3M Spray Mount Adhesive

3M Spray Mount Adhesive
MATERIAL SAFETY DATA SHEET 3M(TM) Spray-Mount(TM) Artist's Adhesive 6064, 6065
09/16/2008
Material Safety Data Sheet
Copyright, 2008, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) Spray-Mount(TM) Artist's Adhesive 6064, 6065
MANUFACTURER: 3M
DIVISION: Stationery Products
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 09/16/2008
Supercedes Date: 02/08/2008
Document Group: 22-0411-3
Product Use:
Intended Use:
Adhesive
SECTION 2: INGREDIENTS
Ingredient
C.A.S. No.
ACETONE
HEPTANE ISOMERS
ISOBUTANE
NON-VOLATILE COMPONENTS - N.J. TRADE SECRET REGISTRY NO.
04499600-6201P++
PROPANE
67-64-1
64742-49-0
75-28-5
Trade Secret
% by Wt
30 - 40
20 - 30
20 - 30
7 - 13
74-98-6
7 - 13
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Specific Physical Form: Aerosol
Odor, Color, Grade: Mild Solvent Odor/Clear-light yellow
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: Aerosol container contains flammable gas under pressure. Closed
containers exposed to heat from fire may build pressure and explode. Extremely flammable liquid and vapor. Vapors may travel long
distances along the ground or floor to an ignition source and flash back. Aerosol container contains flammable material under
pressure.
May cause target organ effects.
_________________________________________________________________________________________________
Page 1 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Spray-Mount(TM) Artist's Adhesive 6064, 6065
09/16/2008
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Inhalation:
Intentional concentration and inhalation may be harmful or fatal.
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air.
If signs/symptoms develop, get medical attention.
If Swallowed:
Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature
No Data Available
_________________________________________________________________________________________________
Page 2 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Spray-Mount(TM) Artist's Adhesive 6064, 6065
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
09/16/2008
-50.00 ºF [Test Method: Tagliabue Closed Cup] [Details:
CONDITIONS: Propellant]
Approximately 1.85 % volume
Approximately 9.9 % volume
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed
containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained
breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Closed containers exposed to heat from fire may build pressure and explode. Extremely
flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and flash back. Aerosol
container contains flammable material under pressure.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Refer to other sections of this MSDS for information regarding physical and health hazards,
respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information
on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up
by qualified personnel. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only nonsparking tools. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to
disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and
could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains and build
dikes to prevent entry into sewer systems or bodies of water. Cover spill area with a fire-extinguishing foam. An aqueous film
forming foam (AFFF) is recommended. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or
commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an
absorbent material does not remove a toxic, corrosivity or flammability hazard. Collect as much of the spilled material as possible
using non-sparking tools. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the
area with fresh air. Read and follow safety precautions on the solvent label and MSDS. Collect the resulting residue containing
solution. Place in a metal container approved for transportation by appropriate authorities. Seal the container. Dispose of collected
material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep away from heat,
sparks, open flame, pilot lights and other sources of ignition. Do not pierce or burn container, even after use. No smoking while
handling this material. Do not spray near flames or sources of ignition. Avoid breathing of vapors, mists or spray. Aerosol container
contains flammable gas under pressure. Avoid static discharge. Avoid eye contact with vapors, mists, or spray. Keep out of the reach
of children. Avoid contact with oxidizing agents.
_________________________________________________________________________________________________
Page 3 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Spray-Mount(TM) Artist's Adhesive 6064, 6065
09/16/2008
7.2 STORAGE
Store away from acids. Store away from heat. Store out of direct sunlight. Keep container tightly closed. Do not store containers on
their sides. Store away from oxidizing agents.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Do not use in a confined area or areas with little or no air movement. Use general dilution ventilation and/or local exhaust ventilation
to control airborne exposures to below Occupational Exposure Limits and/or control mist, vapor, or spray. If ventilation is not
adequate, use respiratory protection equipment.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure
assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Polyvinyl Alcohol (PVA), Polyethylene/Ethylene Vinyl Alcohol.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges, Half facepiece or fullface
pressure demand self-contained breathing apparatus. Consult the current 3M Respiratory Selection Guide for additional information
or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient
ACETONE
ACETONE
ACETONE
ACETONE
ACETONE
HEPTANE ISOMERS
ISOBUTANE
PROPANE
PROPANE
Authority
Type
Limit
Additional Information
ACGIH
ACGIH
OSHA
OSHA
OSHA
CMRG
ACGIH
ACGIH
OSHA
TWA
STEL
TWA, Vacated
TWA
STEL, Vacated
TWA
TWA
TWA
TWA
500 ppm
750 ppm
750 ppm
1000 ppm
1000 ppm
50 ppm
1000 ppm
1000 ppm
1000 ppm
Table A4
Table A4
Table Z-1
Table Z-1
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
_________________________________________________________________________________________________
Page 4 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Spray-Mount(TM) Artist's Adhesive 6064, 6065
09/16/2008
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Flammable Limits - LEL
Flammable Limits - UEL
Boiling point
Density
Vapor Density
Aerosol
Mild Solvent Odor/Clear-light yellow
Liquid
No Data Available
-50.00 ºF [Test Method: Tagliabue Closed Cup] [Details:
CONDITIONS: Propellant]
Approximately 1.85 % volume
Approximately 9.9 % volume
Not Applicable
0.673 g/ml
No Data Available
Specific Gravity
pH
Melting point
0.673 [Ref Std: WATER=1]
Not Applicable
Not Applicable
Solubility in Water
Evaporation rate
Hazardous Air Pollutants
Volatile Organic Compounds
Percent volatile
VOC Less H2O & Exempt Solvents
Negligible
No Data Available
0 % weight [Test Method: Calculated]
Approximately 58 % weight
Approximately 91 % weight
Approximately 538 g/l [Test Method: calculated SCAQMD rule
443.1]
Not Applicable
Specific Physical Form:
Odor, Color, Grade:
General Physical Form:
Autoignition temperature
Flash Point
Viscosity
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Heat; Sparks and/or flames
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance
Condition
Aldehydes
Carbon monoxide
Carbon dioxide
During Combustion
During Combustion
During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
_________________________________________________________________________________________________
Page 5 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Spray-Mount(TM) Artist's Adhesive 6064, 6065
09/16/2008
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in a permitted hazardous waste incinerator. As a disposal alternative, dispose of waste product
in a permitted hazardous waste facility.
Facility must be capable of handling aerosol cans. Dispose of empty product containers in a sanitary landfill.
EPA Hazardous Waste Number (RCRA): D001 (Ignitable)
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
62-4662-2926-7, 62-4662-4827-5, 62-4662-4828-3, 62-4662-4829-1, 70-0050-1482-7
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes Pressure Hazard - Yes
Reactivity Hazard - No
Immediate Hazard - Yes
Delayed Hazard - Yes
STATE REGULATIONS
Contact 3M for more information.
_________________________________________________________________________________________________
Page 6 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Spray-Mount(TM) Artist's Adhesive 6064, 6065
09/16/2008
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
Contact 3M for more information.
Additional Information:
++SYNTHETIC RUBBER, RESINS AND STABILIZERS
INTERNATIONAL REGULATIONS
Non hazardous according to WHMIS criteria.
Contact 3M for more information.
WHMIS: Non-hazardous
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 4 Reactivity: 0 Special Hazards: None
Aerosol Storage Code: 3
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
Revision Changes:
Section 14: ID Number(s) Template 1 was modified.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
_________________________________________________________________________________________________
Page 7 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Spray-Mount(TM) Artist's Adhesive 6064, 6065
09/16/2008
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 8 of 8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement