INSTALLATION PARTS INCLUDED
INSTALLATION
TRIDENT WIDE BRAKE PEDAL for GL 1800
CUSTOMER SERVICE
PARTS INCLUDED
1
1
Trident Wide Brake Pedal with Chrome Arm
Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KϋRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND NOTICES REGARDING THE USE
AND CARE OF THIS PRODUCT.
THIS INDICATION ALERTS YOU TO THE FACT THAT
IGNORING THE CONTENTS DESCRIBED HEREIN CAN
RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indication alerts you to the fact that ignoring the
contents described herein may negatively affect product
performance and functionality.
IF INSTALLING THIS PRODUCT FOR ANOTHER PARTY,
PLEASE MAKE SURE THEY RECEIVE THIS COPY OF THE
INSTALLATION INSTRUCTIONS SO THEY ARE AWARE OF
THE IMPORTANT INFORMATION CONTAINED IN THEM.
TOOLS SUGGESTED
Set of Metric Combination Wrenches, Set of Metric Hex Wrenches, Large Flat Blade Screwdriver,
FT/LBS Torque Wrench and Metric Hex Sockets
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
STEP 1
Read and understand all steps in the instructions before starting the
installation. Park the motorcycle on a hard, level surface and turn off the
ignition. Let cool.
NOTE: The larger than stock brake pedal pad on the Trident Brake Pedal may
provide easier braking. The larger pad may change the amount of
pressure needed on the pedal in any given braking situation.
Familiarize yourself with the larger pad and amount of pressure
needed.
YOU WILL BE WORKING AROUND THE ENGINE AND
EXHAUST SYSTEM DURING INSTALLATION. ENSURE THAT
THE ENGINE AND EXHAUST SYSTEM HAVE FULLY COOLED
TO PREVENT INJURY.
-cont.4077-21GL-0513
4077
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
●The product must be properly installed,
maintained and operated under
normal conditions.
●Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
●Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
●Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
●Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
●Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with
your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights
reserved.
NOTE: Marking a line on the splined brake shaft that lines up with the split in the brake arm
before beginning will give you a starting point for placement of
the new Trident Brake Pedal. PIC 1
PIC 1
REMOVE THESE
FASTENERS
STEP 2
Remove the two hex fasteners that secure the footrest mount on the
brake side. Remove the mount. Loosen the pinch bolt on the stock brake
lever. PIC 1 Set these aside, they will be reused.
STEP 3
Remove the stock brake lever from its splined mount. If this is difficult, it
may help to carefully wedge a screwdriver in the pinch slot where the
pinch bolt was removed. PIC 1 and PIC 2
SCRIBE A LINE FROM SPLIT
ON BRAKE SHAFT
STEP 4
Line up the seam in the new Trident Brake Pedal with the mark, and
install the new lever to the brake shaft. PIC 3 Install the new lever in the
same orientation as the original.
PIC 2
NOTE: It may be necessary to reach in behind the splined brake control
shaft with your finger, or a long screwdriver and hold the shaft in
place while installing the new brake lever.
STEP 5
Sit on the bike and confirm that the new lever is positioned to your liking.
If not, remove it and rotate it on the splines by one or two teeth and
reinstall. Secure the lever in place with the stock pinch bolt (Anti-seize
should be applied to these threads.) removed in Step 2.
ENSURE THE NEW BRAKE PEDAL IS POSITIONED TO
ALLOW FULL APPLICATION OF THE BRAKES WHEN
NEEDED. FAILURE TO PROPERLY POSITION THE
BRAKE PEDAL MAY CAUSE LOSS OF CONTROL
RESULTING IN SERIOUS INJURY OR DEATH.
STEP 6
PIC 3
Replace the footrest mount that was removed in Step 2 with the removed
fasteners. PIC 4 Place a drop of Blue Loctite on the threads of each
fastener and torque to 20 FT/LBS.
IT IS THE INSTALLERS RESPONSIBILITY TO TEST THE
TRIDENT BRAKE PEDAL WITH CHROME ARM FOR
PROPER FUNCTION BEFORE OPERATING THE
MOTORCYCLE. IMPROPER BRAKE PEDAL/ARM
FUNCTION MAY CAUSE LOSS OF CONTROL RESULTING
IN SERIOUS INJURY OR DEATH.
It is the installer’s responsibility to ensure that all of the
fasteners (including pre-assembled) are tightened before
operation of the motorcycle. Küryakyn will not provide
warranty coverage on products or components lost due to
improper installation or lack of maintenance. Periodic
inspection and maintenance are required on all fasteners.
LINE UP SEAM WITH
SCRIBE MARK
PIC 4
PAGE
2
Ride On!
TRIDENT BRAKE PEDAL
INSTALLATION
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement