Installation Manual for the WARNING! ANNIVERSARY SERIES

Installation Manual for the WARNING! ANNIVERSARY SERIES
Installation Manual for the
ANNIVERSARY
SERIES
HEAVY DUTY
C
LI
STED
US
WARNING!
This equipment is similar to other gate or door equipment and meets or exceeds
Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has
hazards associated with its use and therefore by installing this product the installer
and user accept full responsibility for following and noting the installation and
safety instructions. Failure to follow installation and safety instructions can result
in hazards developing due to improper assembly. You agree to properly install
this product and that if you fail to do so Gates That Open, LLC shall in no event
be liable for direct, indirect, incidental, special or consequential damages or loss
of profits whether based in contract tort or any other legal theory during the
course of the warranty or at any time thereafter. The installer and/or user agree
to assume responsibility for all liability and use of this product releasing Gates
That Open, LLC from any and all liability. If you are not in agreement with this
disclaimer or do not feel capable of properly following all installation and safety
instructions you may return this product for full replacement value.
READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before
attempting to install and use this automatic gate opener. This gate opener
produces a high level of force. Stay clear of the unit while it is operating and
exercise caution at all times.
All automatic gate openers are intended for use on vehicular gates only.
This product meets and exceeds the requirements of UL 325, the standard which regulates gate opener safety,
as established and made effective March 1, 2000, by Underwriters Laboratories Inc.
3121 Hartsfield Road • Tallahassee, Florida, USA 32303
Telephone GTO Sales: 1-800-543-GATE (4283) or (850) 575-0176 • Fax (850) 575-8912
or GTO Technical Service: 1-800-543-1236 or (850) 575-4144 • Fax (850)575-8950
www.gtoaccess.com­
2004 Gates That Open, LLC
©
REV-08/31/11
Printed in China for Gates That Open, LLC
U.L. Gate Operator Classifications
Residential Vehicular Gate Operator—Class I: A vehicular gate operator (or system) intended for use in a home of
one-to-four single family dwelling, or a garage or parking area associated therewith.
Commercial/General Access Vehicular Gate Operator—Class II: A vehicular gate operator (or system) intended for
use in a commercial location or building such as a multifamily housing unit (five or more single family units), hotel,
garages, retail store, or other building servicing the general public.
Industrial/Limited Access Vehicular Gate Operator–Class III: A vehicular gate operator (or system) intended for
use in an industrial location or building such as a factory or loading dock area or other locations not intended to
service the general public.
Restricted Access Vehicular Gate Operator–Class IV: A vehicular gate operator (or system) intended for use in a
guarded industrial location or building such as an airport security area or other restricted access locations not
servicing the general public, in which unauthorized access is prevented via supervision by security personnel.
Product Usage
This Gate Operator meets all of the safety requirements of a Class I Residential Vehicular Gate Operator and is
intended for use solely with vehicular swing gates in single-family residential applications.
This Gate Operator is system certified to be in compliance with the following safety standards (current edition
as of publication date):
Product in compliance with the latest UL-325 and UL-991 safety standards by ETL. Product in
compliance with CAN/CSA-C22.2 No. 247-92.
Product in compliance with IEC 60335-2-103:2003 and IEC 60335-1:2004, including A1:2004.
Converting Metric Units to English Equivalents
When You Know
Multiply By To Find
Symbol
centimeters
meters
kilograms
in. (or ")
ft. (or ')
lb. (or #)
0.3937
3.2808
2.2046
inches
feet
pounds
Converting English Units to Metric Equivalents
When You Know
Multiply By To Find
inches
feet
pounds
2.5400 centimeterscm
0.3048meters m
0.4535 kilogramskg
Converting Temperature
deg. Celsius
deg. Fahrenheit
Symbol
(°C x 1.8) + 32
(°F-32) ÷ 1.8
deg. Fahrenheit
deg. Celsius
°F
°C
FOR YOUR RECORDS
Please record the following information product serial number (located on right side of control box), be sure to
keep all receipts for proof of purchase. Refer to this information when calling GTO for service or assistance
with your automatic gate opener.
Serial Number:____________________________________
Date of Purchase:_________________
Place of Purchase:____________________________________________________________________
Table of Contents
PLEASE READ THIS FIRST________________________________________________________ ii
IMPORTANT SAFETY INFORMATION_____________________________________________ 1
TECHNICAL SPECIFICATIONS____________________________________________________ 8
BEFORE YOU BEGIN_____________________________________________________________ 9
Check Direction of Gate Swing_____________________________________________________ 9
Check Existing Gate Size and Material_______________________________________________ 9
Check for Proper Gate Installation___________________________________________________ 9
Column Installation Information____________________________________________________ 10
Items Included__________________________________________________________________ 10
Tools Needed__________________________________________________________________ 11
Items Not Included______________________________________________________________ 11
GATE OPENER INSTALLATION__________________________________________________ 12
Mounting Pull-to-Open Opener to Gate_____________________________________________ 12
Mounting Push-to-Open Opener to Gate_____________________________________________ 15
CONTROL BOX INSTALLATION_________________________________________________
Control Box Installation__________________________________________________________
Transformer Wiring Installation____________________________________________________
Receiver Installation_____________________________________________________________
18
18
19
21
SOLAR PANEL INSTALLATION__________________________________________________ 22
CONTROL BOX SETTINGS______________________________________________________
DIP Switches___________________________________________________________________
Setting Pull-to-Open (Closed) Gate Limit____________________________________________
Resetting Closed Gate Limit_______________________________________________________
Setting Push-to-Open (Open) Gate Limit____________________________________________
Resetting Open Gate Limit________________________________________________________
Setting Obstruction Stall Force and Auto Close Time___________________________________
Setting Your Personal Code________________________________________________________
24
24
25
25
26
26
27
27
CONNECTING ADDITIONAL DEVICES___________________________________________ 29
Input Connections________________________________________________________________30
Connecting Accessories__________________________________________________________ 31
Connecting GTO Automatic Lock__________________________________________________ 32
Connecting Other Auxilary Devices__________________________________________________32
MAINTENANCE & TROUBLESHOOTING_________________________________________ 32
Maintenance Tips________________________________________________________________32
Troubleshooting Guide____________________________________________________________33
i
Please Read This First!
Thank you for purchasing a GTO/ACCESS SYSTEMS gate opener. When correctly installed and properly used,
your gate operator will give you many years of reliable service. Please read the following information to ensure
you have the correct system for your particular needs. This manual will enable you to properly install your
Automatic Gate Operator.
The gate operator is designed for installation on a pull-to-open single leaf gate. By purchasing an accessory
bracket [347IH], the gate operator can accommodate a push-to-open gate (gate that open out from the property).
The gate must not exceed 18 feet in length nor weigh more than 850 pounds* (please see Technical Specifications
on page 1). The gate operator can be used on vinyl, aluminum, chain link, farm tube, and wrought iron gates. Use
on solid (wood) gates is not recommended. Solid surface gates have a high resistance to the wind. If the wind is
strong enough, the operator will obstruct, stop, and blow fuses.
The gate operator accommodates extra transmitters, digital keypads, solar panels, push buttons, automatic gate
locks, and other access control products. These optional accessories are sshown in the back of this manual.
The gate operator features adjustable stall force. This safety feature makes the gate stop and reverse direction
within two seconds when it comes in contact with an obstruction. The “MIN” setting means the gate will exert
the minimum force on an obstruction before it stops and reverses direction.
The gate operator also has an adjustable auto-close feature. It can be set to remain open from 3 to 120 seconds
before automatically closing. Pressing the transmitter button at any time after the gate fully opens will cause it to
close immediately. “OFF” is the factory setting; meaning the gate will stay open until you press the transmitter
button (or keypad, etc.) again.
Please call GTO at (800) 543-GATE [4283] or (850) 575-0176 for more information about our GTO/ACCESS
SYSTEMS professional line of gate operators and accessories.
BEFORE YOU BEGIN TO INSTALL YOUR AUTOMATIC GATE OPERATOR:
Read these instructions carefully and completely to become familiar with all parts and
installation steps. You must read the installation manual for detailed instructions on gate
operator safety and proper use of the gate operator.
24/7 Troubleshooting Wizard: http://support.gtoinc.com
ii4
Important Safety Information
Because automatic gate openers produce high levels
of force, consumers need to know the potential
hazards associated with improperly designed,
installed, and maintained automated gate opener
systems. Keep in mind that the gate opener is just
one component of the total gate operating system.
Each component must work in unison to provide the
consumer with convenience, security, and safety.
manual cannot be completely exhaustive in nature.
They do, however, provide an overview of the
safe design, installation, and use of this product.
CAREFULLY READ AND FOLLOW ALL
SAFETY PRECAUTIONS, WARNINGS, AND
INSTALLATION INSTRUCTIONS TO ENSURE
THE SAFE SYSTEM DESIGN, INSTALLATION,
AND USE OF THIS PRODUCT.
This manual contains various safety precautions
and warnings for the consumer. Because there are
many possible applications of the gate opener, the
safety precautions and warnings contained in this
Precautions and warnings in this manual are
identified with this warning symbol. The symbol
identifies conditions that can result in damage to the
opener or its components, serious injury, or death.
Because GTO automatic gate openers are only part of the total gate operating system, it is the responsibility
of the consumer to ensure that the total system is safe for its intended use.
Manually Opening and Closing Gate
CAUTION: The gate will move freely and uncontrolled when the gate opener is removed from the
gate. ONLY disconnect the opener when the control box power switch is OFF and the gate is NOT moving.
Disconnecting the Opener
Front Mount
1. Turn control box power switch OFF.
2. Remove hairpin clip, clevis pin, and bushing from
either the front or rear mounting point.
Clevis Pin
Gate Bracket
3. Remove the opener from the mount.
The gate can be opened and closed manually
when the opener is disconnected.
Bushing
Hairpin Clip
NOTE: Substitute the included Pin Lock for the clevis pin on the front
mount of the gate opener to prevent unauthorized removal of the opener
from the gate.
1
Important Safety Information
For the Consumer
WARNING: To reduce the risk of injury or death:
1. READ AND FOLLOW ALL
INSTRUCTIONS. Failure to meet the
requirements set forth in the instruction manual
could cause severe injury or death, for which the
manufacturer cannot be held responsible.
2. Make sure the gate has been properly installed
and swings freely in both directions. Repair or
replace all worn or damaged gate hardware prior
to installation. A freely moving gate will require
less force to operate and will enhance the
performance of the opener and safety devices
used with the system (see page 9).
2. When designing a system that will be entered
from a highway or main thoroughfare, make sure
the system is placed far enough from the road to
prevent traffic congestion.
3. Review the operation of the system to become
familiar with its safety features. Understand how
to disconnect the opener for manual gate
operations (see page 1).
3. The gate must be installed in a location that
provides adequate clearance between it and
adjacent structures when opening and closing to
reduce the risk of entrapment. Swinging gates
must not open into public access areas.
4. This gate opener is intended for vehicular gates
ONLY. A separate entrance or gate must be
installed for pedestrian use (see page6).
4. The gate and gate opener installation must
comply with any applicable local codes.
5. Always keep people and objects away from the
gate and its area of travel. NO ONE SHOULD
CROSS THE PATH OF A MOVING GATE.
I. Before Installation
6. Pay close attention to the diagram below and be
aware of these areas at all times.
1. Verify this opener is proper for the type and size
of gate, its frequency of use and proper class
rating.
ZONE 2
ZONE 1
ZONE 3
Gate in the
Open Position
Entrapment
Zones for a
Push-To-Open
Application
ZONE 5
ZONE 5
ZONE 3
ZONE 4
Entrapment
Zones for a
Pull-To-Open
Application
ZONE 4
Driveway
ZONE 1
Gate in the
Open Position
2
Driveway
ZONE 2
Important Safety Information
For the Consumer
Entrapment Zones for a proper Pull-To-Open installation:
Zone 1 – leading edge of the gate and the fence post.
Zone 2 – between the gate and the gate post.
Zone 3 – the path of the gate.
Zone 4 – the space between the gate in the open position and any object such as a wall, fence, tree, etc.
Zone 5 – pinch points between the opener and gate.
II. During Installation
4. If push buttons or key switches are installed, they
should be within sight of the gate, yet located at
least 10 feet from any moving part of the gate
(see diagram below). Never install any control
device where a user will be tempted to reach
through the gate to activate the gate opener.
1. Install the gate opener on the inside of the property and fence line. DO NOT install an opener
on the outside of the gate where the public has
access to it.
2. Be careful with moving parts and avoid close
proximity to areas where fingers or hands could
be pinched.
5. Do not activate your gate opener unless you can
see it and can determine that its area of travel is
clear of people, pets, or other obstructions. Watch
the gate through its entire movement.
3. Devices such as contact sensors (safety
edges) and non contact sensors (photo beams)
provide additional protection against entrapment.
6. Secure outdoor or easily accessed gate opener
controls in order to prohibit unauthorized use of
the gate.
NEVER install
any control device
within gray area
NEVER install
any control device
within gray area
Pull-To-Open
Application
Push-To-Open
Application
10'
10'
10'
10'
Moving Gate
Area
Moving Gate
Area
Driveway
10'
10'
Driveway
10'
10'
3
Important Safety Information
For the Consumer
III. After Installation
8. To operate this equipment safely, YOU must
know how to disconnect the operator for manual
gate operation (see page 1). If you have read the
instructions and still do not understand how to
disconnect the operator, contact the GTO Service
Department.
9. Disconnect the operator ONLY when the power
is TURNED OFF and the gate is NOT moving.
1. Attach the warning signs (included) to each side
of the gate to alert the public of automatic gate
operation. It is your responsibility to post warning
signs on both sides of your gate. If any of these
signs or warning decals becomes damaged,
illegible, or missing, replace them immediately.
Contact GTO for free replacements.
2. The gate is automatic and could move at any time,
posing serious risk of entrapment. No one should
be in contact with the gate when it is
moving or stationary.
10. Make arrangements with local fire and law
enforcement for emergency access.
11. Distribute and discuss copies of the
IMPORTANT SAFETY INFORMATION
section of this manual with all persons
authorized to use your gate.
3. Do not attempt to drive into the gate area while
the gate is moving; wait until the gate comes to a
complete stop.
12. IMPORTANT: Save these safety instructions.
Make sure everyone who is using or will be
around the gate and gate operator are aware of
the dangers associated with automated gates.
In the event you sell the property with the gate
operator or sell the gate operator, provide a
copy of these safety instructions to the new
owner.
4. Do not attempt to “beat the gate” (drive through)
while the gate is closing. This is extremely dangerous.
5. Do not allow children or pets near your gate.
Never let children operate or play with gate
controls. Keep the remote control away from
children and unauthorized users; store controls
where children and unauthorized users do not
have access to them.
Should you lose or misplace this manual, a
copy can be obtained by downloading one from
the GTO Access Systems web site (www.gtoaccess.com), by contacting Gates That Open,
LLC., at 3121 Hartsfield Road, Tallahassee,
Florida 32303 or by calling 1-800-543-4283
and requesting a duplicate copy. One will be
provided to you for a nominal fee.
6. KEEP GATES PROPERLY MAINTAINED.
Always turn power to operator OFF before
performing any maintenance. Clean the
push-pull tube with a soft, dry cloth and apply
silicone spray to it at least once per month.
7. Service the gate and gate operator regularly.
Grease hinges, clean the push-pull tube by spraying a soft dry cloth with silicone spray and wipe
the tube at least once per month and replace the
battery every 2-3 years.
4
Important Safety Information
Secondary Means of Protection Against Entrapment
As specified by Gate Operator Safety Standard, UL 325 (30A.1.1), automatic gate operators shall have an inherent entrapment
sensing system, and shall have provisions for, or be supplied with, at least one independent secondary means to protect
against entrapment. GTO gate openers utilizes Type A, an inherent (i.e., built-in) entrapment sensing system as the primary
type of entrapment protection. Also, the gate opener has provisions for the connection of Type B1 or B2 protection to be
used as the secondary type of entrapment protection, if desired.
1. For gate operators utilizing a non-contact sensor (e.g., photo-electric sensor– Type B1) in accordance with UL 325
(51.8.4 [h]):
A. Refer to the sensor manufacturer’s instructions on the placement of non-contact sensors for each type of application.
B. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate
is still moving.
C. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the
perimeter reachable by a moving gate or barrier.
For gate operators utilizing a contact sensor (e.g., safety edge sensor– Type B2) in accordance with UL 325 (51.8.4 [i]):
2.
A. One or more contact sensors shall be located at the leading edge, bottom edge, and post edge, both inside and outside
of a vehicular swing gate system.
B. A hard wired contact sensor shall be located and its wiring arranged so that the communication between the sensor
and the gate operator is not subjected to mechanical damage.
C. A wireless contact sensor such as one that transmits radio frequency (RF) signals to the gate operator for entrapment
protection functions shall be located where the transmission of the signals are not obstructed or impeded by building
structures, natural landscaping or similar obstruction. A wireless contact sensor shall function under the intended
end-use conditions.
You may want to consider adding photo beams to your installation. GTO Photo Beams [R4222] provide a “non contact”
means of entrapment protection.
Leading Edge Contact Sensor
on both sides of the gate
®
E-Z GATE OPENER
500
UL325 SERIES
1-800-543-GATE (4283)
www.mightymule.com
Photo Beam
Photo Beam
Vehicular Gate
Bottom Edge Contact Sensor
on both sides of the gate
Post Edge Contact Sensor
on both sides of the gate
ENTRAPMENT ALARM (UL 325; 30A.1.1A)
The GTO® Automatic Gate Operator is designed to stop and reverse within 2 seconds when the gate comes in contact
with an obstruction. Additionally, these operators are equipped with an audio entrapment alarm which will activate if
the unit obstructs twice while opening or closing. This alarm will sound for a period of 5 minutes, or until the operator
receives an intended signal from a hardwired entry/exit source (e.g. push button control or keypad) and the gate returns
to a fully open or fully closed position. Turning the power switch on the control box OFF and back ON will also deactivate the alarm. Wireless controls such as transmitters and wireless keypads will not deactivate the alarm.
5
Important Safety Information
Required Safety Precautions for Gates
Install Warning Signs
Warning signs alert people of automatic gate operation and are required when installing the GTO Automatic
Gate Operator. Furthermore, a walk-through gate must be installed if pedestrian traffic is expected near the vehicular gate. We recommend using the GTO Bulldog Pedestrian Gate Lock (Call the GTO Sales
Department at 800-543-4283) for controlled access.
Bulldog Pedestrian
Gate Lock
(recommended, not included)
Contact Sensors
Pedestrian Gate
(recommended, not included)
Warning Sign
®
E-Z GATE OPENER
500
UL325 SERIES
1-800-543-GATE (4283)
www.mightymule.com
Vehicular Gate
Photo Beams
Contact Sensors
(recommended, not included)
(recommended, not included)
Photo Beams
(recommended, not included)
Entrapment Protection
GTO’s inherent obstruction settings, even when properly adjusted, may not be sensitive enough to prevent bodily
injury in some circumstances. For this reason, safety devices such as safety edge sensors (or photoelectric
sensors), which stop and reverse gate direction upon sensing an obstruction, are suggested for enhanced protection
against entrapment.
Warning Signs
!
The warning signs (at right) must be installed on both
sides of the gate (see next page for details).
6
Important Safety Information
Required Safety Precautions for Gates
!
These warning labels should be found at the
locations specified below. If any of them are
missing, immediately contact GTO for
replacements.
5.5
C
LIS ED
T
US
9901178
Gates That Open, LLC • Tallahassee, Florida USA
Product identification and manual operation instruction
label (1) installed on right hand side of control box.
.
ANNIVERSARY
SERIES
1-800-543-4283
!
HEAVY DUTY
www.gtoaccess.com
WARNING
MOVING GATE
Can Cause Injury or Death
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or play in gate area.
3. This gate is for vehicles only. Pedestrians must use separate entrance.
.
7
Technical Specifications
GTO® Gate Opener
DRIVE
CONTROL
• Low friction screw drive (linear actuator) rated for -5 ºF
to +160 ºF (-20 ºC to +71 ºC). Use of heater bands on arm
and control box will enhance performance in extreme cold
temperatures.
• Powered by a 12 V motor with integral case hardened steel
gear reducer. Motor speed reduced to 260 rpm.
• Maximum opening arc of 110º. Approximate opening time
(90º): 20 seconds, depending on weight of gate.
• GTO microprocessor-based control board is set for single
leaf, pull-to-open gate installations. DIP switches can be
adjusted to accommodate an optional kit for push-to-open
gates (see Accessory Catalog).
• A circuit on the control board regulates charging. “Sleep
draw” is 25 mA; “active draw” is 2 to 5 A.
• Auto-memorization of digital transmitter code.
• GTO remote-mounted RF receiver tuned to 318 MHz.
• Operator length with push-pull tube fully retracted is
40-1/4” mounting point to mounting point. Max stroke 22”.
• Adjustable auto-close timer (3 to 120 s), and obstruction
sensitivity.
• Power terminal block accommodates a transformer or solar
panels. NOTE: Do not use solar panel and transformer
at the same time.
• DIP switches simplify setup of gate operator.
• Accessory terminal block fully compatible with push
button controls, digital keypads, safety loops, etc.
• Control board allows connection of safety edge sensors
and photoelectric sensors.
• Audio entrapment alarm sounds if unit encounters an
obstruction twice while opening or closing.
POWER
• The system is powered by two 12 Vdc, 7.0 Ah, sealed,
rechargeable acid batteries.
• Battery charge is maintained by a 18 Vac output transformer through the GTO control board. Blade-style control
board fuse is rated for 15 A.
NOTE: The transformer should not be directly
connected to any battery. Do not replace fuses with
higher ampere rated fuses; doing so will void your
warranty and may damage your control board.
• OPTIONAL: Battery charge is maintained by GTO Solar
Panel Charger kits (5 Watt minimum).
OPERATIONAL CAPACITY
• The Gate Capacity Chart shows approximate cycles, per
day, you can expect from the GTO Automatic Gate Operator when powered with a transformer. Actual cycles may
vary slightly depending upon the type and
condition of gate and installation.
NOTE: Gray area indicates this
size and weight combination is
not recommended for the SilverHD gate opener.
Silver-HD Single Gate Capacity /Cycle Chart
Estimated number of daily cycles, based on use with a transformer.
Number of Cycles* Per Day
Gate Weight
NOTE: Ball bearing hinges
should be used on all gates
weighing over 250 lb.
850 lbs.
750 lbs.
650 lbs.
550 lbs.
450 lbs.
350 lbs.
250 lbs.
150 lbs.
100 lbs.
50 lbs.
135
145
155
165
175
185
195
205
215
225
5’ - 6’
125
135
145
155
165
175
185
195
205
215
8’
125
135
145
155
165
175
185
195
205
10’
Gate Length
125
135
145
155
165
175
185
195
12’
125
135
145
155
165
175
185
14’
To determine the number of cycles the gate operator will perform using solar panels,
please see the specifications listed on page 22.
* An operation cycle is one full opening and closing of the gate.
These specifications are subject to change without notice.
8
125
135
145
155
165
175
16’
125
135
145
155
165
18’
Before You Begin
Check Direction of Gate Swing
(Requires Push-To-Open Bracket
#347IH—NOT INCLUDED)
Your Property
Your Property
Pull-to-Open Option
Instructions begin on
page 13
Push-to-Open Option
Instructions begin on
page 16
Check Existing Gate Size and Material
• Gate size: Up to 18 feet or up to 850 lbs—See chart
on page 9.
• Type of gate material: Vinyl, aluminum, chain link,
farm tube, wrought iron, wood (not recommended for
solid surface gates).
IMPORTANT: Check for Proper Gate Installation
For the gate opener to work properly, gate must be plumb, level, set in concrete, swing freely and not touch the
ground and have good working hinges.
A
E
F
B
C
A- Level
B - Plumb
C - Free Swinging
D - Secured Posts in Concrete
E - Centerline Mounting
F - Good Working Hinges (ball
bearing hinges are recommended on
gates over 250 pounds)
9
D
Before You Begin
Column Installation Information
IF THIS OPENER WILL BE USED WITH GATES THAT ARE MOUNTED ON MASONRY, BRICK,
OR ROCK (etc.) COLUMNS, READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING
A. The simplest solution is to install the opener in a
push-to-open configuration (requires push-to-open
bracket, see accessory catalog). The minimum
clearance is easier to achieve and clearance is no
longer a problem, since the opener will be pushing
the gate away from the column instead of pulling it toward the column. It is recommended that
you place a steel plate between the opener mounting brackets and masonry surface for additional
strength.
B. If a push-to-open installation is impossible due to
traffic hazards, terrain, etc., another option is to
re-hang the gate. You may hang it on a post, either
in the center of the column or at the back corner, or
move the gate to the back corner of the columns.
C. The most difficult solution is to cut a notch in the
column to accommodate the opener and power
cable. This job is NOT for the inexperienced!
Hinge
Gate
Column
B
Column
AR Mount Example
(A + BNcan
IN not exceed 19 inches)
Example: G
If A is 6" then B cannot exceed 13"
st
all
ati
o
n
O
ve
rv
ie
w
fo
r th
e.
.
Mo
vi
Inj ng G
u a
Ary Or tDe Can
eat Ca
h use
1.
KE
2.
EP
D
CL
pla o no
EA
3.
y in t a
R!
T
Ga
ga llow
mu his g
te
te
ch
st u ate
ma
se is fo area ildre
ym
.
as
n to
ove
ep r veh
op
ara ic
era at an
le
te
y ti
te
en s on
ga
me
tra ly.
te
.
nce Pe
or
de
.
str
ian
s
In
Pivot Bracket
!W
Items Included
Transformer
E
G
C
ra icl
er t a
te es
at ny
e
en o
ga tim
tr nly
an .
t e e.
ce Ped
or
. e
st
ri
an
s
in
In g G
ju a
D
ry te
C
pl o n LE
3.
A
ay ot
O Ca
R!
Th in al
r n
G
g lo
a
m is
D C
us ga ate w c te
ea a
t u te
ar hil ma
se is
y
ea dr
e
th us
f
.
a o
n mo
se r v
to
ve
e
pa eh
op a
Warning
Signs
2.
1.
KE
EP
M
ov
!
W
A
R
N
Operator
Arm
IN
B
J
F
Closed Position
Bracket
Gate Bracket
12
lt
Vo
/
7.0
p
Am
t
un
Mo
12
0
50
RB
A
Receiver and
Control Box
H
Post Pivot Bracket
L
P
7.0
0
50
I
RB
3/8” x 2-3/4” Bolt (2)
3/8” x 2” Bolt (1)
U
W
p
Am
K
t
un
Mo
G
Batteries
Post Brackets
Transmitters
D
Pin Lock
3/8” Bushing (2)
2” Mounting Screw (5)
5/16” Washer (1)
3/8” Lock Washer (7)
X
3/8” x 1-1/2” Clevis Pin (2)
10
5/16” Washer (1)
S
R
Hairpin Clip (2)
5/16” x 1-3/4” Bolt (1)
O
N
Q
3/8” x 8” Bolt (4)
V
/
M
8” Nylon Cable Tie (14)
T
lt
Vo
Y
3/8” Nut (7)
3/8” Washer (9)
Z
5/16” Nut (1)
Before You Begin
Tools Needed
Marking
Pen
Long 3/8” Bit
5/16” Bit
Center
Punch
Drill
Pliers
Hack Saw
Hammer
1/2”
wrench
Flat Head
Screwdriver
9/16”
wrench
Level
Clamp
Philips Head
Screwdriver
Adjustable
Wrench
x2
Wire
Stripper
Small
Flat Head
Tape
Measure
Items Not Included
• Low voltage wire will be needed to run from the
transformer to the control box; length depends
upon the distance between the transformer power
supply and the control box. See Transformer Wiring
Installation on page 19, and the accessory catalog.
• Depending on the type of gate, a horizontal cross
member or mounting plate may be needed to mount
the front of the opener and gate bracket to the gate.
See Gate Bracket Mounting Examples in “Quick
Reference Guide” after Step 3 of “Mounting Opener
to Gate” section.
• PVC conduit.
• Surge protection for transformer.
• If your gate is more than 1000' away from an ac
power source you will need to use at least one GTO®
5 watt solar panel to trickle charge the battery. See
the accessory catalog (Do not use both transformer
and solar).
• Some types of installations require u-bolts.
• If the gate is a push-to-open refer to page 15 in
Installation Manual.
• Additional washers or a metal plate may be needed
for wooden post.
• If you have thin walled tube or panel gates, see
Recommended Reinforcement Examples in “Quick
Reference Guide” after Step 3 of “Mounting Opener
to Gate” section.
• Outlet in weatherproof cover.
• Strain relief nuts for accessory devices.
• If post is more than 6”, bolts longer than 8” are
needed.
11
Gate Opener Installation
Your Property
Mounting Pull-to-Open Opener to Gate
2
1
X
V
B
M
Q
I
H
X
I
S
R
M
Y
F
Q
Assemble post bracket parts.
Attach opener to gate bracket and secure with required
hardware.
3
Reinforcement and Gate Bracket Mounting
Muffler Clamp
(not supplied)
Gate
Bracket
Gate
Bracket
Thin Walled
Tube Gate
Wood or Metal
Reinforcement
(not supplied)
Mounting Plate Created for Decorative Gate
(required but not supplied)
Panel
Gate
Gate
Bracket
1” x 6” Wood Reinforcement
FRONT VIEW
With Gate in OPEN position, using clamps, secure opener to
gate post and center cross member of gate.
SIDE VIEW
Recommended reinforcement and gate bracket mounting
examples.
5
4
2" Min. - Pinch-Point Clearance
2
1
Top View
Closed
Position
2" Min.
2
1
Open
Position
Swing gate to CLOSED position-check clearance/binding by inspecting
alignment. TIP: Turning the pivot bracket over gives more hole
alignment options for the post pivot bracket assembly.
Remove clevis pin from the gate bracket and support loose
opener.
12
Gate Opener Installation
Your Property
Mounting Pull-to-Open Opener to Gate
7
6
2
U
O
1
N
Z
OPEN gate and reattach opener with clevis pin. Check for level.
Clamp securely.
Secure post pivot bracket to post bracket when clearance is OK
(Step 5) in both open and closed positions.
8
9
Mark middle of post bracket slots on fence post. Mark middle of
gate bracket slots on gate cross support.
Remove clamps, post, gate brackets, and opener. Then use a
hammer and center punch to mark hole positions.
11
10
Y
R
S
P
Drill 3/8” holes completely through gate post and gate cross
support.
Attach post bracket assembly to fence post. NOTE: Must be
through bolted.
13
Gate Opener Installation
Your Property
Mounting Pull-to-Open Opener to Gate
13
12
R
Y
2
1
S
T
1
2
Attach gate bracket assembly to gate cross support.
Attach and secure opener assembly to brackets.
14
15
Check for level. Adjust post bracket if necessary.
Remove bolt excess length on post and gate bracket with
hacksaw.
Closed Position Stop Plate Installation
1
2
1
J
1
2
Fully open gate. Attach gate stop with one of the following:
• U-bolts—tube and chain link gates (Not included)
• Wood/lag screws—flat aluminum/wood supports (Not included). Do not tighten.
Position gate stop with gate CLOSED to fence post. Tighten
fasteners. Cut off excess bolt length.
14
Gate Opener Installation
Your Property
Mounting Push-to-Open Opener to Gate
2
1
I
V
X
B
M
PTO
Bracket
347IH
Q
11”
X
I
S
Q
R
M
F
Y
Attach opener to gate bracket and secure with hardware required.
Assemble post bracket parts. NOTE: A Push-to-Open Bracket
347IH is required for this type of installation (not included).
3
Reinforcement and Gate Bracket Mounting
Muffler Clamp
(not supplied)
Gate
Bracket
Gate
Bracket
Thin Walled
Tube Gate
Wood or Metal
Reinforcement
(not supplied)
Mounting Plate Created for Decorative Gate
(required but not supplied)
Panel
Gate
Gate
Bracket
1” x 6” Wood Reinforcement
FRONT VIEW
SIDE VIEW
Recommended reinforcement and gate bracket mounting
examples.
With gate in CLOSED position, using clamps, secure opener to
gate post and center cross member of gate.
5
4
Top View
Recommend 11” to 19”
1
1
Open
Position
2" minimum
pinch-point clearance
2
Closed
Position
2
Swing gate to OPEN position. Check clearance/binding by inspecting the
alignment. Secure post pivot bracket to post bracket when clearance is OK
in both open and closed positions. TIP: Turning the pivot bracket over
gives more hole alignment options for the post pivot bracket assembly.
Remove clevis pin from the gate bracket and support loose
opener.
15
Push-to-Open Installation
Your Property
Mounting Push-to-Open Opener to Gate
7
6
2
U
1
O
N
Z
Secure post pivot bracket to post bracket when clearance is OK
(Step 5) in both open and closed positions.
CLOSE gate and reattach opener with clevis pin. Check for
level. Clamp securely.
8
9
Remove clamps, post, gate brackets, and opener. Then use a
hammer and center punch to mark hole positions.
Mark middle of post bracket slots on fence post. Mark middle of
gate bracket slots on gate cross support.
10
11
S
Y
R
P
Drill holes completely through gate post and gate cross support.
Attach post bracket assembly to fence post. NOTE: Must be
through bolted.
16
Push-to-Open Installation
Your Property
Mounting Push-to-Open Opener to Gate
13
12
R
1
Y
2
S
1
T
2
Attach gate bracket assembly to gate cross support.
Attach and secure opener assembly to brackets.
14
15
Check for level. Adjust post bracket if necessary.
Remove bolt excess length on post and gate bracket with
hacksaw.
Closed Position Stop Plate Installation
1
2
1
J
1
2
Fully open gate. Attach gate stop with one of the following:
• U-bolts—tube and chain link gates (Not included)
• Wood/lag screws—flat aluminum/wood supports (Not included). Do not tighten.
Position gate stop with gate CLOSED to fence post. Tighten
fasteners. Cut off excess bolt length.
17
Control Box Installation
Control Box Installation
6
7
AUTO CLOSE TIME
4
6
7
120 MIN
STALL FORCE
SOFT START OFF
WARNING OFF
OPEN
PULL
SLV OPEN DLY.
MODE1
OFF
MODE2
OFF
S3
S2
2
3
LEARN
SLV LIMIT
LEARN
MAST LIMIT
LEARN RMT
STATUS
MAX
ON
ON
PUSH
SIMULT.
ON
ON
FUSE
ON
4
AUTO CLOSE TIME
STALL FORCE
120 MIN
SOFT START OFF
WARNING OFF
OPEN
PULL
SLV OPEN DLY.
MODE1
OFF
MODE2
OFF
OFF
MASTER CABLE
3
7
2
6
1
5
4
D
BATT+
BATT-
4
ON
K
S3
S2
LEARN
SLV LIMIT
LEARN
MAST LIMIT
LEARN RMT
STATUS
MAX
CONTROL INPUTS
ON
ON
PUSH
SIMULT.
ON
ON
BL
OFF
15
3
G
OR
AUTO CLOSE TIME
PWR IN
CHARGING
2
SLAVE CABLE
RE
S4
RECEIVER
OW
RED
BLK
GTO RCVR.
ALM
AD
RECEIVER
E
OS
CLDGE
E
N
PE
OD
GE
E
SH
GR
BL
D
N
K
ALM
GTO RCVR.
RE
1
ALM
1
N
S4
GTO RCVR.
AUX
GR
RECEIVER
GTO
LOCK
M
CO
AUX
RLY
OS
CL GE
ED
EN
OPGE
ED
PWR
M
CO
E
CL
CY
TY
FE
SA
IT
EX
LOCK
N
CONTROL
INPUTS
18 VAC
or
SOLAR
N
CONTROL INPUTS
GTO
TRANSF
U
BL
POWER
INPUTS
BR
MASTER CABLE
S4
T
WH
NE
Red
PO
G
S
OR
BATT+
5
S2
1
2
3
LEARN
SLV LIMIT
ALM
GR
RED
ON
4
GTO RCVR.
N
BATT-
4
S3
LEARN
MAST LIMIT
LEARN RMT
STATUS
MAX
ON
ON
PUSH
SIMULT.
ON
ON
RECEIVER
RE
D
3
120 MIN
STALL FORCE
SOFT START OFF
WARNING OFF
OPEN
PULL
SLV OPEN DLY.
MODE1
OFF
MODE2
OFF
OFF
CONTROL INPUTS
BR
G
OR
15
2
BLK
AUTO CLOSE TIME
MASTER CABLE
U
BL
SLAVE CABLE
7
EXIT
FUSE
1
6
T
PWR IN
AUX
5
COM
CHARGING
GTO
LOCK
4
N
T
WH
AUX
RLY
BATT+
BATT-
3
GRN
BLK
PWR
2
SLAVE CABLE
OW
AD
SH
E
6”
GR
2
BLK
RED
LOCK
1
RED
BLK
CONTROL
INPUTS
18 VAC
or
SOLAR
AUX
ORG
RED
1
GTO
TRANSF
15
FUSE
PWR IN
CHARGING
GTO
LOCK
18
AUX
RLY
Feed cable 6” into box. Tighten strain relief nut to secure cable.
Twist each end of the gate opener power cable’s 7 colored wires.
Feed cable through strain relief nut.
PWR
Position batteries in control box as shown. Connect battery leads
from control board to batteries. IMPORTANT: Red wire to (Red
Post) positive and black wire to (Black Post) negative.
Mount control box to post or fence using screws.
BRN
ORG
Bla
GRN
BLU
BRN
ck
EXIT
SE
CLO E
EDG
N
OPE E
EDG
SE
CLO E
EDG
N
OPE E
EDG
BLK
W
DOW
SHA
DOW
SHA
W
ORG
RED
COM
COM
BRN
ORG
LE
CYC
ETY
SAF
LE
CYC
ETY
SAF
BLU
BRN
LOCK
T
RED
BLK
GRN
WH
CONTROL
INPUTS
18 VAC
or
SOLAR
COM
WH
BLU
3’
POWER
INPUTS
GTO
TRANSF
BLU
POWER
INPUTS
GRN
GRN
T
WH
GRN
T
WH
Am
pM
3
7.0
S4
ALM
ON
3
4
GTO RCVR.
Locate control box mounting area. IMPORTANT: Be sure to
mount box at least 3 feet from AC power and 3 feet off the ground.
Remove control box cover.
/
S2
LEARN
SLV LIMIT
RECEIVER
BLK
lt
Vo
S3
LEARN
MAST LIMIT
LEARN RMT
STATUS
MAX
ON
ON
PUSH
SIMULT.
ON
ON
CONTROL INPUTS
RED
12
STALL FORCE
120 MIN
SOFT START OFF
WARNING OFF
OPEN
PULL
SLV OPEN DLY.
MODE1
OFF
MODE2
OFF
OFF
MASTER CABLE
DOW
2
5
BLK
BATT+
4
GRN
BATT-
3
SE
CLO E
EDG
EN
OP E
EDG
SHA
15
2
T
SLAVE CABLE
RED
FUSE
1
BRN
G
OR
PWR IN
AUX
WH
CHARGING
GTO
LOCK
COM
AUX
RLY
COM
PWR
BLU
n.
i
M
3’
n.
i
M
LE
CYC
ETY
SAF
T
EXI
LOCK
GRN
CONTROL
INPUTS
G
OR
6
B
5
18 VAC
or
SOLAR
BLU
1
GTO
TRANSF
GRN
T
WH
POWER
INPUTS
A
4’
x.
a
M
2
1
BRN
RED
BLK
G
NE
PO
G
S
BL
K
3
RB
500
ou
nt
Control Box Installation
Control Box Installation
AUX
RLY
8
1
7
GRN
5
ORG
6
GRN
7
WHT
MASTER CABLE
RED
PWR IN
4
BRN
2ND OPERATOR
3
BLU
CHARGING
2
WHT
BLK
BLU
GRN
MASTER OPERATOR
WHT
BLU
BRN
ORG
GRN
RED
BRN
ORG
BLK
BRN
ORG
COM
CYCLE
SAFETY
EXIT
SHADOW
CLOSE
EDGE
OPEN
EDGE
BLK
COM
Correct
S4
CONTROL INPUTS
RED
ALM
BLK
LEARN
2nd LIMIT
BLK
Wrong
Wrong
COM
GRN
RECEIVER
GTO RCVR.
RED
RED
COM
CONTROL INPUTS
BLU
MASTER OPERATOR
WHT
CYCLE
SAFETY
Insert 7 wires into corresponding color terminals.
Wire
Terminal
Block
Screwed into
wire insulation
Secure wires in terminals.
Exposed strands
of wire
If using optional solar panel charger instead of transformer, go to page 22.
IMPORTANT: Do not connect both solar panel and transformer.
Transformer Wiring Installation
9
10
Top View
Min 3 Ft
Max 1,000 Ft
GTO Transformer
Mounts Here
CAUTION: Please
call your power company
before you dig. Failure to
do so could cause injury
or even death.
Locate power outlet and identify wire path to control box.
NOTE: If OUTLET is OUTSIDE use weatherproof cover.
Dig trench and lay wire from AC power source to control box.
Use only 16 guage stranded, low voltage, PVC sheathed wire
(RB509). NOTE: DO NOT use telephone wire or solid core wire.
NEVER splice wires together.
19
Control Box Installation
Transformer Wiring Installation
11
12
C
1
1
2
Use PVC conduit from ground up to control box to protect the
wire from lawn mowers and grazing animals.
Strip 1/2” off 2 wires and twist ends. Attach wires to transformer
screw terminals.
14
13
GTO
TRANSF
POWER
INPUTS
15
FUSE
PWR IN
GTO
LOCK
AUX
RLY
CHARGING
PWR
LOCK
CONTROL
INPUTS
18 VAC
or
SOLAR
AUX
1
7
RE
K
BL
1
2
3
4
ON
AUX
RLY
S2
LEARN
SLV LIMIT
S3
LEARN
MAST LIMIT
LEARN RMT
STATUS
OW
S4
AD
MAX
ON
ON
PUSH
SIMULT.
ON
ON
IT
EX
CONTROL INPUTS
M
CO
M
CO
E
CL
CY
TY
FE
SA
LOCK
PWR
K
BL
SH
GRN
RED
MASTER OPERATOR
ORG
BLK
BLK
ON
SURGE PROTECTOR
Wrong
Wrong
4
5
6
SLAVE CABLE
3
7
Screwed into
wire insulation
Exposed strands
of wire
Plug in transformer to power outlet. (Use of a surge protector is
highly recommended. If outdoors use weatherproof box.)
Secure with terminal screws.
GRN
BRN
20
PWR IN
7
AUX
RLY
CONTROL OUTPUTS
LOCK
PWR
2
Terminal
Block
BLK
BLU
16
POWER
INPUTS
1
RED
Wire
6
AUX
RLY
ALM
GTO 18VOLT
TRANSF. OR
SOLAR PANEL
ORG
WHT
Insert one wire into each 18VAC terminal. Colors do not matter.
GRN
BRN
GRN
COM
Feed other end of low voltage wire 10” into box through
the hole.
BLU
5
D
Correct
WHT
4
B
RE
CONTROL OUTPUTS
LOCK
PWR
LK
15
RED
S2
S4
N
GR
ORG
BLK
RECEIVER
E
OS
CLDGE
E
N
PE
OD
GE
E
BRN
2ND OPERATOR
3
POWER
INPUT
LEARN RMT
STATUS
GTO 18VOLT
TRANSF. OR
SOLAR PANEL
BLU
CHARGING
2
WHT
S3
OW
AD
SH
LEARN
MAST LIMIT
LEARN
SLV LIMIT
E
CL
CY
TY
FE
SA
MAX
ON
ON
PUSH
SIMULT.
ON
ON
CONTROL INPUTS
10”
1
BLK
RED
ALM
GTO RCVR.
N
GR
STALL FORCE
RECEIVER
E
OS
CL GE
ED
EN
OPGE
ED
CONTROL OUTPUTS
STALL FORCE
D
RE
120 MIN
G
OR
AUTO CLOSE TIME
N
BR
SOFT START OFF
WARNING OFF
OPEN
PULL
SLV OPEN DLY.
MODE1
OFF
MODE2
OFF
T
WH
U
BL
OFF
MASTER CABLE
N
GR
POWER
INPUT
6
GTO 18VOLT
TRANSF. OR
SOLAR PANEL
5
D
BR
BATT+
N
G
OR
BATT-
4
3
2
U
BL
SECOND CABLE
N
GR
T
WH
Control Box Installation
Receiver Installation
2
1
W
W
’
10
x
Ma
Check Receiver reception before permanently securing to fence
or post. NOTE: If mounting on metal fence, mount receiver on a
piece of wood. DO NOT mount upside down.
Install Receiver within 10 ft of control box (longer lengths available - call us). NOTE: NEVER splice receiver cable. DO NOT
run cable through conduit containing AC wire. DO NOT place
receiver within 3 feet of AC power.
Use the transmitter to check the range of the receiver before permanently mounting it.
Consider the following when mounting the receiver:
• Standard receiver cable length is 10 feet (receivers with a longer cable are available as special
order items; call the GTO Sales Department). NEVER splice receiver cable!
• Run the cable through PVC conduit to protect it from damage.
• DO NOT run cable through conduit containing AC wire.
• DO NOT place receiver within 3 feet of AC power.
• DO NOT coil excess cable or store it in the control box.
• Do not mount upside down.
• The receiver range can vary depending upon weather, topography, and external interference.
Tips
FCC Regulation
1. Mount the receiver high and above any obstructions; fence
pickets, column caps, etc.
This device complies with FCC rules Part 15.
Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that
may cause undesired operation.
2. If radio control seems limited try moving the receiver 1-2 feet
in each direction to reduce radio noise “dead spots.”
Transmitter distance may vary due to circumstances
beyond our control. NOTE: The manufacturer is
not responsible for any radio or TV interference
caused by unauthorized modifications to
this equipment. Such modifications could
void the user’s authority to operate
the equipment.
21
Solar Panel Installation
(Optional)
The table and map illustrate the
maximum number of gate cycles to
expect per day in a particular area
when using from 5 to 30 watts of
solar charging power. (see accessory
pages in back of this book). The
figures shown are for winter
(minimum sunlight) and do not account for the use of
any accessory items. Accessories connected to your
system will draw additional power from the battery.
Winter Ratings
Zone 1
12 v single gate ( 5 watts) solar charger
12 v single gate (10 watts) solar charger
12 v single gate (15 watts) solar charger
12 v single gate (20 watts) solar charger
12 v single gate (25 watts) solar charger
12 v single gate (30 watts) solar charger
4
8
11
14
17
20
Zone 2
Zone 3
8
16
20
28
36
44
13
26
30
38
46
54
NOTE: A minimum of 5 watts of solar charging power
is required for GTO single gate opener systems, with
a maximum of 30 watts. Consult Solar Panel Installation
Instructions for further information.
2
1
Toward
Equator
The solar panel must be positioned facing the path of the sun
and in an open area away from shade. It should receive at least 8
hours of direct sunlight for a full charge.
Feed wire from solar panel through hole in knockout in
control box.
IMPORTANT: Mount the panel using
the curved pipe provided to maintain
the proper angle to the sun.
IMPORTANT: Requires 8 hours
of direct sunlight a day.
22
Solar Panel Installation
15
FUSE
BATT+
BATT-
AUX
RLY
CONTROL
OUTPUTS
LOCK
PWR
1
5
6
7
MASTER OPERATOR
LOCK
PWR
AUX
RLY
BLK
CONTROL OUTPUTS
S4
2
3
AUX
RLY
CONTROL OUTPUTS
LOCK
PWR
1
ON
2
3
4
ON
4
5
SLAVE CABLE
Exposed strands
of wire
Secure with terminal screws.
Multiple Panel Installations
attach wires to POWER INPUT terminals marked
“GTO 18VOLT TRANSF. OR SOLAR PANEL” on the control board.
(wire color does not matter on this terminal connection)
PWR IN
4
2ND OPERATOR
3
POWER
INPUT
GTO 18VOLT
TRANSF. OR
SOLAR PANEL
S3
LEARN
MAST LIMIT
LEARN RMT
STATUS
MAX
BLK
CHARGING
2
STALL FORCE
120 MIN
LEARN
SLV LIMIT
S2
ORG
D
RE
BLU
ON
ON
PUSH
SIMULT.
ON
ON
POWER
INPUT
4
23
RED
ALM
3
BLACK
BLACK
WHT
RECEIVER
K
RED
CONTROL INPUTS
2
RED
RED
BRN
BL
POWER
INPUT
GTO 18VOLT
TRANSF. OR
SOLAR PANEL
AUTO CLOSE TIME
OFF
SOFT START OFF
WARNING OFF
OPEN
PULL
SLV OPEN DLY.
MODE1
OFF
MODE2
OFF
STATUS
S4
1
PWR IN
STALL FORCE
S2
LEARN
SLV LIMIT
1
BRN
Solar Panels connect in PARALLEL
NOTE: All connections should be
weatherproofed using weatherproof
splice kits available at hardware and
electrical supply stores.
CHARGING
AUTO CLOSE TIME
S3
LEARN
MAST LIMIT
LEARN RMT
ON
ON
PUSH
SIMULT.
ON
ON
MAX
MASTER CABLE
120 MIN
SOFT START OFF
WARNING OFF
OPEN
PULL
SLV OPEN DLY.
MODE1
OFF
MODE2
OFF
OFF
N
GTO RCVR.
Insert RED and BLACK wires into the power teerminals.
NOTE: colors do not matter in this terminal.
Feed cable 10” into box.
BLU
GR
BLK
IT
FUSE
7
ALM
GTO RCVR.
EX
GRN
E
OS
CLDGE
E
N
PE
OD
GE
E
ORG
M
CO
E
CL
CY
TY
FE
SA
CONTROL
INPUTS
6
RECEIVER
OW
AD
SH
LOCK
5
CONTROL INPUTS
RE
BRN
M
CO
GRN
D
RED
BATT-
MASTER CABLE
WHT
WHT BLUE
BRN
4
7
BLK
3
6
D
Wrong
GRN
BLU
BR
PWR IN
5
OW
CHARGING
4
N
K
2
3
GR
BL
BATT+
15 CABLE
SLAVE
2
SECOND CABLE
RE
WHT
K
BL
10”
1
1
IT
AUX
AUX
K
BL
AUX
RLY
GTO
LOCK
GTO
LOCK
M
T
AUX
RLY
EX
G
OR
N
GR
T
CO
N
AD
SH
E
OS
CL GE
ED
EN
OPGE
ED
WH
M
CO
E
CL
CY
TY
FE
PWR
N
BR
G
OR
LOCK
T
CONTROL
INPUTS
D
N
18 VAC
or
SOLAR
BR
Screwed into
wire insulation
Terminal
ORG
Block
Wire
G
OR
GR
Wrong
GRN
Correct
N
PWR
18 VAC
or
SOLAR
GTO
TRANSF
GTO 18VOLT
TRANSF. OR
SOLAR PANEL
5
U
BL
U
BL
SA
RE
N
D
T
POWER
INPUTS
WH
G
OR
N
BL
U
BL
N
BR
WH
K
GR
U
BL
RE
WH
GR
4
3
Control Box Settings
DIP Switches
IMPORTANT: Before making any changes to DIP switches turn control box off!
DIP#1
ON**___Soft start enabled (factory preset).
OFF __Soft start disabled.
GTO
TRANSF
POWER
INPUTS
DIP#2
ON**___Buzzer warning enabled (factory preset).
OFF __ Buzzer warning disabled.
15
FUSE
PWR IN
GTO
LOCK
AUX
RLY
CHARGING
PWR
LOCK
CONTROL
INPUTS
18 VAC
or
SOLAR
AUX
1
4
BATT+
3
5
BRN
BATT-
2
BLU
SECOND CABLE
N
T
WH
GR
6
G
OR
7
RED
BLK
2
3
4
ON
S2
LEARN
SLV LIMIT
S4
RECEIVER
GRN
BLK
RED
ALM
GTO RCVR.
DIP#3
ON*___Push-to-open.
OFF*__Pull-to-open (factory preset).
S3
LEARN
MAST LIMIT
LEARN RMT
DOW
STATUS
T
EXI
SHA
SE
CLO E
EDG
EN
OP E
EDG
MAX
LE
CYC
ETY
CONTROL INPUTS
M
CO
ON
ON
PUSH
SIMULT.
ON
ON
BLK
SAF
1
RED
STALL FORCE
G
OR
120 MIN
BRN
AUTO CLOSE TIME
BLU
SOFT START OFF
WARNING OFF
OPEN
PULL
SLV OPEN DLY.
MODE1
OFF
MODE2
OFF
T
WH
OFF
MASTER CABLE
N
GR
M
CO
1 2 3 4
ON
1 2 3 4
DIP#4
NOTE: Not applicable for single gate operator.
*factory
presets shown
DIP Switch #4 Not applicable for single gate operator.
DIP Switch #1 - Soft Start/Stop
The soft start/stop feature slowly starts the gate as it
begins to open or close and slows the gate as it comes
to the opened or closed position. This saves wear and
tear on the gate and gate opener system.
DIP Switch #2 - Warning Buzzer
The warning buzzer alerts you when the gate opener
is beginning to either open or close the gate. It sounds
for the first 2 seconds in each direction. It also sounds
a warning when the gate obstructs two times in one
cycle. Switching this to OFF only disables the open
and close warning not the obstruction warning.
DIP Switch #3 - Push/Pull-to-Open
If your gate opens into the property the DIP Switch is
set to the OFF position (factory setting). If your gate
opens out from the property the DIP Switch must be
set to the ON position. NOTE: if you have a Push-toOpen gate application you will need a Push-to-Open
bracket (see Push-to-Open Instructions on page 16).
24
1515
FUSE
FUSE
2
BATT+
BATT+
BATTBATT-
6
7
7
OFFOFF
120120MINMIN
SOFT
START
OFFOFF
SOFT
START
WARNING
WARNING OFFOFF
OPEN
PULL
OPEN
PULL
SLVSLV
OPEN
OPENDLY.DLY.
MODE1
OFFOFF
MODE1
MODE2
OFFOFF
MODE2
AUTO
CLOSE
TIME
FORCE
AUTO
CLOSE
TIME STALL
STALL
FORCE
MASTER
CABLE
MASTER
CABLE
STATUS
STATUS
RECEIVER
RECEIVER
S4S4
LEARN
LEARN
SLVLIMIT
LIMIT
SLV
ON
LEARN
RMT
LEARN
RMT
MAX
MAX
S3S3
ONON
ONON
LEARN
LEARN
PUSH
PUSH
MASTLIMIT
LIMIT
SIMULT.
SIMULT.MAST
ONON
S2S2
ONON
CONTROLINPUTS
INPUTS
CONTROL
RED
RED
BLK
BLK
ALM
ALM
ON
4
3
2 4
1 3
2
1
GTO RCVR.
RCVR.
GTO
BATT+
BATT+
BATTBATT-
4
5
5
6
6
7
7
120120MINMIN
SOFTSOFT
START
OFFOFF
START
WARNING
WARNINGOFFOFF
OPEN
PULL
OPEN
PULL
SLV SLV
OPEN
DLY.DLY.
OPEN
MODE1
MODE1 OFFOFF
MODE2
MODE2 OFFOFF
OFF OFF
S3
STATUS
STATUS
ON
1 2 3 4
CONTROL
INPUTS
CONTROL
INPUTS
RECEIVER
RECEIVER
S4S4
LEARN
LEARN
LIMIT
SLVSLVLIMIT
LEARN
RMT
LEARN
RMT
MAX
MAX
S3S3
ON ON
ON ON
LEARN
LEARN
PUSH
PUSH
LIMIT
MAST
LIMIT
SIMULT.
SIMULT.MAST
ONON
S2S2
ONON
AUTO
CLOSE
TIME
FORCE
AUTO
CLOSE
TIMESTALL
STALL
FORCE
MASTER
CABLE
MASTER
CABLE
ON
3
4
ON
4
3
2
1 3 4
2
1
2
3
ALM
ALM
GTORCVR.
RCVR.
GTO
S2
ON
ON
Press button on opener remote; gate should start closing. Press button
on opener remote again when gate is in desired CLOSED position.
With gate in OPEN position, turn control box power ON.
4
3
1
S4
Press button on transmitter to fully open gate. Closed limit is set
upon reaching fully open position. Test and, if needed, reset and
start over.
Press and hold the “ LEARN MAST LIMIT” button for 5 seconds,
or until the alarm sounds.
6
5
1515
FUSE
FUSE
BATT+
BATT+
BATTBATT-
6
7
7
120120MINMIN
SOFT
START
SOFT
START
OFFOFF
WARNINGOFFOFF
WARNING
OPEN
PULL
OPEN
PULL
OPENDLY.DLY.
SLVSLV
OPEN
MODE1
MODE1
OFFOFF
MODE2
MODE2
OFFOFF
OFFOFF
AUTO
CLOSE
TIME
FORCE
AUTO
CLOSE
TIME STALL
STALL
FORCE
MASTER
CABLE
MASTER
CABLE
STATUS
STATUS
S3S3
LEARN
RMT
LEARN
RMT
MAX
MAX
ON
1 2 3 4
LEARN
LEARN
SLVLIMIT
LIMIT
SLV
ONON
ONON
LEARN
LEARN
PUSH
PUSH
MAST
LIMIT
LIMIT
SIMULT.MAST
SIMULT.
ONON
S2S2
ONON
S4S4
RECEIVER
RECEIVER
ALM
ALM
GTO RCVR.
GTO RCVR.
S2
ON
ON
OFF
OFF
MODE1
MODE2
S3
CONTROL
INPUTS
CONTROL
INPUTS
25
5
6
Press and hold the “LEARN MAST LIMIT” button for
10 seconds, or until the alarm sounds to clear. Go back to the
setting closed limit steps on the top of this page.
Press button on transmitter to open gate.
PWR IN
PWR IN
5
S4
1
4
RED
RED
MAX
MIN
120
LEARN
MAST LIMIT
GRN
GRN
BLK
BLK
CHARGING
CHARGING
3
4
BLK
ON
ON
PUSH
SIMULT.
CLO SE
EDG
CLON E
EDG
OPE E N
EDG
OPE E
EDG
OFF
BRN
ORG
ORG
RED
RED
BLK
BLK
2
2
3
BLU
BRN
OFF
OFF
PULL
DLY.
DOW
SHA DOW
SE
SHA E
LEARN RMT
WHT
BLU
SECOND
CABLE
SLAVE
CABLE
1
2
GRN
WHT
1
GRN
RLYRLY
GTO
AUX
GTO
AUX
LOCK
LOCK
ORG
RED
SOFT START
WARNING
OPEN
SLV OPEN
COM
COM
COM
COM
LE
CYC LE
CYC
ETY
SAF ETY
SAF
EXIT
EXIT
PWR
BRN
ORG
LOCKLOCK
AUXAUX
PWR
18 VAC
18 VAC or
or SOLAR
SOLAR
BLU
BRN
GTO
WHT
BLU
GTO TRANSF
TRANSF
GRN
WHT
POWER
CONTROL
POWER
INPUTS CONTROL
INPUTS
INPUTS
INPUTS
GRN
3
1
ON
ON
1
(for push-to-open go to pg. 27)
Setting Closed Gate Limit (Pull-To-Open)
ON
4
3
2
4
1
3
2
1
PWR IN
PWR IN
CHARGING
CHARGING
5
6
15 15
FUSEFUSE
PWR IN
PWR IN
CHARGING
CHARGING
1
2
SECOND
CABLE
SLAVE
CABLE
RED
RED
MAX
MIN
LEARN
MAST LIMIT
GRN
GRN
BLK
BLK
120
COM
COM
COM
OFF
OFF
MODE1
MODE2
2
CLO SE
EDG
CLON E
EDG
OPE EN
EDG
OPE E
EDG
5
BLK
ON
ON
PUSH
SIMULT.
COM
LE
CYC LE
CYC
ETY
SAF ETY
SAFT
EXI T
EXI
1
BLK
OFF
OFF
PULL
DLY.
SOFT START
WARNING
OPEN
SLV OPEN
DOW
SHA DOW
SHASE
E
OFF
BLU
BRN
BRN
ORG
ORG
RED
RED
BLK
BLK
RLY RLY
GTO
AUX
GTO
AUX
LOCK
LOCK
T
GRN
WH
T
WH
BLU
PWR
GRN
LOCKLOCK
AUXAUX
PWR
18 VAC
18 VAC or
or SOLAR
SOLAR
ORG
RED
GTO
BRN
ORG
GTO TRANSF
TRANSF
BLU
BRN
POWER CONTROL
CONTROL
POWER
INPUTS INPUTS
INPUTS
INPUTS
GRN
T
GRN
WH
T
WH
BLU
4
GRN
GRN
3
4
COM
COM
COM
3
COM
LE
CYC LE
2
CLO SE
EDG
CLON E
EDG
OPE EN
OPE E
EDG
EDG
SECOND
CABLE
SLAVE
CABLE
1
2
CYC
ETY
SAF ETY
SAFT
EXI T
EXI
1
DOW
SHA DOW
SHASE
E
RLYRLY
GTO
AUX
GTO
AUX
LOCK
LOCK
BLU
BLU
BRN
BRN
ORG
ORG
RED
RED
BLK
BLK
PWR
GRN
GRN
T
WH
T
WH
LOCKLOCK
AUXAUX
PWR
18 VAC
18 VAC or
or SOLAR
SOLAR
ORG
RED
GTO
BRN
ORG
GTO TRANSF
TRANSF
BLU
BRN
POWER CONTROL
CONTROL
POWER
INPUTS
INPUTS
INPUTS
INPUTS
GRN
T
GRN
WH
T
WH
BLU
2
Control Box Settings
RED
BLK
NOTE: If your gate obstructs before it fully closes, you may
need to increase the stall force. (See page 28)
RED
BLK
LEARN
2nd LIMIT
Resetting Closed Gate Limit
RED
BLK
LEARN
2nd LIMIT
1515
FUSE
FUSE
BATT+
BATT+
2
4
7
7
6
6
5
5
AUTO
CLOSE
TIME
AUTO
CLOSE
TIME STALL
STALLFORCE
FORCE
OFFOFF
120120MIN
MIN
SOFT
START
OFFOFF
SOFT
START
WARNING
WARNING OFFOFF
OPEN
PULL
OPEN
PULL
SLVSLVOPEN
OPENDLY.
DLY.
MODE1
OFF
MODE1
OFF
MODE2
OFF
MODE2
OFF
MASTER
CABLE
MASTER
CABLE
STATUS
STATUS
CONTROLINPUTS
INPUTS
CONTROL
S4S4
LEARN
LEARN
SLV LIMIT
LIMIT
SLV
LEARN
LEARNRMT
RMT
MAX
MAX
S3S3
ONON
ONON
LEARN
LEARN
PUSH
PUSH
MASTLIMIT
LIMIT
SIMULT.
SIMULT. MAST
ONON
S2S2
ONON
ON
4
ON
4
3
2
1 3 4
2
1
3
RECEIVER
RECEIVER
RED
RED
BLK
BLK
ALM
ALM
GTO RCVR.
RCVR.
GTO
1
ON
4
3
BATT+
BATT+
BATTBATT-
5
5
6
6
7
7
2
STATUS
STATUS
ON
1 2 3 4
CONTROL
INPUTS
CONTROL
INPUTS
RECEIVER
RECEIVER
S4S4
LEARN
LEARN
SLVLIMIT
LIMIT
SLV
LEARN
RMT
LEARN
RMT
MAX
MAX
S3S3
ONON
ONON
LEARN
LEARN
PUSH
PUSH
MASTLIMIT
LIMIT
SIMULT.
SIMULT.MAST
ONON
S2S2
ONON
AUTO
CLOSE
TIME
FORCE
AUTO
CLOSE
TIME STALL
STALL
FORCE
OFFOFF
120120MINMIN
SOFT
START
OFFOFF
SOFT
START
WARNING
WARNINGOFFOFF
OPEN
PULL
OPEN
PULL
SLVSLV
OPEN
OPENDLY.DLY.
MODE1
OFFOFF
MODE1
MODE2
OFFOFF
MODE2
MASTER
CABLE
MASTER
CABLE
ON
4
ON
4
3
2
1 3 4
2
1
3
4
S3
MAX
MIN
ALM
ALM
GTO RCVR.
RCVR.
GTO
S2
ON
ON
Press button on transmitter to fully close gate. Open limit is set
upon reaching the fully closed limit. Test and, if needed reset
and start over.
Press and hold the “LEARN MASTER LIMIT” button for 5
seconds, or until the alrm sounds.
6
5
1
S4
1515
FUSE
FUSE
BATT+
BATT+
BATTBATT-
5
6
6
7
7
120120MINMIN
SOFT
START
SOFT
START
OFFOFF
WARNINGOFFOFF
WARNING
OPEN
PULL
OPEN
PULL
OPENDLY.DLY.
SLVSLV
OPEN
MODE1
MODE1
OFFOFF
MODE2
MODE2
OFFOFF
OFFOFF
AUTO
CLOSE
TIME
FORCE
AUTO
CLOSE
TIME STALL
STALL
FORCE
MASTER
CABLE
MASTER
CABLE
STATUS
STATUS
S3S3
LEARN
RMT
LEARN
RMT
MAX
MAX
ON
1 2 3 4
S4S4
LEARN
LEARN
SLVLIMIT
LIMIT
SLV
ONON
ONON
LEARN
LEARN
PUSH
PUSH
MAST
LIMIT
LIMIT
SIMULT.MAST
SIMULT.
ONON
S2S2
ONON
RECEIVER
RECEIVER
ALM
ALM
GTO RCVR.
GTO RCVR.
S2
ON
ON
OFF
OFF
MODE1
MODE2
S3
CONTROL
INPUTS
CONTROL
INPUTS
26
Hold the “LEARN MASTER LIMIT” button for 10 seconds,
or until the alarm sounds to clear. Go back to setting open gate
limit step 1 at the top of this page.
Press button on transmitter to close gate.
PWR IN
PWR IN
5
RED
RED
MAX
MIN
120
LEARN
MAST LIMIT
GRN
GRN
BLK
BLK
4
BLK
ON
ON
PUSH
SIMULT.
CLO SE
EDG
CLON E
EDG
OPE E N
EDG
OPE E
EDG
CHARGING
CHARGING
3
4
BLU
BRN
OFF
OFF
PULL
DLY.
DOW
OW
SHA
SE
SHADE
LEARN RMT
WHT
BLU
OFF
BRN
ORG
ORG
RED
RED
BLK
BLK
2
S4
1
2
3
GRN
WHT
SECOND
CABLE
SLAVE
CABLE
1
2
GRN
1
GRN
WHT
SOFT START
WARNING
OPEN
SLV OPEN
COM
COM
COM
COM
LE
CYC LE
CYC
ETY
SAF ETY
SAF
EXIT
EXIT
RLYRLY
GTO
AUX
GTO
AUX
LOCK
LOCK
ORG
RED
PWR
BRN
ORG
LOCKLOCK
AUXAUX
PWR
18 VAC
18 VAC or
or SOLAR
SOLAR
BLU
BRN
GTO
WHT
BLU
GTO TRANSF
TRANSF
GRN
POWER
CONTROL
POWER
INPUTS CONTROL
INPUTS
INPUTS
INPUTS
3
Press button on opener remote; gate should start opening. Press button on opener remote again when gate is in desired OPEN position.
NOTE: If your gate obstructs before it fully closes, you may
need to increase the stall force. (See page 28)
With gate in CLOSED position, turn control box power switch
to ON.
ON
1
(for pull-to-open go to pg. 26)
Setting Open Gate Limit (Push-To-Open)
ON
4
3
2
4
1
3
2
1
BATTBATT-
3
GRN
GRN
PWR PWR
IN IN
2
CLO SE
EDG
CLONE
EDG
OPE EN
OPE E
EDG
EDG
CHARGING
CHARGING
2
SECOND
CABLE
SLAVE
CABLE
1
DOW
SHA DOW
SHASE
E
OFF
OFF
MODE1
MODE2
1
1515
FUSE
FUSE
PWR IN
PWR IN
CHARGING
CHARGING
2
3
RED
RED
RLYRLY
GTO
AUX
GTO
AUX
LOCK
LOCK
BLK
LEARN
MAST LIMIT
GRN
GRN
BLK
BLK
PWR
COM
COM
COM
COM
LE
CYC LE
LOCKAUX
AUX
LOCK
PWR
18 VAC
18 VAC or
or SOLAR
SOLAR
CYC
ETY
SAF ETY
SAFT
EXI T
EXI
GTO
BLU
BLU
BRN
BRN
ORG
ORG
RED
RED
BLK
BLK
GTOTRANSF
TRANSF
GRN
GRN
T
WH
T
WH
120
COM
COM
COM
SECOND
CABLE
SLAVE
CABLE
1
2
CLO SE
EDG
CLONE
EDG
OPE EN
EDG
OPE E
EDG
ORG
RED
ON
ON
PUSH
SIMULT.
COM
LE
CYC LE
CYC
ETY
SAF ETY
SAFT
EXI T
EXI
1
BLK
BRN
ORG
OFF
OFF
PULL
DLY.
SOFT START
WARNING
OPEN
SLV OPEN
DOW
SHA DOW
SHASE
E
OFF
BLU
BRN
G
BRN
OR
ORG
RED
RED
BLK
BLK
RLYRLY
GTO
AUX
GTO
AUX
LOCK
LOCK
T
GRN
WH
T
WH
BLU
PWR
GRN
LOCKLOCK
AUXAUX
PWR
18 VAC
18 VAC or
or SOLAR
SOLAR
ORG
RED
GTO
G
BRN
OR
GTO TRANSF
TRANSF
BLU
BRN
POWER CONTROL
CONTROL
POWER
INPUTS
INPUTS
INPUTS
INPUTS
GRN
T
GRN
WH
T
WH
BLU
BLU
BRN
3
POWER CONTROL
CONTROL
POWER
INPUTS
INPUTS
INPUTS
INPUTS
GRN
T
GRN
WH
T
WH
BLU
2
Control Box Settings
RED
BLK
RED
BLK
LEARN
2nd LIMIT
Resetting Open Gate Limit
RED
BLK
LEARN
2nd LIMIT
Control Box Settings
Setting Obstruction Stall Force & Auto Close Time
1
2
FUSE
FUSE
1515
4
5
BATT+
BATT+
3
4
BATTBATT-
2
3
5
6
6
G
BRN
OR
SECOND
CABLE
SLAVE
CABLE
1
2
BLU
BRN
PWR IN
PWR IN
1
GRN
T
GRN
WH
T
WH
BLU
CHARGING
CHARGING
RLYRLY
GTO
AUX
GTO
AUX
LOCK
LOCK
7
ORG
RED
7
RED
BLK
4
ON
3
2
1 3 4
2
1
RED
BLK
BLK
ON
STATUS
STATUS
S4S4
LEARN
LEARN
LIMIT
SLVSLVLIMIT
S3S3
LEARN
RMT
LEARN
RMT
MAX
MAX
ON ON
ONON
LEARN
LEARN
PUSH
PUSH
MAST
LIMIT
LIMIT
SIMULT.MAST
SIMULT.
ONON
S2S2
ONON
AUTO CLOSE TIME
120
OFF
OFF
PULL
DLY.
STALL FORCE
MIN
1
2
1
3
3
ON
2
4
4
ON
1 2 3 4
ON
1 2 3 4
STATUS
LEARN RMT
LEARN
MAST LIMIT
LEARN
SLV LIMIT
Turn the “STALL FORCE” arrow in the center of the potentiometer with small flat head screwdriver. Adjust the sensitivity from the
MINIMUM position up to the point where the gate operates without
obstructing from its own weight or the wind conditions in your area.
OFF
SOFT START
WARNING
OPEN
SLV OPEN
MAX
ON
ON
PUSH
SIMULT.
ON
ON
OFF
OFF
STALL FORCE
MIN
MODE1
MODE2
ALM
ALM
GTO RCVR.
GTO RCVR.
GRN
GRN
BLK
BLK
RED
RED
RECEIVER
RECEIVER
EDG SE
E
CLO
EN
EDG
EN
OP
EDG
OPE E
EDG
CONTROL
INPUTS
CONTROL
INPUTS
COM
COM
COM
COM
LE
CYC LE
CYC
ETY
SAF ETY
SAFT
EXI T
EXI
DOW
SHA DOW
SE
SHA E
CLO
120120MINMIN
SOFT
START
OFFOFF
SOFT
START
WARNINGOFFOFF
WARNING
OPEN
PULL
OPEN
PULL
OPENDLY.DLY.
SLV SLV
OPEN
MODE1
MODE1
OFFOFF
MODE2
MODE2
OFFOFF
BLU
BRN
G
BRN
OR
ORG
RED
OFFOFF
T
GRN
WH
T
WH
BLU
AUTO
CLOSE
TIMETIMESTALL
FORCE
AUTO
CLOSE
STALL
FORCE
BLK
GRN
MASTER
CABLE
MASTER
CABLE
ALM
ALM
RED
PWR
BLK
RED
120
OFF
OFF
PULL
DLY.
OFF
OFF
S4 S4
GTO RCVR.
GTO RCVR.
RECEIVER
RECEIVER
GRN
BLK
LEARN
LEARN
LIMIT
SLV SLV
LIMIT
SHA
STATUS
STATUS
COM
COM
CONTROL INPUTS
CONTROL
INPUTS
COM
FORCE
AUTOAUTO
CLOSECLOSE
TIME TIME
STALLSTALL
FORCE
BLK
LE
CYCCOM
LE
ETY
CYC
SAF
TETY
EXI
SAF
T
DOW
EXI
SE
DOW
E
CLO
SHA
EDG
SE
EN
EE
CLO
OP
EDG
EDG
N
OPE E
GRN
EDG
LEARN
LEARN
RMT RMT
OFF OFF
120 120
MIN MIN
MAX MAX
S3 S3
SOFT SOFT
STARTSTART
OFF OFF
ON ON
WARNING
WARNING
OFF OFF
ON ON
LEARN
OPENOPEN PULLPULL
PUSHPUSH LEARN
MAST
LIMIT
MAST
LIMIT
SIMULT.
SLV SLV
OPENOPEN
DLY. DLY.
SIMULT.
MODE1 OFF OFF
MODE1
ON ON
S2 S2
MODE2 OFF OFF
MODE2
ON ON
MASTER CABLE
MASTER
CABLE
RED
BLK
LOCKLOCK
AUXAUX
PWR
7
BRN
BLU
G
ORBRN
RED
ORG
18 VAC
18 VAC or
or SOLAR
SOLAR
6
7
T
GTO
5
6
T
WH
GRN
BLU
WH
GTO TRANSF
TRANSF
4
5
BATT+
BATT+
3
4
BATTBATT-
2
3
BLK
GRN
POWER CONTROL
CONTROL
POWER
INPUTS
INPUTS
INPUTS
INPUTS
1
2
SECOND CABLE
SLAVE
CABLE
BLK
RED
AUTO CLOSE TIME
1
RED
ORG
SOFT START
WARNING
OPEN
SLV OPEN
MODE1
MODE2
FUSEFUSE
15 15
RLY
CHARGING
CHARGING
PWR INPWR IN
PWR
LOCK AUX
LOCK PWR
AUX RLY
18 VAC
GTO
AUX
18 VAC or
GTO
AUX
or SOLAR LOCK LOCK
SOLAR
GTO TRANSF
TRANSF
BRN
BLU
G
ORBRN
POWER
CONTROL
POWER
INPUTS CONTROL
INPUTS
INPUTS
INPUTS
GTO
GRN
T
WH
GRN
T
BLU
WH
Turn the “AUTO CLOSE TIME” arrow in the center of the potentiometer with small flat head screwdriver. Turning the pot all the way
counter-clockwise will turn the auto close feature off. The minimum
auto close time is 3 seconds.The maximum (turn the pot all the way
clockwise) auto close time is 120 seconds.
IMPORTANT: For safety reasons the obstructions setting or Stall Force on the GTO® gate
opener control board comes from the factory set at MIN (minimum). In many installations this
setting will need to be adjusted to overcome the weight and size of the gates.
ALWAYS KEEP SAFETY AT THE TOP OF YOUR LIST WHEN ADJUSTING OR SERVICING YOUR
AUTOMATIC GATE OPENER
Setting Personal Transmitter Code
All GTO transmitters are set to a standard code at the factory and are ready to operate your GTO® Gate Opener.
For your safety and security, however, we strongly recommend that you replace the factory setting with your own personal code.
Follow the directions below:
1
2
1
Remove back cover of the opener remote.
2
3
4
5
6
7
8
9
Flip transmitter over. Use small screwdriver to move switches to
random positions. If you have more than one transmitter, now is
a good time to set them all with the same code.
27
Control Box Settings
Setting Personal Transmitter Code
3
4
GTO
GTOTRANSF
TRANSF
POWER
CONTROL
POWER
INPUTS CONTROL
INPUTS
INPUTS
INPUTS
1515
FUSE
FUSE
RLY
GTO
AUX
GTO LOCKAUX
LOCK
CHARGING
CHARGING
PWR IN
PWR IN
PWR
LOCK AUX
LOCK PWRAUX RLY
18 VAC
18 VAC or
or SOLAR
SOLAR
1
3
4
4
6
5
5
G
ORBRN
G
OR
RED
BATT+
BATT+
3
BLU
BRN
BATTBATT-
2
SECOND CABLE
SLAVE CABLE
1
2
GRN
T
GRN
WH
T
WH
BLU
6
7
7
RED
BLK
MASTER CABLE
MASTER CABLE
AUTO
CLOSE
TIMESTALL
STALL
FORCE
AUTO
CLOSE
TIME
FORCE
BLK
GRN
T
GRN
WH
T
WH
BLU
BLU
BRN
G
BRN
OR
G
OR
RED
OFFOFF
120120MINMIN
SOFT
START
SOFT
START
OFFOFF
WARNINGOFFOFF
WARNING
OPEN
PULL
OPEN
PULL
OPENDLY.DLY.
SLV SLV
OPEN
MODE1
MODE1
OFFOFF
MODE2
MODE2
OFFOFF
AUTO CLOSE TIME
ON 4
3
2
4
1
3
2
1
RED
BLK
BLK
STATUS
ON
S4
S4
LEARN RMT
ALM
ALM
GRN
BLK
BLK
RED
RED
LEARN
LEARN
LIMIT
SLVSLVLIMIT
RECEIVER
RECEIVER
GTO RCVR.
GTO RCVR.
EDG SE
E
CLO
EN
E
OPEDG
N
EDG
OPE E
EDG
GRN
STALL FORCE
STATUS
STATUS
DOW
SHA DOW
SE
SHA E
CLO
LEARN
RMT
LEARN
RMT
MAX
MAX
S3 S3
ON ON
ON ON
LEARN
PUSH
LEARN
PUSH
MAST
LIMIT
SIMULT.MAST
LIMIT
SIMULT.
ONON
S2 S2
ONON
CONTROL INPUTS
CONTROL INPUTS
COM
COM
COM
COM
LE
CYC LE
CYC
ETY
SAF ETY
SAFT
EXI
T
EXI
120
MODE1
MODE2
MAX
ON
OFF
OFF
PULL
DLY.
1 2 3 4
SOFT START
WARNING
OPEN
SLV OPEN
MIN
OFF
OFF
ON
ON
PUSH
SIMULT.
ON
ON
S3
LEARN
MAST LIMIT
S2
Go to control box. Press and hold the remote and “LEARN RMT”
buttons simultaneously for 5 seconds or until the alarm sounds.
Replace and secure back cover of the transmitter.
5
6
GTO
TRANSF
15
FUSE
PWR IN
GTO
LOCK
AUX
RLY
CHARGING
PWR
AUX
1
4
67
5
65
BATT+
3
BATT-
2
T
WH
SLAVE CABLE
N
GR
BLU
BRN
6
7
G
OR
7
4
4
5
6
3
1
1
2
ON
2
3
3
4
4
ON
3
2
S2
Replace control box cover.
FCC Regulation
7
8
9
This device complies with FCC rules Part 15.
Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that
may cause undesired operation.
Fill In Code For Your Records
2
ON
ON
ON
6
1
5
S4
LEARN
MAST LIMIT
Example
4
S2
2
Release the remote button, then release the “LEARN RMT”
button. The new code is now programmed. Fill in boxes below
with your transmiter code for your records.
3
LEARN
SLV LIMIT
S3
S3
OFF
OFF
ON
ON
PUSH
SIMULT.
BLK
RED
ALM
GTO RCVR.
MAX
ON
1 2 3 4
MODE1
MODE2
OFF
OFF
PULL
DLY.
MIN
RECEIVER
ALM
ALM
120
SOFT START
WARNING
OPEN
SLV OPEN
2
DOW
GRN
LEARN RMT
OFF
1
T
EXI
SE
CLO E
EDG
EN
OP E
EDG
LEARN
MAST LIMIT
LE
CYC
ETY
SAF
SHA
STATUS
LEARN RMT
STALL FORCE
STATUS
AUTO CLOSE TIME
M
MAX
M
ON
ON
PUSH
SIMULT.
ON
ON
BLK
CO
BLK
RED
STALL FORCE
RED
120 MIN
BRN
G
OR
AUTO CLOSE TIME
T
WH
BLU
CO
CONTROL INPUTS
GRN
BLK
S4 S4
GTO
RCVR.
GTO
RCVR.
OPE E
GRN
EDG
LEARN
LEARN
SLV SLV
LIMIT
LIMIT
SE
E
EN
CLO
E
OP
EDG
EDG
N
RECEIVER
RECEIVER
SE
DOW
CLO E
SHA
EDG
GR
STATUS
STATUS
CONTROL
INPUTS
CONTROL
INPUTS
SHA
N
SOFT START OFF
WARNING OFF
OPEN
PULL
SLV OPEN DLY.
MODE1
OFF
MODE2
OFF
BLK
COM
COM
BLK
OFF
RED
BLK
COM
LE
COM
CYC
LE
CYCETY
SAF
ETY
T
EXI
SAF
T
EXI
DOW
RED
MASTER CABLE
BLU
BRN
G
BRN
OR
G
OR
RED
LEARN RMT
LEARN RMT
OFF OFF
120 120
MIN MIN
MAXMAX
S3 S3
SOFTSOFT
START
OFF OFF
ON ON
START
WARNING
OFF OFF
ON ON
WARNING
LEARN
OPENOPEN PULLPULL
PUSHPUSH
MASTLEARN
LIMIT
SLV SLV
OPENOPEN
DLY. DLY.
SIMULT.
SIMULT. MAST LIMIT
MODE1
ON ON
S2 S2
MODE1 OFF OFF
MODE2
ON ON
MODE2 OFF OFF
MASTER
CABLE
MASTER
CABLE
T
GRN
WH
T
WH
BLU
AUTOAUTO
CLOSE
TIME STALL FORCE
CLOSE TIME STALL FORCE
BLK
GRN
1
LOCK
45
BATT+
BATT+
43
BATTBATT-
23
G
OR
RED
BLK
RED
1
CONTROL
INPUTS
18 VAC
or
SOLAR
21
G
OR
BRN
SLAVE
CABLE
SECOND
CABLE
BRN
BLU
RED
POWER
INPUTS
15 15
FUSEFUSE
CHARGING
CHARGING
PWR IN
PWR IN
1
GTO GTO AUX AUX
LOCK LOCK
PWR PWRRLY RLY
LOCKLOCK
AUXAUX
18 VAC18 VAC
or or
SOLARSOLAR
GTO GTO
TRANSF
TRANSF
POWER
POWER CONTROL
CONTROL
INPUTS
INPUTS INPUTS
INPUTS
GRN
T
WH
GRN
T
BLU
WH
7
8
Transmitter distance may vary due to circumstances
beyond our control. NOTE: The manufacturer is
not responsible for any radio or TV interference
caused by unauthorized modifications to
this equipment. Such modifications could
void the user’s authority to operate
the equipment.
9
28
Connecting Additional Devices
Before You Begin
Although GTO strongly recommends the use of additional safety devices, we do not
endorse any specific brand names. Only use products that are certified and listed to
be in compliance with any applicable UL safety standards
(Underwriters Laboratories) and national and regional safety codes.
Call GTO Sales at 1-800-543-4283 for information on compatible products for your
specific application
PLEASE NOTE: Contact Sensors, Non-Contact Sensors, and Shadow Loops are not included with the GTO gate
opener. NOTE: Refer to the sensor manufacturer’s instructions for information about installing these devices on a
vehicular gate.
GTO gate openers will ONLY accept accessory devices with normally open dry contact output.
29
6
ABLE
5
ORG
RED
7
Connecting Additional Devices
BLK
Input Connections
BRN
ORG
1COM: Circuit common (reference for all logic input)
• Two (2) terminals to provide extra common connection point.
2CYCLE: (Typically for use with doorbell button or hardwired keypad)
• Each activation at this input will cycle the operation as follows:
….→ OPEN → STOP → CLOSE → STOP → OPEN → …
RED
BLK
1
COM
5
6
7
CLOSE
EDGE
OPEN
EDGE
7 OPEN EDGE: (Typically for use with safety edge device)
• Activation of this input while the gate is opening will cause the gate to stop and reverse direction for approximately 2 seconds.
• Activation of this input while the gate is closing has no effect (gate will continue to close).
• Activation of this input while gate is idle will prevent gate from opening.
30
BLK
RED
ALM
6 CLOSE EDGE: (Typically for use with safety edge device)
• Activation of this input while the gate is closing will cause the gate to stop and reverse direction for approximately 2 seconds.
• Activation of this input while the gate is opening has no effect (gate will continue to open).
• Activation of this input while gate is idle will prevent gate from closing.
GRN
RECEIVER
GTO RCVR.
5SHADOW: (Typically for use with loop detector device)
• This input is only monitored when the gate is at the fully open
position. At any other position, activation of this input has no effect on gate operation.
• Activation of this input while gate at the fully open position will
prevent gate from closing.
CONTROL INPUTS
COM
3SAFETY: (Typically for use with photo beam device, loop detector
2
CYCLE
or other non-contact sensors)
• Activation of this input while the gate is closing will cause the gate to SAFETY
3
stop and return to the opened position.
• Activation of this input while the gate is opening has no effect (gate EXIT
4
will continue to open).
• Activation of this input while gate is idle will prevent gate from closing.
SHADOW
4EXIT: (Typically for use with exit loop or wand)
• Activation of this input will open the gate if it’s not already at the
open position.
• Activation of this input while at open limit will restart the auto close time
(if enabled).
MASTER CABLE
GRN
NOTE:
• All control inputs are dry-contact, normally open, inputs. DO NOT apply external voltage sources to these inputs.
WHT
• All inputs are connected with respect to COMMON terminal.
• The status light will blink once when its corresponding input is activated.
BLU
Connecting Additional Devices
Connecting Accessories
CONTROL INPUTS
6
7
RED
BLK
ALM
CLOSE
EDGE
OPEN
EDGE
SHADOW
5
RECEIVER
GRN
4
3
SAFETY
CYCLE
2
COM
COM
BLK
RED
ORG
BRN
BLU
WHT
GRN
1
EXIT
MASTER OPERATOR
GTO RCVR.
6
7
According to
Application
1
Edge Sensor
3
1
GTO Photo Beams
1
2
Push Button Control
1
4
Vehicle Sensor
Refer to Vehicle Sensor
manual for additional
connections.
1
4
2
ABC
5
GHI
JKL
7
PRS
8
TUV
3
DEF
6
MNO
9
WXY
0
1
2
Keypad
NOTE: Connections are for typical
applications. There may be additional
connection options for applications that
are not illustrated here.
31
Connecting Additional Devices
Connecting GTO Automatic Lock
CONTROL OUTPUTS
G TO
LO C
POWER
INPUT
K
LOCK
PWR
AUX
RLY
GTO 18VOLT
TRANSF. OR
SOLAR PANEL
Wire from
Automatic
GTO Lock
GTO Lock:
For use exclusively with GTO Lock (FM142 or FM144).
Connecting other devices to these terminals may cause incorrect
operation and void your warranty. You do not use the lock board
with this control board.
GTO Lock Connection:
Connect the red and black leads from the lock to the GTO LOCK
terminal on the gate operator control board.
Connecting Other Auxiliary Devices (Mag Locks, Sirens, Lights. . .}
• These 2 terminals are normally open, dry-contact (no voltage) relay ouput.
• These 2 terminals are ON (shorted) whenever the gate is moving and OFF (opened) otherwise.
• These 2 terminals maximum rating is 24Vdc, 1 Amp.
Maintenance & Troubleshooting
Maintenance Tips
•C
lean the push-pull tube with a soft, dry cloth and
apply silicone spray to it at least once per month.
• On all gates weighing 250 lb. or more, routinely
grease the ball bearing hinges at least 4 times a year;
more frequently if the gates are near a coastal area.
• Keeping a few mothballs in the control box will
discourage insects from entering it and damaging the
control board.
32
Troubleshooting Guide
If your gate opener does not function properly after it is installed, use this guide before calling the GTO Service Department.
VOLTAGE READINGS
18 Vac Transformer.............................................................................................18.0 to 22.0 Vac, 2200 mA
5 W Solar panel (single).....................................................................................18.0 to 22.0 Vdc, 300 mA
* measure voltage at panel and control box.
Two 12 V, 7 amp hour Batteries......................................................................12.5 to 13.5 Vdc 7.0 Ah
*measure voltage at battery terminals with battery disconnected from circuit board
Charging circuit ..................................................................................................13.3 to 14.8 Vdc
*measure voltage at battery terminals with battery connected to circuit board and GREEN "POWER IN"
LED is ON.
Audible Feedback
Symptom
Diagnosis
Check:
1 short beep upon
activation
Blown Fuse
Low or Bad Battery
Loose Battery Connection
• Fuse
• Battery Under Load
• Battery Harness Connections
1 short beep upon
power up
Circuit Board Powered
Up & Ready
•
Normal Operation
Continuous
Uninterrupted Alarm
Circuit Board Senses an
Obstruction
•
•
•
•
•
Path of Gate
Gate for Level and Plumb
Stall Force Adjustment
Disconnect Safety Devices
Rev Counter
1 beep with 10 seconds
off
Low Battery Condition
•
•
•
Fuses
Battery Harness Connections
Battery Under Load
1 beep then 2 beeps
Master Motor Terminals
Shorted
•
•
•
•
Connections to Master Inputs
Master Arm Power Cable
Motor
Circuit Board
1 beep with 2 seconds
off
Master Arm Limit Switch
Error
• Connections to Master Inputs
• Master Arm Power Cable
3 beeps with 2 seconds
off
Master Arm Rev Counter
Error
• Connections to Master Inputs
• Master Arm Power Cable
• Rev Counter
33
Visual Feedback
Symptom
Diagnosis
Check:
Status (clear)
1 blink
Cycle Terminal
Shorted
Disconnect the push button, keypad, intercom keypad, or any other
accessory wired to this terminal. Try the remote. If the remote works, then
the problem is the accessory.
Status (clear)
2 blinks
Safety Terminal
Shorted
Disconnect the loop detector, photo beam, or any other accessory wired
to this terminal. Try the remote. If the remote works, the problem is the
accessory.
Status (clear)
3 blinks
Exit Terminal
Shorted
Disconnect exit wand, loop detector, photo beam, Knox box, or any other
accessory wired to this terminal. Try remote. If the remote works, the
problem is the accessory.
Status (clear)
4 blinks
Shadow Terminal
Shorted
Disconnect the loop detector, photo beam, or any other accessory wired to
this terminal. Try remote. If the remote works, the problem is the accessory.
Status (clear)
5 blinks
Close Edge Terminal
Shorted
Disconnect the edge sensor, photo beam, or any other accessory wired to this
terminal. Try the remote. If the remote works, the problem is the accessory.
Status (clear)
6 blinks
Open Edge Terminal
Shorted
Disconnect edge sensor, photo beam, or any other accessory wired to this
terminal. Try the remote. If the remote works, the problem is the accessory.
RF (yellow) Flickers
Receiving 318 MHz
RF
Normal operation when remote or wireless keypad is used.
RF (yellow) OFF
No 318 MHz RF
Received
•
•
•
•
Power (green) ON
AC or Solar Power
Present
Normal Operation
Power (green) OFF
No AC or Solar
Power
Transformer:
• Breaker or GFI
• Power at AC outlet.
• Output of Transformer.
• Voltage on wire at 18 VAC Input
Battery in Remote
Program Remote
Antenna Receiver Connections
Antenna Receiver
Solar:
• Weather
• Solar Panel Placement
• Output of Solar Panel
• Voltage on wire at Solar Input
Charge (red) ON
Fast Charging Mode
Battery Voltage should be ~14.8 VDC slowly increasing
Charge (red) Fast
Blinking 2/second
Soak Charging Mode
Battery Voltage should be ~14.1 VDC
Charge (red) Slow
Blinking 1/second
Float Charge
Battery Voltage should be ~13.8 VDC
Charge (red) OFF
Battery Not Being
Charged
•
•
•
•
AC power
Transformer
Solar Panel
Charging Circuit
34
Battery/Power Troubleshooting
RED LED
AUTO CLOSE TIME
FUSE
15
STALL FORCE
STATUS
BATT+
CHARGING
LEARN RMT
BATT-
OFF
120
MODE1
MODE2
MAX
ON
POWER IN
1 2 3 4
SOFT START OFF
WARNING
OFF
OPEN
PULL
2ND OPEN DLY.
MIN
OFF
OFF
ON
ON
PUSH
SIMULT.
S3
LEARN
MAST LIMIT
ON
ON
S2
CHARGING
LEARN
2ND LIMIT
POWER IN
S4
DIAG
PORT
GREEN LED
CONTROL OUTPUTS
RECEIVER
2ND OPERATOR
POWER IN LED
ON
ON
ON
OFF
OFF
OFF
CHARGING LED
Steady ON
Blinking
OFF
OFF
Blinking
Steady ON
BLK
RED
GRN
EXIT
ALM
CLOSE
EDGE
OPEN
EDGE
SHADOW
CYCLE
SAFETY
BLK
COM
COM
RED
ORG
BRN
7
BLU
6
GRN
5
BLK
4
RED
3
ORG
2
GRN
1
GTO 18 VOLT
TRANSF. OR
SOLAR PANEL
CONTROL INPUTS
MASTER OPERATOR
WHT
AUX
RLY
BRN
PWR
BLU
LOCK
WHT
POWER
INPUT
GTO RCVR.
Battery Charging
Battery Fully Charged
Bad Charger
No AC/Solar Power
Low Battery
Bad Charger
Repair Service
If your Gate Operator is not operating properly, please follow the steps below:
1. First use the procedures found in the Troubleshooting Guide (see page 25).
2. Use the 24/7 Troubleshooting Wizard at http://support.gtoinc.com.
3. If you are unable to solve the problem, call the GTO Service Department at (800) 543-1236, or (850) 5754144. Refer to the serial number (located on the right side of the control box) and date of purchase when
calling for assistance.
4. If repair or replacement of your gate operator is necessary, the Service Department will assign a Return
Goods Authorization (RGA) number to you.
5. Securely pack the component(s) authorized for return to the factory. Include a copy of your sales reciept
for the purchase of the product(s). Write the RGA number issued to you on the outside of the package in
LARGE BOLD PRINT.
Ship the package(s) freight prepaid to: GTO, 3121 Hartsfield Road, Tallahassee, Florida, USA 32303.
NOTE: Products returned to GTO without a Return Goods Authorization (RGA) number in LARGE
BOLD PRINT on the outside of the package WILL NOT be accepted. Also, items returned to GTO
freight collect WILL NOT be accepted.
GTO Technical Service and Installation Assistance
8:00am–7:00pm • Monday–Friday (EST)
Toll Free Support: 800-543-1236 • Local Support: 850-575-4144 • Fax: 850-575-8950
24/7 Troubleshooting Wizard: http://support.gtoinc.com
35
Accessories
Please visit www.gtoaccess.com for photos and detailed descriptions of GTO
Accessories. Or call 1-800-543-GATE (4283).
POWERING ACCESSORIES
Low Voltage Wire [RB509]
The 16 gauge, stranded, dual conductor low voltage Wire is for connecting the AC powered
transformer, solar panel or wired accessories to the system’s control board. This specially
designed wire is UV treated, PVC coated, and ready for direct burial.
Solar Panel Kits [FM122/FM123]
If your gate operator is more than 1000 ft. away from an AC power outlet, you can choose to
maintain the battery charge with the GTO Solar Panel Kit.
• 10 Watt Solar Panel Charging Kit [FM123]
• 5 Watt Solar Panel Charging Kit [FM122]
Additional/Replacement Battery [RB500]
For additional battery power or replacement.
“FROM VEHICLE” ENTRY AND EXIT ACCESSORIES
Transmitters [RB741/RB742/RB743]
Purchase an additional transmitter for each vehicle in your family. The Two-Button
Transmitter can be programmed to operate both your gate operator and a garage door
opener using the Universal Receiver. Or it can be programmed to open two gate operator
systems.
• Single Button Transmitter [RB741]
• Dual Button Transmitter [RB742]
• Three Button Transmitter [RB743]
Universal Receiver [RB709U-NB]
The Universal Antenna Receiver gives you the ability to use one remote to activate your
gate operator and your garage door opener. Connects to any brand garage door opener. Up
to 100 ft. range.
1
4
GHI
7
PRS
2
ABC
5
JKL
8
TUV
0
3
DEF
6
MNO
9
WXY
Digital Keypad [F310]
Allow friends access to your property using an identification code that you provide.
Program up to 25 entry codes for added security. Powered by three “AA” batteries (not
included).
36
Ans
wer
Per Grant
mis
sio
n
Ke
Ba ypa
tt d
Low
POW
ER
Residential Wireless Entry Intercom [F3100MBC]
Designed for added security to your automated gate with the ability to “speak to” and
“screen” visitors safely from inside your home. Ideal for securing gate entrances while
providing controlled access.
DV
9V
Gooseneck Pedestal [F100/F110]
Designed to mount digital keypads, wireless intercom systems, and other access control
devices for your gate automation system.
“HANDS FREE” Entry & Exit Accessories
Driveway Vehicle Sensor [FM139]
Automatically activates gate operator “Hands-Free” when a vehicle exits the property.
Electromagnetic sensor detects vehicles in motion.
• 50 ft. [FM139]
• 100 ft. [FM140]
• 150 ft. [FM141]
Wireless Vehicle Sensor [R4500]
Automatically activates gate operator “Hands-Free” when a vehicle exits the property.
100 ft. range between transmitter and receiver. Easy installation.
LOCKING & SECURITY Accessories
ATIC
OM CK ®
AUTE LOLO
CK
GASETCURITY
IC
TRON
ELEC
1
4
GHI
7
PRS
2
ABC
5
JKL
8
TUV
0
3
DEF
6
MNO
®
9
WXY
SEC
URITY
, Inc.
GATE
LOC
K
Automatic Gate Lock [FM144/FM142]
The #1 Accessory For Swing Gate Operators! Designed for added security in conjunction
with GTO Automatic Gate Operators. The gate lock unlocks and locks automatically
when the gate opens and closes. The perfect solution for high wind conditions.
Bulldog Pedestrian Gate Lock [FM145]
Designed to mount on horizontal swing “walk through” wood, chain link, and metal
pedestrian gates opening in or out. Ideal for securing pools, condominiums, schools
and any pedestrian gate.
Wireless Driveway Alarm [R4450].
This device alerts you of vehicles entering your driveway (with or without an automated
gate). The indoor base station signals you with a door chime when a vehicle passes the
driveway sensor.
37
ADDITIONAL Accessories
Photo Beams [R4222]
Primary “through beam” photo beam device. Provides “non-contact” entrapment
protection.
Pin Lock [FM345]
Use as a substitute for the clevis pin at the front mount of the gate opeator to prevent
theft of the operator.
• Pin Lock 10-pack: ten Pin Locks keyed alike [FM345KA].
Push Button Control [RB101]
Wire this unlit push button directly to your gate operator for simple open/close/stop
operation from up to 1000 ft. away. Use 16 gauge low-voltage wire.
Replacement Transformer [RB570]
Standard 18 volt, 2200 mA AC transformer included with the gate operator to maintain
battery charge.
HARDWARE Accessories
Push To Open Brackets [347IH]
Required when the gate operator must push a gate open (arm extends to open), such
as away from a sloping driveway or where space prevents gate from opening into the
property (pull to open). Order two brackets for a dual swing gate installation.
Column Mount Lock Receiver [433IH]
For use with the Automatic Gate Lock or Bulldog Pedestrian Gate Lock when mounting
on brick columns or applications with limited space.
If you have a question about any special order item,
just call 1-800-543-GATE!
The contents of all material available on this installation manual are copyrighted by Gates That Open, LLC (“GTO”), unless otherwise indicated. All rights are reserved by GTO, and content may not be reproduced, downloaded, disseminated, published, or transferred in any form or by any means, except with the prior, written permission of GTO. Any reprinting of GTO publications is by permission only. Copyright
infringement is a violation of federal law.
Mighty Mule¨, E-Z Gate¨, GTO¨, are registered trademarks of Gates That Open, LLC America’s DIY Automatic Gate Openers is a trademark of GTO and are the exclusive property of Gates That Open, LLC.
All rights are reserved by GTO, and these marks may not be used, in any for without the prior, written permission of GTO.
38
3121 Hartsfield Road • Tallahassee, Florida, USA 32303
Telephone GTO Sales: 1-800-543-GATE (4283) or (850) 575-0176 • Fax (850) 575-8912
or GTO Technical Service: 1-800-543-1236 or (850) 575-4144 • Fax (850)575-8950
www.gtoaccess.com­
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement