PODHY1GV6 Manual
Expand Your Factory Radio
add
iPod
®
HY1
Owner’s Manual
Neo Gateway
Enjoy The Music
Table of Contents
1.
2.
3.
4.
Introduction
Precautions
Compatibility Notes
Dipswitch Settings
Pages
2
2
2
3
5. Installation
3
6. iPod Operation
4
7. HD Radio Operation
5
8. Selecting AUX Input
6
9. Selecting Factory Satellite
6
10. Troubleshooting
11. Warranty Info
7
8
(if equipped)
(if equipped)
Neo Gateway & Optional Add-ons
Factory Radio
Not Included
iPod
Not Included
Neo Gateway Harness
Neo Gateway
11Ft. iPod Cable
3Ft. HD Radio Cable
(sold with HDRT)
HD RadioTM Tuner
(sold seperately)
1
1. Introduction
Thank you for purchasing the ® Neo Gateway. The Neo Gateway is designed to
provide endless hours of listening pleasure from your factory radio. To ensure that
your iPod performs correctly with your radio, we recommend that you read this
entire manual before attempting installation of the Neo Gateway.
The Neo Gateway allows connectivity for iPod and the HD Radio tuner (HDRT sold
separately), enabling full control of these devices from the factory installed radio.
It also retains original system features such as satellite radio (if equipped).
2. Precautions
UPDATING iPod FIRMWARE
For proper operation of the Neo Gateway, your iPod must be updated with the most
recent version of firmware from Apple. This is done on your computer. To update the
software on the iPod go to: http://www.apple.com/ipod/download/.
Follow the directions on the website to complete the download. There is no charge for
this update.
PREVENTING DAMAGE TO YOUR VEHICLE OR iPod.
To eliminate the risk of an electrical short, we recommend disconnecting the
vehicle’s battery prior to installation. If you do not feel comfortable making these
connections, we suggest you seek professional installation. We recommend that the
iPod be disconnected from the interface when the vehicle is not in use.
PROPER MOUNTING LOCATION
Securely install the interface in a location free from; heat, humidity, moving parts,
sharp metal edges or direct sunlight. We recommend securing the interface to a
suitable location using; double sided tape, VelcroTM or zip-ties.
3. Compatibility Notes
Radio Requirements
Radio must have a button labeled “XM” to support the Neo Gateway.
2
4. Dipswitch Settings
For standard operation of the Neo Gateway, all four dip-switches need to be OFF
(up) prior to installation.
OFF
ON
Fig. 1 Side view of interface with dip switches in correct position
5. Installation
1. When making electrical connections it is always recommended that the
vehicle’s battery be disconnected from the electrical system before performing
the installation.
2. Carefully remove the trim panels covering the bolts that secure the radio into the
dash cavity. Remove these bolts, and carefully pull the radio from the dash of the
vehicle. This will provide access to the factory radio connectors where you will connect
the Neo Gateway harness.
3. Disconnect the factory harness from the back of the radio. Disconnect the antenna
adaptor from the radio.
4. Connect the 8-Pin iPod docking cable into the first port on the Neo Gateway furthest
away from dipswitches. Carefully run the 11 foot iPod cable behind the dash to the
location where the iPod will be mounted or stored (for example; the glove box or center
console). This location will vary based on the vehicle, and customer’s preference.
When running this cable through the dash, be sure to secure it away from moving parts
or sharp metal edges that may damage the cable.
5. If connecting the HD Radio tuner (HDRT sold separately) Plug the 3 foot HD Radio
Cable (8-Pin to 8-Pin) into the second port (closest to the dipswitches) on the Neo
Gateway. Connect the other end of this cable into the HD Radio tuner. Connect the
factory antenna cable into the antenna connection on the HD Radio tuner (HDRT).
6. Plug the male connectors on the harness into the ports on the back of the radio. Next,
connect the factory harnesses into the female connectors on the harness. Be sure to
make a firm connection but do not force it. Plug the black micro-fit 24-pin connector on
the harness into the Neo Gateway box.
3
7. To complete the installation secure the Neo Gateway () and HD Radio tuner (HDRT)
into the cavity in the dash behind the radio. Be sure that the cables and interface modules
are not near moving parts or sharp metal edges as they may damage the cables. To
prevent rattling noises inside the dash, use zip ties, or electrical tape, or other fasteners
to mount the interfaces to the factory wiring or installed audio components (for example
under the factory Satellite tuner (if present).
8. With all connections made, reconnect the vehicle’s battery, insert the key into the
ignition, and turn the vehicle on. Check for proper operation of the Neo Gateway and
HD Radio tuner before reinstalling the factory dash panels.
9. NOTE: The first time that you access the Gateway, your radio may display “DEV INIT”
while the device is initializing. If this is displayed, please wait one minute then cycle the
ignition off and on. Access “SAT” mode again to begin normal gateway operation.
6. iPod Operation
Press the XM button to cycle through the Neo Gateway sources until “iPod” is displayed.
Each time you press the XM button you will switch to the next Neo Gateway source.
(Sat 1*, Sat 2*, Sat 3*, HD-FM1*, HD-FM2*, HD-FM3*, HD-AM*, iPod, Aux audio input)
* if equipped
Controls:
Next Track
Press the ”SEEK /\” button or turn the tune knob clockwise to advance one song in an
Album or Playlist.
Previous Track
Press the ”\/ SEEK” button or turn the tune knob counter-clockwise to move back one
song in an Album or Playlist.
Fast Forward
Press Preset #6 to Fast Forward the song that is playing. Press again to resume play.
Rewind
Press Preset #5 to Rewind the song that is playing. Press again to resume play.
Display Options
Press Preset #4 to switch between the song title information and the play counter. After
using the fast-forward or rewind function, the radio will display the elapsed time of the
song that is currently playing.
Enter Browse menu / make a selection
To enter the Browse menu, press preset #2. While in the Browse menu press preset #2
to select the option displayed on the radio.
Menu UP
Press Preset # 1 to move up one folder in the menu.
4
Exit Browse Menu
Press Preset #3 to exit the Browse menu and continue playing the current song.
Example of how to Browse by Artist
Press Preset #2 to enter the Browse menu.
”PL:LIST” will appear on the radio.
Press the ”SEEK /\” or ”\/ SEEK” button until “AR:ARTIST” is displayed.
Press Preset #2 to select Browse by Artist.
The list of Artists on your iPod will be displayed one at a time in alphabetical order. “AR:”
will be displayed in front of the artist’s name to indicate that you are searching for an
artist.
Press the ”SEEK /\” button to cycle through the artists.
Press Preset #2 to select the artist and display the albums by that artist.
The Albums from the selected Artist will be displayed one at a time in alphabetical order.
“AL:” will be displayed in front of the name of the album to indicate you are searching
for an album.
Press the ”SEEK /\” button to cycle through the albums.
Once the desired album is displayed,
Press Preset #2 to select the desired Album.
The first song in the album will be displayed. “TR:” will be displayed in front of the song
title to indicate that a “track” or song title is being displayed.
Press the ”SEEK /\” button to cycle through the songs in the selected album.
Songs are listed in the order in which they appear in the album, not alphabetically. Once
the radio displays the name of the desired song,
Press Preset #2 to select and play the desired song.
The display will automatically change to display the title of the chosen song.
7. HD Radio Operation
Press the XM button to cycle through the Neo Gateway sources until “HD FM” or “HD
AM” is displayed. Each time you press the XM button you will switch to the next Neo
Gateway source. (Sat 1*, Sat 2*, Sat 3*, HD-FM1*, HD-FM2*, HD-FM3*, HD-AM*, iPod,
Aux audio input) * if equipped
Tune Up / Seek Up
Press the ”SEEK /\” button to advance one station or to seek up to next broadcasting
station.
Tune Down / Seek Down
Press the ”\/ SEEK” button to move back one station or to seek down to the next
broadcasting station.
Storing Radio Stations into Preset Memory
Once you have tuned to a station you wish to store as a preset, press and hold one of
the Preset buttons (1-6) for longer than two seconds to store it into that location. The
screen will display “PR SAVED” and your preset has been stored into memory.
Recall Stored Preset Stations
Press the Preset button(1-6) that represents the station stored in memory that you wish
to recall.
5
Displaying Text
1. Press the info button on the radio to display artist/song title information, if available.
Not all stations broadcast the artist and song title information.
NOTE:
If the selected station is available in High Definition and the signal is strong enough the
radio will auto-lock onto the HD Radio Station. The letters “HD1, HD2 or HD3” will follow
the stations frequency when locked onto an HD station. The HD Radio Tuner will pick
up both digital and analog radio signals. Multicast HD2 and HD3 stations are digital only,
and will not be available if the radio signal is too far away, causing a weak reception.
8. Selecting AUX Input
Press the XM button to cycle through the Neo Gateway sources until “AUX” is displayed.
Each time you press the XM button you will switch to the next Neo Gateway source.
(Sat 1*, Sat 2*, Sat 3*, HD-FM1*, HD-FM2*, HD-FM3*, HD-AM*, iPod, Aux audio input)
* if equipped.
9. Selecting Factory Installed XM Radio
Press the XM button to cycle through the Neo Gateway sources until “SAT” is displayed.
Each time you press the XM button you will switch to the next Neo Gateway source.
(Sat 1*, Sat 2*, Sat 3*, HD-FM1*, HD-FM2*, HD-FM3*, HD-AM*, iPod, Aux audio input)
* if equipped.
For instructions on the operation of the factory installed Satellite Radio tuner, please
reference the owner’s manual supplied with the vehicle.
6
10. Troubleshooting
Symptom
Cause
Remedy
Radio shows iPod
not connected
iPod cable is not
Verify the docking cable is connected
connected to iPod or to the Neo Gateway, and the iPod
Gateway.
I can not correctly
control the iPod
through the radio.
The iPod firmware
may be out of date.
Update iPod firmware for free at http://
www.apple.com/ipod/download
I have updated my
iPod’s firmware
and still have
control issues
Sometimes the
iPods needs to be
reset
Press and hold the click wheel (center
button) and the menu button for 10
seconds. This will reboot the iPod.
YOU WILL NOT LOSE MUSIC on the
iPod by doing this reset
I don’t see iPod
artist or song
information on the
screen
The radio is
Press the Text / Scan button to see
displaying a different text
text field
I can’t use my
iPod’s click wheel
to select music
The iPod is in
external control
mode. This allows
text to be displayed
on the radio screen
Press the Aux / Sat button and select
AUX 2 source to control the iPod
manually using the click wheel
The Neo Gateway
does not recognize
the HD Radio
tuner (HDRT)
The HD tuner
was not properly
connected when the
was first connected
and initialized.
HDRT must be connected before
the is powered on. Disconnect
the from the vehicles harness for 5
minutes. Verify the 8 pin DIN HDRT
cable is securely connected at both
ends before reconnecting the vehicle
harness.
Radio shows “DEV
INIT”
Gateway device is
initializing
This only occurs the first time the is
powered on. Wait a few minutes, cycle
ignition off and on then enter SAT
Mode.
When I listen to
the factory AM or
FM radio there
is only static, no
audio.
Factory antenna
cable is connected
to the HD Radio
tuner.
Use Gateway to access HD Radio
source. This will provide all AM and
FM reception for your vehicle.
No AM or FM
Factory antenna
reception using the cable is not
HD Radio source
connected to the HD
Radio tuner (HDRT)
Remove from factory radio, connect
into HDRT module. Note* some
vehicles need to use the supplied
antenna adaptor to make this
connection.
HD Radio station
quality fluctuates
or is lost randomly
This is expected performance. The
Digital HD Radio playback will resume
in areas of higher broadcast signal
strength.
The HD Tuner is
temporarily losing
reception of the
Digital HD Radio
broadcast signal
7
11. Warranty
One Year Limited Warranty
The quality controls used in the manufacture of this product will ensure your
satisfaction. This warranty applies only to the original purchaser of this product
from an authorized dealer. This warranty covers any supplied or manufactured
parts of this product that, upon inspection by authorized personnel, is found to
have failed in normal use due to defects in material or workmanship. This warranty
does not apply to installation expenses. Attempting to service or modify this unit,
operating this unit under conditions other than the recommended voltage will render this
WARRANTY VOID.
Unless otherwise prescribed by law, shall not be liable for any personal injury,
property damage and or any incidental or consequential damages of any kind
(including water damage) resulting from malfunctions, defects, misuse, improper
installation or alteration of this product. All parts of this product are guaranteed
for a period of 1 year as follows:
Within the first 12 months from date of purchase, subject to the conditions above,
will repair or replace the product at their discretion, if it is defective in material or
workmanship providing it is returned to an Authorized Neo Car Audio dealer, with
PROOF OF PURCHASE from an authorized dealer.
Warning:
This equipment may be reset by unintentional electrostatic discharge during
operation. Exposure to direct sunlight or extreme heat may cause damage or
malfunction.
FCC Class B Radio Frequency
Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1. Re-orientate or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that of which the receiver is connected.
4. Consult the dealer or an experienced radio / television technical for help.
Notice : The changes or modifications not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
8
Notes
____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
9
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement