PK-543A 5-4-3 WIRE APARTMENT INTERCOM AMP WIRING INSTRUCTIONS Innovations in Communications

PK-543A 5-4-3 WIRE APARTMENT INTERCOM AMP WIRING INSTRUCTIONS Innovations in Communications
Innovations in Communications
since 1955
PK-543A
5-4-3 WIRE APARTMENT INTERCOM AMP
WIRING INSTRUCTIONS
Figure A
APPLICATION
TM
Suite Stations:
To Additional
Suites
Add Risers
as Required
○
○
○
○
○
Entry
Door
Opener
1. Read installation instructions to determine equipment
location and installation methods.
2. Install housings (or back boxes) and wiring.
3. Check wiring, connect and install equipment.
4. Apply power and check operation.
EQUIPMENT LOCATION
Suite/Apartment Stations
Locate suite stations (also known as remote stations)
where convenient for use. See Figure A (page1) for riser
diagram, or Figure 1 (page 4) for wiring/hook-up
diagram.
Entrance/Lobby Panel
Locate the entrance panel where it is sheltered from
weather. If it must be mounted outdoors, consider wind
direction and optional Rain-Guard weather hood.
PK-543A Amplifier
Install amplifier inside the entrance panel if space
permits. If necessary to install the amplifier elsewhere
due to temperature extremes (operating temperature
range is 0–30°C) or because the panel is not large
enough to house the amplifier, then use a 2 conductor
shielded cable for the entrance panel speaker (connect
shield drain to amplifier terminal G). Refer to
Connections Section, Item #3 for further details.
800-231-1414 • 631-231-1414
155 Adams Avenue • Hauppauge, NY 11788-3699
Fax 631-231-1498 • www.LEEDAN.com
All Rights Reserve
1 twisted pair #22, plus 2
cond. #22, plus 1 cond. #22
per suite in riser
Panel
2 cond #18
PROCEDURE
©2010 LEE DAN® Communications, Inc.
For 5-wire stations:
○
Optional equipment is available to provide additional
functions such as post office (USPS) key door release,
additional entrance panels, strobe light call indication
(LI-404B) and auxiliary relay (RY-014B) for ancillary
device operation (bells, lights, etc.).
1 twisted pr #22, plus 1 cond.
#22 gauge per suite in riser
or,
1 twisted pr #22, plus 1 cond.
#22 common, plus 1 cond. #22
gauge per suite in riser
or,
○
○
For 3-wire stations:
For 4-wire stations:
○
ENTERCOM Apartment Entry Intercoms provide twoway communications between the building entrance and
each suite/apartment. Hands-free loudspeaker operation at
the entrance panel and push button controlled
communication at the suite locations provide for easy
operation. Controlled door entry is permitted by push button
operation at the suite in conjunction with electric door
release.
120 VAC
Transformer
WIRING
Suite/Apartment Stations
Stations may be connected in risers using the cable
configurations shown in Figure A, above.
The maximum cable length is 400 feet (120 meters).
Additional risers may be added as needed. Station
cables must not be run in the same conduit with (or
too close to) electrical wiring or background music,
and must not be close to fluorescent lights, dimmers or
other electrical equipment. Failing to observe this
requirement can result in noise entering the intercom
audio. Ensure that sufficient amounts of cable are left
in the back box to make connections to stations. Do
not cut cable at each station.
Transformer
Cable wiring must be 2 conductor #18 AWG with a
maximum cable length of 80 feet (25 meters). If using
#14 AWG wire, this distance can be extended to 200
feet (60 meters). Route cable away from suite station
wiring and maintain a minimum of 3 feet (1 meter) of
clearance between the transformer and the amplifier.
INTERCOMS • MAILBOXES • DIRECTORIES
ANNUNCIATORS • WIRE & CABLE • NURSE-CALL
With continuous product improvement, specifications are subject to change without notice.
IN-826 (3/10)
Door Release
Cable wiring must be 2 conductor #18 AWG with a
maximum length of 50 feet (15 meters). See Figure
2—PK-543A 'Door Strike Applications' for specifics of
each door control unit configuration. Note: A PS-30A
transformer must be used for 24 VAC door strike and
12 VDC Maglock applications (8 volt tap required).
CONNECTIONS
Before connecting to unit and applying power, verify that
wires are free from shorts and grounds. Make connections
as per Figure 1—PK-543A Wiring Diagram. Observe the
following notes:
1. Do not apply power to the transformer primary until the
entire system has been installed and checked for shorts
and grounds. The common wires connecting to terminals
1, 2, 3, E and 5 must show open circuit when tested with
an ohmmeter.
2. Use twisted pair wiring as shown. Do not interchange
wires or reverse polarity!
3. Install PK-543A amplifier inside the entrance panel if
space permits. If it is necessary to install the amplifier
elsewhere due to temperature extremes (operating
temperature range is 0–30°C) or because the entrance
panel is not large enough to house the amplifier, then
use a 2 conductor shielded cable for the entrance panel
speaker (connect shield drain to amplifier terminal G).
4. The amplifier must be located at least 3 feet (1 meter)
from the transformer or other electrical devices.
5. Do not run wiring for station common wires and
entrance panel speaker in the same cable and/or
conduit. This will cause feedback on the system.
6. Door release wiring should be run separate from
entrance panel speaker wiring.
Medium Door Time Set SW1 to OFF (left) and SW2 to
ON (right), 10 seconds.
Long Door Time
Set SW1 to OFF (left) and SW2 to
OFF (left), 25 seconds.
Entrance Tone
Set SW3 to ON (right) to activate this
feature—must use warble tone.
Postal Timer
Set SW4 to ON (right) and SW5 to
OFF (left) to make postal control
timer independent at 25 seconds
PK-543 Compatible Set SW4 to OFF (left) and SW5 to
ON (right) for PK-543 (old style)
drop-in replacement*.
Door Hold Time Out Set SW6 to OFF (left) to activate this
feature.
Talk Interlock
Set SW7 to OFF (left) to activate this
feature (available for 4-wire stations
only).
* For PK-543 (old style) Compatible mode, set SW4
OFF, SW5 ON, SW6 ON & SW7 ON. Also remove JP5
shunt, set J2 to shunt 1–2 and set J1 shunt to 2–3.
The Entrance Tone setting, when active, will generate a user
feedback tone at the entrance panel when visitors press call
buttons. If the warble tone is in use and the entrance tone
feature is active, the tone will also be heard through the
entrance panel speaker when the call button is pressed.
The Door Hold Time Out setting, when active, will allow
the door control device (door strike, maglock, etc.) to time
out normally, despite the DOOR button being held at the suite.
SAFETY TIP: The Talk Interlock setting, when active, will
require that the TALK button (at the suite) is pressed before
the DOOR button will activate the door control device.
OPTIONAL ACCESSORIES
SHUNT AND DIPSWITCH SETTINGS
Set the dipswitches on the PK-543A as per application
requirements. See also Figure 3—PK-543A 'Shunts and
Settings'. The selectable features and controls are as follows:
Install optional accessories according to the instructions
provided.
Finish & TEST Installation
1. Confirm that all equipment is properly installed.
Shunt JP5 Install for maglock applications. Maximum
current for maglock is 500 mA at 12 VDC, or
250 mA at 24 VDC.
2. Connect power to transformer primary (120 VAC),
and ensure that local electrical codes have been
complied with.
Shunt J2
Place shunt across: 1–2 for door strike
applications; 2–3 for maglock applications.
3. At the entrance panel, push each button and verify that
the correct suite is called.
Shunt J1
Place shunt across: 1–2 for +12 VDC
maglock; 2–3 for +24 VDC maglock or
AC/DC door strike applications.
4. At each suite, push the TALK and LISTEN buttons to
communicate with a person at the entrance panel. Then
push the DOOR button to confirm that the door release
operates correctly.
Short Door Time
Set SW1 to ON (right) and SW2 to
OFF (left), 2 seconds
Page 2 • IN-826 PK-543A Installation Instructions
Copyright © Lee Dan Communications, Inc. All Rights Reserved.
ADJUSTMENTS
Voice Volume and Tone Volume can be adjusted on the
amplifier, via the access hole, with a small screwdriver.
TROUBLESHOOTING
(refer to theory drawing for additional information)
Entire System Dead
If power LED is not illuminated, check for 16 VAC at
transformer secondary and 120 VAC at transformer
primary. If LED is illuminated, review field wiring and
perform direct test using one of the apartment stations
to eliminate field wiring.
No Talk
Check wiring to terminals 1 and 2, and check whether
wiring to entrance panel speaker is shorted or open. Suite
station can be swap tested with another working unit.
No Listen
Check wiring to terminals 1 and 3, or for short between
terminals 1 and 2. Check to see if wiring to entrance
panel speaker is shorted or open. Suite station can be
swap tested with another working unit.
No Door Operation
Check wiring to door release for shorts and opens, or
for defective door release. Confirm that shunts are
properly set for door release type and that connections
to appropriate output have been made. Check wiring to
terminals 2 and 3, or 1 and E (depending upon suite
station type).
No Call Tone
Check wiring to terminal Z or ZW to entrance panel,
related entrance panel call buttons, and suite station X
terminal. Suite station can be swap tested with another
working unit.
Excessive Hum or Distortion
Check whether wiring is installed too close to electrical
wiring or electrical devices; amplifier installed too close
to transformers or other electrical devices; twisted pair
wiring not used as required; or amplifier voice volume
set too high.
Radio Interference
Connect G terminal from amplifier to electrical ground.
Note: This connection is not shown on the wiring
diagram, since the situation is not always improved by
adding it. If the problem persists, consult the factory or
service representative.
Oscillation (feedback or howling)
Reduce the voice volume until oscillation is eliminated.
If oscillation stops when the call tone wire is removed
from ZW, set entrance tone (SW3) to the OFF (left)
position.
Copyright © Lee Dan Communications,, Inc. All Rights Reserved.
SIGNAL FLOW AND THEORY OF
OPERATION FOR PK-543A AMPLIFIER
AND APARTMENT INTERCOM SYSTEM
The following example describes an apartment intercom
system using a PK-543A in conjunction with a 4-wire suite
station. Refer also to Figure 4—PK-543A Theory Diagram.
Call Button
Pressing a suite station call button on the entrance panel
routes the call tone from the Z or ZW terminal on the
PK-543A to the X terminal (tone in) on the associated
suite station. This signal then passes through the speaker
and returns to the PK-543A via the 1 terminal (audio
common). If the warble tone is in use and the entrance
tone feature is active, the tone will also be heard through
the entrance panel speaker when the call button is
pressed.
Talk Button
Pressing the TALK button at a suite station connects the
suite station’s internal speaker to terminals 1 and 2 of
the PK-543A, which serves as an audio input to the
amplifier. The audio is then amplified and sent to
terminals A and G, which are connected to the entrance
panel’s speaker (speaker mode).
Listen Button
Pressing the LISTEN button at a suite station connects the
suite station’s internal speaker to terminals 1 and 3 of
the PK-543A, which serves as an audio output from the
amplifier. This allows the suite station to receive the
amplified audio being received by the amplifier on
terminals A and G from the entrance panel speaker
(microphone mode).
Door Button
Pressing the DOOR button at a suite station creates a
closure between terminals 2 and 3 on the PK-543A. This
state is sensed by the amplifier and causes the door
release to be activated (output specifics are based on
PK-543A settings). This state is also triggered by shorting
terminals 1 and E as is typically done by a postal lock.
Cross Reference Part Index
Model Numbers Below Are Interchangeable:
PK543 = PK-543 (Old Style)
PK-543 = PK543 (Old Style)
PK543A = PK-543A (New Style)
PK-543A = PK543A (New Style)
PS-3A, PS-3B = SS102A (16VAC)
PS-30A = SS106 (16VAC)
RY014B = RY-014B
RY-014B = RY014B
SS102A = PS-3A, PS-3B
SS106 = PS-30A (Tri-Volt: 8/16/24VAC)
IN-826 PK-543A Installation Instructions • Page 3
Page 4 • IN-826 PK-543A Installation Instructions
Copyright © Lee Dan Communications, Inc. All Rights Reserved.
(Optional)
5
Tone in
X
1
Twisted Pair
Tone in
X
3
2
1
Twisted Pair
X
Tone in
E
(Typical)
5 Wire
Intercom
Station
3
2
1
Twisted Pair
DO NOT run these wires
in the same cable! It will
cause feedback.
16 VAC
LL+
D
K
C
P
G
A
E
5
3
2
1
ZW
Z
CONNECT TO
120 VAC
(-) DC Door power
(+) DC Door power
Switched AC door release
AC Input (Common)
AC Input
Strobe (LI404) power (+24VDC)
Entry speaker common
Entry speaker switched audio
5 Wire station door release
3 wire station audio
Audio to station
Audio from station
Audio Common
Warble tone out
Tone out
PK543A Amplifier
16V AC Doorstrike Configuration
Remove shunt on JP5, set J1
shunt to 2 and 3 and J2 shunt
to 1 and 2. (see other diagrams
for additional configurations)
PS-3A, PS-3B
TRANSFORMER
YEL
YEL/BLK
BRN
RED
ORG
WHT/BLK
ORG/BLK
BLK
WHT
GRN
GRY
VIO
BLU
RED/WHT
BRN/WHT
#18 AWG Wire
If shielded wire is used, connect
shields to orange/black wire (G)
at amplifier.
Drawing Name & Number: IL826 PK543A Wiring Rev1 052504 1
Post Office Lock
Adapter
Apartment Call Buttons
(Typical)
ENTRY PANEL
Twisted Pair
Notes:
1. Use #22 AWG wire unless shown otherwise.
2. Warble or Steady Tone is hard wire selectable.
3. If entry panel has handset, connect it in place of speaker.
4. 3, 4 and 5 wire intercom station types may be used in any combination,
with the exception of the IR102C, which can only be used in conjunction
with other IR102B or C devices.
5. Door release wiring should be run separate from entrance panel speaker wiring.
6. Shunts referred to in diagrams are located on PK543A.
7. Terminal P is for strobe only, do NOT connect other wires to this terminal.
Switched Audio
(Typical)
Audio to station
(Typical)
Audio Common
4 Wire
Intercom
Station
Audio from station
3 Wire
Intercom
Station
5 Wire sta. door release
See note #4
Audio to station
Blue Wire to 1
Violet Wire to 2
Gray Wire to 3
White -- X (call wire)
Audio from station
IR402 Connections
Audio Common
Figure 1 - PK-543A Wiring Diagram
Audio Common
Figure 2 - PK-543A Doorstrike Applications
+24V AC Doorstrike Application:
Remove JP5 Shunt
Set J1 shunt to 2 and 3
Set J2 shunt to 1 and 2
#18 AWG Wire
Doorstrike
#18 AWG Wire
Doorstrike
PK-543A Amplifier
LL+
D
K
C
P
G
A
E
5
3
2
1
ZW
Z
YEL
YEL/BLK
BRN
RED
ORG
WHT/BLK
ORG/BLK
BLK
WHT
GRN
GRY
VIO
BLU
RED/WHT
BRN/WHT
16V DC Doorstrike Application:
Remove JP5 Shunt
Set J1 shunt to 2 and 3
Set J2 shunt to 1 and 2
PK-543A Amplifier
LL+
D
K
C
P
G
A
E
5
3
2
1
ZW
Z
(-) DC Door power
(+) DC Door power
Switched AC door release
AC Input (Common)
AC Input
Strobe (LI404) power (+24VDC)
Entry speaker common
Entry speaker switched audio
5 Wire station door release
3 wire station audio
Audio to station
Audio from station
Audio Common
Warble tone out
Tone out
YEL
YEL/BLK
BRN
RED
ORG
WHT/BLK
ORG/BLK
BLK
WHT
GRN
GRY
VIO
BLU
RED/WHT
BRN/WHT
(-) DC Door power
(+) DC Door power
Switched AC door release
AC Input (Common)
AC Input
Strobe (LI404) power (+24VDC)
Entry speaker common
Entry speaker switched audio
5 Wire station door release
3 wire station audio
Audio to station
Audio from station
Audio Common
Warble tone out
Tone out
16 VAC Tap
CONNECT TO
120 VAC
Common
8 VAC Tap
CONNECT TO
120 VAC
16 VAC
PS-3A, PS-3B
TRANSFORMER
PS-3A, PS-3B
TRANSFORMER
#18 AWG Wire
#18 AWG Wire
Drawing Name & Number: IN-826 PK543A Doorstrike Applications 1 Rev0 050604 1
Maglock
+12VDC/500mA DC Maglock Application:
Install JP5 Shunt
Set J1 shunt to 1 and 2
Set J2 shunt to 2 and 3
#18 AWG Wire
LP
8
4 pin header JP3,
located in front of
main connector.
YEL
YEL/BLK
BRN
RED
ORG
WHT/BLK
ORG/BLK
BLK
WHT
GRN
GRY
VIO
BLU
RED/WHT
BRN/WHT
#18 AWG Wire
Maglock
PK543A Amplifier
LL+
D
K
C
P
G
A
E
5
3
2
1
ZW
Z
+24VDC/250mA DC Maglock Application:
Install JP5 Shunt
Set J1 shunt to 2 and 3
Set J2 shunt to 2 and 3
(-) DC Door power
(+) DC Door power
Switched AC door release
AC Input (Common)
AC Input
Strobe (LI404) power (+24VDC)
Entry speaker common
Entry speaker switched audio
5 Wire station door release
3 wire station audio
Audio to station
Audio from station
Audio Common
Warble tone out
Tone out
PK543A Amplifier
LL+
D
K
C
P
G
A
E
5
3
2
1
ZW
Z
YEL
YEL/BLK
BRN
RED
ORG
WHT/BLK
ORG/BLK
BLK
WHT
GRN
GRY
VIO
BLU
RED/WHT
BRN/WHT
(-) DC Door power
(+) DC Door power
Switched AC door release
AC Input (Common)
AC Input
Strobe (LI404) power (+24VDC)
Entry speaker common
Entry speaker switched audio
5 Wire station door release
3 wire station audio
Audio to station
Audio from station
Audio Common
Warble tone out
Tone out
16 VAC Tap
Common
CONNECT TO
120 VAC
CONNECT TO
120 VAC
16 VAC
8 VAC Tap
PS-30A
TRANSFORMER
#18 AWG Wire
PS-3A, PS-3B
TRANSFORMER
#18 AWG Wire
Note: LP and 8 are each available on two
pins of the JP3 connector. Brackets are
provided to identify.
Drawing Name & Number: IN-826 PK543A Doorstrike Applications 2 Rev1 051606 1
Copyright © Lee Dan Communications,, Inc. All Rights Reserved.
IN-826 PK-543A Installation Instructions • Page 5
Figure 3 - PK-543A Shunts and Settings
CONNECTORS
LP
8
D
K
C
A
ZW
Z
JP5
PK-543A POWER PACK
4 Wire
Intercom
Station
Main Connector
PK502B Interface Connector
1 AND 2 OFF = LONG
DOOR TIME
TONE
VOLUME
SPEAKER
P.O. LOCK (4)
COMMON
WIRES
BUZZ 1
BUZZ 2
X
3
2
1
VOICE
VOLUME
TRANSFORMER
+24V
Audio Common
AC DOOR
(Typical)
Audio from station
DC DOOR
Audio to station
LP & 8 Connector
1 2 3 1-2 +12V DC OUT
2-3 +24V DC OUT
Tone in
J1
LL+
D
K
C
P
G
A
E
5
3
2
1
ZW
Z
J1
Dipswitch Settings:
Short Door Time
Medium Door Time
Long Door Time
Entrance Tone
Postal Timer
PK543 Compatible
Door Hold Time Out
Talk Interlock
PK543A POWER PACK
LED = POWER
JP5
1 2 3 1-2 DOOR STRIKE
2-3 MAGLOCK
J2
Power LED
Dipswitch
®
LEE DAN®
WARNING
VERIFY ALL CONNECTIONS
BEFORE ATTACHING
TRANSFORMER
J2
SEE MANUAL FOR DETAILS
SWITCH FUNCTIONS
1 SHORT DOOR TIME
2 MEDIUM DOOR TIME
3 ENTRANCE TONE
4 POSTAL TIMER
5 PK543 COMPATIBLE
6 DOOR HOLD TIMEOUT
7 TALK INTERLOCK
For PK543 drop-in replacement set:
SW4 OFF, SW5 ON, SW6 ON & SW7 ON
Shunts: JP5 remove, J2 1-2 & J1 2-3
RY014B
1 B
A
C X
(right and left are referenced from the view above)
- set SW1 to ON (right) and SW2 to OFF (left), 2 seconds
- set SW1 to OFF (left) and SW2 to ON (right), 10 seconds
- set SW1 to OFF (left) and SW2 to OFF (left), 25 seconds
- set SW3 to ON (right) to activate this feature
- set SW4 to ON (right) and SW5 to OFF (left) to make postal control timer independent at 25 seconds
- set SW4 to OFF (left) and SW5 to ON (right) to make unit for drop-in replacement for PK543*
- set SW6 to OFF (left) to activate this feature
- set SW7 to OFF (left) to activate this feature (available for 4-wire stations only)
* - For PK543 Compatible mode, set SW4 OFF, SW5 ON, SW6 ON & SW7 ON.
Also remove JP5 shunt, set J2 to shunt 1 - 2 and set J1 shunt to 2 - 3.
Drawing Name & Number: IN-826 PK543A Shunts and Settings RY-014B Wiring Rev3 051506 1
Page 6 • IN-826 PK-543A Installation Instructions
Copyright © Lee Dan Communications, Inc. All Rights Reserved.
3
Tone in
X
Listen
Talk
Door
1
Post Office Lock
Adapter
Apartment Call Buttons
(Typical)
ENTRY PANEL
Figure 4 - Theory Diagram
LL+
D
K
C
P
G
A
E
5
3
2
1
ZW
Z
CONNECT TO
120 VAC
(-) DC Door power
(+) DC Door power
Switched AC door release
AC Input (Common)
AC Input
Strobe (LI404) power (+24VDC)
Entry speaker common
Entry speaker switched audio
5 Wire station door release
3 wire station audio
Audio to station
Audio from station
Audio Common
Warble tone out
Tone out
PK543A Amplifier
16V AC Doorstrike Configuration
PS-3A, PS-3B
TRANSFORMER
YEL
YEL/BLK
BRN
RED
ORG
WHT/BLK
ORG/BLK
BLK
WHT
GRN
GRY
VIO
BLU
RED/WHT
BRN/WHT
16 VAC
Drawing Name & Number: IL826 PK543A Theory Rev0 050704 1
Audio from station
2
Audio Common
Example of internal connections
of 4 Wire Intercom Station
(most common station)
Audio to station
Copyright © Lee Dan Communications,, Inc. All Rights Reserved.
IN-826 PK-543A Installation Instructions • Page 7
Innovations in Communications TM
since 1955
PK-543A
SPECIFICATIONS
APPLICATION
The PK-543A Power Pack Intercom Amplifier is a selfcontained unit not requiring an external amplifier. The
PK-543A is designed for use with most 3-4-5 wire apartment
stations and provides amplification control and power circuits
needed to operate a complete apartment intercom system.
Voice volume control and tone volume control are easily
adjustable through the screwdriver slot on the front panel.
PK-543A is the most popular and most versatile
apartment intercom amplifier
Additional functions include multi-entrance operation with the
PK-502B, AC or DC door operation selectable by terminal
connection with selectable delayed action door release set at the
dip switch, post office door lock release and a tone signal to
call remote stations. A steady or warble tone can be used to
identify calling from the main entrance panel and a call button
located at the suite entrance.
SPECIFICATIONS
Dimensions:
Height: 5 1/2" Width: 3 1/8" Depth: 2"
Construction:
Rugged ABS Plastic Casing.
Amplification:
Integrated circuit amplifier including
amplifier with frequency response adjusted
for best voice articulation.
Call Tone:
ARCHITECTS' AND ENGINEERS'
SPECIFICATIONS
The intercom amplifier shall be a LEE DAN model
PK-543A or approved equal and shall provide the amplification, control and power circuits needed to operate the
entire intercom system. Amplifier shall feature integrated
circuit amplification, integrated circuit tone call oscillator,
adjustable volume and tone volume controls. Amplifier
shall provide for AC or DC door release operation
selectable by terminal connection and selectable delayed
door timing of 8 seconds or 16 seconds selected at the DIP
switch. A steady or warble tone is available to identify
calling entrance.
Low voltage wiring shall be used and plug-in type
terminals shall be provided for installation wiring.
Non plug-in connectors shall not be acceptable.
The PK-543A shall be mountable to the rear of specifically designed LEE DAN apartment entrance speaker
panels.
STATION COMPATIBILITY:
PK-543A is compatible with these LEE DAN
apartment intercom stations:
Integrated circuit oscillator.
IR-081B, IR-081C, IR-081D
Door Release:
AC or DC operation with selectable timing.
IR-082A, IR-082C, IR-082D
P.O. Release:
P.O. door lock release.
IR-103B, IR-103E,
Connections:
Polarized plug in type.
Power Req.:
16 VAC, 10VA
IR-104B, IR-104E,
IR-105B, IR-105E
IR-107A, IR-107AG, IR-107C, IR-107CG, IR-107D, IR-107DG, IR-147A
IR-203, IR-203E,
IR-204, IR-204E,
IR-205, IR-205E
IR-207, IR-207A, IR-207B, IR-207S, IR-207SS
Mounting:
Replaces:
Surface, or mount to the rear of specifically
designed apartment entrance speaker panels.
LEE DAN® models: PK-543, PK-104B,
PK-103B, PK-103A, PK-101A. Also replaces
many other brands and models (call for info).
IR-307, IR-307A, IR-307C, IR-307D
IR-403, IR-404, IR-405, IR-413, IR-414, IR-415
IR-423, IR-424, IR-425, IR-433, IR-434, IR-435
IR-443, IR-443SS, IR-444, IR-444SS, IR-445, IR-445SS
IR-453, IR-454, IR-455
IR-463, IR-463SS, IR-464, IR-464SS, IR-465, IR-465SS
PK-543A compatible stations can often, but not always be intermixed
within a system. Contact factory to verify compatibility.
800-231-1414 • 631-231-1414
155 Adams Avenue • Hauppauge, NY 11788-3699
Fax 631-231-1498 • www.LEEDAN.com
Page 8 • IN-826 PK-543A Installation Instructions
INTERCOMS • MAILBOXES • DIRECTORIES
ANNUNCIATORS • WIRE & CABLE • NURSE-CALL
With continuous product improvement, specifications are subject to change without notice.
Copyright © Lee Dan Communications, Inc. All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement