Submittal 1449FA Comby
®
Penal-Ware 1449FA Series
ADA 2010 Compliant - Lav/Toilet Comby - Offset Toilet Bowl - Front Access
Federal
Public Law
111-380
(No Lead)
1449FA-LO-2-BPH-PBH-04-DMB-BPH
Fixture May Show Some Available Options
Please visit www.acorneng.com for most current specifications.
ADA 2010 Compliant - Lav/Toilet Comby - Offset Toilet Bowl
Fixture is arranged to be installed on finished wall and serviced through removable access panels. Panels are secured with
vandal resistant fasteners and are located on the face of the cabinet, on the open side of the cabinet and below the lavy section.
Fixture cabinet and toilet are fabricated from 14 gage, type 304 stainless steel and polished to a satin finish. The inside of the
toilet bowl also includes a satin finish. Cabinet interior is sound deadened with fire-resistant material. Optional Wall Sleeve or
Metal Template is recommended for all installations to provide required wall openings. Unit complies with the accessibility
requirements of ANSI, UFAS, ADA, and OBC regarding toilet and lavatory fixtures. Compliance is subject to the interpretation and
requirements of the local code authority.
Lavatory ‘D’ Bowl is 15-1/4” x 12-1/2” x 4" deep. Standard P-trap waste outlet is 1-1/2" O.D. plain end.
Spouts selections are located on the deck to the rear of the bowl with valve controls located to the right and/or left of the DMS
spout or DMB bubbler option.
Optional Valve may be an Air-Control pneumatically operated, pushbutton valve with 1.4 GPM flow control for the DMS spout
option and 0.70 GPM flow control for the DMB bubbler options. Pushbutton requires less than 5 lbs. to activate valve. Valve is
metering, non-hold open type. Timing is from 5 to 60 seconds. Valve can be remotely located up to 10 feet from the operating
pushbutton. Valve and bubbler conform to the requirements of for NSF61, section 9 and is IAPMO R&T certified to meet the lead
free requirements of Section 1417 of the Federal Safe Drinking Water Act and Section 116875 of the California Health & Safety
Code.
Toilet is blowout jet type with elongated bowl manufactured to ASME A112.19.3 and CSA B45.4 requirements and will flush with
a minimum of 25 PSI flow pressure when used in conjunction with a minimum of 1.6 GPF. Trap has a minimum 3-1/2" seal and
will pass a 2-1/8" ball. Toilet waste is gasket waste. Unit is provided with Suicide Resistant Skirt (SPS, optional on other fixtures).
Grab Bar is heavy gage type 304 stainless steel construction, 1-1/2” diameter, extends the width of the fixture and measures
47-3/8” long from center to center. Grab bar is positioned behind toilet and is integral to the cabinet.
GUIDE SPECIFICATION
Provide and install Acorn Penal-Ware ADA 2010 Lav/Toilet-Comby-Offset Toilet Bowl (specify model number and options). Fixture
shall be fabricated from type 304 stainless steel. Construction shall be seamless welded and exposed surfaces shall have a satin
finish. Provide 36" minimum long stainless steel grab bar to be located behind toilet. Fixture shall have an Air-Control
pneumatically operated, metering, non-hold open pushbutton valve. Valve shall require less than 5 lbs. to activate. Valve and
bubbler conform to the requirements of NSF61, section 9 and is IAPMO R&T certified to meet the lead free requirements of
Section 1417 of the Federal Safe Drinking Water Act and Section 116875 of the California Health and Safety Code. Toilet shall be
concealed blowout jet type with an elongated bowl, a self-draining flushing rim, and an integral contoured seat. Fixture shall be
cUPC certified and toilet shall meet ASME A112.19.3 and CSA B45.4 requirements and will flush with a minimum of 25 PSI flow
pressure when used in conjunction with a minimum of 1.6 GPF. Toilet trap shall have a minimum 3-1/2" seal that shall pass a 21/8" diameter ball and be fully enclosed. Cabinet interior is to be sound deadened with fire-resistant material. Fixture shall
withstand loadings of 5,000 pounds without permanent damage. Fixture shall be furnished with necessary fasteners for proper
installation.
Page 1
P.1449FA
Revised: 11/23/15
Acorn Engineering Company • 15125 Proctor Avenue • P.O. Box 3527 • City of Industry, CA 91744-0527 U.S.A.
Tel: (800) 488-8999 • (626) 336-4561 • Fax: (626) 961-2200 • www.acorneng.com • E-mail: [email protected]
Penal-Ware® 1449FA: ADA 2010 - Lav/Toilet Comby - Offset Toilet Bowl - Front Access
7
2
1. DECK MOUNTED SPOUT &
PUSHBUTTONS FOR -04-M
VALVE OPTION
1
2 HYDRAULIC FLUSH
PUSHBUTTON
19"
(483)
3. OPTIONAL DMB-BPH DRINKING
BUBBLER & PUSHBUTTON
4. GRAB BAR
5. 42" LONG GRAB BAR BY
OTHERS
4
5
21"
(533)
6. ACCESS PANELS
7. WALL ANCHORS BY
OTHERS
8. SPS STYLE SKIRT FEATURE
STANDARD
1" (794)
314
18" (457)
1" (1251)
494
TOILET CABINET
HEIGHT
LAVY DECK
HEIGHT
5" (16)
8
6
2
1
3
421" (114)
3
6
33"
(838) 29"
(737)
6
18"
(457)
8
8
Page 2
P.1449FA
Revised: 11/23/15
Acorn Engineering Company • 15125 Proctor Avenue • P.O. Box 3527 • City of Industry, CA 91744-0527 U.S.A.
Tel: (800) 488-8999 • (626) 336-4561 • Fax: (626) 961-2200 • www.acorneng.com • E-mail: [email protected]
Penal-Ware® 1449FA: ADA 2010 - Lav/Toilet Comby - Offset Toilet Bowl - Front Access
WALL THICKNESS AND TYPE (Must Specify)
Thickness: ________ Type: o Concrete o Block o Steel
MODEL AND OPTIONS SELECTION:
BASE MODEL NUMBER
3 1449FA
o
49" Lav-Toilet Comby
TOILET ORIENTATION (Must Specify)
o -LO
Left Offset
o -RO
Right Offset
FIXTURE MOUNTING AND WASTE (Must Specify)
o -2
On-Floor, Wall Outlet
o -3
On-Floor, Floor Outlet
CABINET OPTIONS
o -FMT
Fixture Mounted Trim
o -GBC
Grab Bar Closure Plate
o -LGB
Less Grab Bar
o -PH
Paper Holder, not ADA Compliant
(Opposite Toilet/Offset Orientation)
o -TB
Toothbrush Holder Single Hole
(Installed on lavy side of unit)
o -TG
12 Gage Cabinet
o -TH
Towel Hook, o Single o Double
(Installed on lavy side of unit)
o -VG5
Vent Grille 7-1/2" x 10-1/2”
LAVATORY WASTE OPTIONS
o -CW
Combined Waste
o -OF
Lavatory Overflow
SPOUT SELECTION (Must Specify)
o -DMS
Deck Mounted Spout
o -DMB
Deck Mounted Bubbler (In Lieu of Spout)
o -BC Bubbler, Code
o -BP Bubbler, Penal
o -BPH Bubbler, Penal Hemispherical
VALVE SELECTION (Must Specify)
o -03-M
Air-Control, Single Temp, Metering
o -04-M
Air-Control, H & C, Metering
o -9
Punching for Valve by Others
(Specify Punching)
o -EVS1
Electronic Valve System - Single Temp
o -EVSP1
Electronic Valve System - Single Temp
w/ Piezo Pushbutton
o -EVS2
Electronic Valve System - Hot & Cold
o -EVSP2
Electronic Valve System - Hot & Cold
w/ Piezo Pushbuttons
o -MVC1
Time-Trol - Single Temp
o -MVC1-BAT Time-Trol - Single Temp, Battery Operated
(Battery Not Included)
o -MVC2
Time-Trol - Hot & Cold
o -MVC2-BAT Time-Trol - Hot & Cold, Battery Operated
(Batteries Not Included)
o -PPZ1
Programmable Piezo Button, Single Temp
w/ 9VDC Transformer
o -PPZ2
Programmable Piezo Buttons, Hot & Cold
w/ 9VDC Transformer
FLUSH VALVE GPF (Must Specify)
o -1.28 GPF (HET)
o -1.6 GPF
o -3.5 GPF
FLUSH VALVE OPTIONS (Must Specify)
o -EVSFV
Electronic Flush Valve
o -EVSPFV
Electronic Flush Valve
w/ Piezo Pushbutton
o -FVBO
Flush Valve By Others
o -FVH
Flush Valve, Hydraulic
o -MVCFV
Time-Trol Electronic Flush Valve
TOILET OPTIONS
o -FT
Flood-Trol (Manual Reset)
o -FTA
Flood-Trol Auto-reset
o -FTE
Flood-Trol Electronic
o -HET
High Efficiency Toilet Design
o -HPS
High Polished Seat
o -PE
Plain End Waste Outlet, Extended 3”
Beyond Back of Fixture
o -TSC
Toilet Shipping Cover
o -TWE
Toilet Waste Extension, (3” Standard w/ PE)
Specify Length Beyond
Fixture: __________
o -WO3B
2-3/8” OD P-Trap w/ 3" OD
Plain End Waste Outlet Connection,
Extended 3” Beyond Back of Fixture
VALVE OPTIONS
o -BRS
Brass Body Valve
o -CI
Cycle Interrupt for Time-Trol Valves
o -MA2
2 Station Valve Manifold
o -PBH
Hemispherical Pushbutton
o -TF
Transformer, 120VAC to 24VAC for
MVC Time-Trol Options
PRODUCT OPTIONS
o -EG
Enviro-Glaze, Specify Color: __________
Toilet Exterior & Interior
o -EGE
Enviro-Glaze, Specify Color: __________
Toilet Exterior Only
o -DMB
Deck Mounted Drinking Bubbler
(Cold water only) Not applicable with
-03-M tempered supply
o -BP Penal Style
o -BC Code Style
o -BPH Penal Hemispherical Style
o -LPFV
Less Punching for Flush Valve
o -MT
Metal Template
(Only 1 required per project)
o -SW
Wall Sleeve
o -VAC
AcornVac Systems
Please visit www.acorneng.com
for most current specifications.
Important: Installation instructions and current rough-in are furnished with each fixture. Do not rough in without certified dimensions.
Dimensions are subject to manufacturer's tolerance of plus or minus 1/4" and change without notice. Acorn assumes no responsibility for use of void or superseded data. © Copyright Acorn Engineering Company
Selection Summary
Approved for Manufacturing
Model No. & Options___________________________
Company__________________Title______________
Quantity____________________________________
Signature_________________ Date______________
Page 3
P.1449FA
Revised: 11/23/15
Acorn Engineering Company • 15125 Proctor Avenue • P.O. Box 3527 • City of Industry, CA 91744-0527 U.S.A.
Tel: (800) 488-8999 • (626) 336-4561 • Fax: (626) 961-2200 • www.acorneng.com • E-mail: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement