Crestron | IM-WCVP | Installation guide | Crestron IM-WCVP Installation guide

Crestron IM-WCVP Installation guide
Crestron IM-WCVP
iMedia Wall Plate Computer Center with
Video Control Panel
Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2006 Crestron Electronics, Inc.
Crestron IM-WCVP
iMedia Wall Plate Control Panel
Contents
iMedia Wall Plate Computer Center with Video Control
Panel: IM-WCVP
1
Introduction......................................................................................1
Features and Functions ..........................................................1
Application ............................................................................3
Specifications.........................................................................4
Physical Description ..............................................................5
Industry Compliance..............................................................7
Setup.................................................................................................8
Network Wiring .....................................................................8
Installation .............................................................................8
Hardware Hookup..................................................................9
System Configuration ............................................................9
Operation........................................................................................10
Problem Solving.............................................................................11
Troubleshooting...................................................................11
Reference Documents..........................................................13
Further Inquiries ..................................................................13
Future Updates.....................................................................13
Return and Warranty Policies ........................................................14
Merchandise Returns / Repair Service ................................14
CRESTRON Limited Warranty ..........................................14
Operations & Installation Guide – DOC. 6489
Contents • i
Crestron IM-WCVP
iMedia Wall Plate Control Panel
iMedia Wall Plate Computer
Center with Video Control Panel:
IM-WCVP
Introduction
Features and Functions
• Control panel for use with the IM-WCVI iMedia Wall Plate
Computer Center with Video Interface1
• Connects to IM-WCVI to create IM-WCCV-S Wall Plate
Computer Center with Video using CresCAT™-IM iMedia cable
or other high quality CAT5 cable (up to 40 feet) 2
• Controls volume, source selection, and power for iMedia systems
• Mounts in a standard, 2½ inch deep, single-gang electrical box
1. The IM-WCVP is part of the IM-WCCV-S. It must be used with the IM-WCVI.
2. For more information on CresCAT-IM cable, refer to the latest version of the
IM-WCVI guide (Doc. 6488), available from the Crestron website
(www.crestron.com/manuals).
The iMedia Transport
The iMedia transport utilizes a single CAT5e* type cable to transmit
computer RGB, video, and stereo audio signals to a single projector or
plasma display. A typical XGA signal (1024 X 768 pixels at 60Hz) can
be transmitted up to 84 feet using iMedia, while higher resolutions up to
1600 x 1200 can be handled over shorter distances. Composite video
signals can be transmitted up to 218 feet. Audio is transmitted digitally at
Operations & Installation Guide – DOC. 6489
iMedia Wall Plate Control Panel: IM-WCVP • 1
iMedia Wall Plate Control Panel
Crestron IM-WCVP
20-bit, 48 kHz resolution. Control and power signals are also contained
on the same wire, eliminating the need for separate control or power
cables.
*
For iMedia use CresCAT-IM cable, or quality CAT5e/CAT6 cable having a
maximum delay skew of 15ns per 100m.
2-Piece Wall Plate Multimedia Interface
The IM-WCCV-S is an iMedia (IM) transmitter featuring separate wall
plates for interface and control. The interface panel (IM-WCVI) is
designed to install in a standard 2-gang electrical box, providing video,
RGB, and stereo audio inputs for connection to the output of a computer
or AV source. The control panel (IM-WCVP) is a separate 1-gang wall
plate, which may be installed up to 40 feet from the interface panel.
Installing wiring for the IM-WCCV-S is extremely simple using
CRESCAT-IM cable. Up to three IM-WCCV-S's, or other IM
transmitters, may be installed as part of a complete system to provide
multiple input locations within the room.
Foolproof Operation
Every iMedia system is easy and intuitive to use. A simple press of the
VIDEO or PC buttons on the control panel selects the appropriate input,
turns on the projector (or plasma, etc.), lowers the screen or lift, and
routes all the signals where they need to go. The volume control affords
easy adjustment of the audio level, and the entire system can be turned
off at any time by simply holding down either button for five seconds.
For systems having more than one IM transmitter, selecting an input at a
given input location overrides the previously selected input at any other
location. The audio level for each input location is controlled individually
by its respective volume control.
2 • iMedia Wall Plate Control Panel: IM-WCVP
Operations & Installation Guide – DOC. 6489
Crestron IM-WCVP
iMedia Wall Plate Control Panel
Application
The IM-WCVP is part of the IM-WCCV-S iMedia transmitter. As shown
in the following diagram, iMedia transmitters provide input points for
video and PC sources on an iMedia receiver.
iMedia System Diagram
IM-TCCV
IM-WCCV
IM-WCCV-S
IM-FTCCV*
Computer
Video
iMedia
Transmitter
LAN
CresCAT-IM
IM-TCC
IM-WCC
IM-FTCC-B
IM-RXV1
IM-RXV3
Audio Amplifier
or Speakers
iMedia Receiver
Display Device
IR
RS-232
Control
Control
Screen/Lift
*IM-FTCCV available 3Q 2006
Operations & Installation Guide – DOC. 6489
Room Sensor
iMedia Wall Plate Control Panel: IM-WCVP • 3
iMedia Wall Plate Control Panel
Crestron IM-WCVP
Specifications
Specifications for the IM-WCVP are listed in the following table.
IM-WCVP Specifications
SPECIFICATION
Power Requirements
Environmental
Temperature
Humidity
Enclosure
Dimensions
Height
Width
Depth
Weight
4 • iMedia Wall Plate Control Panel: IM-WCVP
DETAILS
Power is provided by the iMedia
receiver via the IM transport
41° to 104°F (5° to 40°C)
10% to 90% RH
(non-condensing)
Requires 2.5 inch deep singlegang electrical box
4.50 in (11.43 cm)
2.75 in (6.99 cm)
2.70 in (6.86 cm)
6.2 oz (176 g)
Operations & Installation Guide – DOC. 6489
Crestron IM-WCVP
iMedia Wall Plate Control Panel
Physical Description
This section provides information on the connections, controls, and
indicators available on your IM-WCVP.
IM-WCVP Physical View
IM-WCVP Overall Dimensions
2.75 in.
(6.99 cm)
2.10 in.
(5.34 cm)
1
2
4
4.50 in.
(11.43 cm)
5
3
FRONT
2.70 in
(6.85 cm)
Operations & Installation Guide – DOC. 6489
REAR
iMedia Wall Plate Control Panel: IM-WCVP • 5
iMedia Wall Plate Control Panel
Crestron IM-WCVP
Connectors, Controls, & Indicators
*
#
CONNECTORS,
CONTROLS, &
INDICATORS
DESCRIPTION
1
VOLUME
CONTROL KNOB
Turn clockwise to raise the volume of
the selected input; turn
counterclockwise to lower the volume
of the selected input.
2
VIDEO BUTTON
3
PC BUTTON
4
GROUND WIRE
5
TO IM-WCVI
Turns on the system and selects the
source connected to the VIDEO input
of the IM-WCVI.*
Turns on the system and selects the
source connected to the PC input of
the IM-WCVI.*
Connect the flying lead to earth
ground.
Female RJ-45 port to connect to
IM-WCVI over CresCAT-IM wire or
other high-quality CAT5 wire (40 feet
maximum).
Refer to “Operation” on page 10 for more information.
6 • iMedia Wall Plate Control Panel: IM-WCVP
Operations & Installation Guide – DOC. 6489
Crestron IM-WCVP
iMedia Wall Plate Control Panel
Industry Compliance
As of the date of manufacture, the IM-WCVP has been tested and found
to comply with specifications for CE marking and standards per EMC
and Radiocommunications Compliance Labelling.
NOTE: This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Operations & Installation Guide – DOC. 6489
iMedia Wall Plate Control Panel: IM-WCVP • 7
iMedia Wall Plate Control Panel
Crestron IM-WCVP
Setup
Network Wiring
When wiring the network, consider the following:
• Use Crestron Certified Wire.
• Use Crestron power supplies for Crestron equipment.
Installation
The IM-WCVP is designed to mount in a standard 2.5-inch (6.35 cm)
deep, single-gang, electrical box.
Required Tools:
• Phillips screwdriver
Mounting Parts Supplied with the IM-WCVP
PART DESCRIPTION
QUANTITY
Screw #6-32 x 1 in, Flat Head, Phillips
2
Installation in a Single-Gang Electrical Box
NOTE: Run iMedia wire
through the top or
bottom of the
electrical box.
2.5 in. Depth,
Single-Gang
Electrical Box
8 • iMedia Wall Plate Control Panel: IM-WCVP
#6-32 x 1 in.
Screws
Operations & Installation Guide – DOC. 6489
Crestron IM-WCVP
iMedia Wall Plate Control Panel
Hardware Hookup
Ventilation
To prevent overheating, do not operate this product in an area that
exceeds the environmental temperature range listed in the table of
specifications. Consideration must be given if installed in a closed or
multi-unit rack assembly since the operating ambient temperature of the
rack environment may be greater than the room ambient. Contact with
thermal insulating materials should be avoided on all sides of the unit.
Connect the
Device
Make the necessary connections as called out in the illustration that
follows this paragraph. Turn on the system only after all connections
have been made.
Hardware Connections for the IM-WCVP
TO IM-WCVI:
CRESCAT-IM
CONNECTION
TO IM-WCVI
GROUND
REAR
NOTE: For optimum performance, Crestron strongly recommends using
CRESCAT-IM cable, available from Crestron. Other high-quality/low
skew CAT5e/CAT6 wiring may also be used with varying performance.
The maximum cable length between the IM-WCVP and the IM-WCVI is
40 feet.
System Configuration
Refer to the latest version of the IM-RXV1 & IM-RXV3 guide (Doc.
6478), available from the Crestron website for iMedia system
configuration instructions.
Operations & Installation Guide – DOC. 6489
iMedia Wall Plate Control Panel: IM-WCVP • 9
iMedia Wall Plate Control Panel
Crestron IM-WCVP
Operation
The IM-WCVP can be used to turn a system on or off, select a source, or
adjust volume.
Turn on the
System
Press the PC button to turn on the system with the PC signals routed to
the iMedia receiver or press the VIDEO button to turn on the system
with the video signals routed to the iMedia receiver. The associated LED
will light to indicate the selected source.
Select a
Source
Press the PC button to route PC signals to the iMedia receiver or press
the VIDEO button to route video signals to the iMedia receiver The
associated LED will light to indicate the selected source.
Adjust Volume
Turn the volume knob clockwise to raise the volume of the selected
input; turn counterclockwise to lower the volume of the selected input.
Turn off the
System
Press and hold the selected source button for five seconds. The source
button LED will flash and then turn off.
10 • iMedia Wall Plate Control Panel: IM-WCVP Operations & Installation Guide – DOC. 6489
Crestron IM-WCVP
iMedia Wall Plate Control Panel
Problem Solving
Troubleshooting
The following table provides corrective action for possible trouble
situations. If further assistance is required, please contact a Crestron
customer service representative.
IM-WCVP Troubleshooting
TROUBLE
SOURCE
LED does
not
illuminate.
POSSIBLE
CAUSE(S)
Not receiving
power.
Incorrect
power supply.
Source is not
selected.
No video
output
displayed.
Incorrect cable
connection.
CORRECTIVE
ACTION
Verify that the
iMedia cable is
connected to the
IM-WCVI and the
IM-WCVI is
connected to the
iMedia receiver.
Only use Crestron
power supplies.
Push a source
button to select a
source.
Verify computer
cable connection.
Verify video cable
connection.
Verify iMedia
output cable
connection is
secure.
(Continued on following page)
Operations & Installation Guide – DOC. 6489 iMedia Wall Plate Control Panel: IM-WCVP • 11
iMedia Wall Plate Control Panel
Crestron IM-WCVP
IM-WCVP Troubleshooting (Continued)
TROUBLE
POSSIBLE
CAUSE(S)
CORRECTIVE
ACTION
No audio
output.
Incorrect cable
connection.
Video from
RGB source
is garbled or
no output.
Incorrect cable
connections.
Button does
not function
when
pressed.
Incorrect cable
connection.
Other
functions
operate, but
does not
control the
projector.
Incorrect
connections to
projector.
Verify computer
audio cable
connection.
Verify video input’s
audio cable
connection.
Verify 15-pin
computer cable
connection. Verify
iMedia output cable
connections.
Verify maximum
iMedia cable
length. Adjust delay
on iMedia receiver.
Verify that the
iMedia output cable
connection from
the IM-WCVI to the
iMedia receiver is
secure.
Verify cable wiring
and connections
between receiver
and projector.
12 • iMedia Wall Plate Control Panel: IM-WCVP Operations & Installation Guide – DOC. 6489
Crestron IM-WCVP
iMedia Wall Plate Control Panel
Reference Documents
The latest version of all documents mentioned within the guide can be
obtained from the Crestron website (http://www.crestron.com/manuals).
This link will provide a list of product manuals arranged in alphabetical
order by model number.
List of Related Reference
DOCUMENT TITLE
IM-RXV1 & IM-RXV3 iMedia Receiver/Processor with Video
IM-WCVI iMedia Wall Plate Computer Center Interface with
Video
Further Inquiries
If you cannot locate specific information or have questions after
reviewing this guide, please take advantage of Crestron's award winning
customer service team by calling the Crestron corporate headquarters at
1-888-CRESTRON [1-888-273-7876]. For assistance in your local time
zone, refer to the Crestron website (http://www.crestron.com/) for a
listing of Crestron worldwide offices.
You can also log onto the online help section of the Crestron website to
ask questions about Crestron products. First-time users will need to
establish a user account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features, and extends the
capabilities of the IM-WCVP, additional information may be made
available as manual updates. These updates are solely electronic and
serve as intermediary supplements prior to the release of a complete
technical documentation revision.
Check the Crestron website periodically for manual update availability
and its relevance. Updates are identified as an “Addendum” in the
Download column.
Operations & Installation Guide – DOC. 6489 iMedia Wall Plate Control Panel: IM-WCVP • 13
iMedia Wall Plate Control Panel
Crestron IM-WCVP
Return and Warranty Policies
Merchandise Returns / Repair Service
1.
No merchandise may be returned for credit, exchange, or service without prior authorization
from CRESTRON. To obtain warranty service for CRESTRON products, contact an
authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory
and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying
the nature of the problem, name and phone number of contact person, RMA number, and
return address.
2.
Products may be returned for credit, exchange, or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with
RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect
or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its
sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any
products returned with an RMA.
3.
Return freight charges following repair of items under warranty shall be paid by CRESTRON,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials
and workmanship under normal use for a period of three (3) years from the date of purchase from
CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical
parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and
overlay components are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON
dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if
any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended, or if it has been subjected to misuse, accidental
damage, modification, or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages
inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a
third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or
labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or
implied, nor authorizes any other party to offer any warranty, including any implied warranties of
merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are
limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.
Trademark Information
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered trademark
of Microsoft Corporation. Windows95/98/Me/XP and WindowsNT/2000 are trademarks of Microsoft Corporation.
14 • iMedia Wall Plate Control Panel: IM-WCVP Operations & Installation Guide – DOC. 6489
Crestron IM-WCVP
iMedia Wall Plate Control Panel
This page is intentionally left blank.
Operations & Installation Guide – DOC. 6489 iMedia Wall Plate Control Panel: IM-WCVP • 15
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Operations & Installation Guide – DOC. 6489
(2015097)
05.06
Specifications subject to
change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising