datasheet for BL-HW133

datasheet for BL-HW133
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BL-HW133-TRB
Features:
Package Dimensions:
1. Emitted Color : Pure Green
2. Lens Appearance : Water Clear.
3. Mono-color type.
4. 3.2x1.6x1.1mm(1206) standard package.
5. Suitable for all SMT assembly methods.
6. Compatible with infrared and vapor phase
reflow solder process.
7. Compatible with automatic placement
equipment.
8. This product doesn’t contain restriction
Substance, comply ROHS standard.
Applications:
1.
NOTES:
1.All dimensions are in millimeters (inches).
2.Tolerance is ±0.10mm (0.004”) unless otherwise specified.
3.Specifications are subject to change without notice.
Automotive : Dashboards, stop lamps,
turn signals.
2.
Backlighting : LCDs, Key pads advertising.
3.
Status indicators : Comsumer & industrial
electronics.
4. General use.
Absolute Maximum Ratings(Ta=25
Parameter
)
Symbol
Rating
Unit
Power Dissipation
Pd
100
mW
Forward Current
IF
30
mA
IFP
100
mA
VR
5
V
Peak Forward Current
Reverse Volage
1
Operating Temperature
Topr
-25 ~80
-
Storage Temperature
Tstg
-30 ~85
-
Soldering Temperature
Tsol
See Page6
-
1 Condition for IFP is pulse of 1/10 duty and 0.1msec width.
Ver.1.1 Page 1 of 7
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BL-HW133-TRB
Electrical and optical characteristics(Ta=25 )
Parameter
Symbol
Condition
Min.
Typ.
Max.
Unit
Forward Voltage
Vf
IF=20mA
-
2.2
2.6
V
Luminous Intensity
Iv
IF=20mA
1.6
3.0
-
mcd
560
-
nm
565
nm
Peak Wave Length
p
IF=20mA
-
Dominant Wave Length
d
IF=20mA
555
IF=20mA
-
25
-
nm
IF=20mA
-
120
-
deg
Spectral Line Half-width
Veiwing Angle
2
1/2
Typical Electro-Optical Characteristics Curves
Fig.2 Forward current derating curve
Fig.1 Relative intensity vs. wavelength
vs. ambient temperature
1.0
60
Forward current (mA)
Relative radiant intensity
50
0.5
40
30
20
10
0
0
510
560
20
610
Wavelength (nm)
60
80
100
Fig.4 Relative luminous intensity vs.
ambient temperature
Fig.3 Forward current vs. forward voltage
50
3.0
2.5
Relative Luminous intensity
(Normalized @20mA)
40
Forward current (mA)
40
Ambient temperature Ta( C)
30
20
2.0
1.5
1.0
10
0.5
0
1
2
3
4
0
-40
5
-20
Forward voltage(V)
0
Fig.5 Relative luminous intensity
vs. forward current
40
60
Fig.6 Radiation diagram
0
2.0
10
20
30
1.5
Relative radiant intensity
Relative luminous intensity (@20mA)
20
Ambient temperature Ta( C)
1.0
0.5
1.0
40
0.9
50
0.8
60
70
0.7
80
90
0
10
20
30
40
50
0.5
0.3
0.1
0.2
0.4
0.6
Forward current (mA)
Ver.1.0 Page 2 of 7
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BL-HW133-TRB
Tapping and packaging specifications(Units: mm)
USER DIRECTION OF FEED
13.0± 0.5
1.27± 0.1
1.5± 0.1
2.0± 0.05
4.0 ± 0.1
TRAILER
LEADER
0.3
FIXING TAPE
NOTE: 3000 pcs PER REEL
Package Method:(unit:mm)
12 bag/box
3000 pcs/reel
215
Bar Code Label
245
230
220
Aluminum Foil Bag
179± 1
13.0± 0.5
71.0± 1
8.0 ± 0.3
3.5 ± 0.05
CATHODE
4.0 ± 0.1
3.5± 0.1
END
5.3 ± 0.05
START
1.75 ± 0.1
ANODE
1.88± 0.1
167
645
6 box/carton
230
334
Ver.1.0 Page 3 of 7
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BL-HW133-TRB
Bin Limits
I n t e n s i t y B i n L i m i ts ( A t 2 0 m A )
BIN CODE
Min. (mcd)
E
1.4
x
2.8
F
2.1
4.2
G
3.2
6.3
H
4.8
9.4
Min. (nm)
Max. (nm)
9
555
559
0
557
561
1
559
563
2
561
565
C o l o r B i n L i m i ts ( A t 2 0 m A )
BIN CODE
B IN
Max. (mcd)
x
Color BIN CODE
Intensity BIN CODE
Ver.1.0 Page 4 of 7
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BL-HW133-TRB
Reliability Test
Classification
Test Item
Reference Standard
Operation Life MIL-STD-750:1026
MIL-STD-883:1005
JIS-C-7021
:B-1
High
Temperature MIL-STD-202:103B
High Humidity JIS-C-7021
:B-11
Endurance
Storage
Test
High
MIL-STD-883:1008
Temperature
JIS-C-7021
:B-10
Storage
Low
Temperature JIS-C-7021
:B-12
Storage
Temperature MIL-STD-202:107D
Cycling
MIL-STD-750:1051
MIL-STD-883:1010
JIS-C-7021
:A-4
Thermal Shock MIL-STD-202:107D
Environmental
MIL-STD-750:1051
Test
MIL-STD-883:1011
Solder
MIL-STD-202:201A
Resistance
MIL-STD-750:2031
JIS-C-7021
:A-1
Test Conditions
Connect with a power If=20mA
Ta=Under room temperature
Test time=1,000hrs
Ta=+65 ±5
RH=90%-95%
Test time=240hrs
Result
0/20
0/20
High Ta=+85 ±5
Test time=1,000hrs
0/20
Low Ta=-35 ±5
Test time=1,000hrs
0/20
-35
~ +25
~ +85
60min 20min
60min
Test Time=5cycle
~ +25
20min
-35 ±5
~+85 ±5
20min
20min
Test Time=10cycle
Preheating
140 -160 ,within 2 minutes.
Operation heating
260 (Max.), within 10seconds. (Max.)
0/20
0/20
0/20
Judgment criteria of failure for the reliability
Measuring items
Forward voltage
Reverse current
Luminous intensity
Note:
Symbol
VF ( V)
IR(uA)
Iv ( mcd )
Measuring conditions
IF=20mA
VR=5V
IF=20mA
1.U means the upper limit of specified characteristics.
Judgement criteria for failure
Over Ux1.2
Over Ux2
Below SX0.5
S means initial value.
2.Measurment shall be taken between 2 hours and after the test pieces have been returned to
normal ambient conditions after completion of each test.
Ver.1.0 Page 5 of 7
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BL-HW133-TRB
Soldering :
1. Manual Of Soldering
The temperature of the iron tip should not be higher than 300
seconds per solder-land is to be observed.
(572
) and Soldering within 3
2. Reflow Soldering
Preheating : 140 ~160 ±5 ,within 2 minutes.
Operation heating : 260 (Max.) within 10 seconds.(Max)
Gradual Cooling (Avoid quenching).
10 SEC. MAX.
Temperature
260
140~160
MAX.
4
4
/SEC. MAX.
/SEC. MAX.
OVER 2 MIN.
Time
DIP soldering (Wave Soldering) :
Preheating : 120 ~150 ,within 120~180 sec.
Operation heating : 245
5
within 5 sec.260
Gradual Cooling (Avoid quenching).
(Max)
Temperature
Soldering heat Max. 260
245
120~150
within 5 sec.
Preheat
120~180 sec.
Time
Handling :
Care must be taken not to cause to the epoxy resin portion of BRIGHT LEDs while it is exposed to
high temperature.
Care must be taken not rub the epoxy resin portion of BRIGHT LEDs with hard or sharp article such
as the sand blast and the metal hook.
Ver.1.0 Page 6 of 7
BRIGHT LED ELECTRONICS CORP.
SINCE 1981
BL-HW133-TRB
Notes for designing:
Care must be taken to provide the current limiting resistor in the circuit so as to drive the BRIGHT
LEDs within the rated figures. Also, caution should be taken not to overload BRIGHT LEDs with
instantaneous voltage at the turning ON and OFF of the circuit.
When using the pulse drive care must be taken to keep the average current within the rated figures.
Also, the circuit should be designed so as be subjected to reverse voltage when turning off the
BRIGHT LEDs.
Storage:
In order to avoid the absorption of moisture, it is recommended to solder BRIGHT LEDs as soon as
possible after unpacking the sealed envelope.
If the envelope is still packed, to store it in the environment as following:
(1) Temperature : 5 -30 (41 )Humidity : RH 60 Max.
(2) After this bag is opened, devices that will be applied to infrared reflow, vapor-phase reflow, or
equivalent soldering process must be:
a. Completed within 24 hours.
b. Stored at less than 30% RH.
(3) Devices require baking before mounting, if:
(2) a or (2) b is not met.
(4) If baking is required, devices must be baked under below conditions:
12 hours at 60 ±3 .
Package and Label of Products:
(1) Package: Products are packed in one bag of 3000 pcs (one taping reel) and a label is attached
on each bag.
(2) Label:
BRIGHT LED LOGO
Part No.
Quantity
BIN.
Sealing Date
x
xx
xx
Year Month
xx
Day
Manufacture Location
Ver.1.0 Page 7 of 7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement