Analog Devices Welcomes Hittite Microwave Corporation www.analog.com www.hittite.com

Analog Devices Welcomes Hittite Microwave Corporation www.analog.com www.hittite.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC675LC3C
v10.0514
COMPARATORS - SMT
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
Typical Applications
Features
The HMC675LC3C is ideal for:
Equivalent Input Bandwidth: 10 GHz
• ATE Applications
Propagation Delay: 100 ps
• High Speed Instrumentation
Overdrive & Slew Rate Dispersion: 10 ps
• Digital Receiver Systems
Minimum Pulse Width: 60 ps
• Pulse Spectroscopy
Resistor Programmable Hysteresis
• High Speed Trigger Circuits
Differential Latch Control
• Clock & Data Restoration
Power Dissipation: 100 mW
RSPECL and RSECL Versions Available
16 Lead 3x3 mm SMT Package: 9 mm 2
Functional Diagram
General Description
The HMC675LC3C is a SiGe monolithic, ultra fast
comparator that features reduced swing (RS) CML
output drivers and latch inputs. The comparator
supports 10 Gbps operation while providing 100 ps
propagation delay and 60 ps minimum pulse width with
0.2 ps rms random jitter (RJ). Overdrive and slew rate
dispersion are typically 10 ps, making the device ideal
for a wide range of applications from ATE to broadband
communications. The reduced swing CML output stage
is designed to directly drive 400 mV into 50 ohms
terminated to GND. The HMC675LC3C features high
speed latch and programmable hysteresis and may
be configured to operate in either latch mode, or as a
tracking comparator.
Electrical Specifications
TA = +25 ºC, Vcci= +3.3 V, Vcco = 0 V, Vee = -3 V, VTERM = 0
Parameter
Conditions
Input Voltage Range
Input Differential Voltage
Max
Units
-2
Typ.
2
V
-1.75
1.75
V
Input Offset Voltage
±5
mV
Input Offset Voltage, Temperature Coefficient
15
µV / °C
Input Bias Current
15
uA
Input Bias Current Temperature Coefficient
50
nA / °C
µA
Input Offset Current
4
Input Impedance
50
Ω
Common Mode Input Impedance
350
KΩ
Differential Input Impedance
15
KΩ
Active Gain
43
dB
Common Mode Rejection Ratio
80
dB
±1
mV
Hysteresis
1
Min.
Rhys = ∞
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC675LC3C
v10.0514
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
Latch Enable Characteristics
Conditions
Min.
Typ.
Max
Units
Each Pin
8
KΩ
Latch Enable to Output Delay, tPLOL , tPLOH
VOD = 200 mV
85
ps
Latch Enable Minimum Pulse Width, tPL
VOD = 200 mV
20
Latch Enable Input Range
VOD = 200 mV
Latch Setup Time, tS
VOD = 200 mV
1.6
Latch Hold Time, tH
ps
2.4
V
45
ps
-42
ps
DC Output Characteristics, with 50 Ω to GND
Parameter
Conditions
Min.
Max
Units
0
mV
-400
-380
mV
410
400
380
mV
Conditions
Min.
Typ.
Max
Units
VOD = 500 mV
70
100
130
Output Voltage High Level, Voh
-10
Output Voltage Low Level, Vol
-420
Output Voltage Differential Swing
Typ.
AC Performance
Parameter
Propagation Delay - tPD, tPDL , tPDH
Propagation Delay, Temperature Coefficient
Propagation Delay Skew
(Rising to Falling Transition)
VOD Dispersion
TPD vs. Common Mode Dispersion,
-1.75V <Vcm <1.75V
ps / °C
VOD - 500 mV
10
ps
50mV < VOD < 1V
10
ps
VOD = 500 mV
3
ps
3.2
Equivalent Input Bandwidth [1]
Deterministic Jitter (pp)
ps
0.45
Noise (RTI)
8.5
10
nV/√(Hz) RTI
10.5
GHz
Deterministic Jitter at 10 Gbps
with ±100mV Overdrive
2
ps
Random Jitter at 10 Gbps
with ±100mV Overdrive
0.2
ps rms
Random Jitter (rms)
Input Signal Minimum Pulse Width
COMPARATORS - SMT
Parameter
Latch Enable Input Impedance
60
ps
Q / QB Rise Time
From 20% to 80%
27
ps
Q / QB Fall Time
From 20% to 80%
18
ps
Power Supply Requirements
Parameter
Conditions
Min.
Typ.
Max
Units
Input Supply Current, Icci
9
mA
Output Supply Current, Icco
8
mA
Vee Current, lee
24
mA
Power Dissipation, Pd
100
mW
PSRR, Vcci
35
dB
PSRR, Vee
35
dB
Note 1: Equivalent Input Bandwidth is calculated with the following formula: Bweq=0.22/√ (TRCOMP2 -TRIN 2) where TRIN is the 20%/80%
transition time of a quasi-Gaussian signal applied to the comparator input, and TRCOMP is the effective transition time digitized by the
comparator.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
2
HMC675LC3C
v10.0514
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
Dispersion vs. Overdrive Voltage
Propagation Delay vs. Common Mode[1]
15
12.5
9
10
7
tPD
DISPERSION (ps)
COMPARATORS - SMT
11
5
7.5
5
2.5
3
0
1
-2.5
-5
-1
0
10
20
30
40
50
60
70
80
90
100
-2
-1.5
-1
-0.5
0
0.5
1
1.5
2
COMMON MODE VOLTAGE (mV)
OVERDRIVE VOLTAGE (mV)
Rising Edge
Falling Edge
Rising Edge
Falling Edge
Comparator Hysteresis
vs. Rhys Control Resistor
Output Voltage vs. Temperature
15
0.1
0
HYSTERESIS (mV)
VOLTAGE (V)
-0.1
-0.2
-0.3
-0.4
10
5
-0.5
-0.6
-45
0
-32
-19
-6
7
20
33
46
59
72
85
TEMPERATURE (C)
100
1000
10000
RESISTANCE (Ohm)
VOH
VOL
Eye Diagram
[1] Vcci = 3.3 V, Vcc0 = 0, Vee = -3 V, VTERM = 0
3
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC675LC3C
v10.0514
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
COMPARATORS - SMT
Timing Diagram
Symbol
Timing
Description
tPDH
Input to output high delay
Propagation delay measured from the time the input signal crosses the reference
(± the input offset voltage) to the 50% point of an output low-to-high transition.
tPDL
Input to output low delay
Propagation delay measured from the time the input signal crosses the reference
(± the input offset voltage) to the 50% point of an output high-to-low transition.
tPLOH
Latch enable to output high delay
Propagation delay measured from the 50% point of the latch enable signal high-to-low
transition to the 50% point of an output low-to-high transition.
tPLOL
Latch enable to output low delay
Propagation delay measured from the 50% point of the latch enable signal high-to-low
transition to the 50% point of an output high-to-low transition.
tH
Minimum hold time
Minimum time after the positive transition of the latch enable signal that the input signal
must remain unchanged to be acquired and held at the outputs.
tPL
Minimum latch enable pulse width
Minimum time that the latch enable signal must be low to acquire an input signal
change.
tS
Minimum setup time
Minimum time before the positive transition of the latch enable signal that an input
signal change must be present to be acquired and held at the outputs.
tR
Output rise time
Amount of time required to transition from a low to a high output as measured at the
20% and 80% points.
tF
Output fall time
Amount of time required to transition from a high to a low output as measured at the
20% and 80% points.
Voltage overdrive
Difference between the input voltages VINP and VINN-
VOD
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
4
HMC675LC3C
v10.0514
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
COMPARATORS - SMT
Operational Description
5
The HMC675LC3C is a Latched Comparator with 10 GHz equivalent input bandwidth. The device is comprised of three
blocks: 1) An input amplifier, 2) A latch, and 3) An RSCML Output Buffer. The latching circuit is level sensitive, and
consists of a single high-speed latch. The HMC675LC3C comparator supports 10 Gb/s operation. The minimum input
data latching pulse width is 60 ps.
The HMC675LC3C operates in either Track (Transparent) Mode, where the output follows the logical value of the input,
or the Latch (Hold) Mode, where the output value is held to the logical value of the comparison result of the input just prior
to (LE - LE_bar) going HI. Track Mode operation is selected by either 1) (LE - LE_bar) LO, or 2) LE and LE_bar inputs
floating. Latch Mode is selected by (LE - LE_bar) HI. The input impedance of the LE and LE_bar inputs is 8 k ohms, but
these inputs can be terminated with 50 ohm external resistors if desired.
When DC coupled, the clock inputs operate at an input common mode voltage of 2 V. In this case, any termination
resistors would ideally be returned to 2 V. If the clock is AC coupled to the device, the input termination resistors can be
returned to ground.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC675LC3C
v10.0514
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
Input Supply Voltage (Vcci to GND)
-0.5 V to +4 V
Output Supply Voltage (Vcco to GND)
-0.5 V to +4 V
Positive Supply Voltage Differential
(Vcci - Vcco)
-0.5 V to +3.3 V
Input Voltage
-2 V to +2 V
Differential Input Voltage
-2 V to +2 V
Input Voltage, Latch Enable
-0.5 V to Vcci +0.5 V
Applied Voltage (HYS)
Vee to GND
Maximum Input Current
±20 mA
Output Current
20 mA
Junction Temperature
125 °C
Continuous Pdiss (T = 85 °C)
(Derate 20.4 mW/°C above 85 °C)
0.816 W
Thermal Resistance (Rth) (Junction to Lead)
49 °C/W
Storage Temperature
-65 °C to +150 °C
Operating Temperature
-40 °C to +85 °C
ESD Sensitivity (HBM)
Class 1A
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
COMPARATORS - SMT
Absolute Maximum Ratings
Outline Drawing
NOTES:
1. PACKAGE BODY MATERIAL: ALUMINA
2. LEAD AND GROUND PADDLE PLATING:
30-80 MICROINCHES GOLD OVER 50 MICROINCHES MINIMUM NICKEL.
3. DIMENSIONS ARE IN INCHES [MILLIMETERS].
4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm DATUM -C6. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND.
7. PADDLE MUST BE SOLDERED TO Vee.
Package Information
Part Number
Package Body Material
Lead Finish
HMC675LC3C
Alumina, White
Gold over Nickel
MSL Rating
MSL3
[1]
Package Marking [2]
H675
XXXX
[1] Max peak reflow temperature of 260 °C
[2] 4-Digit lot number XXXX
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
6
HMC675LC3C
v10.0514
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
COMPARATORS - SMT
Pin Descriptions
Pin Number
Function
Description
1
VTP
Termination resistor return pin for Vp Input.
2
INP
Non-Inverting analog input
3
INN
Inverting analog input
4
VTN
Termination resistor return pin for Vn input
5, 16
Vcci
Positive supply voltage input stage.
6
LE
Latch enable bar input pin, inverting side.
Refer to the Operational Description for more details.
7
LE
Latch enable input pin, non-inverting side.
Refer to the Operational Description for more details
8
N/C
Pin is not connected inside the package.
Connect package pin to GND for improved noise.
9, 12
Vcco
Positive supply voltage for the output stage.
Q
Inverting output. Q bar is at logic low if the analog voltage
at the non-inverting input, INP, is greater than the analog
voltage at the inverting input, INN, provided that the
comparator is in compare mode. Refer to the Operational
Description for more details
Q
Non-inverting output. Q is at logic high if the analog voltage
at the non-inverting input, INP, is greater than the analog
voltage at the inverting input, INN, provided that the
comparator is in compare mode. Refer to the Operational
Description for more details
14
HYS
Hysteresis Control pin. This pin should be left disconnected
for zero hysteresis. Connect to Vee with a resistor to add
the desired amount of hysteresis. Refer to hysteresis graph
to determine the correct sizing of Rhys control resistor.
13
Vee
Negative power supply, -3V.
15
RTN
Return for ESD protection.
Package Base
Exposed paddle must be connected to Vee.
10
11
7
Interface Schematic
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC675LC3C
v10.0514
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
Evaluation PCB
COMPARATORS - SMT
Front Side
Back Side
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8
HMC675LC3C
v10.0514
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
COMPARATORS - SMT
List of Materials for Evaluation PCB 125932 [1]
Item
Description
J1
8 Pos. Vertical TIN
J2 - J7
2.92 mm 40 GHz Jack
J8
Terminal Strip, Single Row 3 Pin SMT
JP1, JP2
2 Pos. Vertical TIN
C1 - C3, C5, C6,
C8 - C10
100 pF Capacitor, 0402 Pkg.
C4, C7, C11
330 pF Capacitor, 0402 Pkg.
C11 - C13
4.7 uF Tantalum
TP1 - TP4
DC Pin, Swage Mount
U1
HMC675LC3C Comparator
PCB
125929 Evaluation PCB
The circuit board used in the application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package ground leads should be connected directly to
the ground plane similar to that shown. A sufficient
number of via holes should be used to connect the
top and bottom ground planes in order to provide
good RF grounding to 25 GHz. The evaluation
circuit board shown is available from Hittite upon
request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350 or Arlon 25FR
Application Circuit
9
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC675LC3C
v10.0514
10 GHz LATCHED COMPARATOR
WITH RSCML OUTPUT STAGE
COMPARATORS - SMT
Notes:
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement