EPVM operation manual (20151207)s
WARNING
Contents
Enhanced Public View Monitor
WARNING
1
Pacakge Contents
1. Package Contents
RISK OF ELECTRIC SHOCK
DO NOT OPEN
To reduce the risk of electric shock do not remove cover(or back).
No user serviceable parts inside. Refer servicing to qualified service personnel.
2. Features
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of "dangerous voltage"
within a product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
3. Specifications
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
4. Device Operation Manual
WARNING
To prevent fire of shock hazard, do not expose the set to rain or moisture.
Do not rub or strike the Active Matrix LCD with anything hard, as this may
scratch, mar, or damage the Active Matrix LCD permanently.
REGULATORY INFORMATION
One of WDL-EPVM5 / WDL-EPVM7 / WDL-EPVM8
/ WDL-EPVM10 with internal SD card
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
or correct the interference by one or more of the following measures.
Enhanced Public View Monitor
Quick Guide for
WDL-EPVM5
WDL-EPVM7
WDL-EPVM8
WDL-EPVM10
Installation CD & manual
Quick Guide for
WDL-EPVM5
WDL-EPVM7
WDL-EPVM8
WDL-EPVM10
This manual provides information on installation
and operation of the EPVM. EPVMs installed in
the store will be used for purposes of advertising
, such as video surveillance via the output and
built-in camera. EPVM is WELDEX’s DVR
solution that can be used as a video output, as
well as take images when motion is detected
with the built-in camera, which is stored in the
SD memory card. This system can be used as a
effective in-store security system.
12V DC power supply with powercode
2
Features
4
Device Operation Manual
1) Monitor
The display switches between camera display
and advertisement when motion is detected.
> Features
- High quality & cost-effective
- Low power consumption for cost saving
- Built-in WDR HD camera with motion sensor
- Built-in removable SD card for displaying advertising or corporate message
- On-board DVR including SD card slot
- Switch from advertisement display to camera video on motion activity
- User-definable text warning message
- Built-in alarm I/O
- VESA mounting pattern for ceiling or wall mount options
- Compatible S/W solution (verint nextiva 6.x, march video sphere R5)
2) Speaker
3) Camera
When motion is detected, the image
is stored in the SD memory card
while it is displayed on the monitor.
3
Specifications
Section
Display
Screen size
Resolution
Brightness
Contrast ratio
Response time
WDL-EVPM5
5"
800×480
600 cd/㎡
Camera
Storage
Interface
Alarm I/O
Speaker
User I/F
Power
Environmental
Dimensions
Mount
Power adapter
Power
consumption
Operating
temperature
Humidity
Outline
dimension (mm)
Weight
②
WDL-EVPM8 WDL-EVPM10
7"
800×480
400 cd/㎡
500 : 1
< 20ms
Viewing angle
Aspect ratio
Image sensor
Lens
Active pixel
Frame rate
Shutter
Wide dynamic
Range
Sensitivity
WDL-EVPM7
There is a output of Alarm sound. (Coming soon)
①
8"
800×480
450 cd/㎡
140(H) / 120(V)
4) IR Receiver
③
10.4"
800×600
450 cd/㎡
300 : 1
< 30ms
150(H) /
110(V)
16 : 9
1/2.7" omnivision 1.3M progressive C-MOS
Fixed 3.7㎜ F2.0
1280(H)×720(V)
30 fps
Rolling shutter
④
⑤
Can receive signals from the remote
controller that comes with it. (Coming soon)
5) Status Indicators
Operation Status
Red
Green
-
ON
Recording video
Flash, slow
ON
Back-up video
Flash, fast
ON
Upgrade S/W
ON
ON
Power ON
4:3
⑥
115 ㏈
⑦
3650 ㎷/Lux-sec
Internal Micro SD card slot for recording
External micro SD card slot for backup, media, upgrade
Terminal block 4P
1W mono speaker
Remote controller (coming soon)
Power, record LEDs
VESA™ 75×75㎜
12VDC 4A
⑧
6) External SD Card Slot
⑨
Back-up Operation
1. In external SD Card “backup_media” folder is created.
(Only lowercase recognized)
2. While the product is operating or booting, the memory is stored
in the external SD card.
3. If the Red LED is rapidly fleshing, files stored inside the created folder
is copied.
4. After the copying is finished, Red LED stops flashing.
< 0.5A
0℃ ~ 50℃
S/W Upgrade Operation
10 ~ 90% RH, non condensing
140(W)×121(H)×24(D)
184(W)×148(H)×27(D)
220(W)×172(H)×27(D)
254(W)×232(H)×27(D)
-
-
-
-
1. The upgrade file provided by the manufacturer should be copied
into the root of the external SD card.
2. External SD card is inserted when the product is operating or booting.
3. When the Red LED is ON, this means that upgrade has started.
Do not turn off power or remove the SD card during this time.
4. When the upgrade is complete, the Red LED will turn off
and reboot will start automatically.
Is used to store advertisement playback,
camera image back-up, and software update.
7) Alarm I/O Connector
When alarm is triggered, camera image
is stored and there will be output in the alarm.
8) Power connector
It is a connection for power.
(Use the adapter supplied)
9) VESA™ Mount
VESA™ Mount 75×75㎜
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement