Verizon HMC Deadbolt Manual

Verizon HMC Deadbolt Manual
Keypad Deadbolt
2
If your door does not match the dimensions shown, go to
http://verizon.schlage.com for instructions on how to prepare
your door.
Installation Instructions
Model BE369
P516-406
Important Information
You will need
this code
information to
perform certain
functions using
the lock keypad.
These are the
factory default
lock code
settings (see
Step 1).
Door Edge
Door Edge
Phillips
six (6) digits
2³⁄₈” (60 mm)
OR
2³⁄₄” (70 mm)
OR
User Code A
Choose Faceplate
Choose the faceplate that most matches your existing door
preparation. To use the round faceplate, first remove the
rectangular faceplate and back plate. Then attach the round
faceplate.
Tools Needed
Lock Programming Code
four (4) digits
4
Check Door Dimensions
User Code B
2¹⁄₈” (53 mm)
Hole
Web Support:
http://monitoringcontrol.verizon.com
four (4) digits
OR
No change necessary.
5¹⁄₂” (140 mm)
Minimum
Package Contents
Top Cover
Screw
Alternate Faceplate
Cover
3
AA Batteries (3)
Bottom Cover
Screw
9V Battery
Check Backset
The backset is the distance from the edge of the door to the
center of the hole through which the lock is installed. This lock
will fit either a 2³⁄₈” backset or a 2³⁄₄” backset. The bolt is preset
to fit a 2³⁄₈” backset. If your backset is not 2³⁄₈”, you need to
adjust your bolt by rotating it counterclockwise.
Baseplate
2³⁄₈” (60 mm)
Baseplate Screws (2)
2³⁄₄” (70 mm)
5
OR
Install Bolt
The word “TOP” should be facing upward as shown below.
Keypad
Top
Top
Strike
Key
Bolt
Reinforcement Screws (2)
Reinforcement Plate
1
OR
2 ³⁄₄
Latch/Strike
Screws (4)
4
Locate Programming Code and Preset User Codes
Please go to http://monitoringcontrol.
verizon.com and follow the simple steps
provided in the online setup wizard. This will
enable you to add your Door Lock device to the
Home Monitoring and Control Network.
(2)
Programming Code XXXXXX
User Code A xxxx S/N x-xxxxxxxx
User Code B xxxx Model BE369
Programming Code XXXXXX
User Code A xxxx S/N x-xxxxxxxx
User Code B xxxx Model BE369
The programming code and the preset user
codes are printed on the yellow stickers
located on the back of the keypad and/or on
the installation sheet that came in the box.
Write these codes in the space provided at the
top of the page.
Latch/Strike Screws
6
9
Install the Keypad
Feed the cable over the top of the bolt assembly as shown
below. Then slide the tailpiece through the correct hole as
shown below.
12 Install the Cover
Secure the Baseplate to Door
Use the two screws shown to secure the baseplate to the door.
(2)
15 Check Operation
Place the cover against the door and secure using the two
screws. You may need to rotate the thumbturn to the proper
position, shown below. Note that the top screw is longer and
painted black.
Extend bolt (lock)
7
Locate the cam on the baseplate. This cam has a small arrow
on it that should point to the arrow that is printed on the casing
above the cam, like picture “a” below. If the cam is oriented
sideways, like the picture “b”, rotate the cam until the arrows
match.
Bottom Cover
Screw
10 Connect the Cable
Snap the connectors together. Tuck them into the open space
in the baseplate. Make sure no wires will be pinched when the
cover is installed.
Retract bolt (unlock)
13 Prepare the Frame for the Strike
Mark the 4 hole locations. Drill them as shown.
If the strike cut-out has not been prepared in the frame, see the
“Strike cut-out specifications” box.
a
b
!
8
No. Lock is
not installed
correctly.
Remove lock
and reinstall.
Pay close
attention to
cam position
in step 7.
Thumbturn
Baseplate Screws
Check the Cam on the Baseplate
1. Press the
Schlage
button.
2. Rotate
thumbturn
towards
door edge.
Top Cover
Screw
Tailpiece
Yes. Lock is
installed
correctly.
Check with
door open!
Tuck wires into open space
on baseplate. Be careful not
to pinch any wires between
cover and baseplate.
!
Did bolt extend?
Match arrows
⁵⁄₃₂” x 3”
(4 mm x 76 mm)
2 Holes
Did bolt retract?
Yes. Lock is
installed
correctly.
a. Find User
Code A
(written on
the first
page, see
step 1.)
b. Enter User
Code A
(four digits)
into the
keypad.
No. Lock is not
installed correctly.
Remove lock and
reinstall. Pay close
attention to
cam position
in step 7.
c. Rotate thumbturn away
from door edge.
Install the Baseplate
Feed the cable through the hole as shown below. DO NOT
connect the cable at this time. Then slide the baseplate onto
the tailpiece and press against the door. The baseplate should
stay in place.
14 Install the Strike
11 Install the Batteries
There are two sets of batteries. Install both the 9V and the AA
batteries.
2³⁄₄”
(69 mm)
1"
(25 mm)
b
Remove screw here to
access AA battery tray.
(2)
Strike cut-out specifications
(not to scale)
Reinforcement
Screws
1"
(25 mm)
(2)
c
After you finish the door lock installation, please go back to
the setup wizard at http://monitoringcontrol.verizon.com to
complete the configuration process.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Install for maximum security.
2³⁄₄"
(70 mm)
1¹⁄₂"
(38 mm)
16 Configure your system
Changes or modifications to this equipment not expressly approved
by Schlage could void the user’s authority to operate the equipment.
FCC ID: P2GBE369
IC: 7654A-BE369
¹⁄₈" (3 mm)
1¹⁄₈"
(29 mm)
Latch/Strike
Screws
©2011 Schlage Lock Company
P516-406 Rev. 03/11-5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement