FEATURES TYPICAL SPECIFICATIONS

FEATURES TYPICAL SPECIFICATIONS
Type:
Project/Location:
Contractor:
GRANDE™ Series
Prepared By:
Date:
Thermoplastic Pictogram
Combination Unit
Model No.:
FEATURES
TYPICAL SPECIFICATIONS
The Grande Series of combination units (unit equipment and pictogram exit
sign) are designed to complement designer’s look and ease of installation
with performance and cost-competitiveness.
Supply and install Lumacell® Grande™ Series combination of unit equipment
and pictogram exit sign. The unit frame and face plates shall be made of
injection-molded thermoplastic. The faceplates shall feature a uniformly
illuminated legend. The light source shall be long-life white light-emitting
diodes (LED). The unit shall be equipped with two emergency heads with
tool-less adjustable swivels and long-life MR-16 LED lamps of ___ V and
___ W. Each lamp shall be protected by a snap-on, shock-absorbent,
transparent polycarbonate cover.
The AC input voltage shall be standard 120/347VAC 60Hz. The unit shall be
equipped with a test switch and a green pilot light, located on the face plate
above the pictogram legend. The battery charger shall be driven by a microcontroller. All electronic circuitry (charger, LED driver, signage LED’s) shall be
installed on a single printed circuit board PCB. The unit equipped with selftesting / self-diagnostic features shall automatically self test for one minute
every 30 days, 10 minutes in the 6th month and 30 minutes annually. When a
fault is detected, the bi-color pilot-light shall turn from green to red and shall
flash following a particular code. The code description shall be displayed on a
label next to the pilot light to identify the failure type: battery, charger circuitry,
LED lamps for signage, or emergency lights.
The combination unit shall meet or exceed the standard CSA C22.2 No.141-10
.
The equipment shall be Lumacell® Model:
™
•One-pack combination of battery unit and Pictogram Sign, a compact
and contemporary design
•Durable injection-molded thermoplastic housing with push-to-snap
design
•Available in single or double face configurations both with means for
ceiling mounting
•Supplied standard with two (single face) or three pictogram films
(universal face) for direction selection
•Two MR16 LED or halogen lamps, shielded by a clear polycarbonate
cover
•Twin LED lights provide up to 89 feet of egress illumination on a 6-foot
wide path
•Remote load capacity: one unit equipment with LED remote lights
covers up to 712 feet (217m) of egress illumination
•Sealed, maintenance-free, Lead-Calcium or Nickel-Metal-Hydride
batteries
•Dual voltage input: 120/347VAC or 120/277VAC
•Comes standard with non-audible auto-diagnostics
•Optional vandal-resistant shield with tamper-proof screws
•Certified CSA C22.2 No.141
•Optional: Nexus® Compatible
WIRE GUARDS
460.0078-L
Wall Mount
IN THE SAME FAMILY: THERMOPLASTIC
- Grande™ Series Thermoplastic
Exit Unit
p. 58
p. 59
- Grande Series Thermoplastic
Battery Unit
™
p. 108-109
60
www.lumacell.com
- Grande™ Series
Thermoplastic Combination
Unit
Type:
Project/Location:
Contractor:
GRANDE™ Series
Prepared By:
Date:
Thermoplastic Pictogram
Combination Unit
Model No.:
DIMENSIONS
Dimensions are approximate and subject to change.
11-1/4” [28.7 cm]
12-3/8” [31.5 cm]
4-7/8” [12.3 cm]
< PICTO
LEFT FROM HERE
17” [43.2 cm]
PICTO
STRAIGHT FROM HERE
PICTO >
RIGHT FROM HERE
3-3/8” [8.5 cm]
POWER CONSUMPTION
MODEL
AC SPECS
Pictogram Sign module
30MIN
1H
WATTAGE CAPACITY
1H30
2H
-
-
-
-
-
25
15
12
8
-
Less than 4W
2L
0.12/0.04 A
5L
120/347VAC
12L5
12H5
0.24/0.08 A
12H10
4H
50
30
24
16
8
50
30
24
16
8
50
36
24
18
9
100
72
48
36
18
ORDERING INFORMATION
SERIES
2L= 6V-25W
Lead-Calcium
5L= 6V-50W
Lead-Calcium
12L5= 12V-50W
Lead-Calcium
12H5= 12V-50W
NiMH
12H10= 12V-100W
NiMH
FACE/
MOUNTING
# OF
HEADS
HEAD STYLE &
WATTAGE
GRAP1=single face
ceiling or
wall mount
GRAP2= double
face ceiling
mount
GRAP1N= single face
wall mount
(less
canopy)
GRAPU= universal
two faces
backplate
and canopy
Blank= no
heads
2= two heads
LD1= MR16 LED, 6V-4W
LD7= MR16 LED, 12V-4W
LD9= MR16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
M6= MR16, 6V-6W
M10= MR16, 6V or 12V-10W
M12= MR16, 12V-12W
M20= MR16, 12V-20W
COLOUR
B= black
W= factory
white
VOLTAGE
2= 120/277VAC
3= 120/347VAC
CHARGER
TYPE
Blank= auto-test,
nonaudible
AT= auto-test
NEX= NEXUS®
system
interface
NEXRF= wireless
NEXUS®
system
interface
OPTIONS
Blank= no options
TP= tamper proof screws*
T3= time delay (15 minutes)
VRTP1= polycarbonate
shield with tamper
proof screws,
single face*
VRTP2= polycarbonate
shield with tamper
proof screws,
double face*
*091957-L= t amper proof bit
(sold seperately)
*VRTP1 & VRTP2 are not
available with GRAPU.
EXAMPLE: 2LGRAP22M6W3
www.lumacell.com
61
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement