Alpine IVA-D100R Owner`s manual

Alpine IVA-D100R Owner`s manual
EN
FOR CAR USE ONLY
R
Advanced Video Interface for iPod
R
KCE- 425i
R
OWNER'S MANUAL
Please read before using this equipment
Package Contents
EN
Package Contents:
KCE-425i
iPod Cable (2m)
Power Cable (0.5m)
IR Remote Eye with 3.5mm Jack (4.5m)
IR Remote Control
02
Contents
EN
Precautions
Introduction
..........................................4
..........................................5
Remote
On Screen Navigation
My Jukebox
Viewing Photos on Screen
Switching OSD Languages
..........................................6
..........................................8
..........................................9
........................................10
........................................12
Tips and Trouble Shooting
Switching Video Formats
Technical Specifications
iPod Compatibility
Using RUE-4191
........................................13
........................................14
........................................17
........................................18
........................................21
Installation
03
Precautions
EN
EN
WARNING
This symbol means important instructions.
Failure to heed them can result in serious
DO NOT WATCH VIDEO WHILE DRIVING.
Watching the video may distract the driver from
looking ahead of the vehicle and cause an accident.
DO NOT OPERATE ANY FUNCTION THAT TAKES
YOUR ATTENTION AWAY FROM SAFELY DRIVING
YOUR VEHICLE.
Any function that requires your prolonged attention
should only be performed after coming to a complete
stop. Always stop the vehiclein a safe location before
performing these functions. Failure to do so may
result in an accident.
MINIMIZE DISPLAY VIEWING WHILE DRIVING.
Viewing the display may distract the driver from
looking ahead of the vehicle and cause an accident.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric
shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE
GROUND.
(Check with your dealer if you are not sure.) Failure to
do so may result in fire, etc.
Operating Instructions
KEEP SMALL OBJECTS SUCH AS BOLTS OR
SCREWS OUT OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If
swallowed, consult a physician immediately.
USE THE CORRECT AMPERE RATING WHEN
REPLACING FUSES.
Failure to do so may result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may
result in fire.
USE THIS PRODUCT FOR MOBILE 12V
APPLICATIONS.
Use for other than its designed application may result
in fire, electric shock or other injury.
CAUTION
This symbol means important instructions. Failure
to heed them can result in injury or material
property damage
HALT USE IMMEDIATELY IF A PROBLEM
APPEARS.
Failure to do so may cause personal injury or damage
to the product. Return it to your authorized Alpine
dealer or the nearest Alpine Service Centre for
repairing.
04
Introduction
EN
With an available A/V input in your mobile multimedia system, this product
allows use of your iPod to:
· Play your music
· Playback video
· Display pictures in a slideshow
You will have full control of your iPod via:
· Infrared Remote Control
· Alpine touch screen or roof monitor
· Via the iPod itself
You can use the KCE-425i as source in:
· An Alpine mobile multimedia system with any touch screen monitor
· An Alpine Rear-Seat entertainment system with roof or touch screen monitor
· Any Rear-Seat entertainment system with A/V input
· Any Factory system with a matching A/V interface
This versatile add-on solution lets you connect your iPod to a monitor in your car and
enjoy all your iPod entertainment, including movies! The black-box KCE-425i not only
brings your current system up-to-date for watching movies, it gives you a
sophisticated user interface that works similar to iPod, with same convenience and
ease of use. Listen to your iPod music on your car system, watch iPod videos, even
listen to audio books and podcasts, too. It's the perfect solution for bringing the iPod
into an existing mobile multimedia system.
05
Remote Control
EN
Remote Control Functions
The Alpine KCE-425i lets you enjoy your iPod music through your in car multi media
system as well as playing your iPod movies through your in car screen.
You can either select your Music or Videos directly from your iPod (iPod Mode) when
not wishing to use the remote control, or switch to On-Screen Navigation Mode to
view, navigate and select your Music or Videos using Alpine KCE-425i's sleek OnScreen Navigation.
To switch between On-Screen Navigation and iPod Mode, use the Mode button on the
remote control. In iPod Mode, Videos and Photos will be send to your screen, provided
the TV Output on the iPod is enabled.
Refer to the remote control illustration for more information about the Alpine
KCE-425i's Remote Control.
06
Remote Control
EN
Remote Control Functions
MODE
POWER Interface On or Off
UP NAV ARROW
Toggle iPod Mode and
On-Screen Navigation Mode
LEFT NAV ARROW
DOWN NAV ARROW
VOLUME
ENTER
RIGHT NAV ARROW/SELECT
SELECT/MY JUKEBOX
Press and hold for My
Jukebox selection
If Enabled
PREVIOUS/REWIND
Press & hold to Rewind
REWIND/PREVIOUS PLAYLIST
SHUFFLE
Toggle between Off, Song
Shuffle and Album Shuffle
MUTE
PLAY/PAUSE
NEXT/FAST FORWARD
Press and hold to Fast forward
NEXT/PLAYLIST/FAST FORWARD
iPod Mode only
REPEAT
SCREEN SAVER
Shortcut to Screen Saver
07
Remote Control
EN
To Select Music or Video Using On Screen Navigation
Use On-Screen Navigation Mode to control and display your iPod’s Music and
Videos, including Playlists, TV Shows, Rentals, Movies, Albums, Artists, Songs,
Genres, Podcasts, etc.
1. Select Music or Videos from the Main Menu Screen
2. Select the category of Music or Video you would like to view: Playlists, Movies, TV
Shows, Artists, Albums, Songs, Podcasts, etc.
3. Scroll up or down to select the particular Song or Video you would like to play. Then
with the Song highlighted, press the EnterButton
or the Right Nav Arrow Button
.
ENTER
To return to the main menu during Video playback, push the Enter Button
on the
remote control. To return to the main menu from Audio playback keep pressing the
Left Nav Arrow Button
on the remote control until you return to the main menu.
ENTER
From the Main Menu Screen, you can also go immediately to your iPod’s Playlists and
choose one to listen to. You can even choose Shuffle Songs to play songs randomly
from your library.
Any time a track is playing from your iPod using the Alpine KCE-425i, the current track
info is displayed at the top of your screen with Album Art (if available). The Alpine KCE425i also displays a track countdown timer, the track progress bar, the name of your
iPod, as well as Album and Playlist information (if applicable).
08
Enjoying Your Music
EN
Using the My Jukebox Feature
The Alpine KCE-425i gives you the option of creating your own Playlists from your
iPod directly on your in car screen. You can select these on-the-fly Playlists using the
My Jukebox feature on the Main Menu Screen. Here’s how:
1. Select any Song from a playlist, artist or album. Then, press and hold the Enter
Button
on your Remote Control.
ENTER
2. When the Highlight Bar blinks, the song selection has been copied to your My
Jukebox Playlist on the Main Menu Screen.
3. After you have selected as many items as you want for your My Jukebox Playlist,
you may navigate back to the Main Menu Screen to play selections from My
Jukebox.
4. To clear your My Jukebox Playlist, simply select ClearList and hold.
NOTE: My Jukebox will not save a Playlist after an iPod is disconnected or if the Alpine
KCE-425i is powered off.
09
Viewing Photos on Screen
EN
Viewing Photos on Screen with the Alpine KCE-425i
To view pictures from your photo-compatible iPod, follow these easy steps:
1. Connect your iPod. Switch the KCE-425i to iPod Mode (MODE Button, top left on
the remote control)
2. Navigate, select and play a Slideshow from your iPod using the KCE-425i remote
control or the iPod controls.
NOTE: Be sure to select On under TVOut within Slideshow Settings on your iPod
menu. You can use the Remote Control’s Nav Arrow Buttons to make your selections.
3. Once you selected a slideshow from your library, start it with the Play button
NOTE: Enter/ Select will display the picutres on the iPod only
4. Control functions such as Play/Pause, Next Slide, Previous Slide from the comfort
of your seat with the Alpine KCE-425i Remote Control. Refer to the Remote illustration
to learn how to direct your photo slide shows using the Alpine KCE-425i Remote
Control.
NOTE: Unfortunately, the iPod nano (1st and 2nd Generation) and iPod Touch do not
currently support external playback of its internal photos. However, all music
functions, including On Screen Navigation, work great with all of them.
If you have questions or need help setting up your iPod for Photos and Slide shows,
please visit Apple Support at
www.apple.com/support/ipod.
10
Viewing Photos on Screen
EN
Controlling Your Photos in iPod Mode
MODE
POWER
iPod MENU UP
SELECT
Switch to iPod Mode
to view pictures
ENTER
iPod MENU DOWN
DOWN NAV ARROW
VOLUME
(If Enabled)
PREVIOUS PHOTO
PLAY/PAUSE SLIDE SHOW
NEXT PHOTO
MUTE SLIDE SHOW MUSIC
11
Settings
EN
Language
The Alpine KCE-425i has 9 different languages. Select yours from the
Alpine KCE-425i Settings/Languages.
Available Languages:
English
Spanish
French
German
Italian
Dutch
Japanese
Russian
Swedish
12
Tips & Troubleshooting
EN
Things to Understand About iPod Album Art*
The maximum size of Album Art available is 200 x 200 pixels from iPods with Video.
For the iPod nano, the maximum Album Art size is 100 x 100 pixels. It can take several
seconds to load artwork from your iPod. While the larger 200 x 200 pixel artwork is
loading, the Alpine KCE-425i will display smaller Album Art.
NOTE: You will see a Please Wait message if you attempt to use the remote while
your iPod is delivering Album Art to the Alpine KCE-425i.
If your current selection does not have any Album Art, or if the Album Art is unavailable,
the Alpine KCE-425i will display the icon below instead of Album Art.
no album art
*(if available)
13
Tips & Troubleshooting
EN
Switching Between NTSC and PAL
The Alpine KCE-425i default broadcast format is NTSC. However, it is PAL
compatible too. If you have a screen that is configured for PAL and your iPod’s video
format is set for PAL, simply select the PAL setting in Alpine KCE-425i Settings.
All Alpine screens are native NTSC screens, therefore we recommend that you set
your iPod and KCE-425i to NTSC video format for best picture quality.
To toggle between NTSC and PAL settings, follow the steps below:
NTSC to PAL
1. Be sure you are on the Main Menu Screen
NOTE:Your iPod must be removed from the Alpine KCE-425i before attempting to
change formats.
2. Press the Left Arrow Button
once, then the Down Arrow Button
Repeat.
This will switch your video output from NTSC to PAL.
once.
PAL to NTSC
1. Be sure you are on the Main Menu Screen
NOTE:Your iPod must be removed from the Alpine KCE-425i before attempting to
change formats.
2. Press the Left Arrow Button
once, then the Up Arrow Button
Repeat.
This will switch your video output from PAL to NTSC.
once.
14
Tips & Troubleshooting
EN
My Alpine KCE-425i isn’t working, what’s wrong?
First, be sure that your Alpine KCE-425i is powered on. Next, make sure that you are
in the desired mode - On-Screen Navigation Mode or iPodMode. To change modes,
simply push the Mode Button on your Remote Control. See Remote Control
Functions (page7)
Sometimes NEXT
seems not to work?
While Album art is loaded, the remote commands are not executed immediately. One
command will be stored and executed when the full album art is loaded. In the normal
menu screen, this blackout time usually starts 3 seconds after playback of a song
begins and can take 7 seconds, depending on the iPod model. In ‘Now Playing’ mode
the blackout starts immediately and takes up to 15 seconds.
Please refer to (page16)
My audio is distorted, how can I improve it?
Files on your iPod can come from many different sources (i.e. iTunes store, ripping
your own CDs, Podcasts etc.). The audio levels on these differ widely. The fixed
volume setting in the set-up menu leaves usually enough headroom to avoid distortion
by clipping. If this is not enough, enable the volume control (SETTINGS-AUDIO
SETTINGS-VARIABLE) and lower the volume as needed.
15
Tips & Troubleshooting
EN
I’ve selected a photo slideshow to play on my
screen, but it’s only playing on my iPod screen.
On your iPod, check to see that your TV Out setting under Video/Slideshow Settings
is set to either Ask or On. Your Video or Slideshow will not play on your screen
unless you select TV On when prompted by your iPod in the Ask setting, or you have
selected On under TV Out in Video Settings. Your iPod arrives in the Ask setting,
so you will have to select TV On each time you start up a Video or Photo Slideshow
unless you change your iPod Settings. Remember, iPod nano does not support
external photo slideshows. For more information see the NOTE on (page 10)
The Alpine KCE-425i sometimes seems to have a lag time before it
displays my iPod’s content like album art or song information. Why?
The response delay time, if any, is usually the Alpine KCE-425i waiting for information from the iPod. Hard-drive based iPods like the 5G iPod with video take longer
than flash based iPods like the iPod nano. How long it takes depends on how
much content is on the iPod and what information is being requested. For instance,
when you’ve selected ‘Now Playing’ on the Alpine KCE-425i that displays “large”
Album Art 200 x 200 pixels, (if available), it can take up to 20 seconds for the iPod
to access that art work. See Things to Understand About iPod Album Art (page
13) for more information.
16
Technical Specifications
EN
Inputs/Outputs
Left/Right Audio: analog audio output
Video: composite video output
S-Video: separated analog video output
Power Input: 11-15volts/dc
USB-A: standard universal serial bus, USB 2.0
(only to be used for firmware updates)
Remote Control
Battery: 3V, type CR2032 or equivalent
Television Video Format
NTSC/PAL (software switchable)
Note: Due to continuous product improvement, specifications are subject to change without notice
17
Technical Specifications
EN
iPod Models Supported
MUSIC COMPATIBILITY:
All Dockable iPods (excluding 3G & 4G iPod)
NOTE: Apple iPod models listed as of Sept 2008
18
Technical Specifications
EN
iPod Models Supported
Picture COMPATIBILITY:
All iPods with Colour Display
(excluding iPod 4G, nano 1G, nano 2G,
iPod Touch 1G & 2G)
NOTE: Apple iPod models listed as of Sept 2008
19
Technical Specifications
EN
iPod Models Supported
VIDEO COMPATIBILITY:
All iPods with Video capability
NOTE: Apple iPod models listed as of Sept 2008
20
Alternative Remote Control
EN
Alpine RUE-4191 Universal Remote Controller
NAV.
A UDIO
EXT DVD
A.PROC.
POWER
BAND
PLAY/PAUSE
NEXT/FF
PREVIOUS/REV
V. SE L
SOURCE
.
M
TILT
U
MEN
P
SETU
ENTER
L
VOLUME
(if enabled)
1
ROUTE
FASTFORWARD
POS.
3
VOI CE
4
5
6
7
8
9
DEL.
0
DES T.
AUDIO
NAV JOYSTICK
(up, down, left, right)
Select (Push)
DISP/
TOP.M
RETURN
2
PUSH TV/MONI..
EXT DVD AUDIO NAV.
MADE IN CHINA
REWIND
SHUFFLE
DON'T LEAVE THE SET IN HIGH
TEMPRETURE SUCH AS
DIRECT SUNLIGHT.
T
O. P
REAR
E
OD
MAIN SELECTOR
SWITCH TO
EXT DVD FOR iPOD
10
TEL
OK M PT
SUB. T
ANGLE
DEL.DEST.
RUE-4191
R
21
Precautions
WARNING
MAKE THE CORRECT CONNECTIONS
Failure to make the proper connections may result in
fire or product damage.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE
GROUND.
(Check with your dealer if you are not sure.) Failure
to do so may result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE
FROM THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury
due to electrical shorts.
DO NOT ALLOW CABLES TO BECOME
ENTANGLED IN SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the
manual to prevent obstructions when driving. Cables
or wiring that obstruct or hang up on places such as
the steering wheel, shift lever, brake pedals, etc. can
be extremely hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to
other equipment. Doing so will exceed the current
carrying capacity of the wire and result in fire or
electric shock.
EN
Installation and Connections
DO NOT DAMAGE PIPE OR WIRING WHEN
DRILLING HOLES.
When drilling holes in the chassis for installation,
take precautions so as not to contact, damage or
obstruct pipes, fuel lines, tanks or electrical wiring.
Failure to take such precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE
OR STEERING SYSTEMS TO MAKE GROUND
CONNECTIONS.
Bolts or nuts used for the brake or steering
systems (or any other safety-related system), or
tanks should NEVER be used for installations or
ground connections. Using such parts could
disable control of the vehicle and cause fire etc.
KEEP SMALL OBJECTS SUCH AS BOLTS OR
SCREWS OUT OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If
swallowed, consult a physician immediately.
DO NOT INSTALL IN LOCATIONS WHICH
MIGHT HINDERVEHICLE OPERATION, SUCH
AS THE STEERING WHEEL OR SHIFT LEVER.
Doing so may obstruct forward vision or hamper
movement etc. and results in serious accident.
22
Precautions
CAUTION
EN
Installation and Connections
HAVE THE WIRING AND INSTALLATION DONE
BY EXPERTS.
The wiring and installation of this unit requires
special technical skill and experience. To ensure
safety, always contact the dealer where you
purchased this product to have the work done.
Precautions
USE SPECIFIED ACCESSORY PARTS AND
INSTALL THEM SECURELY.
Be sure to use only the specified accessory parts.
Use of other than designated parts may damage this
unit internally or may not securely install the unit in
place. This may cause parts to become loose
resulting in hazards or product failure.
• Be sure to connect the colour coded leads
according to the diagram. Incorrect connections
may cause the unit to malfunction or damage to the
vehicle’s electrical system.
ARRANGE THE WIRING SO IT IS NOT CRIMPED
OR PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts
(like the seat rails) or sharp or pointed edges. This
will prevent crimping and damage to the wiring. If
wiring passes through a hole in metal, use a rubber
grommet to prevent the wire’s insulation from being
cut by the metal edge of the hole.
• Be sure to disconnect the cable from the (–)
battery post before installing your KCE-425i. This
will reduce any chance of damage to the unit in case
of a short-circuit.
• When making connections to the vehicle’s
electrical system, be aware of the factory installed
components (e.g. on-board computer). Do not tap
into these leads to provide power for this unit. When
connecting the KCE-425i to the fuse box, make sure
the fuse for the intended circuit of the KCE-425i has
the appropriate amperage. Failure to do so may
result in damage to the unit and/or the vehicle.
When in doubt, consult your ALPINE dealer.
DO NOT INSTALL IN LOCATIONS WITH HIGH
MOISTURE OR DUST.
Avoid installing the unit in locations with high
incidence of moisture or dust. Moisture or dust that
penetrates into this unit may result in product failure.
23
Connections
EN
Connection Diagram
DVD PLAYER
FACTORY SCREEN
iPod (NOT SUPPLIED)
KCE-425i
GND
BATT
ACC
CAR SPECIFIC
A/V INTERFACE
R
POWER SUPPLY
AUDIO
EXTERNAL
REMOTE EYE
L
VIDEO
iPod IN
ENTER
S-VIDEO OUT
REMOTE EYE INPUT
UPDATE PORT
I/O PORT
24
Connections
EN
Connection Diagram
Note: Make sure to set the
selected AUX input of your Alpine
touchscreen to 'EXT DVD’
TOUCH MONITOR CONTROLS*
ENTER RETURN
MENU
P 1/2
TOP
MENU
P 2/2
TOUCH MONITOR
iPod (NOT SUPPLIED)
IVA-D310R
KCE-425i
GND
BATT
ACC
*Please note that only basic controls
are available on some models
R
POWER SUPPLY
AUDIO
L
VIDEO
iPod IN
S-VIDEO OUT
To Remote-Out line of
Alpine touchscreen
monitor (white-brown)
REMOTE EYE INPUT
UPDATE PORT
I/O PORT
COMPATIBLE PRODUCTS:
IVA-D100R, IVA-D105R, IVA-D106R
IVA-D310R/RB, IVA-W200Ri, IVA-W202R
IVA-W205R, IVA-W502R, IVA-W505R
TME-M740BT, TME-M770S, TME-M860
25
Connections
EN
Connection Diagram
Note: Make sure to set the
selected AUX input of your Alpine
overhead monitor to 'EXT DVD’
ENT
/
CONTROLS
To Remote-Out line of Alpine
overhead monitor (white-brown)
iPod (NOT SUPPLIED)
KCE-425i
GND
BATT
ACC
R
POWER SUPPLY
AUDIO
L
VIDEO
iPod IN
S-VIDEO OUT
COMPATIBLE PRODUCTS:
REMOTE EYE INPUT
UPDATE PORT
I/O PORT
PKG-1000P
PKG-2000P
PKG-850P
26
EN
Support and manuals in other languages available at:
www.alpine-europe.com
Guide d'utilisateur disponsible sur:
www.alpine-electronics.fr
27
ALPINE ELECTRONICS MARKETING,
INC.
1-1-8 Nishi Gotanda,Shinagawa-ku,
Tokyo 141-0031, Japan
Phone 03-5496-8231
ALPINE ELECTRONICS GmbH
Wilhelm-Wagenfeld-Str. 1-3,
80807 München, Germany
Phone 089-32 42 640
ALPINE ELECTRONICS OF AMERICA,
INC.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF U.K. LTD.
Alpine House
Fletchamstead Highway, Coventry CV4
9TW,U.K.
Phone 0870-33 33 763
ALPINE ELECTRONICS OF CANADA,
INC.
7300 Warden Ave., Suite 203,
Markham,Ontario L3R 9Z6, Canada
Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS FRANCE S.A.R.L.
(RCS PONTOISE B 338 101 280)
98, Rue de la Belle Etoile, Z.I. Paris Nord Il,
B.P. 50016, 95945 Roissy Charles de Gaulle
Cedex, France
Phone 01-48638989
ALPINE ELECTRONICS OF ASIA PACIFIC
CO, LTD.
555 Rasa Tower 1, Unit 2601-2602, 26th
Floor, Phaholyothin Rd.
Chatuchak, Bangkok, Thailand 10900
Phone: 662 (937) 0505
Fax: 662 (937) 0569
ALPINE ELECTRONICS OF AUSTRALIA
PTY. LTD.
6-8 Fiveways Boulevarde Keysborough,
Victoria 3173, Australia
Phone 03-9769-0000
ALPINE ITALIA S.p.A.
Viale C. Colombo 8, 20090 Trezzano
Sul Naviglio (MI), Italy
Phone 02-484781
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Portal de Gamarra 36, Pabellón 32
01013 Vitoria (Alava)-APDO 133, Spain
Phone 945-283588
R
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement