TRF37B73 1-6000 MHz RF Gain Block 1 Features 3 Description

TRF37B73 1-6000 MHz RF Gain Block 1 Features 3 Description
Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
TRF37B73
SLASE41 – MAY 2014
TRF37B73 1-6000 MHz RF Gain Block
1 Features
3 Description
•
•
•
•
•
•
•
•
•
•
The TRF37B73 is packaged in a 2.00mm x 2.00mm
WSON with a power down pin feature making it ideal
for applications where space and low power modes
are critical.
2 Applications
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
General Purpose RF Gain Block
Consumer
Industrial
Utility Meters
Low-cost Radios
Cellular Base Station
Wireless Infrastructure
RF Backhaul
Radar
Electronic Warfare
Software-defined Radio
Test and Measurement
Point-to-Point/Multipoint Microwave
Software Defined Radios
RF Repeaters
Distributed Antenna Systems
LO and PA Driver Amplifier
Wireless Data, Satellite, DBS, CATV
IF Amplifier
The TRF37B73 is designed for ease of use. For
maximum flexibility, this family of parts uses a
common 3.3 V supply and consumes 52 mA. In
addition, this family was designed with an active bias
circuit that provides a stable and predictable bias
current over process, temperature and voltage
variations. For gain and linearity budgets the device
was designed to provide a flat gain response and
excellent OIP3 out to 6000 MHz. For space
constrained applications, this family is internally
matched to 50 Ω, which simplifies ease of use and
minimizes needed PCB area.
Device Information(1)
PART NUMBER
TRF37B73
PACKAGE
WSON (32)
BODY SIZE (NOM)
2.00mm x 2.00mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Simplified Schematic
VCC
VCC
1
2
C1
1000pF
8
Output
Match
1 MHz – 6000 MHz
Gain: 14.5 dB
Noise Figure: 4 dB
Output P1dB: 15 dBm at 2000 MHz
Output IP3: 27 dBm at 2000 MHz
Power Down Mode
Single Supply: 3.3 V
Stabilized Performance Over Temperature
Unconditionally Stable
Robust ESD: >1 kV HBM; >1 kV CDM
Input
Match
1
L1
RF choke
100nH
7
3
6
4
5
C2
1000pF
PWDN
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TRF37B73
SLASE41 – MAY 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
4
4
4
4
5
5
6
Absolute Maximum Ratings ......................................
Handling Ratings.......................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Timing Requirements ................................................
Typical Characteristics ..............................................
7.2 Functional Block Diagram ......................................... 8
7.3 Feature Description................................................... 8
7.4 Device Functional Modes.......................................... 8
8
Applications and Implementation ........................ 9
8.1 Application Information.............................................. 9
8.2 Typical Application ................................................... 9
9 Power Supply Recommendations...................... 10
10 Layout................................................................... 11
10.1 Layout Guidelines ................................................. 11
10.2 Layout Example .................................................... 11
11 Device and Documentation Support ................. 12
11.1 Trademarks ........................................................... 12
11.2 Electrostatic Discharge Caution ............................ 12
11.3 Glossary ................................................................ 12
Detailed Description .............................................. 8
12 Mechanical, Packaging, and Orderable
Information ........................................................... 12
7.1 Overview ................................................................... 8
4 Revision History
2
DATE
REVISION
NOTES
May 2014
*
Initial release.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TRF37B73
TRF37B73
www.ti.com
SLASE41 – MAY 2014
5 Pin Configuration and Functions
DSG PACKAGE
(TOP VIEW)
8
NC
RFIN
2
7
RFOUT
NC
3
6
NC
NC
4
5
PWDN
Output
Match
1
Input
Match
VCC
Pin Functions
PIN
NAME
VCC
RFIN
NC
DESCRIPTION
NO.
1
DC Bias.
2
RF input. Connect to an RF source through a DC-blocking capacitor. Internally matched to 50 Ω.
3, 4, 6, 8
No electrical connection. Connect pad to GND for board level reliability integrity.
PWDN
5
When high the device is in power down state. When LOW or NC the device is in active state. Internal pulldown
resistor to GND.
RFOUT
7
RF Output and DC Bias (VCC). Connect to DC supply through an RF choke inductor. Connect to output load
through a DC-blocking capacitor. Internally matched to 50 Ω.
GND
PowerPAD™ RF and DC GND. Connect to PCB ground plane.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TRF37B73
3
TRF37B73
SLASE41 – MAY 2014
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1)
Supply Input voltage
MIN
MAX
UNIT
–0.3
3.6
V
10
dBm
–40
150
°C
Input Power
Operating virtual junction temperature range
(1)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 Handling Ratings
TSTG
VESD
(1)
(2)
MIN
MAX
UNIT
–65
150
°C
Human body model (HBM), per ANSI/ESDA/JEDEC
JS-001, all pins (1)
–1
1
kV
Charged device model (CDM), per JEDEC
specification JESD22-C101, all pins (2)
–1
1
kV
Storage temperature range
Electrostatic discharge
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
Supply Voltage, VCC
Operating junction temperature, TJ
MIN
NOM
MAX
3
3.3
3.45
V
125
°C
–40
UNIT
6.4 Thermal Information
THERMAL METRIC (1)
DSG
8 PINS
RθJA
Junction-to-ambient thermal resistance
79.3
RθJCtop
Junction-to-case (top) thermal resistance
110
RθJB
Junction-to-board thermal resistance
49
ψJT
Junction-to-top characterization parameter
6
ψJB
Junction-to-board characterization parameter
49.4
RθJCbot
Junction-to-case (bottom) thermal resistance
19.2
(1)
4
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TRF37B73
TRF37B73
www.ti.com
SLASE41 – MAY 2014
6.5 Electrical Characteristics
VCC = 3V3, TA = 25°C, PWDN = Low, LOUT = 100 nH, C1 = C2 = 1000 pF, ZS = ZL = 50 Ω (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
52
65
UNIT
DC PRAMETERS
ICC
Pdiss
Total supply current
Power down current
PWDN = High
Power dissipation
mA
125
µA
0.172
W
RF FREQUENCY RANGE
Frequency range
G
Small signal gain
1
6000
MHz
fRF = 400 MHz
15.5
dB
fRF = 2000 MHz
14.5
dB
fRF = 3000 MHz
14.5
dB
fRF = 4000 MHz
14
dB
fRF = 5000 MHz
13
dB
fRF = 6000 MHz
11.5
dB
OP1dB
Output 1dB compression point
At 2000 MHz
15
dBm
OIP3
Output 3rd order intercept point
At 2000 MHz, 2-tone 10 MHz apart
27
dBm
NF
Noise figure
At 2000 MHz
4
dB
R(LI)
Input return loss
At 2000 MHz
20
dB
R(LO)
Output return loss
At 2000 MHz
16
dB
PWDN PIN
VIH
High level input level
VIL
Low level input level
2
V
IIH
High level input current
30
µA
IIL
Low level input current
1
µA
0.8
V
6.6 Timing Requirements
MIN
TYP
MAX
UNIT
PWDN PIN
tON
Turn-on Time
50% TTL to 90% POUT
0.6
µs
tOFF
Turn-off Time
50% TTL to 10% POUT
1.4
µs
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TRF37B73
5
TRF37B73
SLASE41 – MAY 2014
www.ti.com
17
17
16
16
15
15
14
14
13
13
Gain (dB)
Gain (dB)
6.7 Typical Characteristics
12
11
3.45V
10
3.3V
9
12
11
10
9
3.15V
8
-40ƒC
25ƒC
85ƒC
8
3.0V
7
7
0
1000
2000
3000
4000
5000
Frequency (MHz)
VCC curves
6000
0
1000
Temp = 25°C
Pin = –10 dBm
2000
3000
4000
5000
6000
Frequency (MHz)
C001
C002
3
Temp curves
VCC = 3.3 V
Pin = –10 dBm
Figure 1. Gain vs Frequency
17
16
16
15
15
14
14
OP1dB (dBm)
OP1dB (dBm)
Figure 2. Gain vs Frequency
17
13
12
11
3.45V
10
3.3V
9
13
12
11
10
9
3.15V
8
-40ƒC
25ƒC
85ƒC
8
3.0V
7
7
0
1000
2000
3000
4000
5000
Frequency (MHz)
VCC curves
6000
0
Temp curves
33
33
31
31
29
29
27
25
21
3.3V
19
5000
6000
C004
VCC = 3.3 V
-40ƒC
25ƒC
85ƒC
27
25
23
19
17
3.0V
15
15
0
1000
2000
3000
4000
Frequency (MHz)
VCC curves
Temp = 25°C
5000
6000
0
1000
Pin = –10 dBm/tone
2000
3000
4000
Frequency (MHz)
C003
Temp curves
Figure 5. OIP3 vs Frequency
6
4000
21
3.15V
17
3000
Figure 4. OP1dB vs Frequency
35
OIP3 (dBm)
OIP3 (dBm)
Figure 3. OP1dB vs Frequency
35
3.45V
2000
Frequency (MHz)
Temp = 25°C
23
1000
C003
VCC =3.3 V
5000
6000
C004
Pin = –10 dBm/tone
Figure 6. OIP3 vs Frequency
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TRF37B73
TRF37B73
www.ti.com
SLASE41 – MAY 2014
Typical Characteristics (continued)
6.5
6.5
-40ƒC
25ƒC
85ƒC
3.45V
6
3.3V
5.5
5.5
3.15V
5
5
3.0V
NF (dB
4.5
4.5
4
4
3.5
3.5
3
3
2.5
2.5
0
1000
2000
3000
4000
5000
Frequency (MHz)
VCC curves
0
6000
1000
Temp = 25°C
Temp curves
Figure 7. NF vs Frequency
3000
4000
5000
6000
C004
VCC = 3.3 V
Figure 8. NF vs Frequency
60
60
3.45V
3.3V
3.15V
3.0V
57
-40ƒC
25ƒC
85ƒC
57
54
54
Icc (mA)
Icc (mA)
2000
Frequency (MHz)
C003
51
51
48
48
45
45
0
1000
2000
3000
4000
5000
Frequency (MHz)
VCC curves
0
6000
1000
Temp = 25°C
Temp curves
3000
4000
5000
6000
C004
VCC = 3.3 V
Figure 10. ICC vs Frequency
0
16
-5
14
-10
12
-15
10
-20
8
0. 5
2.0
1. 8
1.4
1.6
1.0
1.2
0.9
0.8
0.6
0.7
Figure 9. ICC vs Frequency
0.
4
3.0
0. 3
4.0
0 .2
0.1
10
20
3.0
4.0
5.0
1.6
1.8
2.0
1.2
1.4
0.8
0.9
1.0
0.6
0.7
0.5
0.3
0.4
0.1
0.2
20
-20
-0.1
Sxx (dB)
5.0
10
-25
-0.2
-5 .0
-4.
0
3
-0.
.0
- 1.6
-1.4
-1.2
-1.0
-0.9
-0.8
-0.7
S11
4
-35
S12
2
S21
-40
8
-1.
.0
-2
.5
-0
-0.
6
-30
-3
.4
-0
6
S22
-10
S(1,1)
S(2,2)
2000
Frequency (MHz)
C003
S21 (dB)
NF (dB)
6
0
0
1000 2000 3000 4000 5000 6000 7000 8000
Frequency (MHz)
C016
freq (1.000MHz to 8.000GHz)
VCC = 3.3 V
Temp = 25°C
1 MHz to 8 GHz
Data Taken with EVM and Bias T, De-embedded to DUT pin
VCC = 3.3 V
Temp = 25°C
1 MHz to 8 GHz
Data Taken with EVM and Bias T, De-embedded to DUT pin
Figure 11. Smith Chart – S11, S22
Figure 12. S22, S11, S12, S21
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TRF37B73
7
TRF37B73
SLASE41 – MAY 2014
www.ti.com
7 Detailed Description
7.1 Overview
The device is a 3.3 V general purpose RF gain block. It is a SiGe Darlington amplifier with integrated 50 Ω input
and output matching. The device contains an active bias circuit to maintain performance over a wide temperature
and voltage range. The included power down function allows the amplifier to shut down saving power when the
amplifier is not needed. Fast shut down and start up enable the amplifier to be used in a host of time division
duplex applications.
7.2 Functional Block Diagram
VCC
Output
Match
RF Input
Active Bias and
Temperature
Compensation
Input
Match
Power Down
VCC
RF Output
7.3 Feature Description
The TRF37B73 is a fixed gain RF amplifier. It is internally matched to 50 Ω on both the input and output. It is a
fully cascadable general purpose amplifier. The included active bias circuitry ensures the amplifier performance
is optimized over the full operating temperature and voltage ranges.
7.4 Device Functional Modes
7.4.1 Power Down
The TRF37B73 PWDN pin can be left unconnected for normal operation or a logic-high for disable mode
operation. For applications that use the power down mode, normal 5 V TLL levels are supported.
8
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TRF37B73
TRF37B73
www.ti.com
SLASE41 – MAY 2014
8 Applications and Implementation
8.1 Application Information
The TRF37B73 is a wideband, high performance, general purpose RF amplifier. To maximize its performance,
good RF layout and grounding techniques should be employed.
8.2 Typical Application
The TRF37B73 device is typically placed in a system as illustrated in Figure 13.
VCC
C5
DC Bypass
Capacitor
C4
RF Bypass
Capacitors
C3
L1
RF In
1
VCC
8
2
RFIN
RFOUT 7
C1
3
DC Blocking
Capacitor
4
PWDN
RF Choke
Inductor
RF Out
6
C2
5
DC Blocking
Capacitor
Figure 13. Typical Application Schematic for TRF37B73
8.2.1 Design Requirements
Table 1. Design Parameters
PARAMETERS
EXAMPLE VALUES
Input power range
< 3 dBm
Output power
< 18 dBm
Operating frequency range
1 — 6000 MHz
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TRF37B73
9
TRF37B73
SLASE41 – MAY 2014
www.ti.com
8.2.2 Detailed Design Procedure
The TRF37B73 is a simple to use internally matched and cascadable RF amplifier. Following the recommended
RF layout with good quality RF components and local DC bypass capacitors will ensure optimal performance is
achieved. TI provides various support materials including S-Parameter and ADS models to allow the design to be
optimized to the user's particular performance needs.
22
22.0
20
20.0
18
18.0
16
16.0
14
14.0
12
12.0
OP1dB
10
10.0
NF
8
8.0
6
6.0
4
4.0
2
2.0
0
0
1000
NF (dB)
OP1dB (dBm)
8.2.3 Application Curve
2000
3000
4000
5000
0.0
6000
Frequency (MHz)
C017
Figure 14. OP1dB and NF vs Frequency
9 Power Supply Recommendations
All supplies may be generated from a common nominal 3.3 V source but should be isolated through decoupling
capacitors placed close to the device. The typical application schematic in Figure 13 is an excellent example.
Select capacitors with self-resonant frequency near the application frequency. When multiple capacitors are used
in parallel to create a broadband decoupling network, place the capacitor with the higher self-resonant frequency
closer to the device. Expensive tantalum capacitors are not needed for optimal performance.
10
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TRF37B73
TRF37B73
www.ti.com
SLASE41 – MAY 2014
10 Layout
10.1 Layout Guidelines
Good layout practice helps to enable excellent linearity and isolation performance. An example of good layout is
shown in Figure 15. In the example, only the top signal layer and its adjacent ground reference plane are shown.
• Excellent electrical connection from the PowerPAD™ to the board ground is essential. Use the recommended
footprint, solder the pad to the board, and do not include solder mask under the pad.
• Connect pad ground to device terminal ground on the top board layer.
• Verify that the return DC and RF current path have a low impedance ground plane directly under the package
and RF signal traces into and out of the amplifier.
• Ensure that ground planes on the top and any internal layers are well stitched with vias.
• Do not route RF signal lines over breaks in the reference ground plane.
• Avoid routing clocks and digital control lines near RF signal lines.
• Do not route RF or DC signal lines over noisy power planes. Ground is the best reference, although clean
power planes can serve where necessary.
• Place supply decoupling close to the device.
10.2 Layout Example
VCC
DC Bypass
Capacitor
Note: Single DC bypass capacitor
can be used as long as it is close to
the pin 1 and is tied to the common
ground plane
DC Bypass
Capacitor
RF Bypass
Capacitors
RF Choke
Inductor
VCC 11
RF In
88
NC
RFIN
22
77 RFOUT
NC
33
66
NC
44
55 PWDN
DC Blocking
Capacitor
NC
RF Out
DC Blocking
Capacitor
Note: Ensure good RF microstrip or stripline traces are
used to connect the external components to the RF input
and output pins
Note: Ensure all components are connected to a common
RF/DC ground plane with plenty of vias
Figure 15. Layout
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TRF37B73
11
TRF37B73
SLASE41 – MAY 2014
www.ti.com
11 Device and Documentation Support
11.1 Trademarks
PowerPAD is a trademark of Texas Instruments.
11.2 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.3 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
12
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: TRF37B73
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
TRF37B73IDSGR
ACTIVE
WSON
DSG
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
B73I
TRF37B73IDSGT
ACTIVE
WSON
DSG
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
B73I
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2014
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Dec-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TRF37B73IDSGR
WSON
DSG
8
3000
180.0
8.4
2.3
2.3
1.15
4.0
8.0
Q2
TRF37B73IDSGT
WSON
DSG
8
250
180.0
8.4
2.3
2.3
1.15
4.0
8.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Dec-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TRF37B73IDSGR
WSON
DSG
8
3000
210.0
185.0
35.0
TRF37B73IDSGT
WSON
DSG
8
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement