is a 17” flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD).
This unit is to be used as commercial and light industrial equipment only.
Features include:
Direct Analog signal input
Active matrix TFT LCD technology
1280x1024 SXGA resolution
17” viewable display area
31.47 ~ 80 kHz horizontal scan
56 ~ 75 Hz high refresh rate
0.264mm x 0.264mm Pixel pitch
Auto adjustment function
Multilingual OSD user controls
VESA DPMS power saving
Kensington security slot
75 mm / 100 mm VESA mount
Removable base for flexible mounting solutions.
PT1700MX – 5-wire resistive touch screen with dual RS-232 Serial/USB controller
PT1785P – Projected capacitive touch screen with USB controller
5-wire resistive touch screen with dual RS-232 Serial/USB
controller
Built-in speakers-1W X 2
4
Touch Screen for PT1700MX
5-wire resistive touch screen for finger and stylus input
Surface: Anti-glare treatment
Interface: Dual RS-232 Serial/USB controller
Durability: 35 million touches at a single point
Hardness of surface: 3H Typical
Operating force: 40g~200g when using a silicon rubber tipped pen with a
1 mm diameter minimum and a hardness of 60 degree.
Transmittance: 82%±5%
Driver: Windows
®
7/8, VISTA, XP, 2000, ME, 98, NT4.0, CE,
XP Embedded, Linux kernel 2.6.x (32 bit & 64 bit), Apple
®
Mac OS
Touch Screen for PT1785P
Project capacitive touch screen for finger input only
Surface: Glare treatment
Interface: USB controller
Transmittance: 90%±5%
Driver: Windows
®
7/8, VISTA 64/32 bits, XP, 2000,
XP Embedded Express, Linux, Apple
®
Mac OS
5
Package Overview
LCD Display Power Cord VGA Signal Cable
USB Cable (A to B) Audio-in Cable
RS-232 Cable
(PT1700MX only)
Landing Strip DC Power Supply
(sold separately)
User’s Guide
Cable Cover Cable Cover Screw
6
Installation
Product Overview
► Front View
7
PT1700MX PT1785P
► PT1700MX Bottom View (Without Stand)
► PT1785P Bottom View (Without Stand)
Start Your Installation
1. Lay the
display
flat on an even surface.
2. Remove the stand back cover by pulling in the direction of the arrow as seen in step 2 diagram.
3. Move the stand into position as seen in step 3 diagram.
4. Connect the cables to the appropriate connectors as seen in Step 4 diagram.
Use step 4-1 diagram if using the RS-232 serial connector. Use step 4-2 diagram if using the USB connector.
8
5. Take the optional cable cover and screw from the accessory box. Position all cables under the cover lip as seen in the step 5 diagram.
6. Using a Philips Head screwdriver, insert the screw (CBM M3x6) into the cable
9 cover and monitor as seen in the step 6 diagram.
7. Re-attach the stand back cover to the stand by pressing firmly until the tabs snap into place as seen in the step 7 diagram. You may also keep the cables in order by using the cable organizer.
Connecting the Display (Figure 11.1)
To setup this display, please refer to the following figure and procedures.
1. Be sure all equipment is turned off.
2. Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet (11.1).
3. Connect the D-SUB cable from the display’s VGA input connector to the
D-SUB connector of your host computer and tighten the screws (11.1).
4. Connect the Audio-In cable from the audio input port of your display to the Audio-out port of your computer (11.1).
5. Connect the RS-232 or USB cable from the RS-232 or USB port of your display to the RS-232 port or USB port (11.1) of your computer.
6. Configure the touch screen. Refer to the “Touch Screen Driver
Installation” section on page 24.
7. Once the touch screen is configured, the monitor is ready for use.
10
To ensure the display works well with your computer, please configure the display mode of your graphics card to make it less than or equal to
1280 x 1024 resolution and make sure the timing of the display mode is compatible with the LCD display.
We have listed the compatible “Video Modes” of your display in the appendix for your reference.
(Figure 11.1)
► PT1700MX
11
► PT1785P
Kensington Security Slot
The monitor can be secured to your desk or any other fixed object with
Kensington lock security products. The Kensington lock is not included.
12
VESA Mount Your Monitor
This monitor conforms to the VESA Flat Panel Mounting Physical Mounting
Interface standard which defines a physical mounting interface for flat panel monitors, and corresponding with the standards of flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor.
To mount the monitor on a UL certified swing arm or other mounting fixture, follow the instructions included with the mounting fixture to be used.
13
Warning!
Please select the proper screws!
The distance between the back cover surface and the bottom of the screw hole is 8 mm. Please use four M4 screws diameter with proper length to mount your monitor.
Please note: the mounting stand must be able to support at least 13.2 lbs(6Kg).
Remove the Deskstand
1. Remove stand back cover.
14
2. Remove hinge cover
3. Remove 4 screws and then remove hinge.
User Controls
Side Panel Controls
15
Key
OSD
Menu off status
Menu appear
Brightness
Mute
Menu on status
Menu disappear / return to main item
Main item select up / Adjust up
Main item select down / Adjust down
Enter / Select sub-item function
Power On / Off
How to Use the OSD Menus
1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menu.
2. Choose the adjustment items by pressing the “Enter ” button.
3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button.
4. With the OSD menu on screen, press “ Menu” button to return main menu or exit OSD.
5. The OSD menu will automatically close, if you have left it idle for a pre-set time.
6. To Lock the OSD / Power menu buttons, please follow the instructions below.
(Please note: the monitor has to be turned ON with a valid signal pre-set)
(a.) Press “Menu” key , the OSD menu will pops upon display.
(b.) Press and hold the “Menu” key again with the OSD menu on the screen, the OSD menu will disappear. Then press the “Power” key 1 time while the menu key is still being pressed. The “Lock/Unlock” menu will appear for 3 seconds.
(c.) Use the “Enter” key to select OSD or Power setting then set at
“Lock” by pushing the “UP” or “Down” button.
(d.) When the “UP” or “Down” button is released, the previous setting will be saved and exit the “Lock/Unlock” menu automatically.
7. To Unlock the OSD / Power menu buttons, please follow the instructions below.
(Please note: the monitor has to be turned ON with a valid signal pre-set)
(a.) Press and hold the “Menu” key then press the “Power” key simultaneously, the “Lock/Unlock” menu will appear for 3 seconds.
(b.) Use the “Enter” key to select OSD or Power setting then set at
“Unlock” by pushing the “UP” or “Down” button.
16
(c.) When the “UP” or “Down” button is released, the previous setting will be saved and exit the “Lock/Unlock” menu automatically.
Please note: a. When the OSD Lock function is selected, this indicates that all the buttons except “power” button are now disabled. b. When the Power Lock function is selected, this indicates that the power key is disabled; user can not to turn off the monitor by
“Power” key.
17
On-Screen Display Menus
Main OSD Menu:
ITEM
Contrast
Brightness
Auto Adjust
CONTENT
The monitor luminance level control.
The monitor backlight level control.
Fine-tune the image to full screen automatically.
Left/Right Moving screen image horizontal position to left or right.
18
Up/Down Moving screen image vertical position to up or down.
Horizontal size
Fine
OSD Left/Right
OSD Up/Down
OSD Time out
OSD Language
Factory Reset
RGB
Volume
Mute
The screen image horizontal dot clock adjustment.
The screen image pixel phase adjustment.
Moving OSD menu horizontal position to left or right.
Moving OSD menu vertical position to up or down.
OSD auto-disappear time selection.
OSD menu language selection. ( English, French,
Japanese, Deutsch, Spanish, Italian, Traditional Chinese and Simplified Chinese)
Factory default value restored.
Color temperature selection. (9300K, 6500K, 5500K,
7500K, User)
Audio volume adjustment.
Audio On/Off control.
Appendix
Troubleshooting
If you are experiencing trouble with the display, refer to the following. If the problem persists, please contact your local dealer or our service center.
Problem: No image appears on screen.
Check that all the I/O and power connectors are correctly and well connected as described in the “Installation” section.
Make sure the pins of the connectors are not crooked or broken.
Problem: Partial Image or incorrectly displayed image.
Check to see if the resolution of your computer is higher than that of the display.
Reconfigure the resolution of your computer to make it less than or equal to 1280 x 1024.
Problem: Image has vertical flickering line bars.
Use "Fine" to make an adjustment.
Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the display.
Problem: Image is unstable and flickering
Use "Horizontal size" to make an adjustment.
Problem: Image is scrolling
Check and make sure the VGA signal cable (or adapter) is securely connected.
Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the display.
Problem: Vague image (characters and graphics)
Use "Fine" to make an adjustment. If this problem still exists, use
"Horizontal size" to make an adjustment.
19
Warning Signal
If you see warning messages on your screen, this means that the display cannot receive a clean signal from the computer graphics card.
Below are the three kinds of Warning Signal. Please check the cable connections or contact your local dealer or our service center for more information.
No Signal
This message means that the display has been powered on but it cannot receive any signal from the computer graphics card. Check all the power switches, power cables, and VGA signal cable.
Going to Sleep
The display is under the power saving mode. In addition, the display will enter power saving mode when experiencing a sudden signal disconnecting problem.
The monitor can be activated by pressing any keyboard, triggering the mouse or touching the screen.
Out of Range
This message means that the signal of the computer graphic card is not compatible with the display. When the signal is not included in the "Video
Modes" list we have listed in the Appendices of this manual, the monitor will display this message.
20
Product Dimensions
PT1700MX
21
PT1785P
22
Compatibility Modes
Mode
IBM VGA
IBM VGA
VESA VGA
VESA VGA
VESA SVGA
VESA SVGA
VESA SVGA
VESA SVGA
VESA XGA
VESA XGA
VESA XGA
VESA SXGA
VESA SXGA
VESA SXGA
VESA SXGA
Apple Mac II
Apple Mac
Resolution
720x400
640x480
640x480
640X480
800x600
800x600
800x600
800x600
1024x768
1024x768
1024x768
1280x1024
1280x1024
1280x960
1152x864
640x480
832x624
H-Frequency
(KHz)
31.47
31.47
37.86
37.50
35.16
37.88
48.08
46.88
48.36
56.48
60.02
64.00
80.00
60.00
67.50
35.00
49.72
V-Frequency
(Hz)
70
60
72
75
56
60
72
75
60
70
75
60
75
60
75
66
75
23
Touch Screen Driver Installation
The PT1700MX is available with both RS232 and USB connections. The touch driver is located at www.planar.com/support for these operating systems:
Windows
®
7/8, VISTA, XP, 2000, ME, 98, NT4.0, CE, XP Embedded,
Linux kernel 2.6.x (32 bit & 64 bit), Apple
®
Mac OS.
The PT1785P is available with USB connection. The touch driver is located at www.planar.com/support for these operating systems: Windows
®
7/8, VISTA
64/32 bits, XP, 2000, XP Embedded (
Express only), Linux, Apple ®
Mac OS.
Please Note:
1. The PT1700MX is Microsoft ® Windows® HID (Human Interface Device) compatible if you use the USB touch screen interface. No additional software driver is required for general operation of the touch screen. A calibration tool can be installed for improved touch position accuracy.
See “Optional Calibration Tool Install”section for more information.
2. For PT1785P, the system requires 15 seconds for Windows 7/8 to
Install/uninstall the touch driver while turning power on/off or plugging/unplugging USB cable.
24
PT1700MX Optional Calibration Tool Install:
If you would like to use the Optional Calibration Tool, follow the instructions below. Please note: the calibration tool supports Windows
®
7/8, VISTA, XP and XP Embedded operating systems via USB only.
1.
Visit www.planar.com/support .
18
2. Select the monitor size and then model name.
3. Click on the “Load Utility” button that appears to the right of the model name.
4. The HID calibration tool will automatically open. From here the user can choose to do the following: a. 4 Points Calibration b. 9 Points Linearization c. 25 Points Linearization d. Clear e. Draw Test f. Advanced. In the Advanced settings area the user may do the following: i. Adjust the Double Click Area. ii. Enable auto right click and adjust the auto right click time. iii. Choose to be either in the HID Mouse Mode or HID Digitizer Mode
(Windows
®
Vista and Windows
®
7 and Windows
®
8). iv. Simply click the “Apply” button once the settings are finalized.
25
PT1785P Calibration Instructions:
Calibrating the touch screen in Windows 7/8:
1. Tap the Start button, Control Panel and then Hardware and Sound.
2. Under Tablet PC Settings, tap Calibrate the screen for pen or touch input.
3. On the Display tab, under Display options, tap Calibrate and then Yes to allow the program to make changes.
4. Follow the on-screen instructions to calibrate the touch screen.
26
27
PT1700MX / PT1785P Driver Install Instructions:
If you are using a PC running Windows
®
7/8, VISTA, XP, 2000, ME, 98,
NT4.0, follow the instructions below:
1. Power on the PC.
2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the
LCD display.
3. Visit www.planar.com/support .
4. Follow the step-by-step instructions as shown on the pop-up windows.
If you are using a PC running driver Linux kernel 2.6.x (32 bit & 64 bit), follow the instructions below:
1. Power on the PC.
2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the
LCD display.
3. Visit www.planar.com/support .
4. Follow the step-by-step instructions as shown on the pop-up windows.
If you are using a PC running Windows
®
XP Embedded, follow the instructions below:
Express:
1. Power on the computer.
2. Make sure that the RS232 or USB cable is connected to the computer.
3. Be sure that your EWF is disabled. If your EWF is enabled, please disable the EWF by using the EWF Manager command.
4. Once the EWF is disabled click on the XP driver at www.planar.com/support and follow the step-by-step instructions as shown on the pop-up windows.
28
Custom (PT1785P excluded):
1. Power on the computer.
2. Make sure that the RS232 or USB cable is connected to the computer.
3. Follow the step-by-step instructions found in the zipped file at www.planar.com/support .
If you are using a PC running Windows
®
CE, follow the instructions below:
1. Power on the computer.
2. Make sure that the RS232 or USB cable is connected to the computer.
3. Using Platform Builder, build an image file by following the step-by-step instructions found in the zipped file at www.planar.com/support .
If you are using a PC running Linux or Apple
®
Mac OS, follow the instructions below:
1. Power on the computer.
2. Make sure that the RS232 or USB cable is connected to the computer.
3. Follow the step-by-step instructions found in the zipped file at www.planar.com/support .
When changing the Touch Interface (RS-232 or USB), please follow instructions below.
1. Uninstall the touch driver.
2. Re-start the computer.
3. Remove the original Touch Interface (RS-232 or USB).
4. Connect the computer to the Touch Interface (RS-232 or USB) that you would like to use.
5. Visit www.planar.com/support , then follow the step-by-step instructions as show on monitor.
29
PLEASE NOTE!
Don’t plug in both the RS-232 and USB cables!
Doing so may cause a driver conflict, making your touch screen inoperable.
30
Technical Support
Cables and Accessories
To find cables and accessories for your Planar monitor, touch screen or other
Planar products visit our online store at www.PlanarOnline.com.
Technical Support
Visit Planar at http://www.planar.com/support for operations manuals touch screen drivers, warranty information and access to Planar’s Technical
Library for online troubleshooting.
To speak with Planar Customer Support please have you model and serial number available and dial:
Planar Support
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US.
Hours: 24 hours a day, 7 days a week.
Toll or long distance charges may apply.
31
Planar Systems, Inc.
Customer Service
24x7 Online Technical Support: http://www.planar.com/support
1195 NW Compton Drive
Beaverton, OR 97006-1992
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States.
Hours: 24 hours a day, 7 days a week
32
© 2014 Planar Systems, Inc. 4/14 Planar is a registered trademark of Planar Systems, Inc.
Other brands and names are the property of their respective owners.
Technical information in this document is subject to change without notice.
020-0698-00 Rev I
820470025106
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement