MOM5C - Multi Output Power Distribution Module for Access Control Overview:

MOM5C - Multi Output Power Distribution Module for Access Control Overview:
MOM5C - Multi Output Power Distribution
Module for Access Control
Rev. 012100
Overview:
The MOM5C multi output power distribution module converts one (1) non-power limited DC voltage input to five (5)
power limited outputs. Each output will route power to a variety of access control hardware and devices which includes
Mag Locks, Electric Strikes, Magnetic Door Holders, etc... These outputs will operate in both fail-safe and fail-secure
modes. Controlled trigger input is achieved through normally open (NO) or normally closed (NC) supervised input or
the polarity reversal from an FACP (Fire Alarm Control Panel). A form “C” dry output relay will enable HVAC
Shutdown, Elevator Recall or trigger auxiliary devices.
Specifications:
Agency Listings:
• UL Listed for Access Control
System Units (UL294),
Standard for Safety for Fire Protective
Signaling Systems (UL1481)
• NYC Department of Buildings Approved (MEA)
• California State Fire Marshal Approved (CSFM)
• NFPA72 compliant.
Input:
• 12VDC or 24VDC from power supply.
Output:
• 12VDC or 24VDC selectable outputs.
• Five (5) individual power limited class 2 outputs.
• Current limit is 2 amp @ 12VDC or 24VDC per output.
Visual Indicators:
• Red LED’s indicate condition of each power output.
• Power & input trigger LED’s.
Supervision:
• Fire Alarm Panel or Access Control System trigger
inputs. (NO or NC supervised trigger input and
polarity reversal trigger input).
• Power fail supervision relay (Form “C” contact rated
1 amp @ 28VDC).
Special Features:
• Will interface with most UL Listed Power Supplies
Enclosure Dimensions:
8”H x 7.25”W x 3.5”D
Current Draw:
Input Voltage
12VDC
24VDC
• Output relay indicates that unit is triggered.
(Form “C” contact rated 1 amp @ 28VDC).
Stand-by
0.024 amp
0.026 amp
Alarm
0.066 amp
0.074 amp
Installation Instructions:
1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the two fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 4).
2. Connect the DC of the power supply to the terminals marked [-- DC Input +] carefully observing polarity.
3. Connect door strikes (fail-secure) positive to terminals marked [1 thru 5 Pos. (+) DC Output (Alarm)]
and negative to [NEG1] thru [NEG5] (fig. 7, pg. 4).
4. Connect mag locks, door holders (fail-safe) positive to terminals marked [6 thru 10 Pos. (+) DC Output (Stand-by)]
and negative to [NEG1] thru [NEG5] (fig. 7, pg. 4).
5. To trigger the MOM5C from a FACP connect signaling circuit of FACP to terminals marked [- INPUT +].
Polarity is shown in alarm condition. Connect the wires on opposite sides of the screw.
6. To trigger the MOM5C using a supervised dry contact connect a 2.2K resistor in series to terminals marked
[TRIGGER] for a NC (Normally Closed) trigger input or connect a 2.2K resistor in parallel to terminals marked
[TRIGGER] for NO (Normally Open) trigger input (fig. 7, pg. 4).
7. Connect the auxiliary devices that are to be triggered by the MOM5 to terminals marked [Dry Output]:
For Normally Open operation connect wires to the terminals marked [NO & C].
For Normally Closed operation connect wires to the terminals marked [NC & C].
Note: This relay will energize when the MOM5C is triggered.
8. Connect trouble reporting device to the terminals marked [Power Fail].
For Normally Open operation connect wires to the terminals marked [NO & C].
For Normally Closed operation connect wires to the terminals marked [NC & C].
Note: This relay will switch when power is lost to the MOM5C.
MOM5C
-1-
LED Diagnostic Table:
LED
Power (Green)
Trigger (Green)
Outputs (Red)
ON
Normal operation.
MOM5 triggered (alarm condition).
Output tripped due to a short circuit or overload condition.
OFF
Loss of power to MOM5.
MOM5 in stand-by (non-alarm condition).
Normal operation.
Terminal Identification:
Terminal Legend
-- DC INPUT +
TRIGGER
Function/Description
12VDC or 24VDC from power supply.
This circuit is supervised by a 2.2K EOL resistor. Initiating a short or open will
cause power to be dropped to all terminals marked [Pos. (+) DC Output (Stand-by)]
and supply power to all terminals marked [Pos (+) DC Output (Alarm)].
Applying voltage to terminals marked [-- Input +] from the FACP signaling circuit in
polarity shown will yield the same results as initiating trigger (mentioned above).
Supplies constant negative (-) voltage.
Supplies positive (+) voltage when either input trigger is activated.
-- INPUT +
NEG1 thru NEG5
POS (+) DC OUTPUT
(ALARM)
POS (+) DC OUTPUT
(STANDBY)
NC, C, NO
DRY OUTPUT
Supplies positive (+) voltage in normal condition.
Power is removed when either input trigger is activated.
When the MOM5 is triggered the terminals marked [C and NO] will close and the
terminals marked [C and NC] will open. This output is used to trip auxiliary devices.
e.g. HVAC Shutdown, Elevator Recall etc...
Form “C” contacts used for signaling when no voltage is present at [-- DC input +]
terminals. Under normal conditions, terminals marked [NO and C] are open,
and terminals marked [NC and C] are closed. A occurrence of trouble condition causes
terminals marked [NO and C] to closed and [NC and C] to open.
NC, C, NO
POWER FAIL
Typical Application Diagrams:
(+)
(-)
MOM5C module shown with wet and/or dry normally open
trigger inputs (Non-Latching):
DC VOLTAGE INPUT
FROM FACP SIGNALING
OUTPUT OR ACCESS
CONTROL DEVICE
-- INPUT +
-- INPUT +
Fig. 1 - MOM5C module shown with wet and/or dry normally
closed trigger inputs (Non-Latching):
(+)
(-)
DC VOLTAGE INPUT
FROM FACP SIGNALING
OUTPUT OR ACCESS
CONTROL DEVICE
NORMALLY CLOSED (NC)
INPUT FROM FACP
OR ACCESS CONTROL DEVICE
EOL 2.2K
TRIGGER
TRIGGER
EOL 2.2K
NORMALLY OPEN (NO)
INPUT FROM FACP
OR ACCESS CONTROL DEVICE
(+)
(--)
DC VOLTAGE INPUT FROM
FACP SIGNALING
OUTPUT OR ACCESS
CONTROL DEVICE
-- INPUT +
-- INPUT +
Fig. 2 - Two (2) or more MOM5C modules shown with wet and/or dry normally closed trigger inputs (Non-Latching):
TRIGGER
TRIGGER
EOL 2.2K
NORMALLY CLOSED (NC)
INPUT FROM FACP OR
ACCESS CONTROL DEVICE
TRIGGER
LED
NC C NO NC C NO
DRY OUTPUT POWER FAIL
POWER
ON LED
EOL 2.2K
TRIGGER
LED
NC C NO NC C NO
DRY OUTPUT POWER FAIL
POWER
ON LED
TO TRIGGER INPUT
OF NEXT MOM5
-2-
MOM5C
Typical Application Diagrams:
Fig. 3 - Two (2) or more MOM5C modules shown with wet and/or dry normally open trigger inputs (Non-Latching):
-- INPUT +
DC VOLTAGE INPUT FROM
FACP SIGNALING
OUTPUT OR ACCESS
CONTROL DEVICE
EOL 2.2K
TRIGGER
(--)
TRIGGER
-- INPUT +
(+)
EOL 2.2K
NORMALLY OPEN (NO)
INPUT FROM FACP OR
ACCESS CONTROL DEVICE
TRIGGER
LED
POWER
ON LED
NC C NO NC C NO
DRY OUTPUT POWER FAIL
TRIGGER
LED
NC C NO NC C NO
DRY OUTPUT POWER FAIL
POWER
ON LED
TO TRIGGER INPUT
OF NEXT MOM5
(+)
(-)
MOM5C module shown with with wet and/or dry
normally open fire alarm trigger inputs
(Latching with Manual Reset):
DC VOLTAGE INPUT
FROM FACP SIGNALING
OUTPUT
-- INPUT +
-- INPUT +
Fig. 4 - MOM5C module shown with with wet and/or dry
normally closed fire alarm trigger inputs (Latching with
Manual Reset):
(+)
(-)
DC VOLTAGE INPUT
FROM FACP SIGNALING
OUTPUT
TRIGGER
LED
NC C NO NC C NO
DRY OUTPUT POWER FAIL
TRIGGER
TRIGGER
EOL 2.2K
NORMALLY
OPEN (NO)
INPUT FROM
FACP SIGNALING
OUTPUT
POWER
ON LED
EOL 2.2K
NORMALLY CLOSED (NC)
INPUT FROM FACP
SIGNALING OUTPUT
TRIGGER
LED
NORMALLY
CLOSED (NC)
RESET
NC C NO NC C NO
DRY OUTPUT POWER FAIL
POWER
ON LED
NORMALLY
OPEN (NO)
RESET
(--)
DC VOLTAGE INPUT FROM
FACP SIGNALING
OUTPUT OR ACCESS
CONTROL DEVICE
-- INPUT +
(+)
TRIGGER
TRIGGER
-- INPUT +
Fig. 5 - Two (2) MOM5C modules shown with wet and/or dry normally closed fire alarm trigger inputs
(Latching with Manual Reset):
EOL 2.2K
EOL 2.2K
NORMALLY CLOSED (NC)
INPUT FROM FACP OR
ACCESS CONTROL
DEVICE
TRIGGER
LED
NC C NO NC C NO
DRY OUTPUT POWER FAIL
POWER
ON LED
TRIGGER
LED
NC C NO NC C NO
DRY OUTPUT POWER FAIL
POWER
ON LED
NORMALLY OPEN
(NO) RESET
MOM5C
-3-
-3-
Fig. 6 - Two (2) MOM5C modules shown with wet and/or dry normally open fire alarm trigger inputs (Latching with Manual Reset):
TRIGGER
-- INPUT +
(--)
DC VOLTAGE INPUT FROM
FACP SIGNALING
OUTPUT OR ACCESS
CONTROL DEVICE
TRIGGER
-- INPUT +
(+)
EOL
2.2K
EOL 2.2K
NORMALLY OPEN (NO)
INPUT FROM FACP OR
ACCESS CONTROL DEVICE
TRIGGER
LED
POWER
ON LED
NC C NO NC C NO
DRY OUTPUT POWER FAIL
TRIGGER
LED
POWER
ON LED
NC C NO NC C NO
DRY OUTPUT POWER FAIL
NORMALLY
CLOSED (NC)
RESET
Fig. 7
NEG1
NEG2
NEG3
NEG4
NEG5
FROM FACP
SIGNALING
OUTPUT
DC INPUT +
-- INPUT +
DOOR STRIKE
(FAIL-SECURE)
12VDC or 24VDC
FROM POWER SUPPLY
--+
FACP
EOL
MOM5
2.2K EOL
TRIGGER
NC
TRIGGER
INPUT
MAG LOCK
(FAIL-SAFE)
2
3
4
5
POS (+) DC OUTPUT (ALARM)
6
7
8
9
10
POS (+) DC OUTPUT (STANDBY)
TRIGGER
LED
NC C NO NC C NO
DRY OUTPUT POWER FAIL
POWER
ON LED
TRIGGER
1
2.2K
EOL
NO
TRIGGER
INPUT
Enclosure Dimensions:
8”H x 7.25”W x 3.5”D
TOP ONLY
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
website: www.altronix.com, e-mail: [email protected], Lifetime Warranty, Made in U.S.A.
IIMOM5C - 120601
L13F
-4-
MEMBER
MOM5C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement