Sharp | FO-885 | Specifications | Sharp FO-885 Specifications

Sharp FO-885 Specifications
MODEL
FO-885
FACSIMILE
OPERATION MANUAL
1. Installation
2. Using the Answering Machine
3. Sending Documents
4. Receiving Documents
5. Making Copies
6. Making Telephone Calls
7. Special Functions
8. Option Settings
9. Printing Reports and Lists
10. Maintenance
11. Troubleshooting
WARRANTY
Facsimile Products
Congratulations on Your Purchase!
This Sharp product is warranted against manufacturing defects for a period of twelve (12) months from
the date of original purchase.
In the event of any defect arising in the equipment during the warranty period, such repairs should only
be carried out by the Dealer from which the unit was originally purchased or a Service Centre approved
by Sharp to service this type of equipment. These repairs would be carried out at no charge to the
owner, subject to the conditions specified herein.
The owner is responsible for any transportation and insurance costs if the product has to be returned
for repair.
This warranty does not extend to accessories or defects or injuries caused by or resulting from causes
not attributable to faulty parts or the manufacture of the product, including but not limited to, defect or
injury caused by or resulting from misuse, abuse, neglect, accidental damage, improper voltage, liquid
spillage, vermin infestation, software, use of consumables other than those approved by Sharp, or any
alterations made to the product which are not authorised by Sharp.
Please retain your sales documentation, as this should be produced to validate a warranty claim.
This warranty is in addition to and in no way limits, varies or excludes any express and implied rights
and remedies under any relevant legislation in the country of sale. However, to the extent permitted by
such legislation, Sharp excludes any liability for any indirect or consequential damages arising from the
purchase or use of the product.
To the extent permitted by law, Sharp excludes all implied warranties and conditions and where the
product is one that is not normally required for personal, domestic or household use, Sharp limits its
liability to the repair or replacement (at Sharp's option) of materials or workmanship which are found by
Sharp to be defective.
For your reference, please enter the particulars of your purchase below and retain, with your purchase
documentation.
Model No.
Serial No.
Date of Purchase
Place of Purchase
SPform046 (2Sept97)
FOR LOCATION ENQUIRIES WITHIN
FOR THE SERVICING OF PRODUCTS
AUSTRALIA
PURCHASED IN
REGARDING YOUR LOCAL
SHARP APPROVED SERVICE CENTRE
NEW ZEALAND
CALL THE
SHARP SERVICE REFERRAL CENTRE
FREECALL: 1 300 15 50 22
FACSIMILE: (02) 9672 1210
DURING NORMAL BUSINESS HOURS
SHARP CORPORATION OF AUSTRALIA PTY. LIMITED
A.C.N. 003 039 405
1 Huntingwood Drive, Huntingwood NSW 2148
CONTACT YOUR SELLING DEALER/RETAILER
OR FOR REFERRAL TO A
SERVICE CENTRE,
CALL SHARP CUSTOMER SERVICES
TELEPHONE: 09 634 7699
FACSIMILE: 09 636 6972
SHARP CORPORATION OF NEW ZEALAND LIMITED
Cnr Mahunga Drive & Hastie Avenue,
Mangere, AUCKLAND
Important Notice: This warranty applies only to products sold in Australia & New Zealand
Introduction
Welcome, and thank you for
choosing a Sharp facsimile!
The features and specifications of your new Sharp fax
are shown below.
Automatic dialling
Rapid Key Dialling: 8 numbers
Speed Dialling: 80 numbers
Imaging film
Initial starter film (included with fax
machine):
10 m roll (approx. 30 A4 pages)
Replacement film:
FO-3CR 30 m roll (two rolls in
package, one roll yields approx. 95 A4
pages)
Automatic document
feeder
10 sheets max.
Memory size*:
512 KB (approx. 30 pages with no voice
messages recorded and ECM turned off, or 24
minutes of voice messages (including OGMs)
with no documents in memory)
Modem speed
14400 bps with automatic fallback to lower
speeds.
Transmission time*
Approx. 6 seconds (only when ECM is on)
Reception modes
FAX, TEL, TEL/FAX, A.M.
Resolution
Horizontal:
8 lines/mm
Vertical:
Standard: 3.85 lines/mm
Fine/Halftone: 7.7 lines/mm
Super fine: 15.4 lines/mm
*Based on ITU-T Test Chart #1 at standard resolution, excluding time for protocol signals (i.e., ITU-T phase C time only).
1
Display
16-digit LCD display
Recording system
Thermal transfer recording
Halftone (greyscale)
64 levels (when sending)
Applicable telephone line Public switched telephone network
Compatibility
ITU-T (CCITT) G3 mode
Compression scheme
MH, MR, MMR
Scanning method
Sheet-feeder CIS (Contact Image Sensor)
Effective printing width
204 mm max.
Input document size
Automatic feeding:
Width: 148 to 210 mm
Length: 140 to 297 mm
Manual feeding:
Width: 148 to 210 mm
Length: 140 to 600 mm
Effective scanning width
210 mm max.
Contrast control
Automatic/Dark selectable
Copy function
Single/Multi-copy/Sort-copy (99 copies/page)
Telephone function
Standard (Cannot be used for incoming/
outgoing if power fails)
Power requirements
230-240 V AC, 50 Hz
Operating temperature
5 to 35°C
Humidity
Maximum: 85 %
Power consumption
Stand-by: 2.3 W
Maximum: 115 W
Dimensions
Width: 343 mm
Depth: 313 mm
Height: 312 mm
Weight
Approx. 3.4 kg
As a part of our policy of continuous improvement, SHARP reserves the right to make
design and specification changes for product improvement without prior notice. The
performance specification figures indicated are nominal values of production units.
There may be some deviations from these values in individual units.
2
Important safety information
• For your safety, if any of your equipment is not operating properly
or should any physical damage occur to the equipment where
internal parts may become exposed, the equipment should be
immediately disconnected from the phone line and then the power
line and returned to a SHARP authorised Service Centre for
inspection, repair, or disposal.
• In Australia, installing or modifying telephone lines should only be
done by an ACA licensed serviceman. In New Zealand, installing or
modifying telephone lines should be done in accordance with
Telecom wiring practices.
• Do not disassemble this machine or attempt any procedures not
described in this manual. Refer all servicing to qualified service
personnel.
• This machine must only be connected to a 230-240 V, 50 Hz,
earthed (3-prong) outlet. Connecting it to any other kind of outlet
may damage the machine.
• Do not install or use the machine near water, or when you are wet.
Take care not to spill any liquids on the machine.
• Unplug the machine from the telephone socket and then the power
outlet and consult a qualified service representative if any of the
following situations occur:
- Liquid has been spilled into the machine or the machine has been
exposed to rain or water.
- The machine produces odors, smoke, or unusual noises.
- The power cord is frayed or damaged.
- The machine has been dropped or the housing damaged.
• Do not allow anything to rest on the power cord, and do not install
the machine where people may walk on the power cord.
3
• Never insert objects of any kind into slots or openings on the
machine. This could create a risk of fire or electric shock. If an
object falls into the machine that you cannot safely remove, unplug
the machine and consult a qualified service representative.
• Do not place this machine on an unstable cart, stand or table. The
machine could be seriously damaged if it falls.
• Never install telephone wiring during a lightning storm.
• Never install telephone sockets in wet locations unless the socket is
specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
• Do not use a telephone to report a gas leak in the vicinity of the
leak.
• The socket-outlet must be installed near the equipment and must be
easily accessible.
Important:
• This facsimile machine is not designed for use on a line which has
call waiting, call forwarding, or certain other special services
offered by your telephone company. If you attempt to use the fax
machine on a telephone line using any of these services, you may
experience errors during transmission and reception of facsimile
messages.
• This facsimile machine is not compatible with digital telephone
systems.
• This facsimile machine is designed to operate in Australia and New
Zealand only.
4
WARNING NOTICE:
NO calls can be made to or from this fax during a mains power
failure.
WARNING - Australian Communications Authority (ACA)
regulations state that no unauthorised changes or modifications to this
equipment are permitted.
Note: Complies with ACA and NZ TELECOM standard AS/
NZS3548 regarding emission of electromagnetic interference.
These limits are designed to provide reasonable protection against
interference in an installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause interference. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a different circuit to that
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For Australia: The Ringer Equivalence Number (REN) for this
equipment is written on the back of the machine.The sum of all the
Ringer Equivalence Numbers (REN's) on your telephone line should
not exceed 3 to assure correct service from your telephone company.
5
IMPORTANT NOTICE FOR NEW ZEALAND USERS
Please note:
The grant of a Telepermit for any item of terminal equipment indicates
only that Telecom has accepted that the item complies with the
minimum conditions for connection to its network.
It indicates no endorsement of the product by Telecom, nor does it
provide any sort of warranty. Above all, it provides no assurance that
any item will work correctly in all respects with another item of
Telepermitted equipment of a different make or model, nor does it
imply that any product is compatible with all of Telecom's network
services.
This equipment shall not be set up to make automatic calls to the
Telecom '111' Emergency Service.
To avoid telephone charges for local calls, be sure to store numbers
without area code in your rapid or speed dial locations.
This equipment may not provide for the effective hand-over of a call
to another device connected to the same line.
All persons using this device for recording telephone conversations
shall comply with New Zealand law. This requires that at least one
party to the conversation is to be aware that it is being recorded. In
addition , the Principles enumerated in the Privacy Act 1993 shall be
complied with in respect to the nature of the personal information
collected, the purpose for its collection, how it is used and what is
disclosed to any other party.
6
Table of Contents
Introduction
1
Important safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important notice for new zealand users . . . . . . . . . . . . . . . . . . . . . . . 6
Table of Contents
7
1. Installation
9
Unpacking Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A Look at the Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Loading the Imaging Film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Loading Printing Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Entering Your Name and Fax Number . . . . . . . . . . . . . . . . . . . . . . 26
Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Selecting the Reception Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2. Using the Answering Machine
Recording an Outgoing Message . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating the Answering Machine . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Answering Machine Settings . . . . . . . . . . . . . . . . . . . . . . .
Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Override Ringing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. Sending Documents
Transmittable Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading the Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resolution and Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sending a Fax by Normal Dialling . . . . . . . . . . . . . . . . . . . . . . . . . .
Sending a Fax by Automatic Dialling . . . . . . . . . . . . . . . . . . . . . . . .
36
36
39
43
46
49
51
60
60
62
64
66
68
7
Table of Contents
4. Receiving Documents
77
Using TEL/FAX Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Using FAX Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Using A.M. Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Using TEL Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Substitute Reception to Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
5. Making Copies
85
6. Making Telephone Calls
88
7. Special Functions
91
Caller ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Distinctive Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Broadcasting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Cover Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Batch Page Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Blocking Reception of Unwanted Faxes . . . . . . . . . . . . . . . . . . . . . 105
Sending Documents From Memory . . . . . . . . . . . . . . . . . . . . . . . . 107
Polling (Requesting a Fax Transmission) . . . . . . . . . . . . . . . . . . . . 109
Timer Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
8. Option Settings
114
9. Printing Reports and Lists
121
10. Maintenance
128
11. Troubleshooting
132
Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Messages and Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Clearing Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
QUICK REFERENCE GUIDE
142
Index
144
8
1. Installation
1. Installation
Unpacking Checklist
Before setting up,
make sure you
have all of the
following items.
If any are missing,
contact your dealer
or retailer.
Original
document
support
Paper tray
extension
Handset
Rapid key
labels
Handset
lead
Operation
manual
Gears (4)
Telephone
line cord
Imaging film
(initial starter
roll)
Imaging film
cartridge
Adapter
(for Australia)
Adapter
(for New Zealand)
9
A Look at the Operation Panel
A Look at the Operation Panel
1
2
3
4
5
7
6
8
9 10
FACE DOWN
(MAX 10 SHEETS)
TEL FAX
TEL/FAX A.M.
ABC
1
GHI
JKL
7
3
MNO
4
PQRS
SPEED
DIAL
DEF
2
5
REDIAL
8
RECEPTION
MODE
VOLUME
DOWN
UP
RESOLUTION
FUNCTION
REC/MEMO PLAY/SKIP
DELETE
6
WXYZ
TUV
REPEAT
HOLD/
SEARCH
COPY/HELP
9
01
02
03
STOP
SPEAKER
0
04
05
06
07
08/POLL
START/MEMORY
11
12 13 14
15
16 17
18
19
1
SPEED DIAL key
Press this key to dial a 2-digit Speed Dial number.
2
REDIAL key
Press this key to automatically redial the last number dialled.
3
REPEAT key
Press this key to repeat playback of a message.
4
Display
This displays messages and prompts during operation and
programming.
5
PLAY/SKIP key
Press this key to play recorded messages. During playback, press it to
skip forward to the next message.
6
RECEPTION MODE key
Press this key to select the reception mode. An arrow in the display
will point to the currently selected reception mode.
10
7
RESOLUTION key
Press this key to adjust the resolution and contrast before sending or
copying a document.
8
VOLUME key
Press these keys to adjust the volume of the speaker when the
SPEAKER key has been pressed, or the volume of the ringer at all
other times.
9
FUNCTION key
Press this key to select various special functions.
10
Panel release
Grasp this finger hold and pull toward you to open the operation
panel.
11
Number keys
Use these keys to dial numbers, and enter numbers and letters during
number/name storing procedures.
12
HOLD/SEARCH key
Press this key to search for an automatic dialling number, or, during a
phone conversation, press this key to put the other party on hold.
13
SPEAKER key
Press this key to hear the line and fax tones through the speaker before
sending a document, or dialling a voice number.
Note: This is not a speakerphone. You must pick up the handset to
talk with the other party.
14
REC/MEMO key
Press this key to record a phone conversation or a message.
15
Rapid Dial keys
Press one of these keys to dial a fax or voice number automatically.
(Note that you must attach the Rapid Key labels.)
DELETE key
Press this key to erase recorded messages.
11
1. Installation
A Look at the Operation Panel
A Look at the Operation Panel
17
STOP key
Press this key to cancel operations before they are completed.
18
START/MEMORY key
Press this key to send or receive a document, or to scan a document
into memory before sending it.
19
COPY/HELP key
When a document is in the feeder, press this key to make a copy. At
any other time, press this key to print out the Help List, a quick
reference guide to the operation of your fax.
12
Connections
Points to keep in mind when setting up
Do not place the machine in
direct sunlight.
Do not place the machine near
heaters or air conditioners.
Keep dust away from the
machine.
Keep the area around the
machine clear.
About condensation
If the machine is moved from a cold to a warm place, it is possible that
condensation may form on the scanning glass, preventing proper
scanning of documents for transmission. To remove the condensation,
turn on the power and wait approximately two hours before using the
machine.
13
1. Installation
Connections
Connections
Handset
Connect the handset as shown and place it on the handset rest.
♦ The ends of the handset lead are identical, so they will go into either
socket.
Make sure the handset
lead goes into the
socket marked with a
handset symbol on the
side of the machine!
Use the handset to make
ordinary phone calls, or
to transmit and receive
documents manually.
14
Power lead
Plug the power lead into a 230-240 V, 50 Hz, earthed (3-prong) AC
outlet.
♦ Caution: When disconnecting the fax, unplug the telephone line
cord before unplugging the power lead.
♦ Caution: The mains outlet (socket outlet) should be installed near
the equipment and be easily accessable.
The machine does not have
a power on/off switch, so
the power is turned on and
off by simply plugging or
unplugging the power lead.
Note: If your area experiences a high incidence of lightning or power
surges, we recommend that you install surge protectors for the power and
telephone lines. Surge protectors can be purchased at most telephone specialty stores.
Moving your fax and reconnecting
Should it be necessary to move your fax to a new location, first
disconnect the telephone line cord before disconnecting the power
lead. When reconnecting, it is necessary to connect the power lead
before connecting the telephone line cord.
15
1. Installation
Connections
Connections
Telephone line cord
Insert one end of the telephone line cord into the adapter. Insert the
other end of the line cord into the socket on the back of the fax marked
TEL. LINE. Plug the adapter into the telephone socket on the wall.
TE
SEL. T
T EL
LI .
N
E
For Australia
For New Zealand
Be sure to insert the
telephone line cord into
the TEL. LINE socket.
Do not insert it into the
TEL. SET socket.
Comments:
♦ Your fax is set for tone dialling. If you are on a pulse only dial line,
you must set the fax for pulse dialling by changing Option Setting 7.
This procedure is described in Chapter 8, Option Settings.
♦ If you intend to use a computer fax modem on the same phone line,
you must reset Option Setting 10 (Fax Signal Receive) to NO in
order to prevent transmission and reception errors. This procedure
is described in Chapter 8, Option Settings.
16
Trays
Attach the paper tray extension.
♦ Pull the paper release plate forward. Insert the paper tray extension
horizontally into the notches in the paper tray. Rotate the paper tray
extension up until it snaps into place.
Attach the original document support.
Note: The original
document support
has a top side and a
bottom side. If you
cannot insert the
tabs on the support
into the holes, turn
the support over.
17
1. Installation
Connections
Connections
Extension phone (optional)
If desired, you can connect an extension phone to the TEL. SET
socket on the fax.
1
Remove the seal covering the TEL.
SET socket.
2
Connect the extension phone line to
the TEL. SET socket.
TE
SEL. T
T EL
LI .
NE
Important: In New Zealand, not all standard telephones and
answering machines will respond to incoming ringing when
connected to the extension socket of the equipment.
18
Loading the Imaging Film
Your fax uses a roll of imaging film to create printed text and images.
The print head in the fax applies heat to the imaging film to transfer
ink to the paper. Follow the steps below to load or replace the film.
The initial starter roll of
imaging film included with
your fax can print about
30 A4 pages.
When replacing the film, use a
roll of Sharp FO-3CR imaging
film. One roll can print about
95 A4 pages.
Note: If there is paper in the paper tray, pull the paper release plate forward and remove the paper before loading the imaging film.
1
Open the operation panel by grasping the finger hold and pulling up.
2
Pull the green release on the right side of the machine forward, and
open the print compartment cover.
19
1. Installation
Loading the Imaging Film
Loading the Imaging Film
If you are installing the imaging film for the
first time, go to Step 6.
3
Remove the imaging film cartridge from the print compartment (grasp
the handle at the front of the cartridge) and turn it over.
4
Remove the used film from the cartridge.
5
Remove the four green gears from the used film.
DO NOT DISCARD THE FOUR GREEN GEARS!
20
6
Remove the new roll of imaging film from its packaging.
• Do not yet remove the band that holds the rolls together.
7
Insert the large gear into the green end of the empty spool. Make sure
the two protrusions on the large gear fit firmly into the slots in the end
of the spool.
Insert the remaining three gears into the spools, making sure the
protrusion on each gear fits firmly into one of the slots in the end of
each spool.
• If needed, pull the spools apart slightly to allow the gears to fit (the
band will stretch).
Protrusion
Slot
Large gear
21
1. Installation
Loading the Imaging Film
Loading the Imaging Film
8
Insert the large gear into the large holder on the imaging film cartridge
(make sure it clicks into place), and then insert the small gear on the
other end of the spool into its holder.
9
Cut the band that holds the two spools together. Unroll the film slightly
and insert the small gears into their holders.
10
22
Turn the cartridge over, grasp the handle, and insert the cartridge into
the print compartment.
11
Rotate the large gear toward you until the film is taut.
12
Close the print compartment cover (press down on both sides to make
sure it clicks into place), and then close the operation panel.
Click!
13
Load paper in the paper tray and then press the following keys to
initialize the film.
Note: Paper must be loaded before the film can be initialized. To load
paper, see the following section, Loading Printing Paper.
Display shows:
FUNCTION
6
INITIALIZE FILM
START/MEMORY
When to replace the imaging film
Replace the imaging film when the display shows:
FILM END
Use the following imaging film, which is available from your dealer
or retailer:
Sharp FO-3CR Imaging Film
23
1. Installation
Loading the Imaging Film
Loading Printing Paper
Loading Printing Paper
You can load A4 size paper in the paper tray. The maximum number
of sheets is:
♦ 60 for paper from 60 to 75 g/m2
♦ 50 for paper from 75 to 90 g/m2
1
Fan the paper, and then tap the edge against a flat surface to even the
stack.
2
Pull the paper release plate toward you.
3
Insert the stack of paper into the tray, print side down.
• If paper remains in the tray, take it out and combine it into a single
stack with the new paper before adding the new paper.
Be sure to load the paper
so that printing takes place
on the print side of the
paper. Printing on the
reverse side will result in
poor print quality.
24
4
Push the paper release plate back down.
If the paper release plate is
not pushed down, paper
feed errors will result.
Note: When receiving faxes or copying documents, do not allow a large
number of pages to accumulate in the output tray. This may obstruct the
outlet and cause paper jams.
Note: If the display shows the following alternating messages when
making a copy or receiving a fax, check the paper tray. If the tray is
empty, add paper and then press the START/MEMORY key. If there is
paper, make sure it is inserted correctly and then press the START/
MEMORY key.
PRESS START KEY
SET PAPER &
5
Your fax has been set at the factory to print at normal contrast.
Depending on the type of paper you have loaded, you may find that you
obtain better print quality by changing the setting to LIGHT. Press these
keys:
FUNCTION
6
The display will show:
PRINT CONTRAST
Press 1 to select NORMAL or 2 to select LIGHT.
NORMAL
1
The display will show:
LIGHT
or
2
COPY CUT-OFF
Press the STOP key to return to the date and time display.
STOP
25
1. Installation
Loading Printing Paper
Entering Your Name and Fax Number
Entering Your Name and Fax Number
Before you can begin using
your fax, you need to enter
your name and the
telephone number of your
fax. You also need to set
the date and time.
Once you enter this
information, it will
automatically appear
at the top of each fax
page you send.
3 key
1
2
3
4
5
6
8
9
7
FUNCTION key
START/MEMORY
key
0
# key
STOP key
Note: The imaging film and printing paper must be loaded before your name
and fax number can be entered.
1
2
Press these keys:
FUNCTION
The display will show:
ENTRY MODE
Press the # key twice:
The display will show:
26
3
OWN NUMBER SET
3
Press the START/MEMORY key.
START/MEMORY
The display will show:
4
ENTER FAX #
Enter your fax number by pressing the number keys. Up to 20 digits can
be entered.
• To insert a space between digits, press the # key. To insert a "+", press
the * key.
• If you make a mistake, press the HOLD/SEARCH key to move the
cursor back to the mistake and then enter the correct number. The
new number will replace the old number.
Example:
5
5
5
1
2
3
4
Cursor: A dark square mark in the display that indicates where a number or
letter will be entered.
5
Press the START/MEMORY key to enter the fax number in memory.
START/MEMORY
The display will show:
6
ENTER YOUR NAME
Enter your name by pressing the number keys as shown in the following
chart. Up to 24 characters can be entered.
♦ To enter two letters in succession that require the same key, press
the SPEAKER key after entering the first letter to advance the
cursor.
Example: SHARP = 77777 444 22 7777
SPEAKER
77
27
1. Installation
Entering Your Name and Fax Number
Entering Your Name and Fax Number
A=
J=
B=
K=
T=
C=
L=
U=
D=
M=
V=
E=
N=
W=
F=
O=
X=
G=
P=
Y=
H=
Q=
Z=
I=
R=
SPACE =
GHI
ABC
DEF
JKL
MNO
S=
SPEED DIAL
REDIAL
PQRS
TUV
WXYZ
HOLD/
SEARCH
SPEAKER
Press this key to delete the
letter highlighted by the
cursor.
Press this key to change
case.
Press this key to move the
cursor to the left.
Press this key to move the
cursor to the right.
Press either key repeatedly to select
one of the following symbols:
./!"#$%&'()++,-:;<=>?@[ ¥]^_'{|}→←
7
Press the START/MEMORY key to save your name in memory.
START/MEMORY
The display will show:
8
SECURITY SELECT
Press the STOP key to return to the date and time display.
STOP
28
Setting the Date and Time
The date and time appear
in the display and reports,
and are printed at the top of
every page you fax.
3 key
1
2
3
4
5
6
8
9
7
* key
FUNCTION key
START/
MEMORY key
0
STOP key
Note: The imaging film and printing paper must be loaded before the date
and time can be set.
1
2
Press these keys:
FUNCTION
The display will show:
ENTRY MODE
3
Press the * key three times.
The display will show:
DATE & TIME SET
29
1. Installation
Setting the Date and Time
Setting the Date and Time
3
Press the START/MEMORY key.
START/MEMORY
• The currently set date will appear in the display.
4
Enter a two-digit number for the day ("01" to "31").
• To correct a mistake, press the SPEED DIAL key to move the cursor
back to the mistake, and then enter the correct number.
Example: the 5th
5
1
2
0
0
1
Enter a two-digit number for the hour ("00" to "23") and a two-digit
number for the minute ("00" to "59").
Example: 9:25
30
0
Enter the year (four digits).
Example: 2001
7
5
Enter a two-digit number for the month ("01" for January, "02" for
February, "12" for December, etc.).
Example: January
6
0
0
9
2
5
8
Press the START/MEMORY key to start the clock.
START/MEMORY
The display will show:
9
STORE JUNK #
Press the STOP key to return to the date and time display.
STOP
31
1. Installation
Setting the Date and Time
Selecting the Reception Mode
Selecting the Reception Mode
Your fax machine has four modes for receiving incoming calls and
faxes:
TEL mode:
This mode is the most convenient for receiving phone calls. Faxes can
also be received; however, all calls must first be answered by picking
up the fax's handset or an extension phone connected to the same line.
FAX mode:
Select this mode when you only want to receive faxes on your line.
The fax machine will automatically answer all calls and receive
incoming faxes.
TEL/FAX mode:
This mode is convenient for receiving both faxes and voice calls.
When a call comes in, the fax will detect whether it is a voice call
(including manually dialled fax transmissions), or an automatically
dialled fax. If it is a voice call, the fax will make a special ringing
sound to alert you to answer. If it is an automatically dialled fax
transmission, reception will begin automatically.
A.M. mode:
Select this mode when you are out and want the built-in answering
machine to answer all calls. Voice messages will be recorded, and fax
messages will be received automatically.
32
Setting the reception mode
Press the RECEPTION MODE key until the arrow in the display
points to the desired mode.
RECEPTION MODE key
1
2
3
4
5
6
8
9
7
0
TEL
FAX
14 OCT 10:30
TEL/FAX A.M.
TEL
RECEPTION
MODE
FAX
14 OCT 10:30
TEL/FAX A.M.
TEL
FAX
14 OCT 10:30
TEL/FAX A.M.
TEL
FAX
14 OCT 10:30
TEL/FAX A.M.
Note: A.M. mode cannot be selected unless a general outgoing message
has been recorded as explained in Chapter 2.
For more information on receiving faxes in TEL, TEL/FAX and FAX
modes, see Chapter 4, Receiving Documents. For more information on
using A.M. mode, see Chapter 2, Using the Answering Machine.
33
1. Installation
Selecting the Reception Mode
Volume Adjustment
Volume Adjustment
You can adjust the
volume of the speaker
and ringer using the UP
and DOWN keys.
DOWN key
1
2
3
4
5
6
8
9
7
UP key
0
SPEAKER key
Speaker
1
Press the SPEAKER key.
2
Press the UP or DOWN key.
3
34
When the display shows the desired
volume level, press the SPEAKER
key to turn off the speaker.
SPEAKER
DOWN
or
SPEAKER
UP
Ringer
1
Press the UP or DOWN key. (Make
sure the SPEAKER key has not been
pressed.)
DOWN
or
UP
♦ The ringer will ring once at the
selected level, then the date and
time will reappear in the display.
2
Display:
RINGER: HIGH
RINGER: MIDDLE
RINGER: LOW
RINGER OFF: OK?
If you selected RINGER OFF: OK ?,
press the START/MEMORY key.
START/MEMORY
Note: When the reception mode is set to TEL, the ringer will still ring at
Low if turned off.
Silent ring fax detection system
You can also set your fax machine to receive faxes silently, but ring to
alert you to a voice call. To do so, set the ringer volume to OFF and set
the reception mode to TEL/FAX. When a voice call comes in, a
special ringer on the fax will ring. Note that extension telephones will
not ring.
Note: During intial ringing before the fax picks up the call, the fax will
be silent but extension telephones will ring.
35
1. Installation
Volume Adjustment
2. Using the Answering Machine
The FO-885's built-in answering machine allows you to receive both
voice messages and fax transmissions while you are out.
To use the answering
machine, record an
outgoing message and then
set the reception mode to
A.M. when you go out.
Recording an Outgoing Message
The outgoing message (OGM) is the greeting that the machine plays
after answering a call to inform callers that they can leave a message
or send a fax.
Example:
"Hello. You've reached the ABC company. No one is available to take
your call right now. Please leave a message after the beep or press
your facsimile Start key to send a fax. Thank you for calling."
1
Press these keys:
FUNCTION
0
The display will show: A.M. SETTINGS
2
Press the # key.
The display will show:
36
OGM RECORDING
Recording an Outgoing Message
Press the START/MEMORY key.
START/MEMORY
4
5
Press 1 to select GENERAL. (If you
are recording a message for the
Transfer function explained later in
this chapter, press 2 for TRANSFER.)
GENERAL TRANSFER
1
or
2
Pick up the handset, press the
START/MEMORY key, and speak
into the handset.
• The outgoing message can be up to
60 seconds long. The outgoing
message for the Transfer function
can be up to 15 seconds long.
START/MEMORY
• While recording, the display will
show the time remaining to record.
6
7
When finished, press the STOP key
and then replace the handset.
Press the STOP key twice to return to
the date and time display.
STOP
STOP
STOP
37
2. Answering
Machine
3
Recording an Outgoing Message
To listen to the outgoing message
To listen to the outgoing message, follow Steps 1 through 4 of the above
procedure to select the message, and then press the PLAY/SKIP key to
listen to it. To return to the date and time display, press the STOP key
twice. Note that the general outgoing message cannot be erased. If you
need to change it, simply repeat the recording procedure. (The Transfer
message can be deleted by pressing the DELETE key after selecting it as
explained above.)
38
Operating the Answering Machine
Operating the Answering Machine
2. Answering
Machine
Activating the answering machine
Activate the answering machine before you go out as follows:
Press the RECEPTION MODE key
until the arrow in the display points to
A.M..
RECEPTION
MODE
• The outgoing message will play
(you can stop playback by pressing
the STOP key).
TEL
• It will not be possible to set the
reception mode to A.M. if a general
outgoing message has not been
recorded.
FAX
TEL/FAX A.M.
When the reception mode is set to A.M., the FO-885 will answer
incoming calls after two rings if it has received at least one incoming
message, or after four rings if no messages have been received. (For
more information, see Toll Saver in Remote Operations in this
chapter.)
Note: If the memory is full from messages previously recorded,
MEMORY IS FULL will appear in the display. To set the reception mode
to A.M., you must first erase some or all of the stored messages.
Note: In A.M. mode, the machine will automatically switch to fax
reception if it detects a period of silence longer than six seconds after
answering a call. For this reason, if a caller pauses for this length of time
while leaving a message, they will be cut off.
39
Operating the Answering Machine
Listening to received messages
When you return, the display will show the number of messages
recorded. Listen to the messages as follows:
1
Press the PLAY/SKIP key.
• If you only want to listen to new
messages (messages not previously
listened to), continue to hold the
PLAY/SKIP key down for at least
two seconds.
2
PLAY/SKIP
The messages will play.
• As each message plays, the date
and time of recording will appear
briefly in the display. If no
messages were received, NO
MESSAGES will appear.
• To listen to a message a second
time, press the REPEAT key
before playback of that message
ends.
• To move back to the previous
message, press the REPEAT key
within 3 seconds of the beginning
of the current message.
• To skip forward to the next
message, press the PLAY/SKIP
key.
REPEAT
REPEAT
PLAY/SKIP
Note: Playback will stop if you receive a call, lift the handset, or press
the STOP key.
40
Operating the Answering Machine
Erasing received messages
• Erasing all messages: To erase all
messages, press and hold down the
DELETE key for at least 2
seconds.
2. Answering
Machine
It is important to erase received messages after you listen to them to
ensure that the memory does not become full.
DELETE
• Erasing a single message: To
erase only a single message, press
the DELETE key while the
message is being played.
Using the REC/MEMO key
You can use the REC/MEMO key to record telephone conversations
and messages for other users of the FO-885. These will be played back
together with any incoming messages when the PLAY/SKIP key is
pressed.
• Recording messages: To record a
message, press the REC/MEMO
key for at least 1 second, and then
pick up the handset, press the
START/MEMORY key, and speak
into the handset. When you have
finished speaking, replace the
handset or press the STOP key.
REC/MEMO
• Recording phone conversations:
To record a phone conversation,
hold down the REC/MEMO key
during the conversation you want to
record (while recording, you will
hear a beep every 15 seconds).
When you are finished, release the
key.
41
Operating the Answering Machine
Date and time of ICMs
You can check the date and time of your received messages by
pressing the panel keys as shown below.
♦ The dates and times are also shown in the Message List, which can
be printed out as described in Chapter 9.
1
The display will show:
2
4
0
A.M. SETTINGS
Press these keys:
The display will show:
3
FUNCTION
Press these keys:
ICM CONFIRMATION
Press the START/MEMORY key.
The number of messages recorded
will appear in the display.
Press # or * one or more times to
show the date and time of each of the
messages.
START/MEMORY
or
• The message number will appear
first, and then the date and time
several seconds later.
5
Press the STOP key.
STOP
Note: The recorded dates and times are cleared each time you erase the
messages.
42
Optional Answering Machine Settings
Optional Answering Machine Settings
Incoming messages (ICMs) are the messages which callers leave for
you on the built-in answering machine. The answering machine is set
at the factory to allow each caller a maximum of 4 minutes to leave a
message. If desired, you can change this setting to 15, 30, or 60
seconds.
1
Press these keys:
FUNCTION
0
The display will show:
2
Press these keys:
The display will show:
3
4
A.M. SETTINGS
ICM RECORD TIME
Press a numeric key to select the
desired ICM recording time:
• 1: 15 seconds
1
• 2: 30 seconds
2
• 3: 60 seconds
3
• 4: 4 minutes
4
Press the STOP key.
STOP
43
2. Answering
Machine
Setting ICM time
Optional Answering Machine Settings
Fax reception on TAD failure
If the memory for recording incoming messages becomes full while
you are out, the answering machine will no longer be able to record
messages. The ON A.M. FAILURE setting is used to choose the
response of the machine to incoming calls when this happens:
♦ Automatic fax reception NO: The FO-885 will answer after 20
rings, after which it will wait to receive a remote command. Most
callers will hang up before it answers; however, when you call the
FO-885 from a remote location, you can wait until it answers, listen
to your messages, and then erase them (see Remote Operations in
this chapter).
♦ Automatic fax reception YES: The reception mode will switch to
FAX mode, allowing the FO-885 to continue to receive faxes
automatically without broadcasting an OGM on answering. With
this setting, you can still use the remote commands to listen to your
messages and erase the message memory (see Remote Operations
in this chapter).
Automatic fax reception is set to NO at the factory before shipping. If
you want to set it to YES, press the panel keys as follows:
1
The display will show:
2
0
A.M. SETTINGS
Press these keys:
The display will show:
44
FUNCTION
Press these keys:
ON A.M. FAILURE
3
Press 1 to turn automatic fax
reception on, or 2 to turn it off.
4
Press the STOP key.
1
or
STOP
2
Optional Answering Machine Settings
OGM only mode
1
Press these keys:
2. Answering
Machine
If needed, you can turn off recording of incoming messages. In this
case, your outgoing message will play, but callers will not be able to
leave a message. (The machine will still receive faxes sent by
automatic dialling.)
FUNCTION
0
The display will show: OGM ONLY MODE
2
Press 1 to turn on OGM only mode, or
2 to turn it off.
3
Press the STOP key.
1
or
2
STOP
45
Transfer Function
Transfer Function
The Transfer function is used to make the FO-885 automatically call
you at a specified number every time it receives an incoming message.
This lets you hear your messages immediately after they come in,
even when you are at a remote location.
When you answer the telephone, you will hear your recorded message
telling you that the call is a transfer call. Enter "#", your remote code
number, and "#". The answering machine will then play back your
messages. You can also perform any of the remote operations
described in the previous section.
Note: When you hang up after a transfer call, the FO-885 will not
immediately resume normal operation. If you want the FO-885 to accept
calls immediately after a transfer call, enter "*" twice before hanging up
(if you want to hang up during message playback, first enter "0" and " #"
to stop playback, then enter "*" twice).
Programming the transfer number
To use the Transfer function, you must first give the FO-885 the
number to call (the transfer number). This is done by pressing the
panel keys as follows:
1
Press these keys:
The display will show:
2
0
A.M. SETTINGS
Press these keys:
The display will show:
46
FUNCTION
TRANSFER # ENTRY
Transfer Function
Press the START/MEMORY key.
START/MEMORY
4
Enter a transfer number (max. of 32
digits including pauses) by pressing
the number keys.
5
5
5
1
2
3
5
(Example)
• To insert a pause between any two
digits of the number, press the
REDIAL key.
5
Press the START/MEMORY key
and then the STOP key.
STOP
START/MEMORY
Recording the transfer message
The transfer message plays when you answer the telephone, and
informs you that the call is a transfer call. It can be up to 15 seconds
long. To record a transfer message, follow the steps described in
Recording an Outgoing Message in this chapter. The following is an
example:
"Hello. This is a transfer call for (YOUR NAME). Enter your remote
code number now."
47
2. Answering
Machine
3
Transfer Function
Turning the Transfer function on and off
1
The display will show:
2
0
A.M. SETTINGS
Press these keys:
The display will show:
48
FUNCTION
Press these keys:
TRANSFER FUNC
3
Press 1 to turn the Transfer function
on, or 2 to turn it off.
4
Press the STOP key.
1
or
STOP
2
Override Ringing
This function allows selected callers using a tone dial telephone to
override the answering machine's outgoing message and cause the
FO-885 to make a special ringing sound, alerting you that they are
calling. This is useful when you are near the machine but only want to
talk with certain callers, taking all other calls on the answering
machine.
Programming the override code
To override the answering machine, your callers must enter a 3-digit
override code from their telephone. This code has been set to "009" at
the factory. If you want to change it, press the panel keys as shown
below.
Important!
♦ Make sure the override code is different from the remote code used
for remote operations.
1
The display will show:
2
4
0
A.M. SETTINGS
Press these keys:
The display will show:
3
FUNCTION
Press these keys:
OVERRIDE CODE
Enter a 3-digit code number by
pressing the number keys.
Press the START/MEMORY key and
then the STOP key.
5
5
4
(Example)
STOP
START/MEMORY
49
2. Answering
Machine
Override Ringing
Override Ringing
Overriding the answering machine
Your callers should follow the steps below to override the answering
machine.
1
Your caller calls the FO-885 from a
tone dial telephone. When the
outgoing message begins, they should
press the "#" key on their telephone.
• The caller will hear a short beep,
and the outgoing message will stop.
2
The caller should enter the override
code and "#" by pressing the
appropriate keys on their telephone.
• If an incorrect code is entered, the
caller will hear four beeps. He or
she must re-enter the correct code
within 10 seconds or the line will
be disconnected.
3
The FO-885 will make a special
ringing sound. Pick up the handset to
answer the call. (Note that an
extension telephone connected to the
same line will not ring.)
• If you do not answer within 30
seconds, the outgoing message will
play again and the caller can then
leave a message.
50
5
5
4
(Example)
Remote Operations
Remote Operations
2. Answering
Machine
You can call the FO-885 from any tone dial telephone and play back
your messages using the remote commands. You can also use these
commands to change the reception mode and other settings.
Remote code number
To perform remote operations, you must first program a remote code
number. This number is used to prevent unauthorised people from
listening to your messages or changing the settings of your machine.
The remote code number has been set to "001" at the factory. If you
want to change it, press the panel keys as shown below.
1
The display will show:
2
4
0
A.M. SETTINGS
Press these keys:
The display will show:
3
FUNCTION
Press these keys:
REMOTE CODE
Enter a 3-digit number by pressing the
number keys.
2
2
2
(Example)
STOP
Press the START/MEMORY key and
then the STOP key.
START/MEMORY
51
Remote Operations
Toll Saver
When you call the FO-885 to listen to your messages, it will answer
after two rings if it has received at least one message, or after four
rings if it has not received any messages.
This allows you to save money on telephone charges, particularly if
you are calling long distance. If the machine does not answer after the
second ring, you can simply hang up before it answers, saving
yourself the cost of that call.
If you do not want to use the Toll Saver function, you can turn it off by
following the steps below. In this case, the FO-885 will answer after
the number of rings set with Option Setting 2 (see Chapter 8), the ring
setting for FAX reception mode.
1
The display will show:
2
0
A.M. SETTINGS
Press these keys:
The display will show:
52
FUNCTION
Press these keys:
TOLL SAVER
3
Press 1 to turn Toll Saver on, or 2 to
turn it off.
4
Press the STOP key.
1
or
STOP
2
Remote Operations
Retrieving your messages
1
2. Answering
Machine
Note: You can also access the FO-885 for remote operation when the
reception mode is set to FAX or TEL/FAX. In this case, call the FO-885,
press the "#" key immediately after it answers, or during pseudo ringing
in TEL/FAX mode (before you hear the fax tone in either case), and then
continue from Step 2 below.
Call the FO-885 from a touch-tone
telephone. When your outgoing
message begins, press the "#" key on
the telephone.
• You will hear a short beep, and the
outgoing message will stop.
2
Enter your remote code number and
then # by pressing the keys on the
telephone.
2
2
2
(Example)
• You will hear a series of beeps
equal to the number of messages
recorded, or one long beep if four
or more messages have been
received. The machine will then
play back the messages, beeping
once at the end of each message.
When all messages have been
played back, you will hear a long
beep.
• If no messages have been received,
you will hear a short beep. You can
either hang up, or perform any of
the operations described in the
following section Other remote
operations.
53
Remote Operations
3
While the messages are playing, you
can do any of the following:
• Repeat: To listen to a message a
second time, press "2" and "#" on
the telephone before that message
ends. To move back to the previous
message, press "2" and "#" within
the first 3 seconds of the current
message.
2
• Skip forward: To skip forward to
the next message, press "5" and "#"
on the telephone.
5
• Stop: To stop playback, press "0"
and "#" on the telephone. After this,
you can enter any of the commands
described in the following section,
"Other remote operations".
• Play new messages: To listen to
only your new messages, first stop
playback by pressing "0" and "#",
and then press "6" and "#".
0
0
• Erase a message: To erase the
message you are currently listening
to, press "3" and "#" before it ends.
4
3
When you have finished listening to
your messages, you can do any of the
following:
• Erase all messages: To erase all of
your messages, press "3", "3", and
"#".
54
6
3
3
Remote Operations
• Repeat playback: To listen to your
messages again, press "7" and "#".
7
2. Answering
Machine
• Perform other operations: You
can enter any of the commands
described in the following section,
Other remote operations.
• Hang up: If you do not erase your
messages first, they will be saved
and any new messages will be
recorded after them. If you want the
FO-885 to resume normal operation
immediately, press "*" twice
before hanging up (in some cases,
particularly when the Transfer
function is used, the FO-885 may
not accept new calls for one or two
minutes after you hang up unless
you first press "*" twice).
Comments:
♦ When a remote command is accepted by the machine, you will hear
one beep. If an incorrect command is entered, you will hear four
beeps. In the latter case, re-enter the correct command.
♦ When entering a command, do not pause longer than 10 seconds
between each digit. If you do, a 4-beep error signal will be issued
and the digits entered up to that point will be disregarded. In this
case, re-enter the command from the beginning.
♦ If you make two errors (causing two 4-beep signals to be issued)
while entering your remote code number, the line will be
disconnected. This prevents unauthorized people from attempting
to guess your remote code number.
♦ If you pause for longer than 10 seconds before entering a command,
you will be disconnected.
55
Remote Operations
Other remote operations
After listening to your messages, you can do any of the operations
described below by pressing the appropriate keys on the telephone.
Note: The following commands cannot be entered while messages are
being played back. If you do not want to wait until playback ends to enter
a command, first stop playback by pressing "0" and "#", and then enter
the command.
Changing the fax reception mode
Select a new reception mode by
pressing the keys as follows:
• A.M. mode: "8", "1", and "#".
8
• FAX mode: "8", "2", and "#".
(Example)
• TEL mode: "8", "3", and "#".
Caution: In TEL mode, you will
not be able to further change the
reception mode.
• TEL/FAX mode: "8", "4", and "#".
Recording a new outgoing message
1
56
Press "4" and "*" on the telephone.
1
4
Remote Operations
When you hear a short beep, speak
into the telephone to record the new
message.
2. Answering
Machine
2
• The message can be up to 15
seconds long. After 15 seconds (or
earlier if the machine detects
silence after you finish speaking),
you will hear a beep, and the new
message will be played back.
Turning the Transfer function on or off
To turn Transfer on: Press "9", "1",
and "#" on the telephone.
9
1
(Example)
To turn Transfer off: Press "9", "2",
and "#" on the telephone.
Changing the transfer telephone number
1
Press "9", "0", and "#" on the
telephone.
2
After you hear a short beep, enter the
new telephone number. When
5 4
finished, press "#".
• To insert a pause between any two
digits of the number, press "*".
9
6
0
1
1
3
4
(Example)
57
Remote Operations
Recording a new transfer message
1
Press "9", "3", and "#" on the
telephone.
2
When you hear a short beep, speak
into the telephone to record the new
message.
9
3
• The time for the transfer message is
fixed at 15 seconds. After 15
seconds (or earlier if the machine
detects silence after you finish
speaking), you will hear a beep, and
the new message will be played
back automatically.
Recording a "Memo"
You can record a "memo" for yourself or other users of the FO-885.
The memo will be played back when incoming messages are listened
to.
1
Press "*" and "#" on the telephone.
2
When you hear a short beep, speak
into the telephone to record the
memo.
3
When you are finished, press "0" and
"#".
• If the FO-885 detects a certain
period of silence, it will stop
recording automatically.
58
0
Remote Operations
To turn on OGM only mode, press
"1", "1", and "#". (Your outgoing
message will play, but callers will not
be able to record a message. Faxes
sent by automatic dialling will be
received).
To turn off OGM only mode, press
"1", "2", and "#".
1
1
1
2
2. Answering
Machine
OGM only mode
59
3. Sending Documents
Transmittable Documents
Size and weight
The size and weight of documents that you can load in the document
feeder depend on whether you load one page at a time or several pages
at once.
Loading one page at a time:
210 mm
Minimum
size
Maximum
size
148 mm
600 mm
140 mm
Minimum
weight
Maximum
weight
52 g/m²
157 g/m²
Loading several pages at once:
Minimum
size
210 mm
148 mm
Maximum
size
140 mm
Minimum
weight
Maximum
weight
52 g/m²
60
297 mm
80 g/m²
Transmittable Documents
Note: Letters or graphics on the edges of a document will not be
scanned.
3. Sending
Documents
Letters in the
shaded area will
not be scanned.
5 mm
4 mm
4 mm
5 mm
Other restrictions
♦ The scanner cannot recognise yellow, greenish yellow, or light blue
ink.
♦ Ink, glue, and correcting fluid on documents must be dry before
they pass through the document feeder.
♦ All clips, staples, and pins must be removed from documents before
loading in the feeder. If these are not removed, they may damage the
machine.
♦ Documents which are patched, taped, torn, smaller than the
minimum size, carbon backed, easily smudged, or have a slippery
coated surface should be photocopied, and the copy loaded in the
feeder.
61
Loading the Document
Loading the Document
Up to 10 pages can be placed in the feeder at one time. The pages will
automatically feed into the machine starting from the bottom page.
♦ If you need to send or copy more than 10 pages, place the additional
pages gently and carefully in the feeder just before the last page is
scanned. Do not try to force them in, as this may cause doublefeeding or jamming.
♦ If your document consists of several large or thick pages which
must be loaded one at a time, insert each page into the feeder as the
previous page is being scanned. Insert gently to prevent doublefeeding.
1
Adjust the document guides to the
width of your document.
2
Place the document face down and
push it gently into the document
feeder. The top edge of the document
should enter the machine first.
• The feeder will draw the leading
edge of the document into the
machine. The display will show:
READY TO SEND
3
62
Adjust the resolution and/or contrast
setting (if desired) as explained in the
section Resolution and Contrast, then
dial the receiving machine as
explained in Sending a Fax by
Normal Dialling.
RESOLUTION
Loading the Document
Removing a document from the feeder
Important!
Do not try to remove a document without opening the operation panel.
This may damage the feeder mechanism.
1
Open the operation panel by grasping
the finger hold and pulling up.
2
Remove the document.
3
Close the operation panel, making
sure it clicks into place.
Click!
63
3. Sending
Documents
If you need to remove a
document from the feeder,
open the operation panel.
Resolution and Contrast
Resolution and Contrast
If desired, you can adjust the resolution and contrast before sending a
document.
The default resolution
setting is STANDARD
and the default contrast
setting is AUTO.
You must adjust the
settings each time you
don't want to use the
default settings.
Note: The resolution and contrast settings are only effective for transmitting
a document. They are not effective for receiving a document.
Resolution settings
STANDARD
Use STANDARD for ordinary documents.
This setting gives you the fastest and most
economical transmission.
FINE
Use FINE for documents containing small
letters or fine drawings.
SUPER FINE
Use SUPER FINE for documents containing
very small letters or very fine drawings..
HALF TONE
Use HALF TONE for photographs and
illustrations. The original will be reproduced
in shades of grey.
Contrast settings
64
AUTO
Use AUTO for normal documents.
DARK
Use DARK for faint documents.
Resolution and Contrast
1
Load the document(s).
• The document must be loaded
before the resolution and contrast
can be adjusted.
RESOLUTION
Press the RESOLUTION key one or
more times until the desired
resolution and contrast settings
appear in the display.
• The first time you move through
the list of resolution settings, the
contrast setting AUTO will appear
next to each resolution setting. The
second time you move through the
list, the contrast setting DARK will
appear.
3. Sending
Documents
2
Display:
STANDARD
:AUTO
FINE
:AUTO
SUPER FINE
:AUTO
HALF TONE
:AUTO
STANDARD
:DARK
FINE
:DARK
SUPER FINE
:DARK
HALF TONE
:DARK
Note: In order to transmit in FINE or SUPER FINE resolution, the receiving
fax machine must also have that resolution. If it doesn't, your machine will
automatically step down to the next best available setting.
65
Sending a Fax by Normal Dialling
Sending a Fax by Normal Dialling
With Normal Dialling, you pick up the handset (or press the
SPEAKER key) and dial by pressing the number keys.
♦ If a person answers, you can talk with them through the handset
before sending the fax. (If you pressed the SPEAKER key, you
must pick up the handset to talk.)
♦ Normal Dialling allows you to listen to the line and make sure the
other fax machine is responding.
1
Load the document(s).
The display will show:
READY TO SEND
• Set the resolution and/or contrast if
desired.
2
3
RESOLUTION
Pick up the handset or press the
SPEAKER key. Listen for the dial
tone.
Dial the number of the receiving
machine by pressing the numeric
keys.
SPEAKER
or
ABC
1
GHI
4
PQRS
7
66
2
JKL
5
TUV
8
DEF
3
MNO
6
WXYZ
9
Sending a Fax by Normal Dialling
4
Wait for the connection. Depending
on the setting of the receiving
machine, you will either hear a
facsimile reception tone or the other
person will answer.
Beep
5
When you hear the reception tone,
press the START/MEMORY key.
Replace the handset if you used it.
3. Sending
Documents
• If the other party answers, (lift the
handset if the SPEAKER key was
pressed) ask them to press their
START key. This causes the
receiving machine to issue a
reception tone.
START/MEMORY
• When transmission is completed,
the fax will beep once.
Using the REDIAL key
You can press the REDIAL key to redial the last number dialled. To
send a document, proceed from Step 4 of Normal Dialling. Note that
the speaker will be automatically activated when you press the
REDIAL key.
Facsimile reception tone: This is a pronounced, high-pitched tone
that the receiving machine sends to the transmitting machine to
indicate that it is ready to receive.
67
Sending a Fax by Automatic Dialling
Sending a Fax by Automatic Dialling
You can dial a fax or telephone number by simply pressing a Rapid
Key, or by pressing the SPEED DIAL key and entering a two-digit
number.
♦ To use Automatic Dialling, you must first store the full fax or
telephone number in your fax machine.
♦ When you store a fax or telephone number, you select a two-digit
Speed Dial number for it. 88 Speed Dial numbers are available.
Speed Dial numbers 01
through 08 are for
Rapid Key (one-touch)
Dialling.
01
SPEED
DIAL
Speed Dial numbers 09
through 88 are for
dialling with the
SPEED DIAL key.
1
1
START/MEMORY
SPEED DIAL key
Attach the strip
of Rapid Key
labels above the
Rapid Keys.
1
2
3
4
5
6
8
9
7
0
Rapid Keys
When you store a
number in a Rapid
Key, write the name of
the party on the label.
68
Sending a Fax by Automatic Dialling
Storing fax and telephone numbers for Automatic Dialling
1
Press these keys:
FUNCTION
3
2
FAX/TEL # MODE
Press 1 to select SET.
The display will show:
3. Sending
Documents
The display will show:
1
FAX/TEL # SET
ENTER SPEED #
3
Enter a two-digit Speed Dial number by pressing the number keys (01
to 08 for Rapid Key Dialling, 09 to 88 for Speed Dialling).
0
4
1
(Example)
Enter the fax or voice number by pressing the number keys (max. of 32
digits including pauses). (Note: A space cannot be entered.)
♦ Press the SPEED DIAL key to clear a mistake.
♦ If a pause is required between any of the digits to access a special
service or an outside line, press the REDIAL key. The pause will
appear as a hyphen. Several pauses can be entered in a row.
5
Press the START/MEMORY key.
START/MEMORY
69
Sending a Fax by Automatic Dialling
6
Enter the name of the party by pressing the number keys as shown in the
chart below. Up to 20 characters can be entered.
♦ If you don't want to enter a name, skip this step.
♦ To enter two letters in succession that require the same key, press
the SPEAKER key after entering the first letter to advance the
cursor.
Example: SHARP = 77777 444 22 7777
7
SPEAKER
77
A=
J=
S=
B=
K=
T=
C=
L=
U=
D=
M=
V=
E=
N=
W=
F=
O=
X=
G=
P=
Y=
H=
Q=
Z=
I=
R=
SPACE =
Press the START/MEMORY key.
START/MEMORY
8
Return to Step 3 to store another number, or press STOP to exit. If the
number will be used for Rapid Key Dialling, you can write the name on
the appropriate Rapid Key label.
STOP
Step 3 or
Storing area codes and access codes
You can also store an area code or access code in a Rapid Key or
Speed Dial number. To use this number to dial, see Chain Dialing in
Chapter 6, Making Telephone Calls.
Note: An area code or access code stored in a Rapid Key or Speed Dial
number can only be used if the handset is lifted or the SPEAKER key
pressed before dialling.
70
Sending a Fax by Automatic Dialling
Clearing numbers
FUNCTION
Press these keys:
3
The display will show:
FAX/TEL # MODE
2
Press 2 to select CLEAR.
3
Enter the Speed Dial number that you want to clear by pressing the
number keys.
(Example)
0
1
4
Press the START/MEMORY key.
2
3. Sending
Documents
1
START/MEMORY
5
Return to Step 3 to clear another number, or press STOP to exit.
STOP
Step 3 or
Making changes
To make changes in a number previously stored, repeat the storing
procedure. Select the Speed Dial number for which you want to make
changes in Step 3, and then change the number and/or name when
they appear in the display (Steps 4 and 6, respectively).
♦ A lithium battery keeps automatic dialling numbers in memory
The machine uses a lithium battery to keep automatic dialling
numbers and other programmed data in memory when the power is
turned off. Battery power is consumed primarily when the power is
off. With the power kept continuously off, the life of the battery is
about 5 years. If the battery dies, have your dealer or retailer replace
it. Do not try to replace it yourself.
71
Sending a Fax by Automatic Dialling
Rapid Key Dialling
If the number you want to dial has been stored for Automatic Dialling
as a Speed Dial number from 01 to 08, you can dial it by pressing the
corresponding Rapid Key.
1
Load the document(s).
The display will show:
READY TO SEND
• Set the resolution and/or contrast if
desired.
2
Press the Rapid Key corresponding to
the desired Speed Dial number.
• The name of the receiving party
will appear in the display. If no
name was stored, the fax number
will appear. (If the name or number
is incorrect, press the STOP key.)
• The document will be
automatically transmitted once the
connection is made.
72
RESOLUTION
04
01
02
03
05
06
07
08/POLL
Example: To dial
Speed Dial number 01,
press Rapid Key 01.
Sending a Fax by Automatic Dialling
Speed Dialling
Speed Dialling can be used to dial any number that has been stored for
Automatic Dialling.
1
Load the document(s).
3. Sending
Documents
The display will show:
READY TO SEND
• Set the resolution and/or contrast if
desired.
2
Press the SPEED DIAL key and then
enter the two digits of the Speed Dial
number by pressing the number keys.
• To enter numbers 1 through 9, first
enter 0 and then the number.
3
Check the display. If the name or
number shown is correct, press the
START/MEMORY key. (If not,
press the STOP key and then repeat
Step 2.)
RESOLUTION
SPEED
DIAL
2
0
(Example)
START/MEMORY
73
Sending a Fax by Automatic Dialling
Direct Keypad Dialling
You can also enter a full number with the number keys and then press
the START/MEMORY key to begin dialling. You can use this
method to dial a full number when you don't need to speak to the other
party before faxing.
1
Load the document(s).
The display will show:
READY TO SEND
RESOLUTION
• Set the resolution and/or contrast if
desired.
2
Enter the number of the receiving
machine by pressing the numeric
keys.
• If a pause is required between any
of the digits to access a special
service or an outside line, press the
REDIAL key. The pause will
appear as a hyphen. Several pauses
can be entered in a row.
3
Check the display. If the number of
the receiving machine shown is
correct, press the START/MEMORY
key.
• If it is not correct, press the STOP
key to backspace and clear one digit
at a time, and then re-enter the
correct digit(s).
74
ABC
1
GHI
4
PQRS
7
2
JKL
5
TUV
8
DEF
3
MNO
6
WXYZ
9
START/MEMORY
Sending a Fax by Automatic Dialling
Using the HOLD/SEARCH key
1
3. Sending
Documents
If you don't remember the Rapid Key or Speed Dial number in which
you have stored a particular fax number, you can search for the
number by following the steps below. Once you have found the
number, you can dial it and transmit the loaded document by simply
pressing the START/MEMORY key.
Load the document(s).
The display will show:
READY TO SEND
• Set the resolution and/or contrast if
desired.
2
Press the HOLD/SEARCH key and
then the 1 key.
3
Enter the first letter of the stored
name by pressing the appropriate
number key (the key which
corresponds to the required letter) one
or more times until the letter appears
in the display. If the name begins with
a special character or number, press 1.
RESOLUTION
HOLD/
SEARCH
1
ABC
1
GHI
4
PQRS
7
2
JKL
5
TUV
8
DEF
3
MNO
6
WXYZ
9
• If you don't remember the first
letter, go to Step 4 (you will scroll
through the list from the
beginning).
• If a name wasn't stored for the
number, press 0. This will cause
numbers, not names, to appear
when you scroll.
75
Sending a Fax by Automatic Dialling
4
Press the # key or the * key to scroll
through the names (numbers if you
pressed 0). Stop when the desired
name appears in the display.
or
• If no names have been stored that
begin with the entered letter, you
will scroll from the next name, in
alphabetical order, in the list. If no
names/numbers have been stored at
all, NO DATA will appear.
5
Press the START/MEMORY key.
The document will be automatically
transmitted once the connection is
made.
START/MEMORY
Automatic redialling
If you use automatic dialling (including Direct Keypad Dialling) and
the line is busy, the machine will automatically redial the number. Up
to 2 redialling attempts will be made at intervals of 5 minutes.
♦ To stop automatic redialling, press the STOP key.
76
4. Receiving Documents
Using TEL/FAX Mode
Press the
RECEPTION MODE
key until the arrow in
the display points to
TEL/FAX.
TEL
FAX
TEL/FAX
A.M.
4. Receiving
Documents
RECEPTION
MODE
When the reception mode is set to TEL/FAX, your fax automatically
answers all calls on 2 rings. After answering, your fax monitors the
line for about 5 seconds to see if a fax tone is being sent.
♦ If your fax detects a fax tone (this means that the call is an
automatically dialled fax), it will automatically begin reception of
the incoming document.
♦ If your fax doesn't detect a fax tone (this means that the call is a
voice call or manually dialled fax), it will make a ringing sound
(called pseudo ringing) for 15 seconds to alert you to answer. If you
don't answer within this time, your fax will send a fax tone to the
other machine to allow the calling party to send a fax manually if
they desire.
Comments:
♦ Only the fax will alert you to voice calls or manually dialled faxes by
pseudo ringing. An extension phone connected to the same line will
not ring after the connection has been made.
♦ The duration of pseudo ringing can be adjusted with Option Setting
8. See Chapter 8, Option Settings.
♦ You can change the number of rings on which the machine answers
calls by changing Option Setting 2. (See Chapter 8, Option Settings.)
77
Receiving Documents
Using FAX Mode
Press the RECEPTION
MODE key until the
arrow in the display
points to FAX.
RECEPTION
MODE
TEL
FAX
TEL/FAX.
A.M.
When the reception mode is set to FAX, the machine will
automatically answer all calls on 2 rings and receive incoming faxes.
2 rings
Fax reception
♦ You can change the number of rings on which the machine answers
calls by changing Option Setting 2. (See Chapter 8, Option
Settings.)
♦ If you pick up the handset before the machine answers, you can talk
to the other party and/or receive a document as described in Using
TEL mode.
78
Receiving Documents
Using A.M. Mode
Press the RECEPTION
MODE key until the
arrow in the display
points to A.M.
RECEPTION
MODE
TEL
FAX
4. Receiving
Documents
TEL/FAX A.M.
In A.M. mode, your fax machine will automatically receive voice
messages and faxes. See Chapter 2 for more details.
79
Receiving Documents
Using TEL Mode
Press the RECEPTION
MODE key until the arrow
in the display points to
TEL.
RECEPTION
MODE
TEL
FAX
TEL/FAX
A.M.
When the reception mode is set to TEL, you must answer all calls
using the fax machine's handset or an extension phone connected to
the same line.
Answering with the fax's handset
1
Pick up the handset when the machine rings.
2
If you hear a fax tone, wait until the display shows RECEIVING and
then replace the handset.
Beep
RECEIVING
Note: If you have set Option Setting 10
(Fax signal receive) to NO, press the
START/MEMORY key to begin reception.
80
Receiving Documents
3
If the other party first talks and then wants to send a fax, press the
START/MEMORY key after speaking (press your START/
MEMORY key before the sender presses their Start key).
• Make sure that the display shows RECEIVING, then replace the
handset.
RECEIVING
START/MEMORY
4. Receiving
Documents
Answering with an extension phone
1
Answer the extension phone when it rings.
2
If you hear a fax tone when you answer the extension phone, wait until
your fax answers (the extension phone will go dead), and then hang up.
Beep
Phone goes dead
3
If the fax doesn't respond, or if the other party first talks to you and then
wants to send a fax, press 5, *, and * on the extension phone (only on
a tone dial phone). This signals the fax to begin reception. Hang up.
5
81
Receiving Documents
Comments:
♦ Your fax will not accept the signal to begin reception (5**) if a
document is loaded in its feeder.
♦ If you have set Option Setting 10 to NO and hear a fax tone when
you answer the extension phone, you must press 5, *, and * if you
are on a tone dial phone, or walk over to the fax, pick up the
handset, and press the START/MEMORY key if you are on a pulse
dial only phone.
♦ In New Zealand, not all standard telephones and answering
machines will respond to incoming ringing when connected to the
socket of the equipment.
2 in 1 Print
To save paper, you can have the size of your incoming faxes reduced
by 55%. This will allow you to receive, for example, a 2-page
document on one page (note that this may not be possible if the
document pages are longer than your printing paper). To turn on this
function, follow the steps below.
1
Press these keys:
The display will show:
2
FUNCTION
6
2 IN 1 PRINT
Press 1 to turn on the function, or 2 to turn it off.
YES
1
The display will show:
3
82
Press the STOP key.
NO
or
2
PRINT CONTRAST
STOP
Receiving Documents
Reception Ratio
The fax has been set at the factory to automatically reduce the size of
received documents to fit the size of the printing paper. This ensures
that data on the edges of the document are not cut off. If desired, you
can turn this function off and have received documents printed at full
size.
Note: Automatic reduction may not be possible if the received document
is too large, contains too many fine graphics or images, or is sent at high
resolution. In this case, the remainder of the document will be printed on
a second page.
1
Press these keys:
The display will show:
2
FUNCTION
6
RECEPTION RATIO
Press 1 to turn automatic reduction on, or 2 to turn it off.
AUTO
1
100%
or
2
• If you selected AUTO, go to Step 3. If you selected 100%, go to Step
4.
3
If you selected AUTO, select the reception ratio to be used in the event
that the memory becomes full (automatic reduction is not possible when
the memory is full). Press 1 for 93% or 2 for 100%.
93%
100%
1
or
2
83
4. Receiving
Documents
Note: If a document is too long to fit on the printing paper, the remainder
will be printed on a second page. In this case, the cut-off point may occur
in the middle of a line.
Receiving Documents
4
Press the STOP key.
STOP
Substitute Reception to Memory
In situations where printing is not possible, such as when your fax
runs out of paper, the imaging film needs replacement, or the paper
jams, incoming faxes will be received to memory.
When you have received a document in memory, FAX RX IN
MEMORY will appear in the display, alternating with OUT OF
PAPER, FILM END, or PAPER JAMMED. After you add paper,
replace the imaging film, or clear the jam, press the START/
MEMORY key and the stored documents will print out.
♦ If you received documents in memory because the fax ran out of
paper, be sure to add paper which is the same size as the paper
previously used. If not, the document print-out size may not match
the size of the printing paper.
84
5. Making Copies
Your fax can also be used to make copies. Single and multiple copies
(up to 99 per original) can be made, enabling your fax to double as a
convenience office copier.
1
Load the document(s) face down.
(Maximum of 10 pages.)
The display will show:
READY TO SEND
• Set the resolution and/or contrast if
desired. (The default setting for
copying is SUPER FINE.)
Press the COPY/HELP key.
COPY/HELP
The display will show:
5. Making
Copies
2
RESOLUTION
COPY MODE
1: MULTI COPY
2: SORT COPY
START: COPY
♦ If you are only making one copy of the original (or of each original)
and don't want to make a reduction or enlargement setting, press the
START/MEMORY key twice. Copying will begin.
♦ If you are only making one copy of the original (or of each original)
and want to make an enlargement or reduction setting, press the
START/MEMORY key and go to Step 5.
85
Making Copies
3
Press 1 (MULTI COPY) if you do not
want the copies sorted. Press 2 (SORT
COPY) if you want the copies sorted.
Example of three
copies each of
three originals
A
B C
B C
A
B C
The display will show:
4
86
or
1
2
Originals
B C
A
A A
B
B B
C
C C
ENTER # (01-99)
If you are making one copy per
original, press the START/
MEMORY key. If you are making
multiple copies per original, enter the
number of copies per original (if the
number is less than 10, enter a "0"
before the number).
The display will show:
5
A
SORT
Not sorted (MULTI COPY)
Sorted (SORT COPY)
A
MULTI
0
9
Example: Nine
copies per original
COPY RATIO
Set the amount of reduction or
enlargement by entering a number
from 1 to 5 as shown below (or press
the START/MEMORY key to
automatically select 100%). Copying
will begin.
1: AUTO (automatic size adjustment
to match the size of the printing
paper)
2: 50%
3: 100% (no reduction or
enlargement)
4: 125%
5: 135%
2
Example: 50%
Making Copies
Note: If you place a large number of originals in the feeder, the memory
may become full before all of them can be scanned (MEMORY IS FULL
will appear in the display). If this happens, press the START/MEMORY
key to copy the originals which have been scanned, and then repeat the
copy procedure for the remaining originals, including the original which
was being scanned when the memory became full.
Copy Cut-off
When making a copy of a document that is longer than the printing
paper, use the copy cut-off setting to select whether the remaining part
of the document will be cut off or printed on a second page. The intial
setting is YES (cut off the remainder). To change the setting, follow
the steps below.
1
Press these keys:
FUNCTION
6
The display will show:
2
Press 1 to set copy cut-off to YES (the
remaining part of the document will
not be printed), or 2 to set copy cutoff to NO (the remaining part will be
printed on a second page).
YES
1
5. Making
Copies
COPY CUT-OFF
NO
or
2
The display will show:
INITIALIZE FILM
3
Press the STOP key to return to the
date and time display.
STOP
87
6. Making Telephone Calls
Your fax can be used like a regular telephone to make and receive
voice calls.
♦ To make or receive a phone call, the power must be on.
1
2
Pick up the handset or press the
SPEAKER key. Listen for the dial
tone.
Dial the number using one of the
following methods:
• Normal Dialling: Enter the full
telephone number with the numeric
keys.
• Rapid Key Dialling: Press the
appropriate Rapid Key.
• Speed Dialling: Press the SPEED
DIAL key, and enter the 2-digit
Speed Dial number with the
numeric keys.
3
Speak with the other party when they
answer.
• If you pressed the SPEAKER key,
pick up the handset to talk.
88
SPEAKER
or
ABC
1
GHI
4
PQRS
7
2
JKL
5
TUV
8
DEF
3
MNO
6
WXYZ
9
Making Telephone Calls
Comments:
♦ While the handset of the fax is lifted (off hook), an extension phone
connected directly to the fax cannot be used to speak with the other
party.
♦ The fax may interrupt a voice call received on an extension phone if
the reception mode is set to A.M. and there is a period of silence
during the conversation. If you are on a tone dial phone, you can
prevent this by pressing any three keys on the phone immediately
after you answer. (Note: Do not enter the code to activate fax
reception: 5, *, *.)
Chain Dialling
After lifting the handset, you can dial any combination of Normal
Dialling, Rapid Key Dialling and Speed Dialling numbers. For
example, if you have stored an area code or an access code for a
special service in a Rapid Key, you can press the Rapid Key for that
area code or access code, then dial the remainder of the number by
pressing a Rapid Key, pressing number keys, or pressing the SPEED
DIAL key and entering a two-digit Speed Dial number.
You can use the HOLD/SEARCH key to search for a Rapid Key or
Speed Dial number. First search for the number as described in Using
the HOLD/SEARCH key in Sending a Fax by Automatic Dialling in
Chapter 3, then pick up the handset or press the SPEAKER key. The
number will be dialled automatically (do not press the START/
MEMORY key).
Redial
The last number called can be redialled by pressing the REDIAL key
(it is not necessary to pick up the handset or press the SPEAKER
key). When the other party answers, pick up the handset to talk.
89
6. Making
Phone Calls
Using the HOLD/SEARCH key
Making Telephone Calls
HOLD
You can put the other party on hold during a conversation by pressing
the HOLD/SEARCH key. When this is done, they cannot hear you.
You can put the handset back in the cradle without breaking the
connection. When you are ready to speak with them again, pick up the
handset. If you did not put the handset back in the cradle, press the
HOLD/SEARCH key again to resume conversation.
90
7. Special Functions
Caller ID
If you subscribe to a caller identification service from your telephone
company, you can set your fax to display the name and number of the
caller while the fax rings.
Important:
♦ To use this function, you must subscribe to a caller
identification service from your telephone company.
♦ Your fax may not be compatible with some caller identification
services.
1
2
Press these keys:
FUNCTION
The display will show:
OPTION SETTING
Press the * key four times.
The display will show:
3
4
CALLER-ID
Press 1 to turn on Caller ID, or 2 to
turn it off.
YES
1
7. Special
Functions
.
NO
or
2
91
Caller ID
4
Press 1 if you are in Australia or 2 if
you are in New Zealand.
The display will show:
5
AUSTRALIA NEW ZEALAND
1
or
2
COVER SHEET
Press the STOP key to return to the
date and time display.
STOP
How Caller ID operates
When you receive a call, the name and/or phone number of the caller
will alternately appear in the display, beginning just before the second
ring. The information will continue to be displayed until you pick up
the handset, or until the fax answers automatically if it is in FAX mode.
Note: Some caller ID services may not provide the name of the caller. In
this case, only the phone number will appear.
Display example
DOE JOHN
444-555-6666
Caller’s name
Caller’s number
Display messages
One of the following messages will appear while the fax rings if caller
information is not available.
92
NO SERVICE
No caller information was received from your
telephone company. Make sure that the
telephone company has activated your
service.
CALLER-ID
ERROR
Noise on the telephone line prevented
reception of caller information.
Caller ID
The call was made from an area which does
UNAVAILABLE
(OUT OF AREA in New not have a caller identification service, or the
caller's service is not compatible with that of
Zealand)
your local phone company.
Caller information was not provided by the
PRIVATE
(ANONYMOUS in New telephone company at the caller's request.
Zealand)
Viewing the Caller ID list
If you subscribe to a Caller ID service and have turned on the Caller
ID function, your fax machine will keep information on the most
recent 20 calls and faxes you have received. You can view this
information, which consists of the name and number of each caller, in
the Caller ID List.
Note: For all units installed in New Zealand, the direct use of the
displayed number for call back does not operate properly and must not be
used. It is necessary to manually enter the verified correct number for the
party called. This will often require the addition or deletion of leading
digits from the number shown on the display when dialling manually.
♦ After you have received 20 calls, each new call will delete the oldest
call.
Follow the steps below to view the Caller ID List in the display. If
desired, you can immediately dial a number when it appears.
To print out the list, see Chapter 9, Printing Reports and Lists.
Press these keys:
The display will show:
2
HOLD/
SEARCH
2
7. Special
Functions
1
REVIEWING CALLS
Press the * key to scroll through the
list from the most recent call, or the #
key to scroll through the list from the
oldest call.
or
93
Caller ID
3
If you want to dial one of the numbers
in the list, scroll through the list until
the number appears in the display.
• If you want to send a fax, load the
document and then press the
START/MEMORY key.
START/MEMORY
• If you want to make a voice call,
pick up the handset or press the
SPEAKER key. Dialing will begin
automatically. (If you pressed the
SPEAKER key, pick up the
handset when the other party
answers.)
4
Press the STOP key when you have
finished viewing the list.
STOP
To delete calls from the caller list
If you want to delete a single call from the caller list, press the "0" key
while the call appears in the display. If you want to delete all calls
from the list, hold the "0" key down for at least 3 seconds while you
are viewing any number in the list.
Priority Call
If desired, you can set your fax to make a special ringing sound when
you receive a call from a designated phone number. This lets you
know immediately who is calling without having to look at the
display. To use this function, enter the desired phone number by
following the steps below (only one phone number can be entered).
94
Caller ID
1
Press the keys shown at right.
PRIORITY CALL # will appear in
the display.
FUNCTION
2
Press 1 to enter a number, or 2 to clear
a number. (If you pressed 2, go to
Step 4.)
3
Enter the phone number, including the
area code, by pressing the number
2
keys (max. of 20 digits).
3
1
3
2
or
2
4
5
6
7
(Example)
4
Press the START/MEMORY key
and then the STOP key.
STOP
START/MEMORY
Blocking voice calls
In this case when a voice call or a fax transmission comes in from a
number you have specified as a "Junk Number", your fax will terminate
the call as soon as it receives the calling phone number from the caller ID
service. The caller will hear a 3 second high pitch tone to signal the calls
termination. In Australia the call will not break off until the caller has
hung up.
To use this function, set Option Setting 11 to YES as described in Chapter
8, Option Settings, and then enter the number in the Anti Junk Number
List as explained in Blocking Reception of Unwanted Faxes in this
chapter.
Note: This function cannot be used if you are using Distinctive Ring.
95
7. Special
Functions
With Caller ID turned on, you can use the Anti Junk Fax function
described in Blocking Reception of Unwanted Faxes in this chapter to
prevent voice calls as well as fax receptions (the Anti Junk Fax function
can normally only prevent faxes).
Distinctive Ring
Distinctive Ring
If you subscribe to a distinctive ring service from your telephone
company, you will need to turn on the distinctive ring function. When
this is done, your fax machine will signal voice calls by the normal
ring pattern, and fax transmissions by a special ring pattern. In the
case of a fax transmission, your fax machine will automatically
answer the call and receive the fax.
The distinctive ring function is used with the reception mode set to
FAX. When your fax number is dialled, your fax machine will signal
the call with a special ringing sound, then answer automatically and
begin reception after the number of rings set with Option Setting 2
(the factory setting is 2 rings). When your voice number is dialled, the
fax machine will signal the call with the normal ringing sound to let
you know that you must answer personally.
The factory setting is "NO". If set to "YES", both Australian (Fax
Duet) and New Zealand (Fax Ability) Distinctive Ring are supported.
Important:
♦ The distinctive ring function can only be used if you subscribe to a
distinctive ring service from your telephone company. Do not turn
on distinctive ring if you are on a normal line, as the fax machine
will not operate properly.
♦ If you turn on distinctive ring, the fax will not operate in TEL/FAX
reception mode.
1
Press these keys:
FUNCTION
The display will show: OPTION SETTING
2
Press these keys:
The display will show: DISTINCTIVE RING
96
4
Distinctive Ring
3
Press 1 (YES) to turn on distinctive ring, or 2 (NO) to turn it off.
YES
1
NO
or
2
The display will show: FAX SIGNAL RX
Press the STOP key.
5
Set the reception mode to FAX.
RECEPTION
MODE
STOP
TEL
FAX
TEL/FAX. A.M.
7. Special
Functions
4
97
Broadcasting
Broadcasting
This function allows you to send the same document to as many as 20
different locations with just one operation. First store the document in
memory, then enter the numbers of the receiving machines. The
document will be transmitted to each location.
♦ You can only use Rapid Keys or Speed Dial numbers to dial the
numbers of the receiving machines.
1
Load the document(s).
The display will show:
READY TO SEND
2
3
Press the START/MEMORY key
and then 2.
2
START/MEMORY
Dial the receiving machines by using
one or both of the following methods.
(a maximum of 20 stations can be
selected).
• Enter one or more Speed Dial
numbers by pressing the numeric
keys.
2
04
2
01
02
03
05
06
07
• Press one or more Rapid Keys.
4
Press the START/MEMORY key.
START/MEMORY
• Set the resolution and/or contrast if
desired.
98
RESOLUTION
08/POLL
Broadcasting
Press the START/MEMORY key.
Transmission will begin.
START/MEMORY
• A Transaction Report is
automatically printed out after
Broadcasting is completed. Check
the "Note" column of the report to
see if any of the locations are
marked "Busy" or have a
communication error code. If so,
send the document to those
locations again.
7. Special
Functions
5
99
Cover Sheet
Cover Sheet
You can have the fax generate a cover sheet and send it as the last page
of each of your fax transmissions.
You can select
a message.
For the recipient's
name to appear, you
must dial using a
Speed Dial or Rapid
Key number with the
name programmed.
Your name and
number must be
programmed as
explained in
Chapter 1.
Follow the steps below to turn on the cover sheet function. Once the
cover sheet function is turned on, cover sheets will be included with
all tranmissions until you turn it off.
1
Press these keys:
The display will show:
OPTION SETTING
2
Press these keys:
The display will show:
COVER SHEET
100
FUNCTION
4
Cover Sheet
3
Press 1 (YES) to turn on the cover
sheet function, or 2 (NO) to turn it off.
YES
1
NO
or
2
The display will show:
AUTO PRINT OUT
4
Press the STOP key to return to the
date and time display.
STOP
Selecting a header message (optional)
When the cover sheet function is turned on, you can also select a
message which will appear as a header at the top of the cover sheet.
Note that the message selection is only effective for one transmission.
1
Load the document(s).
• The document must be loaded
before a message can be selected.
2
7. Special
Functions
• The cover sheet function must be
turned on.
Press these keys:
FUNCTION
The display will show:
5
COVER SHEET HEAD
101
Cover Sheet
3
4
Select a message by entering a
number from 1 to 4:
1: URGENT
2: IMPORTANT
3: CONFIDENTIAL
4: PLS. DISTRIBUTE
1
(Example)
Dial the receiving machine and
transmit the document.
Note: To cancel a cover sheet header setting, press the STOP key or
remove the document from the feeder.
102
Batch Page Numbering
Batch Page Numbering
You can change the page numbering of the transmitted document from
simple numbering ("P.01", "P.02", etc.) to batch numbering, which
means that a slash and the total number of pages being sent are added
after each page number (for example, "P. 01/05", "P.02/05", etc.). This
allows the receiver to check for missing pages.
1
Load the document(s).
• The document must be loaded
before batch page numbering can
be set.
2
Press these keys:
FUNCTION
The display will show:
PAGE COUNTER SET
Enter the total number of pages ("01"
to "99") by pressing the number keys.
• If you are sending a cover sheet, do
not include it in the total number of
pages (the number will be adjusted
automatically).
4
0
8
Example:
Eight pages
7. Special
Functions
3
Dial the receiving machine and
transmit the document.
103
Batch Page Numbering
Comments:
♦ If you need to cancel a batch number entry, remove the document
from the feeder or press the STOP key.
♦ If the number of pages actually transmitted does not coincide with
the batch number entered, the alarm will sound and PAGE COUNT
ERROR will appear in the display. PAGE E. will also appear in the
NOTE column of the Transaction Report if it has been set to print
out.
104
Blocking Reception of Unwanted Faxes
Blocking Reception of Unwanted Faxes
The Anti Junk Fax function allows you to block reception of faxes
from parties which you specify. This saves paper by not printing out
unwanted "junk" faxes.
To use this function, first turn it on by setting Option Setting 11 to
YES as explained in Chapter 8, and then enter the fax numbers from
which you do not want to receive faxes as shown below.
Comments:
♦ Up to 5 numbers can be entered in the Anti Junk Number List.
♦ The Anti Junk function will not operate for a number which has also
been stored as a Priority Call number.
♦ To clear a number from the Anti Junk Number List, you need to
know the 1-digit number which identifies it. If you have forgotten
this number, print out the Anti Junk Number List as explained in
Chapter 9.
Press the keys shown at right.
STORE JUNK # will appear in the
display.
2
Press 1 to store a number in the Anti
Junk Number List, or 2 to clear a
number from the list.
3
Storing: Enter a 1-digit number from
1 to 5. This number identifies the fax/
voice number you will store in the
next step.
Clearing: Enter the number which
identifies the fax/voice number you
want to clear, and go to Step 5.
FUNCTION
3
SET
1
CLEAR
or
2
7. Special
Functions
1
1
(Example)
105
Blocking Reception of Unwanted Faxes
4
Enter the full number you want to
block (max. of 20 digits).
2
3
2
4
5
6
(Example)
5
Press the START/MEMORY key.
START/MEMORY
6
106
Return to Step 3 to enter (or clear)
another number, or press STOP to
exit.
STOP
Step 3 or
7
Sending Documents From Memory
Sending Documents From Memory
With this function, the original document is scanned immediately,
stored in memory, and then transmitted once the connection to the
receiving machine is made. This is convenient when transmitting to
places where the line is often busy, as it saves you from waiting to
pick up the original document and frees the feeder for other
operations. After transmission, the document will be cleared from
memory.
♦ Only one memory transmission can be set at a time.
♦ The amount of memory currently occupied appears as a percentage
in the display while the document is being scanned.
1
Load the document(s).
The display will show:
READY TO SEND
2
RESOLUTION
Press the START/MEMORY key
and then 1.
1
7. Special
Functions
• Set the resolution and/or contrast if
desired.
START/MEMORY
The display will show:
ENTER STATION #
107
Sending Documents From Memory
3
Enter the number of the receiving
machine using one of the following
methods:
• Press a Rapid Key.
01
02
03
(Example)
• Press the SPEED DIAL key and
enter a Speed Dial number.
• Enter a full telephone number by
pressing the number keys.
4
Press the START/MEMORY key if
you entered a Speed Dial number or a
full number.
START/MEMORY
• The document will be scanned and
stored in memory. Your fax will
then dial the receiving machine and
transmit the document (redialling
will be done automatically if
necessary).
If the memory becomes full...
If the memory becomes full while the document is being scanned,
MEMORY IS FULL will appear in the display.
♦ Press the START/MEMORY key if you want to transmit the pages
which have been stored up to that point in memory. The remaining
pages will be ejected from the feeder. After transmission, the
memory will be cleared and you can transmit the remaining pages.
You will also need to transmit the page which was being scanned
when the memory filled up.
♦ Press the STOP key if you want to cancel the entire transmission.
108
Polling (Requesting a Fax Transmission)
Polling (Requesting a Fax Transmission)
Polling allows you to call another fax machine and have it send a
document (previously loaded in its feeder) to your machine without
operator assistance. In other words, the receiving fax machine, not the
transmitting fax machine, initiates the transmission. You can use your
machine to both poll and be polled by others.
To use the polling function, you must first set Rapid Key 08/POLL for
use as a polling key. This is done by changing Option Setting 12, as
described in Chapter 8, Option Settings. (Note that when Rapid Key
08/POLL is set as a polling key, it cannot be used for Rapid Key
Dialling.)
Requesting transmission
1
Dial the fax machine you want to poll
using one of the following methods:
• Pick up the handset (or press the
SPEAKER key) and press a Rapid
key. Wait for the fax answerback
tone.
• Pick up the handset (or press the
SPEAKER key) and dial the full
number. Wait for the fax
answerback tone.
• Press the SPEED DIAL key and
enter a 2-digit Speed Dial number.
ABC
1
GHI
4
PQRS
7
2
JKL
5
TUV
8
DEF
3
MNO
6
WXYZ
9
(Example)
2
Press Rapid Key 08/POLL.
7. Special
Functions
• Enter the full number using the
numeric keys.
08/POLL
• If you used the handset, replace it
when POLLING appears in the
display. Reception will begin.
109
Polling (Requesting a Fax Transmission)
Being polled (polling standby)
To let another fax machine poll your machine, simply set the reception
mode to FAX, and load the document(s) to be sent.
Transmission will take place when the other fax machine calls your
machine and activates polling. Automatic reception is possible whilst
your fax is on polling standby.
Polling security
Polling Security allows you to prevent unauthorized polling of your
machine. When this function is turned on, polling will only take place
when the fax number of the polling fax machine has been entered in
your machine's list of permitted fax numbers (called "passcode
numbers"). The number of the polling fax must also be correctly
programmed into itself for identification.
To use Polling Security, follow the steps below to turn the function on,
and then enter permitted numbers as shown on the following page.
1
Press the keys shown at right.
ENTRY MODE will appear in the
display.
2
Press the # key three times.
SECURITY SELECT will appear in
the display.
3
Press 1 to turn polling security on, or
2 to turn it off.
4
Press the START/MEMORY key
and then the STOP key.
FUNCTION
3
1
or
STOP
START/MEMORY
110
2
Polling (Requesting a Fax Transmission)
Storing and clearing fax numbers for polling permission
You can store up to 10 fax numbers in your machine's list of permitted
numbers.
1
Press the keys shown at right.
ENTRY MODE will appear in the
display.
2
Press the # key four times.
PASSCODE # MODE will appear in
the display.
3
Press 1 to store a number, or 2 to clear
a number.
4
Storing: Enter a 2-digit number from
01 to 10. This number identifies the
fax number you will store in the next
step.
Clearing: Enter the number which
identifies the fax number you want to
clear, and go to Step 6.
5
Enter the fax number (max. of 20
digits).
FUNCTION
3
or
1
0
2
1
(Example)
2
3
2
4
5
6
7
6
7. Special
Functions
(Example)
Press the START/MEMORY key.
START/MEMORY
7
Return to Step 4 to enter (or clear)
another number, or press STOP to
exit.
STOP
Step 4 or
111
Timer Operations
Timer Operations
The Timer function allows you to set a transmission and/or polling
operation to be performed automatically at a time you specify. One
transmission operation and one polling operation can be set at the
same time, and the times they will be performed can be specified up to
24 hours in advance.
As an example, you can use this function to take advantage of offpeak telephone rates without having to be there when the operation is
performed.
Note: Only a Speed Dial number can be used to dial the receiving
machine.
Setting a timer operation
1
Press the keys shown at right.
TIMER MODE will appear in the
display.
2
Press # to set a transmission operation
(SEND MODE), or * to set a polling
operation (POLLING MODE).
3
Press 1 to select SET.
4
Enter the time at which you want the
operation to take place in 24-hour
format (2 digits for the hour and 2
digits for the minute).
5
FUNCTION
1
or
1
0
9
2
Example: 9:25
Press the START/MEMORY key.
START/MEMORY
112
5
Timer Operations
6
Enter the Speed Dial number of the
receiving fax machine.
0
5
• If this is a polling operation, go to
Step 9.
7
(Example)
Press the START/MEMORY key.
START/MEMORY
8
Adjust the resolution and/or contrast
if desired (skip to the next step if you
don't want to change settings).
9
Press the START/MEMORY key
and then the STOP key. If this is a
transmission operation, load the
document in the feeder sometime
before the specified time of
transmission.
RESOLUTION
STOP
START/MEMORY
To cancel an operation
If you need to cancel an operation after it has been set, follow the
steps below.
Press the keys shown at right.
TIMER MODE will appear in the
display.
2
Press # to cancel a transmission
operation, or * to cancel a polling
operation.
3
Press 2 to select CLEAR.
4
Press the START/MEMORY key
and then the STOP key.
FUNCTION
1
7. Special
Functions
1
or
2
STOP
START/MEMORY
113
8. Option Settings
The option settings let you customise your fax to better suit your
needs. An initial setting has been made for each option at the factory.
You can change a setting by following the steps described for each
option below.
FUNCTION
First press FUNCTION
and 4, then press # or *
to scroll through the
options.
4
or
Setting 1: FINE RESOLUTION PRIORITY
This option sets the default resolution (the resolution used if a setting is not
made with the RESOLUTION key) for transmitting documents. Press 1
(YES) to set the default resolution to FINE, or 2 (NO) to set it to
STANDARD.
♦ Initial setting: 2
FUNCTION
4
YES
1
114
Display
will show:
FINE PRIORITY
NO
or
2
NUMBER OF RINGS
STOP
Setting 2: NUMBER OF RINGS TO ANSWER
This sets the number of rings the fax machine waits before answering an
incoming call in FAX and TEL/FAX reception modes. Enter any number
from 2 to 4.
♦ Initial setting: 2
FUNCTION
4
Enter a number
from 2 to 4
Press
until
display
shows:
NUMBER OF RINGS
4 RINGS TEL ANS.
STOP
Setting 3: 4 RINGS TEL ANSWER
Press 1 (YES) to have the fax machine answer a call after 4 rings when it
is in TEL reception mode. Press 2 (NO) to turn the function off.
♦ Initial setting: 2
FUNCTION
4
YES
1
NO
or
2
Press
until
display
shows:
4 RINGS TEL ANS.
TEL/FAX REMOTE #
STOP
115
8. Option
Settings
Option Settings
Option Settings
Setting 4: TEL/FAX REMOTE NUMBER (TRANSFER CODE)
If you hear a fax tone when you answer a call on a tone dial extension
phone connected to the same line as the fax, you can make the fax begin
reception by pressing 5, *, and * on the phone. Use this setting if you
want to use a number other than 5 to begin fax reception. You can enter
any number from 0 to 9.
♦ Initial setting: 5
FUNCTION
4
Press
Enter a number
from 0 to 9
until
display
shows:
TEL/FAX REMOTE #
REMOTE RECEPTION
STOP
Setting 5: REMOTE RECEPTION SELECT
If you don't intend to use the above TEL/FAX REMOTE NUMBER, you
can turn detection of the number off. This will ensure that the fax never
mistakenly attempts to begin reception if it detects a signal similar to the
TEL/FAX REMOTE NUMBER while you are talking on an extension
phone. Press 1 to turn detection on, or 2 to turn detection off.
♦ Initial setting: 1
FUNCTION
4
YES
1
116
NO
or
2
Press
until
display
shows:
REMOTE RECEPTION
TRANSACTION LIST
STOP
8. Option
Settings
Option Settings
Setting 6: TRANSACTION REPORT PRINT SELECT
TThis sets the condition for printing out a Transaction Report. Enter a
number from 1 to 5 as follows:
1 (ALWAYS PRINT):
A report will be printed after each transmission,
reception, or error.
2 (ERR/TIMER/MEM): A report will be printed after an error, timer
operation, or memory operation.
3 (SEND ONLY):
A report will be printed only after a transmission.
4 (NEVER PRINT):
A report will never be printed.
5 (ERROR ONLY):
A report will be printed only after an error occurs.
♦ Initial setting: 5
FUNCTION
4
Enter a number
from 1 to 5
Press
until
display
shows:
TRANSACTION LIST
STOP
DIAL MODE
Setting 7: DIAL MODE
This sets the mode of dialling. Press 1 if you are on a tone dial line, or 2 if
you are on a pulse dial line.
♦ Initial setting: 1
FUNCTION
4
TONE PULSE
1
or
2
Press
until
display
shows:
DIAL MODE
PSEUDO RING DUR.
STOP
Note: For all units installed in New Zealand, select "1" for tone dialling.
The pulse setting "2" will not operate correctly and must not be used.
117
Option Settings
Setting 8: PSEUDO RINGING DURATION
This sets the duration of pseudo ringing in TEL/FAX reception mode.
Press 1 for 15 seconds, 2 for 30 seconds, 3 for 60 seconds, or 4 for 120
seconds.
♦ Initial setting: 1
FUNCTION
4
Enter a number
from 1 to 4
Press
until
display
shows:
PSEUDO RING DUR.
DISTINCTIVE RING
STOP
Note for New Zealand: Telecom regulations do not permit the 60-second
and 120-second settings to be used.
Setting 9: DISTINCTIVE RING
If you subscribe to a distinctive ring service from your telephone
company, press 1 to have your fax signal voice calls and fax
transmissions by different ring patterns. Press 2 to turn the function off.
(This setting is described in more detail in Distinctive Ring in Chapter 7.)
♦ Initial setting: 2
FUNCTION
4
YES
1
Press
NO
or
2
until
display
shows:
FAX SIGNAL RX
DISTINCTIVE RING
STOP
Setting 10: FAX SIGNAL RECEIVE
Your fax will automatically begin reception if you hear a high-pitched fax
tone after answering a call. If you use a computer fax modem on the same
line, you must turn this function off in order to prevent your fax from
mistakenly attempting to receive documents sent from the computer fax
modem. Press 1 to turn the function on, or 2 to turn it off.
♦ Initial setting: 1
FUNCTION
4
YES
1
118
NO
or
2
Press
until
display
shows:
JUNK # CHECK
FAX SIGNAL RX
STOP
8. Option
Settings
Option Settings
Setting 11: JUNK FAX NUMBER CHECK
Press 1 to prevent reception from fax numbers entered in the Anti Junk
Fax List. Press 2 to allow reception from all numbers.
♦ Initial setting: 2
FUNCTION
Press
4
YES
1
NO
or
until
display
shows:
JUNK # CHECK
STOP
POLLING
2
Setting 12: POLLING
Press 1 if you want to use Rapid Key 08/POLL as a polling key. Press 2 if
you want to use it as a regular Rapid Key.
♦ Initial setting: 2
FUNCTION
Press
4
YES
1
NO
or
until
display
shows:
POLLING
STOP
CALLER-ID
2
Setting 13: CALLER ID
If you subscribe to a Caller ID service and want to use the Caller ID
function, press 1. To turn Caller ID off, press 2. (Caller ID is explained in
more detail in Caller ID in Chapter 7.)
♦ Initial setting: 2
FUNCTION
Press
4
YES
1
CALLER-ID
NO
or
2
AUSTRALIA
1
until
display
shows:
COUNTRY SELECT
NEW ZEALAND
or
2
COVER SHEET
STOP
119
Option Settings
Setting 14: AUTO COVER SHEET
Press 1 (YES) to have the fax automatically generate a cover sheet and
send it as the last page of each transmission. Press 2 (NO) to turn the
function off.
♦ Initial setting: 2
FUNCTION
4
YES
1
NO
or
2
Press
until
display
shows:
COVER SHEET
AUTO PRINT OUT
STOP
Setting 15: ACTIVITY REPORT AUTO PRINT OUT
Press 1 to have your fax automatically print out an Activity Report once
every 30 operations. (The list can still be printed out on demand when
desired.) Press 2 to turn automatic print-out off.
♦ Initial setting: 2
FUNCTION
4
YES
1
NO
or
2
until
display
shows:
AUTO PRINT OUT
ECM MODE
STOP
Setting 16: ERROR CORRECTION MODE (ECM)
Press "1" (YES) to have any distortions in a transmission due to noise on
the telephone line be corrected before print-out at the receiving end. This
is only effective when the other machine has ECM as well. Press "2"
(NO) to turn the function off.
♦ Initial setting: 1
FUNCTION
4
YES
1
120
display will ECM MODE
shows:
NO
or
2
FINE PRIORITY
STOP
You can print out lists showing settings and information entered in the
fax. You can also have the fax automatically print out a report on
transactions after they are made. The lists and the report are described
below.
Printing a list
1
Press these keys:
FUNCTION
2
The display will show: LISTING MODE
2
Press the # key or the * key until the desired list appears in the display.
or
3
Press the START/MEMORY key.
START/MEMORY
Activity Report
This report shows information on your most recently performed send
and receive operations (a combined maximum of 30 operations can
appear). The report is divided into two parts: the TRANSMISSIONS
ACTIVITY REPORT, which shows information on transmissions, and
the RECEPTIONS ACTIVITY REPORT, which shows information
on receptions.
121
9. Printing
Lists
9. Printing Reports and Lists
Printing Lists
♦ If Option Setting 15 (Auto Print Out) is set to YES, a report will be
automatically printed out whenever information on 30 operations
has accumulated. (A report can still be printed on demand at any
time.)
♦ All information is erased after a report is printed out. If automatic
print-out is disabled and print-out has not been performed manually
for 30 operations, the information on the oldest operation will be
overwritten each time a new operation is performed.
Explanation of headings
SENDER/ The fax number of the other machine involved in the transaction.
RECEIVER In the case of a transmission, the number dialled appears. In the
case of a reception, the programmed ID of the sending machine
appears. If this machine does not have an ID function, the
communication mode will appear (for example, "G3").
PAGES
Number of pages transmitted or received.
NOTE
OK - Transmission/reception was normal.
P.FAIL - A power failure occurred. If you have power and the
problem persists, try a different outlet. If necessary, have an
electrician check your power lines.
JAM - A problem with the paper or original document occurred.
Make sure the paper or document is loaded properly. Make sure
the operation panel is shut securely.
NO PAPER - You ran out of paper during reception.
122
Printing Lists
CANCEL - Transmission was cancelled because the STOP key
was pressed, no document was in the feeder, or the other
machine requested transmission using a function which your fax
does not have. If you were attempting to fax, make sure a
document is in the feeder. If you were receiving, contact the
faxing party to see how they are trying to send to you.
Timer List
This list shows the timer operations which are currently set.
Telephone Number List
This list shows the fax and voice numbers which have been stored for
automatic dialling.
123
9. Printing
Lists
COM.E-0 to COM.E-7 - A telephone line error prevented the
transaction. See Line Error in Chapter 11.
Printing Lists
Passcode List
This list shows settings made for polling security, your name and fax/
telephone number as entered in the machine, and a sample of the
header printed at the top of every page you transmit (HEADER
PRINT).
Option Setting List
This list shows the current status of the option settings.
124
Printing Lists
Anti Junk Number List
9. Printing
Lists
This list shows the numbers that are blocked by the Anti Junk
function.
A.M. Program List
This list shows the settings and codes programmed for the answering
machine.
125
Printing Lists
Message List
This list shows information about the messages currently recorded in
the answering machine, including the date and time of recording, the
length, and the type (ICM , memo or 2-way).
Caller ID List
This list shows information about your most recent calls (maximum of
20 calls). (This list is only available if you are using the Caller ID
function.)
126
Printing Lists
This list shows the current status of the printing settings accessed by
pressing the FUNCTION key and the 6 key.
Transaction Report
This report is printed out automatically after an operation is
completed to allow you to check the result. Your fax is set at the
factory to print out the report only when an error occurs. If desired,
you can change the setting to have it printed out under a variety of
other conditions. This is done by changing Option Setting 6
(Transaction Report Print Select) as described in Chapter 8.
♦ The same headings appear in the Transaction Report as in the
Activity Report. See Activity Report in this chapter for an
explanation of the headings.
♦ The Transaction report cannot be printed out manually.
127
9. Printing
Lists
Print Setup List
10. Maintenance
Fax print head
Clean the printing head frequently to assure optimum printing
performance.
1
First unplug the telephone line, then unplug the power cord.
For Australia
For New Zealand
2
Pull the paper release plate forward and remove the paper.
3
Open the operation panel (grasp the finger hold and pull up), and then
pull the release on the right side of the machine forward to open the
print compartment cover.
128
Maintenance
Take the imaging film cartridge out of the print compartment and place
it on a sheet of paper.
5
Wipe the print head and roller with isopropyl alcohol.
10. Maintenance
4
Roller
Print head
Caution!
♦ Do not use benzene or thinner. Avoid touching the print head with
hard objects.
♦ The print head may be hot if your fax machine has just received a
large number of documents. If this is the case, allow the print head
to cool prior to cleaning.
129
Maintenance
6
Place the imaging film cartridge back in the print compartment.
7
Close the print compartment cover (press down on both sides to make
sure it clicks into place), and then close the operation panel.
8
Pull the paper release plate toward you, reinsert the paper in the paper
tray and push the paper release plate back down.
If SET PAPER & PRESS START KEY appears in the display, make
sure the paper is inserted correctly and then press the START/
MEMORY key.
130
Maintenance
Scanning glass and rollers
♦ Make sure that all dirt and stains (such as correcting fluid) are
removed, as dirt and stains will cause vertical lines on transmitted
images and copies. If necessary, use a cloth moistened with
isopropyl alcohol.
♦ Adhesive cellophane tape is useful for removal of debris from the
rollers.
Document
rollers
Scanning glass
Caution: When wiping, take care not to damage any of the protruding
parts on the underside of the operation panel.
Cleaning the housing
Wipe the external parts and surface of the machine with a dry cloth.
Caution!
♦ Do not use benzene or thinner. These solvents may damage or
discolor the machine.
131
10. Maintenance
Clean the scanning glass and rollers frequently to ensure the quality of
transmitted images and copies. Open the operation panel (grasp the
finger hold and pull up), and wipe the scanning glass and rollers with
a soft cloth.
11. Troubleshooting
Problems and Solutions
Line error
Problem
LINE ERROR appears in
the display and/or a
transaction report is
printed out with COM. Eand a number from 0 to 1,
2, 3, 4, 5, 6, or 7 in the
NOTE column.
Check and remedy
• Try the transaction again. If the error persists,
check the following:
• Check the connection. The cord from the TEL.
LINE socket to the wall socket should be no longer
than two meters.
• Make sure there are no modem devices sharing the
same telephone line.
• Check with the other party to make sure their fax
machine is functioning properly.
• Have your telephone line checked for line noise.
• Try connecting your fax to a different telephone
line.
• If the problem still occurs, your fax machine may
need service.
Dialling and transmission problems
Problem
Check and remedy
No dial tone when you
pick up the handset or
press the SPEAKER key.
• Make sure the handset cord is connected to the
correct socket. See Handset in Connections in
Chapter 1.
Dialling is not possible.
• Make sure the power cord is properly plugged into
a power outlet.
• Make sure that the telephone line is properly
connected to both the TEL. LINE socket and the
wall socket.
• Make sure that the fax is set to the correct dialling
mode for your telephone line. See Option Setting 7
in Chapter 8.
132
Problems and Solutions
The power is on, but no
transmission takes place.
• Make sure that the receiving machine has fax
paper.
• Make sure that the telephone line cord is plugged
into the TEL. LINE socket, and not the TEL. SET
socket.
• If the receiving machine is in manual mode with no
attendant, reception will not be possible.
• If the receiving machine is not a Sharp model,
make sure it is G3 compatible.
• Check the display for error messages.
Nothing is printed at the
receiving end.
• Make sure that the document for transmission is
placed face down in the feeder.
A distorted image is
received at the other end.
• Noise on the telephone line may cause distortion.
Try sending the document again.
11. Troubleshooting
• Pick up the handset and check for a dial tone. Call
the receiving machine by normal (manual) dialling,
and confirm its response.
• Make a copy of the document on your fax. If the
copy is also distorted, your fax may have a
problem. If the problem persists, call for service.
Reception and copying problems
Problem
Check and remedy
The power is on, but no
reception takes place.
• Make sure the wall socket is connected to the TEL.
LINE socket, and not the TEL. SET socket.
The printing paper comes
out blank when you try to
receive a document.
• Make sure that the document is loaded properly in
the feeder of the transmitting machine. Make a
copy to confirm the printing ability of your machine.
133
Problems and Solutions
General print quality is
poor.
• It is important to select a paper that is appropriate
for the thermal transfer printer in your fax. We
recommend using laser quality paper that has a
very smooth finish. Copier paper will work, but it
sometimes tends to yield a lighter print quality.
The received document is
faint.
• Ask the other party to send higher contrast
documents. If the contrast is still too low, your fax
may have a problem. Make a copy to check it.
Received images are
distorted.
• Noise on the telephone line may cause distortion.
Have the other party try sending the document
again.
• The print head may be dirty. See Fax print head in
Chapter 10.
• Make a copy of another document on your fax. If
the copy is also distorted, your fax may have a
problem. If the problem persists, call for service.
The quality of copies is
poor and/or black spots
appear.
• Any dirt or material on the scanning glass will
cause spots to appear on copies and transmitted
faxes. Clean the fax print head and the scanning
glass as explained in Chapter 10.
Reception/copying is
interrupted.
• If reception or copying takes place continuously for
a long time, the print head may overheat. Turn off
the power and let it cool down.
A received document or
copy prints out in strips.
• Make sure the operation panel and the printer
compartment cover under the operation panel are
completely closed (press down on both sides of
each). (To close the printer compartment cover,
grasp the top of the operation panel and pull to
open it, and then press down on both sides of the
printer compartment cover.)
134
Problems and Solutions
General problems
Problem
Check and remedy
Information cannot be
programmed in the fax.
• Make sure the fax is plugged in and the imaging
film and paper have been loaded. (Programming is
not possible if the imaging film and printing paper
have not been loaded.) See Loading the Imaging
Film and Loading Printing Paper in Chapter 1.
Nothing appears in the
display.
• Make sure the power cord is properly plugged into
a power outlet.
• Connect another electrical appliance to the outlet to
confirm that it has power.
• If a beep sound is not made when you press the
keys, unplug the power cord and then plug it back
in several seconds later.
Automatic document
feeding does not work for
transmission or copying.
• Check the size and weight of the document (see
Transmittable documents in Chapter 3).
Voice calls taken on an
extension phone are
interrupted by the fax.
• The fax may interrupt during a voice call if the
reception mode is set to A.M.. To prevent
interruption on a tone dial extension phone, press
any three keys on the extension phone after
answering. (Note: Do not enter the code to activate
fax reception.)
No reception occurs when
polling is attempted.
• Make sure you have not run out of paper.
11. Troubleshooting
The machine does not
respond when you press
any of its keys.
• Make sure the transmitting machine is in automatic
reception mode.
• If the transmitting machine has polling security,
make sure that your fax number has been entered
both in your machine and in the transmitting
machine.
Bell Tinkle
(New Zealand)
• The operation of this equipment on the same line
as the telephone or other equipment with audible
warning devices or automatic ring detectors will
give rise to bell tinkle or noise and may cause false
tripping of the ring detector. Should such a problem
occur, contact your authorised Sharp Service
Centre for information.
135
Display Messages
Messages and Signals
Display messages
Note: If you have turned on the Caller ID function, see Caller ID in
Chapter 7 for display messages related to Caller ID.
A.M. TRANSFER
The answering machine's transfer function has been
turned on as explained in Transfer Function in
Chapter 2.
CHECK PAPER SIZE
An incorrect size of paper has been loaded in the
paper tray. Remove the paper and load A4-size
paper.
COVER OPEN
The print compartment cover (under the operation
panel) is open. Open the operation panel (grasp the
top and pull toward you), and then press down firmly
on both sides of the print compartment cover to close
it.
DOCUMENT JAMMED
The original document is jammed. See the following
section, Clearing Paper Jams.
FAX RX IN MEMORY
A fax has been received in memory because the
imaging film needs replacement, you have run out of
printing paper, or the paper is jammed. The fax will
print out automatically when the problem is fixed.
FILM END
The imaging film may need replacement. Check the
film and replace if necessary.
FUNCTION MODE
The FUNCTION key has been pressed.
HOLD
The HOLD/SEARCH key has been pressed to put
the other party on hold during a phone conversation.
Press the HOLD/SEARCH again to take the other
party off hold
LINE ERROR
Transmission or reception was not successful. Press
STOP to clear the message, and then try again. If the
error persists, see Line Error in Problems and
Solutions in this chapter.
136
Display Messages
The memory is full. This may occur during fax
reception if too much data is received before the
pages can be printed out. If faxes have been received
to memory because printing is not possible (an
additional message will indicate the problem), resolve
the problem so that printing can continue (see
Substitue Reception to Memory in Chapter 4). If you
are attempting to transmit from memory, see Sending
Documents from Memory in Chapter 7.
MEMORY PRINTING
The fax is preparing or printing out a document from
memory.
NO DATA
This appears if you attempt to search for an
automatic dialling number when none have been
stored.
NO # STORED
You have tried to dial or clear a Rapid Key or Speed
Dial number that hasn't been programmed (a full
number hasn't been assigned to it).
OUT OF PAPER
You are out of printing paper (or the paper release
plate is open). Load paper as described in Loading
Printing Paper in Chapter 1.
ON HOOK DIAL
The SPEAKER key has been pressed and the fax is
waiting for you to dial. (To return to the date and time
display, press the SPEAKER key again.)
OVER HEAT
The print head has overheated. Operation may be
continued once it cools.
PAPER JAMMED
The printing paper is jammed. See the following
section, Clearing Paper Jams.
READY TO SEND
A document has been loaded and the fax is waiting
for transmission or copying instructions.
RECALLING
This appears if you attempt to send a fax by
automatic dialling and the line is busy or the receiving
fax machine does not answer. Your fax machine will
automatically reattempt the call. (See Automatic
Redialling in Sending a Fax by Automatic Dialling in
Chapter 3.)
11. Troubleshooting
MEMORY IS FULL
137
Display Messages
SEARCH DIAL
The HOLD/SEARCH key has been pressed. Press #
or * to search for an automatic dialling number, or
press STOP to return to the data and time display.
(See Using the HOLD/SEARCH key in Sending a
Fax by Automatic Dialling in Chapter 3.)
SET PAPER &/
PRESS START KEY
(alternating messages)
Check the printing paper. If the tray is empty, add
paper and then press the START/MEMORY key. If
there is paper in the tray, make sure it is inserted
correctly and then press the START/MEMORY key.
TOTAL PAGE(S) 01
Number of pages transmitted, received, or copied.
Audible signals
Continuous tone
3 seconds
Indicates the end of transmission,
reception, or copying.
Intermittent tone
(3 bleeps)
5 seconds
(1 seconds on,
1 seconds off)
Indicates incomplete transmission,
reception, or copying.
Rapid intermittent
tone
35 seconds
(0.7 seconds on,
0.3 seconds off)
Indicates that the handset is off hook.
138
Clearing Paper Jams
Clearing Paper Jams
Clearing a jammed document
If the original document doesn't feed properly during transmission or
copying, or DOCUMENT JAMMED appears in the display, first try
pressing the START/MEMORY key. If it doesn't feed out, remove it
as follows:
1
Open the operation panel by grasping
the finger hold and pulling up.
2
Remove the document.
3
Close the operation panel, making
sure it clicks into place.
11. Troubleshooting
Important:
Do not try to remove a document without opening the operation panel.
This may damage the feeder mechanism.
Click!
139
Clearing Paper Jams
Clearing jammed printing paper
1
Pull the paper release plate forward
and remove the paper.
2
Open the operation panel (grasp the
finger hold and pull up), and then pull
the release on the right side of the
machine forward to open the print
compartment cover.
3
Gently pull the jammed paper out of
the machine, making sure no torn
pieces of paper remain in the print
compartment or rollers.
140
4
Close the print compartment cover
(press down on both sides to make
sure it clicks into place), and then
close the operation panel.
5
Pull the paper release plate toward
you, reinsert the paper in the paper
tray and push the paper release plate
back down.
11. Troubleshooting
Clearing Paper Jams
If SET PAPER & PRESS START KEY appears in the display, make
sure the paper is inserted correctly and then press the START/
MEMORY key.
141
QUICK REFERENCE GUIDE
INSTALLATION
ENTERING YOUR NAME AND
NUMBER
2
1
Note: Imaging film and paper must be loaded
to perform the following operation.
1. Press:
TEL.
SET
TEL.
LIN
E
FUNCTION
3
Display shows:
OWN NUMBER SET
3
2. Press:
START/MEMORY
3. Enter your fax number (max. of 20 digits) by
pressing the number keys.
1. Connect the handset as shown.
• If you make a mistake, press the HOLD/
SEARCH key to move the cursor back to
the mistake, then enter the correct number
or letter.
2. Plug the power cord into a grounded, 230240 V outlet.
3. Plug one end of the telephone line into the
TEL. LINE socket on the rear of the fax and
the other end into the adapter. Plug the
adapter into a telephone wall socket.
4. Press:
RECORDING AN OUTGOING
MESSAGE
• To enter two letters in succession that
1. Press:
FUNCTION
0
Display shows: OGM RECORDING
2. Press:
START/MEMORY
3. Press 1 (GENERAL) to record an outgoing
message for the answering machine. Press
2 (TRANSFER) to record an outgoing
message for the Transfer function.
4. Pick up the handset, press the START/
MEMORY key, and speak into the handset
to record your message.
5. When finished, press the STOP key or
replace the handset.
STOP
6. Press:
STOP
START/MEMORY
5. Enter your name by pressing the appropriate
number keys as shown below.
require the same key, press the SPEAKER
key after entering the first letter.
A=
J=
B=
K=
T=
C=
L=
U=
D=
M=
V=
E=
N=
W=
S=
F=
O=
X=
G=
P=
Y=
H=
Q=
Z=
I=
R=
SPACE =
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
SPEED DIAL
REDIAL
HOLD/
SEARCH
SPEAKER
Deletes highlighted
letter.
Upper/lower case
shift key.
Moves cursor to the
left.
Moves cursor to the
right.
Press either key one or more times to select
and enter a symbol.
STOP
6. When finished, press:
START/MEMORY
142
Quick Reference Guide
SETTING THE DATE AND TIME
SENDING DOCUMENTS
Note: Imaging film and paper must be loaded
to perform the following operation.
Place your document (up
to 10 pages) face down in
the document feeder.
Press:
FUNCTION
3
Display shows: DATE & TIME SET
Press the START/MEMORY key:
START/MEMORY
Enter two digits for the Day (01 through 31).
Enter two digits for the Month (01 through 12).
Enter four digits for the Year (Ex: 2001).
Enter two digits for the Hour (00 through 23).
Enter two digits for the Minute (00 through 59).
STOP
When finished, press:
START/MEMORY
Normal Dialling
SPEAKER
1. Lift the handset or press
2. Dial the fax number.
3. Wait for the reception tone (if a person
answers, ask them to press their Start key)
4. Press:
START/MEMORY
Rapid Key Dialling
Press the appropriate Rapid Key.
Transmission will begin automatically.
Speed Dialling
STORING AND CLEARING
NUMBERS FOR AUTO DIALLING
1. Press:
Note: Imaging film and paper must be loaded
to perform the following operation.
2. Enter 2-digit Speed Dial number.
3. Press:
1. Press:
FUNCTION
3
SPEED DIAL
START/MEMORY
RECEIVING DOCUMENTS
TEL
Display shows:
FAX/TEL # MODE
2. Press 1 to store a number or 2 to clear a
number.
3. Enter a 2-digit Speed Dial number (from 01
to 08 for Rapid Key Dialling, or 09 to 88 for
Speed Dialling). If you are clearing a number,
go to Step 7.
4. Enter the full telephone/fax number.
5. Press:
TEL/FAX A.M.
START/MEMORY
TEL
FAX
14 OCT 10:30
Press:
TEL/FAX A.M.
TEL
FAX
14 OCT 10:30
TEL/FAX A.M.
TEL
FAX
14 OCT 10:30
TEL/FAX A.M.
FAX mode: The fax automatically answers on
two rings and receives the incoming document.
TEL mode:
Fax
tone
START/MEMORY
6. Enter the name of the location by pressing
number keys (max. of 20 characters). (Refer
to the letter entry table in ENTERING YOUR
NAME AND NUMBER.)
STOP
7. Press:
FAX
14 OCT 10:30
RECEPTION
MODE
START/MEMORY
RECEIVING
TEL/FAX mode:
The fax machine automatically answers on two
rings and receives faxes. Voice calls (including
manually dialled fax transmissions) are
signalled by a special ringing sound.
A.M. mode: Select this mode when you go out
to receive both voice messages and faxes.
143
Index
A
A.M. reception mode, 32, 79
Activity Report, 121
Automatic printing, 120
Anti junk fax, 105, 119
Anti Junk Number List, 125
Audible signals, 138
Auto cover sheet, 120
Automatic dialling, 72
Automatic dialling, storing numbers, 69
B
Batch page numbering, 103
Broadcasting, 98
C
Caller ID, 91
Caller ID list, 93, 126
Chain Dialling, 89
Cleaning, 128, 131
Contrast, 64
Copies, 85
Copy cut-off setting, 87
Copy/Help key, 12, 85
Cover sheet, 120
D
Date, setting, 29
Delete key, 11
Dial mode, 117
Dialling
Direct Keypad, 74
Normal, 66
Rapid Key, 72, 88
Search, 75, 89
Speed, 73, 88
144
Direct Keypad Dialling, 74
Display, 10
Display messages, 136
Distinctive Ring, 96
Document feeder, 62
Document guides, 62
Document restrictions, 61
Document rollers, 131
Document sizes, 60
Document, maximum scanning size, 61
E
ECM (Error Correction Mode), 120
Extension telephone
Connecting, 18
Using, 81
F
Fax Ability (Distinctive Ring), 96
Fax Duet (Distinctive Ring), 96
FAX reception mode, 32, 78
Fax reception on TAD failure, 44
Fax Signal Receive, 118
Fine Resolution Priority, 114
Four rings TEL answer, 115
Function key, 11
H
Halftone, 64
Handset, 14
Hold, 90
Hold/Search key, 11, 89
I
Imaging film, loading and replacing, 19
Incoming message time, 43
Index
J
Jams, clearing, 139
Junk fax number check, 119
L
Letters, entering, 27
Line error, 132
Loading printing paper, 24
Loading the document, 62
M
Memory
Sending documents from, 107
Substitute reception to, 84
Messages
Checking date and time, 42
Erasing, 41
Listening to, 40
Listening to remotely, 53
Setting allowed time, 43
N
Normal Dialling, 66
Number keys, 11
Number of rings in FAX and TEL/FAX
reception mode, 115
O
Option Setting List, 124
Outgoing message, 36
Override Ringing, 49
P
Panel release, 11
Paper jams, clearing, 139
Passcode List, 124
Pauses in automatic dialling, 69, 74
Play/Skip key, 10, 40
Polling, 109 - 111
Polling key, setting, 119
Print contrast setting, 25
Print head, cleaning, 128
Print Setup List, 127
Priority Call, 94
Pseudo ringing duration, 118
R
Rapid Dial keys, 11
Rapid Key Dialling, 72, 88
Rec/Memo key, 11
Reception mode
A.M. mode, 32, 79
FAX mode, 32, 78
Setting, 33
TAD mode, 39
TEL mode, 32, 80
TEL/FAX mode, 32, 77
Reception mode key, 10, 33
Reception Ratio setting, 83
Redial key, 10, 67
Redialling, 76, 89
Remote code number, 51
Remote operations, 51
Remote Reception Select, 116
Removing original document, 63
Repeat key, 10
Resolution, 64
Resolution key, 11
Ringing volume, 35
Rollers,cleaning, 131
S
Scanning glass, cleaning, 131
Search Dialling, 75, 89
Sender’s name and number, entering, 26
Speaker key, 11, 34, 66, 88
Speaker volume, 34
Speed Dial key, 10, 73, 88
Speed Dialling, 73, 88
145
Index
START/MEMORY key, 12
Stop key, 12
T
TAD reception mode, 39
TEL reception mode, 32, 80
TEL. SET socket, 18
TEL/FAX reception mode, 32, 77
Tel/Fax Remote Number, 116
Telephone Number List, 123
Telephone, using as, 88
146
Time, setting, 29
Timer List, 123
Timer operations, 112
Transaction Report, 127
Transaction Report Print Select, 117
Transfer Function, 46
Two-in-one printing, 82
V
Volume keys, 11, 34
REMOTE OPERATION CARD
The card below is provided as a quick guide to remote operation. Cut it out
and carry it with you when you go out.
Remote Operation Guide
1. Call your fax from a touch-tone telephone, and
press # when the outgoing message begins.
2. Enter your remote code:
.
3. Press # .
4. After listening to your messages, you can either
hang up to save them, or enter one of the commands on the reverse side.
REMOTE COMMANDS
• PLAYBACK
Play messages ................. 7
Move backward/repeat...... 2
Skip forward ...................... 5
Stop .................................. 0
Play new messages only .. 6
(first stop playback)
• ERASING MESSAGES
Erase single message ...... 3
Erase all messages .......... 3
• RECORDING A MEMO
Start .................................. *
End ................................... 0
• RECORDING A NEW OGM
Start .................................. 4
#
#
#
#
#
#
3 #
#
#
*
• FAX RECEPTION MODES
A.M. mode ........................
FAX mode.........................
TEL mode .........................
TEL/FAX mode .................
• TRANSFER FUNCTION
Turn on .............................
Turn off .............................
New transfer number ........
8
8
8
8
1
2
3
4
#
#
#
#
9 1 #
9 2 #
9 0 #
(Tel. #)
Record transfer OGM .......
To quickly disconnect........
• OGM ONLY MODE
Turn on .............................
Turn off .............................
#
9 3 #
* *
1 1 #
1 2 #
SHARP CORPORATION OF AUSTRALIA PTY.LTD.
A.C.N. 003 039 405
1 Huntingwood Drive, Huntingwood, Blacktown, N.S.W., 2148
SHARP CORPORATION OF NEW ZEALAND LIMITED.
Cnr Mahunga Drive & Hastie Ave. Mangere Bridge, Auckland
New Zealand
SHARP CORPORATION
PRINTED IN THAILAND
(TINSE4191XHTZ)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising