Specification
Model:
Picture Type:
Image Sensor:
XIR501
Day/Night (B/W &Colour)
Sony 1/3” Super HAD CCD
DSP:
Resolution:
Lens Viewing Angle:
Infra Red Nightvision:
Minimum Illumination:
Xvision IXC1DN
480 TVL
78°
15 metres
0.1 Lux
Audio:
Operating Voltage:
No
12V DC 750mA
Suggested Power Supply: 12V DC 1250mA Regulated
Mounting: Ceiling
Weatherproofing:
Dimensions (ØxH):
No
133x84mm
CCTV
TECHNICAL SUPPORT:
For Technical Support for any Xvision product please contact your local distributor.
LIMITED WARRANTY:
This product is supplied with a 2 Year warranty. The Warranty excludes products that have been misused, (including accidental damage) and damage caused by normal wear and tear. In the unlikely event that you encounter a problem with this product, it should be returned to the place of purchase.
Manufactured exclusively for:
Xvision (Europe) Group,
Head Office: London, U.K.
Web: www.x-vision.co.uk
CCTV
Model:
XIR501
Colour Dome Camera with 15m Nightvision
Before you begin
•
Please unpack the box carefully and identify that all the parts are present.
The camera is suitable for indoor use only (unless used with an optional external housing).
Please bear in mind the following points when choosing a mounting position.
•
The camera must be positioned so that it will not point directly into the sun (sunrise and sunset) or any bright light, as this may cause damage to the camera.
•
Avoid viewing areas where half the area is in bright sunlight and the other half is dark, such as in the shadow of a building. All types of cameras have difficulty in ‘seeing’ with such a large lux level variation.
•
Do not cut the camera cables, this will void the warranty.
•
Make sure you use only the recommended power supply. Damage caused to the camera by incorrect voltage or wiring is not covered by the warranty.
Model:
XIR501
Colour Dome Camera with 15m Nightvision
Package Contents Installation
STEP 1: Select a suitable position on the wall or ceiling to install the camera.
STEP 2: Rotate the dome housing counterclockwise to remove it from the mounting base (as shown in the figure below).
Note! The inner parts may differ depending on the camera model type.
1. Instruction Manual
2. XIR501 Dome Camera
3. Plastic Bag- containing
4. 4x Bracket mounting screws
5. Countersunk Head Screw
Description
THANK YOU VERY MUCH FOR PURCHASING OUR PRODUCT
The XIR501 colour dome camera is designed for medium to high risk applications. It offers very high resolution 480 TVL images from its Sony 1/3" Super HAD CCD sensor and will provide images in complete darkness up to 15 metres and beyond
15 metres in light levels above 0.1 lux. The camera is designed for internal use and ceiling mounting.
Main Features
• Dual mode High Resolution CCD sensor provides very good quality Colour images in low light conditions of 0.1 lux or above and B/W images in low light conditions below 0.1 lux and in complete darkness.
• Integrated Long Life Infra Red LEDs turn on automatically when the camera switches to B/W mode and provide up to 15 metres night vision
• Tamper resistant and easy to clean as all moving parts are behind the dome cover
• Sony 1/3" Super HAD CCD image sensor for 480 TVL resolution images and 0.1 lux low light sensitivity
• Xvision IXC1DN Digital Signal Processing (DSP) chip which has been optimised for internal viewing and features Automatic Gain Control, Automatic Electronic
Iris, Auto White Balance, Back Light Compensation, Low Smear, Edge
Enhancement, Zero Colour Rolling and Day/Night
• 3.6mm focus free lens for a 78° viewing angle
STEP 3: Place the mounting base onto the ceiling and centre over the mounting hole, using the four retaining screws for the bracket
(A) supplied in the accessories package (shown in the figure below).
STEP 4: Set the proper image by moving the camera body (some model types limit the PCB board to 180° rotational adjustment) and set the focus by turning the lens either to the left or to the right.
When the camera is correctly focused, rotate the dome housing clockwise to secure it to the mounting base.
STEP 5: Lock the dome by using the countersunk head screw supplied.
How to Operate
1. Connect the video output to the monitor or other video device through a 75 Ohms type coaxial cable.
2. Connect the DC jack with the power source.
