BEGLEC IM-7S User guide

BEGLEC IM-7S User guide
iMove 8W Moving Wash
Innovation , Quality , Performance
WWW.BEGLEC.COM
7. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in which
TABLE OF CONTENTS
the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.
1. Safety Instruction
Ÿ Clean with soft cloth using normal glass cleaning fluid.
Ÿ Always dry the parts carefully.
2. Technical Specification
Ÿ Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
3. Lamp
4. How To Set The Unit
4.1 Control Panel
4.2 Main Function
EC Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL:2000+A12:2002
Safety of household and similar electrical appliances
Part 1 : General requirements
2A
5. How To Control The Unit
5.1 Master/Slave Built-In Preprogrammed Function.
5.2 Easy Controller
5.3 iSolution Operation / DMX Controller
5.4 DMX512 Configuration
5.5 DMX512 Connection
6. Troubleshooting
7. Fixture Cleaning
1. Safety Instruction
Pay attention to the belt tension when install the belt.
Please read carefully the instruction, which includes important
information about the installation, usage and maintenance.
Please refer to the photos below:
WARNING
l
Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
l
Unpack and check carefully there is no transportation damage before using the
unit.
l
Before operating, ensure that the voltage and frequency of power supply match the
power requirements of the unit.
l
The unit is designed for use with the MSD 250/2 or NSD250/2. Do not use any other
type of lamp.
l
It’s important to ground the yellow/green conductor to earth in order to avoid
electric shock.
l
The unit is for indoor use only. Use only in a dry location.
l
The unit must be installed in a location with adequate ventilation, at least 50cm
Photo 1
from adjacent surfaces. Be sure that no ventilation slots are blocked.
l
Disconnect main power before fuse/lamp replacement or servicing.
l
Replace fuse/lamp only with the same type.
l
-
3A
Make sure there are no flammable materials close to the unit while operating, as it
is fire hazard.
l
Use safety chain when fixes this unit. Don’t handle the unit by taking its head only,
but always by taking its base.
l
Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature
is higher than this.
l
Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand
during its operation, and allow about 15 minutes to cool down before replacing
bulb or serving, as the unit could be very hot.
l
In the event of serious operating problem, stop using the unit immediately. Never
try to repair the unit by yourself. Repairs carried out by unskilled people can lead
to damage or malfunction. Please contact the nearest authorized technical
assistance center. Always use the same type spare parts.
l
Don’t connect the device to any dimmer pack.
l
Do not touch any wire during operation as high voltage might be causing electric
shock.
Photo 2
Warning
G. If The pan belt is broken
l
1. Turn off the main power.
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
2. Unscrew all the screws (A) and open the base-housing cover (B).
l
Never touch bulb with bare fingers, as it is very hot after using.
3. Unplug all the connect wires (C) that from the arm to PC board and igniter.
l
Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.
4. Unscrew the screws (D) that fix the bridge (E).
l
Do not start on the unit without bulb enclosure or housing are damaged.
l
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
5. Unscrew the screws (F) that fix the axis gear (G).
damaged.
6. Change a new belt (H) by going through all connecting wires that from the arm to base,
l
Do not look directly at the light while the bulb is on.
and through the bridge for correct position.
7. Set up the gear axis to the bridge and screwed it. Note: do not press the belt.
Caution
8. Put the belt around the axis gear and motor gear.
There are no user serviceable parts inside the unit. Do not open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact
9. Plug all the connect wires (C) that form the arm to PC board and igniter.
your nearest dealer.
10. Adjust the pan home position.
11.Screw the base-housing cover (B).
Installation
The unit should be mounted via its mounting system ( as shown below ) on the bottom of the
-
4A
base. Use clamps to fix the unit to truss. Always ensure that the unit is firmly fixed to avoid
vibration and slipping while operating. Always ensure that the structure to which you are
attaching the unit is secure and is able to support a weight of 30 kgs for each unit.
2. Technical Specification
6. Troubleshooting
Following are a few common problems that may occur during operation. Here are some
Power supply
- AC 120V ~ 60Hz / 230V ~ 50Hz
suggestions for easy troubleshooting:
Lamp
- Discharge lamp MSD 250/2 GY 9.5
A. The unit does not work, no light and the fan does not work
1. Check the connect power and main fuse.
Optical system
- High efficiency optical system
2. Measure the mains voltage on the main connector.
- High quality optical lens and dichroic colors
3. Check the power on LED.
- Manually adjustable beam angle: 16°~26°
B. Not responding to DMX controller
Shutter/Dimmer
- Blackout, 0~100 smooth dimming and strobe speed variable(1~10 flashes per second).
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
Color wheel
2. If the DMX LED is on and no response to the channel, check the address settings and
- Independent color wheel with 9 dichroic mirrors plus white.
DMX polarity.
- Color wheel rotates with variable speed, giving rainbow effect.
CMY Mixing system
- Cyan: 0 ~ 100%, Magenta: 0 ~ 100%, Yellow: 0 ~ 100%
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of
Effect Wheel
4. Try to use another DMX controller.
the unit or the previous one.
- Frost filter and diagonal lens
Movement
-
- Pan: 540° in 2.8 second.
- Tilt: 270° in 1.6 second.
5A
5. Check in the DMX cables run near or run alongside to high voltage cables that may cause
damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
DMX Channels
- Standard DMX512 signal addressing and can be controlled by any universal DMX
1. You may have a break in the DMX cabling. Check the LED for the response of the master/
slave mode signal.
controller.
16 Channels:
2. Wrong DMX address in the unit. Set the proper address.
Channel 1 = Pan motion
Channel 9 = Cyan
Channel 2 = Tilt motion
Channel 10 = Magenta
Channel 3 =Pan/Tilt Speed select
Channel 11 = Yellow
Channel 4 = Dimmer
Channel 12 = CMY Speed
Channel 5 = Shutter
Channel 13 = Effect Wheel
Channel 6 = Color
Channel 14 = Pre-programmed Show Pattern
Channel 7 = No Function
Channel 15 = Pre-programmed Beam Pattern
Channel 8 = CMY Mix color/Reset
Channel 16 = Reset
D. No response to the sound
1. Check the unit that is not receiving DMX signal.
2. Check microphone to see if it is good by tapping the microphone
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
1. The lamp is not working well. Check the main voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan on the
head.
5.5. DMX512 Connection
8 Channels:
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
Channel 1 = Pan motion
Channel 2 = Tilt motion
Channel 3 = Shutter
Channel 4 = Effect wheel
Channel 5 = Color
Channel 6 = CYM Mix Color
Channel 7 = Dimmer
Channel 8 = CMY Speed
Dimension: 397 x 360 x 512 mm (L x W x H)
Weight: 27 kg
Luminous intensity:
1. If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pin adapter.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm 1/4W
resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the
DMX-output of the last unit.
3. Connect the unit together in a “daisy chain” by XLR plug from the output of the unit to the
input of the next unit. The cable cannot be branched or split to a “Y” cable. DMX512 is a
very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
connectors can easily distort the signal and shut down the system.
4. The DMX output and input connectors are pass-through to maintain the DMX circuit, when
power is disconnected to the unit.
5. Each lighting unit needs to have an address set to receive the data sent by the controller.
The address number is between 0-511 (usually 0 & 1 are equal to 1).
6. The end of the DMX512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
6A
3. Lamp
In case of replacement of the lamp or maintenance, do not open the
fixture within 15 minutes until the unit cools down after switching off.
Because of its high internal pressure, there might be a risk that the Discharge lamp would
explode during operation. The lamp emits intense UV radiation which is harmful to the
eyes and skin. The high luminance of the arc can cause severe damage to the retina if
looks directly at the lamp.
Discharge lamp:
MSD 250/2 GY 9.5
1. Always switch off the main supply and never handle the lamp or luminaries when is hot.
2. Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured
alcohol and wipe it with a lint free cloth before installation.
3. The lamp generates UV radiation. Never operate the lamp without appropriate shielding.
4. When burning, the lamp operates at high pressure and there is a slight risk of arc tube
rupture. The risk increases with age, temperature and improper handling of the lamp. Do
not use the lamp any longer than its specified life.
5. Make sure the lamp is located in the center of the reflector for the best spot. Adjust lamp
position by screws A, B and C.
-
7A
i.) Channel 14 –Pre-programmed show pattern:
1.) DMX value 0-31,the fixture is still controlled by DMX control .
2.) For DMX Value above 31,all the DMX control will be invalid .The fixture will
run the pre-programmed show patterns(Pan/Tilt movement).
ii.) Channel 15-Pre-programmed beam pattern:
One can select the beam pattern only when the pre-programmed show pattern is
activated.
iii.) For DMX Reset, put DMX value of CH-8 & CH-16 to 255.
5.4. DMX512 Configuration
4. How To Set The Unit
4.1. Control Panel
Display
To show the various menus and the selected functions .
LED
-
8A
DMX
MASTER
SLAVE
SOUND
On
On
On
Flashing
DMX input present
Master mode
Slave mode
Sound activation
MENU
DOWN
UP
ENTER
To select the programming functions
To go backward in the selected functions
To go forward in the selected functions
To confirm the selected functions
Button
Remote controller input
By connect to the 1/4” microphone jack to control the unit for Stand by, Function, and Mode
function.
Sensitivity
To adjust the sound-receiving sensitivity .
Microphone
To receive audio signal for sound activation .
DMX input/output
For DMX512 link, use 3-pin XLR plug cable to link the unit together.
4.2. Main Function
Stand by
To select any of the pre-set functions, press the MENU button up to when the required one is
shown on the display. Select the function by ENTER button and the display will blink. Use
Function
DOWN and UP button to change the mode. Once the required mode has been selected,
press the ENTER button to setup or it will automatically return to the main functions without
Mode
any change after idling 8 seconds. To go back to the functions without any change press the
Blackout the unit
Strobe
1. Color sync. strobe
2. Sync. strobe
3. Two-light strobe
X/Y moving show pattern Color selection
selection
( Show 1 ~ Show 4 )
Please refer to 4.2. Main
Functions- Show mode
X/Y moving setting
1.Pan position
2.Tilt position
3.Dimmer
First set Master unit, then
set Slave units’ position
Sound 1
(LED off )
Sound 2
(LED normal blinking)
Position/ Latch
(LED fast blinking)
Slow/Sound 3
(LED on)
MENU button. The main functions are shown below:
5.3.1 iSolution Operation
DMX512 Address Setting
·Consistent DMX configuration enable iRock and iShow to be linked together and controlled
Setting 16 Channel
Setting 8 Channel
Show
Show
Show
Show
·DMX address can be set remotely by iLead controller ( please refer to the user manual of
mode 1
mode 2
mode 3
mode 4
Slave Mode " Normal "
Slave mode " 2 Light Show "
Blackout Mode " Yes Blackout "
Blackout Mode " No Blackout "
Pan Normal
Pan Inversion
Tilt Normal
Tilt Inversion
Dimmer Normal
Dimmer Inversion
MENU
at the same time.
LED on
LED off
Display Normal
Display Inversion
Focus Adjust
iLead controller ). No need to calculate the DMX channels of each fixture in the chain.
·Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
If you use a universal DMX controller to control the units, you have to set DMX address from 1
to 512 channel so that the units can receive DMX signal.
-
9A
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when the
display stops blinking or storing automatically 8 seconds later. To go back to the functions
without any change press the MENU button again.
Please refer to the following diagram to address your DMX512 channel for the first 4 units.
16 Channels:
Self-Test
Fixture Hours
8 Channels:
Reset
You have to set the fixture DMX address in 8 channels mode when you use IL-0824 controller.
DMX address can be set remotely by IL-0824 controller. No need to calculate the DMX
DMX512 Address Setting
channels of each fixture in the chain.
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Please refer to the following diagram to address your DMX512 channel for the first 4 units.
Once the address has been selected, press the ENTER button to setup or automatically
8 Channels:
return to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.
5. How To Control The Unit
Channel Mode
You can operate the unit in three ways:
Press the MENU button up to when the
is shown on the display. Pressing
1. By master/slave built-in preprogram function
ENTER button and the display will blink. Use DOWN and UP button to select the
2. By easy controller
(16 Channel ) or
(8 Channel) mode. Once the mode has been selected, press
the ENTER button to setup or automatically return to the main functions without any
3. By IL-0824 ( please refer to the user guide of iLead controller ) or universal DMX
controller
change after 8 seconds. To go back to the functions without any change press the MENU
button again.
No need to turn the unit off when you change the DMX address, as new DMX address setting
will be effected at once. Every time you turn the unit on, it will show IM-8W on the display and
Show Mode
move all the motors to their ‘home’ position and you may hear some noises for about 20
seconds. After that the unit will be ready to receive DMX signal or run the built-in programs.
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
5.1. Master/Slave Built-In Preprogrammed Function
(show 1) or
(show 2) or
(show 3) or
(show 4) mode. Once the mode has been
selected, press the ENTER button to setup or automatically return to the main functions
without any change after 8 seconds. To go back to the functions without any change press the
You can select blackout mode
in
(yes blackout) or
(no blackout)
mode while the unit is turned on. By linking the units in master/slave connection, the first unit
MENU button again.
will control the other units to give an automatic, sound activated, synchronized light show. This
function is good when you want an instant show. You have to select
(show 1) or
(show 2) mode by easy controller. Its DMX input jack will have nothing plugged into it,
and Its master LED will be constantly on and sound LED will flash to the music. The other
-
10A
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on the speaker, The spot is always projecting
to the audience’s direction; i.e in front of the stage. Pan movement angle ( left to
units will have to set in slave mode
and select
(normal) or
(2 light
show) mode, Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave
right to left ): 160°.
LED lights will constantly on.
horizon.)
2-light show
In
(slave mode),
means the unit works normally and
2-light show. In order to create a great light show, you can set
get contrast movement to each other, even if you have two units only.
means
on the second unit to
Tilt movement angle:
90° (
60° above horizon; 30° below
Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in
front of the stage. Pan movement angle ( left to right to left ) :160°. Tilt movement angle:
90° ( vertically, front 75°; back 15° )
Slave Mode
5.2. Easy Controller
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
The easy remote control is used only in master/slave mode. By
(normal) or
connecting to the 1/4” microphone jack of the first unit, you will find that
(2 light show) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
the remote control on the first unit will control all the other units for
back to the functions without any change press the MENU button again.
Stand by, Function and Mode.
Display Inversion
Blackout Mode
Press the MENU button up to when the
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
is shown on the display. Pressing ENTER
(display inversion), It will automatically store after 8 seconds. Or press the ENTER
blackout) or
(no blackout) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change after
button again return to the mode
the MENU button.
8 seconds. To go back to the functions without any change press the MENU button again.
Pan Inversion
Press the MENU button up to when the
(display normal). To go back to the functions press
Display normal mode for the fixture putting on the floor.
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
Display inversion mode for the fixture fixing under ceiling.
(normal) or
(pan inversion) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
Focus Adjust
back to the functions without any change press the MENU button again.
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button, the unit will focus on tilt 90°, and then the unit will first focus on pan 0°, pan 90°, pan
Tilt Inversion
Press the MENU button up to when the
is blinking on the display. Use the ENTER button to change to the mode
when the
(yes
button and the display will blink. Use DOWN and UP button to select the
180°, pan 270° each time your press ENTER button. Use DOWN and UP button to adjust
focus. To go back to the functions press the MENU button again.
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(normal) or
(tilt inversion) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
back to the functions without any change press the MENU button again.
-
11A
Self-Test
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the unit will run self-test by built-in program. To go back to the functions press the
MENU button again.
Dimmer Inversion
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(normal) or
(dimmer inversion) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8
Fixture Hours
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button again.
seconds. To go back to the functions without any change press the MENU button again.
Reset
Led Display
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(Led on) or
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and all channels of the unit will return to their standard position. To go back to the
functions press the MENU button again.
DMX RESET :
(Led off) mode. Once the mode has been selected, press the ENTER button to setup
or automatically return to the main functions without any change after 8 seconds. To go back
Set DMX value of channel 8 and channel 16 to 255, then all channels of the unit will return to
to the functions without any change press the MENU button again.
their standard home position.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement