#546 INSTRUCTIONS

#546 INSTRUCTIONS
STROBE
Mars Light
T1 (3mm) Incandescent White
Super Bright LED
#545
#546
T1 (3mm)
Incandescent
White LED
mounted on
an engine,
caboose, or
other location.
Installation Instructions:
Installation Instructions:
Locate a position to place the STROBE pc board. Drill a 1/8" hole
for the LED. If you choose to extend the LED from the main
board, it is important to connect the LED leads in the same
polarity. Having them reversed will cause the LED to not
illuminate and may burn out the LED.
Position the STROBE, making sure the area is clean of grease
for proper adhesion, peel tape covering and place in position.
Locate a position to drill a 1/8" hole for the LED if needed. Otherwise, use
the existing lens and mount the board and LED within the appropriate
area.
Position the MARS, making sure the area is clean of grease for proper
adhesion, peel tape covering and place in position. You may wish to
remove the LED and locate it elsewhere. If you choose to extend the LED
from the main board, it is important to connect the LED leads in the same
polarity. Having them reversed will cause the LED to not illuminate and
may burn out the LED.
DC operators - connect the red / black wires to the track power pickup (red
- right rail, black - left rail).
Connect the input wires to either a 9 Volt battery or cut the battery
snap end off and connect wires to the track pickup shoes (polarity
of the wires is not important). Input power can be from DC, AC, or
DCC and up to 20 volts. If utilizing a battery, an on/off switch (Item
#524) may be desired.
AC operators - when using an E-Unit similar to our item #518 or #400, or
other DC motor type engine, connect the red and black wires to the motor
leads. If the MARS operates when the engine is in reverse, merely reverse
the input wires. Otherwise, connect the red and black wires to the AC track
power. By doing this, the MARS will not be directional but on whenever
track power is present.
Be sure not to short the LED leads, or any other parts to any
other metal part, this will damage the STROBE.
Be sure not to short the LED leads, or any other parts to any other metal
part, this will damage the MARS.
246 W. Main St.
Leola, PA 17540
(717) 661-7041
www.dallee.com
246 W. Main St.
Leola, PA 17540
(717) 661-7041
www.dallee.com
F.R.E.D.
BEACON
#556
T1 (3mm) - RED LED
#557
LED
Installation Instructions:
Locate a position to place the FRED pc board. You may want to
make two slits to accomodate the LED leads without removing it.
If you choose to extend the LED from the main board, it is
important to connect the LED leads in the same polarity. Having
them reversed will cause the LED to not illuminate and may burn
out the LED.
Position the FRED, making sure the area is clean of grease for
proper adhesion, peel tape covering and place in position.
Connect the input wires to either a 9 Volt battery or cut the battery
snap end off and connect wires to the track pickup shoes (polarity
of the wires is not important). Input power can be from DC, AC, or
DCC and up to 20 volts. If utilizing a battery, an on/off switch (Item
#524) may be used.
Be sure not to short the LED leads, or any other parts to any
other metal part, this will damage the FRED.
246 W. Main St.
Leola, PA 17540
(717) 661-7041
www.dallee.com
Installation Instructions:
Locate a position to place the BEACON pc board. If you choose
to extend the LED from the main board, it is important to connect
the LED leads in the same polarity. Having them reversed will
cause the LED to not illuminate and may burn out the LED.
Position the BEACON, making sure the area is clean of grease
for proper adhesion, peel tape covering and place in position.
Connect the input wires to either a 9 Volt battery or cut the battery
snap end off and connect wires to the track pickup shoes (polarity
of the wires is not important) or a fixed voltage source. Input
power can be from DC, AC, or DCC and up to 20 volts. If utilizing
a battery, an on/off switch (Item #524) may be used.
Be sure not to short the LED leads, or any other parts to any
other metal part, this will damage the BEACON.
246 W. Main St.
Leola, PA 17540
(717) 661-7041
www.dallee.com
Dual Mars Light
#547
Two T1 (3mm)
Incandescent
White LED 's
Installation Instructions: Locate a position to drill two 1/8" holes for
the LED's if needed. Otherwise, use the existing lens and mount the
board and LED's within the appropriate area.
Position the MARS, making sure the area is clean of grease for
proper adhesion, peel tape covering and place in position. You may
wish to remove the LED's to locate elsewhere. If you choose to
extend the LED's from the main board, it is important to connect the
LED's leads in the same polarity. Having them reversed will cause
the LED's to not illuminate and may burn out the LED's. Never
operate this unit with one LED!
DC operators - connect the red / gray wires to the track power pickup
(red - right rail, gray - left rail).
AC operators - when using an E-Unit similar to our item #518 or
#400, or other DC motor type engine, connect the red and gray wires
to the motor leads. If the MARS operates when the engine is in
reverse, merely reverse the input wires. Otherwise, connect the red
and gray wires to the AC track power. By doing this, the MARS will
not be directional but on whenever track power is present.
Be sure not to short the LED's leads, or any other parts to any other
metal part, this will damage the MARS light.
246 W. Main St.
Leola, PA 17540
(717) 661-7041
www.dallee.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement