Samsung Samsung-T Protocol User manual

High Resolution 37X Zoom
Color Camera
User Manual
SCZ-3370
B
T
■
■
High Resolution 37X Zoom Color Camera
User Manual
Copyright
©2010 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document
shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the
user’s own responsibility. Samsung Techwin shall have the right to change the contents of this manual without
prior notice for the purpose of enhanced performance.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve
the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Deteriorated performance or natural worn-out in process of time
Before operating the camera, confirm the camera model and correct input power voltage.
To help you understand this manual thoroughly, we’ll introduce our model description.
■ SCZ-3370 SERIES
• NTSC MODEL
SCZ-3370N
SCZ-3370ND
• PAL MODEL
SCZ-3370P
SCZ-3370PD
■ MODEL DESCRIPTION
• SCZ-3370X_ _X
POWER SOURCE
SIGNAL SYSTEM
• SIGNAL SYSTEM
N → NTSC MODEL
P → PAL MODEL
safety information
6
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
7
8
9
This symbol indicates that dangerous voltage consisting a risk of electric
shock is present within this unit.
This exclamation point symbol is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
1
C
WARNING
• To prevent damage which may result in fire or electric shock hazard, do not expose this
appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance
with the installation instructions.
1
2
3
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
4
5
6
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause
abnormal heat generation or fire.
7
4. Securely plug the power cord into the power receptacle. insecure connection may cause
fire.
8
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause
personal injury.
9
1
4_ safety information
e
s
7. Do not install the unit in humid, dusty, or sooty locations. doing so may cause fire or
electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. in such case,
immediately disconnect the power source and contact the service center. continued use
in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. never
disassemble or modify this product in any way. (samsung is not liable for problems
caused by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. doing so may
cause fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong shock to it. Keep away from a
location subject to excessive vibrationor magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature
(below -50°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and
then move or reinstall it.
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do
so may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
e
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this
may damage the CCD image sensor.
e
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any
time.
10. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CCD.
English_5
● SAFETY INFORMATION
c
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers
filled with water on top of the camera. doing so may cause personal injury due to fire,
electric shock, or falling objects.
safety information
im
FCC STATEMENT
1
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions :
2
3
4
5
6
7
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause
undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
8
9
1
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian
Interference.-Causing Equipment Regulations of ICES-003.
1
1
1
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of
their working life. To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate these items from other types of waste and recycle them responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health
or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of
waste and recycle them through your local, free battery return system.
6_ safety information
1
g
e
important safety instructions
1. Read these instructions.
nt
h
Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the
apparatus
Samsung Techwin cares for the environment at all product
manufacturing stages to preserve the environment, and is taking a
number of steps to provide customers with more environment-friendly
products.The Eco mark represents Samsung Techwin’s will to create
environment-friendly products, and indicates that the product satisfies
the EU RoHS Directive.
English_7
● SAFETY INFORMATION
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong is provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving
the cart/ apparatus combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as powersupply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
2.
3.
4.
5.
6.
7.
contents
i
INTRODUCTION
9
9
10
11
Features
What’s included
Component names and
functions
13
13
14
Connecting to Monitor
Connecting to Power
Connecting to 8P Control
Terminal
F
y
y
CONNECTION
13
CAMERA OPERATION
16
TROUBLESHOOTING
y
y
16
17
Menu Configuration
Menu Setup
y
y
38
Troubleshooting
y
38
y
SPECIFICATIONS
39
SAMSUNG-T PROTOCOL
COMMAND DESCRIPTION
44
8_ 목차
39
41
42
Specifications
Dimensions
Dimensions
y
44
SAMSUNG-T Protocol
Command Description
y
y
introduction
FEATURES
y 37x Optical Zoom
The built-in SCZ-3370 optical zoom lens is a highly durable component. It features auto
focus, auto iris, and zoom functions.
y DIS (Digital Image Stabilizer)
Digital image stabilization compensates camera shakings for enhanced image capture.
y SSNR 3 (Samsung Super Noise Reduction)
The high-performance SV-V DSP chip effectively removes low-light gain noise and
ghosting to provide clear images even in dark environments.
y Miscellaneous Functions
SYNC, SENS-UP, FLIP(H/V-REV), D-ZOOM and PRIVACY functions are provided.
y DAY&NIGHT(ICR)
This camera has a function that automatically selects the mode that is appropriate for
daytime or night-time conditions.The COLOR mode operates in daytime conditions to
provide optimum colors, and BW mode operates in night-time conditions to enhance the
definition of the image.
y INTELLIGENCE
Once motion is detected, the camera sends an alert signal to the processing unit,
which, if used in conjunction with an optional alarm, can provide effective surveillance of
your property.
y SSDR (Samsung Super Dynamic Range)
For images with high contrast between bright and dark areas from difficult lighting
conditions such as backlighting, this camera selectively illuminates darker areas while
retaining the same light level for brighter areas to even out the overall brightness.
y Wide Dynamic Range (WDR)
By adopting SV-V DSP chip, the camera delivers clear, high quality pictures even in
backlight, by increasing exposure in dark areas while decreasing it in bright areas.
y VPS (Virtual Progressive Scan)
Virtual Progressive Scan provides a clearer view of objects, which is used for high-quality
video. It is suitable for high-quality recording and Internet transfer.
y PIP (Picture In Picture)
PIP enables you to display the main image along with a collapsed version of the main image.
English_9
● INTRODUCTION
y High Resolution
Adopting high-resolution CCD of 410k (NTSC) / 470k (PAL) pixels provides clear and
sharp image.
introduction
C
WHAT’S INCLUDED
High Resolution 37X Zoom
Color Camera
User Manual
SCZ-3370
High Resolution 37X Zoom
Color Camera
Quick Set-up Guide
SCZ-3370
TD[
Main Body
Instruction Manual
8-PIN CABLE ASSY
FRONT COVERING
Quick Set-up Guide
Ú Install the Front Cover Ring onto the camera before using it with the camera housing.
10_ introduction
COMPONENT NAMES AND FUNCTIONS
TOP
BOTTOM
➋
z|w
lyG}
pzpv
u
TD[
➊ Holder Hole: :
If you want to mount the holder in the top of the camera, loosen the factory-default
screw on the bottom of the holder before proceeding.
➋ Bracket Hole :
Use this if you want to attach the camera to the bracket.
Screws available for this hole should meet the following
specifications.
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
 Attach the bracket to the top of the camera. Use
7*4*0/
screws included in the package or their equivalent
(less than 6mm). Otherwise, the bracket may not
assemble to the camera properly.
461&3
I
L
English_11
● INTRODUCTION
➊
c
introduction
C
BOTTOM VIEW
C
➎
➌
➏
➍
➐
➑
➌ Key Buttons
Following buttons control zoom, focus, and auto focus functions.
y SET (AF): Press and hold this for two seconds to display the menu. Use this if you
change the value of a selected item or change the mode and want to confirm
your change. Press and release this to perform the auto focus.
y Up (TELE) / Down (WIDE): Use this if you want to move a menu item to a desired position
or adjust the zoom factor.
y Left (F-NEAR) / Right (F-NEAR): Use this if you want to change the value of a selected
item or adjust the focus.
➍ Power Input Terminal
Power supply terminal (DC Type : DC12V±10% DUAL Type : DC12±10%/AC24V±10%
➎ Power LED
Illuminates when power is supplied.
➏ Video Output Jack
Used to connect an external video monitor in jack.
➐ GND
Earth-grounding terminal for external devices.
➑ RJ-45 JACK
Terminals, such as RS-485 communications, MD OUT, ZOOM, and FOCUS,
EX_DN are included.
12_ introduction
y
y
C
CONNECTING TO MONITOR
Connect Video Out Jack to the monitor's Video In jack as shown below.
CCD Camera
● CONNECTION
n
connection
Monitor
y Connection methods may vary depending on the video equipment. Please refer
to the model specific instruction manual.
y Connect cables with the unit powered down.
CONNECTING TO POWER
DC Type : DC 12V, 500mA
I
DUAL Type : DC 12V, 500mA / AC24V, 500mA
 Connect the power once the installation is complete.
 The wire is polarized. Match ‘+’ and ‘-’ terminals properly.
English_13
connection
CONNECTING TO 8P CONTROL TERMINAL
C
The camera can be controlled by using external controllers like a Remote
controller. (RS-485 Communication)
MENU
SEARCH
MULTI
REC
MENU
PRESET
CAM
1
6
MON
2
7
GROUP
PTZ
3
8
DVR
4
9
MTX
5
SETUP
ESC
TRACK
FUNC
ENTER
CLOSE
OPEN
0
NEAR
WIDE
FAR
TELE
SPC-6000
8-Pin CABLE ASSY
SPC-200
* 8P
Control Terminal
Name
Cable color Configuration
Description
Name
Cable color
ZOOM
ORANGE
GND
BLUE
-
FOCUS
WHITE/ORANGE
EX DN
WHITE/BLUE
External D/N
COM
GREEN
485+
BROWN
RS-485 communication
ALARM
OUT
WHITE/GREEN
485-
WHITE/BROWN
RS-485 communication
-
Description
*
14_ connection
Connector
Function
Signal Level
I/O
+6V ~ +12V
Tele
COM
ZOOM
I
-6V ~ -12V
+6V ~ +12V
Far
COM
FOCUS
Near
-6V ~ -12V
COM
-
COM
ALARM OUT
5±0.5sec
0V
← →
O
USER Vcc (3V~5V)
DAY mode : D&N terminals must be OPEN to external signals.
(Do not input voltage)
NIGHT mode : D&N terminal must be connected to the ground
EX DN
I
I
COM
I
 Do not simultaneously connect the RS-485 (+) (-) communication line when you
use voltage control ZOOM and FOCUS, using the RECEIVER BOX (SRX-100B).
 ALARM Output format is open collector.
* Match the communication setup between devices when you use the wired
controller (SPC-200) or SPC-6000.
ITEM
MODE
Data Bit
Bit/Sec
Parity
CAM ID NO.
RETURN PACKET
SPC-200
Serial
8 bit
9600bps
EVEN
0
ENABLE
SPC-6000(Factory Default)
Serial
8 bit
9600bps
NONE
1~255
See the SPC-6000 manual
English_15
● CONNECTION
COM
Wide
RN
camera operation
MENU CONFIGURATION
M
U
MAIN SETUP MENU
SSDR
úON
úOFF
WHITE BAL
úATW
úOUTDOOR
úMANUAL
úINDOOR
úAWC→SET
BACKLIGHT
úOFF
úWDR
úBLC
úHLC
INTELLIGENCE
úOFF
úON
FOCUS
úMODE
ú D-ZOOM
úLENS INIT
úZOOM TRACK úZOOM SPEED
úZOOM POS INITúUSER PRESET
úRETURN
EXPOSURE
úBRIGHTNESS
úAGC
úRETURN
úIRIS
úSSNR3
úSHUTTER
úSENS-UP
SPECIAL
úVPS
úDIS
úIMAGE ADJ
úPRIVACY
úSYNC
úDISPLAY
úDAY/NIGHT
úCOMM ADJ
úRETURN
1
RESET
EXIT
2
3
4
16_ camera operation
MENU SETUP
Use the five buttons on back of the camera.
● CAMERA OPERATION
UP button
SET/AF button
LEFT button
DOWN button
RIGHT button
1. Press the SET button for 2 seconds. (Short-pressing the button activates the AUTO FOCUS).
• Main setup menu is displayed on the monitor screen.
MAIN SETUP
Select feature
using the UP or
DOWN button
䯝 SSDR
WHITE BAL
BACKLIGHT
INTELLIGENCE
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
ON
ATW
OFF
OFF
Change the status
using the LEFT or
RIGHT button.
2. Select the desired feature using the UP or DOWN button.
3. Change the status of the selected feature using the LEFT or RIGHT button.
4. When completed, move the arrow indicator to 'EXIT' and press the SET button.
I
 Features marked with a have an accessible submenu.
 An item with the - - - icon is unavailable due to function settings.
English_17
camera operation
SSDR (SAMSUNG SUPER DYNAMIC RANGE)
SSDR illuminates darker spots of an image while retaining the same light level
for brighter spots to even out the overall brightness of images with high contrast
between bright and dark spots
MAIN SETUP
䯝 SSDR
WHITE BAL
ON
ATW
1. When the SETUP menu screen is displayed, select ‘SSDR’ by using the
button so that the arrow indicates ‘SSDR’.
2. Use the button to change the SSDR level according to the contrast between
bright and dark areas.
SSDR OFF
SSDR ON
WHITE BAL (WHITE BALANCE)
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ‘White Bal’ by using the
Up and Down buttons so that the arrow indicates ‘White Bal’ .
2. Select a desired mode using the Up and Down buttons.
MAIN SETUP
SSDR
䯝 WHITE BAL
BACKLIGHT
18_ camera operation
ON
ATW
OFF
⼿#Select one of the following 5 modes, as appropriate for your purpose.
y ATW : Select this when the color temperature is between 1,700˚K and
11,000˚K.
WB MANUAL
▶ RED
BLUE
RETURN
IIIIIIÂIIIIIIIIIIIIIIII
IIIIIIÂIIIIIIIIIIIIIIII
114
93
y AWC⽍SET : To find the optimal luminance level for the current environment,
point the camera towards a sheet of white paper and press the
Function Setup switch. If the environment changes, readjust it.
y OUTDOOR : Select this when the color temperature is between 1,700˚K and
11,000˚K. (sodium light inclusion)
y INDOOR : Select this when the color temperature is between 4,500˚K and
8,500˚K.
I
 White Balance may not work properly under the following conditions. In
this case select the AWC mode.
➊ When the color temperature of the environment surrounding the subject
is out of the control range (e.g. clear sky or sunset).
➋ When the ambient illumination of the subject is dim.
➌ If the camera is directed towards a fluorescent light or is installed in a
place where illumination changes dramatically, the White Balance
operation may become unstable.
BACKLIGHT
Designed to provide clear separation of the subject from the background even under
a severe backlight condition.
1. When the SETUP menu screen is displayed, select ‘Backlight’ by using the
Up and Down buttons so that the arrow indicates ‘Backlight’ .
MAIN SETUP
SSDR
WHITE BAL
䯝 BACKLIGHT
INTELLIGENCE
ON
ATW
OFF
OFF
English_19
● CAMERA OPERATION
y MANUAL :
Select this to fine-tune White Balance
manually. Set White Balance first by
using the ATW or AWC mode. After
that switch to MANUAL mode, fine-tune
the White Balance and then press the
Function Setup switch.
camera operation
2. Select a desired mode using the left or right button according to your needs.
y WDR (Wide Dynamic Range) :
It displays a sharp image of the objects in a scene where both bright and dark
areas exist.
WDR
OFF
- LIMIT : Select a sensitivity level of WDR.
WDR SETUP
(LOW/MEDIUM/HIGH)
▶ LIMIT
MIDDLE
- LEVEL: Select a brightness level of WDR.
IIIIIIIIIIIIIIIIIIIÂIIIII 5
LEVEL
(1~10)
MODE
INDOOR
- MODE : Select a mode that is suitable
ANTI ROLLING
OFF
to the indoor or outdoor backlight
RETURN
condition.
- ANTI ROLLING :
Reduces the difference of ambient colors to lessen the rolling that occurs
under the fluorescent lighting.
y BLC :
You can specify a desired area on the
video manually and set the area to be
displayed more clearly.
- LEVEL : You can adjust the
brightness of the monitoring
area.
- UP/DOWN/LEFT/RIGHT :
You can adjust the position of the
monitoring area.
▶ LEVEL
TOP
BOTTOM
LEFT
RIGHT
RETURN
y HLC (HIGH LIGHT COMPENSATION) :
When a strong light such as streetlamp or
headlight faces forward to the camera, you
can mask that exposed area in order to
protect it from being saturated.
- LEVEL: You can adjust the brightness
of the monitoring area.
- LIMIT : You can specify the operating
conditions for enabling HLC.
▶ LEVEL
MIDDLE
LIMIT
NIGHT ONLY
MASK COLOR
BLACK
MASK TONE IIIIIIÂIIIIIIIIIIIIIIIIII 5
ÂIIIIIIIIIIIIIIIIIIIIIIII 10
TOP
BOTTOM IIIIIIIIIIIIIIIIIIIIIIIIÂ 120
ÂIIIIIIIIIIIIIIIIIIIIIIII 10
LEFT
IIIIIIIIIIIIIIIIIIIIIIIIÂ 160
RIGHT
RETURN
20_ camera operation
BLC SETUP
MIDDLE
25
90
IIIIIIÂIIIIIIIIIIIIIIIIII
55
IIIIIIIIIIIIIIIIÂIIIIIIII 120
IIIIIIÂIIIIIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIIIIÂIIIII
HLC SETUP
- MASK COLOR/TONE :
You can specify the color and brightness of the masking area.
(Black, red, blue, sky blue, pink)
- UP/DOWN/LEFT/RIGHT :
You can adjust the position of the monitoring area.
y OFF : Cancels the BLC function.
 The WDR mode will be disabled if you select MANUAL or A.FLK mode from the shutter menu.
 If you still choose to use WDR, you may encounter one of the following problems that differ depending on
 As the performance of the WDR function may differ depending on the bright-area size of the image, it is
recommended to optimize the installation angle for the best performance.
 When dark, the HLC is only activated when a bright light exceeding a specific size. (In NIGHT ONLY mode.)
 Increasing the maximum value may cause an unnatural portion of the image.
 If you use the VPS (Virtual Progressive Scan) function, the CCD reads differently so you can not use WDR
simultaneously. If you set VPS to ON, WDR will be automatically set to FIXED Mode.
 The use of a DC lens than the manual lens is recommended to WDR optimal performance.
 Activating BLC may cause the camera to repeat the Auto Focus operation depending on lighting
conditions. It is recommended that you use the Focus Setup menu in One-Push or Manual mode.
 Smart Zoom and BLC cannot be used in conjunction with each other:
 Setting up Smart Zoom and then BLC automatically cancels Smart Zoom.
INTELLIGENCE
Enables you to detect and trace a moving object.
MAIN SETUP
SSDR
WHITE BAL
BACKLIGHT
䯝 INTELLIGENCE
FOCUS
EXPOSURE
y MOTION :
Select a type that you want to detect.
- OFF : Do not detect any motion.
- DETECTION: This product enables
you to detect a moving object,
ensuring a better monitoring.
ON
ATW
OFF
OFF
INTELLIGENCE
䯝 MOTION
DETECT BOX
ALARM OUT
SMART ZOOM
DETECT AREA
MASK AREA
SENSITIVITY
DET. SIZE
RETURN
DETECTION
ON
ON
OFF
IIIIIIIIIIIIÂIIIIIIIIII
IIIIIIIIIIIIÂIIIIIIIIII
3
3
English_21
● CAMERA OPERATION
the lightning condition.
➊ Unnatural change of colors that cause an unnatural image on the screen
➋ Noise on the bright area of the image
camera operation
- TRACKING : Detect and trace a moving object.
TRACKING
y MODE : Specify the use of the fences
▶ MODE
OFF
that you have selected in the
TYPE
LINE
FENCE SEL menu.
COUNT
OFF
FILL
OFF
y TYPE : You can select one of two types
POSITION
for the fence LINE and AREA
RETURN
y COUNT: Display the number of times
that an object enters or exits
from the fence.
y FILL: Specify the use of color filling on the selected fence.
y POSITION: Specify the position and detectable direction of the line fence or
area fence, depending on the fence type.
1) LINE FENCE
LINE FENCE
▶ SEL POS: Select a changing
▶ SEL POS
POS1
point from position 1
IIIIIÂIIIIIIIIIIIIIIII 25
X POS
and position 2.
ÂIIIIIIIIIIIIIIIIIIIIII
1
Y POS
▶ X POS/Y POS: Specify the position
DIRECTION
DIR1
of the changing point that you have
RETURN
selected in the SEL POS menu.
▶DIRECTION
x DIR 1: Detect an object that moves from left to right based on the
specified fence line.
x DIR 2: Detect an object that moves from right to left based on the
specified fence line.
x DIR 1/2: Detect an object that moves in any direction of right to left or left
to right based on the specified fence line.
▶RETURN: Save the fence position settings and return to the
INTELLIGENCE menu.
2) AREA FENCE
▶ SEL POS:
Select a changing point from
position 1 through position 4.
▶ X POS/Y POS:
Specify the position of the
changing point that you have
selected in the SEL POS menu.
22_ camera operation
AREA FENCE
▶ SEL POS
POS1
IIIIIÂIIIIIIIIIIIIIIII 20
X POS
IIIIIÂIIIIIIIIIIIIIIII 20
Y POS
DIRECTION
IN
RETURN
x IN: Detect any object that enters the specified fence area.
x OUT: Detect any object that exits from the specified fence area.
x IN/OUT: Detect any object that enters or exits from the specified fence
area.
▶ RETURN: Save the fence position settings and return to the
INTELLIGENCE menu.
- FIXED/MOVED: Detect if an existing object (on the screen) disappears or if an object
appears from nowhere and stays for a certain time.
 In following situations, FIXED/MOVED detection may not work properly.
y If multiple motions continue at random.
y If a fixed object continues to move in the same position.
y If a newly appearing object conceals another object that is moving.
y DETECT BOX: Display an object in a box that is detected to move in your specified type.
y ALARM OUT: Output the detection signal through the rear port of the camera if an
object is detected to move in your specified type.
y SMART ZOOM :
Smart zoom is operated in connection with
SMART ZOOM SETUP
MOTION DETECTION. When the SMART
▶ START ZOOM
X1
ZOOM function is ‘ON’ while the MOTION
TARGET ZOOM
X5
DWELL TIME
5 SEC
DETECTION mode is ‘ON’, the zoom goes
RETURN
to the TARGET ZOOM position once motion
is detected. Once the zoom action is finished
and ‘DWELL TIME’ has passed, the zoom returns to the ‘START ZOOM’ position.
- START ZOOM : By moving the left or right button in the ‘START ZOOM’ item
to select the zoom position from 1x to 37x to be returned
after the ‘SMART ZOOM’ action is over.
- TARGET ZOOM : Use the left or right button in the ‘TARGET ZOOM’ item to
select the zoom position from 1x to 37x to be used during
MOTION DETECTION.
- DWELL TIME : Use the left or right button in the ‘DWELL TIME’ item to
select a time between 5 and 60 seconds for the dwell time
before the zoom is returned to the ‘START ZOOM’ position.
(5,7,10,15,20,30,40,60 sec)
English_23
● CAMERA OPERATION
ft
▶ DIRECTION
camera operation
y DETECT AREA : You can specify a motion
detection area.
y MASK AREA :
You can specify an exceptional area to
motion detection by masking the area.
- AREA SEL: Select a desired one from
4 areas.
- AREA: Specify the use of the selected
area.
- Up/Down/Left/Right:
You can adjust the position of the
exceptional area to motion detection.
DETECT AREA
▶ TOP
BOTTOM
LEFT
RIGHT
RETURN
ÂIIIIIIIIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIIIIIIÂ
ÂIIIIIIIIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIIIIIIÂ
1
50
1
50
MASK AREA
▶ AREA
MODE
TOP
BOTTOM
LEFT
RIGHT
RETURN
AREA1
OFF
30
110
25
IIIIIIIIIÂIIIIIIIIIIII 110
IIIIÂIIIIIIIIIIIIIIIII
IIIIIIIIIIÂIIIIIIIIIII
ÂIIIIIIIIIIIIIIIIIIIII
y SENSITIVITY : Specify the sensitivity level of the motion detection.
The lower the level is, the stronger the sensitivity becomes.
y DETECT SIZE : Specify the size of an object to detect on the screen.
The higher the level is, the greater the size becomes.
y RETURN : Save the INTELLIGENCE settings and return to the SPECIAL SETUP menu.
24_ camera operation
FOCUS
From the Main Setup menu, select FOCUS and press SET. You can now change
the focus.
y MODE : You can select the most
suitable zoom mode. Move
the arrow indicator to ’
MODE‘ using UP or DOWN
button.
ON
ATW
OFF
OFF
FOCUS SETUP
䯝 MODE
ZOOM TRACK
ZOOM SPEED
D-ZOOM
ZOOM POS INIT
USER PRESET
LENS INIT
RETURN
AUTO
AUTO TRACK
FAST
OFF
OFF
OFF
MANUAL
- AUTO :
• The focus will be adjusted automatically according to the zoom factor.
• Select the AF (AUTO FOCUS) mode
and press SET. Use the Up/Down
button to perform the zooming.
ZOOM/FOCUS POS SETUP
↑ : TELE ↓ : WIDE
- ONE-PUSH :
• After the zooming, the focus will be
automatically adjusted once.
• Select the ONE PUSH mode and use
the Up/Down button to perform the
zooming. Use the Left/Right button to
adjust the focus.
ZOOM/FOCUS POS SETUP
↑ : TELE ↓ : WIDE
← : NEAR → : FAR
English_25
● CAMERA OPERATION
MAIN SETUP
SSDR
WHITE BAL
BACKLIGHT
INTELLIGENCE
䯝 FOCUS
EXPOSURE
camera operation
- MANUAL :
• The focus should be adjusted manually,
depending on the zoom factor.
• Select the MF (MANUAL FOCUS) mode
and use the Up/Down button to perform the
zooming. Use the Left/Right button to adjust
the focus.
ZOOM/FOCUS POS SETUP
↑ : TELE ↓ : WIDE
← : NEAR → : FAR
y ZOOM TRACK :
Select ‘ON’ for the ‘SMART ZOOM’ item
FOCUS SETUP
in the MOTION DETECTION menu and
MODE
AUTO
press SET button to change the settings
䯝 ZOOM TRACK
AUTO TRACK
for the ‘SMART ZOOM’ function.
ZOOM
SPEED
FAST
Use the left or right button in the
‘ZOOM’ item to select ‘AUTOTRACK’ or
‘TRACK’ and press SET button to activate the zoom action focus function.
- AUTO TRACK : Zooming in while deciding or adjusting the status of the focus.
- TRACK : The camera moves the focus track which is established.
- OFF : Only the zoom lens moves.
y ZOOM SPEED :
Configure zoom tracing speed using this
feature. Position the indicator over 'ZOOM
SPEED' using the UP or DOWN button
and then set to desired mode using the
LEFT or RIGHT button.
y D-ZOOM :
Configure magnification limit from x2~x16
using this feature. Position the indicator
over 'D-ZOOM' using the UP or DOWN
button Set 'D-ZOOM' to 'ON' and press
the SET button to confirm.
FOCUS SETUP
MODE
ZOOM TRACK
䯝 ZOOM SPEED
D-ZOOM
AUTO
AUTO TRACK
FAST
OFF
FOCUS SETUP
MODE
ZOOM TRACK
ZOOM SPEED
䯝 D-ZOOM
ZOOM POS INIT
AUTO
AUTO TRACK
FAST
OFF
OFF
D-ZOOM LIMIT SETUP
䯝 LIMIT
RETURN
I
 When the DIS is enabled, you cannot use the D-ZOOM.
26_ camera operation
X2
y ZOOM POS INIT :
Moves to the controlled ZOOM position
when the power is truned on and the initial
ZOOM position has been set.
FOCUS SETUP
AUTO
AUTO TRACK
FAST
OFF
OFF
OFF
- AUTO : If you turn the power off and on, the zoom magnification level is set to
the previous level that was set before the power went off.
- MANUAL : The zoom magnification level can be set from 1x to 37X.
I
 The zoom postion is saved after 5 seconds when you set zoom function.
y USER PRESET :
Preset user-designated configurations
FOCUS SETUP
using this feature. Position the indicator
MODE
AUTO
over ‘USER PRESET’ using the UP or
ZOOM TRACK
AUTO TRACK
DOWN button and then set to ‘ON’ using
ZOOM
SPEED
FAST
the LEFT or RIGHT button. Press the SET
D-ZOOM
OFF
button to confirm.
ZOOM POS INIT
OFF
- PRESET NO :
䯝 USER PRESET
OFF
Up to 128 preset configuratons are
LENS INIT
MANUAL
supported.
- SAVE : Save configured preset.
- CLEAR : Clear configured preset.
- RETURN : Revert to the FOCUS SETUP menu.
y LENS INIT :
Use the left or right button in the ‘Lens
initialization’ item select ‘Automatic’ or
‘Manual’ and then press the SET button.
- AUTO : The lens can automatically be
set by a pre-selected day, from
1-day to 7-days. This will start
from when the time is set.
- Manual : The Lens will reset when you
press the SET button.
FOCUS SETUP
MODE
ZOOM TRACK
ZOOM SPEED
D-ZOOM
ZOOM POS INIT
USER PRESET
䯝 LENS INIT
RETURN
AUTO
AUTO TRACK
FAST
OFF
OFF
OFF
MANUAL
y RETURN : Save the current settings and return to the parent menu (MAIN SETUP).
English_27
● CAMERA OPERATION
MODE
ZOOM TRACK
ZOOM SPEED
D-ZOOM
䯝 ZOOM POS INIT
USER PRESET
EXPOSURE
From the Main Setup menu, select EXPOSURE and press SET. You can now
change the exposure setting.
MAIN SETUP
SSDR
WHITE BAL
BACKLIGHT
INTELLIGENCE
FOCUS
䯝 EXPOSURE
SPECIAL
y BRIGHTNESS :
Use this feature to adjust image brightness.
Position the indicator over 'BRIGHTNESS'
using the UP or DOWN button. Then
increase or decrease brightness level using
the LEFT or RIGHT button while verifying
the changes on screen. Set END once
desired level is obtained.
y IRIS : Set 'IRIS' to 'AUTO' or 'MANUAL'.
Position the indicator over 'IRIS'
using the UP or DOWN button and
then select the desired iris mode
using the LEFT or RIGHT button.
- AUTO: The iris is automatically
activated upon illumination.
ON
ATW
OFF
OFF
EXPOSURE SETUP
▶ BRIGHTNESS
IRIS
50
AUTO
IIIIIIIIIIIIIIIIIIÂIIII
EXPOSURE SETUP
BRIGHTNESS
▶ IRIS
SHUTTER
50
AUTO
---
IIIIIIIIIIIIIIIIIIÂIIII
IRIS MANUAL SETUP
▶ IRIS F-No
RETURN
F1.6
- MANUAL : Manual iris configuration.
Set 'IRIS' to 'MANUAL'
using the LEFT or RIGHT
button and then press the
SET button. Increase or decrease iris level using the LEFT or RIGHT
button while verifying the changes on screen.
X2
28_ camera operation
- A.FLK (NTSC: 1/100, PAL: 1/120) : Flicker-free mode.
- ESC : Automatic shutter speed setting (optimal).
Auto operation is possible only when the IRIS is set to MANUAL.
- MANUAL : Manual shutter speed setting.
y In MANUAL mode, the optimal shutter
speed needs to be designated. Select
from 1/60 to 1/120,000 (NTSC) or
from 1/50 to 1/120,000 (PAL). *
'Sens-Up' mode can be configured
manually (2x to 512x).
I
SHUTTER MANUAL SETUP
▶ SHUTTER VAL
RETURN
1/50
 If facing the camera directly to fluorescent lighting with the shutter mode set to ESC, you may
encounter corrupt pixels. To prevent this, switch the iris mode to Auto or fix the shutter speed
to 1/60, or adjust the recording position as appropriate.
y AGC (Auto Gain Control) :
Select GAIN and use the Left/Right button to switch the mode to: OFF, LOW,
MEDIUM, HIGH OR MANUAL.
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
▶ AGC
SSNR3
50
AUTO
--HIGH
MEDIUM
IIIIIIIIIIIIIIIIIIÂIIII
GAIN MANUAL SETUP
▶ AGC VAL
RETURN
5dB
T
English_29
● CAMERA OPERATION
y SHUTTER : Control image brightness by
EXPOSURE SETUP
adjusting shutter speed.
Position the indicator over
BRIGHTNESS IIIIIIIIIIIIIIIIIIÂIIII 50
'SHUTTER' using the UP or
IRIS
AUTO
DOWN button. Then select
▶ SHUTTER
--the desired shutter mode
AGC
HIGH
(A.FLK, ESC, MANUAL)
using the LEFT or RIGHT button.
y SSNR(Samsung Super Noise Reduction) : The background noise in a lowcontrast scene will be reduced variably depending on the mode. The noise will be
reduced in the sequence: OFF, LOW, MEDIUM, HIGH. Select DNR and use the
Left/Right button to switch the mode to: OFF, LOW, MEDIUM or HIGH.
- LOW : Low noise reduction
- MEDIUM : Medium noise reduction
- HIGH: High noise reduction
- OFF : Disabled
I
 Setting 'AGC' to OFF locks 'SSNR3' configuration.
y SENS-UP : This feature ensures clear
images at night or under low
light conditions.
➊ Position the indicator over 'SENS-UP'
SENS-UP LIMIT SETUP
▶ LIMIT
RETURN
X2
using the UP or DOWN button.
➋ Set 'SENS-UP' to the desired mode using the LEFT or RIGHT button.
y AUTO : Select this mode for use in night time or under low light conditions.
y OFF : Disabled
I
 If GAIN of EXPOSURE is not in use, the SENS-UP (Sensitivity-Up) is set to “---“.
 Once 'AUTO' mode is set, the user can configure the SENS-UP limit by increasing/
decreasing the shutter speed (e.g.: X2, X4....... X32, X64, X128, X256, X512).
 Enabling Sens-Up increases camera sensitivity and may result in additional
noise and/or other phenomenons. This is normal.
y RETURN : To revert to the main setup menu.
30_ camera operation
/
MAIN SETUP
SSDR
WHITE BAL
BACKLIGHT
INTELLIGENCE
FOCUS
EXPOSURE
䯝 SPECIAL
RESET
y VPS (Virtual Progressive Scan)
Virtual Progressive Scan provides a
clearer view of objects, which is used for
high-quality video. It is suitable for highquality recording and Internet transfer.
ON
ATW
OFF
OFF
● CAMERA OPERATION
.
SPECIAL
SPECIAL SETUP
䯝 VPS
PRIVACY
DAY/NIGHT
OFF
OFF
AUTO
- OFF : Switch the video recording system
to 2:1 Interlace Scan.
- ON : Switch the video recording system to Virtual Progressive Scan.
y PRIVACY : Hide the area that you want not to be displayed on the screen.
➊ When the SPECIAL menu screen is
displayed, using the UP or DOWN
button so that the arrow indicates
‘PRIVACY’.
➋ Set up the mode using the 4
PRIVACY AREA SETUP
䯝 AREA
AREA 1
MODE
ON
MASK COLOR
GREEN
TRANSPARENCY
OFF
SEL POS
L_TOP
ÂIIIIIIIIIIIIIIIIIIIIII
XPOS
10
ÂIIIIIIIIIIIIIIIIIIIIII
YPOS
10
RETURN
direction buttons.
- AREA : You can specify up to 12
areas to your preference.
- MODE : Determines whether to use
the area selected in the
AREA SEL.
- MASK COLOR : You can select one from 6 colors (green, red, blue, black,
white and gray) that is used to fill the selected area.
- TRANSPARENCY : Specify the use of transparency on the selected area.
- SEL POS/X POS/Y POS : Changes the position of the selected area.
- RETURN : Saves the PRIVACY settings and return to the SPECIAL SETUP menu.
English_31
y DAY/NIGHT : You can display pictures in color or black and white.
➊ When the SETUP menu screen is
displayed, select ‘DAY/NIGHT’ using
the UP or DOWN button so that the
arrow indicates 'DAY/NIGHT'.
➋ Select a desired mode using the LEFT
SPECIAL SETUP
VPS
PRIVACY
䯝 DAY/NIGHT
DIS
SYNC
OFF
OFF
AUTO
OFF
INT
or RIGHT button according to the
picture display you want.
y AUTO : The mode is switched
to 'Color' in a normal
environment, but switches to 'B/W' mode when ambient
illumination is low. To set up the switching time or speed for AUTO
mode, press the SET button.
y COLOR: The picture is always displayed in color.
y B/W : The picture is always displayed in black and white.
- DWELL TIME : You can select day/night switching delay time from.
Ą 5,7,10,15,20,30,40, 60(sec)
- DURATION : You can select the day/night switching point(lux).
Color → B/W
B/W → Color
Fast
2.5Lux
4Lux
Slow
1Lux
6Lux
※ Illumination table if the gain is set to HIGH
y EXT : This mode allows you to apply a desired filter to external signals.
I
 The brightness of illumination is changeable by installed environment.
32_ camera operation
y DIS :The DIS mode can compensate for
vibration of the camera
SPECIAL SETUP
I
OFF
OFF
AUTO
OFF
INT
 When DIS is operating, D-ZOOM does not operate.
y SYNC :Two synchronization modes are available INTERNAL and EXTERNAL LINELOCK. In LINE-LOCK mode, it synchronizes the camera's video out signal to
the external SYNC signal.
y INT : Internal synchronization
y LL : External line-lock synchronization
- If you choose 'LL', you can adjust the desired phase.
Press the SET button.
- You can adjust the desired phase from 0 to 359.
y COMM ADJ (Communication Adjustment) :
This function sets up the camera
communication status when controlling
the camera through an external
controlled device.
➊ When the SPECIAL menu screen is
displayed, using the UP or DOWN
button so that the arrow indicates
‘COMM ADJ’.
COMMUNICATION SETUP
▶ PROTOCOL
CAM ID
BAUD RATE
UART MODE
RET PKT
RETURN
SAMSUNG-T
1
9600
8-N-1
DISABLE
IIIIIIIIIIIIIIIIIIÂIIII
➋ Set up the mode moving the 4 direction of the SET button.
- Protocol : Select the communication PROTOCOL. (SAMSUNG-T/PELCO-D/
PELCO-P/ BOSCH/HONEYWELL/VICON/AD/SAMSUNG-E/
PANASONIC)
- CAM ID : Determines the camera's identification number (between 0 and 255).
- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600/1152000 bps.
English_33
● CAMERA OPERATION
VPS
PRIVACY
DAY/NIGHT
䯝 DIS
SYNC
- UART MODE : You can select NONE, EVEN or ODD for the parity bits.
- RET PKT : You can choose whether to send an ACK signal when the
communication control command is issued to the camera.
y IMAGE ADJ : Includes image quality or special function factors.
➊ When the SETUP menu screen is
displayed, select ‘IMAGE ADJ.’ using
the UP or DOWN button so that the
arrow indicates 'IMAGE ADJ.
➋ Select a desired mode using the LEFT
or RIGHT button.
SPECIAL SETUP
VPS
PRIVACY
DAY/NIGHT
DIS
SYNC
䯝 IMAGE ADJ
DISPLAY
RETURN
OFF
OFF
AUTO
OFF
INT
y PIP (Picture In Picture):
PIP enables you to display the
IMAGE SETUP
main image along with a collapsed
▶ PIP
OFF
version of the main image. The
H-REV
OFF
position of the collapsed image can
V-REV
OFF
be adjusted to your preference.
SHARPNESS
ON
y H-REV : You can flip the picture
MONITOR
LCD
horizontally on the screen.
RETURN
y V-REV : You can flip the picture
vertically on IMAGE ADJen.
y SHARPNESS :
As you increase this value, the picture outline becomes stronger and clearer.
y Monitor : Please change the settings value of video appropriate to your
monitor.
- LCD: Please select this menu item
when using an LCD monitor.
34_ camera operation
LCD MONITOR SETUP
▶ GAMMA
PED LEVEL
COLOR LEVEL
RESET
RETURN
0.55
25
IIIIIIIIIIIIIIIIIIÂIIII
5
IIIIIIIIIIIÂIIIIIIIIIII
- CRT : Please select this menu item
when using a CRT monitor.
USER MONITOR SETUP
▶ GAMMA
PED LEVEL
COLOR LEVEL
RESET
RETURN
IIIIIIIIIIIÂIIIIIIIIIII
IIIIIIIIIIIIIIIIIIÂIIII
0.55
25
5
y RETURN : Return to the SPECIAL menu.
y DISPLAY
y CAM TITLE
The camera title will be displayed on
the monitor if you have provided one.
➊ Press the SET button to display the
main setup menu and move the arrow
indicator to ‘CAM TITLE’ using the UP
or DOWN button.
➋ Set ‘CAM TITLE’ to ‘ON’ using the UP
or DOWN button.
I
 If the CAM TITLE feature is set to
‘OFF’, the name will not displayed
in the monitor
SPECIAL SETUP
VPS
PRIVACY
DAY/NIGHT
DIS
SYNC
IMAGE ADJ
䯝 DISPLAY
RETURN
OFF
OFF
AUTO
OFF
INT
DISPLAY SETUP
▶ CAM TITLE
CAM ID
CAM INFO
ZOOM MAG
FONT COLOR
LANGUAGE
RETURN
OFF
OFF
OFF
OFF
WHITE
ENGLISH
English_35
● CAMERA OPERATION
- USER : Please use this menu item when
using a monitor other than
standard ones. You can change
the gamma, PED level, and
color gain in the sub menus.
CRT MONITOR SETUP
▶ PED LEVEL IIIIIIIIIIIÂIIIIIIIIIII 25
COLOR LEVEL IIIIIIIIIIIIIIIIIIÂIIII 5
RESET
RETURN
➌ Press the SET button.
➍ Use the direction buttons to move to
a desired character and press SET.
Repeat this process to enter up to 15
characters.
I
CAMERA TITLE SETUP
A B C D E F G H I J K L M
NOPQRSTUVWXYZ
a b c d e f g h i j k l m
n o p q r s t u v w x y z
- . 0 1 2 3 4 5 6 7 8 9
←→ CLR POS END
_______________
 Correcting Mistakes
Move the cursor th ‘CLR’ and press the
SET button to clear the entire entry. To
modify one character, use LEFT or
RIGHT to position the cursor above the
character to be modified and click the
SET button after selecting the character
to enter.
FRONT DOOR
➎ Enter a title, move the cursor to ‘POS’ and press the SET button. The
entered title appears on the screen. Select the position to display the title
on the screen by moving the 4 direction buttons and press the SET button.
When the position is determined, select.
y CAM ID : Displays camera ID on top left corner of the screen.
y CAM INFO : Displays camera information on screen.
y ZOOM MAG : Use this feature to display the current zoom magnification level on
screen. Position the indicator over ‘ZOOM MAG’ using the UP or
DOWN button. Then set to ON using the LEFT or RIGHT button.
y FONT COLOR : You can select the font color(white,yellow,green,red,blue)
y LANGUAGE : You can select the menu language according to your
requirements (English, Japanese, Spanish, French, Portuguese,
Taiwanese, Korean, German, Italian, Russian, Polish, Czech,
Romanian, Serbian, Turkish)
y RETURN : Select this to save the SPECIAL menu settings and return to the SPECIAL menu.
36_ camera operation
RESET
To reset your camera to factory default condition.
Communication, Language and Monitor settings are not initialized.
● CAMERA OPERATION
EXIT
To finish setup menu.
n
,
.
English_37
troubleshooting
s
TROUBLESHOOTING
S
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
V
Im
PROBLEM
SOLUTION
T
E
Nothing appears on the
screen.
► Ensure that your camera is supplied with rated
power as appropriate.
► Check that you have properly connected VIDEO
cable to the camera VIDEO output jack.
The image on the screen is
dim.
► If the lens is dusty, wipe it out with a clean cloth or
brush.
► Set the monitor to proper condition.
► If the camera is exposed to too strong light,
change the camera position.
The image on the screen is
dark.
► Adjust the contrast feature of the monitor.
► If you have an intermediate device, set the 75 /
Hi-z properly.
V
The camera is not working
properly, and the surface of
the camera is hot.
► Check that you have properly connected the
camera to an appropriate power source.
M
The SENS-UP function does
not work.
► Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
► Check that SHUTTER of EXPOSURE SETUP menu
is ‘A.FLK’ or ‘MANUAL’.
The Motion Detection function
does not work.
► Check if you have set the Intelligence Video
Analysis mode to ON from the SPECIAL menu.
Color is not correct.
► Check the setting of WHITE BAL SETUP menu .
S
S
F
H
M
S
L
F
A
M
F
Z
O
O
The screen flickers continually. ► Check that direction of camera turns toward the Sun.
When coaxial communication
is not available:
►Make sure that the camera and monitor are
installed within the recommended distance.
►Use the video amplifier equivalent to coaxitron if the
recommended installation distance is exceeded.
If the lens is out of focus
▶ Check if the Zoom/Focus lever of the lens is adjusted
C
D
B
W
38_ troubleshooting
properly to the focus.
C
D
specifications
SPECIFICATIONS
SCZ-3370N
SCZ-3370ND
SCZ-3370P
SCZ-3370PD
VIDEO
Imaging Device
1/4” Exview Double Scan CCD
811(H) x 508(V)
811(H) x 508(V)
795(H) x 596(V)
795(H) x 596(V)
Effective Pixels
768(H) x 494(V)
768(H) x 494(V)
752(H) x 582(V)
752(H) x 582(V)
Scanning System
2 : 1 Interlace, Progrssive
Synchronization
Internal / Line Lock
Internal
Internal / Line Lock
Internal
Frequency
H : 15.734KHz
V : 59.94Hz
H : 15.734KHz /
V : 59.94Hz
H : 15.625KHz /
V : 50Hz
H : 15.625KHz /
V : 50Hz
Horizontal Resolution
Color : 600 TV lines, B/W : 700TV lines
Min. Illumination
Color : 0.7Lux @ F1.6 (50IRE), 0.001 Lux (Sens-up, 512x)
B/W : 0.07 Lux @ F1.6 (50IRE), 0.0001 Lux ( Sens-up, 512x )
S/N (Y Signal)
52dB (AGC off, Weight on)
Video Output
CVBS : 1.0 Vp-p / 75Ω composite
Lens Type
Focal Length (Zoom Ratio)
3.5~129.5mm (Optical 37x)
Max. Aperture Ratio
1:1.72 (Wide) ~ 3.94 (Tele)
Angular Field of View
H : 55.5°(Wide) ~ 1.59°(Tele) / V : 42.5°(Wide) ~ 1.19°(Tele)
Min. Object Distance
1.5m
Focus Control
Auto / Manual / One Push
Zoom Movement Speed
2.8 sec ( Wide to Tele )
OPERATIONAL
On Screen Display
NTSC : Multi-language Support
English, Japanese, Spanish, French, Portuguese, Taiwanese, Korean
PAL : Multi-language Support
English, French, German, Spanish, Italian, Russian, Polish,
Czech, Romanian, Serbian, Turkish, Portuguese
Camera Title
Off / On (Displayed 15 characters)
Day & Night
Auto (ICR) / External / Color / B/W
Backlight Compensation
Off / HLC / BLC / WDR
Wide Dynamic Range
128x
Contrast Enhancement
SSDR ( Off/On )
Digital Noise Reduction
SSNRIII ( Off/ Low / Medium / High )
128x
160x
160x
English_39
● SPECIFICATIONS
Total Pixels
specifications
D
SCZ-3370N
Digital Image Stabilization
SCZ-3370ND
SCZ-3370P
SCZ-3370PD
Off / On
Privacy Masking
Off / On (12 programmable zones)
Sens-up (Frame Integration)
2x ~ 512x
Gain Control
Off / Low / Medium / High / Manual
White Balance
ATW / Outdoor / Indoor / Manual / AWC (1,700K° ~ 11,000K°)
Electronic Shutter Speed
1/60~1/120,000sec
Digital Zoom
Off / On (1x ~ 16x)
1/50~1/120,000sec
Flip / Mirror ( Reverse )
Off / H-Rev / V-Rev / HV-Rev
VPS
Off / On
Intelligent Video Detection
Fixed_Moved, Motion Detection, Tracking, Fence, Counting
Alarm
1 Out
Communication
Coaxial Control ( SPC-300 Compatible ), RS-485
Protocol
Coax : Pelco-C ( Coaxitron )
RS-485: Samsung-T, Samsung-E, Pelco-D, Pelco-P, Panasonic, Bosch, Honeywell,
Vicon, AD
Environmental
Operating Temperature /
-10°C ~ +50°C (+14°F ~ +122°F) / Less than 90% RH
Humidity
Electrical
Input Voltage/Current
Dual ( 24VAC±10% 12VDC±10%
& 12VDC±10% )
Dual ( 24VAC±10% 12VDC±10%
& 12VDC±10% )
Power Consumption
Max. 6.1W
Max. 6.1W
Max. 4.7W
Max. 4.7W
Mechanical
Color / Material
Black, Silver / Aluminium
Dimension (WxHxD)
67.6 x 67.6 x 142.5mm
(2.66”x2.66”x5.61”)
excluding projections
67.6 x 67.6 x 118.5mm 67.6 x 67.6 x 142.5mm 67.6 x 67.6 x 118.5mm
(2.66”x2.66”x4.67”)
(2.66”x2.66”x5.61”)
(2.66”x2.66”x4.67”)
excluding projections
excluding projections
excluding projections
Weight
500g (1.10lb)
410g (0.90lb)
500g (1.10lb)
410g (0.90lb)
ö The specification for this product may change without prior notice for product improvement.
40_ specifications
DIMENSIONS
<SCZ-3370>
● SPECIFICATIONS
Unit : mm (Inches)
67.6 (2.66")
144.6 (5.69")
73.3 (2.89")
142.5 (5.61")
67.6 (2.66")
m
t.
52.5 (2.07")
English_41
specifications
DIMENSIONS
<SCZ-3370D>
Unit : mm (Inches)
67.6 (2.66")
120.7 (4.75")
42 (1.65")
42_ specifications
67.6 (2.66")
73.3 (2.89")
118.5 (4.67")
MEMO
English_43
SAMSUNG-T Protocol Command Description
SAMSUNG-T PROTOCOL COMMAND DESCRIPTION
Command Name
Reset
Byte1
Byte2
Byte3
Command Packet
STX
CAM ID
HOST ADDR
CA
Return Packet
STX
CAM ID
HOST ADDR
RES
Checksum
CHECKSUM CALCULATION : UNARY OPERATION OF
SUMMATION FROM BYTE2 TO BYTE9.
EX) CHECKSUM = ~ (BYTE2+BYTE3+...+BYTE8+BYTE9);
Function
Reset all data to factory default value.
Command Packet
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
Function
Focus Far
A0h
CAM ID
HOST ADDR
0
Return Packet
A0h
CAM ID
HOST ADDR
0
Move focus lens to near direction.
Command Packet
A0h
CAM ID
HOST ADDR
02
Return Packet
A0h
CAM ID
HOST ADDR
02
Function
Zoom Wide
Move focus lens to far direction.
Command Packet
Function
Focus Near
B yte4
Move zoom lens to wide direction.
Command Packet
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
Command Packet
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
Command Packet
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
Function
Zoom Tele
Function
ZOOM Direct
Parameter
P1, P2 : OPTICAL ZOOM = 0000h~064Dh
P3 : DIGITAL ZOOM = ((256*10)/Ratio)-1
EX) D-ZOOM 1.1x : P3=E7h =
((256*10)/11)-1, Ratio 11 me ans 1.1x.
D-ZOOM 2.0x : P3=7Fh =
((256*10)/20)-1, Ratio 20 means 2.0x.
44_ SAMSUNG-T Protocol Command Description
3
Byte 6
Byte7
Byte8
Byte9
Byte10
Byte11
CAMMAND
DATA3
DATA4
DATA5
DATA6
ETX
CHECKSUM
DDR
RESPONSE
DATA3
DATA4
DATA5
DATA6
ETX
CHECKSUM
OF
DDR
000Fh
00h
00h
00h
00h
AFh
CHECK SUM
DDR
000Fh
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0040h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0040h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0020h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0020h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
00FFh
P1
P2
P3
00h
AFh
CHECK SUM
DDR
00FFh
P1
P2
P3
00h
AFh
CHECK SUM
English_45
● SAMSUNG-T PROTOCOL COMMAND DESCRIPTION
B yte4 ll Byte5
DDR
SAMSUNG-T Protocol Command Description
Function
AF Stop
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
Function
One push AF
Stop zoom & focus lens moving.
Command Packet
Unconditionally execute auto focus.
Command Packet
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
Function
Save current user preset configuration information.
Command Packet
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
User Preset Save
Parameter
P1 : 00h(USER PRESET 1) ~ 80h(USER PRES ET 128)
Function
Execute selected user preset.
Command Packet
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
User Preset Exec.
Parameter
P1 : 00h(USER PRESET 1) ~ 80h(USER PRES ET 128)
Function
Clear selected user preset.
Command Packet
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
User Preset Clear
Parameter
P1 : 00h(USER PRESET 1) ~ 80h(USER PRES ET 128)
Function
Display OSD menu on the screen.
Clear OSD menu and save current menu setup.
Command Packet
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
OSD Menu On/Off
OSD Menu Up
Parameter
P1 : 00h = ON
01h = OFF
Function
Move OSD arrow to down.
Command Packet
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
46_ SAMSUNG-T Protocol Command Description
0000h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0000h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0045h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0045h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0003h
P1
00h
00h
00h
Afh
CHECK SUM
DDR
0003h
P1
00h
00h
00h
Afh
CHECK SUM
DDR
0007h
P1
00h
00h
00h
Afh
CHECK SUM
DDR
0007h
P1
00h
00h
00h
Afh
CHECK SUM
DDR
0005h
P1
00h
00h
00h
Afh
CHECK SUM
DDR
0005h
P1
00h
00h
00h
Afh
CHECK SUM
DDR
00B1h
P1
00h
00h
00h
Afh
CHECK SUM
DDR
00B1h
P1
00h
00h
00h
Afh
CHECK SUM
DDR
0008h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0008h
00h
00h
00h
00h
AFh
CHECK SUM
8)
8)
8)
English_47
● SAMSUNG-T PROTOCOL COMMAND DESCRIPTION
DDR
SAMSUNG-T Protocol Command Description
Function
OSD Menu Down
A0h
CAM ID
HOST ADDR
00
Return Packet
A0h
CAM ID
HOST ADDR
00
Function
OSD Menu Left
Command Packet
A0h
CAM ID
HOST ADDR
00
A0h
CAM ID
HOST ADDR
00
Command Packet
A0h
CAM ID
HOST ADDR
00
A0h
CAM ID
HOST ADDR
00
Move to inside menu
Command Packet
A0h
CAM ID
HOST ADDR
0
Return Packet
A0h
CAM ID
HOST ADDR
0
Function
OSD Menu ESC
Move OSD arrow to right.
Return Packet
Function
OSD Menu Set
Move OSD arrow to left.
Return Packet
Function
OSD Menu Right
Move OSD arrow to down.
Command Packet
Move to upper menu.
Command Packet
A0h
CAM ID
HOST ADDR
02
Return Packet
A0h
CAM ID
HOST ADDR
02
48_ SAMSUNG-T Protocol Command Description
0010h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0010h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0004h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0004h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0002h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0002h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
DDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
English_49
● SAMSUNG-T PROTOCOL COMMAND DESCRIPTION
DDR
MEMO
MEMO
MEMO
MEMO
MEMO
MEMO
SALES NETWORK
•
•
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Toll Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
•
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
www.samsungtechwin.com
www.samsungsecurity.com
P/No. : Z6806131601A