HHM598T
OMEGA
HHM598T
Digital Trms Clamp-On Meter
omega.com
TM
OMEGAnetSM On-Line Service
http://www.omega.com
USA: ISO 9001 Certified
One Omega Drive, Box 4047
Stamford, CT 06907-0047
Tel: (203) 359-1660
FAX: (203)359-7700
e-mail: [email protected]
Internet e-mail
[email protected]
Servicing North America:
Canada:
976 Bergar
Laval (Quebec) H7L5A1
Tel: (514) 856-6928
FAX: (514) 856-6886
e-mail: [email protected]
For immediate technical or application assistance:
USA and Canada:
Sales Service: 1-800-826-6342 / 1-800-TC-OMEGASM
Customer Service: 1-800-622-2378 / 1-800-622-BESTSM
Engineering Service: 1-800-872-9436 / 1-800-USA-WHENSM
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
Mexico and Latin America:
Tel: (95) 800-TC-OMEGASM
FAX: (95) 203-359-7807
En Español: (203) 359-7803
e-mail: [email protected]
Servicing Europe:
Benelux:
Postbus 8034, 1180 LA Amstelveen,
The Netherlands
Tel: (31) 20 6418405 FAX: (31) 20 6434643
Toll Free in Benelux: 06 0993344
e-mail: [email protected]
Germany/Austria:
Daimlerstrasse 26, D-75392
Deckenpfronn, Germany
Tel: 49 (07056) 3017 FAX: 49 (07056) 8540
Toll Free in Germany: 0800 82 66342
e-mail: [email protected]
Czech Republic:
ul. Rude armady 1868, 733 01 KarvinaHranice, Czech Repubic
Tel: 420 (69) 6311627 FAX: 420 (69) 6311114
e-mail: [email protected]
United Kingdom: ISO 9002 Certified
One Omega Drive
Riverbend Technology Centre Northbank, Irlam,
Manchester, M44 5EX, England
Tel: 44 (161) 777-6611 FAX: 44 (161) 777-6622
France:
9, rue Denis Papin, 78190 Trappes
Tel: (33) 130-621-400 FAX: (33)130-699-120
Toll Free in France: 0800-4-06342
e-mail: [email protected]
Toll Free in England: 0800-488-488
e-mail: [email protected]
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification
of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct but OMEGA Engineering, Inc. accepts no liability for any errors it contains,
and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient connected application.
SAFETY INFORMATION
The following safety information must be observed to insure maximum
personal safety during the operation at this meter:
1. Do not use the meter if the meter or test leads look damaged, or if you
suspect that the meter is not operating properly.
2. Use caution when working above 60V dc or 30V ac rms. Such voltages pose
a shock hazard.
3. When Using the probes, keep your fingers behind the finger guards on the
probes.
4. Measuring voltage which exceeds the limits of the clampmeter may damage
the meter and expose the operator to a shock hazard. Always recognize the
meter voltage limits as stated on the front of the meter.
5. If the equipment is used in a manner not specified by the manufacturer, the
protection provided the equipment may be impaired.
1
SPECIFICATIONS
Display: 3½ digit liquid crystal display (LCD) with a maximum reading of 1999.
Polarity: Automatic, positive implied, negative polarity indication.
Overrange: (OL) or (-OL) is displayed.
Zero: Automatic.
Low battery indication: the " " is displayed when the battery voltage drops
below the operating level.
Measurement rate: 2.5 times per second, nominal.
Operating Environment: 0°C to 40°C at < 70% relative humidity.
Storage Temperature: -20°C to 60°C, 0 to 80% R.H. with battery removed
from meter.
Accuracy: Stated accuracy at 23°C ± 5°C, <75% relative humidity.
Safety: According to EN61010-1 protection class II overvoltage category
(CAT III 600V) pollution degree 2.
Clamp jaw: According to EN61010-2-032 CAT IV 600V.
Power: single standard 9-volt battery.
Battery life: 200 hours typical.
Dimensions: 250mm (H) x 100mm (W) x 46mm (D).
Weight: Approx. 380g including battery.
Accessories: One pair test leads, 9V battery.
2
DC VOLTS
Ranges: 600V
Accuracy: ±(0.5%rdg + 1dgt)
Input impedance: 10MW
Overload protection: 600VDC or AC rms
AC VOLTS (True RMS) (50Hz - 500Hz)
Ranges: 200V,600V
Accuracy: ±(1.2%rdg + 10dgts)
Input impedance: 10MW
Overload protection: 600VDC or AC rms
RESISTANCE
Ranges: 2KW ,200KW
Accuracy: ±(1.2%rdg + 1dgt)
Open circuit volts: 0.3Vdc
Overload protection: 600VDC or AC rms
FREQUENCY (Autoranging)
Ranges: 2KHz,20KHz
Accuracy: ±(0.1%rdg + 3dgts)
Sensitivity: 80Vrms min
Overload protection: 600VDC or AC rms
3
CONTINUITY
Audible indication: less than 30W on 2KW range
Overload protection: 600VDC or AC rms
DIODE TEST
Test current: 1.0mA±0.6mA
Accuracy: ±(6.0%rdg + 3dgts)
Open circuit volts: 3.0Vdc typical
Audible indication: <30mV
Overload protection: 600VDC or AC rms
AC CURRENT (True RMS) (Put conductor at the center of the jaws)
Ranges: 20A,200A,700A
Accuracy: 50-60Hz ±(1.5%rdg + 10dgts)
40-500Hz ±(3.5%rdg + 10dgts)
*700A to 1000A(50Hz-60Hz): ±(2.0%rdg + 10dgts)
Overload protection: 1000Aac max. for 1 minute
4
OPERATION
Before taking any measurements, read the Safety Information Section.
Always examine the instrument for damage, contamination (excessive dirt,
grease, etc.) and defects. Examine the test leads for cracked or frayed
insulation. If any abnormal conditions exist do not attempt to make any
measurements.
H Button:
Press " H " button to toggle in and out of DATA Hold mode, In the DATA Hold
mode, the " H " annunciator is displayed. (The DATA Hold mode may be exited
when changing function.)
MAX HOLD Button:
Press "MAX" button to toggle in and out of MAX Hold mode (holding the highest
absolute reading). In the MAX Hold mode, the " MAX " annunciator is
displayed.
Current and Hz ranges without MAX HOLD function.
PEAK HOLD Button: (only current ranges 40-60Hz)
Press "PEAK" button to toggle in and out of PEAK Hold mode. In the PEAK
Hold mode, the " P " annunciator is displayed. {Accuracy: ±[10%(readind residual offset)+10dgts], effect reading: 80~2000}
5
Voltage Measurements
1. Connect the red test lead to the "V" jack and the black test lead to the "COM"
jack.
2. Set the Function/Range switch to the desired Voltage type (AC or DC) and
range. If magnitude of voltage is not known, set switch to the highest range
and reduce until a satisfactory reading is obtained.
3. Connect the test leads to the device or circuit being measured.
4. For dc, a (-) sign is displayed for negative polarity, positive polarity is implied.
Current Measurements
1. Set the Function/Range switch to the highest 700A ac range.
2. Press the trigger to open transformer jaws and clamp onto one conductor
only. Read the current directly on the display. It is recommended that the
conductor be placed at the center of the closed jaws for maximum accuracy.
3. When the reading is lower than 200 counts, set the range switch to the next
lower range position. For maximum accuracy, select the lower range
possible without overranging the meter.
Resistance Measurements
1. Set the Function/Range switch to the desired resistance range.
2. Remove power from the equipment under test.
3. Connect the red test lead to the " + " jack and the black test lead to the "COM"
jack.
4. Touch the probes to the test points. In ohms, the value indicated in the
display is the measured value of resistance.
6
WARNING
The accuracy of the functions might be slightly affected, when exposed to
a radiated electromagnetic field environment, eg, radio, telephone or
similar.
Frequency Measurements
1. Set the Function/Range switch to the Hz position.
2. Connect the red test lead to the " + " jack and the black test lead to the "COM"
jack.
3. Connect the test leads to the point of measurement and read the frequency
from the display.
Continuity Measurements
1. Set the Function/Range switch to the " 2KW " position.
2. Touch the probes to the test points. the beeper sounds continuously, if the
resistance is less than 30W .
7
Diode Tests
1. Connect the red test lead to the " + " jack and the black test lead to the "COM"
jack.
2. Set the Function/Range switch to the " " position.
3. Turn off power to the circuit under test.
4. Touch probes to the diode. A forward-voltage drop is about 0.6V (typical for
a silicon diode).
5. Reverse probes. If the diode is good, "OL" is displayed. If the diode is
shorted, ".000" or another number is displayed.
6. If the diode is open, "OL" is displayed in both directions.
7. If the junction is measured in a circuit and a low reading is obtained with both
lead connections, the junction may be shunted by a resistance of less than
1kW . In this case the diode must be disconnected from the circuit for
accurate testing.
8
MAINTENANCE
WARNING
Remove test leads before changing battery
or performing any servicing.
Battery Replacement
Power is supplied by a 9 volt "transistor" battery. (NEDA 1604, IEC 6F22). The
" " appears on the LCD display when replacement is needed. To replace the
battery, remove the two screws from the back of the meter and lift off the
battery cover. Remove the battery from battery contacts.
Cleaning
Periodically wipe the case with a damp cloth and detergent, do not use
abrasives or solvents.
9
WARRANTY / DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months
from date of purchase. OMEGA Warranty adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA's customers receive maximum coverage on each product.If
the unit should malfunction, it must be returned to the factory for evaluation. OMEGA's Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to
be defective it will be repaired or replaced at no charge. OMEGA's WARRANTY does not apply to defects resulting from any action
of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair,
or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence
of being damaged as a result of excessive corrosion; or current, heat moisture or vibration; improper specification; misapplication;
misuse or other operating conditions outside of OMEGA's control. Components which wear are not warranted, including but not
limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility
for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance
with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by it
will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND
WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE AND ALL IMPLIED WARRANTIES INCLUDING ANY
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive and the total liability of OMEGA with
respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall
not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a "Basic Component" under 10
CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any
Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way,
OMEGA assumes no responsibility as set forth in our basic WARRANTY / DISCLAIMER language, and additionally, purchaser will
indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in
such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA'S
CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then
be marked on the outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please have the following
information available BEFORE contacting OMEGA:
1. P.O. number under which the product was PURCHASED.
2. Model and serial number of the product under warranty, and
3. Repair instructions and/or specific problems relative to the
product.
FOR NON-WARRANTY REPAIRS, consult OMEGA for
current repair charges. Have the following information
available BEFORE contacting OMEGA:
1. P.O. number to cover the COST of the repair.
2. Model and serial number of product , and
3. Repair instructions and/or specific problems relative to the
product.
OMEGA's policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest
in technology and engineering. OMEGA is a registered trademark of OMEGA ENGINEERING, INC. © Copyright 1999 OMEGA ENGINEERING,
INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or
machine-readable from, in whole or in part, without prior written consent of OMEGA ENGINEERING, INC.
Where Do I Find Everything I Need for
Process Measurement and Control?
OMEGA...Of Course!
TEMPERATURE
DATA ACQUISITION
þ Thermocouple, RTD & Thermistor
Probes, Connectors, Panels & Assemblies
þ Wire: Thermocouple, RTD & Thermistor
þ Calibrators & Ice Point References
þ Recorders, Controllers & Process Monitors
þ Infrared Pyrometers
þ Data Acquisition &
Engineering Software
þ Communications-Based
Acquisition Systems
þ Plug-in Cards for Apple, IBM
& Compatibles
þ Datalogging Systems
þ Recorders, Printers & Plotters
PRESSURE/STRAIN AND FORCE
þ
þ
þ
þ
Transducers & Strain Gauges
Load Cells & Pressure Gauges
Displacement Transducers
Instrumentation & Accessories
FLOW/LEVEL
þ Rotameters, Gas Mass Flowmeters
& Flow Computers
þ Air Velocity Indicators
þ Turbine/Paddlewheel Systems
þ Totalizers & Batch Controllers
pH/CONDUCTIVITY
þ pH Electrodes, Testers & Accessories
þ Benchtop/Laboratory Meters
þ Controllers, Calibrators, Simulators
& Pumps
þ Industrial pH & Conductivity Equipment
M-2876/0799
HEATERS
þ
þ
þ
þ
þ
Heating Cable
Cartridge & Strip Heaters
Immersion & Band Heaters
Flexible Heaters
Laboratory Heaters
ENVIRONMENTAL
MONITORING AND CONTROL
þ
þ
þ
þ
þ
Metering & Control Instrumentation
Refractometers
Pumps & Tubing
Air, Soil & Water Monitors
Industrial Water & Wastewater
Treatment
þ pH, Conductivity & Dissolved Oxygen
Instruments
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement