General Manual 05/2007
SUGGESTED SPECIFICATIONS FOR CONVEYOR
MODEL TM-SP
Tray Make-up Conveyor to be SOUTHERN ENGINEERING SYSTEMS by Duke Mfg Co.,
model TMSP, UL and ETL Listed, and NSF approved commercial kitchen conveyor.
Conveyor Belt to be low friction, acetal slats, 10” wide. Slats joined with stainless steel removable pin
connectors.
Conveyor Bed to be constructed on #14-gauge, 300 series stainless steel with 1-1/2” high x 2” wide
channel edge on both sides and ends turned down square. Sides formed integral to top. Polish stainless
steel to a #3 finish.
Drive Housing to be a welded stainless steel frame with removable 16-gauge stainless steel access
door. Stainless steel scrap pan located beneath drive housing for easy removal. Drive housing to be
supported by four 1-5/8" O.D., 16-gauge stainless steel legs and stainless steel adjustable bullet feet.
Drive Type to be variable speed, DC motor, 120 volts, 60-cycle, 1-phase, ½ H.P. controlled by on/off
switch and variable speed controller.
Drive end of conveyor furnished with one bed mounted Limit Switch to control the flow of trays.
Anti-jam silver saver plate provided to prevent foreign material form jamming drive system.
Conveyor supported by 1-5/8” 16-gauge stainless steel tubing Legs with welded stainless steel cross
rails. Leg frames fitted into enclosed, round stainless steel gussets welded to stainless steel channel
braces and fitted with stainless steel adjustable bullet feet.
Optional UL Listed Electrical Raceway constructed of 16-gauge, 300 series stainless steel with #3
finish. Raceway furnished with removable top cover and fitted with properly sized receptacles and
stainless steel face plates, pre-wired to a panel box at the end of the conveyor. Panel box to be housed
in stainless steel enclosure fitted with hinged, locking, 18-gauge stainless steel door.
Conveyor to be pre-wired and factory tested.
Conveyor to carry UL and ETL listing and shall be NSF approved. Equipment built in an ISO
9001:2000 approved manufacturing facility.
BY
"Your Solutions Partner"
2305 N. Broadway
St. Louis, MO 63012
Ph 314-231-1130
Fax 314-231-5074
www.dukemfg.com
5/07
Optional Accessories
12” Wide Slat-Pin Belt
Stainless Raceway & Panel Box
Mobile Package (Note: Max 100Amp Main
Cord & Plug with Optional Raceway)
Flanged Feet
Additional Start-Stop Station
Foot Switch (Momentary Stop)
Cord & Plug (Without Raceway)
Auto-wash System
Flush-Wash (Drip pan and Drains only.)
Prison Security Package
S/S Belt Cover W/Hanger Brackets
Movable Over Shelf _____Dbl.
Stationary Over Shelf _____Dbl
Stationary Under Shelf
Removable Under Shelf
3” High x 1-1/4” Rolled Rim Sides
7/8” High x 1-1/4” Marine Edge Sides
Other _____________________________
_____________________________
COMMENTS/NOTES ____________________________________________________________
SHOWN WITH OPTIONAL S.S. RACEWAY & S.S.
PANELBOX. RACEWAY FITTED WITH OPTIONAL
RECEPTACLES
22 1/2"
2"
2"
10"
BELT
2"
8"
10"
BELT
START STOP STATION
RECESSED INTO END
PANEL.
1 5/8" O.D. 16 GA. S.S. TUBING LEGS
WITH 1 1/4" O.D. 16 GA. S.S. TUBING
CROSSRAILS.
3'-0"
1 1/2"
2"
22 1/2"
18 GA. S.S. ACCESS DOOR TO ENCLOSE
ELECTRIC PANEL BOX. DOOR MOUNTED
ON FULL HEIGHT PIANO HINGE AND
FITTED WITH RECESSED HANDLE,
KEY LOCK
8 3/8"
ACCESS COVER TO
ELECTRIC WIRING
SECTION VIEW
END ELEVATION
NOTE: CASTERS NOT AVAILABLE WHEN PANEL BOX INCOMING
SERVICE EXCEEDS 100AMPS.
MODEL #TM-SP10-NW-VS
'- "
120/60/1 ELECTRIC SUPPLY FOR DRIVE MOTOR
1'-4"
2'-2"
DRIVE HOUSING
1'-10 1/2"
START-STOP STATION
END LIMIT SWITCH
0-40 F.P.M
SILVER SAVER SWITCH
14 GA. S.S. SLIDER PAN OF UNI-BODY CONST.
W/2" WIDE CHANNEL EDGE FULL LENGTH
OF CONVEYOR. ENDS TURN DOWN STRAIGHT.
PLAN VIEW
END LIMIT SWITCH
SLIDE OUT CRUMB
DRAWER
8"
MASTER DISCONNECT
W/ VARIABLE SPEED
CONTROL KNOB
3'-0"
START-STOP STATION
DRIVE HOUSING 26" WIDE, REMOVABLE
16GA. TYPE 304 S.S. ACCESS PANELS,
18GA. S.S. CRUMB PAN MOTOR,
1/2HP 120V/60HZ/1PH 5AMPS
We reserve the right to change specifications and product design without notice. Such revisions do
not entitle buyers to corresponding changes, improvements, additions or replacements for
previously purchased equipment.
Model TM-SP
Item Number: ____________
SLAT-PIN BELT
TRAY MAKE-UP CONVEYOR
SOUTHERN ENGINEERING SYSTEMS
SOUTHERN ENGINEERING SYSTEMS Model TM-SP, UL and ETL Listed and NSF
approved tray make-up conveyors are engineered to meet the unique design criteria required to
satisfy client needs.
These Tray Make-up conveyor systems meet the performance needs for tray feeding and
banquet plating operations. Our extended life slat-pin belting provide years of economical
service. Combined with energy efficient DC drive systems, maintenance free sealed for life
bearings and adjustable torque limits for safety; SOUTHERN ENGINEERING SYSTEMS
Tray Make-up Conveyors lead the way.
SOUTHERN ENGINEERING SYSTEMS conveyors have been built to last by
craftsman for over 52 year, carry an 18 month parts and labor warranty, plus an additional 4
year motor warranty, and conform to or exceed all known federal regulatory requirements.
PROJECT NAME: _________________________________
PROJECT LOCATION: _______________________________
SE-TMSP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement