CHROME VELOCIRAPTOR AIR CLEANER, TWIN CAM
9513
THANK YOU FOR CHOOSING CRUSHER!
PROTECT YOURSELF AND OTHERS FROM POTENTIAL INJURY AND PROPERTY DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS, AND NOTICES REGARDING THE INSTALLATION, USE, AND CARE OF THIS PRODUCT.
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED
HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indica on alerts you to the fact that ignoring the contents described herein may nega vely affect product performance and func onality or damage the product itself or the product to which it is being a ached.
THIS PRODUCT IS NOT LEGAL FOR SALE OR USE ON POLLUTION CONTROLLED VEHICLES.
ENSURE THAT THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:
1 Velociraptor Air Cleaner Assembly
1
1
Filter Element
Crankcase Breather Kit
2 Breather Bolts
1
6
3
1
1
1
90 Degree Fi ng
Cable Ties
1/4”‐20 x 7/8" Socket Head Cap Screws
Gasket with Adhesive
O‐Ring
Breather Adapter
1
3
2
1/4”‐20 X 5/8” Socket Head Cap Screw
Breather Hoses
Installa on Instruc ons
YOU WILL ALSO NEED:
Set of Hex Wrenches, Set of Combina on Wrenches
STEP 1
These installa on instruc ons contain important informa on. Ensure that the end user receives this copy and is aware of its importance for future use.
Read and understand all STEPS in the instruc ons before star ng the installa on. Park the motorcycle on a hard, level surface and turn IGN OFF. Allow the engine and exhaust system to cool. Remove the main fuse.
THE END USER’S SAFETY DEPENDS UPON PROPER INSTALLATION OF THIS PRODUCT. IF A
STEP IN THESE INSTRUCTIONS IS NOT WITHIN YOUR CAPABILITIES OR YOU DO NOT HAVE
THE CORRECT TOOLS, HAVE YOUR DEALER PERFORM THE PROCEDURE. IMPROPER IN‐
STALLATION OF THIS PRODUCT COULD RESULT IN DEATH OR SERIOUS INJURY.
ACCIDENTAL VEHICLE START‐UP COULD CAUSE DEATH OR SERIOUS INJURY, REMOVE THE
MAIN FUSE BEFORE PROCEEDING.
INSTALLATION REQUIRES CONTACT WITH THE EXHAUST SYSTEM. ENSURE THAT THE EX‐
HAUST SYSTEM HAS FULLY COOLED BEFORE BEGINNING TO PREVENT INJURY.
9513‐11CR‐0715
STEP 2
STEP 4
STEP 5
Remove the exis ng air cleaner so that the intake flange is completely ex‐ posed. Carefully remove any exis ng gasket material from the flange. Ensure that the flange is clean and dry.
Refer to PIC 1. Ensure that the bike is equipped with an induc on module bracket BEFORE installing the air cleaner.
PIC 1
INDUCTION
MODULE
BRACKET
Refer to PIC 2. Replace the exis ng breather bolts with the two (2) included
Breather Bolts.
If not equipped, use Kuryakyn P/N 9929 Chrome Twin
Cam Intake Support Bracket (sold separately) or H/D
P/N 27711‐08 (sold separately).
PIC 2
REMOVE AIR CLEANER
BREATHER BOLTS
STEP 6
Locate the included Breather Hoses.
Refer to PIC 4 and 5. Trim 1/4” from each end of BOTH of the Hoses.
Connect the Hoses to the Adapter assembly fi ngs; connect the other ends
to the Breather Bolts.
Ensure that the Hoses are free of kinks or ght bends. Secure the ends of the two Hoses with the included Cable Ties; trim the excess Cable Tie ends.
PIC 4
STEP 7
Refer to PIC 3. Locate the included Breather Adapter, O‐Ring, and Fi ngs.
Assemble the Breather Adapter and Fi ngs as shown in PIC 3. The fi ngs should point away from each other.
Press the included O‐Ring into the channel on the backside of the Adapter.
PIC 3
PIC 5
90 DEGREE FITTINGS
ADAPTER
TRIM
BACK 1/4”
STEP 8
Locate the included Gasket with Adhesive.
Remove and discard the adhesive backing from the included Gasket; align it with the Adapter and press it into place.
PIC 5 SECURE WITH CABLE TIES
Align the Adapter assembly with the intake flange; a ach it to the flange with the three (3) included 1/4”‐20 X 7/8” Socket Head Cap Screws.
TRIMMED
HOSE
2
STEP 9
STEP 10
STEP 11
STEP 12
STEP 13
STEP 14
Refer to FIG 1. Completely disassemble the Velociraptor
Assembly. Make note as to how it is assembled, it will help for reassembly.
FIG 1
SUPER RING
Refer to FIG 1. Locate the Velocity Stack.
Align the Velocity Stack and the threaded holes in the
Adapter; secure the Velocity Stack to the Adapter with the three (3) included 1/4”‐20 X 5/8” Socket Head Cap
Screws.
Ensure that the O‐Ring on the backside of the Adapter
remains in place.
DO NOT over ghten the screws!
VELOCITY STACK
FILTER ELEMENT
PIC 6
SCREEN
TRIM RING
SUPER RING “SNAPS” IN
Refer to FIG 1 and PIC 6. Locate the included Super Ring.
“Snap” the Ring into place; ensure it is secure before con nuing.
Locate the included Filter Element, Screen, and Trim Ring.
Place the Filter in the Velocity Stack.
Align the holes in the Screen with the Outer Ring; cover the Filter with the Screen and Trim Ring; secure with the five (5) 1/4”‐20 x 1/2” Socket Head Cap Screws.
Reinstall the main fuse. Double check the ghtness of all related fasteners, check for hose clearance and check thro le for correct opera on, making sure it returns properly, before star ng bike.
FAILURE OF THE THROTTLE TO RETURN COULD RESULT IN LOSS OF CONTROL CAUSING
SERIOUS INJURY OR DEATH.
It is the end user’s responsibility to ensure that all fasteners (including pre‐assembled) are ghtened before opera on of the motorcycle. Kuryakyn will not provide warranty coverage on products or components lost or damaged due to improper installa on or lack of maintenance. Periodic inspec on and maintenance are required on all fasteners.
3
Proper tuning is important. Carbureted bikes should be re‐je ed and fuel injected bikes should be tuned with a TTS MasterTune tuning system (calibra ons available at www.kuryakyn.com) or Vance & Hines FP3 (calibra ons available at h p://fp3.vanceandhines.com/download) by an experienced tuner, on a dyno, with an exhaust gas analyzer.
LIMITED WARRANTY
Küryakyn warrants that any Crusher products sold hereunder, shall be free of defects in materials & workmanship for a period of one (1) year from the date of purchase by the consumer excep ng the following provisions:
1. Küryakyn shall have no obliga on in the event the customer is unable to provide a receipt showing the date the customer purchased the product/s.
2. The product must be properly installed, maintained & operated under normal condi ons.
3. Küryakyn shall not be liable for any consequen al & incidental damages, including labor & paint, resul ng from failure of a Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condi on, or for any breech of contract or duty between Küryakyn & a customer.
4. Crusher products are o en intended for use in specific applica ons. Küryakyn makes no warranty if a Küryakyn product is used in applica ons other than intended.
5. Crusher electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D.’s contained in components of Küryakyn prod‐ ucts will be warranted for defects in materials & workmanship for 3 years from the date of purchase where as all other components shall be warranted for one (1) year.
6. Exhaust systems are warranted for manufacturing defects only. There is no warranty on exhaust pipes & mufflers with regard to any discolora on. Discolor‐ a on or “bluing” is caused by tuning characteris cs, exhaust ming, carburetor je ng, overhea ng, etc. & is not caused by defec ve manufacturing.
7. Küryakyn makes no warranty of any kind in regard to other manufacturer’s products distributed by Küryakyn. Küryakyn will pass on all warran es made by the manufacturer & where possible, will expedite the claim on behalf of the customer, but ul mately, responsibility for disposi on of the warranty claim lies with the manufacturer.
8. Merchandise purchased directly from Internet auc on sites or any other third party seller is considered sold as is & shall not carry a Küryakyn warranty. All warranty claims must be directed to the original seller. If unsure please contact the seller to verify they are an authorized Küryakyn retailer.
RETURN POLICY
Merchandise determined to be defec ve may be returned up to one year from the date of purchase. Returns must be processed through original seller. Re‐ turned merchandise for any other reason other than warranty claims must be in like new condi on & subject to a 20% restocking fee. All returns are subject to inspec on for determina on of full or par al credit. Any returned part that shows evidence of being used or installed contrary to manufacturer’s instruc ons,
&/or subjected to improper handling, packaging or return shipping by the customer, will not be eligible for exchange, refund or warranty considera on. All returned electrical items will be inspected & tested. If electrical item is deemed func onal, no credit will be issued & item will be returned. All sales are final on discon nued or closeout merchandise.
RETURN INSTRUCTIONS
Contact one of our prompt, courteous Customer Service representa ves toll free at 866‐295‐5759. Be sure to have the following informa on available when you call:
Name
Part number/s to be returned
Copy of original invoice
Reason for return
1. Obtain R.M.A. number which shall remain ac ve & valid for 60 days. (Important: Issuance of R.M.A. does not represent an authorized credit.)
2. Carefully package merchandise to avoid damage during shipment. Depending on its condi on, original packaging may not be sufficient.
3. Ship only those items for which the R.M.A. has been issued.
4. Write the R.M.A. number prominently on the outside of package.
5. Ship package freight PREPAID (C.O.D.s will not be accepted) to:
Kuryakyn 454 County Road V V Somerset, WI 54025
4
