Furse Catalogue - Lightning Protection Pages Furse Catalogue

Furse Catalogue - Lightning Protection Pages Furse Catalogue
Lightning protection
Lightning protection
Lightning protection
Introduction to lightning protection
Introduction to lightning protection
Guidance on display of product information
How to apply lightning protection components
Conductors
Introduction
Bare conductor
Tinned conductor
Bimetallic cable
Hard drawn bar
Flexible braid
PVC covered conductor
LSOH covered conductor
Lead covered conductor
Anti-vandal conductor guard
Air termination
Air rods
Air rod bases & saddles
Rod brackets
Rod to conductor coupling
Multiple point
Strike pad
Free standing air termination
Conductor network
Metallic conductor clips
Non-metallic conductor clips
Standing seam clips
Puddle flange
Holdfasts
Conductor clamps
Test clamps
Bimetallic connectors
Oxide inhibiting compound
Expansion braid bonds
Accessories
22 - 25
22
23
24 - 25
26 - 39
27 - 28
29 - 31
31
32
32
33 - 34
35 - 37
38
38
39
40 - 49
41
42 - 43
44
44
45
45
46 - 49
50 - 74
51 - 53
54 - 59
60
61
61 - 63
64 - 67
67 - 69
70
71
71
72 - 74
21
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Lightning protection
Introduction
Introduction to structural lightning protection
When designing a structural lightning protection system using the Faraday Cage principle, it is possible
to use one or more of a variety of available conductor systems; namely flat tape, solid circular or cable
& wire (stranded).
The decision about which type to use is often based more on country-specific historical preferences or aesthetic
considerations than the superiority of one type over another. High quality Furse conductors, plus appropriate
fittings, are available for all three systems.
Flat tape conductor system
Flat tape conductors are easy to install, with no need to straighten
for a neat finish. Available in copper or aluminium, flat tape can be
installed bare or with a choice of PVC coverings, to enable the tape
to blend with modern building fabrics.
Tinned copper tape is also available for applications that require
additional protection measures, and copper braid is available for
use where flexibility is necessary, e.g. on moving installations like
gates or doors.
Furse copper tape is approved to BS EN 13601, whilst Furse
aluminium tape is approved to BS EN 755-5.
Solid circular conductor system
Solid circular conductors can be used in applications where
aesthetic considerations are important.
The 8 mm diameter solid circular range is less conspicuous than the
flat tape system, and lends itself much better to being concealed.
Available in copper or aluminium, solid circular conductors can also
have PVC coverings.
A coil of circular conductor can be quickly installed, being easy to
bend in any plane, and only needing a straightening tool to give a
very neat finish.
Furse copper solid circular conductor is approved to BS EN 13601,
whilst Furse aluminium solid circular conductor is approved to
BS EN 755-5.
Stranded conductor system
The Furse range of soft drawn stranded conductors is available in
copper, either bare or PVC insulated, and complies with the US
standard NFPA 780.
Furse soft drawn stranded conductor is approved to BS EN 60228,
whilst our PVC insulated stranded conductor is approved to
BS 6004.
The Furse range of conductors is complemented by a complete range of fittings, including clips, clamps, holdfasts
and bimetallic connectors.
22
Fittings are designed to conform to the BS EN 50164 series of product standards governing performance of
lightning protection components which form part of an external lightning protection system (see also
pages 284-285).
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Introduction
Lightning protection
Product selection
Lightning protection products shown in this catalogue include where appropriate a range of quick reference icons
to define their conductor compatibility, installation requirements and their testing standard.
These icons, as well as a sample product page, are shown below.
The icon bar above each product defines the appropriate main conductor system to which the product can
be connected.
Therefore, where items 1 , 2 , 3 are highlighted in full, the product is suitable for connection to the main
conductor system shown (see below).
Icons defining installation requirements and product testing feature under the product text.
These are shown in the example below, and on product pages as
6 - torque setting.
1
Component is suitable for
use with flat tape conductor
in sizes shown
1
4
- testing standard,
3
Component is suitable for
use with solid circular
conductor in sizes shown
- fixings required, and
Square clamp
2
2
5
NEW
Conductor
size
Material
Weight
each
Part
No.
25 x 3 mm
Copper
0.12 kg
CT105-H†
25 x 6 mm
Copper
0.30 kg
CT110-H†
50 x 6 mm
Copper
0.60 kg
CT115-H†
25 x 3 mm
Aluminium
0.06 kg
CT005-H
25 x 6 mm
Aluminium
0.17 kg
CT010-H
CT105-H
Manufactured from high quality copper and aluminium alloys. Simple
to install, providing an effective low resistance connection between
overlapping tapes to allow cross, tee, through and right angle joints to
be formed.
BS EN 50164-1 Class H
†
UL96 (CT105H, CT110-H, CT115-H)
3
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005 or SW105) and wall plugs (Part no. PS305) - see Accessories
page 72.
Component is suitable for
use with stranded conductor
in sizes shown
Tightening torque 5 Nm
Crossover clamp
4
Component has been
tested to the quoted
standard (BS/BS EN/IEC/UL)
4
CX105-H
5
Component requires
additional fixings as
advised to enable
installation
5
Conductor
size
Material
Weight
each
Part
No.
25 x 3 mm
Copper
0.09 kg
CX105-H
25 x 3 mm
Aluminium
0.03 kg
CX005-H
Manufactured from high quality copper and aluminium alloys. Simple to
install, providing an effective low resistance connection between
overlapping tapes to allow cross joints to be formed.
BS EN 50164-1 Class H
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005 or SW105) and wall plugs (Part no. PS305) - see Accessories
page 72.
Tightening torque 5 Nm
6
6
Component should be
tightened to the torque
setting advised
Special component design and manufacture
For the vast majority of installations, the standard range of conductors
and lightning protection components is highly suitable for completing a
lightning protection system. On occasion however, an installation may
include a special requirement needing a non-standard component.
Our technical services team is adept at developing and designing special
components to customer needs, which on approval can be manufactured
in the quantity specified for the project.
If you consider your lightning protection system will require development
of a special component (e.g. new sizing or revised design), please do not
hesitate to contact us to discuss your needs.
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
23
Lightning protection
Conductors
The first choice faced by the designer of a structural
lightning protection system is the type of conductor
system to be used.
Choose the material required, i.e. copper or aluminium.
Choose the type of conductor required, i.e. flat tape,
solid circular or stranded.
Conductor network
The conductor network is the
means of intercepting/carrying
the current of a lightning strike
safely to the earth termination
network. Use the guidelines of
BS EN 62305-1 & 3 for the correct
placement of conductors.
Product selector
Down conductor network
Conductor jointing clamps
Select a component for the
interconnection of multiple
conductors or for changes of
direction. Jointing clamps will
ensure a low resistance, corrosion
resistant connection between air
termination and down conductors.
Test clamps
In order to allow periodic
disconnection and testing of the
earth termination network, select a
test clamp to be placed within the
run of each down conductor.
Fixings
Select the correct system of fixings
for each part of the conductor
system. Fixings are available for a
wide range of modern construction
materials, e.g. brick, stone, plastic
and metal.
Air termination network
The air termination network is the point of connection
for a lightning strike. It typically consists of a meshed
conductor arrangement covering the roof of the
structure. The mesh size is now determined by
Lightning Protection Level - LPL (see Table 7, page 274).
Air terminals
Use air terminals in the form of
vertical air rods for the protection
of prominent roof top features or
equipment. Use strike pads to
connect and thus expose concealed
conductors.
Air rod bases
Choose the correct air rod base.
This will ensure that the vertical air
rods are both solidly fixed to the
fabric of the structure and have a
low resistance connection to the
conductor network.
Interconnection components
24
Crossover clamps have been specially
designed for use where conductors
cross as part of a roof network.
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Product selector
Earth termination network
Lightning protection
Earth inspection pits
The means of dissipating the current to the general
mass of earth.
Select an earth inspection pit to
protect the earth electrode
connections. High strength pits are
available in plastic and concrete.
Earth electrodes
Choose an earth electrode to suit
the system design i.e. Type A, Type
B or foundation electrode.
Electrodes can be constructed
individually from earth rods, earth
plates, flat tape, stranded cable or
any combination of these.
Earth rod clamps
Select a high copper content alloy
earth rod clamp for the connection
of the earthing conductor to the
earth rod. In this below ground
application, the clamp must ensure
a good electrical contact and resist
corrosion throughout the lifetime
of the installation.
Equipotential bonding
Bonding is the most commonly employed method of
avoiding the damaging effects of side flashing. All
continuous metalwork should be considered for
bonding. All metallic services, e.g. cable armouring,
gas, water or steam piping, entering the building
should also be bonded as directly as possible to the
earth termination network.
Bonds to metalwork
Select the correct type of
metalwork bond for the
application, i.e. a flat column
face, a circular rainwater pipe or
a ribbed reinforcing bar.
Equipotential bonding SPDs
Designed to prevent dangerous
sparking caused by flashover,
lightning current or equipotential
bonding SPDs must be fitted to
all metallic service lines with ‘live
cores’ entering or leaving the
structure.
Product selector
This illustration is designed to demonstrate the main aspects and
individual components of an external lightning protection system.
It is not intended to represent an actual scheme conforming to a
particular code of practice. The drawing is not to scale.
(1) Conductors
p26-39
(2) Conductor fixings
p50-74
(3) Air terminals
p40-49
(4) Air rod bases
p42-44, 49
(5) Conductor jointing clamps
p64-67
(6) Test clamps
p67-69
(7) Crossover conductor clamp
p64
(8) Earth electrodes
p81-84, 88
(9) Earth rod clamps
p92-94
(10) Earth inspection pits
p87
(11) Bonds
p92-106
(12) Lightning current or
Equipotential bonding SPDs
p182-195
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
25
Conductors
Conductors
Bare conductor
Tinned conductor
Bimetallic cable
Hard drawn bar
Flexible braid
PVC covered conductor
LSOH covered conductor
Lead covered conductor
Anti-vandal conductor guard
29-31
31
32
32
33-34
35-37
38
38
39
Conductors
By far the largest and most important component of any structural lightning protection or earthing
system is the actual conductor.
Selection of the correct conductor type for the installation is highly important, and is likely to be the initial
consideration of a lightning protection or earthing system designer.
A comprehensive range of Furse copper and aluminium conductors are available in each of the main world standard
formats, i.e. flat tape, solid circular and stranded. Additionally each format is available in a variety of conductor sizes,
to meet differing lightning protection and earthing requirements.
Specification will depend on whether the application is for an above ground structural lightning protection system, or
a below ground earthing installation.
Conductors for structural lightning
protection systems
Furse lightning protection conductors are available in
copper and aluminium, and are supplied bare or with
PVC coating (see below). For most installations, copper
is specified due to its high conductivity and anticorrosive properties.
The following sizes are suitable for the majority of
above ground lightning protection systems:
Flat tape conductor:
25 x 3 mm bare tape, or 25 x 3 mm PVC covered tape
Solid circular conductor
8 mm diameter bare or PVC covered solid circular
conductor
Stranded conductor
70 mm2 bare or PVC covered stranded conductor
Conductor colour chart
The choice of a lightning protection conductor is
usually governed by its aesthetic impact on the
structure to be protected. For many people the term
lightning conductor conjures up an image of a
discoloured copper strip running down the spire of a
church. This would clearly be unacceptable to the
owner/architect of a modern structure.
In order to reduce the impact of an external system
Furse offer a range of UV stabilized PVC covered tapes
and solid circular conductors in colours chosen to
match most common building materials.
Standard PVC colours are shown in the chart, right,
with special colours available to order.
Black
18B29*
Green
BS 6746C
Grey
00A07*
Stone
08B23*
White
10B15*
Brown
06C39*
* PVC colours to BS 5252
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
27
Conductors
Conductors for earthing systems
Furse earthing conductors form an integral part of the single earthing arrangement for a structure, whether they
provide the means of connection to the final earth electrode (earth rod or plate), or whether they comprise the earth
electrode itself (through an earth grid or ring earth arrangement).
An earth conductor must be capable of carrying the maximum expected earth fault current and
leakage current likely to occur at a structure.
The size or minimum cross-sectional area of the conductor must
therefore be gauged in accordance with these criteria.
A good earth conductor must also:
●
be able to withstand mechanical damage
●
be compatible with the material of the earth electrode, and
●
resist the corrosive effect of local soil conditions
Furse conductors effectively meet these requirements
and are available in a range of sizes to meet differing
current ratings (see table below).
Copper conductor is recommended as, following
BS 7430, aluminium should not be installed in contact
with soil, nor in damp areas, and it should not be used
to make the final connection to an earth electrode.
Copper conductor ratings
For below ground earthing applications we produce a large range of bare copper, tape and stranded conductors thus
offering the designer of the system the correctly rated conductor without the need to oversize.
The following conductor ratings are based upon the recommendations of BS 7430 with an initial conductor
temperature of 30 °C and a maximum temperature of 250 °C.
Conductor
size
C.S.A.
(mm2)
kA for
1 sec
kA for
3 sec
Conductor
size
C.S.A.
(mm2)
kA for
1 sec
kA for
3 sec
12.5 x 1.5 mm
18.75
3.3
1.9
31 x 6 mm
186
32.7
18.9
12.5 x 3 mm
37.5
6.6
3.8
38 x 3 mm
114
20.1
11.6
20 x 1.5 mm
30
5.3
3.0
38 x 5 mm
190
33.4
19.3
20 x 3 mm
60
10.6
6.1
38 x 6 mm
228
40.1
23.2
37.5
6.6
3.8
40 x 3 mm
120
21.1
12.2
75
13.2
7.6
40 x 4 mm
160
28.2
16.3
25 x 1.5 mm
25 x 3 mm
25 x 2 mm
50
8.8
5.1
40 x 5 mm
200
35.2
20.3
25 x 4 mm
100
17.6
10.2
40 x 6 mm
240
42.2
24.4
25 x 6 mm
150
26.4
15.2
40 x 6.3 mm
252
44.4
25.6
30 x 2 mm
60
10.6
6.1
50 x 3 mm
150
26.4
15.2
30 x 3 mm
90
15.8
9.1
50 x 4 mm
200
35.2
20.3
30 x 4 mm
120
21.1
12.2
50 x 5 mm
250
44.0
25.4
30 x 5 mm
150
26.4
15.2
50 x 6 mm
300
52.8
30.5
31 x 3 mm
93
16.4
9.5
50 x 6.3 mm
315
55.4
32.0
31.5 x 4 mm
126
22.2
12.8
50 x 7 mm
350
61.6
35.5
28
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductors
Bare copper tape
Conductor size
(X x Y)
Weight
per metre
Standard
coil size
Part
No.
12.5 x 1.5 mm
0.17 kg
100 m
TC005
12.5 x 3 mm
0.33 kg
100 m
TC010
20 x 1.5 mm
0.27 kg
100 m
TC015
20 x 3 mm
0.53 kg
50 m
TC020
20 x 3 mm
0.53 kg
100 m
TC020/100
25 x 1.5 mm
0.33 kg
100 m
TC025
25 x 2 mm
0.49 kg
50 m
TC026
25 x 3 mm
0.67 kg
25 m
TC030
25 x 3 mm
0.67 kg
50 m
TC030/50
1” x 1⁄8”
0.67 kg
25 m
TC030-UL†
25 x 4 mm
0.89 kg
50 m
TC035
25 x 6 mm
1.33 kg
40 m
TC040
1
1” x ⁄4”
1.33 kg
40 m
TC040-UL†
30 x 2 mm
0.53 kg
50 m
TC039
30 x 3 mm
0.80 kg
50 m
TC042
30 x 4 mm
1.07 kg
40 m
TC044
30 x 5 mm
1.33 kg
40 m
TC043
31 x 3 mm
0.83 kg
50 m
TC045
31.5 x 4 mm
1.13 kg
40 m
TC048
31 x 6 mm
1.65 kg
30 m
TC050
38 x 3 mm
1.01 kg
50 m
TC055
38 x 5 mm
1.69 kg
30 m
TC060-FU
38 x 6 mm
2.02 kg
25 m
TC065
40 x 3 mm
1.06 kg
40 m
TC067
40 x 4 mm
1.42 kg
30 m
TC066
40 x 5 mm
1.78 kg
25 m
TC071
40 x 6 mm
2.16 kg
25 m
TC068
40 x 6.3 mm
2.24 kg
25 m
TC069
50 x 3 mm
1.33 kg
40 m
TC070
50 x 4 mm
1.78 kg
30 m
TC075
50 x 5 mm
2.22 kg
20 m
TC078
50 x 6 mm
2.68 kg
20 m
TC080†
50 x 6.3 mm
2.80 kg
20 m
TC082
50 x 7 mm
3.08 kg
20 m
TC090
TC030
NEW
NEW
High conductivity copper tape to BS EN 13601
(formerly BS 1432).
†
UL96 (TC030-UL, TC040-UL, TC080)
All bare copper tape sold in full coil lengths only.
29
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductors
Bare aluminium tape
Conductor
size (X x Y)
TA030
Weight
per metre
Standard
coil size
Part
No.
12.5 x 1.5 mm
0.05 kg
50 m
TA005
20 x 3 mm
0.17 kg
50 m
TA020
25 x 3 mm
0.21 kg
50 m
TA030
30 x 3 mm
0.25 kg
50 m
TA042
25 x 6 mm
0.42 kg
50 m
TA040
40 x 6 mm
0.67 kg
50 m
TA068
50 x 6 mm
0.85 kg
50 m
TA080
Aluminium tape to BS EN 755-5.
Bare solid circular
Conductor
material
CD035
Diameter
(A)
Cross-sectional
area
Weight
per metre
Standard
coil size
Part
No.
Copper
8 mm
50.27 mm2
0.44 kg
50 m
CD035
Aluminium
8 mm
50.27 mm2
0.12 kg
50 m
CD080
Copper conductor to BS EN 13601 (formerly BS 1433).
Aluminium conductor to BS EN 755-5.
A
30
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductors
Bare stranded copper cable
Cross-sectional
area
Stranding
No./ mm Ø
Nominal
diameter (A)
Weight
per metre
Part
No.
Soft drawn stranded copper cable
6 mm2
7/1.04
3.12 mm
0.05 kg
CB006
16 mm2
7/1.70
5.10 mm
0.15 kg
CB016
mm2
7/2.14
6.42 mm
0.23 kg
CB025
35 mm2
7/2.52
7.56 mm
0.32 kg
CB035
50 mm2
19/1.78
8.90 mm
0.43 kg
CB050-FU
mm2
19/2.14
10.70 mm
0.62 kg
CB070
95 mm2
19/2.52
12.60 mm
0.86 kg
CB095
mm2
37/2.03
14.21 mm
1.09 kg
CB120
150 mm2
37/2.25
15.75 mm
1.33 kg
CB150-FU
185 mm2
37/2.52
17.64 mm
1.67 kg
CB185
240 mm2
61/2.25
20.25 mm
2.20 kg
CB240
300 mm2
61/2.52
22.68 mm
2.76 kg
CB300-FU
400 mm2
61/2.85
25.65 mm
3.53 kg
CB400-FU
-
0.62 kg
CB070-T*
-
0.64 kg
CB071*
25
70
120
CB070
A
Tinned soft drawn stranded copper cable
70 mm2
19/2.14
NEW
Hard drawn stranded copper cable
70 mm2
7/3.55
* Additional sizes available on request.
Soft drawn stranded copper cable to BS EN 60228.
Hard drawn stranded copper cable to BS 7884.
Tinned copper tape
Conductor size
(X x Y)
Weight
per metre
Standard
coil size
Part
No.
12.5 x 1.5 mm
0.17 kg
100 m
TC225-FU
25 x 3 mm
0.67 kg
50 m
TC230
1
1” x ⁄8”
0.67 kg
50 m
TC230-UL†
30 x 2 mm
0.53 kg
50 m
TC239
25 x 6 mm
1.33 kg
40 m
TC240
31 x 3 mm
0.83 kg
50 m
TC245
38 x 5 mm
1.69 kg
30 m
TC260
50 x 6 mm
2.68 kg
20 m
TC280
TC230
High conductivity copper tape to BS EN 13601
(formerly BS 1432).
†
UL96 (TC230-UL)
31
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductors
Bimetallic cable
AWG
Cross-sectional
area
Nominal
diameter
Stranding
No./AWG
Weight
per metre
Part
No.
50 mm2
9.96 mm
3/5
0.41 kg
BC001
1
40
mm2
8.86 mm
3/6
0.33 kg
BC002
2
35 mm2
7.9 mm
3/7
0.26 kg
BC003
3
25
mm2
7.04 mm
3/8
0.21 kg
BC004
4
20 mm2
6.27 mm
3/9
0.16 kg
BC005
5
16 mm2
5.59 mm
3/10
0.13 kg
BC006
6
10
mm2
4.42 mm
3/12
0.08 kg
BC007
300
150 mm2
15.6 mm
7/4
1.22 kg
BC008
4/0
120
mm2
13.9 mm
7/5
0.97 kg
BC009
3/0
95 mm2
12.3 mm
7/6
0.77 kg
BC010
2/0
70
mm2
11 mm
7/7
0.61 kg
BC011
1/0
50 mm2
9.78 mm
7/8
0.48 kg
BC012
1
40
mm2
8.71 mm
7/9
0.38 kg
BC013
2
35 mm2
7.77 mm
7/10
0.30 kg
BC014
1/0
BC011
40% conductivity supplied as standard. Other sizes also available.
Contact us for details.
Copper/steel cable to ASTM B228.
Hard drawn copper bar
Overall nominal
size (X x Y)
Weight
per metre
Approximate
length
Part
No.
25 x 3 mm
0.67 kg
3m
BA205
25 x 6 mm
1.33 kg
4m
BA210
38 x 6 mm
2.03 kg
4m
BA225
50 x 6 mm
2.67 kg
3m
BA230
50 x 10 mm
4.45 kg
4m
BA235
75 x 6 mm
4.00 kg
4m
BA240
100 x 6 mm
5.38 kg
4m
BA250-FU
2.67 kg
3m
BA231*
Bare hard drawn bar
BA205
Tinned hard drawn bar
50 x 6 mm
* Additional sizes available on request.
Hard drawn high conductivity copper bar to BS EN 12163.
32
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductors
Flexible flat copper braid
Overall nominal
size (X x Y)
Cross-sectional
area
Weight
per metre
Part
No.
12 x 1 mm
6 mm2
0.055 kg
BD020
15 x 1.5 mm
10 mm2
0.096 kg
BD025
19 x 2.5 mm
16 mm2
0.16 kg
BD026
25 x 3 mm
25 mm2
0.25 kg
BD028
25 x 3.5 mm
35 mm2
0.34 kg
BD030
30 x 5 mm
50
mm2
0.49 kg
BD031
32 x 6 mm
70 mm2
0.63 kg
BD027
37 x 6 mm
95 mm2
0.93 kg
BD032
NEW
45 x 6 mm
120 mm2
1.15 kg
BD033
NEW
50 x 8 mm
mm2
1.45 kg
BD034
NEW
6 mm2
0.055 kg
BD020-T
NEW
15 x 1.5 mm
10
mm2
0.096 kg
BD025-T
NEW
19 x 2.5 mm
16 mm2
0.16 kg
BD026-T
NEW
25 x 3 mm
25
mm2
0.25 kg
BD028-T
NEW
25 x 3.5 mm
35 mm2
0.34 kg
BD035
30 x 5 mm
50 mm2
0.49 kg
BD031-T
NEW
32 x 6 mm
70 mm2
0.63 kg
BD027-T
NEW
37 x 6 mm
95 mm2
0.93 kg
BD032-T
NEW
45 x 6 mm
120
mm2
1.15 kg
BD033-T
NEW
50 x 8 mm
150 mm2
1.45 kg
BD034-T
NEW
Bare flat braid
150
BD028
NEW
NEW
Tinned flat braid
12 x 1 mm
Suitable for earth bonding. Also supplied as standard pre-cut and drilled
bonds (see pages 104-105). Other sizes and types of braid can be made to
order. Please contact us for details.
High conductivity copper wire to BS EN 13602
(formerly BS 4109-C101).
33
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductors
Flexible circular copper braid
NEW
Overall nominal
diameter
Cross-sectional
area
Weight
per metre
Part
No.
4.2 mm
6 mm2
0.055 kg
BD006-FU
5.4 mm
10 mm2
0.096 kg
BD010-FU
7 mm
16 mm2
0.16 kg
BD016-FU
8.5 mm
25
mm2
0.25 kg
BD025-FU
10.5 mm
35 mm2
0.34 kg
BD035-FU
11.5 mm
50
mm2
0.49 kg
BD050-FU
14.5 mm
70 mm2
0.63 kg
BD070-FU
mm2
0.93 kg
BD095-FU
4.2 mm
6 mm2
0.055 kg
BD006-FU-T
5.4 mm
10
mm2
0.096 kg
BD010-FU-T
7 mm
16 mm2
0.16 kg
BD016-FU-T
8.5 mm
25
mm2
0.25 kg
BD025-FU-T
10.5 mm
35 mm2
0.34 kg
BD035-FU-T
11.5 mm
50
mm2
0.49 kg
BD050-FU-T
14.5 mm
70 mm2
0.63 kg
BD070-FU-T
mm2
0.93 kg
BD095-FU-T
Bare circular braid
BD070-FU
16 mm
95
Tinned circular braid
16 mm
95
Suitable for earth bonding. Also supplied as standard pre-cut and drilled
bonds (see pages 104-105). Other sizes and types of braid can be made to
order. Please contact us for details.
High conductivity copper wire to BS EN 13602
(formerly BS 4109-C101).
34
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductors
PVC covered copper tape
Conductor size
(X x Y)
Weight
per metre
Standard
coil size
Colour
range
Part
No.
12.5 x 1.5 mm
0.21 kg
50 m
Black
TC100
25 x 3 mm
0.77 kg
25 m
Black
TC105-FU
25 x 3 mm
0.77 kg
25 m
Green*
TC110
25 x 3 mm
0.77 kg
25 m
Grey
TC115-FU
25 x 3 mm
0.77 kg
25 m
Stone
TC120-FU
25 x 3 mm
0.77 kg
25 m
White
TC125-FU
25 x 3 mm
0.77 kg
25 m
Brown
TC130
25 x 3 mm
0.77 kg
50 m
Black
TC105/50
25 x 3 mm
0.77 kg
50 m
Green*
TC110/50
25 x 3 mm
0.77 kg
50 m
Grey
TC115/50
25 x 3 mm
0.77 kg
50 m
Stone
TC120/50
25 x 3 mm
0.77 kg
50 m
White
TC125/50
25 x 3 mm
0.77 kg
50 m
Brown
TC130/50
25 x 6 mm
1.53 kg
40 m
Green*
TC140-FU
50 x 6 mm
2.95 kg
20 m
Green*
TC145
TC105-FU
Other colours and sizes are available to order. Contact us for details. Every
precaution has been taken to ensure the UV stability of PVC coverings, but
as with all plastics, colour variation will occur over time.
High conductivity copper tape to BS EN 13601 (formerly BS 1432).
PVC colours to BS 5252. * Green to BS 6746C.
PVC covered copper solid circular
Conductor Diameter Cross-sectional
material
(A)
area
Weight
per metre
Standard
coil size
Colour
range
Part
No.
Black
CD036
8 mm
50.27 mm2
0.49 kg
50 m
Copper
8 mm
50.27
mm2
0.49 kg
50 m
Grey
CD038
Copper
8 mm
50.27 mm2
0.49 kg
50 m
Stone
CD039
Copper
8 mm
50.27
mm2
0.49 kg
50 m
White
CD040
Copper
8 mm
50.27 mm2
0.49 kg
50 m
Brown
CD041
Copper
CD036
Other colours and sizes are available to order. Contact us for details. Every
precaution has been taken to ensure the UV stability of PVC coverings, but
as with all plastics, colour variation will occur over time.
Copper conductor to BS EN 13601 (formerly BS 1433).
A
PVC colours to BS 5252.
35
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductors
PVC covered aluminium tape
Conductor size
(X x Y)
TA110
Weight
per metre
Standard
coil size
Colour
range
Part
No.
12.5 x 1.5 mm
0.09 kg
50 m
Black
TA100
20 x 3 mm
0. 25 kg
50 m
Black
TA104
25 x 3 mm
0.30 kg
50 m
Black
TA105
25 x 3 mm
0.30 kg
50 m
Green*
TA110
25 x 3 mm
0.30 kg
50 m
Grey
TA115
25 x 3 mm
0.30 kg
50 m
Stone
TA120
25 x 3 mm
0.30 kg
50 m
White
TA125
25 x 3 mm
0.30 kg
50 m
Brown
TA130
Other colours and sizes are available to order. Contact us for details. Every
precaution has been taken to ensure the UV stability of PVC coverings, but
as with all plastics, colour variation will occur over time.
Aluminium tape to BS EN 755-5.
PVC colours to BS 5252. * Green to BS 6746C.
PVC covered aluminium solid circular
Diameter
(A)
CD081
Cross-sectional
area
Weight
per metre
Standard
coil size
Colour
range
Part
No.
8 mm
50.27 mm2
0.18 kg
50 m
Black
CD081
8 mm
50.27 mm2
0.18 kg
50 m
Grey
CD083
8 mm
50.27
mm2
0.18 kg
50 m
Stone
CD084
8 mm
50.27 mm2
0.18 kg
50 m
White
CD085
8 mm
50.27 mm2
0.18 kg
50 m
Brown
CD086
Other colours and sizes are available to order. Contact us for details. Every
precaution has been taken to ensure the UV stability of PVC coverings, but
as with all plastics, colour variation will occur over time.
A
Aluminium conductor to BS EN 755-5.
PVC colours to BS 5252.
36
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductors
Green & yellow PVC insulated copper tape
Conductor size
(X x Y)
Weight
per metre
Standard
coil size
Part
No.
25 x 3 mm
0.79 kg
25 m
TC111-FU
25 x 3 mm
0.79 kg
50 m
TC111/50
High conductivity copper tape to BS EN 13601 (formerly BS 1432).
TC111-FU
PVC colours to BS 6746C.
Green & yellow PVC insulated stranded copper cable
Stranding
No./mm Ø
Weight
per metre
Part
No.
16 mm2
7/1.70
0.19 kg
CC016
25 mm2
7/2.14
0.29 kg
CC025
mm2
7/2.52
0.41 kg
CC035
50 mm2
19/1.78
0.53 kg
CC050
70 mm2
19/2.14
0.73 kg
CC070
95 mm2
19/2.52
1.00 kg
CC095
mm2
37/2.03
1.16 kg
CC120-FU
150 mm2
37/2.25
1.54 kg
CC150-FU
mm2
37/2.52
2.01 kg
CC185
240 mm2
61/2.25
2.49 kg
CC240
300 mm2
61/2.52
3.05 kg
CC300
400 mm2
61/2.85
3.90 kg
CC400-FU
Cross-sectional
area
35
120
185
CC070
PVC covered soft drawn stranded copper cable to BS 6004.
PVC colours to BS 6746C.
37
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductors
LSOH covered copper tape
TC910
Conductor size
(X x Y)
Colour
Weight
per metre
Standard
coil size
Part
No.
25 x 3 mm
Green
0.77 kg
25 m
TC910
25 x 3 mm
Green
0.77 kg
50 m
TC910/50
25 x 6 mm
Green
1.53 kg
40 m
TC940
50 x 6 mm
Green
2.95 kg
20 m
TC980
High conductivity copper tape to BS EN 13601 (formerly BS 1432).
PVC colours to BS 6746C.
Lead covered copper tape
Conductor size
(X x Y)
25 x 3 mm
TC330
Weight
per metre
Standard
coil size
Part
No.
2.56 kg
25 m
TC330
High conductivity copper tape to BS EN 13601 (formerly BS 1432).
38
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductors
Anti-vandal down conductor guard
Length
Weight
each
Part
No.
3000 mm
2.90 kg
AV005
Suitable for use with 25 x 3 mm tape.
AV005
Fix using roundhead wood screws (Part no. SW405) and wall plugs
(Part no. PS305) - see Accessories page 72.
3000 mm
76 mm
16 mm
40 mm
335 mm centres
ø7 mm
39
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Air termination
Air termination
Air rods
Air rod bases & saddles
Rod brackets
Rod to conductor coupling
Multiple point
Strike pad
Free standing air termination
41
42-43
44
44
45
45
46-49
Air termination
Air rod
Rod
length
Rod
diameter
Thread
size
Conductor
material
Weight
each
Part
No.
For use with flat tape
500 mm
15 mm
M16
Copper
0.73 kg
RA215†
1000 mm
15 mm
M16
Copper
1.51 kg
RA225†
1500 mm
15 mm
M16
Copper
2.35 kg
RA230
2000 mm
15 mm
M16
Copper
3.00 kg
RA240
3000 mm
15 mm
M16
Copper
4.70 kg
RA250-FU
500 mm
15 mm
M16
Aluminium
0.29 kg
RA015
1000 mm
15 mm
M16
Aluminium
0.53 kg
RA025
1500 mm
15 mm
M16
Aluminium
0.80 kg
RA030
2000 mm
15 mm
M16
Aluminium
1.06 kg
RA040
3000 mm
15 mm
M16
Aluminium
1.60 kg
RA050
Copper
0.33 kg
RA400-FU
For use with solid circular conductor
500 mm
10 mm
M10
1000 mm
10 mm
M10
Copper
0.65 kg
RA402
500 mm
10 mm
M10
Aluminium
0.11 kg
RA080
1000 mm
10 mm
M10
Aluminium
0.22 kg
RA085
For use with stranded conductor
500 mm
15 mm
M16
Copper
0.73 kg
RA215†
1000 mm
15 mm
M16
Copper
1.51 kg
RA225†
1500 mm
15 mm
M16
Copper
2.35 kg
RA230
2000 mm
15 mm
M16
Copper
3.00 kg
RA240
3000 mm
15 mm
M16
Copper
4.70 kg
RA250-FU
Manufactured from high conductivity hard drawn copper or aluminium,
with rolled threads. Supplied complete with locknut.
“Field Trials in the United States, carried out over many years research have
confirmed that blunt air rods are struck by lightning in preference to taper
pointed air rods.”
“Lightning rod improvement studies” by C B Moore, W Rison, J Mathis, G Aulich. Journal of Applied
Meteorology, May 2000.
RA225 + RA600 + SD105-H
Note: during high winds and extreme weather conditions air rods over 1000 mm long can be
subjected to fatigue mechanisms. It is therefore recommended that additional supports are
considered before installation.
Air rod shown with multiple point accessory,
connecting to flat tape conductor system
BS EN 50164-2
†
UL96 (RA215, RA225)
41
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Air termination
Air rod base
Rod
diameter
NEW
Thread
size
Maximum
conductor width
Conductor
material
Weight
each
Part
No.
15 mm
M16
25 mm
Copper
0.43 kg
SD105-H†
15 mm
M16
25 mm
Aluminium
0.14 kg
SD003-H
15 mm
M16
50 mm
Copper
0.7 kg
SD120*
* Not as illustrated (drawing available on request).
SD105-H
Manufactured from high quality copper and aluminium alloys. Simple
to install, providing an effective connection between air rod and air
termination tape.
BS EN 50164-1 Class H
†
UL96 (SD105-H)
Fix using countersunk wood screws (Part no. SW005 or SW105) and
wall plugs (Part no. PS305) - see Accessories page 72.
41 mm
øM16
62 mm
80 mm
Air rod base
Conductor
diameter
Thread
size
Conductor
material
Weight
each
Mounting
plate
Part
No.
8 mm
M10
Copper
0.30 kg
Horizontal
SD305
8 mm
M10
Copper
0.30 kg
Vertical
SD307
8 mm
M10
Aluminium
0.11 kg
Horizontal
SD005
8 mm
M10
Aluminium
0.11 kg
Vertical
SD007
Manufactured from high quality copper and aluminium alloys. Simple to
install, providing an effective connection between an air rod and solid
circular air termination conductor in either the horizontal or vertical plane.
SD307
BS EN 50164-1 Class H
Fix using countersunk wood screws 11⁄2” No. 10 or M6
(Part no. SW005 or SW105) and wall plugs (Part no. PS305) see Accessories page 72.
SD305
Tightening torque 15 Nm
M10
65 mm
42
50 mm
64 mm
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Air termination
Flat saddle
Conductor
diameter
Rod
diameter
Thread
size
Conductor
material
Weight
each
Part
No.
50 mm2
15 mm
M16
Copper
1.03 kg
SD155
mm2
15 mm
M16
Copper
0.95 kg
SD160
95 mm2
15 mm
M16
Copper
0.95 kg
SD165
70
Manufactured from a high quality copper alloy. Simple to install, providing
an effective connection between air rod and stranded conductors.
SD160
85 mm
BS EN 50164-1 Class H
55 mm
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005) and wall plugs (Part no. PS305) - see Accessories page 72.
Tightening torque 12 Nm
64 mm
Ridge saddle
Rod
diameter
15 mm
Thread
size
Maximum
conductor width
Conductor
material
Weight
each
Part
No.
M16
31 mm
Copper
1.07 kg
SD115
For supporting lightning conductor air rods on ridges.
BS EN 50164-1 Class H
Fix using countersunk wood screws 11⁄2” No. 10 or M6
(Part no. SW005 or SW105) and wall plugs (Part no. PS305) see Accessories page 72.
SD115
150 mm
Tightening torque 15 Nm
100 mm
71 mm
43
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Air termination
Rod brackets
Rod
diameter
Rod
material
Weight
each
Part
No.
15 mm
Copper
0.90 kg
BR105
15 mm
Aluminium
0.28 kg
BR005
Manufactured from high quality copper and aluminium alloys. Simple to
install, providing an effective means of mounting an air rod on a vertical
surface e.g. chimney stack. Use in conjunction with a rod to flat tape, or rod
to stranded conductor coupling.
BR105
Fix using roundhead wood screws 11⁄2” x no. 12 or M8 and
wall plugs.
Rod to conductor coupling
Conductor
size
Rod
diameter
Thread
size
Rod
material
Weight
each
Part
No.
For use with flat tape conductor
25 x 3 mm
15 mm
M16
Copper
0.23 kg
CG600
25 x 3 mm
15 mm
M16
Aluminium
0.08 kg
CG500
For use with stranded conductor
CG600
50-70 mm2
15 mm
M16
Copper
0.25 kg
CG705
95 mm2
15 mm
M16
Copper
0.25 kg
CG710
Manufactured from high quality copper and aluminium alloys. Provides an
effective connection between air rod and air termination tape or stranded
air termination conductor. Use in conjunction with rod brackets.
BS EN 50164-1 Class H
CG705
Tightening torque 7 Nm (tape); 6 Nm (stranded)
44
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Air termination
Multiple point
Rod
diameter
Conductor
material
Weight
each
Part
No.
15 mm
Copper
0.27 kg
RA600
15 mm
Aluminium
0.10 kg
RA500
NEW
Manufactured from high conductivity hard drawn copper or aluminium,
suitable for use with air rods on page 41.
RA600
RA500
Strike pad
Conductor
material
Weight
each
Part
No.
Copper
0.41 kg
PL010
Aluminium
0.13 kg
PL005
Copper stem for use with PL010
0.07 kg
SM010
PL010
Manufactured from high quality copper and aluminium alloys. Designed to
provide an exposed attractive point on conductor systems hidden/embedded
in the building’s fabric e.g. below the tiles of a pitched roof.
Supplied with setscrew for attachment of lightning conductors.
Ø112 mm
45
10 mm
20 mm
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Air termination
Free standing air termination
Furse free standing interception air rods are designed to protect rooftop mounted or exposed equipment,
such as air conditioning units or photovoltaic panels, from a direct lightning strike.
Free standing interception air rods are easily constructed from a small range of components including air rod or
interception pole, support frame and concrete base, to create a complete unit which when connected to the air
termination network provides a highly versatile and effective lightning protection solution.
Interception air rod
(0.5 m to 2 m height)
●
Copper or aluminium
air rod
●
Circular concrete base
●
Rod connects directly
into base
Interception air rod
(4.5 m to 5.5 m height)
Interception air rod
(3 m to 4 m height)
●
2 piece interception
pole with square
support frame
●
2 piece interception
pole with tripod
support frame
●
4 square concrete
bases (or 8 doublestacked for higher
wind speeds)
●
3 circular
concrete bases
Interception air rod
(6 m to 8 m height)
Interception air rod
(8 m to 10 m height)
●
3 piece interception pole
with tripod support frame
●
3 piece interception pole with
‘H’ shaped support frame
●
6 circular concrete bases
●
10 circular concrete bases
Features & benefits
46
●
Protects rooftop mounted equipment from direct
lightning strikes
●
Available in a range of heights from
0.5 m to 10 m
●
Complies with BS EN/IEC 62305 standard
●
●
Lightweight construction
Range of frames and concrete weights for
different wind zones
●
Corrosion resistant
●
Large protection zones
●
Quick and easy to assemble
●
Modular, versatile and robust
Note: installed interception air rods must have sufficient height to provide a clear zone of protection around the
equipment to be protected, as defined by BS EN/IEC 62305-3 (see protective angle method). Further information
can be found in the Furse Guide to BS EN 62305.
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Air termination
S
Product selection
Orkney
Islands
Free standing air rod selection is based on two factors:
a)
air rod height required to create the necessary
protective zone around the equipment
Thurso
Shetland
Islands
Outer
Hebrides
b) anticipated wind loading at the installation
Wind loading is an important factor, especially for
taller interception air rods as extreme weather can
subject them to fatigue mechanisms.
Inverness
Wind zones key:
Aberdeen
Zone 1
O
Windspeed
< 130 km/h
Fort William
For UK installations, the map featured right highlights
four key wind zones from which the appropriate free
standing air rod can be established.
Zone 2
Windspeed < 150 km/h
Dundee
Zone 3
Windspeed < 170 km/h
Glasgow
Relevant part numbers can then be determined
through cross referencing wind loading with the
height of air rod required in the table below.
Edinburgh
Zone 4
Windspeed < 190 km/h
Newcastle
For non-UK installations, please refer to available data
for local wind conditions or contact your Furse
representative to discuss your particular requirements.
For details of individual components, refer to page 41
for copper/aluminium air rods and pages 48-49 for
interception poles, support frames and concrete bases.
UK wind
zone map
York
Leeds
Kingston-upon-Hull
Manchester
Liverpool
Sheffield
Stoke-on-Trent
Norwich
Birmingham
Aberystwyth
Ipswich
Swansea
Newport
Oxford
London
Bristol
Brighton
Z
Plymouth
Rod
height
Frame (where required) and Base Part No. for windspeeds
Interception pole
Part No.
< 130 km/h
< 150 km/h
< 170 km/h
< 190 km/h
0.5 m
RA215 or RA015
103101-FU
103101-FU
103101-FU
103101-FU
1m
RA225 or RA025
103101-FU
103101-FU
103101-FU
103101-FU
1.5 m
RA230 or RA030
103110-FU
103110-FU
103110-FU
103110-FU
2m
RA240 or RA040
103110-FU
103110-FU
103110-FU
103110-FU
3m
912000-FU
499000-FU / 4 x 499100-FU
499000-FU / 4 x 499100-FU
499000-FU / 4 x 499100-FU
499000-FU / 4 x 499100-FU
3.5 m
912001-FU
499000-FU / 4 x 499100-FU
499000-FU / 4 x 499100-FU
499000-FU / 4 x 499101-FU
499000-FU / 4 x 499101-FU
4m
912002-FU
499000-FU / 4 x 499100-FU
499000-FU / 4 x 499101-FU
499000-FU / 8 x 499100-FU
499000-FU / 8 x 499101-FU
4.5 m
912003-FU
499005-FU / 3 x 103101-FU
499005-FU / 3 x 103110-FU
499005-FU / 3 x 103118-FU
499006-FU / 3 x 103103-FU
5m
912004-FU
499005-FU / 3 x 103101-FU
499005-FU / 3 x 103110-FU
499005-FU / 3 x 103118-FU
499006-FU / 3 x 103103-FU
5.5 m
912005-FU
499005-FU / 3 x 103110-FU
499005-FU / 3 x 103118-FU
499006-FU / 6 x 103103-FU
499006-FU / 3 x 103103-FU
6m
912006-FU
499006-FU / 6 x 103103-FU
499006-FU / 6 x 103103-FU
499006-FU / 6 x 103103-FU
499006-FU / 6 x 103101-FU
6.5 m
912007-FU
499006-FU / 6 x 103103-FU
499006-FU / 6 x 103103-FU
499006-FU / 6 x 103101-FU
499006-FU / 6 x 103118-FU
7m
912008-FU
499006-FU / 6 x 103103-FU
499006-FU / 6 x 103101-FU
499006-FU / 6 x 103110-FU
on request
7.5 m
912009-FU
499006-FU / 6 x 103101-FU
499006-FU / 6 x 103110-FU
499006-FU / 6 x 103118-FU
on request
8m
912010-FU
499006-FU / 6 x 103110-FU
499006-FU / 6 x 103118-FU
499007-FU / 10 x 103118-FU
on request
9m
912011-FU
499007-FU / 10 x 103118-FU
499007-FU / 10 x 103118-FU
499007-FU / 10 x 103118-FU
on request
10 m
912013-FU
499007-FU / 10 x 103118-FU
499007-FU / 10 x 103118-FU
on request
on request
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
47
Air termination
Free standing interception pole
912002-FU / 912006-FU / 912010-FU
Pole
Height
Pole
diameter
Pole
make up
Weight
each
Part
No.
3m
10-42 mm
2 pce
5.0 kg
912000-FU
3.5 m
10-42 mm
2 pce
5.5 kg
912001-FU
4m
10-42 mm
2 pce
7.0 kg
912002-FU
4.5 m
10-42 mm
2 pce
9.2 kg
912003-FU
5m
10-42 mm
2 pce
10.0 kg
912004-FU
5.5 m
10-42 mm
2 pce
10.6 kg
912005-FU
6m
10-60 mm
3 pce
18.0 kg
912006-FU
6.5 m
10-60 mm
3 pce
19.0 kg
912007-FU
7m
10-60 mm
3 pce
23.5 kg
912008-FU
7.5 m
10-60 mm
3 pce
26.0 kg
912009-FU
8m
10-60 mm
3 pce
28.7 kg
912010-FU
9m
10-60 mm
3 pce
30.5 kg
912011-FU
10 m
10-60 mm
3 pce
35.5 kg
912013-FU
For construction of interception air rods from 3 to 10 m in height comprising
interception pole, support frame and concrete bases. All interception poles
are grade 304 stainless steel with aluminium interception tip.
Multi-component, stackable system with screw retention. Supplied with
3 terminal lugs for base frame connection.
Base frame
Frame
type
Dimensions
Weight
each
Part
No.
Square base
650 x 650 mm
7 kg
499000-FU
Tripod base
1350 x 1350 mm
8 kg
499005-FU
Tripod base
1850 x 1850 mm
24.5 kg
499006-FU
H shaped base
1850 x 1850 mm
39.5 kg
499007-FU
499000-FU
499006-FU
48
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Air termination
Concrete base
Description
Weight
each
Part
No.
Square concrete base 300 x 300 x 60 mm
12 kg
499100-FU
Square concrete base 300 x 300 x 80 mm
16 kg
499101-FU
Circular concrete base with M16 insert
12 kg
103103-FU
Circular concrete base with M16 insert
16 kg
103101-FU
Circular concrete base with M16 insert
20 kg
103110-FU
Circular concrete base with M16 insert
25 kg
103118-FU
Protective polyethylene tray for circular
concrete blocks
0.4 kg
103102-FU
Stainless steel clamp for connecting 25 x 3 mm
copper tape to 5-19 mm thickness steel
0.55 kg
919828-FU
103103-FU
Accessories
499100-FU
49
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Conductor network
Metallic conductor clips
Non-metallic conductor clips
Standing seam clips
Puddle flange
Holdfasts
Conductor clamps
Test clamps
Bimetallic connectors
Expansion braid bonds
Accessories
51-53
54-59
60
61
61-63
64-67
67-69
70
71
72-74
Conductor network
Swing lid DC tape clip
Conductor
size
Weight
each
Part
No.
25 x 3 mm
0.07 kg
CP210-H†
25 x 6 mm
0.08 kg
CP220-H†
25 x 3 mm
0.03 kg
CP110-H
25 x 6 mm
0.04 kg
CP120-H
For use with bare copper
For use with bare aluminium
CP210-H
DC tape clips manufactured from high quality copper and aluminium alloys
for excellent corrosion resistance and high pull off loads.
IEC/BS EN 62561-4 (CP210-H, CP110-H)
†
UL96 (CP210-H, CP220-H)
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005 or SW105) and wall plugs (Part no. PS305) - see Accessories
page 72.
Adjustable DC tape clip
Conductor
size
Weight
each
Part
No.
31 x 3 mm and 31 x 6 mm
0.12 kg
CP230-H
38 x 3 mm, 38 x 6 mm and 40 x 6 mm
0.14 kg
CP240-H
50 x 3 mm and 50 x 6 mm
0.16 kg
CP260-H†
For use with bare copper
CP260-H
DC tape clips manufactured from high quality copper alloy for excellent
corrosion resistance and high pull off loads. Variable thicknesses of
conductor are accommodated by a reversible lid.
†
UL96 (CP260-H)
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005 or SW105) and wall plugs (Part no. PS305) - see Accessories
page 72.
51
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
DC tape clip
Conductor
size
Weight
each
Part
No.
20 x 3 mm
0.06 kg
CP205
25 x 4 mm
0.07 kg
CP216
30 x 5 mm
0.10 kg
CP227
38 x 5 mm
0.12 kg
CP245
40 x 4 mm
0.14 kg
CP241
50 x 4 mm
0.15 kg
CP256
25 x 3 mm
0.10 kg
CP215
25 x 6 mm
0.13 kg
CP225
50 x 6 mm
0.26 kg
CP265
0.20 kg
CP305
For use with bare copper
CP205
For use with PVC covered copper
For use with lead covered copper
25 x 3 mm
For use with bare aluminium
20 x 3 mm
0.02 kg
CP105
50 x 6 mm
0.05 kg
CP125
25 x 3 mm
0.04 kg
CP115
50 x 6 mm
0.06 kg
CP130
For use with PVC covered aluminium
Manufactured from high quality copper or aluminium alloys.
IEC/BS EN 62561-4 (CP215, CP115)
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005 or SW105) and wall plugs (Part no. PS305) - see Accessories
page 72.
Tape clip
Conductor
size
Weight
each
Part
No.
20 x 3 mm
0.02 kg
CP510
25 x 3 mm
0.02 kg
CP515
20 x 3 mm
0.01 kg
CP405
25 x 3 mm
0.01 kg
CP410
25 x 6 mm
0.01 kg
CP415
0.02 kg
CP517
For use with bare copper
For use with bare aluminium
CP515
NEW
For use with PVC covered tape
25 x 3 mm
Manufactured from pure copper or aluminium, these pressed clips are
available in a range of sizes to suit bare and PVC covered copper and
aluminium tapes.
52
Fix using roundhead wood screws 11⁄2” No. 10 or M6 (Part no.
SW305 or SW405 and wall plugs (Part no. PS305) - see Accessories
page 72.
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
One hole cable clip
Conductor
diameter
Conductor
material
Weight
each
Part
No.
For use with solid circular conductor
8 mm
Copper
0.01 kg
CP905
8 mm
Aluminium
0.01 kg
CP925
10 mm*
Copper
0.01 kg
CP915
10 mm*
Aluminium
0.01 kg
CP935
50 mm2
Copper
0.01 kg
CP910
70 mm2
Copper
0.01 kg
CP915
95 mm2
Copper
0.01 kg
CP920
CP915
For use with stranded conductor
* PVC covered 8 mm conductor.
Manufactured from pure copper or aluminium, these pressed clips are
available to suit bare and PVC covered copper and aluminium solid circular
conductor, and bare copper stranded conductor.
Fix using roundhead wood screws 11⁄2” No. 10 or M6 (Part no.
SW305 or SW405) and wall plugs (Part no. PS305) - see Accessories
page 72.
Heavy duty cast cable saddle
Conductor
diameter
Conductor
material
Weight
each
Part
No.
For use with solid circular conductor
8 mm
Copper
0.09 kg
CP805
8 mm
Aluminium
0.03 kg
CP806
10 mm*
Copper
0.10 kg
CP815
10 mm*
Aluminium
0.04 kg
CP816
CP815
For use with stranded conductor
50 mm2
Copper
0.10 kg
CP810
mm2
Copper
0.10 kg
CP815
95 mm2
Copper
0.10 kg
CP835
70
* For use with PVC covered 8 mm conductor or for supporting air terminals when used in conjunction with
wall mounted air rod bases. Can also be used with glazing bar holdfast and back plate holdfast stem
(see page 63).
Manufactured from high quality copper and aluminium alloys for excellent
corrosion resistance and high pull off loads.
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005 or SW105) and wall plugs (Part no. PS305) - see Accessories
page 72.
53
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Non-metallic DC tape clip
Conductor
size
Colour
Weight
each
Part
No.
20 x 3 mm
Brown
0.01 kg
CP005
20 x 3 mm
Grey
0.01 kg
CP010
25 x 3 mm
Brown
0.01 kg
CP015
25 x 3 mm
Grey
0.01 kg
CP020
38 x 5 mm
Brown
0.01 kg
CP060*
50 x 6 mm
Brown
0.02 kg
CP065*
Brown
0.01 kg
CP025
25 x 3 mm
Black
0.01 kg
CP030
25 x 3 mm
Green
0.01 kg
CP035
25 x 3 mm
Grey
0.01 kg
CP040
25 x 3 mm
Stone
0.01 kg
CP045
25 x 3 mm
White
0.01 kg
CP050
For use with bare tape
CP020
For use with PVC covered tape
25 x 3 mm
* Not as illustrated (drawing available on request).
High grade Polypropylene, UV stabilized against degradation by sunlight
and non-brittle to prevent cold weather damage. Available in six colours to
match bare and PVC covered copper and aluminium tapes.
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005 or SW105) and wall plugs (Part no. PS305) - see Accessories
page 72.
Non-metallic push-in clip
Conductor
diameter
Colour
Weight
each
Part
No.
For use with bare solid circular conductor
8 mm
Brown
0.01 kg
CP887
8 mm
Grey
0.01 kg
CP872
For use with PVC covered solid circular conductor
CP872
10 mm*
Brown
0.01 kg
CP886
10 mm*
Black
0.01 kg
CP861
mm*
Grey
0.01 kg
CP871
10 mm*
Stone
0.01 kg
CP876
mm*
White
0.01 kg
CP881
10
10
* PVC covered 8 mm conductor.
High grade Polypropylene, UV stabilized against degradation by sunlight and
non-brittle to prevent cold weather damage. Available in five colours to
match bare and PVC covered copper and aluminium solid circular conductors.
54
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005 or SW105) and wall plugs (Part no. PS305) - see Accessories
page 72.
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Glue down DC tape clip
Conductor
size
Colour
Weight
each
Part
No.
25 x 3 mm
Brown
0.03 kg
GD015
25 x 3 mm
Grey
0.03 kg
GD020
25 x 3 mm
Brown
0.03 kg
GD025
25 x 3 mm
Black
0.03 kg
GD030
25 x 3 mm
Grey
0.03 kg
GD040
25 x 3 mm
Stone
0.03 kg
GD045
25 x 3 mm
White
0.03 kg
GD050
For use with bare tape
For use with PVC covered tape
GD020
Disc diameter 85 mm.
Use on clay roof tiles. Supplied in a box of 50 complete with adhesive.
Additional glue gun is required.
For dressing tool, see page 59.
Glue down push-in clip
Conductor
diameter
Colour
Weight
each
Part
No.
For use with bare solid circular conductor
8 mm
Brown
0.03 kg
GD887
8 mm
Grey
0.03 kg
GD872
For use with PVC covered solid circular conductor
10 mm*
Brown
0.03 kg
GD886
10 mm*
Black
0.03 kg
GD861
10 mm*
Grey
0.03 kg
GD871
10 mm*
Stone
0.03 kg
GD876
10 mm*
White
0.03 kg
GD881
GD872
* PVC covered 8 mm conductor.
Disc diameter 85 mm.
Use on clay roof tiles. Supplied in a box of 50 complete with adhesive.
Additional glue gun is required.
55
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Self adhesive DC tape clip
Conductor
size
Colour
Weight
each
Part
No.
25 x 3 mm
Brown
0.03 kg
CA015-FU
25 x 3 mm
Grey
0.03 kg
CA020-FU
25 x 3 mm
Brown
0.03 kg
CA025-FU
25 x 3 mm
Black
0.03 kg
CA030-FU
25 x 3 mm
Grey
0.03 kg
CA040-FU
25 x 3 mm
Stone
0.03 kg
CA045-FU
25 x 3 mm
White
0.03 kg
CA050-FU
For use with bare tape
For use with PVC covered tape
CA020-FU
Disc diameter 64 mm.
Designed to secure conductors to surfaces that cannot be penetrated by a
screw. Ideal for aluminium, spangled galvanized steel, colour coated steel,
glass, perspex, enamel and stainless steel etc. Manufactured from high
grade plastic, UV stabilized against degradation by sunlight and non-brittle
to prevent cold weather damage.
For dressing tool and surface primer, see page 59.
Use on surfaces other than PVC roofing.
Self adhesive push-in clip
Conductor
diameter
Colour
Weight
each
Part
No.
For use with bare solid circular conductor
8 mm
Brown
0.02 kg
CA887
8 mm
Grey
0.02 kg
CA872
For use with PVC covered solid circular conductor
CA872
10 mm*
Brown
0.02 kg
CA886
mm*
Black
0.02 kg
CA861
10 mm*
Grey
0.02 kg
CA871
10 mm*
Stone
0.02 kg
CA876
10 mm*
White
0.02 kg
CA881
10
* PVC covered 8 mm conductor.
Disc diameter 64 mm.
Designed as a means of securing conductors to surfaces that cannot be
penetrated by a screw. Ideal for aluminium, spangled galvanized steel,
colour coated steel, glass, perspex, enamel and stainless steel. Manufactured
from high grade plastic, UV stabilized against degradation by sunlight and
non-brittle to prevent cold weather damage.
For surface primer, see page 59.
56
Use on surfaces other than PVC roofing.
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Solvent weldable DC tape clip
Conductor
size
Colour
Weight
each
Part
No.
25 x 3 mm
Brown
0.03 kg
CW015-FU
25 x 3 mm
Grey
0.03 kg
CW020-FU
25 x 3 mm
Brown
0.03 kg
CW025-FU
25 x 3 mm
Black
0.03 kg
CW030-FU
25 x 3 mm
Grey
0.03 kg
CW040-FU
25 x 3 mm
Stone
0.03 kg
CW045-FU
25 x 3 mm
White
0.03 kg
CW050-FU
For use with bare tape
For use with PVC covered tape
CW020-FU
Disc diameter 64 mm.
Provides a secure means of fixing conductors to single ply PVC roof
membranes. Manufactured from high grade PVC, UV stabilized against
degradation by sunlight and non-brittle to prevent cold weather damage.
For dressing tool and welding solvent, see page 59.
Clips are available for Polypropylene, Polyethylene and other roof
membranes - see page 58.
Solvent weldable push-in clip
Conductor
diameter
Colour
Weight
each
Part
No.
For use with bare solid circular conductor
8 mm
Brown
0.03 kg
CW887
8 mm
Grey
0.03 kg
CW872
For use with PVC covered solid circular conductor
10 mm*
Brown
0.03 kg
CW886
10 mm*
Grey
0.03 kg
CW871
CW872
* PVC covered 8 mm conductor.
Disc diameter 64 mm.
Provides a secure means of fixing conductors to single ply PVC roof
membranes. Manufactured from high grade PVC, UV stabilized against
degradation by sunlight and non-brittle to prevent cold weather damage.
For welding solvent, see page 59.
Clips are available for Polypropylene, Polyethylene and other roof
membranes - see page 58.
57
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Heat weldable DC tape clip
NEW
Conductor
size
Colour
Weight
each
Part
No.
25 x 3 mm
Brown
0.03 kg
HW015-FU
25 x 3 mm
Grey
0.03 kg
HW020-FU
25 x 3 mm
Brown
0.03 kg
HW025-FU
25 x 3 mm
Black
0.03 kg
HW030-FU
25 x 3 mm
Grey
0.03 kg
HW040-FU
25 x 3 mm
Stone
0.03 kg
HW045-FU
25 x 3 mm
White
0.03 kg
HW050-FU
For use with bare tape
For use with PVC covered tape
HW020-FU
Disc diameter 85 mm.
Provides a secure means of fixing flat tape conductors to single ply
polypropylene, polyethylene and PVC roof membranes using an industrial
heat gun, where solvent welding is not applicable.
Manufactured from high grade PVC, UV stabilized against degradation by
sunlight and non-brittle to prevent cold weather damage.
For dressing tool, see page 59.
Heat weldable push-in clip
NEW
Conductor
diameter
Colour
Weight
each
Part
No.
For use with bare solid circular conductor
8 mm
Brown
0.03 kg
HW887
8 mm
Grey
0.03 kg
HW872
For use with PVC covered solid circular conductor
HW872
10 mm*
Brown
0.03 kg
HW886
10 mm*
Grey
0.03 kg
HW871
* PVC covered 8 mm conductor.
Disc diameter 85 mm.
Provides a secure means of fixing circular conductors to single ply
polypropylene, polyethylene and PVC roof membranes using an industrial
heat gun, where solvent welding is not applicable.
Manufactured from high grade PVC, UV stabilized against degradation by
sunlight and non-brittle to prevent cold weather damage.
58
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Clip accessories
Description
Weight
each
Part
No.
Universal welding solvent
500 ml spray applicator (sufficient for application of approx
200 clips). Use with Furse solvent weldable clips only.
0.57 kg
CW905
Cleaning solution (Acetone)
500 ml spray applicator. For cleaning lacquered roofing
membranes.
0.62 kg
CW999
Surface primer
250 ml spray applicator (sufficient for application of
approx 500 clips). Use with Furse adhesive clips only.
0.24 kg
CA900
Dressing tool
For use with adhesive and weldable DC tape clips.
0.31 kg
CW905 / CW999 / CA900
DT100
Solvent and surface primer cannot be supplied outside the UK.
For overseas projects, please contact us for advice.
CoSHH Datasheets available on request.
DT100
Bitumen felt roof clip
Conductor
size
Colour
Weight
each
Part
No.
25 x 3 mm
Brown
0.09 kg
FP015
25 x 3 mm
Grey
0.09 kg
FP020
Brown
0.09 kg
FP025
25 x 3 mm
Black
0.09 kg
FP030
25 x 3 mm
Green
0.09 kg
FP035
25 x 3 mm
Grey
0.09 kg
FP040
25 x 3 mm
Stone
0.09 kg
FP045
25 x 3 mm
White
0.09 kg
FP050
For use with bare tape
For use with PVC covered tape
25 x 3 mm
FP020
For dressing tool, see above.
Use on bitumen felt roofing only.
59
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Standing seam roof fixing with non-metallic DC tape clip
NEW
Conductor
size
Conductor
material
Colour
Weight
each
Part
No.
For use with bare tape
25 x 3 mm
Copper
-
0.076 kg
SC015
25 x 3 mm
Aluminium
-
0.076 kg
SC020
For use with PVC covered tape
SC040
25 x 3 mm
Copper/Aluminium
Brown
0.076 kg
SC025
25 x 3 mm
Copper/Aluminium
Black
0.076 kg
SC030
25 x 3 mm
Copper/Aluminium
Green
0.076 kg
SC035
25 x 3 mm
Copper/Aluminium
Grey
0.076 kg
SC040
25 x 3 mm
Copper/Aluminium
Stone
0.076 kg
SC045
25 x 3 mm
Copper/Aluminium
White
0.076 kg
SC050
Highly versatile, innovative standing seam roof fixing including non-metallic
DC tape clip, suitable for use on multi-profiled seam roofing structures up to
22 mm thickness. Use with bare and PVC covered copper and aluminium
conductors. Separate datasheet available on request.
Standing seam roof fixing with square tape clamp
NEW
SC105-H
Conductor
size
Conductor
material
Weight
each
Part
No.
25 x 3 mm
Copper
0.18 kg
SC105-H
25 x 3 mm
Aluminium
0.12 kg
SC005-H
Highly versatile, innovative standing seam roof fixing including square
tape clamp, suitable for use on multi-profiled seam roofing structures up to
22 mm thickness. Use with bare and PVC covered copper and aluminium
conductors. Separate datasheet available on request.
60
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Puddle flange
Conductor
material
Weight
each
Part
No.
Copper
1.54 kg
PF105
Aluminium
0.50 kg
PF005
Permits lightning conductors to pass through flat roofs without damaging
the waterproof nature of the roof.
150 mm
150 mm
450 mm
ø5/8”
PF105
Pyramid holdfast
Conductor
diameter
Weight
each
Part
No.
8 mm
0.97 kg
HF975
Designed to secure bare, 8 mm diameter, circular conductors to flat roofs.
Supplied filled with concrete the conductor is held in place by the weight of
the holdfast.
The lip around the base of the product permits the holdfast to be built into
bitumen type roofs.
HF975
140 mm
140 mm
79 mm
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
61
Conductor network
Slate holdfast with non-metallic DC tape clip
Conductor
size
DC Clip
Colour
Weight
each
Part
No.
25 x 3 mm
Brown
0.06 kg
HF015
25 x 3 mm
Grey
0.06 kg
HF020
25 x 3 mm
Brown
0.06 kg
HF025
25 x 3 mm
Black
0.06 kg
HF030
25 x 3 mm
Grey
0.06 kg
HF040
25 x 3 mm
Stone
0.06 kg
HF045
For use with bare tape
For use with PVC covered tape
HF040
Designed to allow tape conductors to be fixed to tiled roofs without
compromising the waterproofing nature of the roof. The 500 mm tail fits
neatly between overlapping tiles and is wrapped around/fixed to the tile
lathe for secure fitting.
Slate holdfast with non-metallic push-in clip
HF191
Conductor
diameter
Colour
Weight
each
Part
No.
8 mm
Brown
0.03 kg
HF176
8 mm
Grey
0.03 kg
HF191
Designed to allow circular conductors to be fixed to tiled roofs without
compromising the waterproofing nature of the roof. The 500 mm tail fits
neatly between overlapping tiles and is wrapped around/fixed to the tile
lathe for secure fitting.
62
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Glazing bar holdfast
Conductor
material
Maximum glazing
bar width
Weight
each
Part
No.
Copper
12 mm
0.11 kg
HF705
Aluminium
12 mm
0.05 kg
HF710
Manufactured from high quality copper and aluminium alloys. Simple to
install, providing secure anchorage to thin metallic sections that cannot be
drilled e.g. window mullions, angle iron etc. Once fixed any metallic or
non-metallic conductor clip can be attached with the screw provided.
HF705
Conductor clip sold separately.
Back plate holdfast stem
Conductor
material
Weight
each
Part
No.
Copper
0.30 kg
HF320
Aluminium
0.10 kg
HF325-FU
Supplied with M6 fixing screw to secure appropriate conductor clip.
Fix using roundhead wood screws 11⁄2” No. 10 or M6 (Part no.
SW305 or SW405) and wall plugs (Part no. PS305) - see Accessories
page 72.
HF320
63
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Square clamp
NEW
Conductor
size
Conductor
material
Weight
each
Part
No.
25 x 3 mm
Copper
0.12 kg
CT105-H†
25 x 6 mm
Copper
0.30 kg
CT110-H†
50 x 6 mm
Copper
0.60 kg
CT115-H†
25 x 3 mm
Aluminium
0.06 kg
CT005-H
25 x 6 mm
Aluminium
0.17 kg
CT010-H
CT105-H
Manufactured from high quality copper and aluminium alloys. Simple
to install, providing an effective low resistance connection between
overlapping tapes to allow cross, tee, through and right angle joints to
be formed.
BS EN 50164-1 Class H
†
UL96 (CT105H, CT110-H, CT115-H)
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005 or SW105) and wall plugs (Part no. PS305) - see Accessories
page 72.
Tightening torque 5 Nm
Crossover clamp
Conductor
size
CX105-H
Conductor
material
Weight
each
Part
No.
25 x 3 mm
Copper
0.09 kg
CX105-H
25 x 3 mm
Aluminium
0.03 kg
CX005-H
Manufactured from high quality copper and aluminium alloys. Simple to
install, providing an effective low resistance connection between
overlapping tapes to allow cross joints to be formed.
BS EN 50164-1 Class H
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005 or SW105) and wall plugs (Part no. PS305) - see Accessories
page 72.
Tightening torque 5 Nm
64
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Cable to tape square clamp
Conductor
size
Conductor
material
Weight
each
Part
No.
25 x 3 mm to 50 mm²
Copper
0.32 kg
CT125
25 x 3 mm to 70 mm²
Copper
0.30 kg
CT130
25 x 3 mm to 95 mm²
Copper
0.28 kg
CT135
NEW
NEW
Manufactured from high quality copper alloy. Simple to install, providing
an effective low resistance connection between conductor tape and
stranded copper conductor, allowing cross, tee, through and right angle
joints to be formed.
CT130
BS EN 50164-1 Class H
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005) and wall plugs (Part no. PS305) - see Accessories page 72.
Tightening torque 5 Nm
Square clamp
Conductor
diameter
Conductor
material
Weight
each
Part
No.
50 mm2
Copper
0.32 kg
CR810
70 mm2
Copper
0.29 kg
CR815
mm2
Copper
0.25 kg
CR820
95
Manufactured from high quality copper alloy. Simple to install, providing an
effective low resistance connection between overlapping stranded
conductors allowing cross, tee, through and right angle joints to be formed.
CR815
BS EN 50164-1 Class H
Tightening torque 6 Nm
65
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Square clamp
Conductor
diameter
Conductor
material
Weight
each
Part
No.
8 mm
Copper
0.17 kg
CS605
8 mm
Aluminium
0.07 kg
CS610
Designed to provide low resistance cross joints in solid circular conductor
networks. Manufactured from high quality copper and aluminium alloys for
excellent corrosion resistance.
CS605
BS EN 50164-1 Class H
Tightening torque 12 Nm
Tee clamp
Conductor
diameter
Conductor
material
Weight
each
Part
No.
8 mm
Copper
0.17 kg
CS505
8 mm
Aluminium
0.07 kg
CS510
Designed to provide low resistance tee joints in solid circular conductor
networks. Manufactured from high quality copper and aluminium alloys for
excellent corrosion resistance.
CS505
BS EN 50164-1 Class H
Tightening torque 12 Nm
66
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Jointing clamp
Conductor
diameter
Conductor
material
Weight
each
Part
No.
8 mm
Copper
0.17 kg
CS405
8 mm
Aluminium
0.08 kg
CS410
Designed to provide low resistance parallel joints in solid circular conductor
networks. Manufactured from high quality copper and aluminium alloys for
excellent corrosion resistance.
CS405
BS EN 50164-1 Class H
Tightening torque 12 Nm
Test/junction clamp
Conductor
size
Conductor
material
Weight
each
Part
No.
26 x 8 mm
Copper
0.29 kg
CN105-H†
26 x 8 mm
Aluminium
0.12 kg
CN005*
* Not as illustrated (drawing available on request).
Manufactured from high quality copper and aluminium alloys. Simple to
install, providing an effective low resistance connection between
overlapping tapes. The clamped connection is easily made/remade to allow
for periodic testing.
CN105-H
BS EN 50164-1 Class H
†
UL96 (CN105-H)
Tightening torque CN005 15 Nm; CN105-H 13 Nm
67
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Plate type test clamp
Maximum
conductor size
26 x 12 mm
Conductor
material
Weight
each
Part
No.
Copper
0.62 kg
CT405
Manufactured from a high quality copper alloy. Simple to install, providing
an effective low resistance connection between overlapping tapes. The
clamped connection is easily made/remade to allow for periodic testing.
Enables cross, tee, through and right angle joints to be formed.
CT405
BS EN 50164-1 Class H
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005) and wall plugs (Part no. PS305) - see Accessories page 72.
Tightening torque 15 Nm
Screwdown test clamp
Maximum
conductor size
26 x 8 mm
Conductor
material
Weight
each
Part
No.
Copper
0.84 kg
CT305
Manufactured from a high quality copper alloy. Simple to install, providing
an effective low resistance connection between overlapping tapes. The
clamped connection is easily made/remade to allow for periodic testing.
Enables cross, tee, through and right angle joints to be formed.
CT305
BS EN 50164-1 Class H
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005) and wall plugs (Part no. PS305) - see Accessories page 72.
Tightening torque 20 Nm
68
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Test clamp
Conductor
diameter
Conductor
size
Conductor
material
Weight
each
Part
No.
8 mm
25 x 3 mm
Copper
0.20 kg
CN305
8 mm
25 x 3 mm
Aluminium
0.09 kg
CN310
Designed to provide low resistance tee joints in solid circular conductor
networks. These multi-purpose clamps can produce circular to circular or
circular to tape connection in both through and tee configurations.
Manufactured from high quality copper and aluminium alloys for excellent
corrosion resistance.
CN305
BS EN 50164-1 Class H
Tightening torque 12 Nm
Test clamp
Conductor
diameter
Conductor
material
Weight
each
Part
No.
50 mm2
Copper
0.39 kg
CR855
70 mm2
Copper
0.40 kg
CR860
mm2
Copper
0.40 kg
CR865
95
Manufactured from high quality copper alloy. Simple to install, providing an
effective low resistance overlap connection between stranded copper cables.
CR860
BS EN 50164-1 Class H
Fix using countersunk wood screws 11⁄2” No. 10 or M6 (Part no.
SW005) and wall plugs (Part no. PS305) - see Accessories page 72.
Tightening torque 12 Nm
69
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Bimetallic connector
Conductor
size
Weight
each
Part
No.
25 x 3 mm aluminium tape to 25 x 3 mm copper tape
0.19 kg
CN910
1 ⁄2” x ⁄8” aluminium tape to 1” x ⁄8” copper tape
0.19 kg
CN910-UL†
8 mm diameter aluminium conductor to 8 mm diameter
copper conductor
0.25 kg
CN915
8 mm diameter aluminium conductor to 25 x 3 mm
copper tape
0.19 kg
CN920
25 x 3 mm aluminium tape to 25 x 3 mm copper tape
0.20 kg
CN925
1
CN910
1
1
Manufactured from a friction welded joint between high conductivity
copper and aluminium to provide the ideal means of interconnecting copper
and aluminium conductors whilst avoiding bimetallic corrosion.
BS EN 50164-1 Class H
†
UL96 (CN910-UL)
CN915
Fix using countersunk wood screws 11⁄2” No. 10 or M6
(Part no. SW005 or SW105) and wall plugs (Part no. PS305) see Accessories page 72.
Tightening torque 12 Nm
CN925
CN910 illustrated
70
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Conductor network
Oxide inhibiting compound
Description
Weight
each
Part
No.
Plastic 8 oz bottle
0.23 kg
CM005
For all the items in this range we recommend the use of oxide inhibitor
when aluminium fittings are installed.
Oxide inhibitor is a non-water soluble, natural-petroleum based polymer
grease that seals electrical connections from oxygen and moisture.
CoSHH Datasheet available on request.
CM005
Expansion braid bond
Type
Conductor
material
Length
Cross-sectional
area
Weight
each
Part
No.
Single length
Copper
200 mm
50 mm2
0.17 kg
BN101
Single length
Aluminium
200 mm
50 mm2
0.07 kg
BN001
mm2
0.53 kg
BN102
0.23 kg
BN002
Cross-over
Copper
300 mm
50
Cross-over
Aluminium
300 mm
50 mm2
Designed to remove the risk of damage or distortion to long conductor runs
caused by thermal expansion and contraction.
BN102
71
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Accessories
Countersunk wood screws
Countersunk set screws
Size
Weight
per 100
Part
No.
Zinc plated steel
11⁄2” x No.10
0.50 kg
SW105
Zinc plated steel
11⁄2” x No.12
0.60 kg
SW110
Brass
11⁄2” x No.10
0.50 kg
SW005
Brass
11⁄2” x No.12
0.60 kg
SW010
Roundhead wood screws
Brass
Size
Weight
per 100
Part
No.
M6 x 30 mm
0.60 kg
SS160
Hexagon head set screws
Size
Weight
per 100
Part
No.
Zinc plated steel
11⁄2” x No.10
0.50 kg
SW405
Brass
11⁄2” x No.10
0.50 kg
SW305
Plastic wall plugs
Size
Weight
per 100
Part
No.
Phosphor bronze
M10 x 25 mm
2.85 kg
SS635
Phosphor bronze
M10 x 35 mm
3.40 kg
SS640
Phosphor bronze
M12 x 25 mm
4.50 kg
SS650
Phosphor bronze
M12 x 35 mm
5.00 kg
SS655
Brass
M8 x 16 mm
1.75 kg
SS165
Brass
M10 x 25 mm
2.50 kg
SS140
Brass
M10 x 35 mm
3.20 kg
SS145
Brass
M12 x 25 mm
3.80 kg
SS150
Brass
M12 x 35 mm
4.70 kg
SS155
Size
Weight
per 100
Part
No.
Hexagon nuts
Size
Weight
per 100
Part
No.
Red
No.10
0.06 kg
PS305
Phosphor bronze
M10
1.25 kg
NU367
Brown
No.12
0.06 kg
PS310
Phosphor bronze
M12
1.80 kg
NU370
Brass
M6
0.25 kg
NU165
Brass
M8
0.80 kg
NU166
Brass
M10
1.15 kg
NU167
Brass
M12
1.65 kg
NU170
72
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Accessories
Roundhead rivets
Size
Weight
per 100
Part
No.
Copper
5 x 12 mm
0.35 kg
RV105
Copper
5 x 20 mm
0.45 kg
Aluminium
5 x 12 mm
0.12 kg
Aluminium
5 x 20 mm
0.15 kg
RV010
Spring washers
Size
Weight
per 100
Part
No.
Phosphor bronze
6 mm
0.04 kg
WS365
RV110
Phosphor bronze
10 mm
0.20 kg
WS367
RV005
Phosphor bronze
12 mm
0.20 kg
WS370
Masonry drills
Roundhead copper nails
Size
Weight
each
Part
No.
Size
Weight
per 100
Part
No.
No.10
0.02 kg
DL005
50 mm long
0.70 kg
NA005
No.12
0.02 kg
DL010
Plain washers
Insulating tape
Size
Weight
per 100
Part
No.
Coil
size
Weight
each
Part
No.
Phosphor bronze
6 mm
0.05 kg
WR365
25 mm x 33 m
0.14 kg
TP120-FU
Phosphor bronze
10 mm
0.25 kg
WR367
Phosphor bronze
12 mm
0.50 kg
WR370
Brass
6 mm
0.05 kg
WR165
Brass
8 mm
0.15 kg
WR175
Brass
10 mm
0.25 kg
WR167
Brass
12 mm
0.50 kg
WR170
Green/yellow general purpose insulating tape.
73
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Accessories
Denso tape
Tinmans solder
Coil
size
Weight
each
Part
No.
Material
Weight
each
Part
No.
50 mm x 10 m
0.76 kg
TD005
60% tin, 40% lead
0.26 kg
SA105
A waterproof tape for wrapping underground joints.
CoSHH Datasheet available on request.
Flux
Silfos
Coil
size
50 mm x 8 m
Thickness
Weight
each
Part
No.
Material
Weight
each
Part
No.
0.12 mm
0.50 kg
FS005
Flux
0.08 kg
SA115
An alloy of silver, phosphorous and copper. Used to
braze copper in air without the use of Flux.
Use with tinmans solder for general purpose soldering
of copper products.
CoSHH Datasheet available on request.
CoSHH Datasheet available on request.
74
Furse, Wilford Road, Nottingham, NG2 1EB • Tel: +44 (0)115 964 3700 • Email: [email protected] • Web: www.furse.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement