RIGOL Installation Guide DSA800-RMSA Rackmount Kit For DSA800 Series Spectrum Analyzer

RIGOL Installation Guide DSA800-RMSA Rackmount Kit For DSA800 Series Spectrum Analyzer
RIGOL
Installation Guide
DSA800-RMSA Rackmount Kit
For DSA800 Series Spectrum Analyzer
Jan. 2012
RIGOL Technologies, Inc.
RIGOL
Guaranty and Declaration
Copyright
© 2012 RIGOL Technologies, Inc. All Rights Reserved.
Trademark Information
RIGOL is a registered trademark of RIGOL Technologies, Inc.
Publication Number
RKI06100-1110
Notices





RIGOL products are protected by patent law in and outside of P.R.C.
RIGOL reserves the right to modify or change parts of or all the
specifications and pricing policies at company’s sole decision.
Information in this publication replaces all previously corresponding material.
RIGOL shall not be liable for losses caused by either incidental or
consequential in connection with the furnishing, use or performance of this
manual as well as any information contained.
Any part of this document is forbidden to be copied or photocopied or
rearranged without prior written approval of RIGOL.
Product Certification
RIGOL guarantees this product conforms to the national and industrial standards
in China. International standard conformance certification is in progress, e.g. ISO.
Contact Us
If you have any problem or requirement when using our products, please contact
RIGOL Technologies, Inc. or your local distributors, or visit: www.rigol.com
DSA800-RMSA Installation Guide
I
RIGOL
Safety Terms and Symbols
Terms in this Manual. These terms may appear in this manual:
WARNING
Warning statements indicate the conditions or practices that could
result in injury or loss of life.
CAUTION
Caution statements indicate the conditions or practices that could result
in damage to this product or other property.
Terms on the Product. These terms may appear on the Product:
DANGER
indicates an injury or hazard may immediately happen.
WARNING indicates an injury or hazard may be accessible potentially.
CAUTION indicates a potential damage to the instrument or other property
might occur.
Symbols on the Product. These symbols may appear on the product:
Hazardous
Voltage
II
Refer to
Instructions
Protective
Earth
Terminal
Chassis
Ground
Test
Ground
DSA800-RMSA Installation Guide
RIGOL
Content
Guaranty and Declaration .........................................................................I
Safety Terms and Symbols ...................................................................... II
Product Overview .................................................................................... 1
Kit Parts List ............................................................................................ 1
Space Requirements for Installation ........................................................... 3
Installation Introduction ......................................................................... 4
Installation Tool ....................................................................................... 4
Installation Procedures.............................................................................. 4
Installation Cautions ................................................................................. 7
DSA800-RMSA Installation Guide
III
RIGOL
Product Overview
DSA800-RMSA, the rackmount kit of DSA800 series spectrum analyzer, as shown
below, is used to mount your analyzer into a standard 19-inch machine cabinet.
Kit Parts List
No.
Name
Qty.
1
2
3
4
5
6
7
8
9
10
Front Panel
Left Plate
M4 Screw
Spring Washer
Washer
Support Board
Retaining Bracket
Right Plate
M6 Screw
M6 Nut
1
1
14
4
4
1
2
1
4
4
DSA800-RMSA Installation Guide
Description
M4 x 8 Cross Recessed Pan Head Screw
M6*16 Phil-Slot Pan Head Screw
M6*5 Lock Blade Square Nut
1
RIGOL
4
3
2
5
6
7
1
8
3
2
9
10
DSA800-RMSA Installation Guide
RIGOL
Space Requirements for Installation
The following requirements must be fulfilled by the machine cabinet in which the
instrument is mounted.



Dimension of the machine cabinet must be standard 19-inch.
At least 5U (222.2mm) space should be provided by the machine cabinet.
The depth inside the machine cabinet should not be less than 200 mm.
The dimension of the instrument after being installed is shown below (the unit is
mm).
482.6
220.6
133.35
207.5
465
403
172.2
DSA800-RMSA Installation Guide
3
RIGOL
Installation Introduction
Installation Tool
PH2 Phillips Screwdriver (recommended)
Installation Procedures
CAUTION
Only authorized operators can execute the installation operation because
that the instrument will be damaged or installed in machine cabinet
incorrectly if the installation is not proper.
1.
4
Install the right and left plates: aim the detents of the right and left plates at
the openings on the support board and insert respectively, then fix them using
four M4 screws.
DSA800-RMSA Installation Guide
RIGOL
2.
Install the front panel: let the screw holes fit well together and fix them with
six M4 screws.
3.
Place and fix the instrument: place the instrument into the confined position
on the support board. Aiming the instrument front panel at the opening of the
front panel of the rackmount kit and fix the instrument with four spring
washers, four washers, two retaining brackets and four M4 screws.
DSA800-RMSA Installation Guide
5
RIGOL
4.
6
Load into the machine cabinet: mount the rack with instrument fixed into a
standard 19-inch machine cabinet using four M6 screws and square nuts.
DSA800-RMSA Installation Guide
RIGOL
Installation Cautions
The rack holds a height of 5U, and the holes pointed out by the arrows are the
mounting holes for the rack.
5U
DSA800-RMSA Installation Guide
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement