IP Office Essential Edition Norstar Version Installation

IP Office Essential Edition Norstar Version Installation
IP Office 7.0
IP Office Essential Edition - Norstar
Version Installation
15-601042 Issue 23f - (20 April 2011)
© 2011 AVAYA All Rights Reserved.
Notices
While reasonable efforts have been made to ensure that the information in
this document is complete and accurate at the time of printing, Avaya
assumes no liability for any errors. Avaya reserves the right to make changes
and corrections to the information in this document without the obligation to
notify any person or organization of such changes.
Documentation disclaimer
Avaya shall not be responsible for any modifications, additions, or deletions
to the original published version of this documentation unless such
modifications, additions, or deletions were performed by Avaya.
End User agree to indemnify and hold harmless Avaya, Avaya's agents,
servants and employees against all claims, lawsuits, demands and judgments
arising out of, or in connection with, subsequent modifications, additions or
deletions to this documentation, to the extent made by End User.
Link disclaimer
Avaya is not responsible for the contents or reliability of any linked Web sites
referenced within this site or documentation(s) provided by Avaya. Avaya is
not responsible for the accuracy of any information, statement or content
provided on these sites and does not necessarily endorse the products,
services, or information described or offered within them. Avaya does not
guarantee that these links will work all the time and has no control over the
availability of the linked pages.
Warranty
Avaya provides a limited warranty on this product. Refer to your sales
agreement to establish the terms of the limited warranty. In addition, Avaya’s
standard warranty language, as well as information regarding support for this
product, while under warranty, is available to Avaya customers and other
parties through the Avaya Support Web site: http://www.avaya.com/support.
Please note that if you acquired the product from an authorized Avaya reseller
outside of the United States and Canada, the warranty is provided to you by
said Avaya reseller and not by Avaya.
Licenses
THE SOFTWARE LICENSE TERMS AVAILABLE ON THE AVAYA WEBSITE,
HTTP://SUPPORT.AVAYA.COM/LICENSEINFO/ ARE APPLICABLE TO ANYONE
WHO DOWNLOADS, USES AND/OR INSTALLS AVAYA SOFTWARE,
PURCHASED FROM AVAYA INC., ANY AVAYA AFFILIATE, OR AN AUTHORIZED
AVAYA RESELLER (AS APPLICABLE) UNDER A COMMERCIAL AGREEMENT
WITH AVAYA OR AN AUTHORIZED AVAYA RESELLER. UNLESS OTHERWISE
AGREED TO BY AVAYA IN WRITING, AVAYA DOES NOT EXTEND THIS
LICENSE IF THE SOFTWARE WAS OBTAINED FROM ANYONE OTHER THAN
AVAYA, AN AVAYA AFFILIATE OR AN AVAYA AUTHORIZED RESELLER, AND
AVAYA RESERVES THE RIGHT TO TAKE LEGAL ACTION AGAINST YOU AND
ANYONE ELSE USING OR SELLING THE SOFTWARE WITHOUT A LICENSE. BY
INSTALLING, DOWNLOADING OR USING THE SOFTWARE, OR AUTHORIZING
OTHERS TO DO SO, YOU, ON BEHALF OF YOURSELF AND THE ENTITY FOR
WHOM YOU ARE INSTALLING, DOWNLOADING OR USING THE SOFTWARE
(HEREINAFTER REFERRED TO INTERCHANGEABLY AS “YOU” AND “END
USER”), AGREE TO THESE TERMS AND CONDITIONS AND CREATE A
BINDING CONTRACT BETWEEN YOU AND AVAYA INC. OR THE APPLICABLE
AVAYA AFFILIATE (“AVAYA”).
Avaya grants End User a license within the scope of the license types
described below. The applicable number of licenses and units of capacity for
which the license is granted will be one (1), unless a different number of
licenses or units of capacity is specified in the Documentation or other
materials available to End User. "Designated Processor" means a single
stand-alone computing device. "Server" means a Designated Processor that
hosts a software application to be accessed by multiple users. "Software"
means the computer programs in object code, originally licensed by Avaya
and ultimately utilized by End User, whether as stand-alone products or
pre-installed on Hardware. "Hardware" means the standard hardware
originally sold by Avaya and ultimately utilized by End User.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
License types
Designated System(s) License (DS). End User may install and use each copy
of the Software on only one Designated Processor, unless a different number
of Designated Processors is indicated in the Documentation or other materials
available to End User. Avaya may require the Designated Processor(s) to be
identified by type, serial number, feature key, location or other specific
designation, or to be provided by End User to Avaya through electronic means
established by Avaya specifically for this purpose.
Copyright
Except where expressly stated otherwise, no use should be made of materials
on this site, the Documentation(s) and Product(s) provided by Avaya. All
content on this site, the documentation(s) and the product(s) provided by
Avaya including the selection, arrangement and design of the content is
owned either by Avaya or its licensors and is protected by copyright and other
intellectual property laws including the sui generis rights relating to the
protection of databases. You may not modify, copy, reproduce, republish,
upload, post, transmit or distribute in any way any content, in whole or in
part, including any code and software. Unauthorized reproduction,
transmission, dissemination, storage, and or use without the express written
consent of Avaya can be a criminal, as well as a civil, offense under the
applicable law.
Third Party Components
Certain software programs or portions thereof included in the Product may
contain software distributed under third party agreements ("Third Party
Components"), which may contain terms that expand or limit rights to use
certain portions of the Product ("Third Party Terms"). Information regarding
distributed Linux OS source code (for those Products that have distributed the
Linux OS source code), and identifying the copyright holders of the Third
Party Components and the Third Party Terms that apply to them is available
on the Avaya Support Web site: http://support.avaya.com/Copyright.
Preventing toll fraud
"Toll fraud" is the unauthorized use of your telecommunications system by an
unauthorized party (for example, a person who is not a corporate employee,
agent, subcontractor, or is not working on your company's behalf). Be aware
that there can be a risk of toll fraud associated with your system and that, if
toll fraud occurs, it can result in substantial additional charges for your
telecommunications services.
Avaya fraud intervention
If you suspect that you are being victimized by toll fraud and you need
technical assistance or support, call Technical Service Center Toll Fraud
Intervention Hotline at +1-800-643-2353 for the United States and Canada.
For additional support telephone numbers, see the Avaya Support Web site:
http://support.avaya.com
Suspected security vulnerabilities with Avaya products should be reported to
Avaya by sending mail to: [email protected]
Trademarks
Avaya and Aura are trademarks of Avaya, Inc.
The trademarks, logos and service marks (“Marks”) displayed in this site, the
documentation(s) and product(s) provided by Avaya are the registered or
unregistered Marks of Avaya, its affiliates, or other third parties. Users are
not permitted to use such Marks without prior written consent from Avaya or
such third party which may own the Mark. Nothing contained in this site, the
documentation(s) and product(s) should be construed as granting, by
implication, estoppel, or otherwise, any license or right in and to the Marks
without the express written permission of Avaya or the applicable third party.
Avaya is a registered trademark of Avaya Inc. All non-Avaya trademarks are
the property of their respective owners.
Downloading documents
For the most current versions of documentation, see the Avaya Support Web
site: http://www.avaya.com/support
Contact Avaya Support
Avaya provides a telephone number for you to use to report problems or to
ask questions about your product. The support telephone number is
1-800-242-2121 in the United States. For additional support telephone
numbers, see the Avaya Web site: http://www.avaya.com/support
Page 2
15-601042 Issue 23f (20 April 2011)
Contents
Contents
1. System Overview
1.1 IP Office Modes
..................................................................... 9
............................................................................
10
1.1.1 Hardware
Support Summary
1.1.2 Feature
Support Summary
............................................................................
11
1.2 IP500v2 System
.....................................................................
Components
12
1.3 Control Unit.....................................................................
Cards
14
............................................................................
14
1.3.1 IP500
Base Cards
1.3.2 IP500
Trunk Cards
............................................................................
16
1.4 External Expansion
.....................................................................
Modules
17
1.4.1 IP500
............................................................................
External Expansion Modules
18
.....................................................................
19
1.5 Power Supplies
and Cables
1.5.1 Power
Supplies
............................................................................
19
1.5.2 Power
............................................................................
Supply Cords
20
1.5.3 Power
............................................................................
Supply Backup
21
............................................................................
22
1.5.4 Cabling
and Cables
1.5.5 Grounding
............................................................................ 24
1.5.6 Lightning Protection/Out-of-Building
............................................................................ 25
Connections
1.6 Wall and Rack
.....................................................................
Mounting
26
1.7 Feature Keys
and Licenses
.....................................................................
28
..................................................................... 29
1.8 IP Office Phones
1.9 SIP Trunks..................................................................... 30
1.10 Supported.....................................................................
Country Locales
31
1.11 IP Office Software
.....................................................................
Applications
32
1.12 Training ..................................................................... 34
1.13 Web Sites..................................................................... 34
1.14 Emergency
.....................................................................
and Power Failure Ports
35
2. Installation Requirements
2.1 Environmental
.....................................................................
Requirements
2.2 Space Requirements
.....................................................................
2.2.1 IP500
and IP500v2 Control Units
............................................................................
2.2.2 External
Expansion Modules
............................................................................
2.2.3 Wall
............................................................................
Mounting
2.2.4 Rack
............................................................................
Space Requirements
38
39
40
40
41
43
3. IP Office Administration Software
3.1 Installing the
.....................................................................
Admin Applications
3.2 Installer PC.....................................................................
Connection
3.3 Starting Manager
.....................................................................
.....................................................................
3.4 Starting System
Status
3.5 Starting Monitor
.....................................................................
3.6 Phone Based
.....................................................................
Administration
47
49
50
51
52
52
4. IP500v2 Installation
4.1 Tools and Equipment
.....................................................................
Required
4.2 Documentation
.....................................................................
4.3 Unpacking .....................................................................
4.4 SD Card Preparation
.....................................................................
4.4.1 Upgrade
............................................................................
the Card Firmware
4.4.2 Adding
............................................................................
a Pre-Built Configuration File
4.4.3 Creating
............................................................................
a Configuration File
4.4.4 Adding
............................................................................
a License File
4.4.5 Adding
............................................................................
Music on Hold Files
4.5 IP500 Card.....................................................................
Installation
4.5.1 IP500
............................................................................
Daughter Card Preparation
55
56
57
58
58
58
60
61
61
62
63
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
............................................................................
4.5.2 IP500
Card Insertion
4.6 Wall Mounting
.....................................................................
4.6.1 Wall
............................................................................
Mounting Kit V2
............................................................................
4.6.2 Wall
Mounting Kit V1
4.7 Rack Mounting
.....................................................................
4.8 Connecting.....................................................................
External Expansion Modules
4.9 Grounding .....................................................................
.....................................................................
4.10 Network Connection
4.11 Starting the
System
.....................................................................
4.11.1............................................................................
Checking the LEDs
4.12 Changing.....................................................................
the System to Standard Mode
.....................................................................
4.13 Connecting
Phones
64
65
66
68
69
71
73
74
75
76
77
78
5. Initial Configuration
5.1 Setting the .....................................................................
System Locale
5.2 Select Key .....................................................................
System or PBX System Mode
5.3 Changing the
.....................................................................
IP Address Settings
5.4 Changing the
.....................................................................
Default Passwords
.....................................................................
5.5 Extension Numbering
5.6 Entering Licenses
.....................................................................
81
82
83
84
85
86
6. Additional Processes
6.1 Switching Off
.....................................................................
an IP Office System
91
6.2 Rebooting .....................................................................
an IP Office System
92
6.3 Memory Card
Removal
.....................................................................
93
6.4 Changing Components
..................................................................... 95
6.5 Upgrading .....................................................................
the IP Office Software
97
............................................................................
98
6.5.1 Using
the Upgrade Wizard
6.5.2............................................................................
Using an SD Card
100
6.6 Out of Building
.....................................................................
Telephone Installations
101
6.6.1............................................................................
DS Phones
102
103
6.6.2............................................................................
Analog Phone Barrier Box
6.6.3............................................................................
Rack Mounting Barrier Boxes
104
6.7 Using the .....................................................................
External Output Port
105
6.7.1............................................................................
Port Connection
105
..................................................................... 106
6.8 Reset Button
6.9 AUX Button
..................................................................... 106
6.10 DTE Port.....................................................................
Maintenance
107
6.10.1
DTE Port Settings
............................................................................
107
............................................................................
108
6.10.2
Erasing the Configuration
6.10.3
Defaulting Security Settings
............................................................................
110
6.10.4
............................................................................
Erasing the Operational Firmware
111
7. SD Card Management
7.1 Booting from
.....................................................................
the SD Cards
7.2 Creating an
.....................................................................
IP Office SD Card
7.3 Viewing the
Card Contents
.....................................................................
7.4 Backing Up
.....................................................................
the System SD Card
7.4.1............................................................................
Backing Up the Primary Folder
7.4.2............................................................................
Restore from the Backup Folder
7.4.3............................................................................
Backing Up to the Optional Card
7.4.4............................................................................
Restoring from the Optional Card
7.5 Upgrading.....................................................................
Card Software
7.5.1............................................................................
Upgrading Remotely Using Manager
7.5.2............................................................................
Upgrading the SD Card Locally
7.5.3............................................................................
Upgrading Using an Optional SD Card
7.6 Removing.....................................................................
SD Cards
7.6.1............................................................................
Card Shutdown
7.6.2............................................................................
Card Startup
117
119
120
121
121
122
123
124
126
127
127
128
129
129
130
Page 3
15-601042 Issue 23f (20 April 2011)
7.6.3............................................................................
System Shutdown
131
8. System Components
8.1 IP500v2 Control
.....................................................................
Unit
8.2 IP500 Base
.....................................................................
Cards
8.2.1............................................................................
Analog Phone
8.2.2............................................................................
ATM Combination Card
8.2.3............................................................................
BRI Combination Card
8.2.4............................................................................
Digital Station
8.2.5............................................................................
TCM8 Digital Station
.....................................................................
8.3 IP500 Trunk
Daughter Cards
8.3.1............................................................................
Analog Trunk Card
8.3.2............................................................................
BRI Trunk Cards
8.3.3............................................................................
PRI Trunk Cards
.....................................................................
8.4 IP500 Expansion
Modules
8.4.1............................................................................
Digital Station
8.4.2............................................................................
Digital Station A
8.4.3............................................................................
Phone
.....................................................................
8.5 Feature Keys
8.5.1............................................................................
IP500v2 System SD Cards
8.6 Mounting .....................................................................
Kits
8.6.1............................................................................
IP500 Wall Mounting Kits
8.6.2............................................................................
IP500 Rack Mounting Kit
8.6.3............................................................................
IP400 Rack Mounting Kit
8.6.4............................................................................
Barrier Box Rack Mounting Kit
8.7 Phones .....................................................................
8.7.1............................................................................
1403
8.7.2............................................................................
1408
8.7.3............................................................................
1416
8.7.4............................................................................
9404
8.7.5............................................................................
9408
8.7.6............................................................................
9504
8.7.7............................................................................
9508
8.7.8............................................................................
Audio Conferencing Unit
8.7.9............................................................................
M7100
8.7.10
M7100N
............................................................................
............................................................................
8.7.11
M7208
8.7.12
M7208N
............................................................................
8.7.13
............................................................................
M7310
8.7.14
M7310N
............................................................................
............................................................................
8.7.15
M7324
8.7.16
M7324N
............................................................................
8.7.17
............................................................................
T7000
8.7.18
............................................................................
T7100
8.7.19
T7208
............................................................................
8.7.20
............................................................................
T7316
8.7.21
............................................................................
T7316E
8.7.22
............................................................................
T7406, T7406e
8.8 Phone Add-Ons
.....................................................................
8.8.1............................................................................
DBM32
8.8.2............................................................................
KLM Module
8.8.3............................................................................
T7316e KEM
8.9 Ancilliary Systems
.....................................................................
8.9.1............................................................................
Digitial Mobility Solution
8.10 Applications
.....................................................................
8.10.1
............................................................................
Manager
8.10.2
............................................................................
Monitor
8.10.3
............................................................................
System Status Application (SSA)
135
137
139
140
141
142
143
144
145
146
147
148
149
151
154
156
156
158
158
159
159
159
160
161
162
163
164
164
165
165
166
167
167
168
168
169
169
170
170
171
171
172
173
174
175
176
177
178
179
180
180
181
181
182
183
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
............................................................................
8.10.4
TAPI
8.10.5
............................................................................
IP Office Ports
8.11 Physical.....................................................................
Ports
............................................................................
8.11.1
Cables
8.11.2
ANALOG Port
............................................................................
8.11.3
............................................................................
AUDIO Port
8.11.4
............................................................................
BRI Port (To)
............................................................................
8.11.5
DC I/P Port
8.11.6
DS Ports
............................................................................
8.11.7
............................................................................
RS232 DTE Port
8.11.8
............................................................................
EXPANSION Port
............................................................................
8.11.9
EXT O/P Port
8.11.10
LAN Port
............................................................................
8.11.11
............................................................................
PF Port
8.11.12
............................................................................
PHONE (POT) Port
............................................................................
8.11.13
PRI Port
8.11.14
TCM Port (RJ21)
............................................................................
8.11.15
............................................................................
TCM Port (RJ45)
8.12 Licences.....................................................................
............................................................................
8.12.1
System Edition Licenses
8.12.2
Trunk Licensing
............................................................................
8.12.3
............................................................................
User Licenses
8.12.4
Trial Licenses
............................................................................
184
185
188
189
191
191
192
193
193
194
195
195
196
197
198
199
200
201
202
203
204
205
206
9. Safety Statements
9.1 Lithium Batteries
..................................................................... 210
9.2 Lightning .....................................................................
Protection/Hazard Symbols
210
9.3 Trunk Interface
Modules
.....................................................................
211
.....................................................................
212
9.4 Further Information
and Product Updates
9.5 Port Safety
Classification
.....................................................................
212
9.6 EMC Directive
..................................................................... 213
9.7 Regulatory
Instructions for Use
.....................................................................
214
214
9.7.1............................................................................
Australia
9.7.2............................................................................
Canada
214
9.7.3............................................................................
China
215
9.7.4............................................................................
European Union
216
216
9.7.5............................................................................
New Zealand
9.7.6............................................................................
FCC Notification
217
9.7.7............................................................................
Compliance with FCC Rules
219
Index ...............................................................................221
Page 4
15-601042 Issue 23f (20 April 2011)
Chapter 1.
System Overview
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 5
15-601042 Issue 23f (20 April 2011)
System Overview:
1. System Overview
This documentation is intended to assist with the installation of the core components of an Avaya IP Office Essential
Edition - Norstar Version mode telephone system. It describes those components and factors that should be considered
for an installation.
· The IP Office is a converged voice and data communications system. It should therefore only be installed by
persons with telephony experience.
· Installers must be trained on IP Office systems. Through its Avaya University 34 (AU), Avaya provides a range of
training courses including specific IP Office implementation and installation training. It also provides certification
schemes for installers to achieve various levels of IP Office accreditation.
· It is the installer’s responsibility to ensure that all installation work is done in accordance with local and national
regulations and requirements. It is also their responsibility to accurately establish the customer’s requirements
before installation and to ensure that the installation meets those requirements.
· You should read and understand this documentation before installation. You should also obtain and read the Avaya
Technical Bulletins relevant to recent IP Office software and hardware releases to ensure that you are familiar with
any changes to the IP Office equipment and software.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 7
15-601042 Issue 23f (20 April 2011)
Additional Documentation
The following components of IP Office are outside the range of a basic IP Office installation. They are covered by separate
installation and configuration documentation. If those components are to be part of the IP Office system installation, that
documentation should be obtained, read and understood prior to the installation.
· IP Office Product Description
Covers the features provided by IP Office 7.0 - IP Office Essential Edition - Norstar Version.
· IP Office Essential Edition - Norstar Version Installation Manual
Covers the equipment supported and the installation of that equipment.
· IP Office Essential Edition - Norstar Version Manager
Covers the system programming that can be performed using the IP Office Manager application.
· IP Office Essential Edition - Norstar Version Phone Based Administration Manual
Covers the range of system programming that can performed from the first two extensions in the system.
·
IP Office Technical Bulletins
Ensure that you have obtained and read the IP Office Technical Bulletin relating to the IP Office software release
which you are installing. This bulletin will contain important information that may not have been included in this
manual. IP Office Technical Bulletins are available from the Avaya support website (http://support.avaya.com).
·
Upgrade Licenses
Some upgrades may require entry of upgrade licenses.
Equipment Availability
SAP codes and details of specific items within this documentation are for reference only. Items available in any specific
locale should be confirmed against the local Avaya IP Office price list for that locale. The local price list may also include
additional items relative to the installation requirements of that locale.
This documentation covers the equipment supported by IP Office Release 6. That includes equipment supported but no
longer available as new from Avaya.
Repair
IP Office systems do not contain any user serviceable or repairable components. If a faulty unit is suspected the whole
unit should be replace.
· IP400 control units should only be opened where indicated for the installation of IP400 cards.
· IP500 control units should not be opened under any circumstances.
RoHS
RoHS is a European Union directive for the Removal of Certain Hazardous Substances from Electrical and Electronic
Equipment. Similar legislation has been or is being introduced in a number of other countries. Avaya has decided to make
its global product range compliant with the requirements of RoHS.
The actions taken vary
· In some cases equipment has been discontinued and is no longer available from Avaya.
· In some cases new manufactured stock has been made RoHS compliant and keeps its existing SAP code.
· In other cases the equipment has been replaced by a new RoHS compliant alternative with new SAP codes.
· The SAP codes within this document are for RoHS compliant equipment unless otherwise stated.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 8
15-601042 Issue 23f (20 April 2011)
System Overview:
1.1 IP Office Modes
IP Office systems based on the IP500v2 control unit can run in a number of modes:
· IP Office Standard Version
· IP Office Essential Edition - Quick Version
· IP Office Essential Edition - Norstar Version
· IP Office Essential Edition - PARTNER® Version
· Avaya Branch Gateway
This is a special mode used for B5800 control units and is not covered by this documentation. Refer to the separate
Avaya Branch Gateway documentation.
IP500 control units only run in IP Office Standard Version mode. The default mode used for IP500v2 systems is
determined by the System SD card present when the system is first installed.
· IP Office U-Law
A system fitted with this type of card will default to U-Law telephony. For pre-IP Office Release 7.0 software,
the system will default to IP Office standard mode. For IP Office Release 7.0+, the system will default to IP
Office Essential Edition - Quick Version mode Key System operation. Intended for North American locales.
· IP Office A-Law
A system fitted with this type of card will default to A-Law telephony. For pre-IP Office Release 7.0 software,
the system will default to IP Office standard mode. For IP Office Release 7.0+, the system will default to IP
Office Essential Edition - Quick Version mode PBX System operation. Intended for locales outside North
America.
· IP Office Partner Version
A system fitted with this type of card will default to U-Law telephony and IP Office Essential Edition PARTNER® Version mode Key System operation. Supported only in North American locales.
· IP Office Norstar Version
A system fitted with this type of card will default to A-Law telephony and IP Office Essential Edition - Norstar
Version mode Key System operation. Supported only in Middle East and North African locales.
Overall Capacity
IP Office
Essential
Edition PARTNER®
Version
Extensions
Maximum Extensions
Trunks
Maximum Trunks
100
- Maximum Analog Trunks
[1]
IP Office
Essential
Edition Norstar
Version
100
[1]
IP Office
Essential
Edition Quick Version
100
[1]
IP Office
Standard
Version
384
64
64
64
[5]
208
32
32
32
- Maximum BRI Channels
[3]
–
12
12
32
- Maximum PRI Channels
[4]
24
30
30
120
- Maximum SIP Channels
[2]
20
20
20
[5]
–
–
–
[5]
- Maximum H323 IP Channels
1. 100 Extension in 3-digit extension numbering mode only. 48 extensions in 2-digit extension numbering mode.
· In non-IP Office Standard Version mode the system assumes that the base control unit is always fully
populated with up to 32 extensions, either real or phantom or a mix, to which it assigns extension numbers in
sequence. It does this before assigning extension numbers to any real extensions on attached external
expansion modules up to the system extension limit. If the system extension limit has not been exceeded, any
remaining extension numbers are assigned to additional phantom extensions.
2. Non-IP Office Standard Version mode systems support 3 SIP channels without licenses. Additional channels up to
the limit require licenses. IP Office Standard Version mode systems require licenses for all channels. In all modes,
voice compression hardware resources are also required for SIP support.
3. Non-IP Office Standard Version mode systems do not support both BRI and PRI trunks in the same system.IP Office
Standard Version mode systems support both BRI and PRI trunks in the same system.
4. Non-IP Office Standard Version mode systems are restricted to 12 BRI channels regardless of the BRI hardware
installed.
5. Capacity is dependent on licenses, voice compression resources and available bandwidth.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 9
15-601042 Issue 23f (20 April 2011)
1.1.1 Hardware Support Summary
Note that even where indicated as supported, the availability and support of equipment may still be subject to local
restrictions.
Control Unit
IP Office
Essential
Edition PARTNER®
Version
IP Office
Essential
Edition Norstar
Version
IP Office
Essential
Edition Quick Version
–
–
–
IP500v2 Control Unit
IP500 Control Unit
IP500 Base
Cards
IP Office
Standard
Version
IP500 Digital Station Card
3
3
3
3
IP500 Analog Phone 2/8 Cards
4
4
4
4
4
4
4
4
IP500 TCM8 Card
[1]
IP500 VCM 32/64 Base Cards
–
–
–
IP500 Legacy Card Carrier
–
–
–
IP500 4-Port Expansion Card
–
–
–
IP500 BRI Combination Card
[1]
–
IP500 ATM Combination Card
2
2
1
2
2
2
2
2
[1]
IP500 ETR6 Card
[1]
IP500 Trunk
Analog Trunk Card
Daughter Cards
BRI Trunk Cards[5]
3
3
–
–
PRI Trunk Card[6]
External
Expansion
Modules
–
1
[3]
Number of Modules
1
1
8
8
8
–
–
–
4
12
Digital Station 16/30
Digital Station 16A/30A
Phone 8/16/30
Analog Trunk 16
BRI So8
Telephone
Types
ETR Phones (ETR ports)
–
–
BST Phones (TCM ports)
DS Phones (DS ports)
H323 IP Phones (LAN)
–
–
–
SIP IP Phones (LAN)
–
–
–
–
–
–
DECT R4 (LAN)
DECT DMS (TCM ports)
Voicemail
Embedded Voicemail
Voicemail Pro
1. Not supported by IP500 control units. Support by IP500v2 Control units only.
2. Only 2 combinations cards are supported in a control unit, regardless of type.
3. External expansion modules can be added so long as the overall limit for extensions and trunks is not exceeded. On
non-IP Office Standard Version mode systems, only a maximum of one Analog Trunk 16 module is supported.
4. A mix of BRI and PRI trunks is not supported by IP Office Essential Edition - Norstar Version and IP Office Essential
Edition - Quick Version.
5. IP Office Essential Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version and IP Office Essential
Edition - Quick Version only support a single-port PRI card.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 10
15-601042 Issue 23f (20 April 2011)
System Overview: IP Office Modes
1.1.2 Feature Support Summary
IP Office
Essential
Edition PARTNER®
Version
Administration
IP Office
Essential
Edition Norstar
Version
IP Office
Essential
Edition Quick Version
Phone Based Administration
–
Manager - Simplified View
IP Office
Applications
IP Office
Standard
Version
–
Manager - Advanced View
–
–
–
Customer Call Reporter
–
–
–
one-X Portal for IP Office
–
–
–
Phone Manager
–
–
–
SoftConsole
–
–
–
–
–
–
–
–
–
IP Office Manager
Monitor (System Monitor)
System Status Application
TAPI (1st Party)
TAPI (3rd Party)
Voicemail Pro
Locales
Voicemail
Languages
Canada,
Bahrain, Egypt, Argentina, Australia, Bahrain,
Mexico, United
Kuwait,
Belgium, Brazil, Canada, Chile,
States
Morocco,
China, Colombia, Denmark,
Oman,
Egypt, Finland, France,
Pakistan,
Germany, Greece, Hong Kong,
Qatar, Saudi
Hungary, Iceland, India, Italy,
Arabia, South Korea, Kuwait, Mexico, Morocco,
Africa, Turkey,
Netherlands, New Zealand,
United Arab
Norway, Oman, Pakistan, Peru,
Emirates
Poland, Portugal, Qatar, Russia,
Saudi Arabia, Singapore, South
Africa, Spain, Sweden,
Switzerland, Taiwan, Turkey,
United Arab Emirates, United
Kingdom, United States,
Venezuela.
Embedded Voicemail
Arabic, Chinese-Mandarin, Chinese-Cantonese, Danish, Dutch,
English-UK, English-US, Finnish, French, French-Canadian,
German, Italian, Korean, Norwegian, Portuguese, Portuguese
Brazilian, Russian, Swedish, Spanish, Spanish-Latin, SpanishArgentinean.
Voicemail Pro
–
–
–
As above plus:
Hungarian,
Greek, Polish.
Minus: Arabic.
User Name
Administrator
Administrator
Administrator
Administrator
Password
password
password
password
Administrator
Default Upgrade Password
password
password
password
password
Default
Configuration
Access
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 11
15-601042 Issue 23f (20 April 2011)
1.2 IP500v2 System Components
The following are the typical components of an IP Office system based on an IP500v2 control unit.
· IP Office IP500v2 System Unit 135
The control unit holds the main configuration and performs the
routing and switching for telephone calls and data traffic. Each
control unit includes 4 slots for optional base cards to support
trunk and phone extension ports.
·
Avaya SD Card 28
This uniquely numbered dongle is used to validate license
keys entered into the system's configuration to enable
features. A dongle is mandatory for correct system operation
even if no licensed features are being used. IP500v2 control
units use an Avaya SD card which is slotted into the rear of
the control unit. This card also provides embedded voicemail
support and storage for system software files.
· IP500 Base Cards 14
The IP500v2 control unit has slots for up to 4 IP500 base cards.
These can be used to add ports for analog extensions, digital
extensions, voice compression channels and other resources.
· IP500 Digital Station Base Card
· IP500 Analog Phone Base Card
· IP500 TCM8 Base Card
142
139
143
· IP500 Trunk Daughter Cards 16
Many of the IP500 base cards can be fitted with an IP500 daughter
card in order to support various types of trunk connections.
· IP500 Analog Trunk Card
· IP500 BRI Trunk Card
146
· IP500 PRI Trunk Card
147
145
· IP500 Combination Cards 14
These card are pre-paired base and daughter cards. They provide
6 digital station ports, 2 analog phone ports, 10 voice compression
channels and either 4 analog trunk ports or 4 BRI channels (2
ports). The trunk daughter card cannot be removed or replaced
with another type.
VK00nDd15SDvXoxkw9cR9x_jOXr_AWz9
· License Keys 206
Various IP Office features and applications require a license key to
be entered into the system's configuration. Each key is a 32character text string unique to the feature being activated and the
serial number of the Feature Key dongle installed in the system.
· IP500 External Expansion Modules 17
Additional ports can be added using a number of IP500 external
expansion modules.
· Systems running in IP Office Essential Edition - Norstar
Version mode support up to 8 external expansion modules so
long as the system extensions limit is not exceeded.
· Power Supplies 19
The IP500 control unit has an internal power supply unit. Each
external expansion module is supplied with an external power
supply unit. Additional power supply units may also be required for
IP phones and some phone add-ons.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 12
15-601042 Issue 23f (20 April 2011)
System Overview: IP500v2 System Components
· Power Cords 20
Depending on the locale, different power cords need to be ordered
for each control unit, external expansion module and any phones
or devices using external power supply units.
· Cables 22
The IP Office is designed primarily for connection to a structured
cabling system using CAT3 UTP cabling. This approach allows
telephone and data traffic to share the same wiring infrastructure
and simplifies equipment moves.
· Mounting Kits 26
The control unit can be used free-standing, with external
expansion modules stacked above it. With optional rack mounting
kits, the control unit and external expansion modules can also be
rack mounted. Alternatively with an optional wall mounting kit the
IP500 control unit can be wall mounted. IP500 external expansion
modules can also be wall mounted.
· Surge Protectors and Barrier Boxes 25
Where the installation includes extensions in other buildings
additional protective equipment is required. This equipment may
also be required in areas where the lightning risk is high.
· Phones 29
IP Office systems support a variety of Avaya digital and IP phones
plus analog phones.
· Application DVDs
The IP Office applications can be ordered on a number of DVDs. In
addition they can be downloaded from the IP Office section of the
Avaya support web site (http://support.avaya.com).
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 13
15-601042 Issue 23f (20 April 2011)
1.3 Control Unit Cards
1.3.1 IP500 Base Cards
The IP500 and IP500v2 control units have 4 slots for the insertion of IP500
base cards. The slots are numbered 1 to 4 from left to right. Normally they
can be used in any order, however if the capacity for a particular type of
card is exceeded, the card in the rightmost slot will be disabled.
Each base card includes an integral front panel with ports for cable
connections. Typically the first 8 ports on the left are for connection of
extension devices. The 4 ports on the left are used for connection of trunks
if a trunk daughter card 16 is added to the base card.
IP500 Digital Station Base Card
142
This card provides 8 DS (digital station) ports for the connection of
Avaya digital phones.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
16
which
· Maximum: 3 per control unit.
· Connections for 4100, 7400, M-Series and T-Series phones use
the IP500 TCM8 Digital Station card.
IP500 Analog Phone Base Card
139
The card is available in two variants, supporting either 2 or 8 analog
phone ports.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
16
which
· Maximum: 4 per control unit.
· The analog phone ports do not include a ringing capacitor. Where
this is a requirement, connection should be via a Master socket
containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during power
failure phone port 8 is connected to analog trunk port 12.
IP500 TCM8 Digital Station Card
143
This card provides 8 TCM (digital station) ports for the connection of
Avaya 4100, 7400, M-Series and T-Series phones.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
16
which
· Maximum: 4 per control unit per IP500v2 control unit.
IP500 BRI Combination Card
141
This card provides 6 digital station ports (1-6), 2 analog extension ports
(7-8) and 2 BRI trunk ports (9-10, 4 channels). The card also includes
10 voice compression channels.
· This card has a pre-installed IP500 BRI trunk daughter card
16
.
· Maximum: 2 combination cards per IP500v2 control unit, regardless
of type.
·
IP Office Essential Edition - Norstar Version mode systems are
limited to a maximum of 12 BRI channels.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 14
15-601042 Issue 23f (20 April 2011)
System Overview: Control Unit Cards
IP500 ATM Combination Card
140
This card provides 6 digital station ports (1-6), 2 analog extension ports
(7-8) and 4 analog trunk ports (9-12). The card also includes 10 voice
compression channels.
· This card has a pre-installed IP500 analog trunk daughter card
16
.
· Maximum: 2 combination cards per IP500v2 control unit, regardless
of type.
· The analog phone ports do not include a ringing capacitor. Where
this is a requirement, connection should be via a Master socket
containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during power
failure phone port 8 is connected to analog trunk port 12.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 15
15-601042 Issue 23f (20 April 2011)
1.3.2 IP500 Trunk Cards
Most IP500 base cards 14 can be fitted with an IP500 trunk daughter
cards to support the connection of trunks to the base card.
Each daughter card is supplied with the stand off pillars required for
installation and a label to identify the daughter cards presence on the
front of the base card after installation.
· IP500 Combination cards are pre-fitted with a trunk daughter card
which cannot be removed or changed for another type of trunk
daughter card.
IP500 Analog Trunk Daughter Card
145
This card allows the base card to support 4 analog loop-start trunks.
· The analog phone ports do not include a ringing capacitor.
Where this is a requirement, connection should be via a Master
socket containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during
power failure phone port 8 is connected to analog trunk port
12.
· Maximum: 4 per control unit.
IP500 PRI-U Trunk Daughter Card
147
This card allows the base card to support up to 2 PRI trunk
connections. The card is available in single and dual port variants.
The card can be configured for E1 PRI, T1 robbed bit, T1 PRI or E1R2
PRI trunks.
· Maximum: 1 single port card per control unit.
· The IP Office system supports 8 unlicensed B-channels on each
IP500 PRI-U port fitted. Additional B-channels, up to the capacity
of ports installed and PRI mode selected require IP500 Universal
PRI (Additional Channels) 204 licenses added to the
configuration. These additional channels consume the licenses
based on which additional channels are configured as in-service
from port 9 of slot 1 upwards. D-channels are not affected by
licensing.
IP500 BRI Trunk Daughter Card
146
This card allows the base card to support up to 4 BRI trunk
connections, each trunk providing 2B+D digital channels. The card is
available in 2 port (4 channels) and 4 port (8 channels) variants.
· Maximum: 4 per control unit.
·
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
IP Office Essential Edition - Norstar Version mode systems are
limited to a maximum of 12 BRI channels.
Page 16
15-601042 Issue 23f (20 April 2011)
System Overview: Control Unit Cards
1.4 External Expansion Modules
These modules can be used to add additional ports to an IP Office systems. The number of external expansion modules
supported depends on the control unit type. Each module uses an external power supply unit 19 supplied with the
module. A locale specific power cord 20 for the PSU must be ordered separately.
IP500 System with External Expansion Module
· Systems running in IP Office Essential Edition - Norstar Version mode support up to 8 external expansion modules
so long as the system extensions limit is not exceeded.
· Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This
cable must be used when connecting to expansion ports on the rear of a control unit.
IP500 External Expansion Modules
Expansion modules include an external power supply unit (PSU) and a 1m blue interconnect cable. They do not include a
locale specific power cord for the external PSU or any phone extension cables.
Variant
Country
SAP Code
Digital Station
IPO 500 Digital Station 16
All
700449499
IPO 500 Digital Station 30
All
700426216
IPO 500 Digital Station 16A
All
700500699
IPO 500 Digital Station 30A
All
700500698
IPO 500 Phone 16
All
700449507
IPO 500 Phone 30
All
700426224
North America
700449473
Analog Phone
Others
IPO 500 Analog Trunk 16
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 17
15-601042 Issue 23f (20 April 2011)
1.4.1 IP500 External Expansion Modules
The following IP500 external expansion modules are supported by IP Office Release 7.0. Each module uses an external
power supply unit 19 supplied with the module. A locale specific power cord 20 for the PSU must be ordered separately.
If being rack mounted, these units use the IP500 rack mounting kit. They can be wall mounted using the new wall
mounting kit V2.
· Systems running in IP Office Essential Edition - Norstar Version mode support up to 8 external expansion modules
so long as the system extensions limit is not exceeded.
· IP500 Digital Station Module 149
Provides, depending on variant, an additional 16 or 30 DS
supported Avaya DS digital phones 29 .
193
ports for
· IP500 Digital Station A Module 151
Provides, depending on variant, an additional 16 or 30 TCM 201 ports for
supported Avaya TCM digital phones 29 . Supported by IP500v2 only.
· IP500 Phone Module 154
Provides, depending on variant, an additional 16 or 30 PHONE
analog phones.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
198
ports for
Page 18
15-601042 Issue 23f (20 April 2011)
System Overview: External Expansion Modules
1.5 Power Supplies and Cables
All IP Office control units and external expansion modules either have an internal power supply unit or are supplied with
an external power supply unit.
1.5.1 Power Supplies
The IP500 and IP500v2 control units have an internal power supply unit and so only require a suitable locale specific
power cord 20 and a power outlet that includes a switch. Note that if the power cord includes an earth lead, the power
outlet must be connected to a protective earth.
External expansion modules are all supplied with an external power supply unit (PSU). These PSUs include an integral 1.5
meter lead for connection to the control unit or expansion module. A power cord 20 for connection from the PSU to the
power outlet is not included as this varies by locale. The appropriate power cord must be ordered separately or sourced
locally.
Additional power supply units are required for 4450, EU24, XM24 and T3 DSS add-on modules and may also be required
for Avaya IP phones.
Area
Type
IP Office Control 40W PSU
Units and
External
Expansion
Modules
60W Earthed
PSU
Used on:
Connector Type
Analog, Digital Station V1, Phone V1.
IEC60320 C7
IP400 Digital Station V2, IP400 Phone V2, IP400 So8, IP500
Phone 30, IP500 Digital Station 30, IP500 Digital Station
16A, IP500 Digital Station 30A.
IEC60320 C13
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 19
15-601042 Issue 23f (20 April 2011)
1.5.2 Power Supply Cords
Each control unit and expansion module requires a switched power outlet socket rated at 110-240V ac, 50-60Hz.
Connection from that power outlet socket requires an appropriate locale specific power cord which is not supplied with the
unit and must be ordered separately. Note that if the power cord includes an earth lead, the power outlet must be
connected to a protective earth.
Power cords must not be attached to the building surface or run through walls, ceilings, floors and similar openings.
Installation measures must be taken to prevent physical damage to the power supply cord, including proper routing of the
power supply cord and provision of a socket outlet near the fixed equipment or positioning of the equipment near a socket
outlet.
For locales not detailed below an appropriate power cord must be obtained locally.
Power Cord Type
Power Outlet Plug Type
Locales
SAP Codes
Earthed Power Cords (IEC60320 C13)
CEE7/7 (Schuko)
Europe and
South Africa.
700289762
Control Units
· IP500v2.
· IP500.
BS1363
Czech Republic, 700289747
Ireland, United
Kingdom.
NEMA5-15P / CS22.2
No.42
North, Central
and South
America.
700289770
Unearthed Power Cord (IEC60320 C7)
CEE7/16 (Europlug)
Europe and
South Africa.
700213382
IP400 External Expansion Modules
· Analog.
· Digital Station V1.
· Phone V1.
BS1363
Czech Republic, 700213374
Ireland, United
Kingdom.
NEMA1-15
North, Central
and South
America.
700213390
Korea.
700254519
IP400 External Expansion Modules
· Digital Station V2.
· Phone V2.
IP500 External Expansion Modules
· BRI So8.
· Digital Station 16/30.
· Phone 16/30.
IP500 External Expansion Modules
· Analog Trunk 16.
*Older units were supplied with a 40W unearthed PSU and required an IEC60320 C7 power cord.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 20
15-601042 Issue 23f (20 April 2011)
System Overview: Power Supplies and Cables
1.5.3 Power Supply Backup
The use of an Uninterrupted Power Supply (UPS) with any telephone system is strongly recommended. Even at sites that
rarely lose electrical power, that power may occasionally have to be switched off for maintenance of other equipment. In
addition, most UPSs also provide an element of power conditioning, reducing spikes and surges.
The capacity of UPS systems and the total equipment load the UPS is expected to support are usually quoted in VA. Where
equipment load is quoted in Watts, multiply by 1.4 to get the VA load.
The calculation of how much UPS capacity is required depends on several choices.
· What equipment to place on the UPS?
Remember to include server PCs such as the voicemail. It is recommended that the total load on a new UPS is
never greater than 75% capacity, thus allowing for future equipment.
· How many minutes of UPS support is required?
Actual UPS runtime is variable, it depends on what percentage of the UPSs capacity the total equipment load
represents. For example, a 1000VA capacity UPS may only support a 1000VA (100%) load for 5 minutes. This
relationship is not linear, the same UPS would support a 500VA (50%) load for 16 minutes. Therefore the lower the
percentage of capacity used, the increasingly longer the UPS runtime, typically up to 8 hours maximum. Remember
also that for most UPS's the ratio of discharge to full recharge time is 1:10.
· How many output sockets does the UPS provide?
Multiple UPS units may be required to ensure that every item of supported equipment has its own supply socket.
The web site http://www.avayaups.com provides a calculator into which you can enter the equipment you want supported
on a UPS. It will then display various UPS options. The site uses VA values for typical IP Office systems. However, if more
specific values are required for a particular system, the table below can be used to enter values.
Typical IP Office System
VA
Typical IP Office System
VA
IP500v2 System
230
Individual Equipment
VA
Individual Equipment
VA
Analog 16 Module
88
Phone 30 Module
42
Digital Station 16 Module
34
Typical Server PC
600
Digital Station 30 Module
42
Typical Desktop PC
400
Phone 8 Module
17
Mid Span PSU - 6 ports
150
Phone 16 Module
23
Mid Span PSU - 12/24 ports
300
· The 1151D2 power supply unit for Avaya H.323 IP phones includes a backup battery. This typically provides 15 minutes
backup at maximum load (20 Watts) and up to 8 hours at light load (2 Watts).
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 21
15-601042 Issue 23f (20 April 2011)
1.5.4 Cabling and Cables
The IP Office systems are designed primarily for use within an RJ45 structured cabling system using CAT3 unshielded
twisted-pair (UTP) cabling and RJ45 sockets.
A structured cabling system is one where cables are run from a central RJ45 patch panel in the communications/data room
to individual RJ45 sockets at user locations. All wires in each cable between the patch panel and the desk socket are
connected straight through. This arrangement allows devices connected at the patch panel to be swapped to match the
type of device that needs to be connected at the user socket. For example, making one user socket a phone port and
another user socket a computer LAN port, without requiring any rewiring of the cables between the patch panel and the
user location.
· Traditional IDC Punchdown Wiring Installations
Where necessary, the far end RJ45 plug can be stripped from IP Office cables and wired into traditional wiring
systems using punch-block connectors. This type of installation should be performed by an experienced wiring
technician.
· Trunk Connections
The majority of IP Office trunk ports use RJ45 connectors for acceptance of an RJ45-to-RJ45 cable. However,
connection at the line provider's end may require use of a different plug type in order to match the line providers
equipment.
· RJ11 Phone Connectors
Many phones use RJ11 sockets and are supplied with RJ11-to-RJ11 cables. RJ11 plugs can be inserted into RJ45
sockets and in many case the connection will work. However this is not recommended or supported as the
connection lock is not truly positive and may become disconnected. An RJ45-to-RJ11 cable 193 is available for these
connections.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 22
15-601042 Issue 23f (20 April 2011)
System Overview: Power Supplies and Cables
Standard IP Office Cables
The following are Avaya standard cables available for use with IP Office systems. The maximum length is applicable if the
standard Avaya cable is replaced with an alternate cable.
Cable
9-Way DTE Cable
107
Description
SAP Code
Standard
Length
Maximum
Length
Connects to control unit RS232 DTE port. 9Way D-type plug to 9-way D-type socket.
–
2m/6'6''.
2m/6'6''.
Structured Cabling DS Line
Cable 193
Connects from RJ45 sockets to RJ11 socketed TT700047871 4m/13'2''.
DS and analog phones.
See table
below.
BRI/PRI Trunk Cable
Connects BRI/PRI trunk ports to the line
700213440
provider's network termination point. RJ45 to
RJ45. Red.
3m/9'10''.
–
Expansion Interconnect
Cable 195
Connects the control unit to expansion
modules. RJ45 to RJ45. Blue.
700213457
1m/3'3''.
1m/3'3''.
LAN Cable
Connects from IP Office LAN ports to IP
devices. RJ45 to RJ45. Grey.
700213481
3m/9'10''.
100m/328'.
196
192
The table below details the maximum total cable distances for DS and analog extensions using different cable types.
Unshielded Twisted-Pair (UTP) - 50nf/Km
Telephone
CW1308
AWG22
(0.65mm)
AWG24
(0.5mm)
AWG26
(0.4mm)
1400 Series
1200m/3937'.
1000m/3280'.
670m/2200'.
400m/1310'.
9400/9500 Series
1200m/3937'.
1000m/3280'.
670m/2200'.
400m/1310'.
TCM (without power
booster)
–
305m/1000'
–
–
" (with power
booster)
–
790m/2600'
–
–
Analog Phones
1000m/3280'.
1000m/ 3280'.
400m/1640'.
800m/2620'.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 23
15-601042 Issue 23f (20 April 2011)
1.5.5 Grounding
All IP Office control units and external expansion modules must be connected to a functional ground. Where the unit is
connected to a power outlet using a power cord with an earth lead, the power outlet must be connected to a protective
earth.
Use of ground connections reduces the likelihood of problems in most telephony and data systems. This is especially
important in buildings where multiple items of equipment are interconnected using long cable runs, for example phone and
data networks.
In some cases, such as ground start trunks, in addition to being a protective measure, this is a functional requirement for
the equipment to operate. In other cases it may be a locale regulatory requirement and or a necessary protective step, for
example areas of high lightning risk.
·
WARNING
During installation do not assume that ground points are correctly connected to ground. Test ground points before
relying on them to ground connected equipment.
or
symbol. Ground
The ground point on IP Office control units and external expansion modules are marked with a
connections to these points should use a 14 AWG solid wire with either a green sleeve for a functional ground or green and
yellow sleeve for a protective ground.
· Additional protective equipment
In addition to grounding, additional protective equipment will be required in the following situations. Refer to "Out
of Building Telephone Installations 25 ".
· On any Digital Station or Phones external expansion module connected to an extension located in another
building.
· In the Republic of South Africa, on all Analog Trunk external expansion modules (ATM16) and on any control
units containing an analog trunk cards (ATM4/ATM4U).
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 24
15-601042 Issue 23f (20 April 2011)
System Overview: Power Supplies and Cables
1.5.6 Lightning Protection/Out-of-Building Connections
The following are the only supported scenarios in which wired extensions and devices outside the main building can be
connected to the IP Office system. In these scenarios, additional protection, in the form of protective grounding and surge
protectors, must be fitted.
·
WARNING
The fitting of additional protection does not remove the risk of damage. It merely reduces the chances of damage.
· Cables of different types, for example trunk lines, phone extensions, ground and power connections, should be kept
separate.
· All cabling between buildings should be enclosed in grounded ducting. Ideally this ducting should be buried.
· A Primary Protection Box must be provided at the point where the cables enter the building. This should be three
point protection (tip, ring and ground). Typically this would be gas tube protection provided by the local telephone
company. The ground wire must be thick enough to handle all the lines being affected by indirect strike at the same
time.
Connection Type
Protection Device Type
Requirement
Analog Phone Extensions
Phones External expansion
module (POT 198 or PHONE 198 )
ports only.
IP Office Barrier Box 103
· Connection from the expansion module to the
Supports a single connection.
phone must be via a surge protector at each end
Maximum of 16 on any expansion
and via the primary protection point in each
module.
building.
DS Phone Extensions
ITWLinx towerMAX DS/2 102
External expansion module DS Supports up to 4 connections.
193 ports only.
(This device was previously
referred to as the Avaya 146E).
TCM Phone Extensions
None
Analog Trunks
ITWLinx towerMAX CO/4x4
ITWLinx towerMAX SCL/8
(This device was previously
referred to as the Avaya 146G)
· The between building connection must be via
earthed ducting, preferable underground. The cable
must not be exposed externally at any point.
Currently not supported.
102
Supports up to 4 two-wire lines.
(This device was previously
referred to as the Avaya 146C).
External Output Switch
· The IP Office expansion module and control unit
and IROB devices must be connected to the
protective ground point in their building.
For installations in the Republic of South Africa, the
fitting of surge protection on analog trunks is a
requirement.
For other locations where the risk of lightning strikes
is felt to be high, additional protection of incoming
analog trunks is recommended.
Connections from an IP Office Ext O/P port to an
external relay device must be via a surge protector.
The towerMAX range of devices are supplied by ITWLinx (http://www.itwlinx.com).
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 25
15-601042 Issue 23f (20 April 2011)
1.6 Wall and Rack Mounting
All the IP Office control units are designed to be free-standing. On systems with external expansion modules, the control
unit and modules are intended to be stacked.
Using additional option mounting kits, some systems can be wall or rack mounted.
Control/Expansion Unit
Wall Mount
Rack
Mount
IP500 Control Unit
IP500v2 Control Unit
IP500 External Expansion Modules
IP400 External Expansion Modules
–
Wall Mounting
IP500, IP500v2 control units and IP500 external expansion modules can be wall mounted. To do this, a wall mounting kit
is required in addition to suitable wall fixings. Wall mounting is not supported for IP400 external expansion modules.
In addition to the existing environmental requirements
apply when wall mounting a unit:
38
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
The following wall mounting kits exist.
· IP500 Wall Mounting Kit V2 (SAP Code 700500923)
This kit can be used for wall mounting an IP500 or IP500 v2 control unit and IP500 external expansion modules.
This kit incorporates cable routing at the front and rear of the unit. For control units it allows orientation of the
control unit base card slots to the left or to the right.
· IP500 Wall Mounting Kit (SAP Code 700430150)
This old design of wall mounting kit can be used for wall mounting an IP500 or IP500v2 control units only. It does
not provide any cable routing and requires the control unit to be mounted with the base card slots to the right
only.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 26
15-601042 Issue 23f (20 April 2011)
System Overview: Wall and Rack Mounting
Rack Mounting
All IP Office control units and external expansion modules can be rack mounted into standard 19" rack systems. Each unit
requires a 2U slot space within the rack. Rack mounting requires an IP400 or IP500 rack mounting kit for each control unit
and external expansion module.
Where IP Office systems are being rack mounted, the effect of conditions within the rack cabinet must be considered. For
example the rack temperature may be above the room temperature and airflow within the rack will be restricted. The
environmental requirements 38 for the individual IP Office units are still applicable inside the rack cabinet.
IP500 Rack Mounting Kit
· IP500 Rack Mounting Kit (SAP 700429202)
This kit contains all the components required for the rack mounting of
a single IP500v2 control unit, IP500 control unit or IP500 external
expansion module. This includes screws for fixing of the brackets to
the module, bolts for securing the module in the rack and cable tidy
brackets.
IP400 Rack Mounting Kit
· IP400 Rack Mounting Kit (SAP 700210800)
This kit contains all the components required for the rack mounting of
a single control unit or expansion module. This includes screws for
fixing of the brackets to the module and bolts for securing the module
in the rack.
Barrier Box Rack Mounting Kit
· Barrier Box Rack Mounting Kit (SAP 700293905)
Barrier boxes must be used for out-of-building analog phone
extensions 25 . This bracket allows up to 8 IP Office barrier boxes to
be rack mounted and simplifies the number of connections to the
protective ground point in the rack. This kit must be used when more
than 3 barrier boxes are in use and supports a maximum of 16
barrier boxes for a single external expansion module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 27
15-601042 Issue 23f (20 April 2011)
1.7 Feature Keys and Licenses
A feature key is required for licensed features.
· IP500v2 Avaya SD Card 156
Inserts into the System slot on the rear of an IP500v2 control unit. This card is required even if not
using any IP Office licenses.
Various IP Office features and applications require entry of license keys into the system's configuration. The license keys
are unique 32-character codes based on the feature being activated and the serial number of the feature key dongle 156
installed with the IP Office system.
The serial number is printed on the feature key dongle and prefixed with FK. It can also be viewed in the system
configuration using IP Office Manager.
· For IP500v2 systems, the feature key dongle takes the form of an SD card inserted into the control unit. The card is
a mandatory item for these systems even if they use no licensed features.
When a license key is entered into the IP Office configuration, the following information is shown.
· Status
The status, which is Unknown until the configuration file is sent back to the IP Office system.
· Unknown
This status is shown for licenses that have just been added to the configuration shown in IP Office Manager.
Once the configuration has been sent back to the IP Office and then reloaded, the status will change to one of
those below.
· Valid
The features licensed can be configured and used.
· Invalid
The license was not recognized. It did not match the serial number of the Feature Key.
· Dormant
The license is valid but is conditional on some other pre-requisite licenses.
· Obsolete
The license is valid but is one no longer used by the level of software running on the IP Office system.
· Expired
The license has gone past its expiry date.
· License
The name of the licensed feature. This may differ from the ordered RFA name.
· Instances
Depending on the license, this may be the number of ports enabled or number of simultaneous users of the
licensed feature. Sometime the number of instances is specified in the license name.
· Expires
Most purchased licenses have no expiry setting. For some features, trial licenses may be available which will have
an expiry date.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 28
15-601042 Issue 23f (20 April 2011)
System Overview: Feature Keys and Licenses
1.8 IP Office Phones
IP Office Release 7.0 supports the following phones and phone add-ons. Availability may depend on location and may be
subject to local restrictions.
Digital Station (DS Port)
These digital stations connect to the IP Office via DS
Norstar Version mode.
· 1400 Series: 1403
· 9400 Series: 9404
· 9500 Series: 9504
161 ,
162 ,
164 ,
1408
9408
165 , 9508
164
1416
193
ports. The following are supported in IP Office Essential Edition -
163
165
Digital Station (TCM Port)
These digital stations connect to the IP500v2 IP Office system via TCM
Essential Edition - Norstar Version mode.
201
ports. The following are supported in IP Office
· 4100 Series: 4135, 4136, 4145, 4145EX, 4146, 4146EX - Connection to IP Office TCM ports via a Digital Mobility
Solution 180 system.
· 7400 Series: 7420, 7430, 7434, 7439, 7440, 7444, 7449 - Connection to IP Office TCM ports via a Digital Mobility
Solution 180 system.
· ACU: Audio Conferencing Unit 166
· M-Series: MT7100 167 , MT7100N 167 , MT7208 168 , MT7208N 168 , M7310 169 , M7310N 169 , M7324 170 , M7324N 170
.
· T-Series: T7000 171 , T7100 171 , T7208 172 , T7316 173 , T7316E 174 , T7406 175 , T7406E 175
Analog Telephones
Analog phones and devices connect to PHONE 198 ports with the IP Office system. However due to the variety of analog
phones and device available no guarantee of operation is given. It is the responsibility of the IP Office installer and
maintainer to test and verify the operation of proposed analog equipment.
· 6200 Series: 6211, 6219, 6221 (North America).
· Interquartz Gemini: 9330-AV, 9335-AV, 9281-AV (Europe, Middle East, Africa, Asia-Pacific).
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 29
15-601042 Issue 23f (20 April 2011)
1.9 SIP Trunks
The IP Office Essential Edition - Norstar Version mode can support SIP trunks through its LAN connection. These are
configured using IP Office Manager, they cannot be managed through phone based administration.
In order to support SIP trunks, the system must include the following resources:
· SIP Trunk Licenses
These licenses are used to configure the number of simultaneous SIP trunk calls supported, up to a maximum of
20. A IP Office Essential Edition - Norstar Version mode system supports 3 channels without licenses.
· Voice Compression Channels
These are required to convert between the audio compression methods used for IP telephony and those used for
analog and digital trunks. Each IP500 Combination card, up to a maximum of 2 cards, installed in the system
provides 10 voice compression channels for the system. One voice compression channel is used for each SIP call.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 30
15-601042 Issue 23f (20 April 2011)
System Overview: SIP Trunks
1.10 Supported Country Locales
When a new or defaulted system's configuration is first opened in Manager, the value set in the Locale field should always
be checked and changed if necessary. The system's Locale sets factors such as the default ringing patterns and caller
display settings. The locale also controls the language that a voicemail server will use for prompts.
· Argentina
· France
· Netherlands
· South Africa
· Australia
· Germany
· New Zealand
· Spain
· Bahrain
· Greece
· Norway
· Sweden
· Belgium
· Hong Kong
· Oman
· Switzerland
· Brazil
· Hungary
· Pakistan
· Taiwan
· Canada
· Iceland
· Peru
· Turkey
· Chile
· India
· Poland
· United Arab Emirates
· China
· Italy
· Portugal
· United Kingdom
· Colombia
· Korea
· Qatar
· United States
· Denmark
· Kuwait
· Russia
· Venezuela
· Egypt
· Mexico
· Saudi Arabia
· Finland
· Morocco
· Singapore
The locales supported in IP Office Essential Edition - Norstar Version mode are:
· Bahrain
· Morocco
· Qatar
· Turkey
· Egypt
· Oman
· Saudi Arabia
· United Arab Emirates.
· Kuwait
· Pakistan
· South Africa
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 31
15-601042 Issue 23f (20 April 2011)
1.11 IP Office Software Applications
The IP Office applications are available on a number of DVDs. These can be ordered at a nominal cost to cover order
processing and delivery. Separate installation packages for IP Office applications can also be downloaded from the Avaya
support website at http://support.avaya.com.
Title
IP Office Release 7.0 Admin and
User DVD Set
Discs Description
2
SAP Code
These DVDs contain installation packages for all the main IP
Office administration and user applications. They also contain
documentation for IP Office.
700500928
· DVD 1: Contains the IP Office Administrator
Applications suite, IP Office Documentation, IP Office
User Applications, IP Office Voicemail Pro.
· DVD 2: Contains the Customer Call Reporter,
ContactStore for IP Office and one-X Portal for IP
Office applications.
It is acceptable to make copies of the Avaya IP Office DVDs listed above. However the content must remain intact,
unaltered and without change or addition. Avaya does not accept any liability and responsibility for damage or
problems arising from the use of such copies.
Programming Applications
The following applications are used to program and maintain an IP Office system. Typically they run on a PC connected to
the IP Office system via its LAN interface. These applications are all provided on the IP Office Administrator Applications
DVD and don't require any licenses.
Due to the nature of the applications, if installed on a PC at the customer site, this should be a secure PC or the PC of a
trusted user. If a voicemail server PC is also being installed with the IP Office system, the same PC can be used for the
programming and maintenance applications.
For maintainers, these applications can also be run remotely if a route for data connections to the customer's IP Office
exists from the maintainer's location.
· IP Office Manager 181
This tool is used to access all parts of the IP Office configuration. Different levels of access can be defined to control
which parts of the configuration the Manager user can view and alter. Manager is also used to upgrade the software
files used by an IP Office system.
· System Status Application 183
This application can be used to inspect the current status of IP Office lines and extensions and to view records of
recent alarms and events. It runs as a Java application.
· Monitor (SysMon) 182
Monitor is a tool that can show a trace of all activity on the IP Office system in detail. As a consequence,
interpretation of Monitor traces requires a high-level of data and telephony protocol knowledge. Despite that
however, all IP Office installers and maintainers need to understand how to run Monitor when necessary as Avaya
may request copies of Monitor traces to resolve support issues.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 32
15-601042 Issue 23f (20 April 2011)
System Overview: IP Office Software Applications
User Applications
For systems running in IP Office Essential Edition - Norstar Version mode, the following is supported:
· TAPILink Lite 184
The Microsoft Telephony Application Program Interface (TAPI) allows TAPI compliant applications to interact with IP
Office phones by installing an IP Office TAPI driver. TAPILink Lite does not require any licenses entered into the IP
Office system's configuration. It allows TAPI compliant applications such as Outlook to make and answer calls. The
speech part of the calls is still via the user's physical phone.
Voicemail Applications
The IP Office supports a range of applications for the recording and playing of voicemail messages.
· Embedded Voicemail
This application is supported on all IP Office Release 6 systems. Embedded Voicemail supports basic voicemail
mailbox operation, simple auto-attendants and hunt group announcements. For IP500 and IP500v2 controls units,
embedded voicemail is provided by the Avaya SD card fitted by default.
Call Logging Applications
A wide range of 3rd -party applications exist to provide call logging and accounting for telephone systems. To support
these the IP Office provides an SMDR output.
· SMDR Output
For IP Office Release 5.0 and higher, the IP Office control unit directly output SMDR records to a specified IP
address.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 33
15-601042 Issue 23f (20 April 2011)
1.12 Training
Avaya University provides a wide range of training courses for IP Office and its associated applications. This includes
courses necessary for IP Office resellers to become Avaya Authorized Channel Partners and for individuals to achieve IP
Office certification.
Details of courses can be found on the Avaya University web site (http://www.avaya-learning.com). The site can be used
to check course availability and to book course. It also includes on-line courses and on-line course assessments. The site
requires users to setup a user name and password in order to track their personal training record.
1.13 Web Sites
Information to support the IP Office can be found on a number of web sites.
· Avaya (http://www.avaya.com)
The official web site for Avaya. The front page also provides access to individual Avaya web sites for different
countries.
· Avaya Enterprise Portal (http://partner.avaya.com)
This is the official web site for all Avaya Business Partners. The site requires registration for a user name and
password. Once accessed, the site portal can be individually customized for what products and information types
you wish to see and to be notified about by email.
· Avaya Support (http://support.avaya.com)
Contains documentation and other support materials for Avaya products including IP Office. Copies of the IP Office
CD images are available from this site and updated core software .bin files.
· Avaya IP Office Knowledge Base (http://marketingtools.avaya.com/knowledgebase)
Access to an on-line regularly updated version of the IP Office Knowledge Base.
· Avaya University (http://www.avaya-learning.com)
This site provides access to the full range of Avaya training courses. That includes both on-line courses, course
assessments and access to details of classroom based courses. The site requires users to register in order to
provide the user with access to details of their training record.
· Avaya Community (http://www.aucommunity.com)
This is the official discussion forum for Avaya product users. However it does not include any separate area for
discussion of IP Office issues.
· Other Non-Avaya Web Sites
A number of third-party web forums exist that discuss IP Office. These can act as useful source of information
about how the IP Office is used. Some of these forums require you to be a member and to register. These are not
official Avaya forums and their content is not monitored or sanctioned by Avaya.
· Tek-Tips (http://www.tek-tips.com)
· IP Office Info (http://www.ipofficeinfo.com)
· Yahoo Groups (http://groups.yahoo.com/group/ipoffice)
· PBX Tech (http://www.pbxtech.info/forumdisplay.php?f=8)
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 34
15-601042 Issue 23f (20 April 2011)
System Overview: Web Sites
1.14 Emergency and Power Failure Ports
IP Office systems can provide 2 types of analog extension power failure ports. These are:
Type
Description
Provided By:
Switching Power
Failure Ports
During normal IP Office operation these ports
can be used for normal analog phone
connection.
· IP500 Analog Phone 8 Card
When an IP500 Analog Phone 8 base card is
fitted with an IP500 Analog Trunk daughter
card, during power failure extension port 8 is
connected to analog trunk port 12.
During power failure the port is directly
connected to an analog trunk port.
· IP500 ATM Combination Card
On this card, during power failure, extension
port 8 is connected to analog trunk port 12.
Emergency Only Power During normal IP Office operation these ports
Failure Ports
cannot be used.
During power failure the port is directly
connected to an analog trunk port.
· IP500 Analog Trunk Daughter Card
Regardless of the IP500 card hosting it,
during power failure pins 4 and 5 of port 12
are connected to pins 7 and 8.
· IP400 ATM16 External Expansion
Module
This external expansion module has two
ports, PF1 and PF2, on its rear. During
power fail conditions, PF1 is internally
connected to ANALOG port 1 on the module,
PF2 is internally connected to ANALOG port
2 on the same module.
In all cases these only work with loop-start analog trunks. Any phones connected to these ports should be clearly labeled
as power fail extensions in accordance with the appropriate national and local regulatory requirements.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 35
15-601042 Issue 23f (20 April 2011)
Chapter 2.
Installation Requirements
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 37
15-601042 Issue 23f (20 April 2011)
2. Installation Requirements
2.1 Environmental Requirements
The planned location must meet the following requirements. If being installed into a rack system, these are requirements
for within the rack:
1. o Temperature: 0°C to 40°C / 32°F to 104°F.
2. o Humidity: 10% to 95% non-condensing.
3. o Check there are no flammable materials in the area.
4. o Check there is no possibility of flooding.
5. o Check that no other machinery or equipment needs to be moved first.
6. o Check that it is not an excessively dusty atmosphere.
7. o Check that the area is unlikely to suffer rapid changes in temperature and humidity.
8. o Check for the proximity of strong magnetic fields, sources of radio frequency and other electrical interference.
9. o Check there are no corrosive chemicals or gasses.
10.o Check there is no excessive vibration or potential of excessive vibration, especially of any mounting surface.
11.o Check that where telephones are installed in another building, that the appropriate protectors and protective
grounds are fitted (see Out of Building Telephone Installation 25 ).
12.o Check there is suitable lighting for installation, system programming and future maintenance.
13.o Check that there is sufficient working space for installation and future maintenance.
14.o Ensure that likely activities near the system will not cause any problems, e.g. access to and maintenance of any
other equipment in the area.
15.o Where ventilation holes are present on any of the IP Office units, those holes should not be covered or blocked.
16.o The surface must be flat horizontal for free-standing or rack mounted installations.
Wall Mounting
In additional to the requirements above, the following are applicable to IP Office units that support wall mounting.
1. Units must only be mounted onto permanent wall surfaces.
2. The surface must be vertical and flat.
3. Orientation of the unit must be as shown in the section on IP500 Wall Mounting
65
.
4. The appropriate Avaya wall mounting kits must be used.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the following:
1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of
electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 38
15-601042 Issue 23f (20 April 2011)
Installation Requirements: Environmental Requirements
2.2 Space Requirements
IP Office control units and modules are designed to be installed either in a free-standing stack or into a 19" rack system.
Rack installation requires a rack mounting kit 26 for each control unit and expansion module.
· Cable Clearance
Clearance must be provided at the front and rear of all modules for cable access and feature key dongle connection.
· On IP400 systems, allow a minimum clearance of 75mm (3 inches).
· On IP500 and IP500v2 systems allow a minimum clearance of 90mm (3.5 inches).
· Additional Clearance
Care should be taken to ensure that the positioning of the modules does not interrupt air flow and other factors that
may affect environmental requirements 38 . This is especially important on IP500 and IP500v2 control units which
have ventilation slots at the side.
· Cable Access
Power cords must not be attached to the building surface or run through walls, ceilings, floors and similar openings.
Installation measures must be taken to prevent physical damage to the power supply cord, including proper routing
of the power supply cord and provision of a socket outlet near the fixed equipment or positioning of the equipment
near a socket outlet.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 39
15-601042 Issue 23f (20 April 2011)
2.2.1 IP500 and IP500v2 Control Units
The ventilation slots on the rear and sides should not be covered or blocked.
2.2.2 External Expansion Modules
The dimensions below are applicable to all IP Office external expansion modules.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 40
15-601042 Issue 23f (20 April 2011)
Installation Requirements: Space Requirements
2.2.3 Wall Mounting
IP500, IP500v2 control units and IP500 external expansion modules can be wall mounted. To do this, a wall mounting kit
is required in addition to suitable wall fixings. Wall mounting is not supported for IP400 external expansion modules.
In addition to the existing environmental requirements
apply when wall mounting a unit:
38
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
The following wall mounting kits exist.
· IP500 Wall Mounting Kit V2 (SAP Code 700500923)
This kit can be used for wall mounting an IP500 or IP500 v2 control unit and IP500 external expansion modules.
This kit incorporates cable routing at the front and rear of the unit. For control units it allows orientation of the
control unit base card slots to the left or to the right.
· IP500 Wall Mounting Kit (SAP Code 700430150)
This old design of wall mounting kit can be used for wall mounting an IP500 or IP500v2 control units only. It does
not provide any cable routing and requires the control unit to be mounted with the base card slots to the right
only.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 41
15-601042 Issue 23f (20 April 2011)
Wall Mounting Kit V2
Wall Mounting Kit V1
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 42
15-601042 Issue 23f (20 April 2011)
Installation Requirements: Space Requirements
2.2.4 Rack Space Requirements
All IP Office control units and external expansion modules can be rack mounted into standard 19" rack systems. Each unit
requires a 2U slot space within the rack. Rack mounting requires an IP400 or IP500 rack mounting kit for each control unit
and external expansion module.
Where IP Office systems are being rack mounted, the effect of conditions within the rack cabinet must be considered. For
example the rack temperature may be above the room temperature and airflow within the rack will be restricted. The
environmental requirements 38 for the individual IP Office units are still applicable inside the rack cabinet.
IP500 Rack Mounting Kit
· IP500 Rack Mounting Kit (SAP 700429202)
This kit contains all the components required for the rack mounting of
a single IP500v2 control unit, IP500 control unit or IP500 external
expansion module. This includes screws for fixing of the brackets to
the module, bolts for securing the module in the rack and cable tidy
brackets.
IP400 Rack Mounting Kit
· IP400 Rack Mounting Kit (SAP 700210800)
This kit contains all the components required for the rack mounting of
a single control unit or expansion module. This includes screws for
fixing of the brackets to the module and bolts for securing the module
in the rack.
Barrier Box Rack Mounting Kit
· Barrier Box Rack Mounting Kit (SAP 700293905)
Barrier boxes must be used for out-of-building analog phone
extensions 25 . This bracket allows up to 8 IP Office barrier boxes to
be rack mounted and simplifies the number of connections to the
protective ground point in the rack. This kit must be used when more
than 3 barrier boxes are in use and supports a maximum of 16
barrier boxes for a single external expansion module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 43
15-601042 Issue 23f (20 April 2011)
Chapter 3.
IP Office Administration
Software
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 45
15-601042 Issue 23f (20 April 2011)
3. IP Office Administration Software
In order to install an IP Office system you must be familiar with using the following IP Office applications. They must be
available on your installation PC.
·
Manager
IP Office Manager is used to access all parts of the IP Office configuration. Different levels of access can be defined
to control which parts of the configuration Manager user can view and alter. Manager is also used to upgrade the
software files used by an IP Office system.
·
System Status
The IP Office System Status application (SSA) is a reporting tool that provides a wide range of information about
the current status of an IP Office system. Its can report the available resources and components within the system
and details of calls in progress. Details of the number of alarms are recorded and the time date of the most recent
alarms. When required for diagnostics escalation, SSA is able to take a snap shot image of the IP Office system's
status including a copy of its current configuration. Use of SSA requires an IP Office service user name and
password that has been configured for System Status access in the IP Office's security settings.
·
Monitor
IP Office Monitor (also known as System Monitor) is a tool that can show all activity on the IP Office system in great
detail. As a consequence, interpretation of Monitor traces requires a high-level of data and telephony protocol
knowledge. However, all IP Office installers and maintainers must understand how to run Monitor when necessary
as Avaya may request copies of Monitor traces to resolve support issues.
· Phone Based Administration
For systems running in IP Office Essential Edition - Norstar Version mode, many features can be administered using
phone based administration from either of the first two extensions in the system.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 46
15-601042 Issue 23f (20 April 2011)
IP Office Administration Software:
3.1 Installing the Admin Applications
The IP Office Administration suite consists of a number of applications for IP Office installers and
maintainers.
· o System Monitor - Install
· o Manager - Install
· o System Status Application - Install
· o Call Status - Optional
This software is not supported with IP Office Release 7.0 systems. It is provided only for
the maintenance of older systems.
Requirements
· o IP Office Release 7.0 User/Admin DVD Set (2) (700500928)
Alternatively the IP Office Administrator Applications suite can be downloaded from Avaya's support website (
http://support.avaya.com).
· o Windows PC Requirements
This should meet the requirements of the administrator applications being installed. The specification below are the
minimum requirements for IP Office Manager. If other applications are to be installed on the PC then their individual
requirements should also be meet.
Requirement
Minimum
Recommended
Processor
600MHz Pentium or AMD Opteron, AMD
Athlon64, AMD Athlon XP.
800MHz Pentium or AMD Opteron, AMD
Athlon64, AMD Athlon XP.
RAM
128MB
256MB
HD Space
1GB - 800MB for .NET2, 200MB for Manager.
1.4GB - 800MB for .NET2, 600MB for the full
IP Office Admin suite.
Display
800 x 600 - 256 Colors
1024 x 768 - 16-bit High Color
Operating
System
Supported on Windows XP Pro, Windows Vista, Windows 7, Windows 2003 and Windows
2008.
· 32-bit and 64-bit versions are supported.
· Vista support is only on Business, Enterprise and Ultimate versions.
· Windows 7 support is only on Professional, Enterprise and Ultimate versions.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 47
15-601042 Issue 23f (20 April 2011)
Installing the IP Office Admin Applications
1. Using the Add or Remove Programs option in the Windows Control Panel, check that the PC does not already
have a version of the IP Office Admin suite installed.
· If 'yes' and the suite is a pre-IP Office 3.2 version, remove the existing IP Office Admin suite via Add/Remove
Programs.
· If the existing suite is IP Office 3.2 or higher, it is possible to upgrade without removing the previous
installation. However, if the system already has a USB Feature Key, the key should be removed prior to
upgrading and then reinserted and the PC restarted.
2. Insert the IP Office Administrator Applications DVD. Select the option for the IP Office Administration Suit. A folder
window will display the installation files for the administration suite.
3. Double-click on setup.exe.
4. Select the language you want to use for the installation process. This does not affect the language used by Manager
when running. Click Next >.
5. Select who should be able to run the Admin Suite applications. Click Next >.
6. If required select the destination to which the applications should be installed. We recommend that you accept the
default destination. Click Next >.
7. The next screen is used to select which applications in the suite should be installed. Clicking on each will display a
description of the application. Click on the
next to each application to change the installation selection. When you
have selected the installations required, click Next >.
8. Ensure that at minimum System Monitor and Manager are selected. Click Next >.
9. Click Install.
10.Installation of Windows .Net2 components may be required. If dialogs for this appear, follow the prompts to
install .Net.
11.If requested, reboot the PC.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 48
15-601042 Issue 23f (20 April 2011)
IP Office Administration Software: Installing the Admin Applications
3.2 Installer PC Connection
During installation it is recommended that the IP Office control unit is started
without it being connected to any network. That ensure that the IP Office
defaults to a known set of IP address settings.
If the IP Office is started connected to a network with a DHCP server. The
programming PC will need to be connected to the same network as either a
DHCP client or with an IP address valid for that network.
This section covers connecting your installation PC directly to the IP Office
control unit.
Requirements
· o IP Office Administration PC
A Windows PC with the IP Office Administrator Application suite installed
47 .
· o LAN Cable
Direct Connection to a Defaulted IP Office Control Unit
1. The default address for an IP Office control unit LAN port is 192.168.42.1/255.255.255.0. To directly connect a PC,
change the TCP/IP properties for the PCs LAN port to the following:
Fixed IP address
192.168.42.203
Subnet mask
255.255.255.0
Default gateway
192.168.42.1.
· While setting the PC to be a DHCP client could be used, this is not recommended for performing more
advanced functions such as firmware upgrades.
2. Connect the LAN cable from the PCs LAN port the LAN or LAN1 port on the IP Office control unit.
3. Check that the orange LED lamp on the IP Office LAN port is on. The green LED may also be flickering as it indicates
traffic across the LAN connection.
4. To test the connection before running Manager or System Status Application:
· Select Start | Run and enter cmd.
· In the command window that appears enter ping 192.168.42.1. The results should show a number of ping
replies from the IP Office. This confirms basic communication between the Manager PC and the IP Office.
· If there are no ping replies enter ipconfig. The results should list the IP address settings of the Manager PC as
required above. If they do enter exit and check the cable connection.
5. You can now start Manager
50
, System Status
51
or System Monitor
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
52
.
Page 49
15-601042 Issue 23f (20 April 2011)
3.3 Starting Manager
IP Office Manager is used to access all parts of the IP Office configuration.
Manager can also be used to upgrade the software files used by an IP Office
system.
Requirements
· o IP Office Administration PC
A Windows PC with the IP Office Administrator Application suite installed
47 .
· o LAN Cable
1. Select Start | Programs | IP Office | Manager.
2. If the PC has firewall software installed, you may be prompted as to whether you want to allow this program to
access the network. Select Yes or OK.
3. Select File | Open Configuration from the menu bar.
4. The Select IP Office window appears. After a few seconds it should list the IP Office control unit. The default name
used for a newly installed IP Office control unit is its MAC address.
· If the system required was not found, the address used for the search can be changed. Enter or select the
required address in the Unit/Broadcast Address field and then click Refresh to perform a new search.
5. Click the check the box next to the system and then click OK.
6. The name and password request is displayed. The name and password must match one of those setup through the
security settings. For a IP Office Essential Edition - Norstar Version mode system, the default name and password
for configuration access are Administrator and password.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 50
15-601042 Issue 23f (20 April 2011)
IP Office Administration Software: Starting Manager
3.4 Starting System Status
The IP Office System Status application (SSA) is a reporting tool that provides a
wide range of information about the current status of an IP Office system. Its can
report the available resources and components within the system and details of
calls in progress. Details of the number of alarms are recorded and the time date
of the most recent alarms.
When required for diagnostics escalation, SSA is able to take a snap shot image of
the IP Office system's status including a copy of its current configuration. Use of
SSA requires an IP Office service user name and password that has been
configured for System Status access in the IP Office's security settings.
Requirements
· o IP Office Administration PC
A Windows PC with the IP Office Administrator Application suite installed
47 .
· o LAN Cable
1. There are several methods that can be used to start the IP Office System Status application.
· On a PC where System Status has been installed, select Start | Programs | IP Office | System Status.
· If Manager is also installed and is running, select File | Advanced | System Status.
· For IP500v2 controls units, start a web browse and enter the IP address of the control unit. Select the link for
the System Status Application.
2. Once System Status has started, it will request the details of the IP Office system to which you want it to connect.
· Control Unit IP Address
Enter the IP address of the IP Office control units LAN interface or use the drop down to select a previously
used address..
· Local IP Address
If the PC has more than one IP address assigned to its network card or multiple network cards, the address to
use can be selected if necessary.
· User Name/Password
Enter the same user name and password as used for IP Office Manager.
· Auto Reconnect
If selected, System Status will attempt to reconnect using the same settings if connection to the IP Office is
lost.
3. Enter the required details for the IP Office and click Logon.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 51
15-601042 Issue 23f (20 April 2011)
3.5 Starting Monitor
IP Office Monitor (also know as System Monitor) is a tool that can show all activity
on the IP Office system in great detail. As a consequence, interpretation of
Monitor traces requires a high-level of data and telephony protocol knowledge.
However, all IP Office installers and maintainers must understand how to run
Monitor when necessary as Avaya may request copies of Monitor traces to resolve
support issues.
Requirements
· o IP Office Administration PC
A Windows PC with the IP Office Administrator Application suite installed
47 .
· o LAN Cable
1. Select Start | Programs | IP Office | Monitor.
2. If System Monitor has been run before it will attempt to connect with the system which it monitored previously. If
otherwise or you want to monitor a different system use the steps below.
3. Select File | Select Unit.
4. Enter the IP Office IP address and password of the IP Office Control Unit you want to monitor.
· For an IP Office system, ensure that the Control Unit Type is set to IP Office.
5. Click OK.
3.6 Phone Based Administration
For systems running in IP Office Essential Edition - Norstar Version mode, many features can be administered using phone
based administration.
Some settings cannot be changed through phone based administration; for example IP address and SIP trunk settings.
Those settings are only used in conjunction with network systems for which it is assumed that IP Office Manager will be
used for system configuration.
Phone based administration is only possible using either of the first two extension in the system. The phone connected at
those positions also needs to be capable of being used for phone based admin.
· Supported phones are: M7310, M7310N, M7324, M7324N, T7316E, T7316, 1408 and 1416 phones.
· The card fitted into Slot 1 of the control unit must be the correct type to support the phones.
· For details, refer to the IP Office Essential Edition - Norstar Version Phone Based Administration manual.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 52
15-601042 Issue 23f (20 April 2011)
Chapter 4.
IP500v2 Installation
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 53
15-601042 Issue 23f (20 April 2011)
4. IP500v2 Installation
This installation process is a simple outline as installation requirements and processes will vary.
· In this process, all the IP Office hardware components are installed and connected without being switched on until
the end of the process. The control unit will then upgrade all the connected components, including phones, to the
appropriate level of firmware.
· Also when switched on, the system is not connected to the customers data network. This ensures that the control
unit will default to known default IP address settings (unless you have pre-loaded the System SD card with a
configuration file with different settings).
· Tools and Parts Required 55
Check that you have the tools and additional parts required.
· Documentation 56
Ensure that you have obtained and read all the relevant documentation.
· Unpacking 57
Check that all the required equipment has been delivered and that there is no damage.
· SD Card Preparation 58
Upgrade and pre-load the System SD card with a configuration and other files in order to speed up installation.
· Install the Base Cards 62
Attach any trunk daughter cards to the IP500 base cards. Insert the cards into the control unit.
· Wall Mounting 65
If wall mounting, attach the brackets and fit the unit to the wall.
· Rack Mounting 69
If rack mounting, attach the brackets and fit the control unit into the rack.
· Connect External Expansion Modules 71
Connect the external expansions modules to the control unit.
· Grounding 73
Attach required ground cables to the control unit and external expansion modules.
· LAN Network Connections 74
Attach the IP Office control unit and a PC with IP Office Manager to the LAN network.
· Starting the System 75
Insert the System SD card and power up the system.
· Connecting Phones 78
Connect the Avaya digital phones.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 54
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation:
4.1 Tools and Equipment Required
The following is a general summary of the tools required. Additional tools and equipment will be
required for wall and or rack mounting and to fashion ground cable connections suitable to local
requirements.
· Tools Required
· o 5mm Flat-blade screwdriver.
· o Crosshead screwdriver.
· o Anti-static wrist strap and ground point.
· o RJ45-RJ45 Ethernet LAN Cable.
· o M4 Cross-Head Screwdriver.
· o Tools suitable for crimping a cable spade.
· o If wall mounting, drills and tools for wall mounting fixtures.
· Additional Parts Required
In addition to orderable IP Office equipment, the following items will be required.
· o 14AWG Solid copper wire for ground connection of control units and expansion modules.
· o Cable sleeve matching local regulator requirements for ground wires. Typically green for a functional ground
and green/yellow for a protective ground.
· o If wall mounting, additional fixtures and fittings suitable for the wall type and mounting kit being used.
· o Cable ties and labels for tidying and identifying cables.
· PC Requirements
IP Office Essential Edition - PARTNER® VersionIP Office Essential Edition - Norstar VersionIP Office Essential Edition
- Quick Version
1. o Windows PC with IP Office Admin suite installed
47
and RJ45 Ethernet LAN port.
2. o SD Card reader.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 55
15-601042 Issue 23f (20 April 2011)
4.2 Documentation
Ensure that you have read this manual in full before starting installation. Also include the
installation documentation for any other equipment and applications being installed as part
of the IP Office system.
·
IP Office Technical Bulletins
Ensure that you have obtained and read the IP Office Technical Bulletin relating to the IP Office software release
which you are installing. This bulletin will contain important information that may not have been included in this
manual. IP Office Technical Bulletins are available from the Avaya support website (http://support.avaya.com).
·
Upgrade Licenses
Some upgrades may require entry of upgrade licenses.
· IP Office Product Description
Covers the features provided by IP Office 7.0 - IP Office Essential Edition - Norstar Version.
· IP Office Essential Edition - Norstar Version Installation Manual
Covers the equipment supported and the installation of that equipment.
· IP Office Essential Edition - Norstar Version Manager
Covers the system programming that can be performed using the IP Office Manager application.
· IP Office Essential Edition - Norstar Version Phone Based Administration Manual
Covers the range of system programming that can performed from the first two extensions in the system.
Information Web Sites
IP Office documentation is available from the following web sites.
· Avaya Support (http://support.avaya.com)
Contains documentation and other support materials for Avaya products including IP Office. Copies of the IP Office
CD images are available from this site and updated core software .bin files.
· Avaya IP Office Knowledge Base (http://marketingtools.avaya.com/knowledgebase)
Access to an on-line regularly updated version of the IP Office Knowledge Base.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 56
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation: Documentation
4.3 Unpacking
Use the following procedure when unpacking any equipment supplied by
Avaya or an Avaya reseller or distributor.
Information Required
· o Equipment Checklist.
An installation checklist of the parts and equipment ordered for the
installation.
Procedure
1. o Check for Packaging Damage
Before unpacking any equipment, check for any signs of damage that may have occurred during transit. If any
damage exists bring it to the attention of the carrier.
2. o Check the Correct Parts Have Been Delivered
Check all cartons against the packing slip and ensure that you have the correct items. Report any errors or
omissions to the equipment supplier.
3. o Retain All Packaging and Documentation
While unpacking the equipment, retain all the packaging material. Fault returns are accepted only if repackaged in
the original packaging. If performing a staged installation, the original packaging will also assist when repacking
equipment to be moved to the final install site.
4. o Ensure that Anti-Static Protection Measures are Observed
Ensure that anti-static protection measures are observed at all times when handling equipment with exposed
electrical circuit boards.
5. o Check All Parts
Visually inspect each item and check that all the necessary documentation and accessory items have been included.
Report any errors or omissions to the dealer who supplied the equipment.
6. o Check All Documentation
Ensure that you read and retain any documentation included with the equipment.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 57
15-601042 Issue 23f (20 April 2011)
4.4 SD Card Preparation
IP500v2 control units are supplied with no installed firmware or configuration. When first powered up, the control unit will
load and install the necessary firmware from the System SD card installed in it. It will then create a default configuration
matching the cards installed in the control unit and external expansion modules attached to it.
You can perform a number of additional actions prior to installing the System SD card in order to pre configure the IP
Office system.
· Upgrade the Card Firmware
· Add a Configuration File
· Add a License File
58
58
61
· Add Music on Hold Files
61
Additional actions that can be performed on SD cards are detailed in the SD Card Management
114
section.
4.4.1 Upgrade the Card Firmware
This command can be used with a read-writeable SD card on the Manager PC. It copies the files and folders used by an
IP500v2 system when starting. It updates the card with the version of those files installed with the IP Office Manager
application. It includes the binary files for the IP500v2 system, external expansion modules and phones. It also includes
the prompt files for embedded voicemail operation.
This process just replaces existing files and adds new files. It does not delete files, so for example, any existing embedded
voicemail messages and greetings are retained. If the card contains dynamic system files such as SMDR records, they are
temporarily backed up by Manager and then restored after the card is recreated.
For the card to be used in an IP500v2 system's System SD slot the card must be Avaya SD Feature Key card. The card
must be correctly formatted, however a reformat of an existing working card is not necessary before using recreate to
update the card contents.
· The source for the files copied to the SD card are the sub-folders of the \Memory Cards folder under Manager's
Working Directory (normally C:\Program Files Avaya\IP Office\Manager). However, if the Working Directory
is changed to a location without an appropriate set of \Memory Cards sub-folders, the required set of files will not
be copied onto the SD card.
1. Once started do not interrupt this process, for example by removing the SD card. This process takes approximately
15 minutes.
2. Insert the SD card into a card reader on the Manager PC.
3. Using IP Office Manager, select File | Advanced | Recreate IP Office SD Card.
4. Select IP Office A-Law, IP Office U-Law or IP Office Partner Version. This selection will affect how the IP
Office systems operates when defaulted with this card present in its System SD card slot. .
5. Browse to the card location and click OK.
6. Manager will start creating folders on the SD card and copying the required files into those folders. This process will
take approximately 15 minutes.
7. Do not remove the SD card during the process. Wait until the Manager displays a message.
4.4.2 Adding a Pre-Built Configuration File
IP Office Manager can be used to create an IP Office configuration file 60 . For IP500v2 control units, such a pre-created
IP Office configuration file can be placed on the System SD card. That file will then be used when the IP Office system is
started.
1. Using IP Office, create an offline configuration that matches the customer requirements and the equipment that will
be installed in the IP Office.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 58
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation: SD Card Preparation
2. Rename the configuration file config.cfg.
3. Using a card reader, copy the file into the /system/primary folder on the System SD memory card.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 59
15-601042 Issue 23f (20 April 2011)
4.4.3 Creating a Configuration File
IP Office Manager can be used to create a new configuration without connecting to an IP Office system. During the
process, you can specify the locale of the system, what type of trunk cards it uses and what type of control unit and
expansion modules to include.
This allows the creation of a configuration prior to installation of system. The configuration file can be placed onto the
System SD card 58 before it is installed into the system. Otherwise the configuration can be uploaded to the system using
Manager after initial installation of the system.
· The configuration created must match the physical equipment in the IP Office system onto which the configuration
will be loaded. Doing otherwise may cause the IP Office system to reset and experience other problems.
1. Start IP Office Manager with no configuration loaded into Manager
2. Click on Create an Offline Configuration in the simplified view.
3. Select the type of configuration that you want to create. The equipment and settings will be restricted to those
supported in the selected mode.
4. When completed click OK.
5. Manager will create an load the configuration.
6. Edit the configuration to match the customer requirements. This can include importing information from
preprepared CSV files.
7. When completed, select File | Save Configuration As.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 60
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation: SD Card Preparation
4.4.4 Adding a License File
For IP500v2 control units, if a licence file called keys.txt is found in the SD card folder which the IP Office uses when it
boots, the IP Office will merge the licenses in that file with its configuration.
The files should be a plain text file (UTF8) containing either:
· A license name and license key separated by a
comma on each line.
· A license key on each line.
Teleworker, [email protected]@VOzIgeegwLXL2sAs1Z5
Mobile Worker, NvWO_iVY5KJpZMNeY89IB1sIj0_QUCDm
Power User, 9IJQW3yuPsbxjGS2XcMa16_J9H8cSeZ9
System Advanced, [email protected]_1
[email protected]@VOzIgeegwLXL2sAs1Z5
NvWO_iVY5KJpZMNeY89IB1sIj0_QUCDm
9IJQW3yuPsbxjGS2XcMa16_J9H8cSeZ9
[email protected]_1
1. Using a card reader, copy the file into the /system/primary folder on the System SD memory card.
4.4.5 Adding Music on Hold Files
By default the IP Office will use internal music on hold by uploading a music file from the IP Office Manager PC. For
IP500v2 systems, you can load a file onto the System SD card prior to installing it in the IP Office.
The file must be of the following format and must be called holdmusic.wav.
Property
Value
File Type
WAV
Bit Rate
128kbps
Audio sample size
16 bit
Channels
1 (mono)
Audio Sample Rate
8 kHz
Audio Format
PCM
Length
Up to 90 seconds.
1. Rename the music file holdmusic.wav.
2. Using a card reader, copy the file into the /system/primary folder on the System SD memory card.
3. If the IP Office is or will be configured for additional hold music files (up to 3 additional files), copy those files to the
same location. The name of the additional files must match those specified in the IP Office system's configuration.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 61
15-601042 Issue 23f (20 April 2011)
4.5 IP500 Card Installation
The IP500 base cards and trunk daughter cards should be fitted before power
is applied to the control unit. Ensure that cards are inserted in the order that
matches the planned or pre-built configuration.
1. Fitting IP500 Trunk Daughter Cards to the Base Cards.
2. Installing IP500 Cards into the Control Unit.
·
63
64
Warnings
· Correct anti-static protection steps should be taken before handling circuit boards.
· Cards must never be added or removed from the control unit while it has power connected.
· General Notes
· Cards can be fitted in any order into any available slots.
· For phone based administration, the card in slot 1 must be able to support M7324, M7310, T7316E, T7316,
1408 or 1416 phones.
· It is recommended that cards are fitted from left to right.
· There are restrictions to the number of supported cards of some types. When such a limit is exceed, the rightmost card of that type will not function.
· Ensure that you use the labels supplied to identify the card fitted into the control unit.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 62
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation: IP500 Card Installation
4.5.1 IP500 Daughter Card Preparation
IP500 trunk daughter cards can be fitted to any IP500 base card. For IP500 Combination cards, the trunk daughter card is
pre-installed and cannot be changed.
Warnings
1. Correct anti-static protection steps should be taken while handling
circuit boards.
Parts and Equipment Required
1. o IP500 Base Card
2. o IP500 Trunk Daughter Card
3. o 3 Stand Off Pillars
These are supplied with the trunk daughter card.
Tools Required.
1. o 5mm Flat-blade screwdriver.
2. o Anti-static wrist strap and ground point.
Procedure: Installing a Trunk Daughter Card
1. Check that correct cards have been supplied.
2. Ensure that you are wearing an anti-static wrist strap connected
to a suitable ground point.
3. On the base card identify the position of 3 holes for the plastic
pillars for the IP500 card. These are along the same edge as the
card connector.
4. Fit the stand off pillars to the IP500 base card.
5. If there is a clip-on metal shield over the connector block on the
base card, remove it.
6. Using minimal force and checking that the pins are correctly
located, push the IP500 trunk card onto its connector block and
the stand off pillars.
7. Check that the card connector has snapped into position.
8. Using the washers and screws provided, secure the metal stand
off pillars to the base card.
9. A set of labels are supplied with the trunk daughter card. Fit the
appropriate label to the front of the base card.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 63
15-601042 Issue 23f (20 April 2011)
4.5.2 IP500 Card Insertion
Having prepared each IP500 base card by adding any trunk daughter card
control unit.
·
63
, the base card can be inserted into the
Warnings
· Correct anti-static protection steps should be taken while handling circuit boards.
· Cards must never be added or removed from the control unit while it has power connected.
· Tools Required
· o 5mm Flat-blade screwdriver.
· o Anti-static wrist strap and ground point.
Installing an IP500 Card
1. Check that there is no power to the control unit.
2. Using a flat-bladed screwdriver, remove the cover from the slot on the front of the control unit that will be used for
each card being installed. This cover is no longer required but should be retained until installation has been
completed.
3. Allowing the card to rest against the bottom of the slot, begin sliding it into the control unit. When half inserted,
check that the card rails have engaged with the slot edges by trying to gently rotate it. If the card rotates remove it
and begin inserting it again.
4. The card should slide in freely until almost fully inserted. At this point apply pressure at the base of the front of the
card to complete insertion.
5. Using a flat-bladed screwdriver secure the card.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 64
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation: IP500 Card Installation
4.6 Wall Mounting
IP500, IP500v2 control units and IP500 external expansion modules can be wall mounted. To do this, a wall mounting kit
is required in addition to suitable wall fixings. Wall mounting is not supported for IP400 external expansion modules.
In addition to the existing environmental requirements
apply when wall mounting a unit:
38
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
The following wall mounting kits exist.
· IP500 Wall Mounting Kit V2 (SAP Code 700500923)
This kit can be used for wall mounting an IP500 or IP500 v2 control unit and IP500 external expansion modules.
This kit incorporates cable routing at the front and rear of the unit. For control units it allows orientation of the
control unit base card slots to the left or to the right.
· IP500 Wall Mounting Kit (SAP Code 700430150)
This old design of wall mounting kit can be used for wall mounting an IP500 or IP500v2 control units only. It does
not provide any cable routing and requires the control unit to be mounted with the base card slots to the right
only.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 65
15-601042 Issue 23f (20 April 2011)
4.6.1 Wall Mounting Kit V2
These notes relate to the IP500 Wall Mounting Kit V2 (SAP 700500923). This kit can be used to wall mount IP500 and
IP500v2 control units and IP500 external expansion modules.
The kit includes all components necessary for wall mounting onto a plywood surface. The use of the cable covers is
optional.
In addition to the existing environmental requirements
apply when wall mounting a unit:
38
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
· The installation must be done by a service person only.
· For control units, the mesh flame screen must be installed in the bottom edge of the control unit before mounting.
· Ensure that the system has been shutdown and power has been removed from all the units. Shutdown the system
using a shutdown command and then remove power. Do not simply remove the power.
· If mounting a control unit, you must wait at least 15 minutes after removing the power cord before fitting the flame
screen.
· A suitable mounting surface of at least 19mm (0.75 inch) plywood is required.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 66
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation: Wall Mounting
Wall Mounting Process
Figure 1
1. Shutdown the System
Ensure that the system has been shutdown and power has been removed
from all the units.
· If mounting a control unit, you must wait at least 15 minutes after
removing the power cord before fitting the flame screen.
· Shutdown the system using a shutdown command and then remove
power. Do not simply remove the power.
Figure 2
2. Fit the Flame Screen: Mandatory - Control Units Only (See Figure 1)
·
! WARNING: The flame screen mesh must be fitted.
a. Remove the cards or blank slot covers from the left-hand and righthand slots.
b. Insert the flame screen into the bottom of the control unit, with the
two black plastic pegs at the front.
c. Press the two pegs through the air flow holes in the control unit
casing.
Figure 3
d. Check that the pegs have come through and have secured the flame
screen in place and that the screen is flush with the chassis.
3. Attach Brackets on One Side (See Figure 2)
On one side of the unit, attach one pair of the metal brackets.
· Only use the screws provided with the wall mounting kit for attaching
the metal brackets.
4. Attach the Cable Cover and Bracket (See Figure 3)
Use of the cable covers is optional. If not being used, simply attach the other
pair of brackets to the other side of the unit; otherwise:
Figure 4
a. Hook one of the cable covers into the leading hole of one of the metal
brackets.
b. Hook another bracket onto the other end of the cable cover and then
attach that bracket to the unit.
Figure 5
c. Repeat the process to attach the other cable cover to the unit.
5. Fit the Wall Bracket (See Figure 4)
Using 2 of the screws provided with the kit, attach the wall bracket to the
plywood surface.
Figure 6
6. Place the Unit onto the Wall Bracket (See Figure 5)
Lift the unit onto the wall bracket. The two metal brackets at the top of the
unit hook over the top of the wall bracket.
7. Attach the Unit to the Wall Panel (See Figure 6)
a. Using the remaining 4 screws provided with the kit, fix the cover
brackets to the plywood surface.
b. Reinsert the base cards and blank slot covers.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 67
15-601042 Issue 23f (20 April 2011)
4.6.2 Wall Mounting Kit V1
These notes relate to the older design of wall mounting kit (SAP 70043015) used
for IP500 and IP500v2 control units. This kit cannot be used for external expansion
modules.
The kit includes two brackets, one top and one bottom, and screws for attachment
to the control unit. Additional 4 x 4.5mm fixtures and fittings are required suitable
for the wall type.
In addition to the existing environmental requirements 38 for an IP Office system,
the following additional requirements apply when wall mounting a unit:
· The wall surface must be vertical, flat and vibration free. Attachment to
temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the
brackets to the control unit.
· The brackets must be used as shown, with the deeper tray-like bracket used
at the bottom of the wall mounted control unit.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 68
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation: Wall Mounting
4.7 Rack Mounting
The IP500 control unit and IP500 external expansion units can be
rack mounted if required into 19-inch rack systems. This requires
an IP500 Rack Mounting Kit (SAP 700429202) for each unit.
The kit includes:
· A rack mounting bracket and screws for attachment of the
bracket to the unit
· Nuts and bolts for rack attachment.
· Brackets and cable ties for cable tidying.
As indicated in the diagram following, the rack mounting bracket
can be used in several positions on the unit. IP400 external
expansion units used in an IP500 system can also be rack mounted
but use a separate IP400 Rack Mounting Kit.
Environmental Requirements
In addition to the existing environmental requirements
considered when rack mounting a unit:
38
for an IP Office system, the following additional factors must be
1. Rack Positioning - Ensure compliance with the rack manufacturers safety instructions. For example check that the
rack legs have been lowered and fixing brackets have been used to stop toppling.
2. Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given
to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified
by the manufacturer.
· o Operating Temperature: 0°C (32°F) to 40°C (104°F).
· o Operating Humidity: 10% to 95% non-condensing.
3. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for
safe operation of the equipment is not compromised. Proper ventilation must be maintained. The side ventilation
slots on the IP500 control unit should not be covered or blocked.
4. Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
5. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the
effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing this concern.
6. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should
be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
7.
Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 69
15-601042 Issue 23f (20 April 2011)
·
Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 70
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation: Rack Mounting
4.8 Connecting External Expansion Modules
Any external expansion modules should be connected to the control unit before
power is applied to the control unit. Ensure that modules are attached in the order
that matches the planned or pre-built configuration.
External expansion modules connect to the IP Office control unit using an
expansion interconnect cable. Each module is supplied with an expansion connect
cable and a power supply unit 19 . An appropriate locale specific power cord 20 for
the power supply unit must be ordered separately.
· Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This
cable must be used when connecting to expansion ports on the rear of a control unit.
Installation Requirements
· o Installation space either on or under the existing IP Office control unit.
· o Switched power outlet socket.
· o Available EXPANSION port on the control unit.
· o Grounding Requirements
· o Functional Grounding
Connection of a functional earth 24 is:
· o Recommend for all modules.
· o Connection of a functional ground is mandatory for Analog Trunk modules.
· o Protective Grounding
Connections of a protective ground via surge protection equipment 25 is:
· o Mandatory for Analog trunk modules in the Republic of South Africa.
· o Mandatory for Digital Station and Phone modules connected to out of building extensions.
· o Mandatory for Digital Station V2 and Phone V2 modules.
Tools Required
· o Manager PC.
· o Tools for rack mounting
69
(optional).
Parts and Equipment Required
· o External Expansion Module.
Each module is supplied with a suitable external power supply unit and a 1m blue interconnect cable. 2m Yellow
interconnect cables are supplied with the IP500 4-Port Expansion card and should only be used with that card.
· o Power cord for the power supply unit
· o Rack mounting kit
26
20
.
(optional).
· o Wall mounting kit - IP500 external expansion modules only (optional).
· o Cable labeling tags.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 71
15-601042 Issue 23f (20 April 2011)
Procedure
1. External expansion modules should not be attached to a control unit that has power.
2. If the IP Office system is being installed in a rack, attach the rack mounting kit
69
to the expansion module.
3. Attach the external expansion module's power supply but do not switch power on.
4. Connect the expansion interconnect cable from the module's EXPANSION port to the EXPANSION port on the control
unit. Make careful note of the port used and include this detail on the cable label and any other system records.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 72
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation: Connecting External Expansion Modules
4.9 Grounding
Use of ground connections reduces the likelihood of problems in most telephony and data systems. This is especially
important in buildings where multiple items of equipment are interconnected using long cable runs, for example phone and
data networks.
All IP Office control units and external expansion modules must be connected to a functional ground. Where the unit is
connected to a power outlet using a power cord with an earth lead, the power outlet must be connected to a protective
earth.
In some cases, such as ground start trunks, in addition to being a protective measure this is a functional requirement for
the equipment to operate. In other cases it may be a locale regulatory requirement and or a necessary protective step, for
example areas of high lightning risk.
·
WARNING
During installation do not assume that ground points are correctly connected to ground. Test ground points before
relying on them to ground connected equipment.
· Additional protective equipment
In addition to grounding, additional protective equipment will be required in the following situations.
· On any Digital Station or Phones external expansion module connected to an extension located in another
building. Refer to "Out of Building Telephone Installations 25 ".
· In the Republic of South Africa, on all Analog Trunk external expansion modules (ATM16) and on any control
units containing an analog trunk cards (ATM4/ATM4U).
Tools Required
· o M4 Cross-Head Screwdriver.
· o Tools suitable for crimping a cable spade.
Parts and Equipment Required
· o 14AWG Solid copper wire for ground connection.
· o Cable sleeve matching local regulator requirements. Typically green for a functional ground and green/yellow for
a protective ground.
The ground point on IP Office control units and expansion modules are marked with a
or
symbol. Ground
connections to these points should use a 14 AWG solid wire with either a green sleeve for a functional ground or green and
yellow sleeve for a protective ground.
IP500/IP500v2 Control Unit
On IP500 control units the ground point is located above the RS232 DTE port.
External Expansion Modules
On expansion modules, the ground point is a 4mm screw located towards the right on the rear of the module.
· On some older modules, the dedicated ground point screw is not present. In those cases, the top-center cover
fixing screw (3mm) can be used as an alternative ground connection point. A toothed washer should be added to
ensure good contact.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 73
15-601042 Issue 23f (20 April 2011)
4.10 Network Connection
The section below details how a new IP Office system determines what IP address it should use. Note that this only applies
for a new system loading IP Office Release 7.0 and higher.
IP Address and DHCP Mode Resolution
When a defaulted or new IP Office control unit is switched on, it requests IP address information from a DHCP Server on
the network. This operation will occur whether the LAN cable is plugged in or not. The process below is done separately for
both the LAN port (LAN1 in the configuration) and the WAN port (LAN2 in the configuration) on the back of the IP Office
control unit.
· The IP Office makes a DHCP request for what IP address information it should use.
· If a DHCP server responds within approximately 10 seconds, the control unit defaults to being a DHCP client and
uses the IP address information supplied by the DHCP server.
· If no DHCP Server responds, the control unit still defaults to being the DHCP client but assumes the following
default addresses:
· LAN1: 192.168.42.1/255.255.255.0.
· LAN2: 192.168.43.1/255.255.255.0.
· Note that the IP Office does not check that these addresses are valid and or available on the network.
·
! Once an IP500v2 control unit has obtained IP address and DHCP mode settings, it will retain those settings even
if rebooted without a configuration file present on the System SD card. To fully remove the existing IP address and
DHCP mode setting the IP Office must be defaulted using IP Office Manager.
PC Connection
Depending on the conditions that applied when the IP Office control unit was first started, a PC can be connected as
follows:
· If the IP Office is not connected to a network:
Connect the PC directly to the IP Office. It must be set to an address valid on the same network as the IP Office
defaults above.
· If the IP Office is connected to a network with no DHCP server:
Connect the PC directly to the IP Office. It must be set to an address valid on the same network as the IP Office
defaults above.
· If the IP Office is connected to a network with a DHCP server:
Connect the PC to the network. It must be set to be a DHCP client or to an address that is valid for the network.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 74
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation: Network Connection
4.11 Starting the System
1. With the IP500v2 control unit shut down or unpowered, insert the Avaya
System SD card into the System SD slot on the rear of the control unit.
· Ensure that you have the correct card.
· Ensure that the card has the level of software required. If necessary
the card can be upgraded to match a version of IP Office Manager
58 .
2. Apply power to the external expansion modules if any. The power outlet
used must include a switch and in cases where the power cord includes
an earth lead, that outlet must have a protective earth connection.
3. Apply power to the IP500v2 control unit. The power outlet used must
include a switch and the power outlet must have a protective earth
connection.
4. The control unit will begin loading firmware from the System SD card with
which it will upgrade itself and the components installed in the control
unit.
5. This process takes approximately a minute. The end of this process will
be indicated by LED1 on each base card flashing every 5 seconds. LED9
on each base card fitted with a trunk daughter card will also flash every 5
seconds.
6. The control unit will then begin upgrading the external expansion
modules. This will be indicated by the red center LED on each module
flashing red. The process is completed when the LED changes to steady
green.
7. If a configuration file is already present on the System SD 58 card it is
loaded by the IP Office. If not, the IP Office creates a default
configuration based on the components of the system and copies that
configuration onto the System SD card.
8. It should be possible now to use IP Office Manager to access the
configuration of the IP Office.
The LEDs on the rear of the control unit go through the following sequence during a normal start up. Note that the times
are approximately only:
LED
4s
4s
12s
5s
2s
5s
5s
10s
10s
Finished
CPU
Orange
Green
Green
Green
Green
Green
Green
Green
Green
Green
System SD
Orange
Off
Green
Green
Green
Off
Green
Green
Green
Green
Red
Flash
Optional SD
If present.
Orange
Off
Green
Green
Green
Off
Off
Green
Green
Green
On the front of the control unit, LED1 on any IP500 base cards fitted is used as follows. LED9 is also used for any trunk
daughter cards fitted.
LED
30s
30s
Finished
LED1/LED9
Red
Red
Red
Fast Flash
Flash every 5
seconds
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 75
15-601042 Issue 23f (20 April 2011)
4.11.1 Checking the LEDs
Control Unit LEDs
LED
Description
Optional SD
·
·
·
·
System SD
CPU
Off = Card shutdown 129 .
Green on = Card present.
Green flashing = Card in use.
Orange steady = Reset imminent.
· Red flashing = Card initializing or shutting down.
· Red fast flashing = card full
· Red steady = Card failure/wrong type.
· Alternate red/green = Starting up.
· Green on = Okay.
· Red on = No software.
· Flashing Red = Error/Shutdown.
Base Card LEDs
Base Card
LEDs 1 to 8 Usage
All Cards
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
IP500 Analog Phone
· No status LEDs are used for analog phone extensions.
IP500 Digital Station
· Green On = Phone detected.
IP500 Combination
LEDs 1 to 6
· Green On = Phone detected.
Trunk Daughter Card LEDs
Trunk Daughter Card
LEDs 9 to 12 Usage
All cards
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
Analog Trunk
· Green on = Card fitted.
· Green flashing = Trunk in use.
PRI Trunk
·
·
·
·
BRI Trunk
· Off = No trunk present.
· Green on = Trunk present.
· Green flashing = Trunk in use.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) = Alarm indication
signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in loopback mode (set
through IP Office System Monitor).
External Expansion Module LEDs
· Green on = Module okay.
· Red flashing = Module starting up/Loading firmware.
· Green flashing = Module starting up/Loading firmware (IP500 DS16A/30A module).
· Red on = Error.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 76
15-601042 Issue 23f (20 April 2011)
IP500v2 Installation: Starting the System
4.12 Changing the System to Standard Mode
(Optional) IP Office Essential Edition - Norstar Version is the default mode assumed by a new or default control unit fitted
with an IP Office Norstar SD card. If this is not the mode required for the IP Office system, IP Office Manager can be used
to change the system to IP Office Standard Version.
The process below will change the mode of the system and default its configuration.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Manual Changing to IP Office Standard Version Mode
1. Using IP Office Manager, receive the configuration from the system.
2. When requested, enter the service user name and password. The defaults are Administrator and password.
3. The IP Office Manager application will automatically switch to its simplified view as the configuration from a system
running in IP Office Essential Edition - Quick Version.
4. Select File | Advanced | Switch to Standard Mode (Default).
5. The configuration will be changed to a default one for a IP Office Standard Version system and IP Office Manager
will switch to its advanced view mode.
6. This is a suitable time to begin initial configuration
to restart in IP Office Standard Version mode.
80
before sending the configuration back to the IP Office system
7. Once the system has rebooted, use IP Office Manager to again receive the configuration from the system. The user
name and password for configuration should be the IP Office Standard Version mode defaults Administrator and
Administrator.
Automating the Change to IP Office Standard Version Mode
If the only systems that you install are IP Office Standard Version mode, the Manager application can be used to automate
part of the process above.
1. In IP Office Manager, select File | Preferences.
2. On the Preferences sub-tab, enable Convert default Quick mode to Standard mode.
3. With this option enabled, when a configuration for a new or defaulted system running in IP Office Essential Edition Quick Version mode is received by Manager, it will automatically be converted to a IP Office Standard Version mode
configuration. This setting does not affect existing IP Office Essential Edition - Norstar Version systems with nondefault configurations.
4. ! Important: IP Address Settings Default to Server
The conversion will set the DHCP mode to Server and the LAN addresses to their defaults of 192.168.42.1 and
192.168.43.1. Using Manager to change these settings to the required values.
5. This is a suitable time to begin initial configuration
to restart in IP Office Standard Version mode.
80
before sending the configuration back to the IP Office system
6. Sending the configuration back to the system will restart the system in IP Office Standard Version mode.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 77
15-601042 Issue 23f (20 April 2011)
4.13 Connecting Phones
During initial power up, the IP Office automatically creates extension and user entries for all analog and digital extension
ports (DS and TCM) in the system. This allows those devices to be connected without any additional programming.
·
! Warning
If the system has been upgraded from a previous release of IP Office software, all phones will be restricted from
making any calls until a system upgrade license 203 has been entered. The dialing restriction includes not being able
to make emergency calls.
· This section does not cover the installation of DECT, H323 and SIP telephones. For installation of those devices
refer to the appropriate supplementary installation manuals.
Analog Phones
Connect any analog phones to their appropriate Phone
are clearly labeled as such.
198
ports. Ensure that those connected to power failure ports
35
TCM Port Phones
Connect any TCM phones to their appropriate TCM
201
ports. These phones do not need to load additional firmware.
For some types of phone, the phone can only report its general type to the IP Office but not the specific model. It is
recommended that after connecting all the phones, the phone types should be correctly set in the IP Office configuration.
·
! Important
The default types cannot be changed after installation without defaulting the configuration. Therefore you must
ensure that you connect the correct type of phone to each port.
1. Using IP Office Manager, receive the configuration from the system.
2. Select Extension.
3. Selecting each extension in turn, on the Extn tab, check that the Device Type field is set to the correct phone
model.
Default Type
Possible Phone Models
T7100
T7100, MT7100, MT7100N, Audio Conferencing Unit.
T7208
T7208, MT7208, MT7208N.
M7310
T7406E, T7406, M7310, M7310N
M7310BLF
T7316, M7310BLF
M7324
M7324, M7324N
4. Save the configuration back to the IP Office system.
DS Digital Stations
Connect any digital phones to their appropriate DS 193 ports. These phones may need to upgrade their firmware to match
that supported by the IP Office core software. The appropriate firmware is supplied with the IP Office Manager software
and copied onto the System SD card for IP500v2 systems.
The phones will automatically load the firmware from the IP Office system if necessary.
· The upgrade process takes approximately 10 minutes during which time the phone will display a warning. The
phone should not be disconnected during this process.
· Due to memory requirement, only 10 phones of the same type can be upgraded at a time. Starting from the first
port needing to be upgraded, the IP Office will upgrade all connected phones of the same type needing upgrading in
batches. It will then upgrade the next connected type of phones needing to be upgraded.
· Once the phone connected to a port has been upgraded, the IP Office will not check whether the phone on that port
needs to be upgraded again except following a system reboot, i.e. multiple phones cannot be upgraded by
swapping the connected phones on the same.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 78
15-601042 Issue 23f (20 April 2011)
Chapter 5.
Initial Configuration
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 79
15-601042 Issue 23f (20 April 2011)
5. Initial Configuration
This section covers basic configuration changes required for all IP Office systems.
· Setting the System Locale 81
Setting the correct system locale affects a wide range of settings including trunk settings. The correct locale must
be set for a system to operate correctly.
· Select Key System or PBX System Mode 82
The system can run in key system or PBX system modes.
· Extension Numbering 85
Change the numbering mode used by the system between 2-digit and 3-digit. Renumber the user extensions if
required.
· Change the Default Passwords 84
The default passwords used for configuration access to the IP Office system should be changed.
· Change the IP Address/DHCP Settings 83
If necessary, the IP address and DHCP mode of the IP Office system can be changed.
· Entering Licenses 86
If not already done, enter licenses for features that require them.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 80
15-601042 Issue 23f (20 April 2011)
Initial Configuration:
5.1 Setting the System Locale
Setting the correct system locale 31 affects a wide range of settings including trunk settings. The correct locale must be
set for a system to operate correctly. It will also set the default language used for phone displays and for voicemail
prompts. However language settings can be changed separately from the system locale if different language operation is
required.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
· This process can be performed through phone based administration 52 from either of the first two systems in the
system. For details, refer to the IP Office Essential Edition - Norstar Version Phone Based Administration manual.
Setting the System Locale
· This option can also be done through phone based administration
1. Start Manager
50
52
.
and receive the configuration from the IP Office system.
2. On the Manager home page, select Change System Settings (or from the Admin Tasks list select System).
3. Use the Country drop down list to select the required locale.
· Bahrain
· Morocco
· Qatar
· Turkey
· Egypt
· Oman
· Saudi Arabia
· United Arab Emirates.
· Kuwait
· Pakistan
· South Africa
Use the Language drop down list to select the default language for the system.
4. Click Apply.
5. Click on the
save icon and save the updated configuration back to the IP Office system.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 81
15-601042 Issue 23f (20 April 2011)
5.2 Select Key System or PBX System Mode
IP Office Essential Edition - Norstar Version mode systems can operate in one of two ways, as a key system or as a PBX
system. A IP Office Essential Edition - Norstar Version system defaults to key system operation.
· This process can be performed through phone based administration 52 from either of the first two systems in the
system. For details, refer to the IP Office Essential Edition - Norstar Version Phone Based Administration manual.
Key Mode vs PBX Mode - Quick Summary
Key Mode
PBX Mode
· The first 2 programmable buttons are used as
intercom buttons.
· The first 3 programmable buttons (2 on ETR phones)
are used as call appearance buttons.
· Internal calls are made and answered using the
intercom buttons.
· Internal calls are made and answered using the call
appearance buttons.
· External calls are made and answered using line
appearance buttons.
· External calls are made and answered using the call
appearance buttons.
· The line used for outgoing external calls is determined
by the line button pressed.
· The line used for outgoing external calls is determined
from the number dialed.
· Automatic line selection defaults to the analog lines
present and then the 2 intercom buttons.
· Automatic line selection defaults to the 3 call
appearance buttons.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Selecting Key or PBX System Mode
· This option can be done through phone based administration
1. Start Manager
50
52
.
and receive the configuration from the IP Office system.
2. On the Manager home page, select Change System Settings (or from the Admin Tasks list select System).
3. Use the System Mode drop down list to select the required mode.
4. Click Apply.
5. Click on the
save icon and save the updated configuration back to the IP Office system.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 82
15-601042 Issue 23f (20 April 2011)
Initial Configuration: Select Key System or PBX System Mode
5.3 Changing the IP Address Settings
When a new or defaulted IP Office is switched on, the control unit will make a DHCP requests for IP address settings on
each of its LAN interfaces (LAN1 and LAN2).
· If the IP Office receives a response from a DHCP server, it will configure itself as a DHCP client using the address
details provided by the DHCP server.
· If the IP Office does not receive a response from a DHCP server, it will configure itself as a DHCP server and use
the following default address details:
Network Settings
LAN1
LAN2/WAN
IP address
192.168.42.1.
192.168.43.1
IP Mask
255.255.255.0
255.255.255.0
DHCP Mode
Server
Server
No of DHCP IP Addresses
200.
200.
If the IP address and DHCP mode settings are not suitable for the customers network they should changed. Note that
changing the IP Office's IP address settings requires it to restart.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Changing IP Address Settings
· This option can not be done through phone based administration
1. Start Manager
50
52
.
and receive the configuration from the IP Office system.
2. On the Manager home page, select Change System Settings (or from the Admin Tasks list select System).
3. To use a fixed IP address, deselect Receive IP Address Via DHCP Server. Then in the IP Address (LAN1) and
Sub-Net Mask (LAN1) fields, enter the required IP address settings.
4. Click Apply.
5. Click on the
save icon and save the updated configuration back to the IP Office system.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 83
15-601042 Issue 23f (20 April 2011)
5.4 Changing the Default Passwords
At a minimum you should change the password used for IP Office configuration access. An IP Office system's security
settings can be set back to default 110 if necessary using IP Office Manager.
· This process can be performed through phone based administration 52 from either of the first two systems in the
system. For details, refer to the IP Office Essential Edition - Norstar Version Phone Based Administration manual.
Changing the Remote Administration Password
This password controls remote and local access to the system using IP Office Manager. The default administration
password is password.
· This option can be done through phone based administration
1. Start Manager
50
52
option #730.
and receive the configuration from the IP Office system.
2. On the Manager home page, select Change Remote / Administration Password. A log in dialog is displayed
3. Provide login detail and enter password (case sensitive) as your password. The change dialog is displayed.
4. Enter the new password and and click OK.
Changing the System Password
The system password is used from phones to authorize overriding night service and other settings such as call barring. If a
system password is set, you must enter the system password before you can alter selected settings. By default no system
password is set.
· This option can be done through phone based administration
1. Start Manager
50
52
option #403.
and receive the configuration from the IP Office system.
2. On the Manager home page, select Change System Settings (or from the Admin Tasks list select System).
3. In the System Password field enter the password that should be used.
4. Click Apply.
5. Click on the
icon and save the updated configuration back to the IP Office system.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 84
15-601042 Issue 23f (20 April 2011)
Initial Configuration: Changing the Default Passwords
5.5 Extension Numbering
IP Office Essential Edition - Norstar Version mode systems can use 2-digit or 3-digit numbering. In 2-digit systems, the
user extensions are fixed as 10 to 57. In 3-digit systems the user extension are numbered 100 upwards by default but can
be renumbered in the range 100 to 579.
In 2-digit mode, only 48 extensions are supported, in 3-digit mode a maximum of 100 extensions are supported. It is
strongly recommended that these options are only used and changed on a newly installed system.
· This process can be performed through phone based administration 52 from either of the first two systems in the
system. For details, refer to the IP Office Essential Edition - Norstar Version Phone Based Administration manual.
Changing the Numbering Mode
1. Start Manager and receive the configuration from the IP Office system.
2. Select Tools | Extension Renumber.
· Default Numbering
Select whether the systems uses 2 Digit or 3 Digit extension numbering. In 2 digit systems, the user
extensions are fixed as 10 to 57. In 3 digit systems the user extension are numbered 100 upwards by default
but can be renumbered. In 2 digit mode only 48 extensions are supported, in 3 digit mode a maximum of 100
extensions are supported.
· Renumber From/Renumber To
These options are available for systems set to 3 Digit numbering. They can be used to renumber select
extensions.
3. Click on the save icon and save the updated configuration back to the IP Office system.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 85
15-601042 Issue 23f (20 April 2011)
5.6 Entering Licenses
For IP500v2 control units, license files can be pre-loaded 61 onto the System SD card. Those licenses 202 will then be
merged with the configuration when the control unit is powered up. Otherwise for all control units, licenses can be entered
into the configuration using IP Office Manager. In addition to the methods below, license can also be added by placing the
addition licenses as a text file on the System SD card 61 .
You must ensure that the licenses being entered have been issue against the FK serial number of the System SD card
fitted in the system. Each license is a unique 32-character string based on the feature being licensed and the serial
number of the SD card plugged into the system control unit.
Entering licenses manually is liable to errors caused by miskeying the correct 32-character string.
Entering Licenses
· This option can not be done through phone based administration
1. Start Manager
50
52
.
and receive the configuration from the IP Office system.
2. From the Admin Tasks list select System and then License Management.
· If the Admin Tasks list is not visible, select View and deselect Hide Admin Tasks.
3. It is recommended that you use the Import control to import licenses from a file. Alternatively the license keys can
be cut and pasted into the Key field.
4. Click Apply.
5. Click on the
save icon and save the updated configuration back to the IP Office system.
6. Use Manager to receive the configuration again and check that the status of the license. It should now be Valid.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 86
15-601042 Issue 23f (20 April 2011)
Initial Configuration: Entering Licenses
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 87
15-601042 Issue 23f (20 April 2011)
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 88
15-601042 Issue 23f (20 April 2011)
Chapter 6.
Additional Processes
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 89
15-601042 Issue 23f (20 April 2011)
6. Additional Processes
This section covers the following additional installation processes:
· Switching Off an IP Office System
· Rebooting an IP Office System
· Memory Card Removal
93
· Changing Components
95
92
· Upgrading the IP Office Software
· Out of Building Extensions
· AUX Button Usage
97
25
· Using the External Output Port
· Reset Button Usage
91
105
106
106
· DTE Port Maintenance
107
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 90
15-601042 Issue 23f (20 April 2011)
Additional Processes:
6.1 Switching Off an IP Office System
IP Office systems running IP Office Release 6 can be shut down in order to perform maintenance. The shut down can be
either indefinite or for a set period of time after which the IP Office will automatically reboot.
During the shut down process, the current configuration in the control unit's RAM memory is copied to the control units
non-volatile memory. For IP500v2 systems that location is the System SD card.
For control units with memory cards the memory cards can be shutdown and restarted
129
separately from the system.
! WARNINGS
· A shutdown must always be used to switch off the system. Simply removing the power cord or switching off the
power input may cause errors.
· This is not a polite shutdown, any users calls and services in operation will be stopped. Once shutdown, the system
cannot be used to make or receive any calls until restarted.
· The shutdown process takes up to a minute to complete. When shutdown, the CPU LED and the IP500 base card
LEDs 1 and 9 (if trunk daughter card fitted) will flash red rapidly. The memory card LEDs are extinguished. Do not
remove power from the system or remove any of the memory cards until the system is in the this state.
· To restart a system when shutdown indefinitely, or to restart a system before the timed restart, switch power to
the system off and on again.
System Shutdown Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | System Shutdown.
2. Using the Select IP Office menu, the System Shutdown Mode menu is displayed.
3. Select the type of shutdown required. If Indefinite is used, the system can only be restarted by having its power
switched off and then on again. If a Timed shutdown is selected, the IP Office will reboot after the set time has
elapsed.
System Shutdown Using the System Status Application
1. Start System Status
51
and access the IP Office's status output.
2. In the navigation panel select System.
3. At the bottom of the screen select Shutdown System.
4. Select the time duration for the shutdown or indefinite.
System Shutdown Using the IP500v2 AUX Button
When the AUX button is pressed for more than 5 seconds, the IP500v2 control unit will shutdown with the restart timer
set to 10 minutes.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 91
15-601042 Issue 23f (20 April 2011)
6.2 Rebooting an IP Office System
You can use IP Office Manager to reboot an IP Office system.
1. Using IP Office Manager, select File | Advanced | Reboot.
2. Use the Select IP Office menu to locate and select the IP Office system. Enter a valid user name and password.
3. The type of reboot can then be selected.
· Reboot
Select when the reboot should occur.
· Immediate
Send the configuration and then reboot the IP Office.
· When Free
Send the configuration and reboot the IP Office when there are no calls in progress. This mode can be
combined with the Call Barring options.
· Timed
The same as When Free but waits for a specific time after which it then wait for there to be no calls in
progress. The time is specified by the Reboot Time. This mode can be combined with the Call Barring
options.
· Reboot Time
This setting is used when the reboot mode Timed is selected. It sets the time for the IP Office reboot. If the
time is after midnight, the IP Office's normal daily backup is canceled.
· Call Barring
These settings can be used when the reboot mode When Free is selected. They bar the sending or receiving of
any new calls.
4. Click OK.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 92
15-601042 Issue 23f (20 April 2011)
Additional Processes: Rebooting an IP Office System
6.3 Memory Card Removal
Card
Removal
Memory cards should always be shutdown 129 before being removed when the system is running.
Though the card slot LEDs indicate when data is being written to an card, lack of flashing LED is not a
sufficient safeguard. Shutting down the card will disable embedded voicemail if being used. If the
System SD card is removed, features licensed by the card's Feature Key serial number will continue
operating for up to 2 hours.
Before a memory card is removed from an IP Office system that is running, the card must be shutdown. Removing a
memory card while the system is running may cause file corruption.
Card services can be restarted by either reinserting the card or using a Start Up command.
Card Shutdown Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | Memory Card Commands | Shutdown.
2. Using the Select IP Office menu, select the IP Office system containing the memory card.
3. Click OK.
· At the back of the control unit, confirm that the appropriate memory card LED is off.
· The card can now be removed in order to perform the necessary maintenance actions.
Card Shutdown Using the System Status Application Application
1. Start System Status
51
and access the IP Office's status output.
2. In the navigation panel select System.
3. Select Memory Cards.
4. Select either System Card or Optional Card.
5. At the bottom of the screen select Shutdown.
· At the back of the control unit, confirm that the appropriate memory card LED is off.
· The card can now be removed in order to perform the necessary maintenance actions.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 93
15-601042 Issue 23f (20 April 2011)
Card Reinsertion
Reinserting a memory card into a system that is already switched on will automatically restart card operation. However, if
the card has been shutdown but not removed, it can be restarted using Manager without requiring a reboot.
Card Startup Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | Memory Card Commands | Startup.
2. Using the Select IP Office menu, select the IP Office system containing the memory card.
3. Click OK.
Card Startup Using the System Status Application
3. Start System Status
51
and access the IP Office's status output.
4. In the navigation panel select System.
3. Select Memory Cards.
4. Select either System Card or Optional Card.
5. At the bottom of the screen select Start Up.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 94
15-601042 Issue 23f (20 April 2011)
Additional Processes: Memory Card Removal
6.4 Changing Components
Except for memory cards (see Memory Card Removal 93 ), cards and external expansions modules must only be removed
and added to an IP Office system when that system is switched off 91 .
In the sections below, the term component can refer to a card fitted into the IP Office or an external expansion module.
Note that for extension ports, by default both an extension entry and a user entry will exist in the IP Office configuration.
Extension entries can be deleted without deleting the corresponding user entry. This allows retention of the user settings
and association of the user with a different extension by changing that extensions Base Extension number to match the
user's Extension ID.
Like for Like Replacement
If replacing with a componenet of the same type no configuration changes are necessary.
1. Switch off the IP Office system
91
.
2. Remove the card or external expansion module. Note the card slot or expansion port used as the replacement must
be installed in the same position.
3. Install the replacement using the appropriate process for the type of component (Fitting IP500 cards
External Expansion Modules 71 ).
62
, Adding
4. Restart the IP Office system.
Higher Capacity Replacement
If replacing with a component of the same type but higher capacity, when restarted the IP Office will automatically create
configuration entries for the new trunks or extensions/users.
1. Switch off the IP Office system
91
.
2. Remove the card or external expansion module. Note the card slot or expansion port used as the replacement must
be installed in the same position.
3. Install the replacement using the appropriate process for the type of component (Fitting IP500 cards
External Expansion Modules 71 ).
62
, Adding
4. Restart the IP Office system.
5. Use Manager to configure the new trunks or extensions/users.
Lower Capacity Replacement
If replacing with a component of the same type but lower capacity, after restarting the IP Office the configuration will need
to be edited to remove redundant entries.
1. Switch off the IP Office system
91
.
2. Remove the card or external expansion module. Note the card slot or expansion port used as the replacement must
be installed in the same position.
3. Install the replacement using the appropriate process for the type of component (Fitting IP500 cards
External Expansion Modules 71 ).
62
, Adding
4. Restart the IP Office system.
5. Use Manager to delete the trunks or extensions/users in the configuration that are no longer supported by the
component installed.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 95
15-601042 Issue 23f (20 April 2011)
Adding a New Component
If adding a new component to an available slot or port, when restarted the IP Office will automatically create configuration
entries for the new trunks or extensions/users.
1. Switch off the IP Office system
91
.
2. Install the replacement using the appropriate process for the type of component (Fitting IP500 cards
External Expansion Modules 71 ).
62
, Adding
3. Restart the IP Office system.
4. Use Manager to configure the new trunks or extensions/users.
Permanent Removal
If permanently removing the component, the configuration will need to be edited to remove redundant trunk or extension/
user entries.
1. Switch off the IP Office system
91
.
2. Remove the card or external expansion module.
3. Restart the IP Office system.
4. Use Manager to delete the trunks or extensions/users in the configuration that relate to the component removed.
5. In the Control Unit section of the configuration, delete the entry for the component that is no longer present in the
system.
Replacement of a Different Type
If replacing a component with one of a different type, the process should be divided into two stages. First remove the
existing component using the Permanent Removal process above and adjust the configuration and reboot. Then install
the new component using the Adding a New Component process above.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 96
15-601042 Issue 23f (20 April 2011)
Additional Processes: Changing Components
6.5 Upgrading the IP Office Software
The installed IP Office Manager includes IP Office software files for control units, external expansion modules and phones
appropriate to the IP Office software level.
· New IP500v2 Systems
For the first 90 days, a new IP500v2 control unit will run any supported IP Office Release without requiring an
upgrade license. The highest level run is written into the system's memory (not the SD card) and that becomes a
permanent entitlement for the control unit. However, after 90 days the IP500v2 will require an upgrade license if
upgraded to a software release higher than any that it has run in the initial 90 day period.
·
Warning
Systems upgraded without the appropriate license will display "No license available" and will not allow any
telephony functions.
The IP Office system can be upgraded in two ways:
· Using the IP Office Manager Upgrade Wizard 98
The upgrade wizard is part of IP Office Manager and can be used to upgrade all types of IP Office system.
· Upgrading the System SD Card 100
For IP500v2 control units, the software on the System SD card can be upgraded by a range of methods, i.e. directly
upgrading the SD card or using the upgrade wizard. When the system is rebooted it will use the new software.
WARNINGS
· Check IP Office Technical Bulletins
Check the latest IP Office Technical Bulletin for the IP Office software release before proceeding any further. It may
contain information relating to changes that occurred after this document was completed. Bulletins are available
from http://support.avaya.com.
· Upgrade Path/Multi-Stage Upgrades
Due to the need to adjust internal memory allocation and configuration storage, for some upgrades the control unit
may need to perform multi-stage upgrade process. The table below indicates the require upgrade paths.
Platform
Current Release
Upgrade Step 1
IP500
4.0 / 4.1 / 4.2 / 5.0
Load 7.0
IP500v2
6.0
Load 7.0
All modules
4.0 / 4.1 / 4.2 / 5.0
Load 7.0
· Multiple Managers
If more than one copy of Manager is running it is possible for the IP Office to request BIN files from a different
Manager from the one that started the upgrade process. Ensure that only one copy of Manager is running when
upgrading an IP Office system.
· Other IP Office Applications
Upgrading the core software of the IP Office control unit may require upgrades to associated software. Typically IP
Office is compatible with the previous release of most IP Office applications, however for each IP Office core
software release there may be exceptions. These exceptions will be detailed in the Technical Bulletin for the IP
Office core software release.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 97
15-601042 Issue 23f (20 April 2011)
6.5.1 Using the Upgrade Wizard
1. Ensure that you have a backup copy of the IP Office's configuration before performing this action. If a copy of the
configuration cannot be downloaded using Manager, check the Manager application directory for previously
downloaded configurations.
a. Use Manager to download an up to date copy of the configuration. If that is not possible, check in the Manager
application folder for a previous copy of the configuration.
b. Using IP Office Manager, select File | Open Configuration.
c. Using the Select IP Office Menu, locate and select the IP Office system. Click OK.
d. Enter the name and password for a service user account on that IP Office. Click OK. Manager will receive and
display the configuration from the IP Office.
· If not already done, this action creates a BOOTP entry in Manager for the IP Office system.
· This action also confirms communication between the Manager PC and the IP Office prior to any following
process.
e. Select File | Save Configuration As... and save a copy of the configuration file onto the PC.
2. Select File | Advanced | Upgrade. The UpgradeWiz is started and scans for IP Office modules using the Unit/
Broadcast address. Adjust this address and click Refresh if the expected control units are not shown.
2. The information displayed depends on the type of control unit.
· For IP500v2 control units
The current version of each IP Office .bin file held in the control units memory is shown. That is regardless of
whether that .bin file is currently being used by any module in the system.
· For other control units
For the control unit and each external expansion module present in the system, the current version of software
installed is displayed.
3. The Version column indicates the current version of software installed. The Available column indicates the version
of software Manager has available. If the available version is higher, the check box next to that row is automatically
selected.
· If any of the modules have pre-version 2.1 software installed, an upgrade with Validate unticked is required.
If this is the case, only continue with the upgrade process using a PC with a fixed IP address on the same LAN
domain and physical LAN segment as the IP Office control unit and only upgrade the pre-2.1 system.
· If a multi-stage upgrade is necessary, use the following additional steps to select the appropriate interim
software:
· Right-click on the upgrade wizard and click Select Directory. Locate and select the directory containing
the bin file for the intermediate software level.
· The upgrade wizard should now list just the control unit as having upgrade software available.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 98
15-601042 Issue 23f (20 April 2011)
Additional Processes: Upgrading the IP Office Software
· Upgrading to particular levels of IP Office software require a Software Upgrade X license where X is a
number. The Licensed and Required License columns indicate the current highest upgrade license the
system has and the required software upgrade license for the currently installed software. It does not indicate
the license requirement for the level of software in the Available column. For IP500v2 systems, a value of 255
indicates that the control unit is still in its initial 90 days where it can be upgraded without requiring a license.
4. For those modules which you want to upgrade, tick the check box.
5. For IP500v2 control units, the following additional options are available:
· Backup System Files
If selected, before upgrading to the new software, the current files in the System SD cards /primary folder
will be copied to its /backup folder.
· Upload System Files
If selected, the full set of software files that Manager has is copied to the /primary folder on the System SD
card. In addition to control unit and module software this will include phone software files. Following the
reboot, the phone will upgrade using those files if necessary.
· Restart IP Phones
If selected, following the upgrade and reboot, all Avaya IP phones are also restarted. This will cause them to
recheck whether the firmware they currently have loaded matches that on their configured file server. Use this
option if the IP Office system is the file server and the upgrade included new IP phone firmware.
6. Select Upgrade. The system password for each system will be requested. Enter it and click OK. The next steps
depend on the upgrade options selected. Do not cancel or close the upgrade wizard while these processes are
running.
· Validated Upgrade
If using the Validated option, a number of actions take place as follows;
a. The upgrade wizard checks the amount of free RAM memory available in the control unit to temporarily
store the new BIN files. If insufficient memory is available, you will be prompted whether to continue with
an off-line upgrade or cancel upgrading.
· If offline is selected, the IP Office is rebooted into offline mode. It may be necessary to use the
Refresh option within the Upgrade Wizard to reconnect following the reboot. Validate upgrade can
then be attempted to again check the amount of available RAM memory for transfer of BIN files. If the
memory is still insufficient, the option is offered to either do an unvalidated upgrade or cancel.
b. The bin files required are transferred to the system and stored in temporary memory.
c. For IP500v2 control units, the backup system files and upload system files actions are performed.
d. Once all file transfers are completed, the upgrade wizard will prompt whether it okay to proceed with the
upgrade process. Select Yes to continue.
e. Each module being upgraded will delete its existing core software, restart and load the new software file
that was transferred. This process may take several minutes for each unit.
· Unvalidated Upgrade
This method of upgrading should be avoided unless absolutely necessary. It is only required for IP Office
systems with pre-2.1 software and should only be done from a Manager PC with a fixed IP address running on
the same LAN segment and subnet as the IP Office system. During the upgrade the units and modules erases
their current software and then request the new software file from Manager.
7. Following the upgrade check that the upgrade wizard now shows that the selected units and modules have
upgraded. It may be necessary to select Refresh to update the information in the upgrade wizard display.
8. Repeat the process as required.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 99
15-601042 Issue 23f (20 April 2011)
6.5.2 Using an SD Card
In addition to using the traditional IP Office Upgrade Wizard 98 , IP500v2 control units can be upgraded by loading the
required set of firmware files onto the System SD card and rebooting the system.
·
IP Office Technical Bulletins
Ensure that you have obtained and read the IP Office Technical Bulletin relating to the IP Office software release
which you are installing. This bulletin will contain important information that may not have been included in this
manual. IP Office Technical Bulletins are available from the Avaya support website (http://support.avaya.com).
·
Upgrade Licenses
Some upgrades may require entry of upgrade licenses.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
There are a number of ways in which this can be done.
Method
Using Manager
127
System SD Card
Upgrade 127
Upgrade from
Optional SD Card
128
Description
Location
Using IP Office Manager, the contents of the card are
compared to the files that Manager has available and
are upgraded if necessary.
Local or
Remote
In this method, the System SD card is shut down and
removed from the control unit. The card's contents are
upgraded using IP Office Manager.
Local
This method uses an SD card loaded with the required
version of IP Office software. The card is inserted into
the control unit's Option SD card slot and its contents
copied to the System SD card.
Local
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Software
Files
Embedded
Voicemail
Prompts
–
Page 100
15-601042 Issue 23f (20 April 2011)
Additional Processes: Upgrading the IP Office Software
6.6 Out of Building Telephone Installations
The following are the only supported scenarios in which wired extensions and devices outside the main building can be
connected to the IP Office system. In these scenarios, additional protection, in the form of protective grounding and surge
protectors, must be fitted.
·
WARNING
The fitting of additional protection does not remove the risk of damage. It merely reduces the chances of damage.
· Cables of different types, for example trunk lines, phone extensions, ground and power connections, should be kept
separate.
· All cabling between buildings should be enclosed in grounded ducting. Ideally this ducting should be buried.
· A Primary Protection Box must be provided at the point where the cables enter the building. This should be three
point protection (tip, ring and ground). Typically this would be gas tube protection provided by the local telephone
company. The ground wire must be thick enough to handle all the lines being affected by indirect strike at the same
time.
Connection Type
Protection Device Type
Requirement
Analog Phone Extensions
Phones External expansion
module (POT 198 or PHONE 198 )
ports only.
IP Office Barrier Box 103
· Connection from the expansion module to the
Supports a single connection.
phone must be via a surge protector at each end
Maximum of 16 on any expansion
and via the primary protection point in each
module.
building.
DS Phone Extensions
ITWLinx towerMAX DS/2 102
External expansion module DS Supports up to 4 connections.
193 ports only.
(This device was previously
referred to as the Avaya 146E).
TCM Phone Extensions
None
Analog Trunks
ITWLinx towerMAX CO/4x4
ITWLinx towerMAX SCL/8
(This device was previously
referred to as the Avaya 146G)
· The between building connection must be via
earthed ducting, preferable underground. The cable
must not be exposed externally at any point.
Currently not supported.
102
Supports up to 4 two-wire lines.
(This device was previously
referred to as the Avaya 146C).
External Output Switch
· The IP Office expansion module and control unit
and IROB devices must be connected to the
protective ground point in their building.
For installations in the Republic of South Africa, the
fitting of surge protection on analog trunks is a
requirement.
For other locations where the risk of lightning strikes
is felt to be high, additional protection of incoming
analog trunks is recommended.
Connections from an IP Office Ext O/P port to an
external relay device must be via a surge protector.
The towerMAX range of devices are supplied by ITWLinx (http://www.itwlinx.com).
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 101
15-601042 Issue 23f (20 April 2011)
6.6.1 DS Phones
When digital phone extensions are required in another building, additional In-Range Out-Of-Building (IROB) protective
equipment must be used. For phones connected to IP Office DS 193 ports, the supported device supplied by ITWLinx is a
towerMAX DS/2 module. This IROB device was previous badged by Avaya as the 146E IROB.
·
! WARNING
This device is not supported for TCM port connections, ie. 4100 Series, T-Series, 7400 Series and M-Series phones.
· Only DS connections on an external expansion module are supported. DS ports on cards in the control unit should
not be used.
The protection device should be installed as per the instructions supplied with the device. The ground points on the IP
Office control unit and the DS modules must be connected to a protective ground using 18AWG wire with a green and
yellow sleeve.
Typically the IROBs 2 RJ45 EQUIPMENT ports are straight through connected to the 2 RJ45 LINE ports. This allows existing
RJ45 structured cabling, using pins 4 and 5, to be used without rewiring for up to two DS connection. However each of
these ports can be used to connect a second extension using pins 3 and 6.
LINE
Signal
EQUIPMENT
1
Not used.
1
2
Not used.
2
3
Ring II (Optional)
3
4
Ring I
4
5
Tip I
5
6
Tip II (Optional)
6
7
Not used.
7
8
Not used.
8
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 102
15-601042 Issue 23f (20 April 2011)
Additional Processes: Out of Building Telephone Installations
6.6.2 Analog Phone Barrier Box
Where analog phone extensions are required in another building, additional protective equipment must be used, in the
form of IP Office Phone Barrier Boxes and protective earth connections.
·
CAUTION
PHONE (POT) ports on the front of control units must not be used for extensions that are external to the main
building.
· The correct IP Office specific barrier boxes must be used. These modules have been designed specifically for the
signalling voltages used by the IP Office system:
· Only the IP Office Phone Barrier Box should be used with Phone V1 modules.
· Only the IP Office Phone Barrier Box V2 should be used with Phone V2 modules.
· No other type of analog phone barrier box should be used.
· Where more than 3 barrier boxes are required in a building, they must be rack mounted using a Barrier Box rack
mounting kit 104 .
· A maximum of 16 barrier boxes can be used with any Phone module.
· The Phone Barrier Box does not connect the ringing capacitor in Phone V1 modules.
Main Building
Barrier Box
· RJ11
Connect to PHONE (POT) port on the Phone
module using cable supplied with the barrier
box.
· RJ45
Connect to the secondary building barrier box
via primary protection in both buildings.
· Center Screw
Connect to main building protective ground
(or ground terminal of Barrier Box Rack
Mounting Kit). Use 18AWG (minimum) wire
with a green and yellow sleeve.
· Right-Hand Screw
Connect to ground point on Phone module
using ground cable supplied with barrier box.
1. The
·
·
·
Secondary Building
· RJ11
Connect to analog phone. Cable not
supplied.
· RJ45
From main building via primary
protection in both buildings.
· Center Screw
Connect to main building protective
ground. Use 18AWG (minimum) wire
with a green and yellow sleeve.
· Right-Hand Screw
Not used.
following wires must be kept apart, that is not routed in the same bundle:
Earth leads from the barrier box to the Phone modules.
Internal wires, for example extension leads going directly to the Phone modules.
Wires from external telephone going directly to the barrier boxes.
IP Office Barrier Boxes
SAP Code
IP400 Phone Barrier Box (81V)
Use with Phone V1 module. Includes an RJ45 to RJ11 cable and a
functional earth lead.
700293897
IP400 Phone Barrier Box V2 (101V)
Use with Phone V2 module. Includes an RJ45 to RJ11 cable and a
functional earth lead.
700385495
Barrier Box Rack Mounting Kit
700293905
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 103
15-601042 Issue 23f (20 April 2011)
6.6.3 Rack Mounting Barrier Boxes
Where more than 3 Phone Barrier Boxes are used they must be rack mounted. The Barrier Box Rack Mounting Kit (SAP
Code 700293905) supports up to 8 Phone Barrier Boxes.
1. Unscrew the two screws arranged diagonally at the front of each barrier box and use these same screws to reattach
the barrier box to the rack mounting strip.
2. Each barrier box is supplied with a solid green ground wire connected to its functional ground screw. Remove and
discard this wire. Connect a green/yellow ground wire to the protective earth screw in the center of the Point on the
back of the Barrier Box.
3. The rack mounting strip has threaded M4 earthing pillars. Connect the other end of the barrier box ground wire,
using M4 washers and nuts, to the earthing pillar on that side of the rack mounting strip.
4. Using 14AWG wire with green and yellow sleeve, connect one of the earthing pillars to the buildings protective
earth.
5. Using 14AWG wire with green and yellow sleeve, connect the other earthing pillar to the Phone module.
6. Ensure that the following wires are not routed together in the same bundle:
· Earth lead from the barrier box to the Phone module.
· Internal wires, e.g. wires going directly to the Phone module.
· Wires from external telephone going directly to the barrier boxes.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 104
15-601042 Issue 23f (20 April 2011)
Additional Processes: Out of Building Telephone Installations
6.7 Using the External Output Port
All the IP Office control units are equipped with a EXT O/P port. The port is marked as EXT O/P and is located on the back
of the control unit adjacent to the power supply input socket.
The port can be used to control up to two external devices such as door entry relay switches. The usual application for
these switches is to activate relays on door entry systems. However, as long as the criteria for maximum current, voltage
and if necessary protection are met, the switches can be used for other applications.
The switches can be switched closed, open or pulsed (closed for 5 seconds and then open). This can be done in a number
of ways:
· Using IP Office short codes.
· Through the Door tab in Phone Manager Pro.
· Through the Door Release option in IP Office SoftConsole.
· Via the Open Door action in Voicemail Pro.
Default Short Codes
The following are the default short codes in the IP Office configuration for external output switch operation. They use the
short code features Relay On (closed), Relay Off (open) and Relay Pulse.
State
Switch 1
Switch 2
Closed
*39
*42
Open
*40
*43
Pulse
*41
*44
6.7.1 Port Connection
These ports are found on the rear of all IP Office control units. They are used for connection to external switching relays.
The port uses a standard 3.5mm stereo jack plug for connection.
The IP Office is able to open (high resistance), close (low resistance) or pulse (close for 5 seconds and then open) two
switches within the port. Either switch can be operated separately. These switches are intended for activation of external
relays in systems such as door opening systems.
· CAUTION: In installations where this port is connected to a device external to the building, connection must be via a
towerMAX SCL/8 Surge Protector and a protective ground connection must be provided on the IP Office control unit.
EXT O/P
Pin
Description
1
Switch 1.
2
Switch 2.
3
0 Volts (Ground/Chassis)
· Switching Capacity: 0.7A.
· Maximum Voltage: 55V d.c.
· On state resistance: 0.7 ohms.
· Short circuit current: 1A.
· Reverse circuit current capacity: 1.4A.
· Ensure that pins 1 and 2 are always at a positive voltage with respect to pin 3.
3.5mm stereo audio jack plugs are frequently sold as pre-wired sealed modules. It may be necessary to use a multi-meter
to determine the wiring connections from an available plug. Typically 3 (common to both relays) is the cable screen.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 105
15-601042 Issue 23f (20 April 2011)
6.8 Reset Button
The IP500 and IP500v2 control units have a Reset button. Pressing the button while the control unit is starting up will
pause the start up until the button is released. The effect of pressing the button during normal operation will depend on
how long the button is pressed and is indicated by the CPU LED.
Press Duration
(seconds)
CPU LED
Action
Summary
0 to 5.
Off
None
None.
5 to 10.
Orange
Reboot When Free
Reboot when free with new incoming/outgoing call
barring. A reboot using the reset button is recorded in
the Audit Trail.
10 to 30.
Flashing orange Erase Configuration/
Immediate Reboot
Erase the configuration, alarm log and audit trail.
Immediate reboot without waiting for active calls to end.
See Erasing the configuration 108 for full details.
30 to 40.
Red
Erase All.
Erase configuration, alarm log and core software. See
Erasing the Operational Software 111 for full details.
Over 40.
Flashing green
None
None.
6.9 AUX Button
IP500v2 control units have an AUX button. This button can be used as follows.
If pressed during a restart of the control unit, the control unit skip booting 117 from the /primary folder on the System
SD card. If pressed for more than 5 seconds when a system is running, the control unit will shutdown 91 for 10 minutes.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 106
15-601042 Issue 23f (20 April 2011)
Additional Processes: AUX Button
6.10 DTE Port Maintenance
The DTE port on the back of IP Office control units is not normally used when configuring an IP Office system. However, in
extreme cases, the DTE port can be used to default the system's configuration or to erase it core software if necessary.
·
WARNING
Due to the nature of the actions in this section, they should only be performed if absolutely necessary to return a
system back to working order. In all cases, you must make every effort to ensure that you have a backup copy of
the system configuration.
· The DTE ports on IP Office expansion modules are not used for any maintenance or diagnostics.
6.10.1 DTE Port Settings
These ports are found on the rear of all IP Office control units and external expansion modules. The DTE ports on external
expansion modules are not used.
The RS232 DTE ports on the control units can be used for system maintenance and connection of serial terminal adaptors.
On IP400 control units the port can also be used for connection of the IP Office serial port licence key dongle.
An asynchronous terminal program such as HyperTerminal is also required. Configure this for operation via a PC serial
port, as follows:
Bits per second 38,400
Data bits 8
Parity None
Stop Bits 1
Flow Control None
Settings | Emulation TTY
DTE Cables
These cables are used for system maintenance and diagnostics under Avaya guidance. They can also be used for
connection of RS232 serial terminal adaptor equipment to the IP Office control unit. The cable required depends on the IP
Office control unit. This cable is a "Straight through DB9 female to DB9 male serial cable".
IP Office 9-Way RS232 Signal
DTE Port
PC/Terminal
Adaptor
3
Receive data
3
2
Transmit Data
2
7
RTS (Request To Send)
7
8
CTS (Clear To Send)
8
6
DSR (Data Set Ready)
6
5
Ground
5
1
DCD (Data Carrier Detect)
1
4
DTR (Data Terminal Ready)
4
9
RI (Ring Indicator)
9
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 107
15-601042 Issue 23f (20 April 2011)
6.10.2 Erasing the Configuration
The following processes erases the configuration held in the IP Office control unit's memory. That include both the current
configuration being used in RAM memory and the backup configuration stored in non-volatile memory. Following this the
IP Office will restart with a default configuration.
This process should be performed from a PC with a fixed IP address, directly connected to the IP Office control unit and
with the IP Office system disconnected from any network. Following this process, the control unit's IP address will default
to 192.168.42.1.
·
Do not perform any of these processes unless absolutely necessary. The IP Office's configuration settings can
be default through Manager using the File | Advanced | Erase Configuration command.
· For IP Office Release 7.0 and higher, IP500v2 systems using IP Office A-Law or IP Office Mu-Law System SD
cards will default to IP Office Essential Edition - Quick Version mode. Loading the configuration will switch IP Office
Manager to simplified view. To change the system back to operating in IP Office Standard Version mode, select the
File | Advanced | Change Mode.
Erasing the Configuration via Debug
This process erases the IP Office's configuration settings but does not alter its security settings. It is easier to use than the
boot loader method.
1. Ensure that you have a backup copy of the IP Office's configuration before performing this action. If a copy of the
configuration cannot be downloaded using Manager, check the Manager application directory for previously
downloaded configurations.
a. Use Manager to download an up to date copy of the configuration. If that is not possible, check in the Manager
application folder for a previous copy of the configuration.
b. Using IP Office Manager, select File | Open Configuration.
c. Using the Select IP Office Menu, locate and select the IP Office system. Click OK.
d. Enter the name and password for a service user account on that IP Office. Click OK. Manager will receive and
display the configuration from the IP Office.
· If not already done, this action creates a BOOTP entry in Manager for the IP Office system.
· This action also confirms communication between the Manager PC and the IP Office prior to any following
process.
e. Select File | Save Configuration As... and save a copy of the configuration file onto the PC.
2. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
a. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
a HyperTerminal session, the current settings are summarized across the base of the screen.
107 .
Within
b. Enter AT (note upper case). The control unit should respond OK.
c. Enter AT-DEBUG. The control unit should response with the time and date and then Hello> to show it is ready
to accept commands.
3. To erase the current configuration in RAM memory enter eraseconfig. The Hello> command prompt reappears
when the action is completed.
4. To erase the backup configuration stored in non-volatile Flash memory enter erasenvconfig. The Hello>
command prompt reappears when the action is completed.
5. To reboot the IP Office enter reboot. The IP Office will reboot and restart with a defaulted configuration.
6. Close the terminal program session.
7. Manager can now be used to alter and then upload an old configuration file or receive and edit the control unit's
now defaulted configuration.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 108
15-601042 Issue 23f (20 April 2011)
Additional Processes: DTE Port Maintenance
Erasing the Configuration and Security Settings via the Boot Loader
This process defaults the IP Office security settings and its configurations settings.
2. Ensure that you have a backup copy of the IP Office's configuration before performing this action. If a copy of the
configuration cannot be downloaded using Manager, check the Manager application directory for previously
downloaded configurations.
f. Use Manager to download an up to date copy of the configuration. If that is not possible, check in the Manager
application folder for a previous copy of the configuration.
g. Using IP Office Manager, select File | Open Configuration.
h. Using the Select IP Office Menu, locate and select the IP Office system. Click OK.
i. Enter the name and password for a service user account on that IP Office. Click OK. Manager will receive and
display the configuration from the IP Office.
· If not already done, this action creates a BOOTP entry in Manager for the IP Office system.
· This action also confirms communication between the Manager PC and the IP Office prior to any following
process.
j. Select File | Save Configuration As... and save a copy of the configuration file onto the PC.
2. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
a. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
a HyperTerminal session, the current settings are summarized across the base of the screen.
107 .
Within
b. Arrange the program windows so that the Terminal program and Manager TFTP Log are visible at the same
time.
c. Switch off power to the IP Office control unit.
d. Power on the control unit and press the escape key every second until you get a Loader message. Below is an
example.
P12 Loader 2.4
CPU Revision 0x0900
e. Enter AT (note upper case). The control unit should respond OK.
f. If an OK response is not received, check the settings of your terminal program and repeat the process above.
3. Proceed with the erasure process.
· To erase the alarm log enter AT-X1.
· To erase the current configuration, enter AT-X2. A typical response if Sector 2 Erase (NV Config) followed
by OK. Enter AT-X3. A typical response is Sector Erases (Config) followed by a series of OK responses.
4. Switch power to the control unit off and then back on. Within the terminal program you should see various
messages as the control unit performs various start up tasks.
5. Close the terminal program session.
6. Manager can now be used to alter and then upload an old configuration file or receive and edit the control unit's
now defaulted configuration.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 109
15-601042 Issue 23f (20 April 2011)
6.10.3 Defaulting Security Settings
Procedure: Defaulting Security Settings
This process defaults the IP Office's security settings but does not alter its configuration settings.
1. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
2. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
HyperTerminal session, the current settings are summarized across the base of the screen.
107 .
Within a
3. Enter AT (note upper case). The control unit should respond OK.
4. Enter AT-SECURITYRESETALL.
5. You will be prompted to confirm the control unit's MAC address before continuing. Enter the address.
6. The control unit will respond OK when the action has been completed.
7. Close the terminal program session.
8. Manager can now be used to receive and edit the control unit's now defaulted security settings.
Defaulting the Configuration and Security Settings via the Boot Loader
This process defaults the IP Office security settings and its configurations settings.
1. Ensure that you have a backup copy of the IP Office's configuration before performing this action. If a copy of the
configuration cannot be downloaded using Manager, check the Manager application directory for previously
downloaded configurations.
a. Use Manager to download an up to date copy of the configuration. If that is not possible, check in the Manager
application folder for a previous copy of the configuration.
b. Using IP Office Manager, select File | Open Configuration.
c. Using the Select IP Office Menu, locate and select the IP Office system. Click OK.
d. Enter the name and password for a service user account on that IP Office. Click OK. Manager will receive and
display the configuration from the IP Office.
· If not already done, this action creates a BOOTP entry in Manager for the IP Office system.
· This action also confirms communication between the Manager PC and the IP Office prior to any following
process.
e. Select File | Save Configuration As... and save a copy of the configuration file onto the PC.
2. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
a. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
a HyperTerminal session, the current settings are summarized across the base of the screen.
107 .
Within
b. Arrange the program windows so that the Terminal program and Manager TFTP Log are visible at the same
time.
c. Switch off power to the IP Office control unit.
d. Power on the control unit and press the escape key every second until you get a Loader message. Below is an
example.
P12 Loader 2.4
CPU Revision 0x0900
e. Enter AT (note upper case). The control unit should respond OK.
f. If an OK response is not received, check the settings of your terminal program and repeat the process above.
3. To erase the current configuration in RAM memory enter AT-X3. A typical response is Sector Erases (Config)
followed by a series of OK responses.
4. To erase the backup configuration stored in non-volatile memory enter AT-X2. A typical response if Sector 2
Erase (NV Config) followed by OK. IP Office 403 only: If running an IP Office 403 control unit, also enter AT-X4.
5. Switch power to the control unit off and then back on. Within the terminal program you should see various
messages as the control unit performs various start up tasks.
6. Close the terminal program session.
7. Manager can now be used to alter and then upload an old configuration file or receive and edit the control unit's
now defaulted configuration.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 110
15-601042 Issue 23f (20 April 2011)
Additional Processes: DTE Port Maintenance
6.10.4 Erasing the Operational Firmware
When the firmware loaded by the control unit is erased, the control unit will begin making BOOTP requests for a
replacement firmware file. Manager can act as a BOOTP server and respond to the control units request with the
appropriate file from those installed with Manager.
Unlike other control units, when the firmware loaded by an IP500v2 control unit is erased, the IP500v2 control unit will
first look for replacement firmware on its SD cards before falling back to using a BOOTP request to Manager.
The processes below should be performed from a PC with a fixed IP address, directly connected to the IP Office control
unit and with the IP Office system disconnected from any network. During the process, the control unit's IP address may
default to a value in the 192.168.42.1 to 192.168.42.10 range. If this occurs, it may be necessary to amend the BOOTP
entry in IP Office Manager to match the address the system is using.
·
Do not perform any of the following processes unless absolutely necessary. The IP Office software can normally
be upgraded using IP Office Manager 97 .
·
This process erases the operational software. Before attempting this process you must know the MAC and IP
addresses of the system, plus have a backup copy of its configuration and the correct .bin file for the control unit
type and level of software.
·
The presence of any firewall blocking TFTP and or BOOTP will cause this process to fail.
Erasing the Core Software via Debug
1. Run Manager.
· In the BOOTP entries, check that there is an entry that matches the MAC Address, IP Address and .bin file
used by the system. An entry is normally automatically created when a configuration has been loaded from
that IP Office. .
· If an entry is not present, create a new entry manually. The first two details can be found in the Control
Unit settings in the configuration file. Then close and restart Manager.
· Under File | Preferences ensure that Manager is set to 255.255.255.255. Also check that Enable BootP
Server is checked.
· Select View | TFTPLog.
· Check that the required .bin file is present in Manager's working directory.
2. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
a. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
a HyperTerminal session, the current settings are summarized across the base of the screen.
107 .
Within
b. Enter AT (note upper case). The control unit should respond OK.
c. Enter AT-DEBUG. The control unit should response with the time and date and then Hello> to show it is ready
to accept commands.
3. To erase the current configuration in RAM memory enter upgrade.
4. The IP Office will erase its current software and then send out a BootP request on the network for new software.
Manager will respond and start transferring the software using TFTP.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 111
15-601042 Issue 23f (20 April 2011)
Erasing the Core Software via the Boot Loader
2. Run Manager.
· In the BOOTP entries, check that there is an entry that matches the MAC Address, IP Address and .bin file
used by the system. An entry is normally automatically created when a configuration has been loaded from
that IP Office. .
· If an entry is not present, create a new entry manually. The first two details can be found in the Control
Unit settings in the configuration file. Then close and restart Manager.
· Under File | Preferences ensure that Manager is set to 255.255.255.255. Also check that Enable BootP
Server is checked.
· Select View | TFTPLog.
· Check that the required .bin file is present in Manager's working directory.
2. Attach the serial cable between the PC and the DTE port on the IP Office control unit.
a. Start the terminal program on your PC. Ensure that it has been setup as listed in DTE Port Settings
a HyperTerminal session, the current settings are summarized across the base of the screen.
107 .
Within
b. Arrange the program windows so that the Terminal program and Manager TFTP Log are visible at the same
time.
c. Switch off power to the IP Office control unit.
d. Power on the control unit and press the escape key every second until you get a Loader message. Below is an
example.
P12 Loader 2.4
CPU Revision 0x0900
e. Enter AT (note upper case). The control unit should respond OK.
f. If an OK response is not received, check the settings of your terminal program and repeat the process above.
3. Enter AT-X. The control unit should respond Multi-Sector Erase.
4. The control unit will now request the .bin file it requires. For IP500v2 control units this will be from files on the
System SD card. For other control units it will be from Manager and appears in the TFTP Log.
5. If the file transfers does not appear to be taking place, check that the IP address shown in the TFTP Log matches
the BOOTP entry. Adjust the BOOTP entry if necessary.
6. When completed the system will reboot.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 112
15-601042 Issue 23f (20 April 2011)
Chapter 7.
SD Card Management
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 113
15-601042 Issue 23f (20 April 2011)
7. SD Card Management
The IP500v2 control unit has two SD card slots, labeled System SD and Optional SD respectively. These are used as
follows:
· System SD Card
An Avaya System SD card must be present in this slot at all times. This card holds copies of the IP Office firmware
and configuration and is used as the IP500v2 control units non-volatile memory.
· Each Avaya System SD card has a unique Feature Key serial number which is used for generating and
validating licenses entered into the IP Office configuration.
· The card stores the prompts for embedded voicemail operation and acts as the message store for embedded
voicemail messages.
· Prior to any planned shutdown or restart of the IP Office system, the current configuration running in the IP
Office system's RAM memory is copied to the /primary folder on the System SD card and to the systems nonvolatile memory.
· Following a restart, the software in the /primary folder is loaded by the IP500v2 control unit. If the required
software is not present or valid a sequence of fallback options is used, see Booting from the SD Cards 117 for
full details.
· Following a restart, if present, the configuration file in the /primary folder is loaded by the IP500v2 control
unit. If no file is present the system will check for a file in its internal non-volatile memory. If no copy is found
it will generate a default configuration file. See Booting from the SD Cards 117 for full details.
· Once each day (approximately between 00:00 and 00:30) the IP Office will copy the current configuration
running in its RAM memory to the /primary folder on the card.
· Configuration changes made using IP Office Manager are first written to the copy of the configuration file on
the card and then merged with the configuration running in the IP Office system's RAM memory.
· The write lock setting on cards in the System SD card slot is ignored.
· Optional SD Card
A card does not have to be present in this slot for normal IP Office operation. The slot can be used for various
maintenance actions.
· A card with an updated IP Office software or configuration can be inserted and those files then transferred to
the System SD card in order to upgrade the IP Office system.
· The full contents of the System SD card can be copied to the Optional SD card while the IP Office system is
running.
· The write lock setting on cards in the Optional SD card slot is honored.
Card
Removal
Memory cards should always be shutdown 129 before being removed when the system is running.
Though the card slot LEDs indicate when data is being written to an card, lack of flashing LED is not a
sufficient safeguard. Shutting down the card will disable embedded voicemail if being used. If the
System SD card is removed, features licensed by the card's Feature Key serial number will continue
operating for up to 2 hours.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 114
15-601042 Issue 23f (20 April 2011)
SD Card Management:
Card Maintenance Actions
Using IP Office Manager, IP Office System Status Application or Phone Based Administration
be performed on the SD cards.
, a number of actions can
Action
Description
Shutdown/
Restart 129
Memory cards should always be shutdown 129 before
being removed when the system is running. Though
the card slot LEDs indicate when data is being
written to an card, lack of flashing LED is not a
sufficient safeguard. Shutting down the card will
disable embedded voicemail if being used. If the
System SD card is removed, features licensed by
the card's Feature Key serial number will continue
operating for up to 2 hours.
–
Backup
Copy the files in the /primary folder on the System
SD card to the /backup folder on the card.
6
Copy the files in the /backup folder on the System
SD card to the /primary folder on the card and
restart the IP Office system.
6
Restore
Copy
121
122
Manager
52
System
Status
System
Phone
Copy all the files on the System SD card to the
Optional SD card.
123
Upgrade
Binaries 126
Minutes
90
Copy software files in the /primary folder on the
Optional SD card to the /primary folder on the
System SD card and then restart the IP Office
system.
–
Copy the configuration file in the /primary folder on
the Optional SD card to the /primary folder on the
System SD card and then restart the IP Office
system.
–
–
5 seconds
Upload System
Files 126
Upload a set of IP Office software and embedded
voicemail prompts to the System SD card.
–
–
40
View Files
View the folders and files on the control unit memory
cards.
–
–
–
–
1
–
15
Upgrade
Configuration
120
126
5
The actions below can be performed on cards in a SD
card reader on a PC running IP Office Manager.
Format
119
Reformat a card for IP Office usage without removing
the Feature Key serial number.
·
Recreate
119
This process will erase all existing files on the
card.
Create the folder structure on a memory card and
copy a set of IP Office software files into those
folders.
–
· Process marked as System Phone can be performed through phone based administration 52 from either of the
first two extensions in the system. For details, refer to the IP Office Essential Edition - Norstar Version Phone Based
Administration manual.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 115
15-601042 Issue 23f (20 April 2011)
Card Specification
Non-Avaya cards can be used in the Optional SD slot as long as they match or exceed the standard below:
· SDHC 4GB minimum Class 2+. Single partition FAT32 format.
SD Card Folders
The System SD card contains the following folders:
· /primary
Contains the firmware files for the IP Office control unit, external expansion modules and
supported phones. The folder can also contain music on hold files and license key files. This is the
main set of files used by the IP Office system when booting up. Also contains the stored copy of
the IP Office configuration.
· /backup
Contains a copy of the primary folder at some previous point. A backup copy of the primary
contents to this folder can be invoked manually (using Manager or SSA) or as part of the IP Office
software upgrade using Manager.
· /lvmail
Contains the system prompts used by embedded voicemail. Note that the mailbox messages and
greetings are stored in a sub-folder of the /dynamic folder.
· The sub-folder /AAG is used to store embedded voicemail auto-attendant greetings.
· /doc
Contains initial installation documentation for IP Office and Avaya IP Office Essential Edition
Partner Version.
· /dynamic
Contains files used by the IP Office and retained through a reboot of the IP Office system.
· The sub-folder /lvmail is used to store individual user and group mailbox messages, name
recordings and announcements. The storage capacity for embedded voicemail is limited to 15
hours regardless of the capacity of the card.
· /temp
Contains temporary files used by the IP Office and not retained through a reboot of the IP Office
system.
The Optional SD card can contain a similar set of folders. These are used as an additional backup or they can be used as
the source for upgrading the contents of the System SD card.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 116
15-601042 Issue 23f (20 April 2011)
SD Card Management:
7.1 Booting from the SD Cards
When being powered up, the IP500v2 control unit looks for a valid ip500v2.bin
binary file to load. It does this using the possible source below in the order shown,
skipping to the next source if the file is not present or is not valid.
1. System SD card /primary folder.
2. The control unit's own internal non-volatile memory. Once a system has
been installed, it uses its non-volatile memory to keep copies of the
configuration and system binary files it is using. These can be used to
restore operation during a system reboot. Note that though a system can
boot from non-volatile memory, a System SD card must still be present for
correct system operation.
3. System SD card /backup folder.
4. Optional SD card /primary folder.
5. Optional SD card /backup folder.
6. If no file is found, the control unit will fallback to making BOOTP requests to
the network. IP Office Manager can respond the BOOTP request. See
Erasing the Operational Firmware 111 .
Once a valid ip500v2.bin file is found, the IP Office control unit will load that firmware. The source from which the control
unit binary file was loaded is then used to load further files.
Configuration File Loading
Having installed the necessary system firmware files as above, the IP500v2 control unit requires a configuration file:
· If the IP500v2 booted using binary files from an SD card location, it looks for a valid configuration file in the same
location.
· If a configuration file is present and valid, it is loaded.
· If a configuration file is present but is not valid, load the configuration copy in its non-volatile memory if
present, else it assumes a default configuration.
· If a configuration file is not present, use the non-volatile memory copy as above unless the reboot is as a result
of a default system command.
· If the IP500v2 booted using binary files from its non-volatile memory, it will also load the configuration copy from
that location.
· It will indicate a boot alarm (see below).
· It will attempt to restore the firmware file in the System SD card's /primary folder using the copy in its nonvolatile memory.
· The normal boot up process of upgrading expansion module firmware does not occur. If the File | Advanced |
Upgrade command is used, only external expansion modules actually present in the system are listed for
upgrade.
Post Boot Operation
During normal operation, configuration and binary files sent to the System SD card /primary folder using IP Office
Manager are also written to the non-volatile memory.
If the system has booted from its non-volatile memory due to an SD card problem, it is still possible to upgrade the
ip500v2.bin file using the IP Office upgrade wizard.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 117
15-601042 Issue 23f (20 April 2011)
Boot Alarms
The following apply if the IP500v2 boots using software other than that in its System SD /primary folder:
· An alarm will be shown in the System Status Application. It will also generate an alarm if the card in any slot is not
compatible. These alarms are also output as SNMP, Syslog or email alarms.
· The IP Office Manager Select IP Office menu will display an
icon indicating that the IP Office system is running
using software other than from the System SD card's primary folder.
· The configuration can be read but will be read only. Attempting to send a configuration to the system will cause the
error message Failed to save configuration data. (Internal error).
Bypassing the System SD Card Primary Folder
The control unit can be forced to bypass the System SD card's /primary folder and non-volatile memory when starting.
This is done by pressing the Aux button while applying power to the control unit.
This action may be necessary if, following an upgrade of the IP Office system, it is determined that a roll back to the
previously backed up firmware and configuration is required. Using the Aux button should restore system operation using
the /backup folder files while the installer then restores the contents of the /primary folder to a previous release.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 118
15-601042 Issue 23f (20 April 2011)
SD Card Management: Booting from the SD Cards
7.2 Creating an IP Office SD Card
The processes below can be applied to Avaya IP Office SD cards. They can also be applied to non-Avaya SD cards for use
in a system's Optional SD card slot.
The card must be the following format. For the System SD slot, only Avaya SD cards with a Feature Key should be used.
· SDHC 4GB minimum Class 2+. Single partition FAT32 format.
·
WARNING
Avaya supplied SD cards should not be formatted using any other method than the format commands within IP
Office Manager and IP Office System Status Application. Formatting the cards using any other method will remove
the feature key used for IP Office licensing from the card.
Creating a Card on a Local PC
These processes can be run on an SD card inserted in a card reader on the IP Office Manager PC. That card can then be
used in the System SD card slot of a new system or in the Optional SD card slot of an existing system to upgrade that
system 100 .
Formatting an SD Card
Avaya SD cards should only be formatted using the format options provided within IP Office applications. This process is
not normally necessary with Avaya SD cards unless you suspect that the card has been incorrectly formatted elsewhere.
·
WARNING: All File Will Be Erased
Note that this action will erase any existing files and folders on the card. Once a card has been formatted, the
folders and files required for IP Office operation can be loaded onto the card from the Manager PC using the
Recreate IP Office SD Card command.
1. Insert the SD card into a reader slot on the Manager computer.
2. Using IP Office Manager, select File | Advanced | Format IP Office SD Card.
3. Select IP Office A-Law, IP Office U-Law or IP Office Partner Version. This selection just sets the card label
shown when viewing the card details. It does not affect the actual formatting. Select the label that matches the files
set you will be placing on the card.
4. Browse to the card location and click OK.
5. The status bar at the bottom of Manager will display the progress of the formatting process.
6. When the formatting is complete, you can use the Recreate IP Office SD Card command to load the IP Office
folders and files onto the card from the Manager PC.
Recreating an IP Office SD Card
This command can be used with a read-writeable SD card on the Manager PC. It copies the files and folders used by an
IP500v2 system when starting. It updates the card with the version of those files installed with the IP Office Manager
application. It includes the binary files for the IP500v2 system, external expansion modules and phones. It also includes
the prompt files for embedded voicemail operation.
This process just replaces existing files and adds new files. It does not delete files, so for example, any existing embedded
voicemail messages and greetings are retained. If the card contains dynamic system files such as SMDR records, they are
temporarily backed up by Manager and then restored after the card is recreated.
For the card to be used in an IP500v2 system's System SD slot the card must be Avaya SD Feature Key card. The card
must be correctly formatted, however a reformat of an existing working card is not necessary before using recreate to
update the card contents.
· The source for the files copied to the SD card are the sub-folders of the \Memory Cards folder under Manager's
Working Directory (normally C:\Program Files Avaya\IP Office\Manager). However, if the Working Directory
is changed to a location without an appropriate set of \Memory Cards sub-folders, the required set of files will not
be copied onto the SD card.
1. Once started do not interrupt this process, for example by removing the SD card. This process takes approximately
15 minutes.
2. Insert the SD card into a card reader on the Manager PC.
3. Using IP Office Manager, select File | Advanced | Recreate IP Office SD Card.
4. Select IP Office A-Law, IP Office U-Law or IP Office Partner Version. This selection will affect how the IP
Office systems operates when defaulted with this card present in its System SD card slot. .
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 119
15-601042 Issue 23f (20 April 2011)
5. Browse to the card location and click OK.
6. Manager will start creating folders on the SD card and copying the required files into those folders. This process will
take approximately 15 minutes.
7. Do not remove the SD card during the process. Wait until the Manager displays a message.
7.3 Viewing the Card Contents
Using IP Office Manager you can view the folders and files on the System SD card and the Optional SD card. You can then
use various commands to upload and download files to and from the cards.
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 120
15-601042 Issue 23f (20 April 2011)
SD Card Management: Viewing the Card Contents
7.4 Backing Up the System SD Card
There are two levels of backup that can be performed.
· Backup the System SD Card Primary Folder 121
The contents of the primary folder on the card can be copied to the backup folder. They files can then be restored if
necessary. Both actions can be performed remotely.
· Backup the Whole System SD Card 123
The contents of the whole System SD card can be copied to the Optional SD card. While this can be done remotely,
the contents can only be copied back manually using a card reader.
The backup, restore and copy operations will not be performed if the destination card has insufficient space for the files
being copied.
7.4.1 Backing Up the Primary Folder
This process copies the contents of the /primary folder on the System SD card over the /backup folder. Any files with
matching file names will be replaced.
This takes approximately 6 minutes.
Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Backup System Files.
· The contents of the /primary folder on the System SD card will be copied to the /backup folder. This process
takes approximately 6 minutes.
Using the System Status Application
1. Start System Status
51
and access the IP Office's status output.
2. In the navigation panel select System.
3. At the bottom of the screen select Backup System Files.
· The contents of the /primary folder on the System SD card will be copied to the /backup folder. This process
takes approximately 6 minutes.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 121
15-601042 Issue 23f (20 April 2011)
7.4.2 Restore from the Backup Folder
The contents of the /backup folder on the System SD card can be copied to the /primary folder. Any files with matching
file names will be replaced. The IP Office is then restarted using the files now in the /primary folder.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Restore System Files.
· The contents of the /backup folder on the System SD card will be copied to the /primary folder. The process
takes approximately 6 minutes.
· When the process has been completed, the IP Office system will be restarted.
Using the System Status Application
1. Start System Status
51
and access the IP Office's status output.
2. In the navigation panel select System.
3. At the bottom of the screen select Restore System Files.
· The contents of the /backup folder on the System SD card will be copied to the /primary folder. The process
takes approximately 6 minutes.
· When the process has been completed, the IP Office system will be restarted.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 122
15-601042 Issue 23f (20 April 2011)
SD Card Management: Backing Up the System SD Card
7.4.3 Backing Up to the Optional Card
This process copies all files on the System SD card to the Optional SD card. It includes the /primary and /backup
folders and the embedded voicemail files including message files. Any matching files and folders on the Optional SD card
are overwritten.
The process is a simple copy. Any files already copied that change while the process are not recopied. Any new files added
(for example voicemail messages) while the process is running may not be copied.
This process takes at least 90 minutes and may take much longer depending on the amount of data to be copied, for
example it will be longer if embedded voicemail is being used by the IP Office system to take messages.
Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Copy System Card.
· The contents of the System SD card will be copied to the Optional SD card. This process at least 90 minutes
and can take much longer.
Using the System Status Application
1. Start System Status
51
and access the IP Office's status output.
2. In the navigation panel select System.
3. Select Memory Cards.
4. Select System Card.
5. At the bottom of the screen select Copy System Card.
· The contents of the System SD card will be copied to the Optional SD card. This process at least 90 minutes
and can take much longer.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 123
15-601042 Issue 23f (20 April 2011)
7.4.4 Restoring from the Optional Card
The files in the /primary folder on the Optional SD card can be copied to the /primary folder on the System SD card.
Any files with matching file names will be replaced. The IP Office is then restarted using the files now in the System SD
card's /primary folder.
The restore process is separated into two parts, either copying configuration files from the Optional SD card or copying
software files from the Optional SD card. This allows software files to be copied from an Optional SD card without affecting
the existing configuration of that system.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
7.4.4.1 Restoring a Configuration from an Optional Card
The following processes copy the configuration file (config.cfg) and licenses file (keys.txt). The processes take a few
seconds.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Copying a Configuration from the Optional SD Card File Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Upgrade Configuration.
· The configuration file (config.cfg) and licenses file (keys.txt) in the /primary folder on the Optional SD card
are copied to the /primary folder on the System SD card. This process takes approximately a few seconds.
· When the process has been completed, the IP Office system will be restarted.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 124
15-601042 Issue 23f (20 April 2011)
SD Card Management: Backing Up the System SD Card
7.4.4.2 Restoring Software from an Optional SD Card
These processes copy all files in the folder except the configuration file (config.cfg) and licenses file (keys.txt). The
processes take approximately 5 minutes. These process do not restore embedded voicemail prompts (see Upgrading Card
Software 126 ).
·
IP Office Technical Bulletins
Ensure that you have obtained and read the IP Office Technical Bulletin relating to the IP Office software release
which you are installing. This bulletin will contain important information that may not have been included in this
manual. IP Office Technical Bulletins are available from the Avaya support website (http://support.avaya.com).
·
Upgrade Licenses
Some upgrades may require entry of upgrade licenses.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
Copying Software Files from the Optional SD Card Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Upgrade Binaries.
· The software files (all files in the folder except the configuration file (config.cfg) and licenses file (keys.txt))
in the /primary folder on the Optional SD card are copied to the /primary folder on the System SD card. This
process takes approximately 5 minutes.
· When the process has been completed, the IP Office system will be restarted.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 125
15-601042 Issue 23f (20 April 2011)
7.5 Upgrading Card Software
In addition to using the traditional IP Office Upgrade Wizard 98 , IP500v2 control units can be upgraded by loading the
required set of firmware files onto the System SD card and rebooting the system.
·
IP Office Technical Bulletins
Ensure that you have obtained and read the IP Office Technical Bulletin relating to the IP Office software release
which you are installing. This bulletin will contain important information that may not have been included in this
manual. IP Office Technical Bulletins are available from the Avaya support website (http://support.avaya.com).
·
Upgrade Licenses
Some upgrades may require entry of upgrade licenses.
·
! WARNING
This process will require the IP Office system to reboot in order to complete the process. Any current calls and
services will be ended by the reboot.
There are a number of ways in which this can be done.
Method
Using Manager
127
System SD Card
Upgrade 127
Upgrade from
Optional SD Card
128
Description
Location
Using IP Office Manager, the contents of the card are
compared to the files that Manager has available and
are upgraded if necessary.
Local or
Remote
In this method, the System SD card is shut down and
removed from the control unit. The card's contents are
upgraded using IP Office Manager.
Local
This method uses an SD card loaded with the required
version of IP Office software. The card is inserted into
the control unit's Option SD card slot and its contents
copied to the System SD card.
Local
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Software
Files
Embedded
Voicemail
Prompts
–
Page 126
15-601042 Issue 23f (20 April 2011)
SD Card Management: Upgrading Card Software
7.5.1 Upgrading Remotely Using Manager
This process will copy all system files not present or of a different version compared to those already present on the
System SD card. That includes IP Office software files and embedded voicemail prompt files.
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Backup System Files. The contents of the /primary folder on the System SD card will be copied to
the /backup folder. This process takes approximately 6 minutes.
5. Select File | Upload System Files. The system files that Manager has will be uploaded to the /primary folder on
the System SD card. This includes IP Office software files and embedded voicemail prompt files. Depending on the
files that need to be updated, this process can take up to 40 minutes.
7.5.2 Upgrading the SD Card Locally
The following process can be used if you have physical access to the IP500v2 control unit. This method be used with a
timed reboot, allowing the card upgrade to be done during normal operation hours followed by a reboot outside of normal
operation hours.
If the card is being used for embedded voicemail, that service is not available while the card is shutdown. Licensed
features however will continue running for up to 2 hours while the card is shutdown.
1. Shutdown the System SD memory card
129
and remove it from the control unit.
2. Follow the process for recreating the SD card 119 . This process will overwrite the software files on the card with the
files available to IP Office Manager. It will not affect any other files, for example the configuration file and
embedded voicemail mesages. This process takes approximately 15 minutes.
3. When the recreate process has completed, reinsert the card into the control unit's System SD card slot.
4. Using IP Office Manager select File | Advanced | Reboot.
5. In the Select IP Office menu, select the IP500v2 system and click OK.
6. Select the type of reboot that you want performed and click OK.
7. When the system is rebooted, as it restarts it will load the software files in the primary folder of the System SD
card.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 127
15-601042 Issue 23f (20 April 2011)
7.5.3 Upgrading Using an Optional SD Card
This method allows an Optional SD card to be used as the source from which the System SD card is upgraded. It only
upgrades the software files, it does not update embedded voicemail prompts.
1. Once started do not interrupt this process, for example by removing the SD card. This process takes approximately
15 minutes.
2. Insert the SD card into a card reader on the Manager PC.
3. Using IP Office Manager, select File | Advanced | Recreate IP Office SD Card.
4. Select IP Office A-Law, IP Office U-Law or IP Office Partner Version. This selection will affect how the IP
Office systems operates when defaulted with this card present in its System SD card slot. .
5. Browse to the card location and click OK.
6. Manager will start creating folders on the SD card and copying the required files into those folders. This process will
take approximately 15 minutes.
7. Do not remove the SD card during the process. Wait until the Manager displays a message.
7. Insert the card into the control unit's Optional SD card slot.
8. Use one of the processes below to copy the software from the Optional SD card to the System SD card. Each of
those processes will cause the IP Office system to be restarted.
Copying Software Files from the Optional SD Card Using IP Office Manager
1. Using IP Office Manager, select File | Embedded File Management.
2. Using the Select IP Office menu, select the IP Office system.
3. The file contents of the memory cards are displayed.
4. Select File | Upgrade Binaries.
· The software files (all files in the folder except the configuration file (config.cfg) and licenses file (keys.txt))
in the /primary folder on the Optional SD card are copied to the /primary folder on the System SD card. This
process takes approximately 5 minutes.
· When the process has been completed, the IP Office system will be restarted.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 128
15-601042 Issue 23f (20 April 2011)
SD Card Management: Upgrading Card Software
7.6 Removing SD Cards
Card
Removal
Memory cards should always be shutdown 129 before being removed when the system is running.
Though the card slot LEDs indicate when data is being written to an card, lack of flashing LED is not a
sufficient safeguard. Shutting down the card will disable embedded voicemail if being used. If the
System SD card is removed, features licensed by the card's Feature Key serial number will continue
operating for up to 2 hours.
The following processes can be used with SD cards installed in IP500v2 control units and also with Compact Flash memory
cards installed in IP406 V2 control units.
7.6.1 Card Shutdown
Card
Removal
Memory cards should always be shutdown 129 before being removed when the system is running.
Though the card slot LEDs indicate when data is being written to an card, lack of flashing LED is not a
sufficient safeguard. Shutting down the card will disable embedded voicemail if being used. If the
System SD card is removed, features licensed by the card's Feature Key serial number will continue
operating for up to 2 hours.
Before a memory card is removed from an IP Office system that is running, the card must be shutdown. Removing a
memory card while the system is running may cause file corruption.
Card services can be restarted by either reinserting the card or using a Start Up command.
Card Shutdown Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | Memory Card Commands | Shutdown.
2. Using the Select IP Office menu, select the IP Office system containing the memory card.
3. Click OK.
· At the back of the control unit, confirm that the appropriate memory card LED is off.
· The card can now be removed in order to perform the necessary maintenance actions.
Card Shutdown Using the System Status Application Application
1. Start System Status
51
and access the IP Office's status output.
2. In the navigation panel select System.
3. Select Memory Cards.
4. Select either System Card or Optional Card.
5. At the bottom of the screen select Shutdown.
· At the back of the control unit, confirm that the appropriate memory card LED is off.
· The card can now be removed in order to perform the necessary maintenance actions.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 129
15-601042 Issue 23f (20 April 2011)
7.6.2 Card Startup
Reinserting a memory card into a system that is already switched on will automatically restart card operation. However, if
the card has been shutdown but not removed, it can be restarted using Manager without requiring a reboot.
Card Startup Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | Memory Card Commands | Startup.
2. Using the Select IP Office menu, select the IP Office system containing the memory card.
3. Click OK.
Card Startup Using the System Status Application
1. Start System Status
51
and access the IP Office's status output.
2. In the navigation panel select System.
3. Select Memory Cards.
4. Select either System Card or Optional Card.
5. At the bottom of the screen select Start Up.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 130
15-601042 Issue 23f (20 April 2011)
SD Card Management: Removing SD Cards
7.6.3 System Shutdown
IP Office systems running IP Office Release 6 can be shut down in order to perform maintenance. The shut down can be
either indefinite or for a set period of time after which the IP Office will automatically reboot.
During the shut down process, the current configuration in the control unit's RAM memory is copied to the control units
non-volatile memory. For IP500v2 systems that location is the System SD card.
For control units with memory cards the memory cards can be shutdown and restarted
129
separately from the system.
! WARNINGS
· A shutdown must always be used to switch off the system. Simply removing the power cord or switching off the
power input may cause errors.
· This is not a polite shutdown, any users calls and services in operation will be stopped. Once shutdown, the system
cannot be used to make or receive any calls until restarted.
· The shutdown process takes up to a minute to complete. When shutdown, the CPU LED and the IP500 base card
LEDs 1 and 9 (if trunk daughter card fitted) will flash red rapidly. The memory card LEDs are extinguished. Do not
remove power from the system or remove any of the memory cards until the system is in the this state.
· To restart a system when shutdown indefinitely, or to restart a system before the timed restart, switch power to
the system off and on again.
System Shutdown Using IP Office Manager
1. Using IP Office Manager, select File | Advanced | System Shutdown.
2. Using the Select IP Office menu, the System Shutdown Mode menu is displayed.
3. Select the type of shutdown required. If Indefinite is used, the system can only be restarted by having its power
switched off and then on again. If a Timed shutdown is selected, the IP Office will reboot after the set time has
elapsed.
System Shutdown Using the System Status Application
1. Start System Status
51
and access the IP Office's status output.
2. In the navigation panel select System.
3. At the bottom of the screen select Shutdown System.
4. Select the time duration for the shutdown or indefinite.
System Shutdown Using the IP500v2 AUX Button
When the AUX button is pressed for more than 5 seconds, the IP500v2 control unit will shutdown with the restart timer
set to 10 minutes.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 131
15-601042 Issue 23f (20 April 2011)
Chapter 8.
System Components
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 133
15-601042 Issue 23f (20 April 2011)
8. System Components
This section covers the individual components that can comprise an IP Office installation.
· Control Units
135
· IP500 Base Cards
137
· IP500 Trunk Daughter Cards
144
· IP500 External Expansion Modules
· Feature Keys/SD Cards
· Mounting Kits
· Phones
148
156
158
160
· Phone Add-Ons
176
· Ancilliary Systems
· Physical Ports
· Licenses
180
188
202
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 134
15-601042 Issue 23f (20 April 2011)
System Components:
8.1 IP500v2 Control Unit
The slots are numbered 1 to 4 from left to right. They can be used in any order. However if the capacity for a particular
type of card is exceeded, the card in the rightmost slot will be disabled. The unit must not be used with uncovered slots.
Feature
Capacity
Maximum
Extensions
Up to 100 extensions in IP Office Essential Edition - Norstar Version mode.
Conference
Parties
128 as standard but maximum 64 in any individual conference. Silence suppression is applied to
conferences with more than 10 parties.
Trunks Cards
4. Any combination of IP500 trunk daughter cards and up to 2 IP400 trunk cards.
Voice
Compression
Channels
Up to 20 using IP500 Combination cards.
Voicemail
Channels
For Embedded Voicemail, up to 6 (2 by default, additional channels require licenses).
Locales
Supported in all IP Office locales.
Software Level
IP Office Essential Edition - Norstar Version Mode: 6.1 minimum. Bin file = ip500v2.bin.
Power Supply
Internal power supply unit.
Mounting
Free-standing, rack mounted (requires IP500 Rack Mounting Kit) or wall mounted (requires IP500
Wall Mounting Kit).
Dimensions
Width: 445mm/17.5". Depth: 365mm/14.4". Height: 73mm/2.9"/2U. Clearance: 90mm minimum all
sides, 220m at front.
Memory
Maximum configuration file size: 2048KB.
Name
Description
IPO 500 V2 Base Unit
IP Office 500 V2 Base Unit
700476005
Avaya SD Memory Card
IPO System SD Card A-Law
700479702
IPO System SD Card Mu-Law
700479710
IPO System SD Card Partner
700479728
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
IEC60320 C13 Earthed Power Cord
Country
SAP Code
IP500 Rack Mounting Kit
IP500 Rack Mounting Kit
700429202
IP500 Wall Mounting Kit V2
IP500 Wall Mounting Kit
700500923
IP500 Wall Mounting Kit
IP500 Wall Mounting Kit
700430150
IP500 Blanking Plate Kit
IP500 Blanking Plate Kit
700429194
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 135
15-601042 Issue 23f (20 April 2011)
Ports
Description
AUDIO
AUX
191
3.5mm Stereo jack socket. Used for external music on hold source input.
If pressed during a restart of the control unit, the control unit skip booting 117 from the /primary folder
on the System SD card. If pressed for more than 5 seconds when a system is running, the control unit
will shutdown 91 for 10 minutes.
117
CPU
Indicates the status of the control unit.
· Alternate red/green = Starting up.
· Green on = Okay.
EXPANSION
195
EXT O/P
INPUT
LAN
105
20
· Red on = No software.
· Flashing Red = Error/Shutdown.
RJ45 socket. Used for direct connection to external expansion modules using the Expansion Interconnect
cable supplied with the expansion module.
3.5mm Stereo jack socket. Used for switching external relay systems such as door entry controls. The
port contains two independent switches controlled by the IP Office.
AC power input port.
RJ45 socket. The port is a full-duplex 10/100Mbps auto-sensing, MDI crossover port.
196
Optional SD
Used for the Optional SD card. The LED is used in the same way as for the System SD (see below).
114
RESET
106
This switch is used to restart the IP Office, optionally erasing the configuration and or the core software in
the process. See Reset Button 106 .
RS232
107
9-Way D-Type socket. Used for system maintenance.
System SD
114
WAN
Used for the System SD card,. The LED is used as follows.
·
·
·
·
196
Off = Card shutdown 129 .
Green on = Card present.
Green flashing = Card in use.
Orange steady = Reset imminent.
· Red flashing = Card initializing or shutting down.
· Red fast flashing = card full
· Red steady = Card failure/wrong type.
RJ45 socket. This port is not supported on systems running in IP Office Essential Edition - Norstar Version
mode.
Used for connection of a functional or protective ground 73 . Use of a ground for all systems is
recommended and for some locales may be a regulatory requirement.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 136
15-601042 Issue 23f (20 April 2011)
System Components: IP500v2 Control Unit
8.2 IP500 Base Cards
The IP500 and IP500v2 control units have 4 slots for the insertion of IP500
base cards. The slots are numbered 1 to 4 from left to right. Normally they
can be used in any order, however if the capacity for a particular type of
card is exceeded, the card in the rightmost slot will be disabled.
Each base card includes an integral front panel with ports for cable
connections. Typically the first 8 ports on the left are for connection of
extension devices. The 4 ports on the left are used for connection of trunks
if a trunk daughter card 16 is added to the base card.
IP500 Digital Station Base Card
142
This card provides 8 DS (digital station) ports for the connection of
Avaya digital phones.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
16
which
· Maximum: 3 per control unit.
· Connections for 4100, 7400, M-Series and T-Series phones use
the IP500 TCM8 Digital Station card.
IP500 Analog Phone Base Card
139
The card is available in two variants, supporting either 2 or 8 analog
phone ports.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
16
which
· Maximum: 4 per control unit.
· The analog phone ports do not include a ringing capacitor. Where
this is a requirement, connection should be via a Master socket
containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during power
failure phone port 8 is connected to analog trunk port 12.
IP500 TCM8 Digital Station Card
143
This card provides 8 TCM (digital station) ports for the connection of
Avaya 4100, 7400, M-Series and T-Series phones.
· The card can be fitted with an IP500 trunk daughter card
uses the base card ports for trunk connection.
16
which
· Maximum: 4 per control unit per IP500v2 control unit.
IP500 BRI Combination Card
141
This card provides 6 digital station ports (1-6), 2 analog extension ports
(7-8) and 2 BRI trunk ports (9-10, 4 channels). The card also includes
10 voice compression channels.
· This card has a pre-installed IP500 BRI trunk daughter card
16
.
· Maximum: 2 combination cards per IP500v2 control unit, regardless
of type.
·
IP Office Essential Edition - Norstar Version mode systems are
limited to a maximum of 12 BRI channels.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 137
15-601042 Issue 23f (20 April 2011)
IP500 ATM Combination Card
140
This card provides 6 digital station ports (1-6), 2 analog extension ports
(7-8) and 4 analog trunk ports (9-12). The card also includes 10 voice
compression channels.
· This card has a pre-installed IP500 analog trunk daughter card
16
.
· Maximum: 2 combination cards per IP500v2 control unit, regardless
of type.
· The analog phone ports do not include a ringing capacitor. Where
this is a requirement, connection should be via a Master socket
containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during power
failure phone port 8 is connected to analog trunk port 12.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 138
15-601042 Issue 23f (20 April 2011)
System Components: IP500 Base Cards
8.2.1 Analog Phone
This card is used to add analog phone ports to an IP500 and IP500v2 control unit. It is available in two variants, providing
either 2 or 8 analog extension ports.
· Supports
Provides either 8 or 2 analog
variant.
191
phone ports depending on card
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 4.
· IP500 Trunk Card Support:
Port Type
Ports
Features
Analog
Extension
1 to 8
·
·
·
·
·
1.
Supports ICLID modes DTMFA, DTMFC, DTMFD, FSK and UK20.
REN 2 (1 for external bell device).
Off-Hook current: 25mA
Ring Voltage: 40V.
Intended for connection to two-wire analog phones, the ports do not include a ringing
capacitor. For connection to 4-wire analog phones, connection should be via a master
socket with ringing capacitors.
· If fitted with an analog trunk card, for the Phone 8, during power failure extension port
8 is connected to the analog trunk port 12.
Port LEDs
· No status LEDs are used for analog phone extensions.
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
Optional Trunk
Card Ports
9 to 12
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
The card can be fitted with one trunk daughter card of any type. The trunk daughter card
then uses ports 9 to 12 on the base card for its trunk connections.
Port LEDs
LED use depends daughter card type fitted.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Analog Card
· Green on = Card fitted.
· Green flashing = Trunk in use.
PRI Card
·
·
·
·
BRI Card
· Off = No trunk present.
· Green on = Trunk present.
· Green flashing = Trunk in use.
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) =
Alarm indication signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in
loopback mode (set through IP Office System Monitor).
Name
Description
SAP Code
IPO 500 Extn Card Phone 2
IP Office 500 Extension Card Phone 2
700431778
IPO 500 Extn Card Phone 8
IP Office 500 Extension Card Phone 8
700417231
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 139
15-601042 Issue 23f (20 April 2011)
8.2.2 ATM Combination Card
This card is used to add a combination of ports to an IP500v2 control unit. Not supported by IP500 control units.
· Supports
· 6 Digital Station ports.
· 2 Analog Extension ports.
· 4 Analog Trunk ports.
· 10 voice compression channels.
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 2 combination cards of any type per
IP500v2 control unit.
· IP500 Trunk Card Support:
1. The trunk daughter card is preinstalled and cannot be replaced with another card type.
Port Type
Ports
Features
Digit Station
1 to 6
Provides DS
193
ports for digital stations
29
(except 4100, 4400, 7400, M and T-Series).
LEDs
· Green On = Phone detected.
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
Analog
Extension
7 to 8
·
·
·
·
·
Analog Trunk
9 to 12
·
·
·
·
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Supports ICLID modes DTMFA, DTMFC, DTMFD, FSK and UK20.
REN 2 (1 for external bell device).
Off-Hook current: 25mA
Ring Voltage: 40V.
Intended for connection to two-wire analog phones, the ports do not include a ringing
capacitor. For connection to 4-wire analog phones, connection should be via a master
socket with ringing capacitors.
· During power failure extension port 8 is connected to the analog trunk port 12.
· No status LEDs are used for analog phone extensions.
DTMF, ICLID, Busy tone detection.
Over-voltage and lightning protection.
DTMF and LD dialing.
Adjustable echo cancellation (default 16ms). Selectable to Off, 8, 16, 32, 64 and 128
milliseconds.
LEDs
· Green on = Card fitted.
· Green flashing = Trunk in use.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Name
Description
SAP Code
IPO IP500v2 COMBINATION
CARD ATM
IPO IP500v2 COMBINATION CARD ATM
700476013
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 140
15-601042 Issue 23f (20 April 2011)
System Components: IP500 Base Cards
8.2.3 BRI Combination Card
This card is used to add a combination of ports to an IP500v2 control unit. Not supported by IP500 control units.
· Supports
· 6 Digital Station ports.
· 2 Analog Extension ports.
· 2 BRI Trunk ports (4 BRI channels).
· 10 voice compression channels.
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 2 combination cards of any type.
·
IP Office Essential Edition - Norstar Version mode systems are
limited to a maximum of 12 BRI channels.
1. The trunk daughter card is pre· IP500 Trunk Card Support:
installed and cannot be replaced with another card type.
Port Type
Ports
Features
Digit Station
1 to 6
Provides DS
193
ports for digital stations
29
(except 4100, 4400, 7400, M and T-Series).
LEDs
· Green On = Phone detected.
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Analog
Extension
7 to 8
·
·
·
·
·
BRI Trunk
9 to 10
· Each trunk port supports 2B+D channels.
· ETSI or AusTS013 basic rate protocol set through the IP Office configuration.
Supports ICLID modes DTMFA, DTMFC, DTMFD, FSK and UK20.
REN 2 (1 for external bell device).
Off-Hook current: 25mA
Ring Voltage: 40V.
Intended for connection to two-wire analog phones, the ports do not include a ringing
capacitor. For connection to 4-wire analog phones, connection should be via a master
socket with ringing capacitors.
· No status LEDs are used for analog phone extensions.
LEDs
·
·
·
·
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
Not Used
11 to 12
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
–
Name
Description
SAP Code
IPO IP500v2 COMBINATION
CARD BRI
IPO IP500v2 COMBINATION CARD BRI
700476021
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 141
15-601042 Issue 23f (20 April 2011)
8.2.4 Digital Station
This card is used to add digital station (DS) extension ports to an IP500 and IP500v2 control unit. It provides 8 RJ45 DS
extension ports for use with Avaya digital phones. A further 4 RJ45 ports are provided for trunk connections when an
IP500 trunk card is fitted to this card.
· Supports
Provides 8 DS 193 ports for digital stations
7400, M and T-Series).
29
(except 4100, 4400,
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 3 per control unit.
· IP500 Trunk Card Support:
Port Type
Ports
Features
Digit Station
1 to 8
Provides DS
193
ports for digital stations
29
1.
(except 4100, 4400, 7400, M and T-Series).
LEDs
· Green On = Phone detected.
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
Optional Trunk
Card Ports
9 to 12
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
The card can be fitted with one trunk daughter card of any type. The trunk daughter card
then uses ports 9 to 12 on the base card for its trunk connections.
Port LEDs
LED use depends daughter card type fitted.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Analog Card
· Green on = Card fitted.
· Green flashing = Trunk in use.
PRI Card
·
·
·
·
BRI Card
· Off = No trunk present.
· Green on = Trunk present.
· Green flashing = Trunk in use.
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) =
Alarm indication signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in
loopback mode (set through IP Office System Monitor).
Name
Description
SAP Code
IPO 500 Extn Card Dgtl Sta 8
IP Office 500 Extension Card Digital Station 8
700417330
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 142
15-601042 Issue 23f (20 April 2011)
System Components: IP500 Base Cards
8.2.5 TCM8 Digital Station
This card is used to add TCM RJ45 201 extension ports to an IP500v2 control unit. It provides 8 RJ45 extension ports for
supported M-Series and T-Series digital stations. It can also be used for 4100 and 7400 Series phone support by
connection to a Digital Mobility Solution 180 system.
A further 4 RJ45 ports are provided for trunk connections when an IP500 trunk card is fitted to this card.
· Supports
Provides 8 TCM 201 ports for supported 4100, 4400, 7400, M and TSeries digital stations.
· IP500 Control Unit:
· IP500v2 Control Unit:
· Maximum per Control Unit: 4.
· IP500 Trunk Card Support:
1.
Port Type
Ports
Features
TCM
1 to 8
Cable lengths up to 305 m (1000 ft) using 0.5mm (24AWG) wires do not require a power
booster. Lengths up to 790 m (2600 ft) are supported if an auxiliary power supply booster
is used.
LEDs
· Green On = Phone detected.
· LED1 is also used for base card status:
· Red On = Error
· Red Slow Flash = Initializing.
Optional Trunk
Card Ports
9 to 12
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
The card can be fitted with one trunk daughter card of any type. The trunk daughter card
then uses ports 9 to 12 on the base card for its trunk connections.
LEDs
LED use depends daughter card type fitted.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card okay.
· Red Fast Flash = System shutdown.
Analog Card
· Green on = Card fitted.
· Green flashing = Trunk in use.
PRI Card
·
·
·
·
BRI Card
· Off = No trunk present.
· Green on = Trunk present.
· Green flashing = Trunk in use.
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) =
Alarm indication signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in
loopback mode (set through IP Office System Monitor).
Name
Description
SAP Code
IPO 500 TCM 8
IP Office 500 TCM 8
700500758
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 143
15-601042 Issue 23f (20 April 2011)
8.3 IP500 Trunk Daughter Cards
Most IP500 base cards 14 can be fitted with an IP500 trunk daughter
cards to support the connection of trunks to the base card.
Each daughter card is supplied with the stand off pillars required for
installation and a label to identify the daughter cards presence on the
front of the base card after installation.
· IP500 Combination cards are pre-fitted with a trunk daughter card
which cannot be removed or changed for another type of trunk
daughter card.
IP500 Analog Trunk Daughter Card
145
This card allows the base card to support 4 analog loop-start trunks.
· The analog phone ports do not include a ringing capacitor.
Where this is a requirement, connection should be via a Master
socket containing ringing capacitors.
· If fitted with an IP500 Analog Trunk daughter card, during
power failure phone port 8 is connected to analog trunk port
12.
· Maximum: 4 per control unit.
IP500 PRI-U Trunk Daughter Card
147
This card allows the base card to support up to 2 PRI trunk
connections. The card is available in single and dual port variants.
The card can be configured for E1 PRI, T1 robbed bit, T1 PRI or E1R2
PRI trunks.
· Maximum: 1 single port card per control unit.
· The IP Office system supports 8 unlicensed B-channels on each
IP500 PRI-U port fitted. Additional B-channels, up to the capacity
of ports installed and PRI mode selected require IP500 Universal
PRI (Additional Channels) 204 licenses added to the
configuration. These additional channels consume the licenses
based on which additional channels are configured as in-service
from port 9 of slot 1 upwards. D-channels are not affected by
licensing.
IP500 BRI Trunk Daughter Card
146
This card allows the base card to support up to 4 BRI trunk
connections, each trunk providing 2B+D digital channels. The card is
available in 2 port (4 channels) and 4 port (8 channels) variants.
· Maximum: 4 per control unit.
·
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
IP Office Essential Edition - Norstar Version mode systems are
limited to a maximum of 12 BRI channels.
Page 144
15-601042 Issue 23f (20 April 2011)
System Components: IP500 Trunk Daughter Cards
8.3.1 Analog Trunk Card
This card can be added to an IP500 base card to provide that card with support for 4 loop-start analog trunks.
This card can be fitted to any IP500 base card.
· Ports/Channels
4 Loop-start analog trunk ports. Connections via the host IP500 base card.
· DTMF, ICLID, Busy tone detection.
· Over-voltage and lightning protection (may still require additional
protection equipment see Lightning Protection/Out-of-Building
Connections 25 .
· DTMF and LD dialing.
· Adjustable echo cancellation (default 16ms). Selectable to Off, 8, 16, 32,
64 and 128 milliseconds.
· Power Failure Port
Regardless of the IP500 card hosting it, during power failure pins 4 and 5
of port 12 are connected to pins 7 and 8. In addition, when fitted to an
IP500 Analog Phone 8 base card, during power failure extension port 8 is
connected to the analog trunk port 12.
· License: No license required.
· Maximum per Control Unit: 4.
· IP Office Software Level: 4.0+.
Daughter Card Ports (9-12)
The LEDs for ports 9 to 12 of the IP500 base card are used as follows:
· Green on = Card fitted.
· Green flashing = Trunk in use.
· LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card
okay.
· Red Fast Flash = System shutdown.
Name
Description
SAP Code
IPO 500 Trnk Anlg 4 Uni
IP Office 500 Trunk Card Analog 4 Universal
700417405
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 145
15-601042 Issue 23f (20 April 2011)
8.3.2 BRI Trunk Cards
This card can be added to an IP500 base card to provide that card with support for BRI-To
in 8 channel (4 physical trunks) or 4 channel (2 physical trunks) variants.
192
trunks. The card is available
This card can be fitted to any IP500 base card.
· Ports/Channels
2 or 4 BRI trunk ports. Connections via ports 9 to 12 of the host IP500 base
card.
· Each trunk port supports 2B+D channels.
· ETSI or AusTS013 basic rate protocol set through the IP Office
configuration.
· License: No license required.
· Maximum per Control Unit: 4.
·
IP Office Essential Edition - Norstar Version mode systems are limited
to a maximum of 12 BRI channels.
· IP Office Software Level: 4.0+.
· This card is approved for use in the following countries:
Brazil.
New Zealand.
China.
Russia.
India.
South Africa.
Argentina.
United Arab Emirates (UAE).
Australia.
European Union (EU).
Daughter Card Ports (9-12)
The LEDs for ports 9 to 12 of the IP500 base card are used as follows:
·
·
·
·
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
LED 9 is also used for daughter card status.
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card
okay.
· Red Fast Flash = System shutdown.
Name
Description
SAP Code
IPO 500 Trnk BRI 4 Uni
IP Office 500 Trunk Card Basic Rate 4 Universal
700417413
IPO 500 Trnk BRI 8 Uni
IP Office 500 Trunk Card Basic Rate 8 Universal
700417421
IP0 IP500 BRI S0 CONVTR
CBL
IP500 BRI So Converter Cable
700458649
IP0 IP500 BRI S0 CONVTR
CBL
IP500 BRI So Converter Cable
700458649
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 146
15-601042 Issue 23f (20 April 2011)
System Components: IP500 Trunk Daughter Cards
8.3.3 PRI Trunk Cards
This card can be added to an IP500 base card to provide that card with support for PRI trunks. The card is available in
single port or dual port variants.
This card can be fitted to any IP500 base card.
· Ports/Channels
1 or 2 PRI trunk ports 199 . Each port supports the following PRI line types.
On dual port cards, both ports will be the same line type. The line type
selection can be changed using IP Office Manager. The options available
depend on the IP Office operation mode and locale.
· E1 PRI (30B+D channels per port).
· E1R2 PRI (30B channels per port).
· T1 robbed bit (24B channels per port) or T1 PRI (23B+D channels
per port).
· The required mode can be selected within IP Office Manager by rightclicking on the line icon and selecting Change Universal PRI Card
Line Type and then selecting the required line type.
· Physical trunk connection is via ports 9 and 10 of the host IP500 base
card.
· Port 11 and 12 can be used as test points for connection of test and
monitoring equipment for the adjacent port.
· Licenses
The IP Office system supports 8 unlicensed B-channels on each IP500 PRI-U
port fitted. Additional B-channels, up to the capacity of ports installed and
PRI mode selected require IP500 Universal PRI (Additional Channels)
licenses added to the configuration. These additional channels consume the
licenses based on which additional channels are configured as in-service
from port 9 of slot 1 upwards. D-channels are not affected by licensing.
· Maximum per Control Unit: 1 single port card per control unit. Not
supported in conjunction with BRI trunk cards in the same system.
· Software Level: 4.1+.
Daughter Card Ports (9-12)
The LEDs for ports 9 to 12 of the IP500 base card are used as follows:
Off = No trunk present.
Green on = Trunk present.
Green flashing = Trunk in use.
Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) = Alarm
indication signal (AIS) from the trunk remote end.
· Red with Green Blink (port 9) or Green Blink (port 10) = Port in loopback
mode (set through IP Office System Monitor).
· LED 9 is also used for daughter card status.
·
·
·
·
· Red On = Error
· Red Slow Flash = Initializing.
· Red Flash every 5 seconds = Card
okay.
· Red Fast Flash = System
shutdown.
Name
Description
SAP Code
IPO 500 TRNK PRI 1 UNI
IP Office 500 Trunk Card Primary Rate 1 Universal
700417439
IPO 500 TRNK PRI 2 UNI
IP Office 500 Trunk Card Primary Rate 2 Universal
700417462
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 147
15-601042 Issue 23f (20 April 2011)
8.4 IP500 Expansion Modules
The following IP500 external expansion modules are supported by IP Office Release 7.0. Each module uses an external
power supply unit 19 supplied with the module. A locale specific power cord 20 for the PSU must be ordered separately.
If being rack mounted, these units use the IP500 rack mounting kit. They can be wall mounted using the new wall
mounting kit V2.
· Systems running in IP Office Essential Edition - Norstar Version mode support up to 8 external expansion modules
so long as the system extensions limit is not exceeded.
· IP500 Digital Station Module 149
Provides, depending on variant, an additional 16 or 30 DS
supported Avaya DS digital phones 29 .
193
ports for
· IP500 Digital Station A Module 151
Provides, depending on variant, an additional 16 or 30 TCM 201 ports for
supported Avaya TCM digital phones 29 . Supported by IP500v2 only.
· IP500 Phone Module 154
Provides, depending on variant, an additional 16 or 30 PHONE
analog phones.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
198
ports for
Page 148
15-601042 Issue 23f (20 April 2011)
System Components: IP500 Expansion Modules
8.4.1 Digital Station
IP Office 500 Digital Station modules can be used to add additional DS ports to an IP Office system. The module is
available in 16 and 30 port variants, referred to as the IP500 Digital Station 16 and IP500 Digital Station 30 respectively.
Feature
Details
Supported on
IP500 and IP500v2.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 2.1(31) minimum. Bin file = nadcpV2.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a Earthed 3-Pin, 60W external power supply module. The PSU has an
integral power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C13
power cord 19 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP500 Rack
Mounting Kit. It can be wall mounted using the IP500 Wall Mounting Kit V2.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8".
Weight
Unboxed: 3.5Kg/7.8lbs. Boxed: 4.8Kg/10.8lbs. (Based on DS30 V2)
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 149
15-601042 Issue 23f (20 April 2011)
IPO 500 Digital Station Connections
Ports
DC I/P
DS
Description
DC power input port. Used for connection of the power lead from an Avaya earthed 60W external
power supply unit supplied with the expansion module. A locale specific IEC60320 C13 power cord
for the external PSU is required but is not supplied with the module.
193
RJ45 socket. Digital Station port. Used for connection of IP Office supported DS phones 29 .
If connected to an out-of-building extension 25 , the connection must be made via additional IROB
barrier devices in addition to the buildings primary protection. The module must also be connected to
a protective ground.
193
DTE
9-Way D-Type socket. For Avaya use only.
107
EXPANSION
19
195
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
Protective Ground point. Use of a protective ground is required for all installations, see Grounding
(Earthing) 73 . Where the module is connected to analog extensions in another building, an IP Office
Phone Barrier Box V2 (101V) is required at both ends, see Lightning Protection/Out-of-Building
Connections 25 .
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IPO 500 Digital Station
16 Ports
All
700449499
30 Ports
IEC60320 C13 Power Cord
700426216
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
IP500 Wall Mounting Kit V2
All
700500923
IP500 Rack Mounting Kit
All
700429202
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 150
15-601042 Issue 23f (20 April 2011)
System Components: IP500 Expansion Modules
8.4.2 Digital Station A
IP Office 500 Digital Station A modules can be used to add additional TCM 200 ports to an IP Office system. They provides
extension ports for supported M-Series and T-Series digital stations. They can also be used for 4100 and 7400 Series
phone support by connection to a Digital Mobility Solution 180 system.
The module is available in 16 and 30 port variants, referred to as the IP500 Digital Station 16A and IP500 Digital Station
30A respectively. Connection is via 1 (16 port version) or 2 (30 port version) J21 connectors.
Feature
Details
Supported on
IP500v2 only.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 7.0 minimum. Bin file = nadcpaV1.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a Earthed 3-Pin, 60W external power supply module. The PSU has an
integral power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C13
power cord 19 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP500 Rack
Mounting Kit. It can be wall mounted using the IP500 Wall Mounting Kit V2.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8".
Weight
Unboxed: 3.5Kg/7.8lbs. Boxed: 4.8Kg/10.8lbs. (Based on DS30A)
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 151
15-601042 Issue 23f (20 April 2011)
IPO 500 Digital Station A Connections
LEDs 1 to 16 or 1 to 30 indicate when a phone is connected. They do not indicate phone activity. The center LED indicate
the module status (Green = Okay, Red = Error, Flashing = Loading firmware).
Ports
DC I/P
Description
TCM RJ21
DTE
DC power input port. Used for connection of the power lead from an Avaya earthed 60W external
power supply unit supplied with the expansion module. A locale specific IEC60320 C13 power cord
for the external PSU is required but is not supplied with the module.
193
RJ21 port. Provides extension ports for supported M-Series and T-Series digital stations. They can also
be used for 4100 and 7400 Series phone support by connection to a Digital Mobility Solution 180
system.
200
9-Way D-Type socket. For Avaya use only.
107
EXPANSION
19
195
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
Protective Ground point. Use of a protective ground is required for all installations, see Grounding
(Earthing) 73 . Where the module is connected to analog extensions in another building, an IP Office
Phone Barrier Box V2 (101V) is required at both ends, see Lightning Protection/Out-of-Building
Connections 25 .
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IP500 Digital Station A
16 Ports
All
700500699
30 Ports
IEC60320 C13 Power Cord
700500698
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
IP500 Wall Mounting Kit V2
IP500 Rack Mounting Kit
700500923
All
700429202
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 152
15-601042 Issue 23f (20 April 2011)
System Components: IP500 Expansion Modules
RJ21 Cable Pin Out
The following pin-out is used for the RJ21 ports.
1st RJ21 Connector
Port
1
Tip
Ring
2
Tip
Ring
3
Tip
Ring
4
Tip
Ring
5
Tip
Ring
6
Tip
Ring
7
Tip
Ring
8
Tip
Ring
9
Tip
Ring
10
11
12
13
14
15
16
Not Used
2nd RJ21 Connector
Pin
Wire
Port
26
White/Blue
1
1
Blue/White
27
White/Orange
2
Orange/White
28
White/Green
3
Green/White
29
White/Brown
4
Brown/White
30
White/Slate
5
Slate/White
31
Red/Blue
6
Blue/Red
32
Red/Orange
7
Orange/Red
33
Red/Green
8
Green/Red
34
Red/Brown
9
Brown/Red
Tip
35
Red/Slate
Ring
10
Slate/Red
Tip
36
Black/Blue
Ring
11
Blue/Black
Tip
37
Black/Orange
Ring
12
Orange/Black
Tip
38
Black/Green
Ring
13
Green/Black
Tip
39
Black/Brown
Ring
14
Brown/Black
Tip
40
Black/Slate
Ring
15
Tip
Ring
Tip
Ring
2
Tip
Ring
3
Tip
Ring
4
Tip
Ring
5
Tip
Ring
6
Tip
Ring
7
Tip
Ring
8
Tip
Ring
9
Tip
Ring
Wire
26
White/Blue
1
Blue/White
27
White/Orange
2
Orange/White
28
White/Green
3
Green/White
29
White/Brown
4
Brown/White
30
White/Slate
5
Slate/White
31
Red/Blue
6
Blue/Red
32
Red/Orange
7
Orange/Red
33
Red/Green
8
Green/Red
34
Red/Brown
9
Brown/Red
Tip
35
Red/Slate
Ring
10
Slate/Red
Tip
36
Black/Blue
Ring
11
Blue/Black
Tip
37
Black/Orange
Ring
12
Orange/Black
Tip
38
Black/Green
Ring
13
Green/Black
Tip
39
Black/Brown
Ring
14
Brown/Black
40
Black/Slate
Slate/Black
15
Slate/Black
41
Yellow/Blue
41
Yellow/Blue
16
Blue/Yellow
16
Blue/Yellow
42
Yellow/Orange
42
Yellow/Orange
17
Orange/Yellow
17
Orange/Yellow
43
Violet/Slate
43
Violet/Slate
08
Slate/Violet
08
Slate/Violet
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
10
Pin
11
12
13
14
Not Used
Page 153
15-601042 Issue 23f (20 April 2011)
8.4.3 Phone
IP500 Phone modules can be used to add additional PHONE ports to an IP Office system.
The module is available in 16 and 30 port variants, referred to as the IP500 Phone 16 and IP500 Phone 30 respectively.
Feature
Details
Supported on
IP500 and IP500v2.
Locales
Supported in all IP Office locales.
Software Level
IP Office core software level 2.1(36) minimum. Bin file = dvpots.bin.
Included
Power supply unit (see below) and Expansion Interconnect cable.
Power Supply
The module is supplied with a Earthed 3-Pin, 60W external power supply unit. The PSU has an
integral power cord for connection to the module's DC I/P socket. A locale specific IEC60320 C13
power cord 19 for the external PSU is required but is not supplied with the module.
Mounting
The module is designed as a free-standing module that can be stacked on or under other IP Office
modules. The module can be rack mounted in a 19" rack system using the optional IP500 Rack
Mounting Kit. It can be wall mounted using the IP500 Wall Mounting Kit V2.
Dimensions
Width: 445mm/17.5". Depth: 245mm/9.7". Height: 71mm/2.8".
Weight
Unboxed: 3.1Kg/6.94lbs. Boxed: 4.4Kg/9.7lbs. (Based on Phone 30 V2)
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 154
15-601042 Issue 23f (20 April 2011)
System Components: IP500 Expansion Modules
IPO 500 Phone Connections
Ports
DC I/P
DTE
Description
193
9-Way D-Type socket. For Avaya use only.
107
EXPANSION
195
PHONE
DC power input port. Used for connection of the power lead from an Avaya earthed 60W external power
supply unit supplied with the expansion module. A locale specific IEC60320 C13 power cord 19 for the
external PSU is required but is not supplied with the module.
198
RJ45 Socket. Used for direct connection to an Expansion port on an IP Office control unit using the
Expansion Interconnect cable supplied with the module.
RJ45 socket. Used for connection of analog phones. Intended for two-wire analog phones. For
connection to 4-wire analog phones connection should be via a master socket with ringing capacitors.
If connected to an out-of-building extension 25 , the connection must be made via additional IP Office
Barrier Boxes 103 in addition to the buildings primary protection. The module must also be connected to
a protective ground.
Protective Ground point. Use of a protective ground is required for all installations, see Grounding
(Earthing) 24 . Where the module is connected to analog extensions in another building, an IP Office
Phone Barrier Box V2 (101V) is required at both ends, see Lightning Protection/Out-of-Building
Connections 25 .
All expansion modules are supplied with a base software level and should be upgraded to match the core software of the
control unit in the IP Office system.
Item
Variant
Country
SAP Code
IPO 500 Phone
16 Ports
All
700449507
30 Ports
All
700426224
CEE7/7
Europe
700289762
BS1363
United Kingdom
700289747
NEMA5-15P
America
700289770
IEC60320 C13 Power Cord
IP500 Wall Mounting Kit V2
IP500 Rack Mounting Kit
700500923
All
700429202
Expansion modules include an external power supply unit (PSU) and an appropriate interconnect cable. They do not
include a locale specific power cord for the external PSU or any phone extension cables.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 155
15-601042 Issue 23f (20 April 2011)
8.5 Feature Keys
The serial number of the feature key fitted to the IP Office control unit is used as the basis for all licenses issued for that
IP Office system and is used to regularly re-validate the licenses. If the feature key is removed, over the next few hours
licensed features will stop operating.
8.5.1 IP500v2 System SD Cards
This type of feature key is used with IP500v2 control units and is a mandatory item. The control unit must be fitted with
one of these feature keys even if no licenses are being used.
The serial number for licenses issued for use with this type of feature key is printed on the card label and prefixed by FK.
This type of feature key is also a memory card used for other system functions and to provide embedded voicemail if
required.
· By default the card can be used for 2 ports of embedded voicemail. Additional ports up to a maximum of 6 can be
enabled by the addition of licenses 203 . The voicemail mailbox message and prompt capacity supports 2
simultaneous connections and 15 hours of storage. This can be expanded up to 6 channels by the addition of
licenses, each of which enables an additional two channels and an additional 5 hours of storage.
·
WARNING
These cards should only be formatted using IP Office Manager or IP Office System Status Application. The cards
should only be removed from a system after either a card shut down 129 or a system shut down 131 .
Feature Key Dongle
SAP Code
IPO IP500 V2 SYS SD CARD A-LAW
700500924
IPO IP500 V2 SYS SD CARD MU-LAW
700500925
IPO IP500 V2 SYS SD CARD PARTNER
700500926
IPO IP500 V2 SYS SD CARD NORSTAR
700500927
· IP Office U-Law
A system fitted with this type of card will default to U-Law telephony. For pre-IP Office Release 7.0 software,
the system will default to IP Office standard mode. For IP Office Release 7.0+, the system will default to IP
Office Essential Edition - Quick Version mode Key System operation. Intended for North American locales.
· IP Office A-Law
A system fitted with this type of card will default to A-Law telephony. For pre-IP Office Release 7.0 software,
the system will default to IP Office standard mode. For IP Office Release 7.0+, the system will default to IP
Office Essential Edition - Quick Version mode PBX System operation. Intended for locales outside North
America.
· IP Office Partner Version
A system fitted with this type of card will default to U-Law telephony and IP Office Essential Edition PARTNER® Version mode Key System operation. Supported only in North American locales.
· IP Office Norstar Version
A system fitted with this type of card will default to A-Law telephony and IP Office Essential Edition - Norstar
Version mode Key System operation. Supported only in Middle East and North African locales.
· Avaya Branch Gateway
This type of SD card intended to be used with <%GATEWAY%> systems. The Avaya Branch Gateway System
SD card can only be used for Avaya Branch Gateway operation and cannot be used to change modes to IP
Office. You also cannot use or change an IP Office SD card for use with an Avaya Branch Gateway system.
Avaya Branch Gateway systems are not covered by this documentation.
PCM Encoding
· A-Law or Mu-Law
PCM (Pulse Code Modulation) is a method for encoding voice as data. In telephony, two methods PCM encoding are
widely used, A-law and Mu-law (also called U-law). Typically Mu-law is used in North America and a few other
locations while A-law by the rest of the world. As well as setting the correct PCM encoding for the region, the A-Law
or Mu-Law setting of an IP Office system when it is first started affects a wide range of regional defaults relating to
line settings and other values.
· For IP400 IP Office systems, each control units was manufactured as either an A-Law variant or a Mu-Law
variant.
· For IP500 and IP500v2 systems, the encoding default is set by the type of Feature Key installed when the
system is first started.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 156
15-601042 Issue 23f (20 April 2011)
System Components: Feature Keys
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 157
15-601042 Issue 23f (20 April 2011)
8.6 Mounting Kits
The following mounting kits are available for use with IP Office systems.
8.6.1 IP500 Wall Mounting Kits
IP500, IP500v2 control units and IP500 external expansion modules can be wall mounted. To do this, a wall mounting kit
is required in addition to suitable wall fixings. Wall mounting is not supported for IP400 external expansion modules.
In addition to the existing environmental requirements
apply when wall mounting a unit:
38
for an IP Office system, the following additional requirements
· The wall surface must be vertical, flat and vibration free. Attachment to temporary walls is not supported.
· Only the screws provided with the mounting kit should used to attach the brackets to the control unit.
The following wall mounting kits exist.
· IP500 Wall Mounting Kit V2 (SAP Code 700500923)
This kit can be used for wall mounting an IP500 or IP500 v2 control unit and IP500 external expansion modules.
This kit incorporates cable routing at the front and rear of the unit. For control units it allows orientation of the
control unit base card slots to the left or to the right.
· IP500 Wall Mounting Kit (SAP Code 700430150)
This old design of wall mounting kit can be used for wall mounting an IP500 or IP500v2 control units only. It does
not provide any cable routing and requires the control unit to be mounted with the base card slots to the right
only.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 158
15-601042 Issue 23f (20 April 2011)
System Components: Mounting Kits
8.6.2 IP500 Rack Mounting Kit
· IP500 Rack Mounting Kit (SAP 700429202)
This kit contains all the components required for the rack mounting of
a single IP500v2 control unit, IP500 control unit or IP500 external
expansion module. This includes screws for fixing of the brackets to
the module, bolts for securing the module in the rack and cable tidy
brackets.
8.6.3 IP400 Rack Mounting Kit
· IP400 Rack Mounting Kit (SAP 700210800)
This kit contains all the components required for the rack mounting of
a single control unit or expansion module. This includes screws for
fixing of the brackets to the module and bolts for securing the module
in the rack.
8.6.4 Barrier Box Rack Mounting Kit
· Barrier Box Rack Mounting Kit (SAP 700293905)
Barrier boxes must be used for out-of-building analog phone
extensions 25 . This bracket allows up to 8 IP Office barrier boxes to
be rack mounted and simplifies the number of connections to the
protective ground point in the rack. This kit must be used when more
than 3 barrier boxes are in use and supports a maximum of 16
barrier boxes for a single external expansion module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 159
15-601042 Issue 23f (20 April 2011)
8.7 Phones
IP Office Release 7.0 supports the following phones and phone add-ons. Availability may depend on location and may be
subject to local restrictions.
Digital Station (DS Port)
These digital stations connect to the IP Office via DS
Norstar Version mode.
· 1400 Series: 1403
· 9400 Series: 9404
· 9500 Series: 9504
161 ,
162 ,
164 ,
1408
9408
165 , 9508
164
1416
193
ports. The following are supported in IP Office Essential Edition -
163
165
Digital Station (TCM Port)
These digital stations connect to the IP500v2 IP Office system via TCM
Essential Edition - Norstar Version mode.
201
ports. The following are supported in IP Office
· 4100 Series: 4135, 4136, 4145, 4145EX, 4146, 4146EX - Connection to IP Office TCM ports via a Digital Mobility
Solution 180 system.
· 7400 Series: 7420, 7430, 7434, 7439, 7440, 7444, 7449 - Connection to IP Office TCM ports via a Digital Mobility
Solution 180 system.
· ACU: Audio Conferencing Unit 166
· M-Series: MT7100 167 , MT7100N 167 , MT7208 168 , MT7208N 168 , M7310 169 , M7310N 169 , M7324 170 , M7324N 170
.
· T-Series: T7000 171 , T7100 171 , T7208 172 , T7316 173 , T7316E 174 , T7406 175 , T7406E 175
Analog Telephones
Analog phones and devices connect to PHONE 198 ports with the IP Office system. However due to the variety of analog
phones and device available no guarantee of operation is given. It is the responsibility of the IP Office installer and
maintainer to test and verify the operation of proposed analog equipment.
· 6200 Series: 6211, 6219, 6221 (North America).
· Interquartz Gemini: 9330-AV, 9335-AV, 9281-AV (Europe, Middle East, Africa, Asia-Pacific).
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 160
15-601042 Issue 23f (20 April 2011)
System Components: Phones
8.7.1 1403
This phone is supported with IP Office Release 6.0 and higher.
1603
Feature
1403
Connects via
DS port.
IP Office Release
6.0
Programmable Buttons
3
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
Display
2 x 16 backlit.
Supported Add-Ons
None
Upgradeable Firmware
Fixed Telephony Function Keys
SPEAKER
MESSAGE
DROP
HEADSET
HOLD
REDIAL
VOLUME UP
MUTE
TRANSFER
CONFERENCE
Variant
1403 Telephone
CONTACTS
VOLUME DOWN
CALL LOG
MENU
SAP Code
Black
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
700469927
Page 161
15-601042 Issue 23f (20 April 2011)
8.7.2 1408
This phone is supported with IP Office Release 6 and higher.
1408
Feature
1408
Connects via
DS port.
IP Office Release
6.0+
Programmable Buttons
8
Headset Socket
Handsfree Speaker/Microphone
/
Message Waiting Lamp
Display
3 x 24
backlit.
Supported Add-Ons
None.
Upgradeable Firmware
Fixed Function Keys
SPEAKER
MESSAGE
DROP
HEADSET
HOLD
REDIAL
MUTE
TRANSFER
CONFERENCE
Variant
1408 Telephone
VOLUME UP
CONTACTS
VOLUME DOWN
CALL LOG
MENU
SAP Code
Black
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
700469851
Page 162
15-601042 Issue 23f (20 April 2011)
System Components: Phones
8.7.3 1416
This phone is supported with IP Office Release 6 and higher.
1416
Feature
1416
Connects via
DS port.
IP Office Release
6.0+
Programmable Buttons
16
Headset Socket
Handsfree Speaker/
Microphone
/
Message Waiting Lamp
Display
4 x 24 Backlit.
Supported Add-Ons
DBM32
177
x 3.
Upgradeable Firmware
Fixed Function Keys
SPEAKER
MESSAGE
DROP
HEADSET
MUTE
HOLD
REDIAL
TRANSFER
CONFERENCE
Variant
VOLUME UP
CONTACTS
VOLUME DOWN
CALL LOG
MENU
SAP Code
1416 Telephone
Black
700469869
DBM32 Button Module
Black
700469968
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 163
15-601042 Issue 23f (20 April 2011)
8.7.4 9404
9400 Series and 9500 Series phones are supported by IP Office Release 7.0 and higher. They are physically and
functionally the same, however the 9500 Series models are only supported with IP Office IP500v2 systems.
The phones provide 4 physical buttons with red and green LEDs. These can be used for up to 12 programmable features.
8.7.5 9408
9400 Series and 9500 Series phones are supported by IP Office Release 7.0 and higher. They are physically and
functionally the same, however the 9500 Series models are only supported with IP Office IP500v2 systems.
The phones provide 8 physical buttons with red and green LEDs. These can be used for up to 24 programmable features.
The phones support the addition of up to 3 BM12 button modules supporting an additional 24 programmable features
(using 12 buttons) per module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 164
15-601042 Issue 23f (20 April 2011)
System Components: Phones
8.7.6 9504
9400 Series and 9500 Series phones are supported by IP Office Release 7.0 and higher. They are physically and
functionally the same, however the 9500 Series models are only supported with IP Office IP500v2 systems.
The phones provide 4 physical buttons with red and green LEDs. These can be used for up to 12 programmable features.
8.7.7 9508
9400 Series and 9500 Series phones are supported by IP Office Release 7.0 and higher. They are physically and
functionally the same, however the 9500 Series models are only supported with IP Office IP500v2 systems.
The phones provide 8 physical buttons with red and green LEDs. These can be used for up to 24 programmable features.
The phones support the addition of up to 3 BM12 button modules supporting an additional 24 programmable features
(using 12 buttons) per module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 165
15-601042 Issue 23f (20 April 2011)
8.7.8 Audio Conferencing Unit
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
The Audio Conferencing Unit (ACU) is a multiple microphone desktop conferencing unit. The Audio Conferencing unit only
supports the following Feature codes:
· Speeddial: Feature 0
This feature code can be used to dial a stored number.
· If Feature 0 is followed by a 3-dight number in the range 000 to 255, the system directory entry with the
matching index is dialed.
· If Feature 0 is followed by * and a 2-digit number in the range 71 to 94, the personal directory entry with the
matching index is dialed.
· Hold/Switch Calls: Feature 2
This feature code will hold the current call. If there was already a call on hold, the feature code will switch between
calls.
· Conference: Feature 3
If the Audio Conferencing Unit has a call connected and another call on hold, using this feature code will conference
the unit and those calls.
· Last Number Redial: Feature 5
When the phone is idle, this feature code can be used to redial the last number dialed from the Audio Conferencing
Unit.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 166
15-601042 Issue 23f (20 April 2011)
System Components: Phones
8.7.9 M7100
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
8.7.10 M7100N
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 167
15-601042 Issue 23f (20 April 2011)
8.7.11 M7208
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
8.7.12 M7208N
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 168
15-601042 Issue 23f (20 April 2011)
System Components: Phones
8.7.13 M7310
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
8.7.14 M7310N
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 169
15-601042 Issue 23f (20 April 2011)
8.7.15 M7324
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
· Additional buttons can be supported on a M7324 phone through the addition of KLM button module
178 .
8.7.16 M7324N
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 170
15-601042 Issue 23f (20 April 2011)
System Components: Phones
8.7.17 T7000
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
The T7000 telephone is an entry-level digital set for basic low-use office environments. The T7000 is used primarily in the
EMEA (not available in North America).
8.7.18 T7100
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 171
15-601042 Issue 23f (20 April 2011)
8.7.19 T7208
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 172
15-601042 Issue 23f (20 April 2011)
System Components: Phones
8.7.20 T7316
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 173
15-601042 Issue 23f (20 April 2011)
8.7.21 T7316E
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
· Additional buttons can be supported on a T7316E phone through the addition of T7316E KEM
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
179
button modules.
Page 174
15-601042 Issue 23f (20 April 2011)
System Components: Phones
8.7.22 T7406, T7406e
Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500v2. They can be connected to
digital station ports provided by an IP500 TCM8 base card or on a DS16A/DS30A external expansion module.
These cordless phones use a base station that can support multiple sets. The T7406E base station supports up to 4
T7406E handsets. The T7406 base station supports up to 3 T7406 handsets. Each supported handset requires a
connection from the base station to a TCM port on the IP Office system.
Each phone is dedicated to its base station and cannot roam even if multiple base stations are installed.
The T7406E is available in North America, Mexico and Caribbean countries excluding Jamaica and Trinidad. The T7406E
replaces the discontinued T7406 cordless telephone.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 175
15-601042 Issue 23f (20 April 2011)
8.8 Phone Add-Ons
For IP Office Release 5.0 and higher, the maximum combined number of buttons on buttons modules per system is 1024.
T3 DSS modules are not included in the combined limits stated above but are limited to 30 T3 DSS modules (1080
buttons).
· BM12: +24 (Max 3 per phone, 32 per system.)
Add-on for 9408 and 9508 165 phones. Provides 12 buttons assignable in 2 pages for 24 features.
· DBM32 177 : +32 (Max 3 per phone, 32 per system.)
Add-on for the 1416 phones that provides two columns of 16 buttons. Up to 3 BM32 modules are supported with
any 4616. For IP Office 5.0, up to a maximum of 32 BM32 modules total are supported the IP Office system.
· KLM 178 : +48 (Max 2 per phone, 21 per system.)
Used with M7324 170 phones. Up to 2 buttons modules are supported per phone. Each button module provides 48
programmable buttons.
· T7316E KEM 179 : +24 (Max 9 per phone, 42 per system.)
Used with T7316E 174 phones. Each button module provides 24 programmable buttons.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 176
15-601042 Issue 23f (20 April 2011)
System Components: Phone Add-Ons
8.8.1 DBM32
The DBM32 add on provides an additional 32 twin-LED programmable buttons for 1416 phones. The units do not require
their own power supply connection as they draw power from the phone to which they are connected.
· Up to 3 units can be connected in a chain from a single 1416.
· Up to a maximum of 32 DBM32 units on the system.
Item
SAP Code
DBM32 BUTTON MODULE
700469968
Accessories
1600 SERIES BM32 CABLE - REPLACEMENT
700415581
1600 SERIES BM32 BOND BRIDGE - REPLACEMENT
700415599
1616/BM32 PLASTIC LABEL COVERS (20) – REPLACEMENT
700415672
1600 SERIES BM32 FLIP STAND - REPLACEMENT
700432800
Paper Labels
·
1616/BM32 PAPER DESI LABELS - PACKAGE OF 50 LABELS (8.5" x 11")
700415656
1616/BM32 PAPER DESI LABELS - PACKAGE OF 50 LABELS (A4)
700434236
Note for Australian installations only:
Installations of the 1416 terminal with an 1151 PSU and DBM32 must be restricted to the same building as the host
Gateway. That is, the 1416 – if installed with an 1151 PSU and DBM32 – cannot be connected in a campus
environment where the 1416 terminal is installed in a building separate from the building housing the Gateway.
This application cannot be used with exposed (out-of-building) wiring.
· For installations in which the 1416 is used without the 1151 PSU and DBM32, campus connections are
acceptable: the 1416 can be located in a separate building in these cases.
· This restriction applies to Australian installations only.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 177
15-601042 Issue 23f (20 April 2011)
8.8.2 KLM Module
This type of button module can be used with the M7324 170 phones to provide additional programmable buttons. For IP
Office Essential Edition - Norstar Version, only 1 module can be attached to each phone. Each module requires its own
power supply unit.
+01
+13
+25
+37
+02
+14
+26
+38
+03
+15
+27
+39
+04
+16
+28
+40
+05
+17
+29
+41
+06
+18
+30
+42
+07
+19
+31
+43
+08
+20
+32
+44
+09
+21
+33
+45
+10
+22
+34
+46
+11
+23
+35
+47
+12
+24
+36
+48
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 178
15-601042 Issue 23f (20 April 2011)
System Components: Phone Add-Ons
8.8.3 T7316e KEM
This type of button module can be used with the T7316E 174 phones to provide 24 additional programmable buttons. In IP
Office Essential Edition - Norstar Version, up to 4 modules can be added, allowing a total of 72 programmable buttons.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
+01
+13
+02
+14
+03
+15
+04
+16
+05
+17
+06
+18
+07
+19
+08
+20
+09
+21
+10
+22
+11
+23
+12
+24
Page 179
15-601042 Issue 23f (20 April 2011)
8.9 Ancilliary Systems
8.9.1 Digitial Mobility Solution
Avaya 4100 Series and 7400 Series phones are supported using a Digital Mobility Solution (DMS). This is a DECT system
that can be used to support up to 64 handsets. The DMS connects to the IP500 system using a TCM port for each
handset.
Digital Mobility 2.4 GHz solution - North America and CALA
7420 Handset
N7B80BK
7430 Handset
N7B80BLE6
7440 Handset
N7B80BQE6
Digital Mobility Base Station 10
2.4GHz, Compatible with Handset 7430/7440, Repeater 40.
N7B65KPE5
Digital Mobility Repeater 40
2.4GHz, Compatible with Handset 7430/7440, Base station 10. N7B80AGE5
Digital Mobility External Antenna 51
International.
N7B65KWE5
DMC 080 Digital Mobility Controller
North America.
N7B65KJE5
DMC 320 Digital Mobility Controller
North America.
N7B65KKE5
Digital Mobility 1.9 GHz solution - North America
7439 Handset
Replaces the 7430 model.
N7B80CLE6
7449 Handset
Replaces the 7430 model.
N7B80CNE6
Digital Mobility Base Station 19
North America.
N7B80CRE6
Digital Mobility Repeater 49
Canada, US.
N7B80CUE6
Digital Mobility External Antenna 51
International.
N7B65KWE5
DMC 080 Digital Mobility Controller
North America.
N7B65KJE5
DMC 320 Digital Mobility Controller
North America.
N7B65KKE5
Digital Mobility 1.8 GHz solution - Europe, Hong Kong, Australia, New Zealand
4135 Handset
Europe & Hong Kong
N7B80BME6
4145 Handset
Europe & Hong Kong
N7B80BRE6
4145EX Handset KIT - EU
Ruggedized version of 4145 - Europe & Hong Kong
N7B80BWE6
4136 Handset
Australia/New Zealand
N7B80CCE6
4146 Handset
Australia/New Zealand
N7B80CEE6
4146EX Handset
Ruggedized version of 4146 - Australia/New Zealand
N7B80CFE6
Digital Mobility Base Station 15
N7B65KTE5
Digital Mobility Repeater 25
N7B65KUE5
Digital Mobility Repeater 45
N7B80AHE5
Digital Mobility External Antenna 51
International
N7B65KWE5
DMC 081 Digital Mobility Controller
International
N7B80AAE5
DMC 321 Digital Mobility Controller
International
N7B80ABE5
Digital Mobility 1.8 GHz solution - South America
7434 (South America)
N7B80ACE6
7444 (South America)
N7B80ADE6
Digital Mobility Base Station 14
N7B80AEE6
Digital Mobility Repeater 24
N7B80AFE6
Digital Mobility External Antenna 51
International
N7B65KWE5
DMC 081 Digital Mobility Controller
International
N7B80AAE5
DMC 321 Digital Mobility Controller
International
N7B80ABE5
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 180
15-601042 Issue 23f (20 April 2011)
System Components: Ancilliary Systems
8.10 Applications
This section outlines the requirements for various IP Office applications. These are just outlines, for full details refer to the
specific installation manuals for those applications and to the IP Office Technical Bulletins.
8.10.1 Manager
This tool is used to access all parts of the IP Office configuration. Different levels of access can be defined to control which
parts of the configuration the Manager user can view and alter. Manager is also used to upgrade the software files used by
an IP Office system. When running is also acts as a TFTP server from which some Avaya phones can request new
software.
Note that IP Office Manager's software level is always two higher than the IP Office core software with which it is release.
For example IP Office 6.0 core software is release with IP Office Manager 8.0.
IP Office Manager is backwards compatible and can be used to manage IP Office systems running software from IP Office
2.1 upwards.
Details
DVD
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 1)
Languages
English, Brazilian, Dutch, French, German, Italian, Spanish (Mexican).
License
No license required.
PC Requirements
Minimum PC Requirements
Operating System Support
RAM
256MB
Server OS:
Hard Disk Free Space
1GB*
2003 Server
Processor:
2008 Server
- Pentium
PIII 800MHz
Client OS:
- Celeron
Celeron 3 800Mhz
XP Professional
- AMD
Athlon Opteron, Athlon64/XP
Vista
Additional Apps:
- .NET2
Windows 7
Installed with Manager if not
already present.
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
*Includes disk space required for .NET2 component.
Ports
Component
Location - %ProgramFiles%\Avaya\IP Office\
Ports
IP Office Manager
Manager\manager.exe
TCP Port 50802.
TCP Port 50804.
TCP Port 50812.
UDP Port 50798.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 181
15-601042 Issue 23f (20 April 2011)
8.10.2 Monitor
Monitor (also known as System Monitor) is a tool that can show all activity on the IP Office system in great detail. As a
consequence, interpretation of Monitor traces requires a high-level of data and telephony protocol knowledge. However, all
IP Office installers and maintainers must understand how to run Monitor when necessary as Avaya may request copies of
Monitor traces to resolve support issues.
For IP Office 4.0 and higher, the System Status Application
information than is provided by Monitor.
183
has been added to provide more easily interpreted
· Two versions of Monitor are included in the IP Office Admin applications suite, one for IP Office 4.0 systems and
one for pre-4.0 IP Office systems. Care should be taken to ensure that the correct version is used when monitoring
an IP Office system.
Details
DVD
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 1)
Languages
English only.
License
No license required.
PC Requirements
Minimum PC Requirements
Operating System Support
RAM
128MB
Server OS:
Hard Disk Free Space
10GB
2003 Server
Processor:
2008 Server
- Pentium
PIII 800MHz
Client OS:
- Celeron
Celeron 3 800Mhz
XP Professional
- AMD
Athlon B 650MHz
Vista
Windows 7
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
· Vista support is only on Business, Enterprise and Ultimate versions.
· Windows 7 support is only on Professional, Enterprise and Ultimate versions.
Ports
Component
Location - %ProgramFiles%\Avaya\IP Office\
Ports
System Monitor
Monitor\sysmonitor.exe
UDP 50794.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 182
15-601042 Issue 23f (20 April 2011)
System Components: Applications
8.10.3 System Status Application (SSA)
This tool provides a wide range of information about the current status of an IP Office 4.0 or higher system. Its includes
available resources and components within the system. This includes details of current call in progress. Details of the
number of alarms are recorded and the time date of the most recent alarms.
When required for diagnostics escalation SSA is able to take a snap shot image of the IP Office system's status including a
copy of its current configuration. Use of SSA requires an IP Office service user name and password that has been
configured for System Status access in the IP Office's security settings.
· For IP500v2 systems, SSA is pre-installed on the system's Avaya SD memory card and can be run by browsing to
the IP Office system's IP address.
Details
DVD
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 1)
License
No license required.
PC Requirements
Minimum PC Requirements
Operating System Support
RAM
256MB
Server OS:
Hard Disk Free Space
1.4GB
2003 Server
Processor:
2008 Server
- Pentium
PIII 800MHz
Client OS:
- Celeron
Celeron 3 800Mhz
XP Professional
- AMD
Athlon B 650MHz
Vista
Additional Apps:
Windows 7
- Sun Java Virtual
Machine
Installed with SSA if not already
present.
- Web Browser
· Internet Explorer 7+.
· Mozilla Firefox 3.0.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
Page 183
15-601042 Issue 23f (20 April 2011)
8.10.4 TAPI
IP Office TAPI is a client PC application that allows TAPI compliant applications to interact with the IP Office.
· 1st Party TAPI
In this unlicensed mode the TAPI software supports control of an individual user's associated extension, allowing a
TAPI compliant application to answer (requires a phone that supports handsfree answer) and make calls.
Details
DVD
IP Office Release 7.0 User/Admin DVD Set (2) (700500928) (Disk 1)
License
PC Requirements: 1st Party TAPI
Minimum PC Requirements
Operating System Support
RAM
64MB
Server OS:
Hard Disk Free Space
50MB
2003 Server
Processor:
2008 Server
- Pentium
PIII 800MHz
Client OS:
- Celeron
Celeron 3 800Mhz
XP Professional
- AMD
Athlon B 65-0MHz
Vista
Windows 7
· Vista support is only on Business,
Enterprise and Ultimate versions.
· Windows 7 support is only on
Professional, Enterprise and Ultimate
versions.
PC Requirements: 3rd Party TAPI
Minimum PC Requirements
Operating System Support
RAM
64MB
Server OS:
Hard Disk Free Space
50MB
2003 Server
Processor:
2008 Server
- Pentium
PIII 800MHz
Client OS:
- Celeron
Celeron 3 800Mhz
XP Professional
- AMD
Athlon B 65-0MHz
Vista
Windows 7
Ports
Component
Location - %ProgramFiles%\Avaya\IP Office\
Ports
TAPI2
TAPI\tspi2w.tsp
UDP 50797.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 184
15-601042 Issue 23f (20 April 2011)
System Components: Applications
8.10.5 IP Office Ports
Most PC firewalls will request the user to allow various exceptions when a newly installed application is first run. However
this may not always be the case, especially if the firewall is located elsewhere than the user's PC.
Adding Firewall Exceptions
The file avayafw.bat can be used to open up the necessary firewall exceptions for IP Office applications. The file can be
downloaded from http://marketingtools.avaya.com/knowledgebase/tools/firewall.
It only works for:
· The default Windows XP/Windows 2003 firewall.
· The application must be installed for the exception to be created.
· The application must be installed in the default location.
Whilst avayafw.bat only works subject to the conditions above, for other firewalls study of this file will indicate the
necessary application files and ports for which exceptions need to be created.
Ports Used
The list below details many of the IP ports used by IP Office control units and IP Office applications. Many of these are
standard ports for different IP traffic protocols.
Indicates a listening port on the IP Office control unit.
PC running an IP Office application.
indicates a port to which the IP Office sends, for example to a
* Indicates that the port and or protocol can be changed.
Port
Protocol
25*
SMTP
TCP
Email system alarms from the IP Office to SMTP server. For IP Office 4.2 also used
for Voicemail Email on Embedded Voicemail.
37
Time
UDP
Time requests from the IP Office to a Time Server (RFC868).
53
DNS
UDP
Domain Name Service responses.
67
BOOTP/DHCP
UDP
DHCP server operation.
68
BOOTP/DHCP
UDP
DHCP client operation.
69
TFTP
UDP
File requests to the IP Office.
69
TFTP
UDP
File requests by the IP Office.
80
HTTP
TCP
HTTP File requests.
161*
SNMP
UDP
From SNMP applications.
162*
SNMP Trap
UDP
To addresses set in the IP Office configuration.
500
IKE
UDP
Key exchange for IPSec protocol.
389*
LDAP
TCP
Lightweight Directory Access Protocol.
443
HTTPS
TCP
HTTPS communication with IP Office provisioned DECT, IP Office Softphone.
520
RIP
UDP
520
RIP
UDP
To and from the IP Office to other RIP devices. For RIP1 and RIP2 (RIP1
compatible) the destination address is a subnet broadcast, eg. 192.168.42.255.
For RIP2 Multicast the destination address is 224.0.0.9.
1701
L2TP
UDP
Layer 2 tunneling protocol.
1718
H.323
UDP
H.323 Discovery
1719
H.323 RAS
UDP
H.323 Status. VoIP device registering with the IP Office.
1720
H.323/H.245
UDP
H.323 Signalling. Data to a registered VoIP device.
UDP
PC Wallboard to CCC Wallboard Server.
2127
(UDP)
Function
3478
SIP
UDP
Port used for STUN requests from the IP Office to the SIP provider.
5005
RTCPMon
UDP
RTCP Monitoring information from Avaya H323 phones.
5060
SIP
UDP/
TCP*
SIP Line Signalling
8080
HTTP
TCP
Browser access to the Delta Server application.
8089
Enconf
UDP
From the IP Office to the Conferencing Center Server Service. User access to the
Conferencing Center is direct via HTTP sessions.
8888
HTTP
TCP
Browser access to the IP Office ContactStore (VRL) application.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 185
15-601042 Issue 23f (20 April 2011)
Port
Protocol
Function
49152
to
53247
*
RTP/RTCP
UDP
Dynamically allocated ports used during VoIP calls for RTP and RTCP traffic. The
port range can be adjusted through the System | Gatekeeper tab.
50791
IPO Voicemail
UDP
To voicemail server address.
50793
IPO Solo
Voicemail
UDP
From IP Office TAPI PC with Wave drive user support.
50794
IPO Monitor
UDP
From the IP Office Monitor application.
50795
IPO Voice
Networking
UDP
Small Community Network signalling (AVRIP) and BLF updates. Each system does
a broadcast every 30 seconds. BLF updates are sent required up a maximum of
every 0.5 seconds.
50796
IPO PCPartner UDP
From an IP Office application (for example Phone Manager or SoftConsole). Used
to initiate a session between the IP Office and the application.
50797
IPO TAPI
UDP
From an IP Office TAPI user PC.
50798
(UDP)
UDP
BT Fusion variant. No longer used.
50799
IPO BLF
UDP
Broadcast to the IP Office LAN and the first 10 IP addresses registered from other
subnets.
50800
IPO License
Dongle
UDP
To the License Server IP Address set in the IP Office configuration.
50801
EConf
UDP
Conferencing Center Service to IP Office.
50802
Discovery
TCP
IP Office discovery from Manager.
50804
*
Service Access TCP
Protocol
50805
*
TCP
50808
*
TCP
IP Office system status access.
50812
*
TCP
IP Office security settings access.
50813
*
TCP
IP Office configuration settings access.
" TLS Secure.
" TLS Secure.
· CDR/SMDR from the IP Office is sent to the port number and IP address defined during configuration and using either
TCP or UDP as selected.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 186
15-601042 Issue 23f (20 April 2011)
System Components: Applications
Ports
IP Office Monitor can be used to display IP packet details including the source and destination Port numbers. As well as
displaying the port numbers (in decimal), IP Office Monitor also displays the names of more commonly used ports
including IP Office specific ports.
For example "src = 23" is interpreted as "src = 23 (Telnet)".
The list below details the ports currently decoded by IP Office Monitor. For a full list of assigned non-IP Office ports see
http://www.iana.org/assignments/port-numbers.
· 20 File Transfer [Default Data]
· 156 SQL Service
· 21 File Transfer [Control]
· 161 SNMP
· 23 Telnet
· 162 SNMPTRAP
· 25 Simple Mail Transfer
· 179 Border Gateway Protocol
· 37 Time
· 1719 H.323Ras
· 43 Who Is
· 1720 H.323/H.245
· 53 Domain Name Server
· 50791 IPO Voicemail
· 67 Bootstrap Protocol Server
· 50792 IPO Network DTE
· 68 Bootstrap Protocol Client
· 50793 IPO Solo Voicemail (i.e. Wave driver for TAPI)
· 69 Trivial File Transfer
· 50794 IPO Monitor
· 70 Gopher
· 50795 IPO Voice Networking
· 79 Finger
· 50796 IPO PCPartner
· 80 World Wide Web-HTTP
· 50797 IPO TAPI
· 115 Simple File Transfer Protocol
· 50798 IPO Who-Is response
· 123 Network Time Protocol
· 50799 IPO BLF
· 137 NETBIOS Name Service
· 50800 IPO License Dongle
· 138 NETBIOS Datagram Service
· 50801 EConf
· 139 NETBIOS Session Service
Protocols
IP Office Monitor, as well as displaying the Protocol number (in decimal) of packets, also displays the names of the more
common Protocols. For example "pcol = 1" is decoded as "pcol = 1 (ICMP)".
Protocol numbers currently decoded by IP Office Monitor are:
· 1 - Internet Control Message [ICMP]
· 2 - Internet Group Management [IGMP]
· 6 - Transmission Control [TCP]
· 8 - Exterior Gateway Protocol [EGP]
· 9 - Interior Gateway Protocol [IGP]
· 17 - User Datagram [UDP]
· 41 - Ipv6 [IPV6]
· 46 - Reservation Protocol [RSVP]
· 47 - General Routing Encapsulation [GRE]
· 58 - ICMP for IPv6 [IPv6-ICMP]
· 111 - IPX in IP[IPX-In-IP]
· 115 - Layer Two Tunneling Protocol [L2TP]
· 121 - Simple Message Protocol [SMP]
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 187
15-601042 Issue 23f (20 April 2011)
8.11 Physical Ports
The following port types are found on IP Office systems:
· ANALOG 191
Used for the connection of external analog trunks.
· AUDIO 191
Used for input of an external music on hold source.
· BRI 192
Used for connection of BRI trunks (Quad BRI trunk card).
· DC I/P 193
Power input from external power supply unit.
· DS 193
Connection of Avaya digital station phones supported by IP Office.
· RS232/DTE 107
Used for control unit maintenance under Avaya guidance. On expansion modules not used.
· EXPANSION 195
Used for interconnection of external expansions modules and control units.
· EXT O/P 105
Used to control external relay systems. The port provides two switchable (on, off and pulse) controls.
·
Used for connection of functional or protective ground if required.
· LAN 196
10/100Mbps Ethernet LAN ports.
· PF 197
Analog power fails ports.
· PHONE 198 (POT) 198
Analog phone extension ports. On older units these ports are labeled as POT ports.
· PRI 199
PRI trunk ports.
· TCM 200
Connection for M-Series and T-Series phones supported by IP Office. Also for Digital Mobility Solution system
supporting 4100 Series and 7400 Series phones.
· USB
Not used.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 188
15-601042 Issue 23f (20 April 2011)
System Components: Physical Ports
8.11.1 Cables
The IP Office systems are designed primarily for use within an RJ45 structured cabling system using CAT3 unshielded
twisted-pair (UTP) cabling and RJ45 sockets.
A structured cabling system is one where cables are run from a central RJ45 patch panel in the communications/data room
to individual RJ45 sockets at user locations. All wires in each cable between the patch panel and the desk socket are
connected straight through. This arrangement allows devices connected at the patch panel to be swapped to match the
type of device that needs to be connected at the user socket. For example, making one user socket a phone port and
another user socket a computer LAN port, without requiring any rewiring of the cables between the patch panel and the
user location.
· Traditional IDC Punchdown Wiring Installations
Where necessary, the far end RJ45 plug can be stripped from IP Office cables and wired into traditional wiring
systems using punch-block connectors. This type of installation should be performed by an experienced wiring
technician.
· Trunk Connections
The majority of IP Office trunk ports use RJ45 connectors for acceptance of an RJ45-to-RJ45 cable. However,
connection at the line provider's end may require use of a different plug type in order to match the line providers
equipment.
· RJ11 Phone Connectors
Many phones use RJ11 sockets and are supplied with RJ11-to-RJ11 cables. RJ11 plugs can be inserted into RJ45
sockets and in many case the connection will work. However this is not recommended or supported as the
connection lock is not truly positive and may become disconnected. An RJ45-to-RJ11 cable 193 is available for these
connections.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 189
15-601042 Issue 23f (20 April 2011)
Standard IP Office Cables
The following are Avaya standard cables available for use with IP Office systems. The maximum length is applicable if the
standard Avaya cable is replaced with an alternate cable.
Cable
9-Way DTE Cable
107
Description
SAP Code
Standard
Length
Maximum
Length
Connects to control unit RS232 DTE port. 9Way D-type plug to 9-way D-type socket.
–
2m/6'6''.
2m/6'6''.
Structured Cabling DS Line
Cable 193
Connects from RJ45 sockets to RJ11 socketed TT700047871 4m/13'2''.
DS and analog phones.
See table
below.
BRI/PRI Trunk Cable
Connects BRI/PRI trunk ports to the line
700213440
provider's network termination point. RJ45 to
RJ45. Red.
3m/9'10''.
–
Expansion Interconnect
Cable 195
Connects the control unit to expansion
modules. RJ45 to RJ45. Blue.
700213457
1m/3'3''.
1m/3'3''.
LAN Cable
Connects from IP Office LAN ports to IP
devices. RJ45 to RJ45. Grey.
700213481
3m/9'10''.
100m/328'.
196
192
The table below details the maximum total cable distances for DS and analog extensions using different cable types.
Unshielded Twisted-Pair (UTP) - 50nf/Km
Telephone
CW1308
AWG22
(0.65mm)
AWG24
(0.5mm)
AWG26
(0.4mm)
1400 Series
1200m/3937'.
1000m/3280'.
670m/2200'.
400m/1310'.
9400/9500 Series
1200m/3937'.
1000m/3280'.
670m/2200'.
400m/1310'.
TCM (without power
booster)
–
305m/1000'
–
–
" (with power
booster)
–
790m/2600'
–
–
Analog Phones
1000m/3280'.
1000m/ 3280'.
400m/1640'.
800m/2620'.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 190
15-601042 Issue 23f (20 April 2011)
System Components: Physical Ports
8.11.2 ANALOG Port
These ports are analog trunk ports. The IP400 ATM4 analog trunk cards and IP500 analog trunk cards only support loopstart trunks. The ATM16 Analog Trunk module supports both loop-start and ground-start trunks, switchable within the IP
Office configuration.
ANALOG
Pin
Description
1
Not used.
2
Not used.
3
Not used.
4
Ring.
5
Tip.
6
Not used.
7
Not used.
8
Not used.
· Off-Hook Current: 25mA.
·
IMPORTANT
In all IP Office installations, any module being used for analog trunk connections must be connected to a functional
earth 24 .
·
WARNING
Within the Republic of South Africa and in areas of high lightning risk, any module using analog trunk connections
must be connected to a protective ground 24 and to surge protection equipment 25 .
8.11.3 AUDIO Port
This port is found on the rear of all IP Office control units. It is used for the input of an external music-on-hold sound
source. Note that if the IP Office has loaded an internal music-on-hold sound file, any input from this socket is ignored.
The port is a 3.5mm stereo jack socket suitable for use with the most standard audio leads and connection to the
'headphone' output socket of most audio systems.
The use of a 'headphone' socket allows simple volume adjustment. Connection via a 'Line Out' socket may require
additional equipment in order to adjust the volume level.
Pin No.
Description
Common
Common
Left
Audio In - Left Channel.
Right
Audio In - Right - Channel.
· Input impedance: 10k /channel. Maximum a.c. signal – 200mV rms.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 191
15-601042 Issue 23f (20 April 2011)
8.11.4 BRI Port (To)
These ports are BRI To interface ports for connection to external BRI trunk services. Note that BRI ports found on the
IP400 So8 module are BRI-S interface ports for connect to ISDN terminal devices, see BRI Port (So).
PRI/BRI Trunk Cable
This cable is used to connect from IP Office BRI/PRI trunk ports to the line providers network termination equipment. If
that equipment does not use RJ45 sockets, the cable may need to be stripped and rewired or an alternate cable used. The
appropriate signal pin-outs and wire colours are detailed below.
IP Office
BRI
Wire
RJ45
BRI
PRI
Network
Termination
PIN
1
–
Rx-A
White/Orange
1
2
–
Rx-B
Orange/White
2
3
Tx-A
White/Green
3
4
Rx-A
Tx-A
Blue/White
4
5
Rx-B
Tx-B
White/Blue
5
6
Tx-B
–
–
Green/White
6
7
–
–
White/Brown
7
8
–
–
Brown/White
8
RJ45
· Supply: BRI/PRI trunks cards are not supplied with these cables.
· Cable Color: Red.
· SAP Code: 700213440.
· Standard Length: 3m/9'10".
· Maximum Length: 5m/16'5''.
· Though not used pins 7 and 8 are through connected for ease of construction.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 192
15-601042 Issue 23f (20 April 2011)
System Components: Physical Ports
8.11.5 DC I/P Port
Found on all IP Office control units and expansion modules. Used for connection from the external power supply unit
supplied with the control unit or module.
19
· No other type of power supply unit should be used with the module or module unless specifically indicated by Avaya.
· Power cords must not be attached to the building surface or run through walls, ceilings, floors and similar openings.
8.11.6 DS Ports
These ports are used for connection from an RJ45 structured cabling system to digital station phones supported by the IP
Office. DS ports are provided by IP500 Digital Station Cards 142 , IP500 ATM Combination Cards 140 , IP500 BRI
Combination Cards 141 and IP500 Digital Station 149 external expansion modules.
Though the RJ11 to RJ11 cables supplied with some phones can be plugged directly into RJ45 ports including those on IP
Office modules, this is not recommend as the connection lock is not positive and may become disconnected.
DS ports on Digital Station V1/V2 expansion modules can be connected to out-of-building extensions 25 . If this is the
case, connection must be made via suitable protective devices at each end and via each building primary protection. In
addition the Digital Station module must be connected to a protective ground.
DS ports on IP Office control units must not be connected to out-of-building extensions.
Structured Cabling Line Cord
This is an RJ45 to RJ11 cable suitable for connection from a structured cabling system RJ45 port to a DS phone. It can also
be used for two-wire analog phone extensions.
This cable is not suitable for connection from an Avaya 1151D1/B2 power supply unit to a DS phone with a 4450, EU24 or
XM24 add-on module. In those cases the cables supplied with the power supply unit and the add-on module should be
used.
IP Office
DS Port
Phone
Pin
Description
Pin
1
Not used.
–
2
Not used.
1
3
Not used.
2
4
Signal 1.
3
5
Signal 2.
4
6
Not used.
5
7
Not used.
6
8
Not used.
–
Port
· SAP Code: T700047871.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 193
15-601042 Issue 23f (20 April 2011)
8.11.7 RS232 DTE Port
These ports are found on the rear of all IP Office control units and external expansion modules. The DTE ports on external
expansion modules are not used.
The RS232 DTE ports on the control units can be used for system maintenance and connection of serial terminal adaptors.
On IP400 control units the port can also be used for connection of the IP Office serial port licence key dongle.
An asynchronous terminal program such as HyperTerminal is also required. Configure this for operation via a PC serial
port, as follows:
Bits per second 38,400
Data bits 8
Parity None
Stop Bits 1
Flow Control None
Settings | Emulation TTY
DTE Cables
These cables are used for system maintenance and diagnostics under Avaya guidance. They can also be used for
connection of RS232 serial terminal adaptor equipment to the IP Office control unit. The cable required depends on the IP
Office control unit. This cable is a "Straight through DB9 female to DB9 male serial cable".
IP Office 9-Way RS232 Signal
DTE Port
PC/Terminal
Adaptor
3
Receive data
3
2
Transmit Data
2
7
RTS (Request To Send)
7
8
CTS (Clear To Send)
8
6
DSR (Data Set Ready)
6
5
Ground
5
1
DCD (Data Carrier Detect)
1
4
DTR (Data Terminal Ready)
4
9
RI (Ring Indicator)
9
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 194
15-601042 Issue 23f (20 April 2011)
System Components: Physical Ports
8.11.8 EXPANSION Port
This type of port is found on the rear of IP Office control units and external expansion modules. It is used for connecting
the external expansion modules to there parent IP Office control unit.
The connection between these ports should only be done using an Avaya Expansion Interconnect Cable. No other cable
type should be used.
· Each external expansion module is supplied with a blue 1 meter (3'3'') expansion interconnect cable. This
cable must be used when connecting to expansion ports on the rear of a control unit.
Expansion Interconnect Cable
The Expansion Interconnect cable is used to link expansion ports between the IP Office control unit and external expansion
modules.
· Supply: One cable is normally supplied with each external expansion module.
· SAP Code: 1m (3'3") Blue cable - 700213457, 2m (6'6") Yellow cable - 700472871.
8.11.9 EXT O/P Port
These ports are found on the rear of all IP Office control units. They are used for connection to external switching relays.
The port uses a standard 3.5mm stereo jack plug for connection.
The IP Office is able to open (high resistance), close (low resistance) or pulse (close for 5 seconds and then open) two
switches within the port. Either switch can be operated separately. These switches are intended for activation of external
relays in systems such as door opening systems.
· CAUTION: In installations where this port is connected to a device external to the building, connection must be via a
towerMAX SCL/8 Surge Protector and a protective ground connection must be provided on the IP Office control unit.
EXT O/P
Pin
Description
1
Switch 1.
2
Switch 2.
3
0 Volts (Ground/Chassis)
· Switching Capacity: 0.7A.
· Maximum Voltage: 55V d.c.
· On state resistance: 0.7 ohms.
· Short circuit current: 1A.
· Reverse circuit current capacity: 1.4A.
· Ensure that pins 1 and 2 are always at a positive voltage with respect to pin 3.
3.5mm stereo audio jack plugs are frequently sold as pre-wired sealed modules. It may be necessary to use a multi-meter
to determine the wiring connections from an available plug. Typically 3 (common to both relays) is the cable screen.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 195
15-601042 Issue 23f (20 April 2011)
8.11.10 LAN Port
These ports are found on IP Office control units. They are used for connection to IP LANs and IP devices.
All IP Office LAN ports are 10/100Mbps auto-sensing. Operation varies as follows:
· IP Office 500 / IP500v2
The WAN port is not supported on systems running in IP Office Essential Edition - Norstar Version mode.
The LEDs are used as follows:
· Green: On = connected, Flashing = Activity.
· Yellow: On = 100Mbps, Off = 10Mbps.
LAN Cables
These are CAT5 UTP cables for connection of various IP devices within the IP Office system.
IP Office
LAN
Pin
MDIX
(Normal)
MDI
(Crossover)
Wire
Standard/
Interconnect
Crossover
1
Rx-A.
Tx-A.
White/Orange
1
3
2
Rx-B.
Tx-B.
Orange/White
2
6
3
Tx-A.
Rx-A.
White/Green
3
1
4
Not used.
Not used.
Blue/White
4
4
5
Not used.
Not used.
White/Blue
5
5
6
Tx-B.
Rx-B.
Green/White
6
2
7
Not used.
Not used.
White/Brown
7
7
8
Not used.
Not used.
Brown/White
8
8
· SAP Code:
· LAN Cable - GREY: 700213481.
Standard straight LAN cable.
· LAN Crossover Cable - Black: 700213473.
LAN crossover cable.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 196
15-601042 Issue 23f (20 April 2011)
System Components: Physical Ports
8.11.11 PF Port
These ports are found on the rear of the IP400 Analog Trunk expansion module. They are analog extension ports that can
be used in conjunction with analog loop-start trunks during power failure to the IP Office system.
Any phones connected to these ports should be clearly labeled as power fail extensions in accordance with the appropriate
national and local regulatory requirements.
PF
Pin
Description
1
Not used.
2
Pin 2 is internally connected to pin 5 via a ringer capacitor.
3
Not used.
4
Ring.
5
Tip.
6
Pin 6 is internally connected to pin 5 via a ringer capacitor.
7
Not used.
8
Not used.
· Minimum Wire Size: AWG 26.
· Maximum Cable Length:
· AWG26: 500m / 1640'.
· AWG24, AWG22: 1000m / 3280'.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 197
15-601042 Issue 23f (20 April 2011)
8.11.12 PHONE (POT) Port
These ports are analog extension ports. On older IP Office units these ports were labeled as POT ports rather than PHONE
ports.
PHONE ports on Phone V1/V2 expansion modules can be connected to out-of-building extensions 25 . If this is the case,
connection must be made via suitable protective devices (IP Office Barrier Box) at each end and via each building primary
protection. In addition the Phone module must be connected to a protective ground.
PHONE ports on IP Office control units must not be connected to out-of-building extensions.
PHONE
Pin
Description
1
Not used.
2
Not used.
3
Not used.
4
Ring.
5
Tip.
6
Not used.
7
Not used.
8
Not used.
· REN: 2
· Off-Hook Current: 25mA.
· Ring Voltage: 40V rms.
· Minimum Wire Size: AWG 26.
· Maximum Cable Length:
· AWG26: 0.5km / 1640 feet.
· AWG24, AWG22: 1km / 3280 feet.
Except on some older equipment, these ports do not include a ringing capacitor. Therefore for connection to 4-wire analog
phones where this is a requirement (typically the United Kingdom and New Zealand), connection should be via a Master
socket containing ringing capacitors. On some older IP403 control units and IP400 Phone V1 modules, pins 2 and 6 are
internally connected via ringing capacitors.
Structured Cabling Line Cord
This is an RJ45 to RJ11 cable suitable for connection from a structured cabling system RJ45 port to a DS phone. It can also
be used for two-wire analog phone extensions.
IP Office
DS Port
Phone
Pin
Description
Pin
1
Not used.
–
2
Not used.
1
3
Not used.
2
4
Signal 1.
3
5
Signal 2.
4
6
Not used.
5
7
Not used.
6
8
Not used.
–
Port
· SAP Code: T700047871.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 198
15-601042 Issue 23f (20 April 2011)
System Components: Physical Ports
8.11.13 PRI Port
These ports are used for connection to PRI trunk services including E1, T1 and E1-R2.
PRI Trunk Cable
This cable is used to connect from IP Office PRI trunk ports to the line providers network termination equipment. If that
equipment does not use RJ45 sockets, the cable may need to be stripped and rewired or an alternate cable used. The
appropriate signal pin-outs and wire colours are detailed below.
IP Office
Wire
RJ45
PRI
Network Termination
PIN
1
Rx-A
White/Orange
1
2
Rx-B
Orange/White
2
3
White/Green
3
4
–
Tx-A
Blue/White
4
5
Tx-B
White/Blue
5
6
–
Green/White
6
7
–
White/Brown
7
8
–
Brown/White
8
RJ45
· Supply: PRI trunks cards are not supplied with these cables.
· Cable Color: Red.
· SAP Code: 700213440.
· Standard Length: 3m/9'10".
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 199
15-601042 Issue 23f (20 April 2011)
8.11.14 TCM Port (RJ21)
These ports are used for TCM extension ports in an IP500v2 system. They are found on IP500 Digital Station A 151
external expansion modules. These are supported by IP500v2 systems running IP Office Release 7.0 and higher.
They are used for supported M-Series and T-Series digital stations. They are also used for 4100 and 7400 Series phone
support by connection to a Digital Mobility Solution 180 system.
Cable lengths up to 305 m (1000 ft) using 0.5mm (24AWG) wires do not require a power booster. Lengths up to 790 m
(2600 ft) are supported if an auxiliary power supply booster is used.
1st RJ21 Connector
Port
1
Tip
Ring
2
Tip
Ring
3
Tip
Ring
4
Tip
Ring
5
Tip
Ring
6
Tip
Ring
7
Tip
Ring
8
Tip
Ring
9
Tip
Ring
10
11
12
13
14
15
16
Not Used
2nd RJ21 Connector
Pin
Wire
Port
26
White/Blue
1
1
Blue/White
27
White/Orange
2
Orange/White
28
White/Green
3
Green/White
29
White/Brown
4
Brown/White
30
White/Slate
5
Slate/White
31
Red/Blue
6
Blue/Red
32
Red/Orange
7
Orange/Red
33
Red/Green
8
Green/Red
34
Red/Brown
9
Brown/Red
Tip
35
Red/Slate
Ring
10
Slate/Red
Tip
36
Black/Blue
Ring
11
Blue/Black
Tip
37
Black/Orange
Ring
12
Orange/Black
Tip
38
Black/Green
Ring
13
Green/Black
Tip
39
Black/Brown
Ring
14
Brown/Black
Tip
40
Black/Slate
Ring
15
Slate/Black
Tip
41
Ring
Tip
Ring
2
Tip
Ring
3
Tip
Ring
4
Tip
Ring
5
Tip
Ring
6
Tip
Ring
7
Tip
Ring
8
Tip
Ring
9
Tip
Ring
Wire
26
White/Blue
1
Blue/White
27
White/Orange
2
Orange/White
28
White/Green
3
Green/White
29
White/Brown
4
Brown/White
30
White/Slate
5
Slate/White
31
Red/Blue
6
Blue/Red
32
Red/Orange
7
Orange/Red
33
Red/Green
8
Green/Red
34
Red/Brown
9
Brown/Red
Tip
35
Red/Slate
Ring
10
Slate/Red
Tip
36
Black/Blue
Ring
11
Blue/Black
Tip
37
Black/Orange
Ring
12
Orange/Black
Tip
38
Black/Green
Ring
13
Green/Black
Tip
39
Black/Brown
Ring
14
Brown/Black
40
Black/Slate
15
Slate/Black
Yellow/Blue
41
Yellow/Blue
16
Blue/Yellow
16
Blue/Yellow
42
Yellow/Orange
42
Yellow/Orange
17
Orange/Yellow
17
Orange/Yellow
43
Violet/Slate
43
Violet/Slate
08
Slate/Violet
08
Slate/Violet
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
10
Pin
11
12
13
14
Not Used
Page 200
15-601042 Issue 23f (20 April 2011)
System Components: Physical Ports
8.11.15 TCM Port (RJ45)
These ports are used for TCM extension ports in an IP500v2 system. They are found on IP500 TCM8 Digital Station Cards
143 . These are supported by IP500v2 systems running IP Office Release 7.0 and higher.
They are used for supported M-Series and T-Series digital stations. They are also used for 4100 and 7400 Series phone
support by connection to a Digital Mobility Solution 180 system.
Though the RJ11 to RJ11 cables supplied with some phones can be plugged directly into RJ45 ports including those on IP
Office modules, this is not recommend as the connection lock is not positive and may become disconnected.
Cable lengths up to 305 m (1000 ft) using 0.5mm (24AWG) wires do not require a power booster. Lengths up to 790 m
(2600 ft) are supported if an auxiliary power supply booster is used.
Structured Cabling Line Cord
This is an RJ45 to RJ11 cable suitable for connection from a structured cabling system RJ45 port to a TCM phone. It can
also be used for two-wire analog phone extensions.
IP Office
DS Port
Phone
Pin
Description
Pin
1
Not used.
–
2
Not used.
1
3
Not used.
2
4
Signal 1.
3
5
Signal 2.
4
6
Not used.
5
7
Not used.
6
8
Not used.
–
Port
· SAP Code: T700047871.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 201
15-601042 Issue 23f (20 April 2011)
8.12 Licences
Various IP Office features and applications require entry of license keys into the system's configuration. The license keys
are unique 32-character codes based on the feature being activated and the serial number of the feature key dongle 156
installed with the IP Office system.
The serial number is printed on the feature key dongle and prefixed with FK. It can also be viewed in the system
configuration using IP Office Manager.
· For IP500v2 systems, the feature key dongle takes the form of an SD card inserted into the control unit. The card is
a mandatory item for these systems even if they use no licensed features.
When a license key is entered into the IP Office configuration, the following information is shown.
· Status
The status, which is Unknown until the configuration file is sent back to the IP Office system.
· Unknown
This status is shown for licenses that have just been added to the configuration shown in IP Office Manager.
Once the configuration has been sent back to the IP Office and then reloaded, the status will change to one of
those below.
· Valid
The features licensed can be configured and used.
· Invalid
The license was not recognized. It did not match the serial number of the Feature Key.
· Dormant
The license is valid but is conditional on some other pre-requisite licenses.
· Obsolete
The license is valid but is one no longer used by the level of software running on the IP Office system.
· Expired
The license has gone past its expiry date.
· License
The name of the licensed feature. This may differ from the ordered RFA name.
· Instances
Depending on the license, this may be the number of ports enabled or number of simultaneous users of the
licensed feature. Sometime the number of instances is specified in the license name.
· Expires
Most purchased licenses have no expiry setting. For some features, trial licenses may be available which will have
an expiry date.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 202
15-601042 Issue 23f (20 April 2011)
System Components: Licences
8.12.1 System Edition Licenses
These license are used to set what range of features the IP Office system supports.
Essential Edition Additional
Voicemail Ports :
IPO LIC R6 ESSNTL EDDITION ADD 2 - 229423.
For IP500v2 only. Unlicensed, the embedded voicemail provided by the system supports 2 simultaneous connections and
15 hours of storage. This can be expanded up to 6 channels by the addition of licenses, each of which enables an
additional two channels. For IP Office Release7.0+ each license also enables an additional 5 hours of storage.
Upgrade Licenses
Existing IP Office systems being upgraded to IP Office Release 6.0 or higher may require a software upgrade license.
· New IP500v2 Systems
For the first 90 days, a new IP500v2 control unit will run any supported IP Office Release without requiring an
upgrade license. The highest level run is written into the system's memory (not the SD card) and that becomes a
permanent entitlement for the control unit. However, after 90 days the IP500v2 will require an upgrade license if
upgraded to a software release higher than any that it has run in the initial 90 day period.
·
Warning
Systems upgraded without the appropriate license will display "No license available" and will not allow any
telephony functions.
·
Software Upgrade
Existing IP Office systems being upgraded to IP Office Release 6.0 or higher require an upgrade license. This applies
to all IP Office system modes, for example IP Office standard mode, IP Office Standard Version, IP Office Essential
Edition - PARTNER® Version, IP Office Essential Edition - Norstar Version and IP Office Essential Edition - Quick
Version modes. There are two types of upgrade licenses as follows:
IPO LIC UPG R7.0 SML - 262645.
· Small System Upgrade Licenses:
This license can be used to upgrade systems with up to 32 users and no external expansion modules.
· Large System Upgrade Licenses:
IPO LIC UPG R7.0 - 262644.
This license can be used to upgrade system with more than 32 users or with external expansion modules.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 203
15-601042 Issue 23f (20 April 2011)
8.12.2 Trunk Licensing
The following trunks licenses can be used by a IP Office Essential Edition - Norstar Version mode system.
·
IP500 Universal PRI (Additional channels)
These licenses are used to enable additional B-channels above the basic 8 on an IP500 PRI-U card. The IP500 PRI-U
card supports E1, T1 and E1-R2 PRI modes. The IP Office system supports 8 unlicensed B-channels on each IP500
PRI-U port fitted. Additional B-channels, up to the capacity of ports installed and PRI mode selected require
licenses. These additional channels consume the licenses based on which additional channels are configured as inservice from port 9 of slot 1 upwards. D-channels are not affected by licensing.
·
IP500 T1 CHANNELS ADD 2CH - 215180.
IP500 T1 CHANNELS ADD 8CH - 215181.
·
IP500 T1 CHANNELS ADD 32CH - 215182.
·
·
IP500 E1 CHANNELS ADD 2CH - 215183.
IP500 E1 CHANNELS ADD 8CH - 215184.
·
·
IP500 E1 CHANNELS ADD 22CH - 215185.
·
IP500 E1R2 CHANNELS ADD 2CH - 215186.
IP500 E1R2 CHANNELS ADD 8CH - 215187.
·
·
IP500 E1R2 CHANNELS ADD 22CH - 215188.
·
SIP Trunk Channels
These licenses are used to configure the maximum number of simultaneous SIP trunk calls supported. A IP Office
Essential Edition - Norstar Version mode system supports 3 channels without licenses.
·
IPO LIC SIP TRNK RFA 1 - 202967.
IPO LIC SIP TRNK RFA 5 - 202968.
·
·
IPO LIC SIP TRNK RFA 10 - 202969.
IPO LIC SIP TRNK RFA 20 - 202970.
·
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 204
15-601042 Issue 23f (20 April 2011)
System Components: Licences
8.12.3 User Licenses
· Mobile Worker Profile License
By default only 3 users can be configured to use remote forwarding/mobile twinning features. Additional users can
be enabled by the addition of Mobile Worker licenses to the configuration.
·
·
·
·
IPO
IPO
IPO
IPO
LIC
LIC
LIC
LIC
R6
R6
R6
R6
MOBILE
MOBILE
MOBILE
MOBILE
WORKER
WORKER
WORKER
WORKER
1 - 229434.
5 - 229435.
20 - 229436.
5 TRIAL - 229437.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 205
15-601042 Issue 23f (20 April 2011)
8.12.4 Trial Licenses
The following trial licenses can be requested. A trial license is valid for 60 days from the date of issue and can only be
issued once for a particular IP Office Feature Key serial number. Apart from those restrictions, the trial license works the
same as a full license.
· Mobile Worker (5 Users):
IPO LIC R6 MOBILE WORKER 5 TRIAL - 229437.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 206
15-601042 Issue 23f (20 April 2011)
System Components: Licences
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 207
15-601042 Issue 23f (20 April 2011)
Chapter 9.
Safety Statements
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 209
15-601042 Issue 23f (20 April 2011)
9. Safety Statements
The Avaya IP400 Office and IP500 Office modules are intended to be installed by 'Service Personnel' and it is the
responsibility of the Service Personnel to ensure that all subsidiary interconnected equipment is wired correctly and also
meet the safety requirements of IEC60950 or UL60950 where applicable.
·
The CE mark affixed to this equipment means that the module complies with the 1999/5/EC (R&TTE), 89/336/EEC
(EMC) and 72/23EEC (LVD) Directives.
· The Declarations of Conformity (DoC) for the IP400 and IP500 products are available on the IP Office Application
DVD.
·
This warning symbol is found on the base of IP500 modules.
· Refer to Trunk Interface Modules
which country.
211
for information concerning which Trunk Interface module variants are fitted in
In Finland, Norway and Sweden a protective earthing conductor must be attached to the protective earth point on the rear
of the IPO500 and IPO500v2 Servers. See Grounding 73 for more information. In addition the Server must be located in a
restricted access location where equipotential bonding has been applied, for example, in a telecommunication centre.
9.1 Lithium Batteries
A lithium battery is fitted to the real time clock on IP Office IP400 control unit motherboards and the IP500 control unit
motherboard. .
WARNING
The Lithium battery must only be replaced by Avaya personnel or authorized representatives. There is a danger of
explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's instructions.
9.2 Lightning Protection/Hazard Symbols
Lightning protectors
The buildings lightning protectors must be verified as follow:
1. Check the lightning protectors, at the trunk cable entry point to the building housing the Avaya IP Office, paying
special attention to the lightning protection grounding. Report any problems, in writing, to the telephone company.
2. Equipment that is designed to be connected using internal wiring is typically not lightning protected. Hence, Avaya
IP Office extension cabling must not leave the building. For installations where telephones and/or other standard
(tip/ring) devices are installed in another building then lightning protection is required (see Out of Building
Telephone Installations 25 ).
Hazard Symbol
The shock hazard symbol is intended to alert personnel to electrical hazard or equipment damage. The following
precautions must also be observed when installing telephone equipment:
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the
network interface.
4. Always use caution when working with telephone lines.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 210
15-601042 Issue 23f (20 April 2011)
Safety Statements: Lightning Protection/Hazard Symbols
9.3 Trunk Interface Modules
To ensure the validation of the approvals, only the following types of trunk interface cards must be fitted in the following
IP Office control units.
USA/Canada
Product
Quad
BRI
PRI E1
Single
Dual
PRI T1
Single
ATM4
Dual
IP500v2
IP500
Rest of World
Product
Quad
BRI
PRI E1/E1R2
Single
Dual
PRI T1
Single
ATM4
Dual
IP500v2
IP500
Notes
· E1R2 trunks are only supported in CALA and Korea.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 211
15-601042 Issue 23f (20 April 2011)
9.4 Further Information and Product Updates
Further information, including Product and Reference Manual updates, can be obtained from Avaya Dealers and
Distributors or from Avaya's web site: http://www.avaya.com.
This guide is also available from the Avaya's support web site: http://support.avaya.com.
Support Telephone Numbers
For initial help and support, contact your distributor/supplier. The following contact points are for Avaya authorized
partners.
· In the USA only
Avaya provides a toll-tree Customer Helpline 24 hours a day:
· Name: Avaya Technical Support Organization (TSO)
· Customer Helpline: 1 800 628-2888
· Address: 8744 Lucent Blvd., Highlands Ranch, Colorado, 80129 USA
· URL: http://support.avaya.com
If you need assistance when installing, programming, or using your system, call the Helpline or your Avaya
representative. Consultation charges may apply.
· Outside the USA
If you need assistance when installing, programming, or using your system, contact your Avaya representative.
· URL: http://support.avaya.com
9.5 Port Safety Classification
The Avaya IP Office systems have the following ports which are classified as follows:
Port Name
Port Description
Port Classification
PRI port
PRI ISDN connection (NET)
TNV (Operating within the limits of SELV)
BRI ports
BRI ISDN connection (NET)
TNV (Operating within the limits of SELV)
Analog ports
Two wire analog trunk
TNV3
Power fail ports
Two wire analog trunk
TNV3
DTE port
Async Data connection.
SELV
Analog Telephone Ports
Telephone Extension ports
TNV2
Digital Telephone Ports
Telephone Extension ports
SELV
LAN ports
10/100 BaseT attachment to LAN.
SELV
Expansion ports
Expansion Module connector.
SELV
Audio port
Connector for Music on Hold.
SELV
External Control port
Connector for Controlling Ancillary
circuits.
SELV
DC Input port
Connector for DC input power.
SELV
Interconnection circuits shall be selected to provide continued conformance with the requirements of EN 609050:1992/
A3:1995 clause 2.3 for SELV circuits and with the requirements of clause 6 for TNV circuits, after connections between
equipment.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 212
15-601042 Issue 23f (20 April 2011)
Safety Statements: Port Safety Classification
9.6 EMC Directive
889/336/ EEC (EMC Directive) CISPR 22:1993 including A1 + A2, AS/NZ 3548:1995 (ROW)
·
WARNING
This is a class A product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his or her own expense.
Canadian Department of Communications (DOC)
''NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was
performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does
not imply that Industry Canada approved the equipment."
EMC Caution for China
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 213
15-601042 Issue 23f (20 April 2011)
9.7 Regulatory Instructions for Use
9.7.1 Australia
Connection
Connection of IP400 Office products must be via a Line Isolation Module with a telecommunications compliance label.
BRI Interface
During the configuration, ensure "000" emergency number is not barred, by performing the following:
· Short Code: 000
· Telephone No: 000;
· Function: DialEmergency
Connections to TS013, the following Bearer Capabilities shall not be used:
· 7kHz Audio, Video, Restricted Digital Information.
If unknown type of number is used in calling party number, the network will use the default CLI.
The system must be configured for Point to Multi point connection to comply with Austel requirements for connecting to
TS013 circuits.
As the IP Office does not support emergency dialing after loss of power, the following warning notice should be
recognized:
· WARNING
This equipment will be inoperable when mains power fails.
PRI Interface
During the configuration, ensure "000" emergency number is not barred, by performing the following:
· Short Code: 000
· Telephone No: 000;
· Function: DialEmergency
· WARNING
This equipment will be inoperable during mains power failure.
9.7.2 Canada
This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by
the registration number. The abbreviation, IC, before the registration number signifies that registration was performed
based on a Declaration of Conformity indicating that Industry Canada technical specifications were met.
It does not imply that Industry Canada approved the equipment.
''NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 1. The REN assigned to each terminal
equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface.
The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of
the Ringer Equivalence Numbers of all the devices does not exceed five.''
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 214
15-601042 Issue 23f (20 April 2011)
Safety Statements: Regulatory Instructions for Use
9.7.3 China
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 215
15-601042 Issue 23f (20 April 2011)
9.7.4 European Union
1. 999 and 112 calls must not be barred. Doing so will invalidate the approval.
2. All connections at the MDF shall be identifiable by suitable labeling.
3. The CE mark displayed on IP Office equipment indicates the systems compliance with the EMC, LVD, and R&TTE
Directives and common technical regulations for Primary Rate and Basic Rate ISDN.
4. All ports for the connection of other non-telecommunications apparatus have a Safety Extra Low Voltage (SELV) safety
status.
9.7.5 New Zealand
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item
complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom,
nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all
respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is
compatible with all of Telecom's network services.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 216
15-601042 Issue 23f (20 April 2011)
Safety Statements: Regulatory Instructions for Use
9.7.6 FCC Notification
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council on
Terminal Attachments (ACTA). On the rear of this equipment is a label that contains, among other information, a product
identifier in the format US:AAAEQ##TXXX. If requested, this number must be provided to the telephone company.
The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the
telephone line may result in devices not ringing in response to an incoming call. In most, but not all areas, the sum of
RENs should not exceed 5.0. To be certain of the number of devices that may be connected to a line, as determined by the
total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is
part of the product identifier that has the format US:AAAEQ##TXXX. The digits represented by ## are the REN without a
decimal point (for example, 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
Means of Connection
Connection of this equipment to the telephone network is shown in the following table.
Port
FIC
SOC
USOC Jack
REN
IPO500 PRI 1U,
IPO500 PRI2U,
IP400 PRI-T1
04DU9.BN,
04DU9.DN,
04DU9.IKN,
04DU9.ISN
6.0Y
RJ48C
NA
IPO500 ATM4U
IP400 ATM4U
OL13A, OL13B,
OL13C, 02AC2,
02LA2, 02LB2, 02LC2,
02LR2, 02LS2
9.0Y
RJ45S
0.1B
IPO500 ATM16
OL13A, OL13B,
OL13C,
02AC2, 02GS2,
02LA2, 02LB2, 02LC2,
02LR2, 02LF2
02GS2, 02LS2
9.0Y
RJ45S
0.1B
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is
necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the
operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please contact the Technical Service
Center at 1-800-242- 2121 or contact your local Avaya representative. If the equipment is causing harm to the telephone
network, the telephone company may request that you disconnect the equipment until the problem is resolved.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the
applicable FCC Part 68 rules and requirements adopted by the ACTA.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service
commission or corporation commission for information.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 217
15-601042 Issue 23f (20 April 2011)
Equipment With Direct Inward Dialing (“DID”):
Allowing this equipment to be operated in such a manner as to not provide proper answer supervision is a violation of Part
68 of the FCC’s rules.
Proper Answer Supervision is when:
A.This equipment returns answer supervision to the public switched telephone network (PSTN) when DID calls are:
· answered by the called station,
· answered by the attendant,
· routed to a recorded announcement that can be administered by the customer premises equipment (CPE) user.
· Routed to a dial prompt
B.This equipment returns answer supervision signals on all (DID) calls forwarded back to the PSTN.
Permissible exceptions are:
· A call is unanswered.
· A busy tone is received.
· A reorder tone is received.
Avaya attests that this registered equipment is capable of providing users access to interstate providers of operator
services through the use of access codes. Modification of this equipment by call aggregators to block access dialing codes
is a violation of the Telephone Operator Consumers Act of 1990.
Automatic Dialers:
When programming emergency numbers and (or) making test calls to emergency numbers:
1. Remain on the line and briefly explain to the dispatcher the reason for the call.
2. Perform such activities in the off-peak hours, such as early morning or late evenings.
Toll Restriction and Least Cost Routing Equipment:
The software contained in this equipment to allow user access to the network must be upgraded to recognize newly
established network area codes and exchange codes as they are placed into service.
Failure to upgrade the premises systems or peripheral equipment to recognize the new codes as they are established will
restrict the customer and the customer’s employees from gaining access to the network and to these codes.
FCC Part 68 Supplier’s Declarations of Conformity
Avaya Inc. in the United States of America hereby certifies that the equipment described in this document and bearing a
TIA TSB-168 label identification number complies with the FCC’s Rules and Regulations 47 CFR Part 68, and the
Administrative Council on Terminal Attachments (ACTA) adopted technical criteria.
Avaya further asserts that Avaya handset-equipped terminal equipment described in this document complies with
Paragraph 68.316 of the FCC Rules and Regulations defining Hearing Aid Compatibility and is deemed compatible with
hearing aids.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 218
15-601042 Issue 23f (20 April 2011)
Safety Statements: Regulatory Instructions for Use
9.7.7 Compliance with FCC Rules
Transmit and Receive Gain Settings for PRI/T1 and Analog Ports
The Gain settings are password controlled for use by qualified installation personnel only and must not be made available
to the end user. The default gain settings of 0dB ensures compliance with FCC part 68 section 68.308(b)(5) and TIA/EIAIS-968 Section 4.5.2.5. "Through transmission amplification from ports for the connection of separately registered
equipment or from other network connection ports". Gain setting adjustment by unqualified personnel may result in
violation of the FCC rules. Qualified personnel may adjust gain settings above these levels only where:
1. Measurement is made to ensure that the power levels sent to line at each network interface connected does not
exceed the maximum levels specified in FCC part 68 section 68.308(b) and TIA/EIA-IS-968 Section 4.5 for that
specific interface type.
2. Where gain adjustment away from the default values are made, precautions should be taken to ensure that the
connection of terminal equipment is controlled by qualified installation personnel.
3. To conform with the Receive Objective Loudness Rating at distances greater than 2.7km from the central office, on
analog trunks a receive gain of 1.5dB must be set.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 219
15-601042 Issue 23f (20 April 2011)
Index
Index
A
Analog
Phone Barrier Boxes 103
Phone Region Availability 29, 160
Port 188, 191
Application
Call Logging 32
CD/DVD 32
Maintenance 32
Manager 181
Monitor 182
System Status Application 183
TAPI 184
User 32
Voicemail 32
Audio
Port 188
Audio Port 191
Availability of Equipment 7
B
Backup
SD Card 121
Barrier Boxes
Analog Phone 103
Rack Mounting 104
Base Card
Analog Phone 14, 137
Digital Station 14, 137
Legacy Card Carrier 14, 137
VCM 14, 137
Batteries
Lithium 210
BRI
(Trunk) Port 192
Port 188
Buttons
Call appearance 82
Intercom 82
Line appearance 82
Programmable 82
C
Cable
Access Requirements 39
Clearance Requirements 39
Cables
Maximum Cable Distances 22, 189
Standard IP Office 22, 189
Cabling
Lightening Protection 25, 101
Call appearance buttons 82
Call Logging Application 32
Call Status
Application 32
Calls
External 82
Internal 82
Cards
IP500 Analog Phone Base 139
IP500 Digital Station Base 142
Conference Center
Application 32
Configuration
Create New 60
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Erase 108
Connections
Grounding 24
Out of Building 25, 101
ContactStore
Application 32
Control Unit
Rack Mounting 26
Wall Mounting 26
Copy
SD Card 123
Country
Languages 31
Supported Locales 31
Create Configuration 60
D
Daughter Cards
Analog Trunk 16, 145
BRI Trunk 16, 146
PRI Trunk 147
PRI-U Trunk 16
Trunk 16
DC I/P
Port 188
DCI I/P Port 193
DECT
Phone 29, 160
Region Availability 29, 160
DS
IROB 102
Phone 29, 102, 160
Port 188, 193
Region Availablility 29, 160
DTE Port 107
Cable requirement 107, 194
RS232 107, 194
Settings 107, 194
E
Embedded Voicemail
Application 32
EMC Cautions
Canadian Department of Communications 213
EMC Caution for China 213
Federal Communications Commission 213
Envirmental Requirements 38
Equipment Availability 7
Expansion
Port 188
Expansion Modules
IP400 Analog Trunk 17
IP400 Digital Station 17
IP400 Phone 17
IP400 So8 17
IP400 WAN3 17
IP500 Digital Station 17, 149
IP500 Phone 17, 154
IPO 500 Analog Trunk 17
IPO 500 BRI So8 17
Expansion Port 195
EXT O/P
Port 188
EXT O/P Port 105, 195
External calls 82
External Expansion Modules 17
Page 221
15-601042 Issue 23f (20 April 2011)
TAPI 184
Licenses
PC-Base 28
PC-Less 28
Lightening Portection 210
Lightening Protection 25, 101
Line appearance buttons 82
Lithium Batteries 210
F
Faulty Units 7
FCC Rules 219
Feature Key Server
Application 32
Feature Keys
Parallel 28
Serial 28
Smart Card 28
USB 28
Firewall Exceptiong 185
M
G
General Information
Training Courses 34
Web Sites 34
Grounding Control Units 24
H
H323
Phones 29, 160
Region Availability 29, 160
Hazard Symbols 210
Hazardous Substances 7
Homologation Statement 210
I
Intercom buttons 82
Internal calls 82
IP Office Operation in
Australia 214
Canada 214
China 215
European Union 216
New Zealand 216
USA 217
IP500
Analog Phone Base Card 14, 137
Analog Trunk Daughter Card 16
BRI Trunk Daughter Card 16
Digital Station Base Card 14, 137
Legacy Card Carrier Base Card 14, 137
PRI-U Trunk Daughter Card 16
Reset Button 106
Trunk Daughter Card 16
VCM Base Card 14, 137
IP500 Installation
Admin Applications 47
Card 62
Check Card LED 76
Connect Manager 49
Documentation 56
Grounding 73
Rack Mounting 69
Start Manager 50
Tools 55
Unpacking 57
K
Key Mode 82
L
LAN
Port 188
LAN Port 196
Licences
Manager 181
Monitor 182
Syatem Status Application
183
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Maintenance
Applications 32
Manager
Application 32
Components 181
License Requirements 181
PC Requirements 181
Upgrade Software 97
Memory card
Removal 93, 114, 129
Mode
Key 82
PBX 82
Modules
Trunk Interface 211
Monitor
Application 32
Components 182
License Requirements 182
PC Requirements 182
Protocols 185
MS-CRM
Application 32
N
New Configuration 60
O
Out of Building
Connections
25, 101
P
Parallel Feature Key 28
PBX Mode 82
PC-Base Licensing 28
PC-Less Licensing 28
PF
Port 188
PF Port 197
Phone (POT)
Port 188
Phone (POT) Port 198
Phone Manager
Application 32
Port
Analog 188, 191
Assigned 185
Audio 188, 191
BRI 188
BRI (Trunk) 192
DC I/P 188
DCI I/P 193
Door 105
DS 188, 193
Expansion 188, 195
EXT O/P 105, 188, 195
IP Office 185
LAN 188, 196
PF 188, 197
Page 222
15-601042 Issue 23f (20 April 2011)
Index
Port
Phone (POT) 188, 198
PRI 188, 199
RS232/DTE 188
RS323 DTE 107, 194
Safety Classification 212
USB 188
Used 185
WAN 188
Power Supplies
1151C1 19
1151C2 19
Cords 20
Type 40w PSU 19
Type 45W Earthed PSU 19
Type 60W Earthed PSU 19
Uninterrupted Power Supply 21
PRI
Port 188
PRI Port 199
Programmable buttons 82
Protocols 185
Locales 31
System Status
Application 32
System Status Application
Components 183
License Requirements 183
PC Requirements 183
R
Voicemail Lite
Application
VoiceMail Pro
Application
Rack Mounting Control Units 26
Region Availability
Analog Phone 29, 160
DECT Phone 29, 160
DS Phone 29, 160
H323 Phone 29, 160
Remove
SD Card 93, 114, 129
Requirements
Cable Access 39
Cable Clearance 39
Enviromental 38
Space 39
Wall Mounting 38
Restore
SD Card 122
RoHS 7
RS232/DTE
Port 188
T
TAPI
Components 184
License Requirements 184
PC Requirements 184
TAPILink Lite
Application 32
Training Courses 34
Trunk Interface Modules 211
U
USB
Feature Key
Port 188
28
V
32
32
W
Wall Mounting Control Units 26
Wall Mounting Requirements 38
WAN
Port 188
Web Sites 34
S
Safety Statement 210
SD Card
Backup 121
Copy 123
Removal 93, 114, 129
Restore 122
Security Settings
Default 110
Serial Feature Key 28
Smart card Feature Key 28
SNMP MIBs
Application 32
SoftConsole
Application 32
Software
Erase Core Software 111
Space Requirements 39
Statement
Homologation 210
Safety 210
Supported
Language 31
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 223
15-601042 Issue 23f (20 April 2011)
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 225
15-601042 Issue 23f (20 April 2011)
Performance figures and data quoted in this document are typical, and must be
specifically confirmed in writing by Avaya before they become applicable to any
particular order or contract. The company reserves the right to make alterations
or amendments to the detailed specifications at its discretion. The publication of
information in this document does not imply freedom from patent or other
protective rights of Avaya or others.
All trademarks identified by the ® or ™ are registered trademarks or trademarks,
respectively, of Avaya Inc. All other trademarks are the property of their
respective owners.
This document contains proprietary information of Avaya and is not to be
disclosed or used except in accordance with applicable agreements.
© 2011 Avaya Inc. All rights reserved.
IP Office Essential Edition - Norstar Version Installation
IP Office 7.0
Page 226
15-601042 Issue 23f (20 April 2011)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement