Catalogue Sheet: Retract-a
Project/Location:
Retract-a-Lite™
Series
Contractor:
Date:
Prepared by:
Remote Fixture
FEATURES
TYPICAL SPECIFICATIONS
• Remote only visible upon power failure
Supply and install Emergi-Lite® Retract-a-Lite™ Series of remote
fixture: The unit shall be designed to be concealed in walls or ceilings
with a cavity. The unit equipment shall be completely concealed in the
wall or ceiling in the absence of remote power. Upon DC power supply
the unit will rotate its door by 180° to expose the emergency lamps,
and power them. After the DC power disconnect the lamps will turn
off and the unit will conceal the heads by rotating the door by 180°.
The DC-remote unit shall not require the presence of AC power in
order to open or close the door.
Under normal conditions, the only visible parts of the unit shall be
the off-white flat door and trim plate that can be customized on site
with paint or other suitable wall covering. The light source shall be
MR16 halogen lamps of specified wattage and light output.
The remote unit shall be the Emergi-Lite® model:
.
• Front can be painted or wallpapered on-site to match existing
decor
• Fully automatic operation: The unit door opens upon supply with
DC voltage from battery and closes after voltage disconnect.Time
delay option required on battery unit to properly close the door
• AC line voltage not required
• Emergency lights: Two high efficacy MR16 halogen or MR16 LED
lamps
• Certification: CSA C22.2 No.141
DIMENSIONS
REPLACEMENT LAMPS: MR16
Dimensions are approximate and subject to change.
91/8” [23.1 cm]
DC VOLTAGE
JUNCTION
BOX
71/4” [18.3 cm]
71/4” [18.3 cm]
33/4” [9.6 cm]
WIRE GUARDS
460.0082-E
Wall Mount
MODEL
LAMP TYPE
VOLTAGE/WATTAGE
580.0080-E
MR16 12W Flood
12V-12W
12V-20W
580.0064-E
MR16 20W Flood
580.0083-E
MR16 35W Flood
12V-35W
580.0076-E
MR16 50W Flood
12V-50W
580.0068-E
MR16 IR 20W Flood
12V-20W High-output
580.0090-E
MR16 IR 35W Flood
12V-35W High-output
580.0089-E
MR16 IR 50W Flood
12V-50W High-output
580.0084-E
MR16
24V-35W
580.0070-E
MR16
24V-12W
580.0077-E
MR16
24V-20W
580.0078-E
MR16
24V-50W
580.0093-E
MR16 LED
12V-4W
580.0098-E
MR16 LED
24V-4W
580.0100-E
MR16 LED
24V-6W
580.0104-E
MR16 LED
12V-5W
580.0106-E
MR16 LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
ORDERING INFORMATION
SERIES
12RTLR= 12VDC remote*
24RTLR= 24VDC remote**
* The remote fixture is compatible with all
Retract-a-Lite™ battery units.
WATTAGE FOR EACH OF THE 2 LAMPS
-LG= 2x MR16 LED, 12V-4W
-LI= 2x MR16 LED, 12V-5W
-LL= 2x MR16 LED, 12V-6W
-LJ= 2x MR16 LED, 24V-4W
-LM= 2x MR16 LED, 24V-6W
-12= 2x MR16 halogen, 12W
-20= 2x MR16 halogen, 20W
-35= 2x MR16 halogen, 35W
-50= 2x MR16 halogen, 50W
-20H= 2x MR16-IR, 12V-20W, high output
-35H= 2x MR16-IR, 12V-35W, high output
-50H= 2x MR16-IR, 12V-50W, high output
** 1
2V-24V battery unit must include the time
delay function & exclude diagnostic to close
door: consult factory for details.
EXAMPLE: 12RTLR-20TB
140
OPTIONS
TB= T-Bar mounting kit
Mini
Retract-a-Lite™
Series
Project/Location:
Contractor:
Date:
Prepared by:
For AC Power Generator
FEATURES
TYPICAL SPECIFICATIONS
Supply and install Emergi-Lite® Series Mini Retract-a-Lite™. The
unit shall be designed to be completely concealed in walls with a
cavity. The equipment shall consist of a metal housing containing two
modules joined by a flexible bracket and electric conduit. One module
contains the power transformer and electrical connection box; the
other module contains the emergency lights installed on the back of
a door able to rotate several turns of 360°. The unit equipment shall
be completely concealed in the wall, after the installation through a
rectangular opening not larger than 8.25” by 5.75”.
• Easy to retrofit in finished walls: the unit slides in through an
8.25” by 5.75” hole
• No back-box needed to pre-install
• Output: 12VDC with up to 100W of power
• Direct connection to 120 or 347VAC power generators
• Emergency lights: MR16 halogen and MR16 LED lamps
• Certification: CSA C22.2 No. 141
In stand-by mode, the only visible parts of the unit shall be the
off-white flat door and trim plate that can be customized on site with
paint or other suitable wall covering. Upon AC power supply the unit
will expose the emergency heads by rotating its door 180° and then
will power the lamps. At the end of the AC power, the lamps will turn
off and the unit will retract the heads by rotating the door 180° in the
same direction.
The unit shall not require the presence of AC power in order to close
the door and conceal the lights. The door of the unit shall be easy
to force-turn (open or close) by hand. The light source shall be 12V
MR16 halogen lamps of specified wattage and light output.
The remote unit shall be the Emergi-Lite® model:
DIMENSIONS
Dimensions are approximate and subject to change.
7” [17.8 cm]
COMPLETE UNIT
51/4” [13.2cm]
91/8” [23.2cm]
REPLACEMENT LAMPS
73/4” [19.7cm]
31/2” [8.9 cm]
175/8” [44.9 cm]
INSTALLED UNIT
MODEL
TYPE
VOLTAGE/WATTAGE
580.0080-E
MR16 flood
12V-12W
580.0064-E
MR16 flood
12V-20W
580.0083-E
MR16 flood
12V-35W
580.0076-E
MR16 flood
12V-50W
580.0068-E
MR16 IR flood
12V-20W High output
580.0090-E
MR16 IR flood
12V-35W High output
580.0089-E
MR16 IR flood
12V-50W High output
580.0093-E
MR16 LED
12V-4W
580.0104-E
MR16 LED
12V-5W
580.0106-E
MR16 LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
ORDERING INFORMATION
SERIES
MR
UNIT CAPACITY
G= remote AC generator,
maximum 100W
AC VOLTAGE
Blank= 120VAC
2= 277VAC
3= 347VAC
LAMP WATTAGE (12V MR16)
/12= MR16, 12W
/20= MR16, 20W
/35= MR16, 35W
/50= MR16, 50W
/20H= MR16, High lumen output, 20W
/35H= MR16, High lumen output, 35W
/50H= MR16, High lumen output, 50W
/LG= MR16 LED, 12V-4W
/LI= MR16 LED, 12V-5W
/LJ= MR16 LED, 12V-6W
Note: Testing requires minimum 5 seconds of power supply.
EXAMPLE: MRL80/20HUN
141
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement