datasheet for TEN 3-0523N by Traco Electronic AG

datasheet for TEN 3-0523N by Traco Electronic AG
DC/DC Converters
TEN 3N Series, 3 Watt
CB
Features
◆ Wide 2 : 1 input range
◆ Input filter to meet EN 55022, Class A
Scheme
UL 60950-1
and FCC, level A without external
components
◆ Extended operating temperature
range –40°C to 85°C
◆
◆
◆
◆
I/O isolation 1’500 VDC
DIP-24 package
High reliability, MTBF >1.0 Mio. h
3-year product warranty
The TEN 3N Series is a drop in replacement of the prevalent TEN 3 Series. The upto date design enables a cost reduction without any compromise to reliability and
function. They come with an internal filter to meet EN55022 class A without external
components. Increased EMC immunity and extended operating temperature range
of -40°C to 85°C make these converters an ideal solution for cost critical but demanding applications. With the standard pinning it is a drop in replacement for common
3 Watt converters in DIP24 package.
Models
Ordercode
TEN 3-0510N
TEN 3-0511N
TEN 3-0512N
TEN 3-0513N
TEN 3-0515N
TEN 3-0521N
TEN 3-0522N
TEN 3-0523N
TEN 3-1210N
TEN 3-1211N
TEN 3-1212N
TEN 3-1213N
TEN 3-1215N
TEN 3-1221N
TEN 3-1222N
TEN 3-1223N
TEN 3-2410N
TEN 3-2411N
TEN 3-2412N
TEN 3-2413N
TEN 3-2415N
TEN 3-2421N
TEN 3-2422N
TEN 3-2423N
TEN 3-4810N
TEN 3-4811N
TEN 3-4812N
TEN 3-4813N
TEN 3-4815N
TEN 3-4821N
TEN 3-4822N
TEN 3-4823N
http://www.tracopower.com
Input voltage range
4.5 – 9.0 VDC
(nominal 5 VDC)
9 – 18 VDC
(nominal 12 VDC)
18 – 36 VDC
(nominal 24 VDC)
36 – 72 VDC
(nominal 48 VDC)
Output voltage
3.3 VDC
5.0 VDC
12 VDC
15 VDC
24 VDC
±5.0 VDC
±12 VDC
±15 VDC
3.3 VDC
5.0 VDC
12 VDC
15 VDC
24 VDC
±5.0 VDC
±12 VDC
±15 VDC
3.3 VDC
5.0 VDC
12 VDC
15 VDC
24 VDC
±5.0 VDC
±12 VDC
±15 VDC
3.3 VDC
5.0 VDC
12 VDC
15 VDC
24 VDC
±5.0 VDC
±12 VDC
±15 VDC
Output current max.
600 mA
500 mA
250 mA
200 mA
125 mA
±250 mA
±125 mA
±100 mA
600 mA
500 mA
250 mA
200 mA
125 mA
±250 mA
±125 mA
±100 mA
600 mA
500 mA
250 mA
200 mA
125 mA
±250 mA
±125 mA
±100 mA
600 mA
500 mA
250 mA
200 mA
125 mA
±250 mA
±125 mA
±100 mA
Efficiency typ.
77 %
78 %
82 %
82 %
81 %
77 %
81 %
81 %
79 %
81 %
85 %
85 %
84 %
80 %
84 %
84 %
79 %
81 %
85 %
85 %
84 %
80 %
84 %
84 %
79 %
81 %
85 %
85 %
84 %
80 %
84 %
84 %
Page 1 of 4
DC/DC Converters
TEN 3N Series
3 Watt
Input Specifications
Input current no load
5
12
24
48
Vin
Vin
Vin
Vin
models
models
models
models
65 mA typ.
35 mA typ.
20 mA typ.
15 mA typ.
Start-up voltage
5
12
24
48
Vin
Vin
Vin
Vin
models:
models:
models:
models:
4.5 VDC (or lower)
9 VDC (or lower)
18 VDC (or lower)
36 VDC (or lower)
Under voltage shut down (lock-out circuit)
5
12
24
48
Vin
Vin
Vin
Vin
models:
models:
models:
models:
4.0 VDC max.
8.5 VDC max.
17.5 VDC max.
35.5 VDC max.
Surge voltage (1 sec. max.)
5
12
24
48
Vin
Vin
Vin
Vin
models
models
models
models
11 V max.
25 V max.
50 V max.
100 V max.
Reflected ripple current
5
12
24
48
Vin
Vin
Vin
Vin
models
models
models
models
100 mA typ
30 mA typ.
15 mA typ.
10 mA typ.
Conducted noise
EN 55022 class A without external components
ESD (electrostatic discharge)
EN 61000-4-2, air ±8 kV, contact ±6 kV,
perf. criteria A
Radiated immunity
EN 61000-4-3, 10 V/m, perf. criteria A
Fast transient / surge (with external input capacitor)
EN 61000-4-4, ±2 kV, perf. criteria A
EN 61000-4-5, ±1 kV perf. criteria A
Nippon chemi-con KY 220 µF, 100 V, ESR 48 mOhm
– external input capacitor
Conducted immunity
EN 61000-4-6, 10 Vrms, perf. criteria A
Short circuit input power
2000 mW max.
Internal power dissipation
1200 mW max.
Output Specifications
Voltage set accuracy
Regulation
±2 % max.
– Input variation Vin min. to Vin max.
1.0 % max.
– Load variation 0 – 100 %
single output models 1.0 % max.
dual output models balanced load 2.0 % max.
Minimum load
not required
Ripple and noise (20 MHz bandwidth)
70 mVpk-pk max
Transient response time (25% load step change)
500 µs max.
Transient response deviation (25% load step change)
±5 % max.
Temperature coefficient
±0.02 %/K
Current limitation
>120 % of Iout max., constant current
Short circuit protection
continuous
http://www.tracopower.com
Page 2 of 4
DC/DC Converters
TEN 3N Series
3 Watt
Output Specifications (continued)
Capacitive load
3.3
5.0
12
15
24
±5.0
±12
±15
VDC
VDC
VDC
VDC
VDC
VDC
VDC
VDC
models:
models:
models:
models:
models:
models:
models:
models:
680 µF max.
470 µF max.
330 µF max.
220 µF max.
100 µF max.
220 µF max (each output)
150 µF max. (each output)
100 µF max. (each output)
General Specifications
Temperature ranges
– Operating (natural convection cooling 20 LFM)
– Case temperature
– Storage
–40°C to +85°C
+100°C max.
–55°C to +125°C
Derating
3.3 %/K above 70°C
Humidity (non condensing)
95 % rel H max.
Reliability, calculated MTTF (MIL-HDBK-217 F, @ +25°C, ground benign)
>1 Mio. h
Isolation voltage (60 sec.)
– Input/Output
1’500 VDC
Isolation capacitance
– Input/Output
300 pF max.
Isolation resistance
– Input/Output (500 VDC)
>1‘000 M Ohm
Switching frequency
90 kHz min. (pulse frequency modulation PFM)
Safety standards
cUL/UL 60950-1, IEC/EN 60950-1
Safety approval
CSA file no. 226037
http://directories.csa-international.org
Environmental compliance
www.tracopower.com/products/reach-declaration.pdf
RoHS directive 2011/65/EU
– Reach
– RoHS
ng
Application note: www.tracopower.com/products/ten3n-application.pdf
ndi
Pe
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
http://www.tracopower.com
Page 3 of 4
DC/DC Converters
TEN 3N Series
3 Watt
Physical Specifications
Casing material
non conductive FR4
Potting material
epoxy (UL 94V-0 rated)
Pin material
copper alloy with gold plated subplate
Weight
12.8 g (0.45 oz)
Soldering temperature
max. 260°C / 10 sec.
Outline Dimensions
Pin-Out
11
2.54
15.24
(0.6)
(0.1)
4.5
20.3
14
10.2
(0.4)
4.5
(0.18)
(0.1)
16
2.54
23 22
15.24
Bottom view
(0.8)
9
(0.6)
2 3
Pin
Single
Dual
2
–Vin (GND)
–Vin (GND)
3
–Vin (GND)
–Vin (GND)
9
No pin
Common
11
ntc
–Vout
14
+Vout
+Vout
16
–Vout
Common
22
+Vin (Vcc)
+Vin (Vcc)
23
+Vin (Vcc)
+Vin (Vcc)
ntc = not to connect
5.08
(0.2)
22.86
(0.9)
(0.18)
31.8
(1.25)
Dimensions in [mm], () = Inch
Pin diameter ø 0.5 ±0.05 (0.02 ±0.002)
Tolerances ±0.5 (±0.02)
Pin pich tolerances ±0.25 (±0.01)
Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
Rev. February 24. 2013
www.tracopower.com
Page 4 of 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement