SHOWER TRAY INSTRUCTION 40mm Rectangle Shower Tray 1400mm x 800mm x 40mm

SHOWER TRAY INSTRUCTION 40mm Rectangle Shower Tray 1400mm x 800mm x 40mm
to
o
ls
SHOWER TRAY
INSTRUCTION
re
qu
ire
d
40mm Rectangle Shower Tray
1400mm x 800mm x 40mm
ON FLOOR INSTALLATION
1
2
Please note on the rear of the tray are 15
green caps that should only be removed if
legs and panels are to be used.
Ensure that the location of the shower tray is firm, level,
and clean.
Remove protective plastic film from the areas near the waste
and those sides of the tray which will be against a wall.
4
3
Install the shower tray on a 15mm depth of weak cement
mix (sand/cement ratio 5:1). Tile adhesive can be used as
an alternate to sand or cement.
Please note if using water based adhesives, to enhance the
bonding it is suggested that a suitable primer is applied to
the base of the shower tray before installation.
It is recommended that the ‘easyseal’ water sealing strip
should be installed at the sides against wall.
For the detailed installation method,
please refer to the “Waterproof Sealing Strip instruction”.
1
1-4
A
ON FLOOR INSTALLATION
6
5
Fit the shower tray waste.
Ensure the ‘easyseal’ water sealing strip is flat to the wall.
Place the shower tray onto the cement bed and apply
gentle pressure with the palm of the hand to bed the tray
into position.
7
8
Level the tray and allow to set.
2
When shower tray is set remove the remainder of the
protective plastic film and connect the waste pipe and
check for leakage.
Option:
9
* If the ‘easyseal’ water sealing strip is not installed,
please seal joints between tray and wall with an
anti fungal silicone sealant and allow to set.
Tile and seal joints with an anti fungal silicone sealant
and allow to set.
2-4
A
RAISED INSTALLATION
Parts Supplied:
M5*12mm
8x
8x
1x
15x
1
1a
1x
2
1b
Turn the tray over and use the cardboard packaging as a
protective mat. Remove the green caps, and insert the feet
to the indicated positions.
Screw the panel clips into position on the side that the panels
will be attached.
4
3
100mm
Turn the tray over. Remove protective plastic film from the
areas near the waste and those sides of the tray which will be
against a wall.
Fit the shower tray waste.
All feet should be adjusted to 100mm.
5
3
6
Ensure the 'easyseal' water sealing strip is flat to the wall.
Place the tray into position and level both ways using the
legs. After the tray has been levelled adjust all the inner
feet to stabilise the tray. When level fix these legs to the
floor with silicon sealant or 'no more nails' type adhesive.
It is recommended that the ‘easyseal’ water sealing strip
should be installed at the sides against wall.
For the detailed installation method,
please refer to the “Waterproof Sealing strip instruction”.
3-4
A
RAISED INSTALLATION
7
Option:
When shower tray is set remove the remainder of the
protective plastic film and connect the waste pipe and
check for leakage.
* If the ‘easyseal’ water sealing strip is not installed,
please seal joints between tray and wall with an
anti fungal silicone sealant and allow to set.
8
9
h
t
ng
ay
r
T
le
Ensure the rebated end is included
in the length required.
Mark the length of panel required for both edges and
cut with a junior or standard hacksaw.
Tile the wall and seal joints with an anti fungal silicone
sealant and allow to set.
11
10
First fix the rebated panel pushing it firmly on to the panel
clips. Then fix the remaining panel in the same manner.
4
4-4
A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement