FOSROC Renderoc BB SDS (AUS)

FOSROC Renderoc BB SDS (AUS)
Safety Data Sheet
Hazardous Substance, NON-Dangerous Goods
1. MATERIAL AND SUPPLY COMPANY IDENTIFICATION
Product name:
FOSROC RENDEROC BB
Recommended use: Cementitious mortar for use with elastomeric bridge bearings. Applied by hand
trowelling or flowed.
Supplier:
ABN:
Street Address:
Telephone:
Parchem Construction Suppliers Pty Ltd
80 069 961 968
7 Lucca Road
Wyong NSW 2259
Australia
(02) 4350 5000
Emergency telephone number:
Australia – 1800 033 111
New Zealand – 0800 734 607
2. HAZARDS IDENTIFICATION
AUSTRALIA CLASSIFICATION
This material is hazardous according to health criteria of Safe Work Australia.
Signal Word
Danger
Hazard Classification
Skin Corrosion/Irritation – Category 2
Serious Eye Damage/Irritation – Category 1
Sensitisation – Skin – Category 1A
Carcinogenicity – Category 1A
Specific Target Organ Toxicity (Single Exposure) – Category 3
Specific Target Organ Toxicity (Repeated Exposure) – Category 2
Hazard Statement(s)
H315
Causes skin irritation
H317
May cause an allergic skin reaction
H318
Causes serious eye damage
H335
May cause respiratory irritation
H350
May cause cancer by inhalation
H373
May cause damage to organs through prolonged or repeated exposure
Prevention Precautionary Statement(s)
P102
Keep out of reach of children
P103
Read label before use
P201
Obtain special instructions before use
P202
Do not handle until all safety precautions have been read and understood
P261
Avoid breathing dust
P264
Wash hands, face and all exposed skin thoroughly after handling
Product name: FOSROC RENDEROC BB
Issued: 31 March 2015
SDS No: PARGHSEN000039
Version: 1.0
Page: 1 of 7
Safety Data Sheet
P271
P272
P280
Use only outdoors or in a well-ventilated area
Contaminated work clothing should not be allowed out of the workplace
Wear protective clothing, gloves, eye/face protection and suitable dust mask as required
Response Precautionary Statement(s)
P101
If medical advice is needed, have product container or label at hand
P312
Call a POISON CENTRE or doctor/physician if you feel unwell
P302+352
IF ON SKIN: Wash with soap and water
P362
Take off contaminated clothing and wash before reuse
P363
Wash contaminated clothing before reuse
P333+313
If skin irritation or a rash occurs: Get medical advice/attention
P304+340
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for
breathing
P314
Get Medical advice/attention if you feel unwell
P305+351+338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if
present and easy to do – continue rinsing
P310
Immediately call a POISON CENTRE or doctor/physician
Storage Precautionary Statement(s)
P405
Store locked up
P403+233
Store in a well ventilated place. Keep container tightly closed
Disposal Precautionary Statement(s)
P501
Dispose of contents/container in accordance with local, regional, national and international
regulations
Poisons Schedule (Aust): Not applicable
DANGEROUS GOODS CLASSIFICATION
Not classified as Dangerous Goods by the criteria of the “Australian Code for the Transport of Dangerous
Goods by Road & Rail” and the “New Zealand NZS5433: Transport of Dangerous Goods on Land”.
3. COMPOSITION INFORMATION
CHEMICAL ENTITY
Portland cement
Sand, containing >0.1% crystalline silica
Other ingredients determined not to be hazardous
CAS NO.
PROPORTION
65997-15-1
14808-60-7
-
10 - 30%
>60%
Balance
________
100%
4. FIRST AID MEASURES
If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New Zealand
0800 764 766).
Inhalation: Remove victim from exposure - avoid becoming a casualty. Remove contaminated clothing
and loosen remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at
rest until fully recovered. Seek medical advice if effects persist.
Skin contact: If skin or hair contact occurs, immediately remove contaminated clothing and flush skin and
hair with running water. Continue flushing with water until advised to stop by the Poisons Information Centre
or a Doctor; or for 15 minutes and transport to Doctor or Hospital.
Product name: FOSROC RENDEROC BB
Issued: 31 March 2015
SDS No: PARGHSEN000039
Version: 1.0
Page: 2 of 7
Safety Data Sheet
Eye contact: Immediately irrigate with copious quantities of water for 15 minutes. Eyelids to be held open.
Remove clothing if contaminated and wash skin. Urgently seek medical assistance. Transport to hospital or
medical centre.
Ingestion: Rinse mouth with water. If swallowed, do NOT induce vomiting. Give a glass of water to drink.
Never give anything by the mouth to an unconscious patient. If vomiting occurs give further water. Seek
medical advice.
PPE for First Aiders: Wear overalls, chemical goggles and impervious gloves. Avoid generating and
inhaling dusts. If dust exists, wear dust mask/respirator meeting the requirements of AS/NZS 1715 and
AS/NZS 1716. Available information suggests that gloves made from nitrile rubber should be suitable for
intermittent contact. However, due to variations in glove construction and local conditions, the user should
make a final assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash
contaminated clothing and other protective equipment before storing or re-using.
Notes to physician: Treat symptomatically. Can cause corneal burns.
5. FIRE-FIGHTING MEASURES
Hazchem Code: Not applicable.
Suitable extinguishing media: Not combustible, however, if material is involved in a fire use water fog (or if
unavailable fine water spray), foam, dry agent (carbon dioxide, dry chemical powder).
Specific hazards: Non-combustible material.
Fire fighting further advice: On decomposing may emit toxic fumes. Fire fighters to wear self-contained
breathing apparatus and suitable protective clothing if risk of exposure to products of decomposition.
6. ACCIDENTAL RELEASE MEASURES
SMALL SPILLS
Wear protective equipment to prevent skin and eye contamination. Wipe up with absorbent (clean rag or
paper towels). Allow absorbent to dry before disposing with normal household garbage.
LARGE SPILLS
Wear protective equipment to prevent skin and eye contamination and the inhalation of dust. Work up wind
or increase ventilation. Cover with damp absorbent (inert material, sand or soil). Sweep or vacuum up, but
avoid generating dust. Collect and seal in properly labelled drums for disposal. If contamination of sewers
or waterways has occurred advise local emergency services.
Dangerous Goods – Initial Emergency Response Guide No: Not applicable.
7. HANDLING AND STORAGE
Handling: Avoid skin and eye contact and inhalation of dust.
Storage: Store in a cool, dry, well-ventilated place and out of direct sunlight. Store away from incompatible
materials described in Section 10. Keep containers closed when not in use - check regularly for spills.
8. EXPOSURE CONTROLS AND PERSONAL PROTECTION
Product name: FOSROC RENDEROC BB
Issued: 31 March 2015
SDS No: PARGHSEN000039
Version: 1.0
Page: 3 of 7
Safety Data Sheet
National occupational exposure limits: No value assigned for this specific material by Safe Work
Australia.
However for:
TWA
ppm
Inspirable dust
mg/m3
-
10
ppm
STEL
mg/m3
-
-
CARCINOGEN
CATEGORY
NOTICES
-
-
As published by the Safe Work Australia.
TWA - The time-weighted average airborne concentration over an eight-hour working day, for a five-day
working week over an entire working life.
These Exposure Standards are guides to be used in the control of occupational health hazards. All
atmospheric contamination should be kept too as low a level as is workable. These exposure standards
should not be used as fine dividing lines between safe and dangerous concentrations of chemicals. They
are not a measure of relative toxicity.
If the directions for use on the product label are followed, exposure of individuals using the product should
not exceed the above standard. The standard was created for workers who are routinely, potentially
exposed during product manufacture.
Biological Limit Values: As per the “National Model Regulations for the Control of Workplace Hazardous
Substances (Safe Work Australia)” the ingredients in this material do not have a Biological Limit Allocated.
Engineering measures: Use only in well ventilated areas. Avoid generating and inhaling dusts. Use with
local exhaust ventilation or while wearing dust mask. Keep containers closed when not in use.
Personal protection equipment: OVERALLS, SAFETY SHOES, CHEMICAL GOGGLES, GLOVES,
DUST MASK.
Wear overalls, chemical goggles and impervious gloves. Avoid generating and inhaling dusts. If dust exists,
wear dust mask/respirator meeting the requirements of AS/NZS 1715 and AS/NZS 1716. Available
information suggests that gloves made from nitrile rubber should be suitable for intermittent contact.
However, due to variations in glove construction and local conditions, the user should make a final
assessment. Always wash hands before smoking, eating, drinking or using the toilet. Wash contaminated
clothing and other protective equipment before storing or re-using.
Hygiene measures: Keep away from food, drink and animal feeding stuffs. When using do not eat, drink
or smoke. Avoid skin and eye contact and inhalation of dust. Ensure that eyewash stations and safety
showers are close to the workstation location.
9. PHYSICAL AND CHEMICAL PROPERTIES
Form / Colour / Odour: Grey powder containing cement and graded aggregates with a cementitious odour.
Solubility:
Specific Gravity (23°C):
Relative Vapour Density (air=1):
Vapour Pressure (20 °C):
Flash Point (°C):
Flammability Limits (%):
Autoignition Temperature (°C):
% Volatile by Volume:
Melting Point/Range (°C):
Insoluble in water
1.45
N App
N App
N App
N App
N App
N Av
N Av
Product name: FOSROC RENDEROC BB
Issued: 31 March 2015
SDS No: PARGHSEN000039
Version: 1.0
Page: 4 of 7
Safety Data Sheet
Boiling Point/Range (°C):
Decomposition Point (°C):
pH:
Viscosity:
N App
N Av
N Av
N Av
(Typical values only - consult specification sheet)
N Av = Not available
N App = Not applicable
10. STABILITY AND REACTIVITY
Reactivity: No reactivity hazards are known for the material.
Chemical stability: This material is thermally stable when stored and used as directed.
Hazardous reactions: No known hazardous reactions.
Conditions to avoid: Keep free of moisture.
Incompatible materials: Incompatible with acids and bases. Avoid contact with water. Wet portland
cement is highly alkaline.
Hazardous decomposition products: Oxides of calcium and silica.
11. TOXICOLOGICAL INFORMATION
No adverse health effects expected if the product is handled in accordance with this Safety Data Sheet and
the product label. Symptoms or effects that may arise if the product is mishandled and overexposure occurs
are:
Acute Effects
Inhalation: Material is an irritant to mucous membranes and respiratory tract.
Skin contact: Contact with skin will result in irritation. A skin sensitiser. Repeated or prolonged skin
contact may lead to allergic contact dermatitis.
Ingestion: Swallowing can result in nausea, vomiting and irritation of the gastrointestinal tract.
Eye contact: A severe eye irritant. Corrosive to eyes: contact can cause corneal burns. Contamination of
eyes can result in permanent injury.
Acute toxicity
Inhalation: This material has been classified as non-hazardous.
Skin contact: This material has been classified as non-hazardous.
Ingestion: This material has been classified as non-hazardous.
Corrosion/Irritancy: Eye: this material has been classified as a Category 1 Hazard (irreversible effects to
eyes). Skin: this material has been classified as a Category 2 Hazard (irritant to skin).
Sensitisation: Inhalation: this material has been classified as not a respiratory sensitiser.
Skin: this material has been classified as not a Category 1A Hazard (skin sensitiser).
Aspiration hazard: This material has been classified as non-hazardous.
Product name: FOSROC RENDEROC BB
Issued: 31 March 2015
SDS No: PARGHSEN000039
Version: 1.0
Page: 5 of 7
Safety Data Sheet
Specific target organ toxicity (single exposure): This material has been classified as a Category 3
Hazard. Exposure via inhalation may result in respiratory irritation.
Chronic Toxicity
Mutagenicity: This material has been classified as non-hazardous.
Carcinogenicity: This material has been classified as a Category 1A Hazard.
Reproductive toxicity (including via lactation): This material has been classified as non-hazardous.
Specific target organ toxicity (repeat exposure): This material has been classified a Category 2 Hazard.
Exposure via inhalation may result in effects on the lungs, ie silicosis.
12. ECOLOGICAL INFORMATION
Avoid contaminating waterways.
Acute aquatic hazard: No information is available to complete an assessment.
Long-term aquatic hazard: No information is available to complete an assessment.
Ecotoxicity: No information available.
Persistence and degradability: No information available.
Bioaccumulative potential: Risk of bioaccumulation in an aquatic species is low.
Mobility: Low mobility in soil.
13. DISPOSAL CONSIDERATIONS
Persons conducting disposal, recycling or reclamation activities should ensure that appropriate personal
protection equipment is used, see “Section 8. Exposure Controls and Personal Protection” of this SDS.
If possible material and its container should be recycled. If material or container cannot be recycled,
dispose in accordance with local, regional, national and international Regulations.
14. TRANSPORT INFORMATION
ROAD AND RAIL TRANSPORT
Not classified as Dangerous Goods by the criteria of the “Australian Code for the Transport of Dangerous
Goods by Road & Rail” and the “New Zealand NZS5433: Transport of Dangerous Goods on Land”.
MARINE TRANSPORT
Not classified as Dangerous Goods by the criteria of the International Maritime Dangerous Goods Code
(IMDG Code) for transport by sea.
AIR TRANSPORT
Not classified as Dangerous Goods by the criteria of the International Air Transport Association (IATA)
Dangerous Goods Regulations for transport by air.
Product name: FOSROC RENDEROC BB
Issued: 31 March 2015
SDS No: PARGHSEN000039
Version: 1.0
Page: 6 of 7
Safety Data Sheet
15. REGULATORY INFORMATION
This material is not subject to the following international agreements:
Montreal Protocol (Ozone depleting substances)
The Stockholm Convention (Persistent Organic Pollutants)
The Rotterdam Convention (Prior Informed Consent)
Basel Convention (Hazardous Waste)
International Convention for the Prevention of Pollution from Ships (MARPOL)
This material/constituent(s) is covered by the following requirements:

All the constituents of this material are listed on the Australian Inventory of Chemical Substances
(AICS).
16. OTHER INFORMATION
Literary reference
This Safety Data Sheet has been prepared by Chemical Data Services Pty Ltd (chemdata.com.au) on behalf
of its client.
Supersedes: 11 January 2013
Reason(s) For Issue: Revised. Format change. Change in Hazardous Substance Classification.
Technical Support: Australia - 1300 737 787, New Zealand – 0800 657 156
Safety Data Sheets are updated frequently. Please ensure that you have a current copy.
This SDS summarises at the date of issue our best knowledge of the health and safety hazard information of
the product, and in particular how to safely handle and use the product in the workplace. Since Parchem
Construction Supplies Pty Ltd and Concrete Plus cannot anticipate or control the conditions under which the
product may be used, each user must, prior to usage, review this SDS in the context of how the user intends
to handle and use the product in the workplace.
If clarification or further information is needed to ensure that an appropriate assessment can be made, the
user should contact this company.
Our responsibility for product as sold is subject to our standard terms and conditions, a copy of which is sent
to our customers and is also available upon request.
Product name: FOSROC RENDEROC BB
Issued: 31 March 2015
SDS No: PARGHSEN000039
Version: 1.0
Page: 7 of 7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement