Comet Gas Equipment Blowpipes & Cutters

Comet Gas Equipment Blowpipes & Cutters
Comet Blowpipes
Cutting Attachments
and Consumables
GEQBCC Rev 1
1300 654 674
I
www.cigweld.com.au
Introduction
CIGWELD Professional:
when welding is your business
At CIGWELD we distinguish ourselves from our competition through
superior featured, dependable products, technical innovation and
excellence in customer service and technical support.
Our Professional COMET Blowpipe and Cutting Attachment range is
proof of this commitment to deliver quality equipment that exceeds
expectations. A wealth of features and options make this equipment
the perfect choice for the serious welding professional.
CIGWELD COMET 3 Blowpipe System
The COMET 3 Blowpipe System offers a range of gas equipment
that is well renowned for its safety and performance excellence and
features flexible multi-fuel and multi-process capability.
The system is made up of the COMET 3 Blowpipe and attachments,
together with a broad range of accessories to cover the wide variety
of welding, cutting and heating applications using Oxy-Acetylene,
Oxy-LPG or Natural Gas.
For gas welding and brazing, there is a range of swaged welding tips
to cater for the smallest sheet metal welding job up to 12mm plate
thickness. The extensive cutting nozzle range covers applications
such as standard cutting, rivet cutting, gouging, sheet metal cutting
and heating.
COMET Gas equipment complies with Australian Standard AS4839 –
2001 “The safe use of portable and mobile oxy-fuel gas systems for
welding, cutting, heating and allied processes”. The standard specifies
the selection, operation and maintenance procedures for oxy-fuel hand
held or portable equipment and addresses many issues concerning its
everyday use.
The experience gained and commitment to manufacturing products
of unrivalled quality has allowed CIGWELD to become the recognised
industry standard and continues to be by far the market leader in
Australia and near Pacific regions.
So don’t compromise!
Insist on COMET to get the job done right . . . every time!
©2012 Victor Technologies. All rights reserved.
Contents & Key to Icons
COMET 3 Blowpipe System
4
Blowpipes
6
COMET 3 Blowpipe - Heavy Duty
6
COMET 3 Mixer
7
Cutting Attachments
8
COMET 3 Heavy Duty Cutting Attachment
8
COMET Multi-purpose Cutting Torch
10
Nozzles
11
COMET Taper Seat Cutting Nozzles
11
COMET Type 41 Cutting Nozzles
12
COMET Type 44 Cutting Nozzles
13
COLT Type 90 Cutting Nozzles
14
3-Seat Cutting Nozzles (Machine Cutting)
15
Welding & Heating Tips
16
COMET Oxy/Acetylene Welding Tips
16
COMET Oxy/LP Gas Brazing Tips
16
COLT Sheetmetal Welding, Brazing & Heating Tips
16
COMET Superheating Tips - Oxy/Acetylene
17
COMET Superheating Tips - Oxy/LP Gas
18
Accessories
19
COMET Superheating Barrels
19
Air Fuel Tips
19
Key to Icons
5
YEAR
Warranty: This equipment is manufactured to stringent CIGWELD quality
standards and is backed by a conditional warranty period as indicated.
Valve-in-Valve
Suitable for cutting
Suitable for heating
Suitable for welding/brazing
3
COMET 3 Blowpipe System
Acetylene Swaged
Welding Tips
LP Gas Swaged Welding
Tips
Size 32 307006
Size 26 307005
Size 15 307059
Size 8 307068
Size 20 307004
Size 15 307003
Nozzles
Size 12 307002
Heating Heating
Acetylene LP Gas
Size 10 307001
Rivet
Cutting
Gouging
Acetylene
Sheet
Metal
Cutting
Cutting Gouging
LP Gas Acetylene Acetylene
Size 8 307000
Size 6 307057
Size 4 307056
Acetylene
Heating Tips
SHA1
307121
Roller Guide
Radius Bar
308729
308752
SHA2
307122
LP Gas
Heating Tips
Barrels
450mm 307124
700mm 307125
SHP1
307120
SHP2
307119
735mm 307123
LP Gas
Heating Tips
450mm 307124
700mm 307125
SHP3
307118
4
SHP4
307117
735mm 307123
Gouging
LP Gas
COMET 3 Blowpipe System
COMET Accessories
Welding
Mixer 10mm (3/8”) Type 550
304002
COMET Gas Kit Toolbox
308888
Cutting
Gouging
Gas Economiser (Acet or LP Gas)
308503
Heating
COMET 3 Cutting Attachment (Multi Fuel)
304005
Flint Lighter
308789
Three Flint Lighter
308832
Heating
Heating Tip
307007
Electronic Lighter
Mixer 10mm (3/8”) Type 550
308700
304002
COMET 3 Blowpipe
304001
F6-308777
F6-308778
Mixer 13mm (1/2”) Type 570
304003
Super Heating
F2B-308854
COMET Blowpipe Mounted
Flashback Arrestors
Injector 13mm (1/2”) LP Gas/Natural Gas Type 574
304166
F2B-308853
F6Q Quick-Connect
308363
F6Q Quick-Connect
308362
85-10B-308861
85-10B-308862
5
Blowpipes
COMET 3 Blowpipe - Heavy Duty
5
YEAR
Features and Benefits
Two-stage valves give precise gas control from the
smallest welding tip to the largest heating tip.
Permits fine sensitive control for delicate welding
jobs and easy lighting up, to flows of up to 600
l/min for the heaviest heating job.
A non-rotating valve spindle drastically minimises
wear.
Due to ‘O’ ring seals, only hand tightening is
required to connect the mixer or cutting attachment
to the handle.
Locking teeth secure re-positioning with hand
tightening.
Handle shape gives comfortable positive grip.
Left hand/right hand threads prevent incorrect hose
connection.
Colour coded control knobs are fitted for maximum
safety and ease of operation, even when wearing
welding gloves.
Can be purchased as a single item or as part of a
cutting and welding outfit.
The COMET 3 Blowpipe when used with appropriate attachments is suitable for
fusion welding, brazing, soldering, heating, hand cutting, sheet metal cutting
and rivet cutting.
Specifications
Part No:
Description
Fuel gas type
Connections
Weight
304001
COMET 3 Blowpipe
All
5/8”-18UNF
620g
Spare Parts
Control valve kit
Part No: 304009
Handle halves kit
Part No: 304012
Small seat open; Large seat closed
Spring prevents large seat from opening while
adjustment is made with small seat. This gives
exceptionally sensitive control for fine flame adjustment.
NOTE: To protect your product warranty and to ensure a safe, quality
repair, use a CIGWELD Accredited Gas Service Provider.
valve in valve
Both seats open for large flows
When the small seat opens fully the large seat then
starts to operate, quickly providing large flows to
approximately 130 l/min (270 cu ft/h) of acetylene and
oxygen in approximately one turn. Immediate springloaded seat is free to rotate, saving wear on fixed seat.
6
Blowpipes
COMET 3 Mixer
5
YEAR
Features and Benefits
Hand tightening for easy attachment onto COMET 3
Blowpipe. (‘0’ ring seals ensure a perfect gas-tight
connection every time).
Type 550
Large flutes on mixer give easy positive handling,
even when wearing welding gloves.
Mixer 550 and 570 can be used with either
Oxy/Acetylene, Oxy/LP gas or Oxy/Natural gas.
Mixer 574 is an injector mixer design for Oxy/LP
gas or Oxy/Natural gas and used for heavy duty
Type 570
high flow applications. For use with SHP3 and
SHP4 superheating tips only.
No change required when altering fuel gas, other
than the type of tip, hose and regulator required.
Offers high resistance to backfire, regardless of the
gas type or flow setting.
Type 574
Mixer 550 is used for welding and light heating. Mixer 570 and 574 are used
for heavy heating applications.
Spare Parts
Small O-ring for attach/mixer
Part No: 7964006
Large O-ring for attach/mixer
Part No: OR28
O-ring kit
Part No: 304013
NOTE: To protect your product warranty and to ensure a safe, quality
repair, use a CIGWELD Accredited Gas Service Repair Provider.
Specifications
Part No:
Description
Fuel gas
type
Welding
capacity
Weight
304002
COMET 3 Mixer
Type 550
All
up to 25mm
165g
304003
COMET 3 Mixer
Type 570
All
–
163g
304166
COMET 3 Mixer
Type 574
LP/Nat Gas
–
278g
7
Cutting Attachments
COMET 3 Heavy Duty Cutting Attachment
5
YEAR
Features and Benefits
Attaches quickly and easily to COMET 3 Blowpipe
by hand (no spanner required).
“Locking teeth” enable the attachment to be
re-positioned.
Tapered seat head allows multi-positioning of
gouging nozzle.
Cutting oxygen lever securely fitted to the body for
ease of operation.
Twin tube construction gives good visibility.
Unique multi-mixer design accommodates
Oxy/Acetylene, Oxy/LP gas or Oxy/Natural gas.
Large flutes on hand tightening nut for a better
grip when wearing welding gloves.
For use with type 40 nozzles.
Suitable for the following processes: hand cutting, sheet metal cutting, rivet
cutting, heating and gouging.
Spare Parts
Control valve kit
Part No: 304010
Cutting Oxygen valve kit
Part No: 304015
Lever replacement kit
Part No: 304011
Nozzle nut
Part No: 304014
Large O-ring for attach/mixer
Part No: OR28
Small O-ring for attach/mixer
Part No: 7964006
O-ring kit
Part No: 304013
NOTE: To protect your product warranty and to ensure a safe, quality
repair, use a CIGWELD Accredited Gas Service Repair Provider.
8
Specifications
Part No:
Description
304005 COMET 3 Cutting
Attachment HD
Fuel gas
type
All
Cutting
capacity
Cutting
nozzle
up to 150mm Type 41 & 44
Weight
633g
Cutting Attachments
COMET Multipurpose Cutting Torch
5
YEAR
Features and Benefits
Heavy duty manganese bronze head, designed to
resist tough environmental working conditions.
Gas mixing takes place in the blowpipe head,
providing the operator with maximum protection
against the unlikely occurrence of backfires or
flashbacks.
520mm
Stainless steel triangular tube construction,
provides the ultimate in strength.
Lightweight aluminium handle, which has been
treated to minimise corrosion in the working
900mm
environment. Brass handle for extra strength and
mining operation.
Stainless steel cutting oxygen lever, incorporating
a locking button for extended cutting, gouging or
heating.
520mm
Spare Parts
Description
Part No.
Control valve kit
304074
Lever replacement kit
304140
Acetylene mixer kit
CB148
Suitable for the majority of heavy-duty cutting and gouging processes. The
LP gas/Natural gas mixer kit
CB152
cutting oxygen valve has been designed to allow flow control from slow bleed to
Nozzle nut
304014
full capacity - ideal for piercing work. Inlet connection filters prevent foreign
NOTE: To protect your product warranty and to ensure a safe, quality
repair, use a CIGWELD Accredited Gas Service Provider.
particles entering the blowpipe, which reduces valve seat wear and the chance
of blowpipe blockage. Each blowpipe comes factory set for use with acetylene
fuel gas and includes a separate mixer kit to change fuel gases from Acetylene
to LP gas or Natural gas. CIGWELD recommends this conversion should be
conducted by a CIGWELD Accredited Gas Service Provider.
Specifications
Part No:
Description
Fuel gas
type
Handle
Length
Head
Cutting
capacity
Cutting
nozzles
Connections
Weight
304141 COMET Multipurpose
All
Aluminium
520mm
90˚
Up to 300mm
Type 41 & 44
5/8”-18UNF
1.6kg
304161 COMET Multipurpose
All
Brass
520mm
90˚
Up to 300mm
Type 41 & 44
5/8”-18UNF
1.6kg
304143 COMET Multipurpose
All
Aluminium
900mm
180˚
Up to 300mm
Type 41 & 44
5/8”-18UNF
2.2kg
Extended lengths are available at your local CIGWELD Accredited Gas Service Provider
9
Nozzles
COMET Taper Seat Cutting Nozzles
Nozzles are the vital component of flame cutting
equipment. They provide the preheating flames to raise
Standard Nozzles
the steel to ignition temperatures and direct the jet of
CIGWELD standard taper seat nozzles are primarily designed for hand cutting
oxygen on to the heated area to perform the cutting
and precision machine cutting. The number of preheat holes provide for a better
process. To achieve this result in the most efficient
distribution of the preheat flames required in profile cutting. Standard nozzles
way, COMET nozzles have the following features:
produce a very uniform kerf surface and kerf width under any recommended
Longer nozzle life - the high brass content and
conditions.
advanced manufacturing techniques give COMET taper
seat nozzles an in-built quality.
One piece Acetylene nozzle
Better quality cutting - the mirror smooth finish of the
gas ports assures stable gas flows and superior
cutting oxygen stream. Cuts are clean smooth with the
narrowest kerf width.
Less slag adhesion - high copper content of sizes 20,
24 etc. conducts heat away from the nozzles face. The
nozzle keeps relatively cool and slag adherence to the
nozzle face is reduced.
LPG (propane) flames do not blow off - taper seat LPG
nozzles have slotted preheat ports which cause a
turbulence in the gas flow enabling the flame to hang
on to the nozzle.
Two piece LP gas nozzle
Hi-Speed Nozzles
Where speed is the prime consideration,
when machine cutting eg. in plate splitting
operations, Hi-Speed nozzles offer very
definite economies. Hi-Speed nozzles cut
expansion of
cutting oxygen
and consequently less cutting oxygen is
required. Gas savings of between 20% and
40% per metre of steel cut are consistently
bent nozzles. Only one nut is tightened to give perfect
gained with up to 50% increase in cutting
seating with taper seat nozzles.
speed, with no loss of quality.
consistent high quality performance.
Uncontrolled
a narrower kerf, less metal is consumed
Faster nozzle attachment - easy change of position for
Individual flame testing of COMET nozzles guarantees
Standard Tip
Hi-Speed Tip
Cutting oxygen
controlled in
tapered passage
Maintenance Instructions for Nozzles
Small sizes of taper seat acetylene nozzles are
Do not mistreat the nozzle. Do not use it as a hammer or as a lever to pry away
machined from high quality brass so that the small
cut portions of metal.
preheat holes will withstand continuous cleaning.
To clear the orifices, special nozzle cleaning reamers are obtainable from
Brass nozzles stay better longer for these moderate
CIGWELD Distributors.
heat applications. In all nozzles preheat gas
consumption is reduced because high velocity preheat
ports ensure that the flame travels at high speed from
the exit ports to the work. Wider seating areas ensures
gas tight seals with less tightening.
It is strongly recommended that these be used in preference to other means.
Should nozzle cleaning reamers not be available, then use a drill one size smaller
than the orifice and work it up and down without twisting. The drill should be held
in a pin vice, if it does not enter easily, start with a smaller drill with the same
procedure, increasing the size of drill until the correct size is used.
It is most important that the small holes at the seating end of the nozzles are not
enlarged in any way.
NOTE: Effective preheat flame shape and cutting oxygen can only be maintained when the edges of the
orifice are sharp and square. If a nozzle becomes damaged on the end, rub it down with a piece of fine
emery paper over a plate of glass, holding the nozzle at right angels to the glass. The orifices should be
cleaned out as described above. Provision is made in the design of the nozzle to make reconditioning
possible, as much as 3mm may be removed before the nozzle becomes unserviceable.
DO NOT use old pieces of wire, reamers or brooches to clean out pre-heat and cutting stream orifices.
DO NOT interfere in any way with the seating surfaces either on the nozzles or in the blowpipe head.
10
Nozzles
COMET Type 41 Cutting Nozzles
Oxy/Acetylene specifications
Standard speed cutting nozzles
CIGWELD Part No. Size Plate
Fuel gas flow
Total Oxygen
Type 41
thickness l/[email protected] flow & pressure
l/[email protected]
Standard: 306046 6
1-6
2.0
11(200)
for use
306047 8
6-10
3.5
20(200)
with
306048 12
12-20
4.0
38(200)
COMET 3 306049 15
25-75
7.0
75(350)
and Multi- 306050 20 100-125
9.0
134(400)
purpose 306051* 24 150-200
12.5
232(500)
306052* 32± 225-300
20.0
420(600)
306053* 48± 300-400
45.0
945(650)
Hi-speed speed cutting nozzles
CIGWELD Part No. Size Plate
Fuel gas flow
Total Oxygen Cutting speed
Type 41
thickness l/[email protected] flow & pressure mm/min†
l/[email protected]
Hi-speed: 306069 6HS
6-8
6.0
31(650)
700
for use
306070 8HS
8-20
6.0
50(650)
700-550
with
306071 12HS 25-75
10.0
107(650)
500-300
cutting
306072 15HS 75-150
12.0
158(650)
300-200
machines 306073* 20HS 150-250
13.0
250(650)
200-100
306074* 24HS 250-300
18.0
320(650)
90
NOTE: Preheat oxygen pressure for all hi-speed nozzles = 200kPa
Gouging nozzles
CIGWELD
Type 41
Part No.
Size
Fuel gas flow
l/[email protected]
Gouging:
for use with
COMET 3 and
Multipurpose
306035
306036*
306037*
306038
306077
32GB
48GB±
64GB±
32GS
60DG
15.0
18.0
20.0
15.0
Total Oxygen
flow & pressure
l/[email protected]
61(500)
85(600)
112(650)
61(500)
Sheet metal nozzle
CIGWELD
Type 41
Part No.
Size
Fuel gas flow
l/[email protected]
Sheet Metal:
for use with
COMET 3 and
Multipurpose
306067
6SM
1.5
Total Oxygen
flow & pressure
l/[email protected]
9(200)
Rivet cutting nozzle
CIGWELD
Type 41
Part No.
Size
Fuel gas flow
l/[email protected]
Rivet Cutting:
for use with
306076*
15RC
10.0
Total Oxygen
flow & pressure
l/[email protected]
80(400)
* Manufactured from copper
COMET 3 and
± For use with COMET Multi-Purpose ONLY
Multipurpose
† Cutting speeds are average values for drop cuts on clean plate with nozzles
in good condition-variations could be expected due to actual working conditions.
NB: Cutting nozzles can operate over a range of gas flows (hence plate thicknesses). The values indicated are typical operating conditions & can be increased or decreased to suit particular applications.
11
Nozzles
COMET Type 44 Cutting Nozzles
Oxy/LP gas or Natural gas specifications
Standard speed cutting nozzles
CIGWELD Part No. Size Plate
Fuel gas flow
Type 44
thickness l/[email protected]
Standard:
for use
with
COMET 3
and
Multipurpose
306025 6
306026 8
306028 12
306029 15
306030 20
306031 24
306032 32±
3-6
6-12
12-20
25-75
100-125
150-200
225-300
2.0
3.5
4.5
5.5
6.5
9.0
14.0
Total Oxygen
flow & pressure
l/[email protected]
17(200)
30(200)
58(250)
99(400)
171(400)
256(500)
456(600)
Hi-speed speed cutting nozzles
CIGWELD Part No. Size Plate
Fuel gas flow
Type 44
thickness l/[email protected]
Hi-speed:
for use on
cutting
machines
306018
306019
306021
306022
306023
306024
6HS
6-8
8HS
8-20
12HS 25-75
15HS 75-150
20HS 150-250
24HS 250-300
5.0
5.0
6.5
7.0
8.0
12.0
Total Oxygen Cutting speed
flow & pressure mm/min†
l/[email protected]
45(650)
550
64(650)
550-500
122(650)
500-300
173(650)
300-200
267(650)
200-100
350(650)
90
NOTE: Pre-heat oxygen pressure for all hi-speed nozzles = 200kPa
Gouging nozzles
CIGWELD Part No. Size
Type 44
Gouging: 306033
for use
306054
with
306055
COMET 3 306056
and
Multipurpose
32GS
32GB
48GB±
64GB±
DG= Deep Gouging
GB= Gouging - Bent
GS= Gouging - Straight
SM= Sheet Metal
RC= Rivet Cutting
HS= High Speed
± For use with COMET Multi-Purpose only
† Cutting speeds are average values for drop cuts on clean plate with nozzles in good condition - variations could be
expected due to actual working conditions.
NB. Cutting nozzles can operate over a range of gas flows (hence plate thicknesses).
The values indicated are typical operating conditions and can be increased or decreased to suit particular applications.
12
Fuel gas flow
l/[email protected]
12.0
12.0
13.0
15.0
Total Oxygen
flow & pressure
l/[email protected]
94(500)
94(500)
120(600)
150(650)
Nozzles
3 Seat Cutting Nozzles - Machine Cutting
Features and Benefits
Small Kerf.
Limited under and upper edge slag.
Limited upper edge melt.
Cutting operation with high speed.
Steady and safe cutting operation.
Cutting operation with small amount of gas.
High speed divergent nozzles with stainless steel
insert for improved performance and nozzle life.
Oxy/Acetylene specifications
Standard speed cutting nozzles
Part No. Plate Tip No. Cutting
Oxygen kPa
thickness(mm) size speed (mm) Cutting PR-Heat
306114
-5
00
-600
140
140
306115
5-10
0
660-550
200
200
306116 10-15
1
550-490
280
280
306117 15-30
2
490-400
300
300
306118 30-40
3
400-350
300
300
306119 40-50
4
350-320
300
300
306120 50-100
5
320-200
400
400
306121 100-150
6
200-150
450
450
306122 150-250
7
150-80
450
450
306123 250-300
8
80-45
450
450
Fuel
kPa
20
20
20
20
20
25
35
40
40
40
Kerf
width (mm)
1.0
1.3
1.8
2.0
2.3
2.8
3.0
3.6
4.1
4.3
Fuel
kPa
20
20
20
20
20
25
35
Kerf
width (mm)
0.8
1.3
1.3
1.8
2.0
2.6
2.8
Fuel
kPa
20
20
20
20
25
35
40
Kerf
width (mm)
1.3
1.8
2.0
2.3
2.8
3.0
3.6
Fuel
kPa
20
20
20
20
20
25
35
40
40
Kerf
width (mm)
0.8
1.3
1.3
1.8
2.0
2.6
2.8
3.6
4.6
Hi-speed cutting nozzles
CIGWELD has a long established relationship with Koike
Senso in Japan. Koike has developed a world-wide
reputation as a leading manufacturer of gas cutting
machines. Much of this reputation stems from their
ability to manufacture cutting nozzles of the highest
quality specifically for use with cutting machines, for
example koike high speed cutting nozzles are a divergent
type with a stainless steel insert screwed into the tip end
Part No. Plate Tip No. Cutting
Oxygen kPa
thickness(mm) size speed (mm) Cutting PR-Heat
306124
-5
00
-750
700
140
306125
5-10
0
700-680
700
200
306126 10-15
1
680-600
700
280
306127 15-30
2
600-500
700
300
306128 30-40
3
500-450
700
300
306129 40-50
4
450-400
700
300
306130 50-100
5
400-260
700
400
of the cutting oxygen port. This maintains a constant
Oxy/LP gas or Natural gas specifications
high quality cutting performance that also improves
Standard speed cutting nozzles
nozzle life up to 5 times that of a conventional nozzle.
Oxy/Acetylene cutting nozzle
Part No. Plate Tip No. Cutting
Oxygen kPa
thickness(mm) size speed (mm) Cutting PR-Heat
306097
5-10
0
660-550
210
200
306098 10-15
1
550-490
280
280
306099 15-30
2
490-400
315
315
306100 30-40
3
400-350
315
315
306101 40-50
4
350-320
315
315
306102 50-100
5
320-200
385
385
306103 100-150
6
200-150
455
455
Hi-speed cutting nozzles
Oxy/LP gas cutting nozzle
Part No. Plate Tip No. Cutting
Oxygen kPa
thickness(mm) size speed (mm) Cutting PR-Heat
306104
-5
00
-750
700
140
306105
5-10
0
700-680
700
200
306106 10-15
1
680-600
700
280
306107 15-30
2
600-500
700
315
306108 30-40
3
500-450
700
315
306109 40-50
4
450-400
700
315
306110 50-100
5
400-260
700
485
306111 100-150
6
260-180
700
455
306112 150-250
7
180-110
700
455
13
Welding & Heating Tips
COMET Oxy/Acetylene Welding Tips
Type 551 specifications
Size 32
Size 26
Size 20
Size 15
Size 12
Size 10
Size 8
Size 6
Size 4
Part
No.
307056
307057
307000
307001
307002
307003
307004
307005
307006
307026
Model Tip
Steel
Pressure kPa
No. size thickness(mm) oxygen
551
4
0.9
50
551
6
1.2
50
551
8
2.0
50
551
10
2.6
50
551
12
3.2-4.0
50
551
15
5.0-6.5
50
551
20 8.2-10.0
50
551
26
13-19
50
551
32
25
100
551 8-32 2.0-25
-
Pressure kPa Consumption
acetylene each gas (l/min)
50
1.5
50
1.5
50
2.0
50
3.0
50
4.0
50
6.5
50
12.0
50
22.0
100
38.0
-
COMET Oxy/LP Gas Brazing Tips
Type 554 specifications
Size 15
Size 8
14
Part Model Tip
Steel
Pressure kPa
No.
No. size thickness(mm) oxygen
307068 554
8
2.0
50
307059 554
15
5.0-6.5
50
Pressure kPa
LP Gas
50
50
Welding & Heating Tips
COMET Superheating Tips - Oxy/Acetylene
Features and Benefits
Part No. 307007
Concentrated high temperature heat.
Compact simple design for ease of cleaning.
Heavy copper construction helps conduct heat
away from the tip face, keeps the tip cool and
prevents flashbacks.
A small projection in the middle of the tip face
(307007, SHA1 and SHA2) prevents backfires
should the tip be inadvertently touched on the job.
Spanner adjustment flats milled into tip.
Gas pressure and identification stamped on every
SHA tip.
WARNING: at no time should the withdrawal rate of an individual
acetylene cylinder exceed 1/7 of the cylinder contents per hour. If
additional flow capacity is required use an acetylene cylinder pack or
manifold system of sufficient size to supply the necessary volume.
CIGWELD supplies both temporary and permanent gas manifolds for
installation. Contact your Thermadyne Area Manager or gas supplier
for further information.
Part No. 307121
Specifications
Part
No.
Model
No.
Tip
size
Operating
Gas
pressure consumption
(kPa)
(l/min)
Oxy Acet Oxy
Acet
306068 10x12HT 10x12 350 100
Part No. 307122
307007 8x12HT
23
22
8x12
150 100 45-58 41-55
150
307121
SHA1
8x12
307122
SHA2
12x12 200 100
100 45-58
74
Heat Mixer
output
Extension
barrel
MJ/hr
75
-
-
180
304002
-
41-55
180
304003 307123/4/5
65
215
304003 307123/4/5
Connect part number 306068 directly into the COMET 3 Cutting Attachment, 304005
Part No. 306068
15
Welding & Heating Tips
COMET Superheating Tips - Oxy/LP Gas
Features and Benefits
Specifications
Provides efficient, economical high intensity heat.
Part
No.
Model
No.
Tip
size
Operating
Gas
Heat Mixer
pressure consumption output
(kPa)
(l/min)
Oxy LP gas Oxy LP gas MJ/hr
306034 20x9HT
20x9
500
100
48
12
40
Heavy copper head for heat and wear resistance.
307120 SHP1
18x12 500
100
200
50
280
304003 307123/4/5
Simple design for ease of cleaning.
307119
36x12
600
100
300
75
420
304003 307123/4/5
307118 SHP3
48x12 600
100
400
100
560
304166 307123/4/5
307117 SHP4*
48x15 1000
300
600
150
840
304166 307123/4/5
Excellent flame stability.
Limited upper edge melt.
Castellations on SHP range as an extra resistance
to backfire.
Spanner adjustment flats milled into tip.
SHP2
SHP tip.
Part No. 307120
Part No. 307119
Part No. 307118
16
-
*NB: When used with 10mm tubing, higher flows and heat output may be obtained (over 1056MJ)
Connect part number 306034 directly to COMET 3 Cutting Attachment, 304005.
Gas pressure & identification stamped on every
Part No. 307117
-
Extension
barrel
Part No. 306034
Accessories
COMET Superheating Barrels
Tubular stainless steel construction gives excellent
strength and heat conductivity. Screw fittings ensure an
Ordering Information
easy leak-free connection between mixer and
Part No.
Description
superheating tip.
307123
Straight stainless steel barrel 735mm long
307125
Gooseneck stainless steel barrel 700mm long
307124
Gooseneck stainless steel barrel 450mm long
Part No. 30124
Part No. 30125
Part No. 30123
17
Notes
18
We’ve got Cutting
& Welding Covered.
Choose CIGWELD endorsed products for premium quality and reliability.
Gas Equipment & Accessories
Welding Machines
Portable Welding
Inverters
Three Phase and
Synergic Pulse
Portable Welding
Inverters
Engine Driven
Welding Equipment
Comet Gas Outfits
and Regulators
Blowpipes, Cutters
and Consumables
Comet Gas Equipment
Accessories
Transmig 3 Phase
& Synergic Pulse
POCKET GUIDE
Get Mobile with our
latest iPhone Pocket
Guide, scan the QR
code for details
Safety, MIG Gun & Accessories
Plasma Cutting Equipment
Welding Consumables
Solid & Flux Cored
Welding Wires
Electrodes, Rods
& Fluxes
Hardfacing
Electrodes and Wires
Plasma Cutting
Equipment
Safety Products
Available for:
Welding Torches,
Consumables and
Accessories
ANDROID
APPLE
1300 654 674
I
www.cigweld.com.au
Authorised Distributor:
AD3931 COMET GEQBCC 9.10
Australia - (Asia Pacific Head Office)
CIGWELD Pty Ltd
A Victor Technologies Company
71 Gower Street, Preston VIC 3072 Australia
Customer Care
Tel: 1300 654 674
Fax: +61 3 9474 7391
Email: [email protected]
International Enquiries:
Tel: +61 3 9474 7508 Fax: +61 3 9474 7488
www.cigweld.com.au
Malaysia Victor Technologies
Lot 151, Jalan Industri 3/5A
Rawang Integrated Industrial Park,
Jln Batu Arang
48000 Rawang Selangor Darul Ehsan
West Malaysia
Indonesia Victor Technologies
JL Angsana II Blok AE No.28
Delta Silicon - Cikarang
Bekasi, 17550
Indonesia
China Victor Technologies
Unit 4F2, Zhao Feng Universal Building
No. 1800 West Zhongshan Road,
Xuhui District, Shanghai 200235
China
Tel: + 60 3 6092 2988 Fax: +60 3 6092 1085
www.victortechnologies.asia
Tel: +62 21 8990 6095 Fax: +62 21 8990 6096
www.victortechnologies.asia
Tel: +86 21 6407 2626 Fax: +86 21 6448 3032
www.victortechnologies.asia
In the interest of continuous improvement, CIGWELD Pty Ltd ABN 56 007 226 815 (Victor Technologies International) reserves the right to change the specifications or design on any of its products without prior notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement