WAFER-BT_UMN_v1.01
WAFER-BT
WAFER-BT CPU Card
MODEL:
WAFER-BT
3.5” S BC with In te l® 22n m Ato m ™/Ce le ro n ® o n -b o a rd S o C,
VGA/LVDS /iDP, Du a l P CIe Gb E, US B 3.0, P CIe Min i,
S ATA 3Gb /s , m S ATA, COM, Au d io a n d Ro HS
Us e r Ma n u a l
Page I
Re v. 1.01 - 4 De c e m b e r, 2014
WAFER-BT
Re vis io n
Date
Version
Changes
4 December, 2014
1.01
Update Section 3.2.23: USB connectors pinouts
7 July, 2014
1.00
Initial release
Page II
WAFER-BT
Co p yrig h t
COP YRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page III
WAFER-BT
Ta b le o f Co n te n ts
1 INTRODUCTION.......................................................................................................... 1
1.1 INTRODUCTION........................................................................................................... 2
1.2 MODEL VARIATIONS ................................................................................................... 2
1.3 FEATURES ................................................................................................................... 3
1.4 CONNECTORS ............................................................................................................. 4
1.5 DIMENSIONS ............................................................................................................... 5
1.6 DATA FLOW ................................................................................................................ 6
1.7 TECHNICAL SPECIFICATIONS ...................................................................................... 7
2 UNPACKING ............................................................................................................... 10
2.1 ANTI-STATIC PRECAUTIONS .......................................................................................11
2.2 UNPACKING PRECAUTIONS ........................................................................................11
2.3 PACKING LIST........................................................................................................... 12
2.4 OPTIONAL ITEMS ...................................................................................................... 13
3 CONNECTORS ........................................................................................................... 14
3.1 PERIPHERAL INTERFACE CONNECTORS ..................................................................... 15
3.1.1 WAFER-BT Layout ........................................................................................... 15
3.1.2 Peripheral Interface Connectors ..................................................................... 15
3.1.3 External Interface Panel Connectors............................................................... 17
3.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 17
3.2.1 +12V DC-IN Power Connector ....................................................................... 17
3.2.2 Audio Connector .............................................................................................. 18
3.2.3 Battery Connector ............................................................................................ 19
3.2.4 Buzzer Connector ............................................................................................. 20
3.2.5 CPU Fan Connector ........................................................................................ 21
3.2.6 DDR3L SO-DIMM Slot .................................................................................... 21
3.2.7 Digital I/O Connector ...................................................................................... 22
3.2.8 Display Port Connector ................................................................................... 23
3.2.9 Front Panel Connector .................................................................................... 24
3.2.10 iRIS-1010 module slot .................................................................................... 25
Page IV
WAFER-BT
3.2.11 Keyboard and Mouse Connector .................................................................... 25
3.2.12 LVDS Backlight Inverter Connector .............................................................. 26
3.2.13 LVDS LCD Connector ................................................................................... 27
3.2.14 LAN LED Connector ...................................................................................... 28
3.2.15 PCIe Mini Card Slot ...................................................................................... 29
3.2.16 Power Button Connector................................................................................ 30
3.2.17 Reset Button Connector ................................................................................. 31
3.2.18 RS-232 Serial Port Connectors ...................................................................... 31
3.2.19 RS-422/485 Serial Port Connector ................................................................ 32
3.2.20 SATA 3Gb/s Drive Connector ........................................................................ 33
3.2.21 SATA Power Connector .................................................................................. 34
3.2.22 SMBUS Connector ......................................................................................... 35
3.2.23 USB Connectors ............................................................................................. 35
3.3 EXTERNAL PERIPHERAL INTERFACE CONNECTOR PANEL ......................................... 36
3.3.1 LAN Connector ................................................................................................ 37
3.3.2 USB Connectors ............................................................................................... 38
3.3.3 RS-232 Serial Port Connector ......................................................................... 38
3.3.4 VGA Connector ................................................................................................ 39
4 INSTALLATION ......................................................................................................... 41
4.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 42
4.2 INSTALLATION CONSIDERATIONS .............................................................................. 42
4.3 SO-DIMM INSTALLATION ....................................................................................... 44
4.4 SYSTEM CONFIGURATION ......................................................................................... 45
4.4.1 AT/ATX Mode Select Switch ............................................................................. 45
4.4.2 Clear CMOS Button ......................................................................................... 46
4.4.3 LVDS Panel Resolution Selection .................................................................... 46
4.4.4 LVDS Voltage Selection.................................................................................... 48
4.4.5 Flash Descriptor Security Override Jumper.................................................... 49
4.5 INTERNAL PERIPHERAL DEVICE CONNECTIONS ........................................................ 50
4.5.1 Audio Kit Installation ....................................................................................... 50
4.5.2 SATA Drive Connection ................................................................................... 51
4.5.3 Single RS-232 Cable ........................................................................................ 52
4.6 EXTERNAL PERIPHERAL INTERFACE CONNECTION ................................................... 53
4.6.1 LAN Connection ............................................................................................... 54
Page V
WAFER-BT
4.6.2 Serial Device Connection ................................................................................ 55
4.6.3 USB Connection ............................................................................................... 55
4.6.4 VGA Monitor Connection ................................................................................ 56
5 BIOS .............................................................................................................................. 58
5.1 INTRODUCTION......................................................................................................... 59
5.1.1 Starting Setup ................................................................................................... 59
5.1.2 Using Setup ...................................................................................................... 59
5.1.3 Getting Help ..................................................................................................... 60
5.1.4 Unable to Reboot after Configuration Changes .............................................. 60
5.1.5 BIOS Menu Bar ................................................................................................ 60
5.2 MAIN ........................................................................................................................ 61
5.3 ADVANCED ............................................................................................................... 62
5.3.1 ACPI Settings ................................................................................................... 63
5.3.2 Super IO Configuration ................................................................................... 64
5.3.2.1 Serial Port n Configuration ....................................................................... 64
5.3.3 Hardware Monitor ........................................................................................... 68
5.3.3.1 Smart Fan Mode Configuration ................................................................ 69
5.3.4 RTC Wake Settings ........................................................................................... 72
5.3.5 Serial Port Console Redirection ...................................................................... 73
5.3.5.1 Console Redirection Settings .................................................................... 74
5.3.6 CPU Configuration .......................................................................................... 77
5.3.7 IDE Configuration ........................................................................................... 78
5.3.8 USB Configuration........................................................................................... 79
5.4 CHIPSET ................................................................................................................... 80
5.4.1 North Bridge Configuration ............................................................................. 81
5.4.1.1 Intel IGD Configuration ............................................................................ 82
5.4.2 Southbridge Configuration .............................................................................. 83
5.4.2.1 PCI Express Configuration ....................................................................... 85
5.5 SECURITY ................................................................................................................. 86
5.6 BOOT........................................................................................................................ 87
5.7 EXIT ......................................................................................................................... 89
A BIOS MENU OPTIONS ............................................................................................. 91
B TERMINOLOGY........................................................................................................ 94
Page VI
WAFER-BT
C HAZARDOUS MATERIALS DISCLOSURE ......................................................... 99
C.1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 100
Page VII
WAFER-BT
Lis t o f Fig u re s
Figure 1-1: WAFER-BT ...................................................................................................................2
Figure 1-2: Connectors ..................................................................................................................4
Figure 1-3: Dimensions (mm) ........................................................................................................5
Figure 1-4: Data Flow Diagram ......................................................................................................6
Figure 3-1: Connector and Jumper Locations (Front) ..............................................................15
Figure 3-2: +12V DC-IN Power Connector Location ..................................................................18
Figure 3-3: Audio Connector Location .......................................................................................19
Figure 3-4: Battery Connector Location .....................................................................................20
Figure 3-5: Buzzer Connector Location .....................................................................................20
Figure 3-6: CPU Fan Connector Locations ................................................................................21
Figure 3-7: DDR3L SO-DIMM Slot Location ...............................................................................22
Figure 3-8: Digital I/O Connector Location ................................................................................22
Figure 3-9: Display Port Connector Location ............................................................................23
Figure 3-10: Front Panel Connector Location ...........................................................................24
Figure 3-11: iRIS-1010 Module Slot Location ............................................................................25
Figure 3-12: Keyboard and Mouse Location ..............................................................................26
Figure 3-13: Backlight Inverter Connector Location .................................................................27
Figure 3-14: LVDS Connector Location......................................................................................28
Figure 3-15: LAN LED Connector Location ...............................................................................29
Figure 3-16: PCIe Mini Card Slot Location .................................................................................30
Figure 3-17: Power Button Connector Location ........................................................................30
Figure 3-18: Reset Button Connector Location .........................................................................31
Figure 3-19: RS-232 Serial Port Connectors Locations ............................................................32
Figure 3-20: RS-422/485 Connector Location ............................................................................33
Figure 3-21: SATA 3Gb/s Drive Connectors Locations ............................................................34
Figure 3-22: SATA Power Connector Location .........................................................................34
Figure 3-23: SMBUS Connectors Location ................................................................................35
Figure 3-24: USB Connectors Locations....................................................................................36
Figure 3-25: External Peripheral Interface Connector ..............................................................37
Figure 3-26: LAN Connector ........................................................................................................37
Figure 3-27: RS-232 Serial Port Connector ................................................................................39
Page VIII
WAFER-BT
Figure 3-28: VGA Connector .......................................................................................................39
Figure 4-1: SO-DIMM Installation ................................................................................................44
Figure 4-2: AT/ATX Mode Select Switch Location ....................................................................46
Figure 4-3: Clear CMOS Button Location ...................................................................................46
Figure 4-4: LVDS Panel Resolution Selection Switch Location ..............................................48
Figure 4-5: LVDS Voltage Selection Jumper Location .............................................................49
Figure 4-6: Flash Descriptor Security Override Jumper Location ..........................................50
Figure 4-7: Audio Kit Cable Connection.....................................................................................51
Figure 4-8: SATA Drive Cable Connection .................................................................................52
Figure 4-9: Single RS-232 Cable Installation .............................................................................53
Figure 4-10: LAN Connection ......................................................................................................54
Figure 4-11: Serial Device Connector .........................................................................................55
Figure 4-12: USB Connector ........................................................................................................56
Figure 4-13: VGA Connector .......................................................................................................57
Page IX
WAFER-BT
Lis t o f Ta b le s
Table 1-1: WAFER-BT Model Variations .......................................................................................2
Table 1-2: Technical Specifications ..............................................................................................9
Table 3-1: Peripheral Interface Connectors ...............................................................................16
Table 3-2: Rear Panel Connectors ..............................................................................................17
Table 3-3: +12V DC-IN Power Connector Pinouts .....................................................................18
Table 3-4: Audio Connector Pinouts ..........................................................................................19
Table 3-5: Battery Connector Pinouts ........................................................................................20
Table 3-6: Buzzer Connector Pinouts .........................................................................................21
Table 3-7: CPU Fan Connector Pinouts .....................................................................................21
Table 3-8: Digital I/O Connector Pinouts ....................................................................................23
Table 3-9: Display Port Connector Pinouts ...............................................................................24
Table 3-10: Front Panel Connector Pinouts ...............................................................................25
Table 3-11: Keyboard and Mouse Connector Pinouts ..............................................................26
Table 3-12: Backlight Inverter Connector Pinouts ....................................................................27
Table 3-13: LVDS Connector Pinouts .........................................................................................28
Table 3-14: LAN LED Connector Pinouts ...................................................................................29
Table 3-15: Power Button Connector Pinouts ...........................................................................31
Table 3-16: Reset Button Connector Pinouts ............................................................................31
Table 3-17: RS-232 Serial Port Connector Pinouts ...................................................................32
Table 3-18: RS-422/485 Connector Pinouts ...............................................................................33
Table 3-19: DB-9 RS-422/485 Pinouts .........................................................................................33
Table 3-20: SATA Power Connector Pinouts .............................................................................35
Table 3-21: SMBUS Connectors Pinouts ...................................................................................35
Table 3-22: USB Connector Pinouts ...........................................................................................36
Table 3-23: LAN Pinouts ..............................................................................................................37
Table 3-24: Connector LEDs ........................................................................................................38
Table 3-25: USB 2.0 Port Pinouts ................................................................................................38
Table 3-26: USB 3.0 Port Pinouts ................................................................................................38
Table 3-27: RS-232 Serial Port Connector Pinouts ...................................................................39
Table 3-28: VGA Connector Pinouts ...........................................................................................40
Table 4-1: AT/ATX Mode Select Switch Settings .......................................................................45
Page X
WAFER-BT
Table 4-2: Clear CMOS Button Settings .....................................................................................46
Table 4-3: LVDS Panel Resolution Selection .............................................................................47
Table 4-4: LVDS Voltage Selection Jumper Settings ................................................................48
Table 4-5: Flash Descriptor Security Override Jumper Settings .............................................49
Table 5-1: BIOS Navigation Keys ................................................................................................60
Page XI
WAFER-BT
Lis t o f BIOS Me n u s
BIOS Menu 1: Main .......................................................................................................................61
BIOS Menu 2: Advanced ..............................................................................................................62
BIOS Menu 3: ACPI Configuration ..............................................................................................63
BIOS Menu 4: Super IO Configuration........................................................................................64
BIOS Menu 5: Serial Port n Configuration Menu .......................................................................64
BIOS Menu 6: Hardware Monitor.................................................................................................69
BIOS Menu 7: Smart Fan Mode Configuration ..........................................................................70
BIOS Menu 8: RTC Wake Settings ..............................................................................................72
BIOS Menu 9: Serial Port Console Redirection .........................................................................74
BIOS Menu 10: Console Redirection Settings ...........................................................................75
BIOS Menu 11: CPU Configuration .............................................................................................77
BIOS Menu 12: IDE Configuration ...............................................................................................78
BIOS Menu 13: USB Configuration .............................................................................................79
BIOS Menu 14: Chipset ................................................................................................................81
BIOS Menu 15: Northbridge Chipset Configuration ..................................................................81
BIOS Menu 16: Integrated Graphics ...........................................................................................82
BIOS Menu 17: Southbridge Chipset Configuration .................................................................84
BIOS Menu 18: Console Redirection Settings ...........................................................................85
BIOS Menu 19: Security ...............................................................................................................86
BIOS Menu 20: Boot .....................................................................................................................87
BIOS Menu 21:Exit ........................................................................................................................89
Page XII
WAFER-BT
Chapter
1
1 In tro d u c tio n
Page 1
WAFER-BT
1.1 In tro d u c tio n
Figure 1-1: WAFER-BT
The WAFER-BT SBC motherboard is an Intel® Atom™/Celeron® processor platform. It
supports one 204-pin 1066/1333 MHz single-channel DDR3L SO-DIMM supports up to
8GB (J1900, N2930, E3845, E3827, E3826) or 4GB (N2807, E3825, E3815).
The WAFER-BT includes a VGA connector, a LVDS connector and an iDP connector.
Expansion and I/O include one USB 2.0 connector and one USB 3.0 connector on the rear
panel, four USB 2.0 connectors by pin header and two SATA 3Gb/s connectors. Serial
device connectivity is provided by two internal RS-232 connectors, one external RS-232
connector and one internal RS-422/485 connector. Two RJ-45 Ethernet connectors
provide the system with smooth connections to an external LAN.
1.2 Mo d e l Va ria tio n s
The model variations of the WAFER-BT Series are listed below.
Mo d e l No .
SoC
WAFER-BT-i1-J19001-R10
Intel® Celeron® quad-core J1900 (10W)
WAFER-BT-i1-N29301-R10
Intel® Celeron® quad-core N2930 (7.5W)
WAFER-BT-i1-N28071-R10
Intel® Celeron® dual-core N2807 (4.3W)
WAFER-BT-i1-E38XX1-R10
Intel® Atom™ E38XX
Table 1-1: WAFER-BT Model Variations
Page 2
WAFER-BT
1.3 Fe a tu re s
Some of the WAFER-BT motherboard features are listed below:

3.5" SBC supports Intel® 22nm Atom™/Celeron® on-board SoC

Dual independent display support

One 204-pin 1066/1333 MHz single-channel DDR3L SO-DIMM supports up to
8GB (J1900, N2930, E3845, E3827, E3826) or 4GB (N2807, E3825, E3815)

COM, USB 3.0, SATA 3Gb/s, PCIE mini, mSATA and Audio support

IEI one key recovery solution allows you to create rapid OS backup and
recovery
Page 3
WAFER-BT
1.4 Co n n e c to rs
The connectors on the WAFER-BT are shown in the figure below.
Figure 1-2: Connectors
Page 4
WAFER-BT
1.5 Dim e n s io n s
The dimensions of the board are listed below:
Figure 1-3: Dimensions (mm)
Page 5
WAFER-BT
1.6 Da ta Flow
Figure 1-4 shows the data flow between the system chipset, the CPU and other
components installed on the motherboard.
Figure 1-4: Data Flow Diagram
Page 6
WAFER-BT
1.7 Te c h n ic a l Sp e c ific a tio n s
WAFER-BT technical specifications are listed below.
S p e c ific a tio n
WAFER-BT
SoC
Intel® Atom™ E3845 on-board SoC (1.91GHz, quad-core,
2MB cache, TDP=10W)
Intel® Atom™ E3827 on-board SoC (1.75GHz, dual-core,
1MB cache, TDP=8W)
Intel® Atom™ E3826 on-board SoC (1.46GHz, dual-core,
1MB cache, TDP=7W)
Intel® Atom™ E3825 on-board SoC (1.33GHz, dual-core,
1MB cache, TDP=6W)
Intel® Atom™ E3815 on-board SoC (1.46GHz, single-core,
512KB cache, TDP=5W)
Intel® Celeron® J1900 on-board SoC (2GHz, quad-core,
2MB cache, TDP=10W)
Intel® Celeron® N2930 on-board SoC (1.83GHz, quad-core,
2MB cache, TDP=7.5W)
Intel® Celeron® N2807 on-board SoC (1.58GHz, dual-core,
2MB cache, TDP=4.3W)
BIOS
AMI UEFI BIOS
Me m o ry
One 204-pin 1066/1333 MHz single-channel DDR3L
SO-DIMM supports up to 8GB (J1900, N2930, E3845, E3827,
E3826) or 4GB (N2807, E3825, E3815)
Gra p h ic s
Intel® HD Graphics Gen 7 Engines with 4 execution unit,
supports DX11.1, OpenGL 4.2 and OpenCL1.2
Dis p la y Ou tp u t
Dual Independent Display
1 x VGA (Resolution: [email protected])
1 x 24-bit dual-channel LVDS connector ([email protected])
1 x iDP interface for HDMI, LVDS, VGA, DVI, DP (up to
[email protected] Hz)
Page 7
WAFER-BT
S p e c ific a tio n
WAFER-BT
Eth e rn e t
1 x PCIe GbE by Intel I210 controller (LAN1)
1 x PCIe GbE by Intel I211 controller (LAN2)
S u p e r IO
Fintek F81866
Em b e d d e d Co n tro lle r
ITE IT8528E
Au d io
Realtek ALC662 HD codec
Wa tc h d o g Tim e r
Software programmable support 1~255 sec. system reset
I/O In te rfa c e
Au d io Co n n e c to r
1 x Analog audio by 10-pin (2x5) header
Eth e rn e t
Two RJ-45 ports
KB/MS
1 x PS/2 KB/MS
S e ria l P o rts
1 x RS-422/485 (by pin header)
3 x RS-232 (1 on rear I/O, 2 by pin header)
US B P o rts
1 x USB 3.0 (on rear I/O)
5 x USB 2.0 (1 on rear I/O, 4 by pin header)
Fro n t P a n e l
1 x 6-pin (1x6) wafer for power LED & HDD LED
1 x 2-pin (1x2) wafer for power button
1 x 2-pin (1x2) wafer for power reset button
LAN LED
2 x 2-pin header for LAN1 Link LED, LAN2 Link LED
FAN
1 x 4-pin CPU fan connector
1 x 4-pin system fan connector
S MBu s
1 x 4-pin (1x4) wafer
Exp a n s io n
1 x Full-size PCIe Mini card slot with mSATA support (SATA2
and mSATA share SATA signal)
iRIS Re m o te Ma n a g e m e n t
1 x iRIS-1010 slot
Mo d u le
Dig ita l I/O
S to ra g e
Page 8
8-bit digital I/O (4-bit input, 4-bit output)
WAFER-BT
S p e c ific a tio n
WAFER-BT
S e ria l ATA
2 x SATA 3Gb/s with 5V SATA power connector (no RAID)
En viro n m e n ta l a n d P o we r S p e c ific a tio n s
P o we r S u p p ly
12V DC input only (AT/ATX support)
P o we r Co n s u m p tio n
[email protected] (Intel® Celeron® J1900 CPU, 1 x 8GB 1333
MHz DDR3 memory)
Op e ra tin g Te m p e ra tu re
-20°C ~ 60°C
S to ra g e Te m p e ra tu re
-30°C ~ 70°C
Hu m id ity
5% ~ 95%, non-condensing
P h ys ic a l S p e c ific a tio n s
Dim e n s io n s
146mm x 102mm
We ig h t GW/NW
600 g / 250 g
Table 1-2: Technical Specifications
Page 9
WAFER-BT
Chapter
2
2 Un p a c kin g
P a g e 10
WAFER-BT
2.1 An ti-s ta tic P re c a u tio n s
WARNING!
Static electricity can destroy certain electronics. Make sure to follow the
ESD precautions to prevent damage to the product, and injury to the
user.
Make sure to adhere to the following guidelines:

Wear an anti-static wristband: Wearing an anti-static wristband can prevent
electrostatic discharge.

Self-grounding: Touch a grounded conductor every few minutes to discharge
any excess static buildup.

Use an anti-static pad: When configuring any circuit board, place it on an
anti-static mat.

Only handle the edges of the PCB: Don't touch the surface of the
motherboard. Hold the motherboard by the edges when handling.
2.2 Un pa c kin g P re c a u tio n s
When the WAFER-BT is unpacked, please do the following:

Follow the antistatic guidelines above.

Make sure the packing box is facing upwards when opening.

Make sure all the packing list items are present.
P a g e 11
WAFER-BT
2.3 P a c kin g Lis t
NOTE:
If any of the components listed in the checklist below are missing, do not
proceed with the installation. Contact the IEI reseller or vendor the
WAFER-BT was purchased from or contact an IEI sales representative
directly by sending an email to [email protected]
The WAFER-BT is shipped with the following components:
Qu a n tity
1
Ite m a n d P a rt Nu m b e r
1 x WAFER-BT single board computer with
specific heat sink
1
Audio cable
(P/N: 32000-072100-RS)
1
SATA with 5V output cable kit
(P/N: 32801-000201-100-RS)
1
Power cable
(P/N: 32100-087100-RS)
1
RS-232 cable
(P/N: 32205-002700-100-RS)
P a g e 12
Im a g e
WAFER-BT
1
Utility CD
1
One Key Recovery CD
1
Quick Installation Guide
2.4 Op tio n a l Ite m s
The following are optional components which may be separately purchased:
Ite m a n d P a rt Nu m b e r
Im a g e
Dual-port USB cable without bracket
(P/N: 32000-070301-RS)
RS-422/485 cable
(P/N: 32205-003800-300-RS)
PS/2 KB/MS Y-cable without bracket
(P/N: 32006-000300-100-RS)
P a g e 13
WAFER-BT
Chapter
3
3 Co n n e c to rs
P a g e 14
WAFER-BT
3.1 P e rip h e ra l In te rfa c e Co n n e c to rs
This chapter details all the jumpers and connectors.
3.1.1 WAFER-BT La yo u t
The figures below show all the connectors and jumpers.
Figure 3-1: Connector and Jumper Locations (Front)
3.1.2 P e rip h e ra l In te rfa c e Co n n e c to rs
The table below lists all the connectors on the board.
Co n n e c to r
Typ e
La b e l
+12V DC-IN power connector
4-pin Molex
CN5
Audio connector
10-pin header
AUDIO1
P a g e 15
WAFER-BT
Battery connector
2-pin wafer
BAT1
Buzzer connector
2-pin wafer
SP1
CPU fan connector
4-pin wafer
CPU_FAN1
System fan connector
4-pin wafer
SYS_FAN1
DDR3L SO-DIMM slot
DDR3L SO-DIMM slot
DIMM1
Digital I/O connector
10-pin header
DIO1
Display port connector
20-pin header
DP1
Front panel connector
6-pin wafer
CN4
iRIS-1010 module slot
iRIS-1010 module slot
IPMI1
Keyboard & mouse connector
6-pin wafer
KB_MS1
LVDS panel Connector
30-pin crimp
LVDS1
LCD panel backlight power connector
5-pin wafer
INV1
LAN LED connector
2-pin header
JP2, JP3
PCIe mini card slot
PCIe Mini card slot
CN1
Power button connector
2-pin wafer
PWR_BTN1
Reset button connector
2-pin wafer
RST_BTN1
RS-232 serial port connectors
10-pin header
COM2, COM3
RS-422/485 serial port connector
4-pin wafer
COM4
SATA 3Gb/s drive connectors
7-pin SATA connector
SATA1, SATA2
SATA power connectors
2-pin wafer
SATA_PWR1,
SATA_PWR2
SMBUS connector
4-pin wafer
CN2
USB 2.0 connectors
8-pin header
USB1, USB4
Table 3-1: Peripheral Interface Connectors
P a g e 16
WAFER-BT
3.1.3 Exte rn a l In te rfa c e P a n e l Co n n e c to rs
The table below lists the connectors on the external I/O panel.
Connector
Type
Label
LAN connector
RJ-45
LAN1
RS-232 serial port connector
DB-9 male
COM1
USB 2.0 connector
USB 2.0
USB2
USB 3.0 connector
USB 3.0
USB3
VGA Connector
15-pin female
VGA1
Table 3-2: Rear Panel Connectors
3.2 In te rn a l P e rip h e ra l Co n n e c to rs
The section describes all of the connectors on the WAFER-BT.
3.2.1 +12V DC-IN P o we r Co n n e c to r
CN La b e l:
CN5
CN Typ e :
4-pin Molex
CN Lo c a tio n :
See Figure 3-2
CN P in o u ts :
See Table 3-3
The connector supports the +12V power supply.
P a g e 17
WAFER-BT
Figure 3-2: +12V DC-IN Power Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
GND
3
+12V
4
+12V
Table 3-3: +12V DC-IN Power Connector Pinouts
3.2.2 Au d io Co n n e c to r
CN La b e l:
AUDIO1
CN Typ e :
10-pin header
CN Lo c a tio n :
See Figure 3-3
CN P in o u ts :
See Table 3-4
The audio connector is connected to external audio devices including speakers and
microphones for the input and output of audio signals to and from the system.
P a g e 18
WAFER-BT
Figure 3-3: Audio Connector Location
P IN NO.
DES CRIP TION
P IN NO.
DES CRIP TION
1
LINE_OUTR
2
LINEIN_R
3
Analog_GND
4
Analog_GND
5
LINE_OUTL
6
LINEIN_L
7
Analog_GND
8
Analog_GND
9
LMIC1-R
10
LMIC1-L
Table 3-4: Audio Connector Pinouts
3.2.3 Ba tte ry Co n n e c to r
CN La b e l:
BAT1
CN Typ e :
2-pin wafer
CN Lo c a tio n :
See Figure 3-4
CN P in o u ts :
See Table 3-5
The battery connector is connected to the system battery. The battery provides power to
the system clock to retain the time when power is turned off.
P a g e 19
WAFER-BT
Figure 3-4: Battery Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
VBATT
2
GND
Table 3-5: Battery Connector Pinouts
3.2.4 Bu zze r Co n n e c to r
CN La b e l:
SP1
CN Typ e :
2-pin wafer
CN Lo c a tio n :
See Figure 3-5
CN P in o u ts :
See Table 3-6
The buzzer connector is connected to the buzzer.
Figure 3-5: Buzzer Connector Location
P a g e 20
WAFER-BT
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
Buzzer +
2
Buzzer -
Table 3-6: Buzzer Connector Pinouts
3.2.5 CP U Fa n Co n n e c to r
CN La b e l:
CP U_FAN1
CN Typ e :
4-pin wafer
CN Lo c a tio n :
See Figure 3-6
CN P in o u ts :
See Table 3-7
The fan connector attaches to a cooling fan.
Figure 3-6: CPU Fan Connector Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
+12V
3
FANIO1
4
FANOUT1
Table 3-7: CPU Fan Connector Pinouts
3.2.6 DDR3L S O-DIMM S lo t
CN La b e l:
DIMM1
CN Typ e :
DDR3L SO-DIMM slot
CN Lo c a tio n :
See Figure 3-7
The DDR3L SO-DIMM slot is for DDR3L SO-DIMM memory module.
P a g e 21
WAFER-BT
Figure 3-7: DDR3L SO-DIMM Slot Location
3.2.7 Dig ita l I/O Co n n e c to r
CN La b e l:
DIO1
CN Typ e :
10-pin header
CN Lo c a tio n :
See Figure 3-8
CN P in o u ts :
See Table 3-8
The digital I/O connector provides programmable input and output for external devices.
The digital I/O provides 4-bit output and 4-bit input.
Figure 3-8: Digital I/O Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
+5V
P a g e 22
WAFER-BT
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
3
DGPO3
4
DGPO2
5
DGPO1
6
DGPO0
7
DGPI3
8
DGPI2
9
DGPI1
10
DGPI0
Table 3-8: Digital I/O Connector Pinouts
3.2.8 Dis p la y P o rt Co n n e c to r
CN La b e l:
DP 1
CN Typ e :
20-pin box header
CN Lo c a tio n :
See Figure 3-9
CN P in o u ts :
See Table 3-9
The disport port connector provides flexible display function that supports VGA, DVI,
LVDS, HDMI and DisplayPort via the disport port convert board.
Figure 3-9: Display Port Connector Location
Pin
Description
Pin
Description
1
+5V
2
DPD_OB_LANE1_N
3
DPD_OB_LANE1_P
4
GND
5
DPD_OB_LANE3_N
6
DPD_OB_LANE3_P
7
GND
8
AUX_CTRL_DET_D
P a g e 23
WAFER-BT
Pin
Description
Pin
Description
9
GND
10
DDI1_HPD#
11
DPD_AUX_CTRL_P2
12
DPD_AUX_CTRL_N2
13
GND
14
DPD_OB_LANE2_P
15
DPD_OB_LANE2_N
16
GND
17
DPD_OB_LANE0_P
18
DPD_OB_LANE0_N
19
+3.3V
20
NC
Table 3-9: Display Port Connector Pinouts
3.2.9 Fro n t P a n e l Co n n e c to r
CN La b e l:
CN4
CN Typ e :
6-pin wafer
CN Lo c a tio n :
See Figure 3-10
CN P in o u ts :
See Table 3-10
The front panel connector connects to the indicator LEDs on the system front panel.
Figure 3-10: Front Panel Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
2
GND
3
PWR_LED+
4
PWR_LED-
5
HDD_LED+
6
HDD_LED-
P a g e 24
WAFER-BT
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
Table 3-10: Front Panel Connector Pinouts
3.2.10 iRIS -1010 m o d u le s lot
CN La b e l:
IP MI1
CN Typ e :
IPMI 2.0 slot
CN Lo c a tio n :
See Figure 3-11
The iRIS-1010 module slot allows installation of the iRIS-1010 module.
Figure 3-11: iRIS-1010 Module Slot Location
WARNING:
The iRIS-1010 module slot is designed to install the IEI iRIS-1010 IPMI
2.0 module. DO NOT install other modules into the iRIS-1010 module
slot. Doing so may cause damage to the WAFER-BT.
3.2.11 Ke yb o a rd a n d Mo u s e Co n n e c to r
CN La b e l:
KB_MS 1
CN Typ e :
6-pin wafer
CN Lo c a tio n :
See Figure 3-12
P a g e 25
WAFER-BT
CN P in o u ts :
See Table 3-11
The keyboard/mouse connector connects to a PS/2 Y-cable that can be connected to a
PS/2 keyboard and mouse.
Figure 3-12: Keyboard and Mouse Location
Pin
Description
1
VCC
2
Mouse Data
3
Mouse Clock
4
Keyboard Data
5
Keyboard Clock
6
GND
Table 3-11: Keyboard and Mouse Connector Pinouts
3.2.12 LVDS Ba c klig h t In ve rte r Co n n e c to r
CN La b e l:
INV1
CN Typ e :
5-pin wafer
CN Lo c a tio n :
See Figure 3-13
CN P in o u ts :
See Table 3-12
The backlight inverter connector provides power to an LCD panel.
P a g e 26
WAFER-BT
Figure 3-13: Backlight Inverter Connector Location
Pin
Description
1
BRIGHTNESS2
2
GND
3
12V
4
GND
5
ENABKL2
Table 3-12: Backlight Inverter Connector Pinouts
3.2.13 LVDS LCD Co n n e c to r
CN La b e l:
LVDS 1
CN Typ e :
30-pin crimp
CN Lo c a tio n :
See Figure 3-14
CN P in o u ts :
See Table 3-13
The LVDS connector is for an LCD panel connected to the board.
P a g e 27
WAFER-BT
Figure 3-14: LVDS Connector Location
Pin
Description
Pin
Description
1
GND
16
LVDSB_DATA0#
2
GND
17
LVDSB_DATA1
3
LVDSA_DATA0
18
LVDSBDATA1#
4
LVDSA_DATA0#
19
LVDSB_DATA2
5
LVDSA_DATA1
20
LVDSB_DATA2#
6
LVDSA_DATA1#
21
LVDSB_CLK
7
LVDSA_DATA2
22
LVDSB_CLK#
8
LVDSA_DATA2#
23
LVDSB_DATA3
9
LVDSA_CLK
24
LVDSB_DATA3#
10
LVDSA_CLK#
25
GND
11
LVDSA_DATA3
26
GND
12
LVDSA_DATA3#
27
+3.3V
13
GND
28
+3.3V
14
GND
29
+3.3V
15
LVDSB_DATA0
30
+3.3V
Table 3-13: LVDS Connector Pinouts
3.2.14 LAN LED Co n n e c to r
CN La b e l:
P a g e 28
J P 2, J P 3
WAFER-BT
CN Typ e :
2-pin header
CN Lo c a tio n :
See Figure 3-15
CN P in o u ts :
See Table 3-14
The LAN LED connectors connect to the LAN link LEDs on the system.
Figure 3-15: LAN LED Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+3.3VLAN
2
LAN_LED_LINK#
Table 3-14: LAN LED Connector Pinouts
3.2.15 P CIe Min i Ca rd S lo t
CN La b e l:
CN1
CN Typ e :
PCIe Mini card slot
CN Lo c a tio n :
See Figure 3-16
The PCIe Mini card slot is for installing a PCIe Mini expansion card.
P a g e 29
WAFER-BT
Figure 3-16: PCIe Mini Card Slot Location
3.2.16 P owe r Bu tto n Co n n e c to r
CN La b e l:
P WR_BTN1
CN Typ e :
2-pin wafer
CN Lo c a tio n :
See Figure 3-17
CN P in o u ts :
See Table 3-15
The power button connector is connected to a power switch on the system chassis to
enable users to turn the system on and off.
Figure 3-17: Power Button Connector Location
Pin
Description
1
PWRBTN_SW#
P a g e 30
WAFER-BT
2
GND
Table 3-15: Power Button Connector Pinouts
3.2.17 Re s e t Bu tto n Co n n e c to r
CN La b e l:
RS T_BTN1
CN Typ e :
2-pin wafer
CN Lo c a tio n :
See Figure 3-18
CN P in o u ts :
See Table 3-16
The reset button connector is connected to a reset switch on the system chassis to enable
users to reboot the system when the system is turned on.
Figure 3-18: Reset Button Connector Location
Pin
Description
1
PM_SYSRST_R#
2
GND
Table 3-16: Reset Button Connector Pinouts
3.2.18 RS -232 S e ria l P o rt Co n n e c to rs
CN La b e l:
COM2, COM3
CN Typ e :
10-pin header
CN Lo c a tio n :
See Figure 3-19
CN P in o u ts :
See Table 3-17
P a g e 31
WAFER-BT
The serial connector provides RS-232 connection.
Figure 3-19: RS-232 Serial Port Connectors Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
NDCD
6
NDSR
2
NRXD
7
NRTS
3
NTXD
8
NCTS
4
NDTR
9
NRI
5
GND
10
GND
Table 3-17: RS-232 Serial Port Connector Pinouts
3.2.19 RS -422/485 S e ria l P ort Co n n e c to r
CN La b e l:
COM4
CN Typ e :
4-pin wafer
CN Lo c a tio n :
See Figure 3-20
CN P in o u ts :
See Table 3-18
This connector provides RS-422 or RS-485 communications.
P a g e 32
WAFER-BT
Figure 3-20: RS-422/485 Connector Location
Pin
Description
Pin
Description
1
RXD485#
2
RXD485+
3
TXD485+
4
TXD485#
Table 3-18: RS-422/485 Connector Pinouts
Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the DB-9
connector are listed below.
RS-422 Pinouts
RS-485 Pinouts
Table 3-19: DB-9 RS-422/485 Pinouts
3.2.20 S ATA 3Gb /s Drive Co n n e c to r
CN La b e l:
SATA1, SATA2
CN Typ e :
7-pin SATA connector
CN Lo c a tio n :
See Figure 3-21
P a g e 33
WAFER-BT
The SATA 3Gb/s drive connector is connected to a SATA 3Gb/s drive. The SATA 3Gb/s
drive transfers data at speeds as high as 3Gb/s.
Figure 3-21: SATA 3Gb/s Drive Connectors Locations
3.2.21 S ATA P o we r Co n n e c to r
CN La b e l:
SATA_PWR1
CN Typ e :
2-pin wafer
CN Lo c a tio n :
See Figure 3-22
CN P in o u ts :
See Table 3-20
The SATA power connector provides +5V power output to the SATA connector.
Figure 3-22: SATA Power Connector Location
PIN NO.
DESCRIPTION
1
+5V
P a g e 34
WAFER-BT
PIN NO.
DESCRIPTION
2
GND
Table 3-20: SATA Power Connector Pinouts
3.2.22 S MBUS Co n n e c to r
CN La b e l:
CN2
CN Typ e :
4-pin wafer
CN Lo c a tio n :
See Figure 3-23
CN P in o u ts :
See Table 3-21
The SMBUS (System Management Bus) connector provides low-speed system
management communications.
Figure 3-23: SMBUS Connectors Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
SMBDATA
3
SMBCLK
4
+5V
Table 3-21: SMBUS Connectors Pinouts
3.2.23 US B Co n n e c to rs
CN La b e l:
USB1, USB4
P a g e 35
WAFER-BT
CN Typ e :
8-pin header
CN Lo c a tio n :
See Figure 3-24
CN P in o u ts :
See Table 3-22
The USB connectors provide four USB 2.0 ports by dual-port USB cable.
Figure 3-24: USB Connectors Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
2
GND
3
-DATA_USB1/3
4
+DATA_USB2/4
5
+DATA_USB1/3
6
-DATA_USB2/4
7
GND
8
+5V
Table 3-22: USB Connectors Pinouts
3.3 Exte rn a l P e rip h e ra l In te rfa c e Co n n e c to r P a n e l
Figure 3-25 shows the WAFER-BT external peripheral interface connector (EPIC) panel.
The EPIC panel consists of the following:
P a g e 36

2 x LAN connectors

1 x USB 3.0 connector

1 x USB 2.0 connector

1 x RS-232 serial port connector

1 x VGA connector
WAFER-BT
Figure 3-25: External Peripheral Interface Connector
3.3.1 LAN Co n n e c to r
CN La b e l:
LAN1, LAN2
CN Typ e :
RJ-45
CN Lo c a tio n :
See Figure 3-25
CN P in o u ts :
See Figure 3-26 and Table 3-23
The LAN connector connects to a local network.
Figure 3-26: LAN Connector
Pin
Description
Pin
Description
1
MDIA3-
5
MDIA2+
2
MDIA3+
6
MDIA1+
3
MDIA1-
7
MDIA0-
4
MDIA2-
8
MDIA0+
Table 3-23: LAN Pinouts
P a g e 37
WAFER-BT
LED
Description
LED
Description
A
on: linked
B
off: 10 Mb/s
blinking: data is being sent/received
green: 100 Mb/s
orange: 1000 Mb/s
Table 3-24: Connector LEDs
3.3.2 US B Co n n e c to rs
CN La b e l:
US B2, US B3
CN Typ e :
USB 2.0 & USB 3.0 ports
CN Lo c a tio n :
See Figure 3-25
CN P in o u ts :
See Table 3-26
The WAFER-BT has one external USB 2.0 port and one external USB 3.0 port. The USB
connector can be connected to a USB device. The pinouts of USB 2.0 port & USB 3.0
connectors are shown below.
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
2
-DATA_USB3
3
-DATA_USB4
4
GND
Table 3-25: USB 2.0 Port Pinouts
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
2
USB2P0-
3
USB2P0+
4
GND
5
USB3P0_RXDN1
6
USB3P0_RXDP1
7
GND
8
USB3P0_TXDN1
9
USB3P0_TXDP1
Table 3-26: USB 3.0 Port Pinouts
3.3.3 RS -232 S e ria l P o rt Co n n e c to r
CN Label:
COM1
CN Type:
DB-9 Male
P a g e 38
WAFER-BT
CN Location:
See Figure 3-25
CN Pinouts:
See Figure 3-27 and Table 3-27
The serial port connects to a RS-232 serial communications device.
Figure 3-27: RS-232 Serial Port Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
NDCD1#
6
NDSR1#
2
NRXD1
7
NRTS1#
3
NTXD1
8
NCTS1#
4
NDTR1#
9
NRI1#
5
GND
Table 3-27: RS-232 Serial Port Connector Pinouts
3.3.4 VGA Co n n e c to r
CN La b e l:
VGA1
CN Typ e :
15-pin female (VGA)
CN Lo c a tio n :
See Figure 3-25
CN P in o u ts :
See Figure 3-28 and Table 3-28
The VGA port connects to a monitor that accepts a standard VGA input.
Figure 3-28: VGA Connector
P a g e 39
WAFER-BT
PIN
DESCRIPTION
PIN
DESCRIPTION
1
Red
2
Green
3
Blue
4
NC
5
GND
6
GND
7
GND
8
GND
9
VGAVCC
10
HOTPLUG
11
NC
12
DDCDAT
13
HSYNC
14
VSYNC
15
DDCCLK
Table 3-28: VGA Connector Pinouts
P a g e 40
WAFER-BT
Chapter
4
4 In s ta lla tio n
P a g e 41
WAFER-BT
4.1 An ti-s ta tic P re c a u tio n s
WARNING:
Failure to take ESD precautions during the installation of the
WAFER-BT may result in permanent damage to the WAFER-BT and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the WAFER-BT. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the WAFER-BT or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.

Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.

Self-grounding: Before handling the board, touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.

Use an anti-static pad: When configuring the WAFER-BT, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
WAFER-BT.

Only handle the edges of the PCB: When handling the PCB, hold the PCB
by the edges.
4.2 In s ta lla tio n Co n s id e ra tio n s
NOTE:
The following installation notices and installation considerations should
be read and understood before installation. All installation notices must
be strictly adhered to. Failing to adhere to these precautions may lead
to severe damage and injury to the person performing the installation.
P a g e 42
WAFER-BT
WARNING:
The installation instructions described in this manual should be carefully
followed in order to prevent damage to the WAFER-BT, WAFER-BT
components and injury to the user.
Before and during the installation please DO the following:

Read the user manual:
o
The user manual provides a complete description of the WAFER-BT
installation instructions and configuration options.

Wear an electrostatic discharge cuff (ESD):
o
Electronic components are easily damaged by ESD. Wearing an ESD cuff
removes ESD from the body and helps prevent ESD damage.

Place the WAFER-BT on an antistatic pad:
o
When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.

Turn all power to the WAFER-BT off:
o
When working with the WAFER-BT, make sure that it is disconnected
from all power supplies and that no electricity is being fed into the system.
Before and during the installation of the WAFER-BT DO NOT:

Remove any of the stickers on the PCB board. These stickers are required for
warranty validation.

Use the product before verifying all the cables and power connectors are
properly connected.

Allow screws to come in contact with the PCB circuit, connector pins, or its
components.
P a g e 43
WAFER-BT
4.3 S O-DIMM In s ta lla tio n
WARNING:
Using incorrectly specified SO-DIMM may cause permanently damage
the WAFER-BT. Please make sure the purchased SO-DIMM complies
with the memory specifications of the WAFER-BT. SO-DIMM
specifications compliant with the WAFER-BT are listed in the
specification table of Chapter 1.
To install an SO-DIMM, please follow the steps below and refer to Figure 4-1.
Figure 4-1: SO-DIMM Installation
S te p 1:
Locate the SO-DIMM socket. Place the board on an anti-static mat.
S te p 2:
Align the SO-DIMM with the socket. Align the notch on the memory with the
notch on the memory socket.
S te p 3:
Insert the SO-DIMM. Push the memory in at a 20º angle. (See Figure 4-1)
S te p 4:
Seat the SO-DIMM. Gently push downwards and the arms clip into place. (See
Figure 4-1)
P a g e 44
WAFER-BT
4.4 S ys te m Co n fig u ra tio n
The system configuration is controlled by buttons, jumpers and switches. The system
configuration should be performed before installation.
4.4.1 AT/ATX Mo d e S e le c t S witc h
CN La b e l:
J_ATX_AT1
CN Typ e :
switch
CN Lo c a tio n :
See Figure 4-2
CN S e ttin g s :
See Table 4-1
The AT/ATX mode select switch specifies the systems power mode as AT or ATX.
AT/ATX mode select switch settings are shown in Table 4-1.
Setting
Description
Short A-B
ATX Mode (Default)
Short B-C
AT Mode
Table 4-1: AT/ATX Mode Select Switch Settings
The location of the AT/ATX mode select switch is shown in Figure 4-2 below.
P a g e 45
WAFER-BT
Figure 4-2: AT/ATX Mode Select Switch Location
4.4.2 Cle a r CMOS Bu tto n
CN La b e l:
J _CMOS 1
CN Typ e :
button
CN Lo c a tio n :
See Figure 4-3
CN S e ttin g s :
See Table 4-2
If the WAFER-BT fails to boot due to improper BIOS settings, use the button to clear the
CMOS data and reset the system BIOS information.
The clear CMOS button settings are shown in Table 4-2.
Setting
Description
Open
Normal Operation
Push
Clear CMOS Setup
Default
Table 4-2: Clear CMOS Button Settings
The location of the clear CMOS button is shown in Figure 4-3
Figure 4-3: Clear CMOS Button Location
4.4.3 LVDS P a n e l Re s o lu tio n S e le c tio n
J u m p e r La b e l:
S W1
J u m p e r Typ e :
DIP switch
P a g e 46
WAFER-BT
J u m p e r S e ttin g s :
See Table 4-3
J u m p e r Lo c a tio n :
See Figure 4-4
Selects the resolution of the LCD panel connected to the LVDS connector.
* ON=0, OFF=1; Single=S, Dual=D
SW1 (4-3-2-1)
Description
0000
800x600 18-bit S
0001
1024x768 18-bit S
0010
1024x768 24-bit S
0011
1280x768 18-bit S
0100
1280x800 18-bit S
0101
1280x960 18-bit S
0110
1280x1024 24-bit D
0111
1366x768 18-bit S
1000
1366x768 24-bit S
1001
1440x960 24-bit D
1010
1400x1050 24-bit D
1011
1600x900 24-bit D
1100
1680x1050 24-bit D
1101
1600x1200 24-bit D
1110
1920x1080 24-bit D
1111
1920x1200 24-bit D
(default)
Table 4-3: LVDS Panel Resolution Selection
P a g e 47
WAFER-BT
Figure 4-4: LVDS Panel Resolution Selection Switch Location
4.4.4 LVDS Vo lta g e S e le c tio n
WARNING:
Permanent damage to the screen and WAFER-BT may occur if the
wrong voltage is selected with this jumper. Please refer to the user
guide that came with the monitor to select the correct voltage.
J u m p e r La b e l:
J_LCD_PWR1
J u m p e r Typ e :
switch
J u m p e r S e ttin g s :
See Table 4-4
J u m p e r Lo c a tio n :
See Figure 4-5
The LVDS voltage selection jumper allows setting the voltage provided to the monitor
connected to the LVDS connector.
Setting
Description
Short A-B
+3.3V (Default)
Short B-C
+5V
Table 4-4: LVDS Voltage Selection Jumper Settings
P a g e 48
WAFER-BT
Figure 4-5: LVDS Voltage Selection Jumper Location
4.4.5 Fla s h De s c rip to r S e c u rity Ove rrid e J u m p e r
J u m p e r La b e l:
J _FLAS H1
J u m p e r Typ e :
3-pin header
J u m p e r S e ttin g s :
See Table 4-5
J u m p e r Lo c a tio n :
See Figure 4-6
The Flash Descriptor Security Override jumper specifies whether to override the flash
descriptor.
Setting
Description
Short 1-2
No override (Default)
Short 2-3
Override
Table 4-5: Flash Descriptor Security Override Jumper Settings
P a g e 49
WAFER-BT
Figure 4-6: Flash Descriptor Security Override Jumper Location
4.5 In te rn a l P e rip h e ra l De vic e Co n n e c tio n s
This section outlines the installation of peripheral devices to the on-board connectors
4.5.1 Au d io Kit In s ta lla tio n
The Audio Kit that came with the WAFER-BT connects to the audio connector on the
WAFER-BT. The audio kit consists of three audio jacks. Mic-in connects to a microphone.
Line-in provides a stereo line-level input to connect to the output of an audio device.
Line-out, a stereo line-level output, connects to two amplified speakers. To install the
audio kit, please refer to the steps below:
S te p 1:
Locate the audio connector. The location of the 10-pin audio connector is
shown in Chapter 3.
S te p 2:
Align pin 1. Align pin 1 on the on-board connector with pin 1 on the audio kit
connector. Pin 1 on the audio kit connector is indicated with a white dot. See
Figure 4-7.
P a g e 50
WAFER-BT
Figure 4-7: Audio Kit Cable Connection
S te p 3:
Connect the audio devices. Connect speakers to the line-out audio jack.
Connect the output of an audio device to the line-in audio jack. Connect a
microphone to the mic-in audio jack.S te p 0:
4.5.2 S ATA Drive Co n n e c tio n
The WAFER-BT is shipped with a SATA drive cable. To connect the SATA drive to the
connector, please follow the steps below.
S te p 1:
Locate the SATA connector and the SATA power connector. The locations of
the connectors are shown in Chapter 3.
S te p 2:
Insert the cable connector. Insert the cable connector into the on-board SATA
drive connector and the SATA power connector. See Figure 4-8.
P a g e 51
WAFER-BT
Figure 4-8: SATA Drive Cable Connection
S te p 3:
Connect the cable to the SATA disk. Connect the connector on the other end
of the cable to the connector at the back of the SATA drive. See Figure 4-8.
S te p 4:
To remove the SATA cable from the SATA connector, press the clip on the
connector at the end of the cable. S te p 0:
4.5.3 S in g le RS -232 Ca ble
The single RS-232 cable consists of one serial port connector attached to a serial
communications cable that is then attached to a D-sub 9 male connector. To install the
single RS-232 cable, please follow the steps below.
S te p 1:
Locate the connector. The location of the RS-232 connector is shown in
Chapter 3.
P a g e 52
WAFER-BT
Insert the cable connector. Insert the connector into the serial port box header.
S te p 2:
See Figure 4-9. A key on the front of the cable connectors ensures the
connector can only be installed in one direction.
Figure 4-9: Single RS-232 Cable Installation
Secure the bracket. The single RS-232 connector has two retention screws
S te p 3:
that must be secured to a chassis or bracket.
Connect the serial device. Once the single RS-232 connector is connected to
S te p 4:
a chassis or bracket, a serial communications device can be connected to the
system.
4.6 Exte rn a l P e rip h e ra l In te rfa c e Co n n e c tio n
The following external peripheral devices can be connected to the external peripheral
interface connectors.

RJ-45 LAN cable

Serial port devices

USB devices

VGA monitor
P a g e 53
WAFER-BT
To install these devices, connect the corresponding cable connector from the actual
device to the corresponding WAFER-BT external peripheral interface connector making
sure the pins are properly aligned.
4.6.1 LAN Co n n e c tio n
There is one external RJ-45 LAN connector on the external peripheral interface panel. The
RJ-45 connector enables connection to an external network. To connect a LAN cable with
an RJ-45 connector, please follow the instructions below.
S te p 1:
Locate the RJ-45 connector. The location of the LAN connector is shown in
Chapter 3.
S te p 2:
Align the connector. Align the RJ-45 connector on the LAN cable with the
RJ-45 connectors on the WAFER-BT. See Figure 4-10.
Figure 4-10: LAN Connection
S te p 3:
Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN
cable RJ-45 connector into the on-board RJ-45 connector.
P a g e 54
WAFER-BT
4.6.2 S e ria l De vic e Co n n e c tio n
The WAFER-BT has two single female DB-9 connectors on the external peripheral
interface panel for a serial device. Follow the steps below to connect a serial device to the
WAFER-BT.
S te p 1:
Locate the DB-9 connector. The locations of the DB-9 connectors are shown
in Chapter 3.
S te p 2:
Insert the serial connector. Insert the DB-9 connector of a serial device into
the DB-9 connector on the external peripheral interface. See Figure 4-11.
Figure 4-11: Serial Device Connector
S te p 3:
Secure the connector. Secure the serial device connector to the external
interface by tightening the two retention screws on either side of the connecto
4.6.3 US B Co n n e c tio n
The external USB Series "A" receptacle connectors provide easier and quicker access to
external USB devices. Follow the steps below to connect USB devices to the WAFER-BT.
P a g e 55
WAFER-BT
S te p 1:
Locate the USB Series "A" receptacle connectors. The locations of the USB
Series "A" receptacle connectors are shown in Chapter 3.
S te p 2:
Insert a USB Series "A" plug. Insert the USB Series "A" plug of a device into
the USB Series "A" receptacle on the external peripheral interface. See
Figure 4-12.
Figure 4-12: USB Connector
4.6.4 VGA Mo n ito r Co n n e c tio n
The WAFER-BT has a single female DB-15 connector on the external peripheral interface
panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor
to the WAFER-BT, please follow the instructions below.
S te p 1:
Locate the female DB-15 connector. The location of the female DB-15
connector is shown in Chapter 3.
S te p 2:
Align the VGA connector. Align the male DB-15 connector on the VGA screen
cable with the female DB-15 connector on the external peripheral interface.
P a g e 56
WAFER-BT
S te p 3:
Insert the VGA connector. Once the connectors are properly aligned with the
insert the male connector from the VGA screen into the female connector on the
WAFER-BT. See Figure 4-13.
Figure 4-13: VGA Connector
S te p 4:
Secure the connector. Secure the DB-15 VGA connector from the VGA
monitor to the external interface by tightening the two retention screws on either
side of the connector.
P a g e 57
WAFER-BT
Chapter
5
5 BIOS
P a g e 58
WAFER-BT
5.1 In tro d u c tio n
The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to
certain system settings. This chapter outlines the options that can be changed.
NOTE:
Some of the BIOS options may vary throughout the life cycle of the
product and are subject to change without prior notice.
5.1.1 Sta rtin g S e tu p
The UEFI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DELETE or F2 key as soon as the system is turned on or
2. Press the DELETE or F2 key when the “Press Del to enter SETUP” message
appears on the screen. 0.
If the message disappears before the DELETE or F2 key is pressed, restart the computer
and try again.
5.1.2 Us in g S e tu p
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press ESC to quit. Navigation
keys are shown in.
Ke y
Fu n c tio n
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
+
Increase the numeric value or make changes
P a g e 59
WAFER-BT
Ke y
Fu n c tio n
-
Decrease the numeric value or make changes
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
F2 key
Load previous values.
F3 key
Load optimized defaults
F4 key
Save changes and Exit BIOS
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
Table 5-1: BIOS Navigation Keys
5.1.3 Ge ttin g He lp
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC or
the F1 key again.
5.1.4 Un a b le to Re b o o t a fte r Co n fig u ra tio n Ch a n g e s
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter 3.
5.1.5 BIOS Me n u Ba r
The menu bar on top of the BIOS screen has the following main items:
P a g e 60

Main – Changes the basic system configuration.

Advanced – Changes the advanced system settings.

Chipset – Changes the chipset settings.

Boot – Changes the system boot configuration.

Security – Sets User and Supervisor Passwords.

Save & Exit – Selects exit options and loads default settings
WAFER-BT
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
5.2 Ma in
The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
BIOS Information
BIOS Vendor
Core Version
Compliency
Project Version
Build Date and Time
American Megatrends
5.009
UEFI 2.3; PI 1.2
SAA8AR10.rom
06/20/2014 16:50:03
iWDD Vendor
iWDD Version
iEi
SAA8ER10.bin
IPMI Module
N/A
Memory Information
Total Memory
4096 MB(LPDDR3)
Set the Date. Use Tab to
switch between Data
elements.
---------------------
: Select Screen
↑ ↓: Select Item
Enter Select
+/-: Change Opt.
System Date
[Fri 06/20/2014]
F1: General Help
System Time
[19:43:27]
F2: Previous Values
F3: Optimized Defaults
Access Level
Administrator
F4: Save & Exit
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
TXE Information
Sec RC Version
TXE FW Version
00.05.00.00
01.00.02.1060
BIOS Menu 1: Main
The Main menu lists the following system details:

BIOS Information

iWDD Information

Memory Information

TXE Information
The System Overview field also has two user configurable fields:
P a g e 61
WAFER-BT

S ys te m Da te [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.

S ys te m Tim e [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
5.3 Ad va n c e d
Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
WARNING!
Setting the wrong values in the sections below may cause the system
to malfunction. Make sure that the settings made are compatible with
the hardware.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
>
>
>
>
>
>
>
>
ACPI Settings
Super IO Configuration
Hardware Monitor
RTC Wake Settings
Serial Port Console Redirection
CPU Configuration
IDE Configuration
USB Configuration
System ACPI Parameters.
---------------------: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 2: Advanced
P a g e 62
WAFER-BT
5.3.1 ACP I S e ttin g s
The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and
Power Interface (ACPI) options.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
ACPI Settings
ACPI Sleep State
[S3 (Suspend to RAM]
---------------------: Select Screen
↑ ↓: Select Item
Enter Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 3: ACPI Configuration

ACP I S le e p Sta te [S 3 o n ly (S u s p e n d to RAM)]
The fields in ACPI Sleep State option cannot be changed.

Suspend Disabled

S3
(Suspend
RAM)
to
Disable the suspend function.
DEFAULT
The caches are flushed and the CPU is powered
off. Power to the RAM is maintained. The
computer returns slower to a working state, but
more power is saved.
P a g e 63
WAFER-BT
5.3.2 S u pe r IO Co n fig u ra tio n
Use the Super IO Configuration menu (BIOS Menu 4) to set or change the
configurations for the serial ports.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Super IO Configuration
Super IO
> Serial
> Serial
> Serial
> Serial
Chip
Port
Port
Port
Port
Set Parameters of Serial
Port 1 (COMA)
F81866
1
2
3
4
Configuration
Configuration
Configuration
Configuration
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 4: Super IO Configuration
5.3.2.1 S e ria l P o rt n Co n fig u ra tio n
Use the Serial Port n Configuration menu (BIOS Menu 5) to configure the serial port n.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
F81216 Serial Port 1 Configuration
Serial Port
Device Settings
Enable or Disable Serial
Port (COM)
[Enabled]
IO=3F8h; IRQ=4
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
Change Settings
[Auto]
BIOS Menu 5: Serial Port n Configuration Menu
P a g e 64
WAFER-BT
5.3.2.1.1 S e ria l P o rt 1 Co n fig u ra tio n

S e ria l P o rt [En a b le d ]
Use the Serial Port option to enable or disable the serial port.


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Ch a n g e S e ttin g s [Au to ]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt
address are automatically detected.

IO=3F8h; IRQ=4
Serial Port I/O port address is 3F8h and the
interrupt address is IRQ4




IO=3F8h; IRQ=3,
Serial Port I/O port address is 3F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F8h; IRQ=3,
Serial Port I/O port address is 2F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=3E8h; IRQ=3,
Serial Port I/O port address is 3E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E8h; IRQ=3,
Serial Port I/O port address is 2E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
5.3.2.1.2 S e ria l P o rt 2 Co n fig u ra tio n

S e ria l P o rt [En a b le d ]
Use the Serial Port option to enable or disable the serial port.

Disabled
Disable the serial port
P a g e 65
WAFER-BT


Enabled
DEFAULT
Enable the serial port
Ch a n g e S e ttin g s [Au to ]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt
address are automatically detected.

IO=2F8h; IRQ=3
Serial Port I/O port address is 2F8h and the
interrupt address is IRQ3




IO=3F8h; IRQ=3,
Serial Port I/O port address is 3F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F8h; IRQ=3,
Serial Port I/O port address is 2F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=3E8h; IRQ=3,
Serial Port I/O port address is 3E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E8h; IRQ=3,
Serial Port I/O port address is 2E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
5.3.2.1.3 S e ria l P o rt 3 Co n fig u ra tio n

S e ria l P o rt [En a b le d ]
Use the Serial Port option to enable or disable the serial port.


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Ch a n g e S e ttin g s [Au to ]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
P a g e 66
WAFER-BT

Auto
DEFAULT
The serial port IO port address and interrupt
address are automatically detected.

Serial Port I/O port address is 3E8h and the
IO=3E8h; IRQ=7
interrupt address is IRQ7






IO=3F8h; IRQ=3,
Serial Port I/O port address is 3F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F8h; IRQ=3,
Serial Port I/O port address is 2F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=3E8h; IRQ=3,
Serial Port I/O port address is 3E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E8h; IRQ=3,
Serial Port I/O port address is 2E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F0h; IRQ=3,
Serial Port I/O port address is 2F0h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E0h; IRQ=3,
Serial Port I/O port address is 2E0h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
5.3.2.1.4 S e ria l P o rt 4 Co n fig u ra tio n

S e ria l P o rt [En a b le d ]
Use the Serial Port option to enable or disable the serial port.


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Ch a n g e S e ttin g s [Au to ]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt
address are automatically detected.
P a g e 67
WAFER-BT

IO=2E8h; IRQ=7
Serial Port I/O port address is 2E8h and the
interrupt address is IRQ7






IO=3F8h; IRQ=3,
Serial Port I/O port address is 3F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F8h; IRQ=3,
Serial Port I/O port address is 2F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=3E8h; IRQ=3,
Serial Port I/O port address is 3E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E8h; IRQ=3,
Serial Port I/O port address is 2E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F0h; IRQ=3,
Serial Port I/O port address is 2F0h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E0h; IRQ=3,
Serial Port I/O port address is 2E0h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
5.3.3 Ha rdwa re Mo n ito r
The Hardware Monitor menu (BIOS Menu 6) contains the fan configuration submenus
and displays operating temperature, fan speeds and system voltages.
P a g e 68
WAFER-BT
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
PC Health Status
Enable or Disable Smart
Fan
> Smart Fan Function
CPU temperature
System temperature
CPU Fan Speed
SYS Fan Speed
:+57 C
:+42 C
:N/A
:N/A
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 6: Hardware Monitor

P C He a lth Sta tu s
The following system parameters and values are shown. The system parameters that are
monitored are:

System Temperatures:
o
o

CPU Temperature
System temperature
Fan Speed:
o
o
CPU Fan Speed
SYS Fan Speed
5.3.3.1 S m a rt Fa n Mo d e Co nfig u ra tio n
Use the Smart Fan Mode Configuration submenu (BIOS Menu 7) to configure fan
temperature and speed settings.
P a g e 69
WAFER-BT
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Smart Fan Mode Configuration
CPU Smart Fan control
Temperature of Off
Temperature of Start
Start PWM
Slope(Duty Cycle)
CPU Smart Fan control
settings.
[Auto PWM Mode]
75
80
30
[4]
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 7: Smart Fan Mode Configuration

CP U S m a rt Fa n c o n tro l [Au to P WM Mo d e ]
Use the CPU Smart Fan control BIOS option to configure the CPU Smart Fan.

Full Mode
Fan is on all the time

Manual PWM Mode
The fan spins at the speed set in the manual
PWM setting

Auto PWM Mode
DEFAULT
The fan adjusts its speed using these
settings:
Temperature of Off
Temperature of Start
Start PWM
Slope (Duty Cycle)

Te m p e ra tu re o f Off [75]
WARNING:
Setting this value too high may cause the fan to speed up only when
P a g e 70
WAFER-BT
the CPU is at a very high temperature and therefore cause the system
to be damaged.
The Temperature of Off option can only be set if the CPU Smart Fan control option is
set to Auto Mode. If the CPU temperature is lower than Temperature of Off, the fan
speed change to be lowest. To set a value, select the Temperature of Off option and
enter a decimal number between 0 and 127. The temperature range is specified below.


Minimum Value: 0°C

Maximum Value: 127°C
Te m p e ra tu re o f Sta rt [80
WARNING:
Setting this value too high may cause the fan to rotate at full speed only
when the CPU is at a very high temperature and therefore cause the
system to be damaged.
The Temperature of Start option can only be set if the CPU Smart Fan control option is
set to Auto Mode. If the CPU temperature is between Temperature of Off and
Temperature of Start, the fan speed change to be Start PWM. To set a value, select the
Temperature of Start option and enter a decimal number between 0 and 127. The
temperature range is specified below.


Minimum Value: 0°C

Maximum Value: 127°C
Sta rt P WM [30]
The Start PWM option can only be set if the CPU Smart Fan control option is set to Auto
Mode. Use the Start PWM option to set the PWM start value. To set a value, select the
Start PWM option and enter a decimal number between 0 and 100. The temperature
range is specified below.
P a g e 71
WAFER-BT


Minimum Value: 0

Maximum Value: 100
S lo p e (Du ty Cyc le ) [4]
The Slope (Duty Cycle) option can only be set if the CPU Smart Fan control option is
set to Auto Mode. Use the Slope (Duty Cycle) option to select the linear rate at which the
PWM mode increases with respect to an increase in temperature. A list of available
options is shown below:

0

1

2

4

8

16
5.3.4 RTC Wa ke S e ttin g s
The RTC Wake Settings menu (BIOS Menu 8) configures RTC wake event.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Wake system with Fixed Time
[Disabled]
Enable or disable System
wake on alarm event. When
enabled, System will
wake on the
date::hr::min::sec
specified
----------------------
: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 8: RTC Wake Settings
P a g e 72
WAFER-BT

Wa ke s ys te m with Fixe d Tim e [Dis a b le d ]
Use the Wake system with Fixed Time option to enable or disable the system wake on
alarm event.

Disabled
DEFAULT
The real time clock (RTC) cannot generate a wake
event

Enabled
If selected, the Wake up every day option appears
allowing you to enable to disable the system to wake
every day at the specified time. Besides, the
following options appear with values that can be
selected:
Wake up date
Wake up hour
Wake up minute
Wake up second
After setting the alarm, the computer turns itself on
from a suspend state when the alarm goes off.
5.3.5 S e ria l P o rt Co n s o le Re d ire c tio n
The Serial Port Console Redirection menu (BIOS Menu 9) allows the console
redirection options to be configured. Console redirection allows users to maintain a
system remotely by re-directing keyboard input and text output through the serial port.
P a g e 73
WAFER-BT
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
COM1
Console Redirection
> Console Redirection Settings
[Disabled]
COM2
Console Redirection
> Console Redirection Settings
[Disabled]
COM3
Console Redirection
> Console Redirection Settings
[Disabled]
COM4
Console Redirection
> Console Redirection Settings
[Disabled]
IPMI COM (Disabled)
Console Redirection
Console Redirection
Enable or Disable
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Port Is Disabled
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 9: Serial Port Console Redirection

Co n s o le Re d ire c tio n [Dis a b le d ]
Use Console Redirection option to enable or disable the console redirection function.

Disabled

Enabled
DEFAULT
Disabled the console redirection function
Enabled the console redirection function
5.3.5.1 Co n s o le Re d ire c tio n S e ttin g s
The Console Redirection Settings menu (BIOS Menu 10) allows the console redirection
options to be configured. The option is active when Console Redirection option is enabled.
P a g e 74
WAFER-BT
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
COM1
Console Redirection Settings
Terminal Type
Bits per second
Data Bits
Parity
Stop Bits
[ANSI]
[115200]
[8]
[None]
[1]
Emulation: ANSI:
Extended ASCII char set.
VT100: ASCII char set.
VT100+: Extends VT100 to
support color, function
keys, etc. VT-UTF8: Uses
UTF8 encoding to map
Unicode chars onto 1 or
more bytes.
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 10: Console Redirection Settings

Te rm in a l Typ e [ANS I]
Use the Terminal Type option to specify the remote terminal type.


VT100
The target terminal type is VT100

VT100+
The target terminal type is VT100+

VT-UTF8
The target terminal type is VT-UTF8

ANSI
DEFAULT
The target terminal type is ANSI
Bits p e r s e c o n d [115200]
Use the Bits per second option to specify the serial port transmission speed. The speed
must match the other side. Long or noisy lines may require lower speeds.

9600
Sets the serial port transmission speed at 9600.

19200
Sets the serial port transmission speed at 19200.
P a g e 75
WAFER-BT


38400
Sets the serial port transmission speed at 38400.

57600
Sets the serial port transmission speed at 57600.

115200
DEFAULT
Sets the serial port transmission speed at 115200.
Da ta Bits [8]
Use the Data Bits option to specify the number of data bits.


7

8
Sets the data bits at 7.
DEFAULT
Sets the data bits at 8.
P a rity [No n e ]
Use the Parity option to specify the parity bit that can be sent with the data bits for
detecting the transmission errors.

None

Even
DEFAULT
No parity bit is sent with the data bits.
The parity bit is 0 if the number of ones in the data
bits is even.

The parity bit is 0 if the number of ones in the data
Odd
bits is odd.

The parity bit is always 1. This option does not
Mark
provide error detection.

The parity bit is always 0. This option does not
Space
provide error detection.

Sto p Bits [1]
Use the Stop Bits option to specify the number of stop bits used to indicate the end of a
serial data packet. Communication with slow devices may require more than 1 stop bit.

1

2
P a g e 76
DEFAULT
Sets the number of stop bits at 1.
Sets the number of stop bits at 2.
WAFER-BT
5.3.6 CP U Co n fig u ra tio n
Use the CPU Configuration menu (BIOS Menu 5) to view detailed CPU specifications
and configure the CPU.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
CPU Configuration
Intel(R) Celeron(R) CPU J1900 @ 1.99GHz
CPU Signature
30678
Microcode Patch
809
Max CPU Speed
1990 MHz
Min CPU Speed
1334 MHz
Processor Cores
4
Intel HT Technology
Not Supported
Intel VT-x Technology
Supported
L1 Data Cache
L1 Code Cache
L2 Cache
L3 Cache
CPU Speed
64-bit
24 KB x 2
32 KB x 2
1024 KB x 1
Not Present
2001 MHz
Supported
When enabled, a VMM can
utilize the additional
hardware capabilities
provided by Vanderpool
Technology.
----------------------
: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
Intel Virtualization Technology [Enabled]
F3
Optimized
EIST
[Enabled]
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 11: CPU Configuration

In te l® Virtu a liza tio n Te c h n o lo g y [Dis a b le d ]
Use the Intel® Virtualization Technology option to enable or disable virtualization on the
system. When combined with third party software, Intel Virtualization technology allows
several OSs to run on the same system at the same time.


Disabled

Enabled
DEFAULT
Disables Intel Virtualization Technology.
Enables Intel Virtualization Technology.
EIS T [En a b le d ]
Use the EIST option to enable or disable the Intel Speed Step Technology.
P a g e 77
WAFER-BT

Disabled

Enabled
Disables the Intel Speed Step Technology.
DEFAULT
Enables the Intel Speed Step Technology.
5.3.7 IDE Co n fig u ra tio n
Use the IDE Configuration menu (BIOS Menu 12) to change and/or set the configuration
of the SATA devices installed in the system.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
IDE Configuration
Select IDE/AHCI
SATA Mode
[AHCI Mode]
Serial-ATA Port 1
SATA Port 1 HotPlug
[Enabled]
[Disabled]
Serial-ATA Port 0
SATA Port 0 HotPlug
[Enabled]
[Disabled]
---------------------
SATA Port1
Not Present
SATA Port0
Not Present
: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 12: IDE Configuration

S ATA Mo d e [ACHI Mo d e ]
Use the SATA Mode option to configure SATA devices as normal IDE devices.


IDE Mode

ACHI Mode
Configures SATA devices as normal IDE device.
DEFAULT
Configures SATA devices as AHCI device.
S e ria l-ATA P o rt 1/0 [En a b le d ]
Use the Serial-ATA Port 1/0 option to enable or disable the SATA device.

Disabled

Enabled
P a g e 78
Disables the SATA device.
DEFAULT
Enables the SATA device.
WAFER-BT

S ATA P o rt 1/0 Ho tP lu g [Dis a b le d ]
Use the Serial-ATA Port 1/0 HotPlug option to enable or disable the SATA device hot
plug.

Disabled

Enabled
Disables the SATA device hot plug.
DEFAULT
Enables the SATA device hot plug
5.3.8 US B Co n fig u ra tio n
Use the USB Configuration menu (BIOS Menu 13) to read USB configuration
information and configure the USB settings.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
USB Configuration
USB Devices:
1 Keyboard
Legacy USB Support
[Enabled]
Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 13: USB Configuration

US B De vic e s
The USB Devices Enabled field lists the USB devices that are enabled on the system
P a g e 79
WAFER-BT

Le g a c y US B S u p p o rt [En a b le d ]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
keyboard can control the system even when there is no USB driver loaded onto the
system.

Enabled

Disabled
Legacy USB support disabled

Auto
Legacy USB support disabled if no USB devices are
DEFAULT
Legacy USB support enabled
connected
5.4 Ch ips e t
Use the Chipset menu (BIOS Menu 14) to access the Northbridge and Southbridge
configuration menus
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
P a g e 80
WAFER-BT
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset
Security
Boot
Save & Exit
> North Bridge
> South Bridge
North Bridge Parameters
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
+/-: Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 14: Chipset
5.4.1 No rth Brid g e Co n fig u ra tio n
Use the North Bridge Configuration menu (BIOS Menu 15) to configure the Intel IGD
settings.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
> Intel IGD Configuration
Memory Information
Total Memory
Memory Slot0
Configure Intel IGD
Settings.
4096 MB(LPDDR3)
4096 MB(LPDDR3)
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 15: Northbridge Chipset Configuration
P a g e 81
WAFER-BT

Me m o ry In fo rm a tio n
The Memory Information lists a brief summary of the on-board memory. The fields in
Memory Information cannot be changed.
5.4.1.1 In te l IGD Co n fig u ra tio n
Use the Intel IGD Configuration menu (BIOS Menu 16) to configure the video device
connected to the system.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
DVMT Pre-Allocated
DVMT Total Gfx Mem
[256M]
[MAX]
Primary IGFX Boot Display
[VBIOS Default]
Select DVMT 5.0
Pre-Allocated (Fixed)
Graphics Memory size
used by the Internal
Graphics Device.
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 16: Integrated Graphics

DVMT P re -Allo c a te d [256MB]
Use the DVMT Pre-Allocated option to set the amount of system memory allocated to the
integrated graphics processor when the system boots. The system memory allocated can
then only be used as graphics memory, and is no longer available to applications or the
operating system. Configuration options are listed below:
P a g e 82

64M

128M

256M

512M
Default
WAFER-BT

DVMT To ta l Gfx Me m [MAX]
Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size used
by the internal graphic device. The following options are available:


128M

256M

MAX
Default
P rim a ry IGFX Bo o t Dis p la y [VBIOS De fa u lt]
Use the Primary IGFX Boot Display option to select the display device used by the
system when it boots. For dual display support, select “VBIOS Deafult.” Configuration
options are listed below.

VBIOS Default DEFAULT

CRT

LVDS

DP Port
5.4.2 S o u th b rid g e Co n fig u ra tio n
Use the Southbridge Configuration menu (BIOS Menu 17) to configure the Southbridge
chipset.
P a g e 83
WAFER-BT
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
Auto Power Button Status
[Disabled(ATX)]
Restore AC Power Loss
[Last State]
EUP Disable/Enable.
> PCI Express Configuration
--------------------: Select Screen
[Enabled]
↑ ↓: Select Item
Enter Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
Audio Configuration
Audio Controller
BIOS Menu 17: Southbridge Chipset Configuration

Re s to re o n AC P o we r Lo s s [La s t Sta te ]
Use the Restore on AC Power Loss BIOS option to specify what state the system
returns to if there is a sudden loss of power to the system.

Power Off
The system remains turned off

Power On
The system turns on

Last State
DEFAULT
The system returns to its previous state. If it was on, it
turns itself on. If it was off, it remains off.

Au d io Co n tro lle r [En a b le d ]
Use the Audio Controller option to enable or disable the High Definition Audio controller.

Disabled

Enabled
The onboard High Definition Audio controller is disabled
DEFAULT
The onboard High Definition Audio controller is detected
automatically and enabled
P a g e 84
WAFER-BT
5.4.2.1 P CI Exp re s s Co n fig u ra tio n
Use the PCI Express Configuration menu (BIOS Menu 17) to configure the PCI
Express.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
PCI Express Configuration
PCI Express Port 0
Speed
[Enabled]
[Auto]
PCI Express Port 1
Speed
[Enabled]
[Auto]
PCI Express Port 2
Speed
[Enabled]
[Auto]
PCI Express Port 3
Speed
[Enabled]
[Auto]
Enable or Disable the PCI
Express Port 0 in the
Chipset.
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 18: Console Redirection Settings

P CI Exp re s s P o rt [En a b le d ]
Use the PCI Express Port option to enable or disable the PCI Express port.


Disabled

Enabled
Disables the PCI Express port.
DEFAULT
Enables the PCI Express port.
Sp e e d [Au to ]
Use the Speed option to configure PCIe port speed.

Auto
Configure PCIe port speed to auto

Gen 2
Configure PCIe port speed to Gen2

Gen 1
Configure PCIe port speed to Gen1
P a g e 85
WAFER-BT
5.5 S e c u rity
Use the Security menu (BIOS Menu 19) to set system and user passwords.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Password Description
If ONLY the Administrator’s password is set,
then this only limits access to Setup and is
only asked for when entering Setup
If ONLY the User’s password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will
have Administrator rights.
The password length must be:
Minimum length
3
Maximum length
20
Administrator Password
User Password
Set Setup Administrator
Password
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 19: Security

Ad m in is tra to r P a s s wo rd
Use the Administrator Password to set or change a administrator password.

Us e r P a s s wo rd
Use the User Password to set or change a user password.
P a g e 86
WAFER-BT
5.6 Bo o t
Use the Boot menu (BIOS Menu 17) to configure system boot options.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Boot Configuration
Bootup NumLock State
Quiet Boot
Option ROM Messages
UEFI Boot
Launch PXE OpROM
[On]
[Enabled]
[Force BIOS]
[Disabled]
[Disabled]
Select the keyboard
NumLock state
--------------------: Select Screen
↑ ↓: Select Item
Boot Option Priorities
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 20: Boot

Bo o tu p Nu m Lo c k Sta te [On ]
Use the Bootup NumLock State BIOS option to specify if the number lock setting must
be modified during boot up.

On
DEFAULT
Allows the Number Lock on the keyboard to be
enabled automatically when the computer system
boots up. This allows the immediate use of the
10-key numeric keypad located on the right side of
the keyboard. To confirm this, the Number Lock LED
light on the keyboard is lit.

Off
Does not enable the keyboard Number Lock
automatically. To use the 10-keys on the keyboard,
press the Number Lock key located on the upper
left-hand corner of the 10-key pad. The Number
Lock LED on the keyboard lights up when the
Number Lock is engaged.
P a g e 87
WAFER-BT

Qu ie t Bo o t [En a b le d ]
Use the Quiet Boot BIOS option to select the screen display when the system boots.


Disabled

Enabled
Normal POST messages displayed
DEFAULT
OEM Logo displayed instead of POST messages
Op tio n ROM Me s s a g e s [Fo rc e BIOS ]
Use the Option ROM Messages option to set the Option ROM display mode.

Force
DEFAULT
Sets display mode to force BIOS.
BIOS

Sets display mode to current.
Keep
Current

UEFI Bo o t [Dis a b le d ]
Use the UEFI Boot option to enable or disable to boot from the UEFI devices.

If the first boot HDD is GPT then enable UEFI boot
Auto
options, otherwise disable,


Enabled

Disabled
Boot from UEFI devices is enabled.
DEFAULT
Boot from UEFI devices is disabled.
La u n c h P XE Op ROM [Dis a b le d ]
Use the Launch PXE OpROM option to enable or disable boot option for legacy network
devices.

Disabled

Enabled
P a g e 88
DEFAULT
Ignore all PXE Option ROMs
Load PXE Option ROMs.
WAFER-BT

Bo o t Op tio n P rio rity
Use the Boot Option Priority function to set the system boot sequence from the available
devices. The drive sequence also depends on the boot sequence in the individual device
section.
5.7 Exit
Use the Exit menu (BIOS Menu 21) to load default BIOS values, optimal failsafe values
and to save configuration changes.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Save Changes and Reset
Discard Changes and Reset
Reset the system after
saving the changes.
Restore Defaults
Save as User Defaults
Restore User Defaults
--------------------: Select Screen
↑ ↓: Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 21:Exit

S a ve Ch a n g e s a n d Re s e t
Use the Save Changes and Reset option to save the changes made to the BIOS options
and to exit the BIOS configuration setup program.

Dis c a rd Ch a n g e s a n d Re s e t
Use the Discard Changes and Reset option to exit the system without saving the
changes made to the BIOS configuration setup program.
P a g e 89
WAFER-BT

Re s to re De fa u lts
Use the Restore Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F3 key can be used for this operation.

S a ve a s Us e r De fa u lts
Use the Save as User Defaults option to save the changes done so far as user defaults.

Re s to re Us e r De fa u lts
Use the Restore User Defaults option to restore the user defaults to all the setup options.
P a g e 90
WAFER-BT
Ap p e n d ix
A
A BIOS Me n u Op tio n s
P a g e 91
WAFER-BT

System Date [xx/xx/xx] ........................................................................................................62

System Time [xx:xx:xx] .......................................................................................................62

ACPI Sleep State [S3 only (Suspend to RAM)] .................................................................63

Serial Port [Enabled] ............................................................................................................65

Change Settings [Auto] .......................................................................................................65

Serial Port [Enabled] ............................................................................................................65

Change Settings [Auto] .......................................................................................................66

Serial Port [Enabled] ............................................................................................................66

Change Settings [Auto] .......................................................................................................66

Serial Port [Enabled] ............................................................................................................67

Change Settings [Auto] .......................................................................................................67

PC Health Status ..................................................................................................................69

CPU Smart Fan control [Auto PWM Mode]........................................................................70

Temperature of Off [75] .......................................................................................................70

Temperature of Start [80 .....................................................................................................71

Start PWM [30] ......................................................................................................................71

Slope (Duty Cycle) [4] ..........................................................................................................72

Wake system with Fixed Time [Disabled]..........................................................................73

Console Redirection [Disabled]..........................................................................................74

Terminal Type [ANSI] ...........................................................................................................75

Bits per second [115200] .....................................................................................................75

Data Bits [8] ..........................................................................................................................76

Parity [None] .........................................................................................................................76

Stop Bits [1] ..........................................................................................................................76

Intel® Virtualization Technology [Disabled]......................................................................77

EIST [Enabled] ......................................................................................................................77

SATA Mode [ACHI Mode] ....................................................................................................78

Serial-ATA Port 1/0 [Enabled] .............................................................................................78

SATA Port 1/0 HotPlug [Disabled] ......................................................................................79

USB Devices .........................................................................................................................79

Legacy USB Support [Enabled] ..........................................................................................80

Memory Information ............................................................................................................82

DVMT Pre-Allocated [256MB]..............................................................................................82

DVMT Total Gfx Mem [MAX]................................................................................................83
P a g e 92
WAFER-BT

Primary IGFX Boot Display [VBIOS Default] .....................................................................83

Restore on AC Power Loss [Last State] ............................................................................84

Audio Controller [Enabled] .................................................................................................84

PCI Express Port [Enabled] ................................................................................................85

Speed [Auto] .........................................................................................................................85

Administrator Password .....................................................................................................86

User Password .....................................................................................................................86

Bootup NumLock State [On] ...............................................................................................87

Quiet Boot [Enabled] ...........................................................................................................88

Option ROM Messages [Force BIOS] .................................................................................88

UEFI Boot [Disabled] ...........................................................................................................88

Launch PXE OpROM [Disabled] .........................................................................................88

Boot Option Priority .............................................................................................................89

Save Changes and Reset ....................................................................................................89

Discard Changes and Reset ...............................................................................................89

Restore Defaults ..................................................................................................................90

Save as User Defaults .........................................................................................................90

Restore User Defaults .........................................................................................................90
P a g e 93
WAFER-BT
Ap p e n d ix
B
B Te rm in o lo g y
P a g e 94
WAFER-BT
AC ’97
Audio Codec 97 (AC’97) refers to a codec standard developed by
Intel® in 1997.
ACPI
Advanced Configuration and Power Interface (ACPI) is an OS-directed
configuration, power management, and thermal management interface.
AHCI
Advanced Host Controller Interface (AHCI) is a SATA Host controller
register-level interface.
ATA
The Advanced Technology Attachment (ATA) interface connects
storage devices including hard disks and CD-ROM drives to a
computer.
APM
The Advanced Power Management (APM) application program
interface (API) enables the inclusion of power management in the
BIOS.
ARMD
An ATAPI Removable Media Device (ARMD) is any ATAPI device that
supports removable media, besides CD and DVD drives.
ASKIR
Amplitude Shift Keyed Infrared (ASKIR) is a form of modulation that
represents a digital signal by varying the amplitude (“volume”) of the
signal. A low amplitude signal represents a binary 0, while a high
amplitude signal represents a binary 1.
BIOS
The Basic Input/Output System (BIOS) is firmware that is first run when
the computer is turned on and can be configured by the end user
CODEC
The Compressor-Decompressor (CODEC) encodes and decodes
digital audio data on the system.
CMOS
Complimentary metal-oxide-conductor is a type of integrated circuit
used in chips like static RAM and microprocessors.
COM
COM is used to refer to serial ports. Serial ports offer serial
communication to expansion devices. The serial port on a personal
P a g e 95
WAFER-BT
computer is usually a male DE-9 connector.
DAC
The Digital-to-Analog Converter (DAC) converts digital signals to
analog signals.
DDR
Double Data Rate refers to a data bus transferring data on both the
rising and falling edges of the clock signal.
DMA
Direct Memory Access (DMA) enables some peripheral devices to
bypass the system processor and communicate directly with the
system memory.
DIMM
Dual Inline Memory Modules are a type of RAM that offer a 64-bit data
bus and have separate electrical contacts on each side of the module.
EHCI
The Enhanced Host Controller Interface (EHCI) specification is a
register-level interface description for USB 2.0 Host Controllers.
GbE
Gigabit Ethernet (GbE) is an Ethernet version that transfers data at 1.0
Gbps and complies with the IEEE 802.3-2005 standard.
GPIO
General purpose input
IrDA
Infrared Data Association (IrDA) specify infrared data transmission
protocols used to enable electronic devices to wirelessly communicate
with each other.
L1 Cache
The Level 1 Cache (L1 Cache) is a small memory cache built into the
system processor.
L2 Cache
The Level 2 Cache (L2 Cache) is an external processor memory cache.
LVDS
Low-voltage differential signaling (LVDS) is a dual-wire, high-speed
differential electrical signaling system commonly used to connect LCD
displays to a computer.
MAC
The Media Access Control (MAC) protocol enables several terminals or
network nodes to communicate in a LAN, or other multipoint networks.
P a g e 96
WAFER-BT
PCIe
PCI Express (PCIe) is a communications bus that uses dual data lines
for full-duplex (two-way) serial (point-to-point) communications between
the SBC components and/or expansion cards and the SBC chipsets.
Each line has a 2.5 Gbps data transmission rate and a 250 MBps
sustained data transfer rate.
POST
The Power-on Self Test (POST) is the pre-boot actions the system
performs when the system is turned-on.
QVGA
Quarter Video Graphics Array (QVGA) refers to a display with a
resolution of 320 x 240 pixels.
RAM
Random Access Memory (RAM) is a form of storage used in computer.
RAM is volatile memory, so it loses its data when power is lost. RAM
has very fast data transfer rates compared to other storage like hard
drives.
SATA
Serial ATA (SATA) is a serial communications bus designed for data
transfers between storage devices and the computer chipsets. The
SATA bus has transfer speeds up to 1.5 Gbps and the SATA 3Gb/s bus
has data transfer speeds of up to 3.0 Gbps.
S.M.A.R.T
Self Monitoring Analysis and Reporting Technology (S.M.A.R.T) refers
to automatic status checking technology implemented on hard disk
drives.
UART
Universal Asynchronous Receiver-transmitter (UART) is responsible for
asynchronous communications on the system and manages the
system’s serial communication (COM) ports.
UHCI
The Universal Host Controller Interface (UHCI) specification is a
register-level interface description for USB 1.1 Host Controllers.
USB
The Universal Serial Bus (USB) is an external bus standard for
interfacing devices. USB 1.1 supports 12Mbps data transfer rates, while
P a g e 97
WAFER-BT
USB 2.0 supports 480Mbps data transfer rates.
VGA
The Video Graphics Array (VGA) is a graphics display system
developed by IBM.
P a g e 98
WAFER-BT
Ap p e n d ix
C
C Ha za rd o u s Ma te ria ls
Dis c lo s u re
P a g e 99
WAFER-BT
C.1 Ha za rd o u s Ma te ria l Dis c lo s ure Ta b le fo r IP B P ro d u c ts
Ce rtifie d a s Ro HS Co m p lia n t Un d e r 2002/95/EC With o u t
Me rc u ry
The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain materials in the product, and is applicable to China
RoHS only.
A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.
Please refer to the table on the next page.
P a g e 100
WAFER-BT
Part Name
Toxic or Hazardous Substances and Elements
Lead
Mercury
Cadmium
Hexavalent
Polybrominated
Polybrominated
(Pb)
(Hg)
(Cd)
Chromium
Biphenyls
Diphenyl Ethers
(CR(VI))
(PBB)
(PBDE)
Housing
O
O
O
O
O
O
Display
O
O
O
O
O
O
Printed Circuit
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Fan Assembly
O
O
O
O
O
O
Power Supply
O
O
O
O
O
O
O
O
O
O
O
O
Board
Metal
Fasteners
Cable
Assembly
Assemblies
Battery
O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below
the limit requirement in SJ/T11363-2006
X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part
is above the limit requirement in SJ/T11363-2006
P a g e 101
WAFER-BT
此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。
本产品上会附有”环境友好使用期限”的标签,此期限是估算这些物质”不会有泄漏或突变”的
年限。本 产品可能包含有较短的环境友好使用期限的可替换元件,像是电池或灯管,这些元
件将会单独标示出来。
部件名称
有毒有害物质或元素
铅
汞
镉
六价铬
多溴联苯
多溴二苯醚
(Pb)
(Hg)
(Cd)
(CR(VI))
(PBB)
(PBDE)
壳体
O
O
O
O
O
O
显示
O
O
O
O
O
O
印刷电路板
O
O
O
O
O
O
金属螺帽
O
O
O
O
O
O
电缆组装
O
O
O
O
O
O
风扇组装
O
O
O
O
O
O
电力供应组装
O
O
O
O
O
O
电池
O
O
O
O
O
O
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
P a g e 102
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement