APC18 3V Data sheet

APC18 3V Data sheet
POWER
APC18
60 Watts
Data Sheet
Total Power: 60 Watts
Input Voltages: 3.0 - 5.5 V
# of Outputs:Single
SPECIAL FEATURES
ƒƒ Point-of-load (POL) applications)
ƒƒ High current slew rate at 2.5 A / μS1
ƒƒ Open frame SMT
ƒƒ High efficiency, 3.3 V @ 95% typical
ƒƒ Adjustable output through external
resistor programming
ƒƒ -40 °C to +85 °C ambient operating
temperature
Electrical Specifications
Input
Input voltage ra­nge
3.0 - 5.5 V
ƒƒ UVLO protection
Efficiency
3.3 V @ 95% typical
ƒƒ Positive Enable function
Control
ƒƒ Low output ripple and noise
ƒƒ Regulation to zero load
Enable
TTL compatible (positive enable
Output
SAFETY
Regulation (line, Load, Temp)
<3%
ƒƒ UL/cUL 60950 Recognized
Load current
18 A max
Ripple and noise1
50 mV
Output adjust range
0.75 V - 3.6 V
Current slew rate
up to 2.5 A / μS
ƒƒ TÜV EN60950 Licensed
Transient response
150 mV typical deviation (3.3 Vo) for 50% to 100% step load
200 μS recovery
Remote sense
10% of Vo
Turn on input voltage
3.0 V (typical)
UVLO hysteresis
300 mV (typical)
OCP/OTP
Hiccup - auto recovery
Isolation
Non-isolated module
1
APC18 Data Sheet
Environmental Specifications
Operating temperature
-40 °C to +85 °C
Storage temperature
-40 °C to +125 °C
MTBF
1 million hours
Ordering Information
Model Number
Input Voltage
Output Voltage
3.0 - 5.5 V
APC18T04-9(J)L
0.75 - 3.6 Vdc
Output Current
Efficiency (Typical)
18 A
95%
Note:
18 A max output current with total output power limited to 60 W - minimal output derating required
Typical efficiency for 3.3 V output; full load; noiminal inut voltage; 200 LFM at Ta = 25 °C
Suffix “J” designates tray packaging, non “J” is tape and reel
Mechanical Drawings
GND
VO
Notes:
TRIM SENSE
1. 200 uF and 2x 150uF input and output capacitance required.
PIN SIDE UP VIEW
VIN
2. All specifications are typical at nominal line, full load and 25°C ambient
temperature unless otherwise noted.
ENABLE
3. All specifications subject to change without notice. Mechanical drawings are for
reference only.
4. Technical Reference Notes should be consulted for detailed information
5. Warranty: One year
Recommended PAD Layout
PAD Size
MIN: 1.6 x 2.8 mm [0.065 x 0.110 inches]
REC: 1.8 x 2.8 mm [0.070 x 0.110 inches]
MAX: 2.0 x 3.0 mm [0.080 x 0.130 inches]
PIN SIDE DOWN VIEW
WORLDWIDE OFFICES
Americas
Europe (UK)
Asia (HK)
2900 S.Diablo Way
Tempe, AZ 85282
USA
+1 888 412 7832
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
+44 (0) 1384 842 211
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn
Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use
of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn
Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc.
All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective
owners. © 2015 Artesyn Embedded Technologies, Inc.
www.artesyn.com
For more information: www.artesyn.com/power
For support: [email protected]
APC18 11May2015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement