MODEL: M2XRP2 [1] INPUT ENCODER SPEED TRANSMITTER Super-mini Signal Conditioners Mini-M Series

MODEL: M2XRP2 [1] INPUT ENCODER SPEED TRANSMITTER Super-mini Signal Conditioners Mini-M Series
MODEL: M2XRP2
Super-mini Signal Conditioners Mini-M Series
[1] INPUT
0: User-calibrated (Factory default: open collector, 0 – 100 kHz)
ENCODER SPEED TRANSMITTER
(PC programmable; built-in excitation)
Functions & Features
• Converts a two-phase forward and reverse rotation
pulse signal with 90 degree phase difference into a forward
and reverse speed signal
• Built-in excitation
• PC programmable input and output ranges
• Input pulse monitoring LED
• Direct RS-422 input
• CE marking
• UL approval
Typical Applications
• Measuring moving speed of a machine with a rotary
encoder
[2] EXCITATION
0: User-calibrated (Factory default: 12 V DC / 5 mA)
If the unit is to be factory-calibrated to a specific
voltage value, please select from the following:
1: 5 V DC / 5 mA
4: 12 V DC / 5 mA
[3] OUTPUT
0: User-calibrated (Factory default: 4 – 20 mA)
29.5 (1.16)
Model
If the unit is to be factory-calibrated to a specific
input type, please select from the following:
A: Open collector
B: Voltage pulse
J: RS-422 line driver pulse
If the unit is to be factory-calibrated to a specific
output type, please select from the following:
Current
Z1: Range 0 – 20 mA DC
Voltage
V1: Range -2.5 – +2.5 V DC
V2: Range -10 – +10 V DC
(Configurator software is used to change output over the
described range of the selected suffix code. For changing
out of this range, set the Output Range Selectors inside the
unit before software adjustment.)
76
(2.99)
124
(4.88)
mm (inch)
MODEL: M2XRP2-[1][2][3]-[4][5]
ORDERING INFORMATION
• Code number: M2XRP2-[1][2][3]-[4][5]
Specify a code from below for each [1] through [5].
(e.g. M2XRP2-000-M2/CE/Q)
• Specify the specification for option code /Q
(e.g. /C01/S01)
• Non-specified orders will be shipped at default factory
settings (M2XRP2-000: Open collector input/12 V
excitation/4 – 20 mA output). However, a power suffix code
must be specified.
If you specify a full code number without specific calibration
ranges, the input frequency is factory set to the maximum
range available for the selected input code and the output is
set to the default range. Use Ordering Information Sheet
(No. ESU-5059).
Note: Must be used with its socket. NOT installable to a
multi-unit installation base. (e.g. model: M2BS-16)
http://www.m-system.co.jp/
[4] POWER INPUT
AC Power
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
(90 – 264 V for UL)
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
P: 110 V DC
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)
(110 V ±10 % for UL)
[5] OPTIONS (multiple selections)
Standards & Approvlas (must be specified)
/N: Without CE or UL
/CE: CE marking
/UL: UL approval, CE marking
Other Options
M2XRP2 SPECIFICATIONS
ES-5059 Rev.7 Page 1/5
MODEL: M2XRP2
blank: none
/Q: Option other than the above (specify the specification)
(UL not available)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
TERMINAL SCREW MATERIAL
/S01: Stainless steel
RELATED PRODUCTS
• JX configurator connection kit (model: JXCON)
GENERAL SPECIFICATIONS
Construction: Plug-in
Connection: M3 screw terminals (torque 0.8 N·m)
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Overrange output: Approx. -15 to +115 % at 1 – 5 V
Zero adjustment: -5 to +5 % (front)
Span adjustment: 95 to 105 % (front)
Configuration: Via PC Configurator Software (model:JXCON)
on the Windows PC connected to
the front jack.
Programmable features include:
· I/O type and range
· Zero and span adjustments
· Low-end cutout
· Linearization
Status indicator LED: Red LED; Flashing patterns indicate
different operating status of the transmitter.
Input monitor (PL1): Green LED blinks according to the input
phase A.
Input monitor (PL2): Green LED blinks according to the input
phase B.
Excitation adjustment: 5V or 12V DC
Configurator connection: 2.5 dia. miniature jack;
RS-232-C level
Pulse sensing: DC coupled or capacitor coupled selectable
with DIP SW
Low-end cutout: 100 msec. – 100 sec. or no cutout
programmable
INPUT SPECIFICATIONS
Excitation: Shortcircuit protection; 20 mA max. at
shortcircuit
Maximum frequency: 200 kHz
Frequency ranges:
http://www.m-system.co.jp/
0 – 10 mHz, 0 – 100 mHz, 0 – 1 Hz, 0 – 10 Hz, 0 – 100 Hz,
0 – 1 kHz, 0 – 10 kHz, 0 – 100 kHz
(Choose 100 kHz range to set the zero/span frequencies
lower than -100 kHz (higher than 100 kHz in the reverse
direction) or higher than 100 kHz (higher than 100 kHz in
the forward direction.))
Minimum pulse width time requirement: 2.5 μsec.
Minimum span: 10 % of the selected frequency range
Noise filter: See table 2
■ Open Collector
Input requirements
EXCITATION
SENSING
OFF
ON
5V
Approx. 5 V
≥200 kΩ
≤200 Ω
12 V
Approx. 10 V
≥200 kΩ
≤200 Ω
Amplitude: 5 - 12 V
Detecting level:
5 V excitation: 1 V
12 V excitation: 2 V
(Detecting voltage in the internal circuit.
For open collector input, be sure to re-adjust the voltage
back to 1 V (5 V excitation) or 2 V (12 V excitation) if it has
been changed for other input types.)
Detecting pulse edge: OFF to ON
If not specified, the input range is 0 Hz – 1 kHz.
■ Voltage Pulse
Waveform: Square or sine
Input impedance: 10 kΩ min.
Pulse amplitude: 0.1 – 30 Vp-p
Pulse amplitude Range: See table 1.
Max. voltage between input terminals: See table 1.
Sensitivity Scale: See table 1.
Detecting level: -2 – +4 V
Detecting pulse state: A pulse rise detected when the input
voltage goes above the detecting level;
a pulse sink detected when it goes below the level.
If not specified, the input range is 0 Hz – 1 kHz.
■ RS-422 Line Driver Pulse
Receiver: Conforms to RS-422
If not specified, the input range is 0 Hz – 1 kHz.
[Table 1]
SENSITIVITY
MAX.INPUT
PULSE AMPLITUDE
SCALE
VOLTAGE
RANGE
10 – 30 Vp-p
30 V
1/6
5 – 10 Vp-p
10 V
1/2
1 – 5 Vp-p
5V
1
0.1 – 1 Vp-p*
1V
5
*Input frequency within ±50 kHz
When the parameters have been set with DIP switches and the
PC Configurator Software (model: JXCON), a specific sensitivity
scale is applied according to the pulse amplitude setting. The
scaled input voltage is then compared to the preset detecting
level (-2.00 to +4.00 V).
With DC coupling, the scaled maximum voltage must be higher
than the detecting level and the minimum voltage must be lower
than that so that the pulse state is accurately detected. (Refer to
the instruction manual for detailed information about adjusting the
detecting level.)
M2XRP2 SPECIFICATIONS
ES-5059 Rev.7 Page 2/5
MODEL: M2XRP2
[Table 2]
Weight: 150 g (0.33 lbs)
FREQUENCY RANGE
NOISE FILTER TYPE
0 – 10 mHz
With
0 – 100 mHz
With
0 – 1 Hz
With
0 – 10 Hz
W/O
0 – 100 Hz
W/O
0 – 1 kHz
W/O
0 – 10 kHz
W/O
0 – 100 kHz
W/O
Be sure to apply the noise filter appropriate for the selected
frequency range as shown in the table above. The accuracy
may not be assured if no filter is applied.
OUTPUT SPECIFICATIONS
■ DC Current
Output range: 0 – 20 mA DC
Conformance range: 0 – 23mA DC
Minimum span: 1 mA
Offset: Lower range can be any specific value within the
output range provided that the minimum span is
maintained.
Load resistance: Output drive 12 V max.
(e.g. 4 – 20 mA: 600 Ω [12 V / 20 mA])
If not specified, the output range is 4 – 20 mA DC.
■ DC Voltage
Code V1 (narrow spans)
Conformance range: -3 – +3 V DC
Output range: -2.5 – +2.5 V DC
Minimum span: 250 mV
Code V2 (wide spans)
Conformance range: -11.5 – +11.5 V DC
Output range: -10 – +10 V DC
Minimum span: 1 V
Offset: Lower range can be any specific value within the
output range provided that the minimum span is
maintained.
Load resistance: Output drive 1 mA max.
(e.g. 1 – 5 V: 5000 Ω [5 V / 1 mA])
If not specified, the output range is shown below.
V1: 0 – 1 V DC
V2: 1 – 5 V DC
INSTALLATION
Power Consumption
•AC Power input:
Approx. 4 VA at 100 V
Approx. 5 VA at 200 V
Approx. 6 VA at 264 V
•DC power input: Approx. 3 W
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
http://www.m-system.co.jp/
PERFORMANCE
Accuracy: Input accuracy + output accuracy
Input accuracy: ≤ ±0.03% of the selected freq. range
Output accuracy: ≤ ±0.03% of the selected output range
The input accuracy is inversely proportional to the input
span; while the output accuracy is likewise inversely
proportional to the output span. With [Input Range / Input
Span] ≤ 1, the input accuracy is fixed at ±0.03%.
See CALCULATION EXAMPLES OF OVERALL ACCURACY.
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) of I/O range
at -5 to +55°C [23 to 131°F]
Response time: 0.5 sec. + 1 pulse cycle (0 – 90 %)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
CALCULATION EXAMPLES OF OVERALL ACCURACY
[Example] Open collector input, 0 – 50 kHz; 1 – 5 V output.
Selected freq. range (100 kHz) ÷ Input span (50 kHz)×
Accuracy (0.03 %)= 0.06 % (Input accuracy)
Selected output range (20 V) ÷ Output span (4 V) ×
Accuracy (0.03 %)= 0.15 % (Output accuracy)
Overall accuracy = 0.06 + 0.15 = ±0.21 %
STANDARDS & APPROVALS
CE conformity:
EMC Directive (2004/108/EC)
EMI EN 61000-6-4: 2007
EMS EN 61000-6-2: 2005
Low Voltage Directive (2006/95/EC)
EN 61010-1: 2001
Installation Category II
Pollution Degree 2
Input or output to power: Reinforced insulation (300 V)
Input to output: Basic insulation (300 V)
Approval:
UL/C-UL nonincendive Class I, Division 2,
Groups A, B, C, and D hazardous locations
(ANSI/ISA-12.12.01:2007, CAN/CSA-C22.2 No.213:1987)
UL/C-UL general safety requirements
(UL 61010B-1:2003, CAN/CSA-C22.2 No.61010-1:1992)
M2XRP2 SPECIFICATIONS
ES-5059 Rev.7 Page 3/5
MODEL: M2XRP2
EXTERNAL VIEW
■ FRONT VIEW (with cover open)
Input Selector SW
■ LEFT SIDE VIEW (with cover removed)
Configurator Jack
ON OFF ON OFF
1
2
Input Monitor LED, PL1
OFF
1
2
SW1
Input Monitor LED, PL2
4 3 2 1
SW2
ON
SW3
Status Indicator LED
Zero/Span Selector
Top: SPAN
Middle: OFF
Bottom: ZERO
Output Selector SW
ON OFF
UP/DOWN Switches
4
3
2
1
The front cover cannot be opened to 180 deg.
when flush with neighboring units.
SW4
Refer to the instruction manual for detailed procedures.
OPERATION
OUTPUT
+10V
OUTPUT
20mA
4mA
rev. 30 Hz
–10V
rev. 100 Hz
fwd. 100 Hz
CUTOUT
fwd. 100 Hz
STOP
FORWARD
REVERSE
φ A INPUT
φ B INPUT
+
ACCEL.
DECEL.
0 Hz
–
ACCEL.
CUTOUT
Forward Rotation: Phase A leads the Phase B by 90 degrees.
Reverse Rotation: Phase A lags behind Phase B by 90 degrees.
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
6 (.23)
DIN RAIL
35mm wide
11–M3
SCREW
21.5 (.85) 7.3 (.29)
86.7 (3.41)
116.7 (4.59)
9
8 7
11 10
22 (.87)
[4 (.16)]
72 (2.83)
59 (2.32)
5 4
29.5 (1.16)
4 (.16)
70.5 (2.78)
2–4.2x5
(.17x.20)
MTG HOLE
6 (.24) deep
3 2 1
6
• When mounting, no extra space is needed between units.
http://www.m-system.co.jp/
M2XRP2 SPECIFICATIONS
ES-5059 Rev.7 Page 4/5
MODEL: M2XRP2
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
■OPEN COLLECTOR, VOLTAGE INPUT
INPUT
MON. PL1
φA
+ 1
COM
– 2
φB
+ 5
+ 4
CONFIGURATOR
JACK
3
ZERO/SPAN
SELECTOR
INPUT TYPE
SELECTOR
ROTARY
ENCODER
PWR
STATUS
MON.
6
Isolation
Waveform
Shaper
Digital
Computation
Output
Driver
7 +
OUTPUT
8 –
UP/DOWN
SWITCHES
Waveform
Shaper
10 U(+)
POWER
Exc.
Supply
INPUT
MON. PL2
11 V(–)
9
Base Socket
Remark: The sensor excitation voltage is supplied also across the terminals 3 – 6.
■RS-422 LINE DRIVER INPUT
STATUS MON.
ROTARY
ENCODER
ZERO/SPAN
SELECTOR
COM
– 6
φA
+ 1
φA
– 2
φB
+ 4
φB
– 5
PWR
+ 3
CONFIGURATOR
INPUT
MON. PL1
RS-422
Receiver
INPUT
MON. PL2
9
Isolation
Digital
Computation
Output
Driver
7 +
OUTPUT
8 –
RS-422
Receiver
UP/DOWN
SWITCHES
10 U(+)
POWER
Excitation
Supply
11 V(–)
JACK
Base Socket
Specifications are subject to change without notice.
http://www.m-system.co.jp/
M2XRP2 SPECIFICATIONS
ES-5059 Rev.7 Page 5/5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement