Dulcotest
6.1
6.0 DULCOTEST® Sensor Technology
Table of Contents
SECTION 6 DULCOTEST® SENSOR TECHNOLOGY
6.0
6.1
6.2
6.3
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
Dulcotest® PT100 Temperature Sensor .........................................................…….......
Dulcotest® PHER, PHEN and pH Combination Probes ...................................….……
Dulcotest® CLB 2-µA Chlorine Sensor for use ONLY with Compact Controller ....…..
Dulcotest® Amperometric Sensors ...................................................………................
Dulcotest® Chlorine Sensors
6.3.1 Sensors for free Chlorine CLE 3-mA ..................................................................
6.3.1 Sensors for free Chlorine CLE 3.1-mA ...............................................................
6.3.2 Sensors for free Chlorine CLE 3-CAN ................................................................
6.3.2 Sensors for free Chlorine CLE 3.1-CAN .............................................................
6.3.3 Sensors for free Chlorine CLO 1-mA ..................................................................
6.3.3 Sensors for free Chlorine CLO 2-mA ..................................................................
6.3.3 Sensors for free Chlorine CLR 1-mA ..................................................................
6.3.4 Sensors for free Chlorine CLE 3-DMT ................................................................
6.3.4 Sensors for total Chlorine CTE 1-DMT ...............................................................
6.3.5 Sensors for total Chlorine CTE 1-CAN ...............................................................
6.3.5 Sensors for total Chlorine CGE 2-CAN ...............................................................
6.3.6 Sensors for free Chlorine CGE 2-mA ..................................................................
6.3.6 Sensors for free Chlorine CGE 2-CAN ...............................................................
Dulcotest® Sensors for Bromine BCR 1-mA .........................………............................
Dulcotest® Sensors for Bromine CBR1-mA .........................………............................
Dulcotest® Sensors for Bromine BRE 3-CAN .......................………............................
Dulcotest® Chlorine Dioxide Sensors
6.5.1 Dulcotest® Sensors for Chlorine Dioxide CDE 2-mA .....……….........................
6.5.1 Dulcotest® Sensors for Chlorine Dioxide CDP 1-mA 2ppm ..….........................
6.5.2 Dulcotest® Sensors for Chlorine Dioxide CDR 1-mA .....……….........................
6.5.2 Dulcotest® Sensors for Chlorine Dioxide CDR 1-CAN ...……….........................
Dulcotest® Ozone Sensor OZE 3-mA .............................................…..................……
Dulcotest® PAA Sensor PAA 1-mA ..................................................…..................……
Dulcotest® PER Sensor PER 1-mA ..................................................…..................……
Dulcotest® DO Sensor DO 1-mA ..................................................…..................…..…
6.8.2 Dulcotest® DO Sensor DO 2-mA .........................................…..................…..…
Dulcotest® Conductivity Sensors & Assessories - Electrolyte & Membrane Caps
6.9.1 Conductivity Sensors LF1 DE .............................................................................
6.9.2 Inductive Conductivity Sensors ICT 1 .................................................................
6.9.3 Inductive Conductivity Sensors ICT 2 .................................................................
Accessories Electrolyte & Membrane Caps .................................................................
Dulcotest® Modular In-line Probe Housing DGM
6.11.1
Identity Code Ordering System for In-Line Probe Housing Modules ...........
Cables, connectors, glands and cable assemblies .....................................................
6.2
6.3
6.4
6.5
6.6
6.6
6.7
6.7
6.8
6.8
6.8
6.9
6.9
6.10
6.10
6.11
6.11
6.12
6.12
6.13
6.14
6.14
6.15
6.15
6.16
6.17
6.17
6.18
6.19
6.20
6.21
6.22
6.23
6.25
6.26
ProMinent®
Revised: 1st January 2015
ProMinent®
6.2
Revised: 1st January 2015
6.0 DULCOTEST ® Sensor Technology pH
Measurement Probes & Resistance Thermometers
All probes are combination probes that
have been proven in both indu­st­ rial and
laboratory applications.
Before being dispatched all probes
are tested twice to ensure they are
functioning correctly; the first time
­
imme­dia­tely after being manufactured,
the second time about a fortnight
­afterwards in order to eli­m­inate glassspecific manufacturing risks.
All pH combination probes have their
voltage zero at pH 7 ± 0.5.
In the reference electrode system of the
ProMinent® pH and Redox combination
probes an Ag/AgCl conduc­
tance is
generally used which is not only less
harmful to the environment than the
calomel type (mercurous ­chloride) but
♦
♦
♦
can also be used in a ­wider temperature
application range.
The shaft diameter of all probes is 12
mm. All dimensions specified are
­approximate since pH and Redox p
­ robes
are handmade.
Please note:
The service life and storage life of all pH
and Redox electrodes is limited which is
why they should only be kept in storage
for as short as possible.
The electrodes must be stored solely with
the plugged on wetting caps in 3-molar
potassium chloride solution. They may
not be stored dry on any ­account!
The ageing of electrodes depends greatly
on the application conditions.
The service life is between one
and three years for problem-free
applica­
tions as well as at room
temperature and average pH values. In
extreme operating temperatures only
two to three months. Every electrode
ages even when it is not in operation!
Various influences can shorten the
service life of electrodes, e.g. chemical
­reactions with the reference electrode
or in the diaphragm, extreme pH values,
high temperatures, abrasive media or
media containing hydrofluoric acid.
From the date of delivery a 6
month warranty for material and
workman­ship is granted for all pH and
Redox electrodes.
Pt 100 with Push-and-Twist Connector for Type SN 6 Coax Connector
pH Combination Probes with Push-and-Twist Connector for Type SN 6 Coax Connector
Redox Combination Probes with Push-and-Twist Connector for Type SN 6 Coax Connector
For all other pH & Redox Probes and associated
equipment see the appropriate section in the
'Green Page' Price List
Temperature Sensor
120 ±3 mm
Type PT 100 SE
Resistance temperature sensor PT 100, integrated in glass stem, installed
length 120 mm; with plug-type head for SN6 coaxial connector and internal
thread PG 13.5
Temperature range: 0... 100ºC.
Operating pressure: max. 10 bar.
Typical applications:
Temperature measurement and
pH-temperature compensation.
305063.
Note: Local alternative also available
pk_5_034
6.3
ProMinent®
Revised: 1st January 2015
6.1 DULCOTEST® pH Probes
6.1 pH Probes with Push-and-Twist Type SN6 Coax Connectors
120 ±3 mm
PHER 112 SE
pH range: 1...12
Temperature: 0...80 °C
Max. pressure: 6 bar
Min. conductivity: >50 µS/cm
Electrolyte with solid KCl supply (salt rings in the reference electrolyte)
Diaphragm: PTFE ring diaphragm
Installation Length: 120 ±3 mm
Typical applications: Municipal and industrial wastewater, process water,
water in the chemical and paper manufacturing industries.
General, for water with suspended solid content.
1001586.
pk_6_018
PHEN 112 SE 3D
pH range: 1...12
Temperature: 0...80 °C
Max. pressure: Atmospheric pressure
Min. conductivity: >50 µS/cm
KCl electrolyte, refillable
Diaphragm: 3 Ceramic diaphragms
Installation Length: 120 ±3 mm
Typical applications: Waste water
Note: Supplied without storage container and tubing
150078.
Accessories
PE storage container and tubing305058.
KCl solution 3 molar 250ml.
KCl solution 3 molar 1000ml.
Note:
791440.
791441.
See Green Pages Price List for POOL Probes
and industrial probes.
pH-Combination Probes With Fixed Cable
PHEKT 013 F for Portamess® manual measuring devices
Plastic shaft electrode with inbuilt Pt 1000 for temperature display and compensation,
1 m fixed cable, device side DIN and banana plug.
pH range: 0…13
Temperature: 0…80 ºC
Max. pressure: atmospheric pressure
Min. conductivity: >150 µS/cm
Diaphragm: fibreglass
Length: 110 mm ± 3 mm
Device plug: DIN plug/banana plug
110 ±3
pk_6_008
Part No.
PHEKT 013 F ex HD works
1036537.
ProMinent®
6.4
Revised: 1st January 2015
6.2 DULCOTEST® pH & Redox Probes
6.2 pH Probes with Push-and-Twist Type SN6 Coax Connectors
ProMinent Code
PFC Part No
Note: See Green Pages Price List for POOL Probes and alternative
Industrial probes.
RHEP-Au-SE
Gold pin electrode
120 mm ± 3
Temperature: 0…80 ºC
Max. pressure: 6 bar
Min. conductivity: >150 µS/cm
Diaphragm: ceramic
Installation length: 120 mm ± 3 mm
Mounting hole minimum 14.5 dia. mm
Typical applications: Cyanide detoxification, ozone monitoring, saltwater pools or for use with
salwater generator. Do not use with media containing chlorine.
Part No.
RHEP-Au-SE ex HD works
1003875.
pk_6_035
Sensor for Chlorine, ONLY for use with Compact Controller
CLB 2-µA
Measured variable
Measuring range
120 ±3 mm
free chlorine (hypochlorous acid HOCI)
0.05 - 5.0 mg/l: linear, can be used for shock chlorination
up to 10.0 mg/l
Reference methodDPD1
pH range
5.0 … 9.0
Temperature
5 … 45 °C
Max. pressure
3.0 bar
Intake flow
30…60 l/h (in DGMA), constant flow needed as
flow-dependent signal
Power supply
Output signal
Temperature compensation
Typical applications
Measurement and control
equipment
In-line probe fitting
Measuring principle
16...24 V DC (2-wire)
Non-amplified primary current signal, not temperaturecompensated, uncalibrated, not electrically isolated
Pt 1000, integrated, calculation in the compact controller
Swimming pool, drinking water, can also be used with membrane-free chlorine production electrolysis processes, even with varying media temperatures
Measuring range
CLB 2-µA-5 ppm
Compact controller
DGM, DLG III
amperometric, 3 electrodes, no diaphragm
1038902
6.3
6.5
ProMinent®
Revised: 1st January 2015
6.3 DULCOTEST ® Amperometric Sensors
Amperometric Sensors for Chlorine, Bromine, Chlorine Dioxide, Chlorite, Ozone,
Disolved Oxygen and Peracetic Acid
For optimum functioning of chlorine, bromine, chlorine dioxide and ozone measuring cells
please note the following guidelines:
• Use DULCOMETER® measurement and control systems.
• Install only in ProMinent® DGM or DLGA in-line probe housings.
• Defined flow between 30 and 60 l/h.
• Chlorine measurement must only take place when pH is stable (CLE 3).
• Regular calibration with a Photometer (e.g. Type DT 1).
Important:
Amperometric probes are NOT electrically isolated.
When installing in external appliances (e.g.PLC), you should electrically isolate the supply
voltage and the analogue input signal.
• Summary of features:
• High zero point stability
• Compact design
• Integrated temperature correction
• Simple to install
• Simple to maintain
• Short warm up period time
• Measurement signal virtually unaffected by flow
Chlorine dissolved in water is present in different forms:
Free (active) chlorine:Cl2, HOCl (hypochlorous acid), OCl- (hypochlorite) recommended
sensors: CLE (analysis: DPD 1).
Combined chlorine:
Organic combined chlorine: mono, di, trichloramine (analysis: DPD 4 - DPD 1).
Of isocyanuric acid / isocyanurate bound chlorine (total available
chlorine) and the resulting free (effective) chlorine; recommended
sensor: CGE (analysis: DPD 1).
Total chlorine:
Sum of free and combined chlorine; recommended sensor: CTE
(analysis: DPD 4).
Applications:
Chlorine measurement in drinking, swimming pool, process,
industrial water and water of similar quality e.g. seawater/brine
with up to 15 % chloride content.
We recommend the CGE, CTE chlorine sensors for measuring
chlorine if pH value is high (8...9.5).
Guidelines for device
usage:
The measuring cells type CLE cannot be used in the presence
of iso-cyanuric acid/chlorine stabilisers!
The sensors with the suffix -mA are used with the measurement
and control devices D1C, D2C and DULCOMARIN®. The sensors with the suffix -4P are used with the earlier WS controllers
and for metering pumps with integrated chlorine controllers.
DMT-type sensors are used for the DMT transducer. CAN-type
sensors are used with the DULCOMARIN® II swimming pool
controller.
Note CLE sensors: The CLE type sensors cannot be used in liquids
containing isocyanu-ric acid/chlorine stabilisers.
ProMinent®
6.6
Revised: 1st January 2015
6.3 DULCOTEST® Sensors for Chlorine
6.3.1 DULCOTEST ®Sensors for free chlorine - CLE 3-mA and CLE 3.1-mA
Measurement of free chlorine
CLE 3-mA
Ø 25
221
Measured variable:
Free chlorine (hypochlorus acid HOCl)
Analysis:
DPD 1
Measurement range:
0.01... 50 mg/l
pH range:
5.5…8.0 (up to pH 8.5 for pH correction in the D1C)
Temperature range:
5…45 °C (temperature compensated)
Max. pressure:
1 bar
Flow:
30…60 l/h (in DGM or DLGA)
Power supply:
16…24 VDC (two-wire technology)
Output signal:
4…20 mA ³ measurement range (un-calibrated)
Warning: no electrical isolation!
Typical applications:
CLE 3-mA-0.5 ppm, potable water
CLE 3-mA-2.0/10 ppm, swimming pool, potable, industrial, process water (surfactant free)
Measurement and
control devices:
D1C, D2C, DULCOMARIN® (2/10 ppm only)
In-line probe housing:
DGM, DLGA
CLE 3-mA-0.5 ppm set, with 100 ml electrolyte *** not stocked***
CLE 3-mA-2 ppm set, with 100 ml electrolyte
pk_5_046
*** not stocked***
CLE 3-mA-5 ppm set, with 100 ml electrolyte
792920.
1033392.
CLE 3-mA-10 ppm set, with 100 ml electrolyte
792919.
CLE 3-mA-20 ppm set, with 100 ml electrolyte
1002964.
CLE 3-mA-50 ppm set, with 100 ml electrolyte
1020531.
CLE 3-mA-100 ppm set, with 100 ml electrolyte
1022786.
CLE 3.1-mA
Ø 25
221
Measured variable:
Free chlorine (hypochlorus acid HOCl) where there is a high
rate of combined chlorine and/or in the case of pH values
up to 8.5 (with D1C pH correction).
Analysis:
DPD 1
Measurement range:
0.02...2.00 mg/l (CLE 3.1-mA-2 ppm)
0.01...5.0 mg/l (CLE 3.1-mA-5 ppm)
0.1...10.0 mg/l (CLE 3.1-mA-10 ppm)
pH range:
5.5…8.0 (up to pH 8.5 for pH correction in the D1C)
Temperature range:
5…45 °C (temperature compensated)
Max. pressure:
1 bar
Flow:
30…60 l/h (in DGM or DLGA)
Power supply:
16…24 VDC (two-wire technology)
Output signal:
4…20 mA ³ measurement range (un-calibrated)
Warning: no electrical isolation!
Typical applications:
CLE 3-mA-2.0/10 ppm, swimming pool, potable, industrial, process water (surfactant free)
Measurement and
control devices:
pk_5_046
792927.
In-line probe housing:
D1C, D2C, DULCOMARIN®
DGM, DLGA
CLE 3.1-mA-0.5 ppm set, with 100 ml electrolyte
1020530.
CLE 3.1-mA-2 ppm set, with 100 ml electrolyte
1018369.
CLE 3.1-mA-5 ppm set, with 100 ml electrolyte
1019398.
CLE 3.1-mA-10 ppm set, with 100 ml electrolyte
1018368.
6.7
ProMinent®
Revised: 1st January 2015
6.3 DULCOTEST® Sensors for Chlorine
6.3.2 DULCOTEST ®Sensors for free chlorine - CLE 3-mA and CLE 3.1-mA
CLE 3-CAN
Ø 25
253
Measured variable:
Free chlorine (hypochlorus acid HOCl)
Analysis:
DPD 1
pH range:
5.5…8.0
Temperature range:
5…45 °C (temperature compensated)
Max. pressure:
1 bar
Flow:
30…60 l/h (in DGM or DLGA)
Power supply:
Via CAN interfaace(11-30V)
Output signal:
un-calibrated, temperature compensated, electrically isolated
Typical applications:
swimming pool, potable water (surfactant free)
Measurement and
control devices:
DULCOMARIN®
In-line probe housing:
DGM, DLGA
CLE 3-CAN-10 ppm
0.01 ... 10.0 mg/l
1023425.
complete with 100 ml electrolyte
pk_6_096
Ø 25
CLE 3.1-CAN
253
Measured variable:
Free chlorine (hypochlorus acid HOCl) with large proportions of
bound chlorine; to detect bound chlorine using DULCOMARIN®
II and Sensor for Total Chlorine type CTE 1-CAN
Reference Method:
DPD 1
pH range:
5.5…8.0 (up to pH 8.5 for pH correction in the D1C)
Temperature range:
5…45 °C (temperature compensated)
Max. pressure:
1 bar
Flow:
30…60 l/h (in DGM or DLGA)
Power supply:
Via CAN interface (11-30V)
Output signal:
un-calibrated, temperature compensated, electrically isolated
Typical applications:
swimming pool, potable water with a high percentage of bound
chlorine (surfactant free)
Measurement and
control devices:
DULCOMARIN® II
In-line probe housing:
DGM, DLGA
CLE 3.1-CAN-10 ppm 0.01 ... 10.0 mg/l
complete with 100 ml electrolyte
pk_6_096
1023426.
ProMinent®
6.8
Revised: 1st January 2015
6.3 DULCOTEST ® Sensors for Chlorine
6.3.3
DULCOTEST ® Sensors for Free Chlorine
CLO 1-mA
Measured variable
free chlorine (hypochlorus acid HOCl)
Reference method
DPD1
pH range
5,0 … 9,0
Temperature range
5 … 45 °C
Max. pressure
8,0 bar
Intake flow
30…60 l/h (in DGM or DLG III), constant flow as flow-
dependent signal
Power supply
16...24 V DC (2-wire)
Output signal
4…20 mA = Measuring range, temperature-compensated, uncalibrated, not electrically isolated
Typical applications
swimming pool, uncontaminated drinking water and
industrial service water, and can also be used together with diaphragm-free electrolysis
processes
Measurement and D1C, D2C, DULCOMARIN®
control equipment
In-line probe housing
DGM, DLG III to 60 °C, special fitting for 60 °C-70 °C
(on request)
Measuring principle
amperometric, 3 electrodes, no diaphragm
CLO 1-mA-2 ppm
CLO 1-mA-10 ppm
0,02…2,0 mg/l
0,10…10,0 mg/l
1033871
1033870
CLO 2-mA
Measured variable
free chlorine (hypochlorus acid HOCl)
Reference method
DPD1
pH range
5,0 … 9,0
Temperature range
5 … 70 °C
Max. pressure
8,0 bar
Intake flow
30…60 l/h (im DGM oder DLG III), constant flow as flow-
dependent signal
Power supply
16…24 V DC (two-wire system)
Output signal
4…20 mA = Measuring range, temperature-compensated, uncalibrated, not electrically isolated
Typical applications
Hot water up to 70°C, combating legionella uncontaminated drinking water and industrial service water, and can also be used together with
diaphragm-free electrolysis processes
Measurement and D1C, D2C, DULCOMARIN®
control equipment
In-line probe housing
DGM, DLG III to 60°C, special fitting for 60°C-70°C
(on request)
Measuring principle
amperometric, 3 electrodes, no diaphragm
CLO 2-mA-2 ppm
0,02…2,0 mg/l
1033878
Ø 25
CLR 1-mA-200ppm
221
Measured variable
Reference method
Temperature
Max. pressure
Intake flow
Power supply
Output signal
Typical applications
Measuring and control
equipment
In-line probe fitting
Measuring principle
pk_5_047_1
Free chlorine (hypochlorous acid HOCI)
DPD1pH range5.5 … 8.0
5 … 45 °C
1.0 bar
30…60 l/h (in DGM, DLG II)
16...24 V DC (2-wire)
4…20 mA = Measuring range, temperature-compensated, uncalibrated, not electrically isolated
Salad, vegetable and poultry washing water, contaminated process and waste water
D1Cb, DAC, delta® solenoid diaphragm metering pump
DGM, DLG III
amperometric, 2 electrodes, diaphragm-covered
CLR 1-mA-200 ppm
20.00 …200,0 mg/l
1047978
6.9
ProMinent®
Revised: 1st January 2015
6.3 DULCOTEST® Sensors for DMT
6.3.4 DULCOTEST ® Sensors for free Chlorine - CLE3-DMT and CTE1-DMT
CLE 3-DMT
Ø 25
173.1
pk_5_045
Measuring cell for use with the DMT “chlorine” measurement transducer.
Measured variable:
Free chlorine (hypochlorous acid HOCl)
Reference method:
DPD1
Measurement range:
0.01...5.0 mg/l
0.05...50 mg/l
Supply:
From the DMT measurement transducer (3.3 VDC)
Output signal:
Un-calibrated, not temperature compensated
Temperature
5…45 °C
Max. pressure:
1 bar
Flow:
measurement:
Measuring cell output:
Other data as for CLE-3 mA.
30…60 l/h (in DGM or DLGA)
Via integrated Pt 1000: compensation carried out in DMT
5-pin plug
CLE 3-DMT-5 ppm set with 100 ml electrolyte
1005511.
CLE 3-DMT-50 ppm set with 100 ml electrolyte
1005512.
See section 3.21
Universal control cable, 5-pole round connector, 5-wire, 2 m
Universal control cable, 5-pole round connector, 5-wire, 5 m
1001300.
1001301.
Universal control cable, 5-pole round connector, 5-wire, 10 m
1001302.
Ø 25
CTE 1-DMT
178
pk_5_022
Measuring cell for use with the DMT “chlorine” measurement transducer.
Measured variable:
Total Chlorine
Reference method:
DPD4
Measurement range:
0.01...10 mg/l
Supply:
From the DMT measurement transducer (3.3 VDC)
Output signal:
Un-calibrated, not temperature compensated
Temperature
5…45 °C
Max. pressure:
1 bar
Flow:
measurement:
Measuring cell output:
Other data as for CLE-3 mA.
30…60 l/h (in DGM or DLGA)
Via integrated Pt 1000: compensation carried out in DMT
5-pin plug
CTE 1-DMT-10 ppm set with 50 ml electrolyte
1007540.
See section 3.21
Universal control cable, 5-pole round connector, 5-wire, 2 m
Universal control cable, 5-pole round connector, 5-wire, 5 m
Universal control cable, 5-pole round connector, 5-wire, 10 m
1001300.
1001301.
1001302.
ProMinent®
6.10
Revised: 1st January 2015
6.3 DULCOTEST ® Sensors for Total Chlorine
6.3.5 DULCOTEST ® Sensors for Total Chlorine
Ø 25
Measured variable of total chlorine
CTE 1-mA
221
Measured variable:
total chlorine
Analysis:
DPD 4
Measurement range:
0.01…0.50 mg/l (CTE 1-mA-0.5 ppm)
0.02… 2.00 mg/l (CTE 1-mA-2 ppm)
0.05… 5.00 mg/l (CTE 1-mA-5 ppm)
0.1…10.0 mg/l (CTE 1-mA-10 ppm)
pH range:
5.5…9.5
Temperature range:
5…45 °C
Max. pressure:
3 bar
Flow:
30…60 l/h (in DGM or DLGA)
Power supply:
16…24 V DC (two-wire technology)
Output signal:
4…20 mA ³ measurement range (un-calibrated)
Warning: no electrical isolation!
Typical applications:
CTE 1-mA-0.5 ppm, potable water
CTE 1-mA-2/5/10 ppm, potable, industrial, process water,
In swimming pool in combination with CLE3.1 for determining
combined chlorine.
pk_5_047_1
Measurement and
control devices:
D1C, DULCOMARIN® (2/10 ppm only)
In-line probe housing:
DGM, DLGA
Part No.
CTE 1-mA-0.5 ppm set, with 50 ml electrolyte
740686.
CTE 1-mA-2 ppm set, with 50 ml electrolyte
740685.
CTE 1-mA-5 ppm set, with 50 ml electrolyte
1003203.
CTE 1-mA-10 ppm set, with 50 ml electrolyte
740684.
CTE 1-CAN
Ø 25
Measured variable:
total chlorine
Analysis:
DPD 4
pH range:
5.5…9.5
Temperature range:
5…45 °C
Max. pressure:
3 bar
Flow:
30…60 l/h (in DGM or DLGA)
Power supply:
Via CAN interface (11-30V)
Output signal:
un-calibrated, temperature compensated, electrically isolated
Typical applications:
In swimming pool in combination with CLE3.1 for determining
combined chlorine.
221
Measurement and
control devices:
DULCOMARIN® II
In-line probe housing:
DGM, DLGA
CTE 1-mA-10 ppm
0.01 ... 10.0 mg/l
Part No.
pk_6_084
1023427.
6.11
ProMinent®
Revised: 1st January 2015
6.3 DULCOTEST ® Sensors for Total Chlorine
6.3.6 DULCOTEST ® Sensors for total Chlorine
Ø 25
Measured variable of organic combined chlorine and
free chlorine (total available chlorine)
CGE 2-mA
221
pk_5_047_1
Measured variable:
Organic combined chlorine and free chlorine
(e.g. trichloroisocyanuric acid)
Analysis:
DPD 1
Measurement range:
0.02…2.00 mg/l (CGE 2-mA-2 ppm)
0.1…10.0 mg/l (CGE 2-mA-10 ppm)
pH range:
5.5…9.5
Temperature range:
5…45 °C (temperature compensated)
Max. pressure:
3 bar
Flow:
30…60 l/h (in DGM or DLGA)
Power supply:
16…24 V DC (two-wire technology)
Output signal:
4…20 mA ³ measurement range (un-calibrated)
Warning: no electrical isolation!
Typical applications:
Swimming pool, potable, industrial, process water, cooling water
and water with a high pH value
Measurement and
control devices:
D1C, D2C, DULCOMARIN®
In-line probe housing:
DGM, DLGA
Part No.
CGE 2-mA-2 ppm set, with 50 ml electrolyte
792843.
CGE 2-mA-10 ppm set, with 50 ml electrolyte
792842.
CGE 2-CAN
Ø 25
221
Measured variable:
Organic combined chlorine and free chlorine
(e.g. trichloroisocyanuric acid)
Analysis:
DPD 1
pH range:
5.5…9.5
Temperature range:
5…45 °C (temperature compensated)
Max. pressure:
3 bar
Flow:
30…60 l/h (in DGM or DLGA)
Power supply:
Via CAN interface (11-30V)
Output signal:
un-calibrated, temperature compensated, electrically isolated
Typical applications:
Swimming pool water
Measurement and
control devices:
DULCOMARIN® II
In-line probe housing:
DGM, DLGA
CGE 2-CAN-10 ppm
0.01 ... 10.0 mg/l
Part No.
with 50 ml electrolyte
pk_6_084
1024420.
ProMinent®
6.12
Revised: 1st January 2015
6.4 DULCOTEST ® Bromine Sensors
6.4.1
DULCOTEST ® Sensors for Bromine
The following bromating agents are used as disinfectants:
organic bromating agent
a) DBDMH (1.3-dibrom-5.5-dimethyl-hydantoin) e. g. sold as Albrom 100®
b) BCDMH (1-bromine-3-chlorine-5.5-dimethyl-hydantoin) e.g. sold as Brom-Sticks®
These bromating agents are solid and are metered as saturated solutions via brominators.
Inorganic free bromine
Free bromine is produced via the so-called Acti-Brom process® (Nalco) chlorine bleach + acid
+sodium bromide.
For measuring DBDMH or free bromine as a bromating agent in the measurement range: 0.2
-10 ppm bromine the BRE 2-mA-10 ppm sensor is recommended along with DPD1-method
calibration.
Alternatively, to measure BCDMH in the same measurement range, the BRE 1-mA-10 ppm
sensor is recommended along with DPD4-method calibration.
Typical applications are in swimming pools, Jacuzzis and cooling systems. Particularly in cooling
systems the quality of the sample water must be tested and, where applicable, compatibility
with other chemicals employed (e.g. corrosion inhibitors). Dissolved copper(>0.1 mg/l) will
interfere with the measurement.
Photometric DPD measurement is the recommended method for calibrating the bromine sensor
(e.g. with DT 1), calculated and displayed as bromine. If bromine is determined as “chlorine”
with DPD, note when selecting the measurement range that you need to lower the result by a
factor of 2.25.
BCR 1-mA (replaces earlier BRE1)
Ø 25
230
Measured variable:
Total available bromine from BCDMH(bromo-3-chloro-5.5-dimethythdantoin) and N-Bromanide sulphonate
Reference method:
DPD4
pH drange:
5.0 ... 9.5
Temperature range:
5 … 45 °C
Max. pressure:
1 bar
Sample flow:
30 … 60 l/h (in DGM or DLGA)
Voltage:
16 … 24 V DC (two-wire technology)
Output signal:
4 … 20 mA measurement range, temperature compensated
Warning: not electrically isolated!
Typical applications:
Cooling water, process water, waste water, water with higer pH
values (stable pH)
Measurement and
control device:
D1C, D2C, DAC
In-line probe housing: DGM, DLGA
pk_5_089
BCR 1-mA (replaces earlier BRE1)
Part no.
BCR 1-mA-0.5 ppm with 50 ml electrolyte
1041697.
BCR 1-mA-2 ppm with 50 ml electrolyte
1040115.
BCR 1-mA -10 ppm with 50 ml electrolyte
1041698.
Measurement range relates to BCDMH
6.13
ProMinent®
Revised: 1st January 2015
6.4 DULCOTEST ® Bromine Sensors
6.4.2
DULCOTEST ® Sensors for Bromine
CBR 1-mA (replaces earlier BRE2)
Ø 25
Measured variable:
Reference method:
pH range:
230
Free chlorine (hypochlorous acid HOCl),free bromine,
bound bromine
DPD1
5.0 ..... 9.5
Temperature
5 … 45 °C
Max. pressure:
1 bar
Flow:
30 … 60 l/h (in DGM or DLGA)
Power supply:
Supply:
Output signal:
Typical applications: Measurement
and control equipment:
In-line probe fitting
Measuring principle
16 ... 24 V DC (2-wire)
From the DMT measurement transducer (3.3 VDC)
4 ... 20 mA = Measuring range, temperature-compenstated,
uncalibrated, not electrically isolated
Cooling water, Process water, Waste water, Water with higher pH values (stable pH)
D1C, ProMcon
CBR 1-mA-0.5 ppm
0.01 ... 0.5 mg/l
1038016.
CBR 1-mA-2 ppm
0.02 ... 2.0 mg/l
1038015.
CBR 1-mA-10 ppm
0.10 ... 10.0 mg/l
1038014.
DGM, DLGA
amperometric, 2 electrodes, diaphragm-covered
pk_5_089
Note: the above measuring range is based on chlorine. The upper and lower limits of the
measuring range are increased by a factor of 2.25 when measuring bromine
e.g. CBR 1-mA-2 ppm = 4.5 ppm
BRE 3-CAN
Ø 25
Measured variable:
Total available bromine
Bromine chemicals:
DBDMH (1.3-dibromine 5.5-dimethyl hydantoin)
BCDMH (1-bromine-3-chlorine-5.5-dimethyl hydantoin),
free bromine
Reference method:
DBDMH, free bromine:DPD1
BCDMH:DPD4
221
Measurement range:
DBDMH free bromine:0.2...10.0 mg/l with type BRE 2-mA-10 ppm
BCDMH:0.2...10.0 mg/l with type BRE 1-mA-10 ppm
pH dependence:
if changes from pH 7 to pH 8 the sensor sensitivity is reduced
a) in the case of DBDMH and free bromine by approx. 10 %
b) in the case of BCDMH by approx. 25 %
Temperature range:
5…45 °C
Max. pressure:
3 bar
Sample flow:
30…60 l/h (in DGM or DLGA)
Voltage:
Via CAN interface (11-30V)
Output signal:
uncalibrated, temperature compensated, electically isolated
Typical applications:
Swimming pools / whirlpools and cooling water; can also be used
in seawater
Measurement and
control device:
Dulcomarin® II
In-line probe housing: DGM, DLGA
Part no.
pk_6_084
BRE 3-CAN-10ppm
0.02 ... 10.0 mg/l
1029660.
ProMinent®
6.14
Revised: 1st January 2015
6.5 DULCOTEST ® Chlorine Dioxide Sensors
6.5.1
DULCOTEST ® Sensors for Chlorine Dioxide
CDE 2-mA
Ø 25
221
pk_5_046
Measured variable
Reference method
pH range
Cross sensibility
Temperature range
Max. pressure
Intake flow
Supply voltage
Output signal
Typical applications
Measurement and control equipment
In-line probe housing
Measuring Principle
Chlorine dioxide (ClO2)
DPD1
4.0 … 11
Ozone, compared with chlorine <2%
1 … 45 °C
1,0 bar
30…60 l/h (in DGMA or DLG III)
16…24 V DC
4…20 mA temperature compensated, uncalibrated,
not electrically isolated
uncontaminated potable water (surfactant-free)
D1C, D2C, DAC
DGMa / DLG III
amperometric, 2 electrodes, diaphragm-covered
CDE 2-mA-0.5 ppm
CDE 2-mA-2 ppm
CDE 2-mA-10 ppm
with 100 ml of electrolyte
0,01…0,5 mg/l
0,02…2,0 mg/l
0,10…10,0 mg/l
792930.
792929.
792928.
Ø 25
C D P 1 - m A - 2 p p m ( C l O 2- p ro c e s s p ro b e )
Applications:
Bottle washing machines and water containing surfactants
Measured variable:
Chlorine dioxide (ClO2)
Analysis:
DPD 1
Measurement range:
0.02...2.00 mg/l
pH range:
5.5...10.5
Temperature range:
10...45 °C (short term periods 55 °C) with external temperature
correction via Pt 100 (no internal temperature correction!)
230
Temperature variation
speed:
Up to 10 K/min
Max. pressure:
3 bar (no pressure surges)
Flow:
30...60 l/h (in DGM or DGMA)
Supply voltage: 16...24 V DC (two-wire technology)
Output signal:
4...20 mA ³ measurement range (un-calibrated)
Warning: no electrical isolation!
pk_5_050
Type application:
Process water containing surfactants (bottle washing machines)
pk_5_081
Measuring and
control device:
D1C with automatic temperature compensation only
In line probe housing:
the following is recommended (see fig.)
Probe housing quote on request.
Part No.
CDP 1-mA-2 ppm set with 100 ml electrolyte
1002149
6.15
ProMinent®
Revised: 1st January 2015
6.5 DULCOTEST ® Chlorine Dioxide Sensors
6.5.2 DULCOTEST ® Sensors for Chlorine Dioxide
CDR 1-mA
Ø 25
223
Measured variable
Reference method
pH range
Temperature range
Max. pressure
Intake flow
Supply voltage
Output signal
Typical applications
Measurement and control equipment
In-line probe housing
Measuring Principle
Chlorine dioxide (ClO2)
DPD1
1.0 … 10
1 … 55 °C (short-term periods 60 °C)
310 bar (30 °C in DGMA)
30…60 l/h (in DGMA or DLG III)
16…24 V DC
4…20 mA temperature compensated, uncalibrated,
not electrically isolated
contaminated industrial, process water, containing surfactants,Cooling water, irrigation water,slightly
contaminated waste water, warm water
D1C
DGMa / DLG III
amperometric, 2 electrodes, diaphragm-covered
CDR 1-mA-0.5 ppm
CDR 1-mA-2 ppm
CDR 1-mA-10 ppm
0,01…0,5 mg/l
0,02…2,0 mg/l
0,10…10,0 mg/l
1033762
1033393
1033404
pk_6_083
CDR 1-CAN
Ø 25
259
Measured variable
Reference method
pH range
Temperature range
Max. pressure
Response time sensor
Intake flow
Supply voltage
Temperature measurement
Output signal
Typical applications
Measurement and control equipment
In-line probe housing
Measuring Principle
pk_6_084
Chlorine dioxide (ClO2)
DPD1
1.0 … 10
5 … 45 °C
1.0 bar (30 °C in DGMA)
t90~ 3 min.
30…60 l/h (in DGMA or DLG III)
Via CAN interface (11-30V)
via integral digital semiconductor device
uncalibrated, temperature-compensated,
electrically isolated
contaminated industrial, process water, containing surfactants,cooling water, irrigation water,slightly
contaminated waste water, warm water
Dulcomarin® Disinfection Controller
DGMa / DLG III
amperometric, 2 electrodes, diaphragm-covered
CDR 1-can-10 ppm
0,10…10,0 mg/l
1041145
ProMinent®
6.16
Revised: 1st January 2015
6.6 DULCOTEST ® Ozone Sensor
6.6.1 DULCOTEST ® Sensors for Ozone
Ø 25
OZE 3-mA
221
Measured variable:
Ozone (O3)
Analysis:
DPD 4
Measurement range:
0.02…2.00 mg/l
pH range:
Ozone stability range
Temperature range:
5…40 °C (temperature compensated), no significant
Temperature fluctuations
Max. pressure:
1 bar
Flow:
30…60 l/h (in DGM or DLGA)
Power supply:
16…24 VDC (two-wire technology)
Output signal:
4…20 mA ³ measurement range (un-calibrated)
Warning: no electrical isolation!
Typical applications:
Swimming pools, potable, industrial, process water, surfactant free
Measurement and
control devices:
D1C
In-line probe housing:
DGM , DLGA
Part No.
pk_5_046
OZE 3-mA-2 ppm set, with 100 ml electrolyte
OZE 3-mA-5 ppm set, with 100 ml electrolyte
792957.
*** NET
*** special *** not carried in stock, 6 week delivery
The DULCOTEST® PAA 1 sensor models are membrane-covered amperometric 2-electrode sensors for the selective
measurement of peracetic acid. Peracetic acid is used as a disinfectant particularly in the food and beverage industries as well as in the
cosmetic, pharmaceutical and medical industries. The continuous measurement and control of the peracetic acid is essential to comply
with demanding disinfection requirements and for quality control. Unlike with the sensors in the earlier Perox PES system the PAA 1-mA
can be used with the D1Ca controller. Commissioning and maintenance is greatly simplified
The sensors can even be used in the presence of surfactants (tensides).
The DULCOTEST® PEROX and PER1 sensors are membrane-covered, amperometric sensors for the online concentration
measurement of hydrogen peroxide. Due to its complete biodegradability, hydrogen peroxide is a disinfectant and oxidising agent
frequently used in water treatment and production:chemical bleach in the wood, paper, textile and mineral compounds industries,organic
synthesis in the chemical, pharmaceutical and cosmetics industries,oxidation of potable water, landfill seepage water, contaminated
ground water,disinfection of cooling, process and production water in the pharmaceutical, food and beverage industries as well as in
swimming pools,deodorisation (gas scrubbers) in municipal and industrial clarification plants,dechlorination in chemical processes
6.17
ProMinent®
Revised: 1st January 2015
6.7 DULCOTEST ® PAA Sensor
6.7.1 DULCOTEST ® Sensor for Peracetic Acid
PAA 1-mA
Ø 25
223
Measured variable:
Reference method:
Measurement range
pH range:
Temp. range:
Admissible
Temperature fluctuation:
Response time T90
Pressure.:
Intake flow:
Power supply
Output signal:
Typical application:
pk_6_083
peracetic acid
titration
10...200 mg/l (PAA 1-mA-200 ppm)
100...2000 mg/l (PAA 1-mA- 2000 ppm)
1...9 (peracetic acid stability range)
1...45 °C (temperature compensated)
0.3 °C/min
3 min. Max.
3 bar (30 °C, in DGM)
30- 60 l/h (with DGM or DLGA in-line probe housing)
16...24 V DC (two wire)
4...20 mA measurement range (uncalibrated)
Important not electrically isolated
scouring in Cleaning in Place (CIP) and rinsing
systems,also designed for use in the presence of cationic
andanionic tensides. Selective measurement of peracetic
acid as well as hydrogen peroxide is possible.
Measurement and control
equipment:D1C
In-line probe housing:
DGM, DLGA
PAA 1-mA-200ppm
PAA 1-mA-2000ppm
PER 1-mA
Ø 25
Measured variable:
Calibration:
pH range:
Temperature:
Admissible Temperature
Response time sensor
223
pk_6_083
1022506.
1022507.
Measuring accuracy
Min. conductivity
Max. pressure
Intake flow:
Power supply
Output signal:
Typical application:
Measurement and control
equipment:
In-line probe housing:
hydrogen peroxide
Photometric with manual DT3B photometer
2.5 ... 11.0
0 ... 50 °C
<0.3 °C/min
T90 approx. 480 sec.
P 1 ppm or better than E 5% of measured value
0.05 ... 5.00 mS/cm
1.0 bar
20 - 100 l/h (with DGM or DLGA in-line probe housing)
16...24 V DC (two wire)
4...20 mA measurement range (uncalibrated)
Important not electrically isolated
Swimming pools, treatment of contaminated waste waters,
treatment of process media from production
D1Cb, DAC
DGM, DLGA
PER 1-mA-200ppm
PER 1-mA-2000ppm
1022509.
1022510.
ProMinent®
6.18
Revised: 1st January 2015
6.8 DULCOTEST ® Dissolved Oxygen Sensors
6.8.1 Dissolved Oxygen Sensors
The measured variable “dissolved oxygen” gives the quantity of the gaseous physical
dissolved oxygen in its aqueous phase in mg/l (ppm).
The “dissolved oxygen” is thereby an important parameter for controlling the quality of
surface water and water which needs to be oxygenated for use in aqua culture and aqua
zoos. The dissolved oxygen is also used to control processes in sewage plants and waterworks.
The following sensors are assigned to the different applications and can be supplied separatelyas 4-20 mA-transmitters to central controllers or together with the D1C as a stand
alonesolution (measured variable: “dissolved oxygen”: X. s. chapter 5).
DO 1-mA
180
pk_6_050_1
50
Measured variable:
Calibration:
Measurement range:
Reproducibility of
measurement:
Temp. range:
Max. pressure:
Velocity of sample water:
Enclosure rating:
Power supply:
Electrical connection:
Output signal:
Process integration:
Typical applications
dissolved oxygen
of oxygen in air
2-20 mg/l
± 0.5 % of measurement limit value
0 -50 °C
1 bar
minimum: 0.05 m/s
IP 68
12...30 V DC
fixed lead, 10 m
4-20 mA. Measurement range calibrated, temperature
corrected and electrically isolated
a) immersion, suspended on cable with or without mountain
bracket for cable.
b) Immersion of immersion pipe
1. Immersion pipe with 50 mm outside diameter and1-1/4
inch internal thread (provided by the customer).Connection
via immersion pipe adapter
2. PVC immersion pipe with 50 mm outside diameter(provided
by the customer). Connection via standard PVCadhesive
union (provided by the customer).
c) In-flow operation to order
Fish and shrimp farming.
Conditioning of water in large aquariain zoological systems.
Control of oxygen input in waterworks
Appraisal of the biological status of surface waters
Part No.
DO 1-mA-20 ppm
1020532
pk_6_011
6.19
ProMinent®
Revised: 1st January 2015
6.8 DULCOTEST ® Dissolved Oxygen Sensors
6.8.2
Dissolved Oxygen Sensors
DO 2-mA
Measured variable:
Calibration:
Measurement range:
Reproducibility of
measurement:
Temp. Range:
Max. pressure:
Velocity of sample water:
Enclosure rating:
Supply voltage:
Electrical connection:
Output signal:
pk_6_051
260
dissolved oxygen
of oxygen in air
0.1-10 mg/l
± 0.5 % of measurement limit value
0 -50 °C
1 bar
minimum: 0.05 m/s
IP 68
12...30 V DC
fixed lead, 10 m
4-20 mA. Measurement range calibrated, temperature
corrected and electrically isolated Process integration: as float
with venturi grooves to increase the flow of samplewater for
the self-cleaning of the sensor part. Supplied with adapter for
connection to PVC-pipes with outside diameter 50mm, and
railing bracket, also for PVC pipes with outside diameter 50
mm.
Note: The customer must provide the straight PVC tube and a
45 ° standard elbow for gluing to PVC pipes (outside diameter
50 mm).
Typical application
Control of the oxygen input in activated sludge pools (sewage
plant) for the purpose of energy conservation.
Part No.
DO 2-mA-10 ppm
1020533
pk_6_012
Spare parts for dissolved oxygen sensors
A
Lmin. = A
-m
ax
V
V
Measuring
range
Sensor insert for DO 1-mA-20 ppm
Membrane thickness 125 µm, 0-20 mg/l 2.00…20.0 mg/l
1020534
Sensor insert for DO 2-mA-10 ppm
Membrane thickness 50 µm, 0-10 mg/0.10…10.0 mg/l
1020535
.=
4m
V
Vmin. = 0.05 m/s
ProMinent®
6.20
Revised: 1st January 2015
6.9 DULCOTEST® Conductivity Sensors
6.9.1
DULCOTEST ® Conductivity Sensors
Description/version
120 ±3
Part no.
Price
LF1 DE
Measuring range
0.01…20 mS/cm
Cell constant
k1 cm-1 ±5 %
Temperature compensation –
Fluid temperature
0…80 °C
Max. pressure
16.0 bar
Sensors
special graphite
Shaft material
Epoxy
Thread
PG 13.5
Fitting length
120 ± 3 mm
Electrical connection
DIN 4-pin angle plug
Typical applications
Potable, cooling, industrial water. Sensors of the LF series
have only limited applicability for taking measurements in
cleaning solutions containing surfactants and media containing
solvents.
LF1 DE
1001375.
Suitability: Compact Controller, DMTa, DICa
Ø 12
pk_6_086
* NOTE: if using this with a Compact Controller
a Shielded 4 wire cable MUST be used.
120 ±3
LFTK 1 DE
Measuring range
0.01…20 mS/cm
Cell constant
k1 cm-1 ±5 %
Temperature compensation Pt 1000
Fluid temperature
0…80 °C
Max. pressure
16.0 bar
Sensors
special graphite
Shaft material
Epoxy
Thread
PG 13.5
Fitting length
120 ± 3 mm
Electrical connection
DIN 4-pin angle plug
Typical applications
Potable, cooling, industrial water. Sensors of the LF series
have only limited applicability for taking measurements in
cleaning solutions containing surfactants and media containing
solvents.
Ø 12
pk_6_086
LFTK 1 DE
Suitability: Compact Controller
* NOTE: if using this with a Compact Controller
a Shielded 4 wire cable MUST be used.
1002822.
6.21
ProMinent®
Revised: 1st January 2015
6.9 DULCOTEST® Conductivity Sensors
6.8.2
Inductive Conductivity Sensors
INDUCTIVE CONDUCTIVE SENSORS
Electrode-free inductive conductivity sensors are used to measure the electrolytic conductivity over a wide measurement range in heavily soiled and/or aggressive media and offer
a particularly low maintenance operating method. The sensors are particularly suitable for
the measurement of high conductivity levels since there is no electrode polarisation.
ICT 1 and ICT 1-IMA-1m/ICT 1-IMA-2m
Economical inductive conductivity sensors for all soiled water types and for high conductivity levels up to a temperature of 70 °C. The ICT 1 sensor is designed for in-flow measurement and is installed in DN40 pipes (option PVC or PP). The ICT 1-IMA-1 m and ICT
1-IMA-2 m immersion sensors comprise the ICT 1-IM sensor and the ready-fitted IMA-ICT1
immersion pipe, length 1 m or 2 m.
Measurement range: 0.2-1000 mS/cm
Cell constant: 8.5 cm-1
Temperature
compensation: Pt 100
Medium temperature: 0 °C ... 70 °C
Max. pressure: 8 bar/40 °C, 1 bar/70 °C
Material: Sensor: PP, Seals: Viton®
Assembly:
ICT 1:
with union nuts, 2-1/4 imperial internal thread, DN40, PVC incl. DN40
58 d.
208
108
80 d.
2-1/4"
A
28 d.
150
155 min
70
50 d.
75 d.
pk_6_088
1110 & 2110
pk_6_087
Adhesive joints with 2-1/4 imperial external thread for installation in
DN40 standard PVC pipes included in scope of supply.
ICT 1-IMA-1m sensor: supplied with immersion pipe, 1 m
ICT 1-IMA-2m sensor: supplied with immersion pipe, 2 m
The assembly accessories for the IPHa 3-PP in-line probe housing (see 6.5.3) can be used
for both immersion sensors.
Power supply: all versions, 7 m fixed cable
Enclosure rating: IP65
Measurement and control equipment: D1C for inductive conductivity
Typical application: All types of soiled water, desalination control in cooling towers control
of electroplating baths, Cleaning in Place (CIP), product monitoring
ICT 1 for installation in pipes 1023244.
ICT 1-IMA-1 m ready fitted in in-line probe housing 1 m 1023349.
ICT 1-IMA-2 m ready fitted in in-line probe housing 2 m 1023351.
ICT 1-IM spare sensor for ICT 1-IMA-1 m 1023245.
and ICT-IMA-2 m
ProMinent®
6.22
Revised: 1st January 2015
6.9 DULCOTEST ® Conductivity Sensors
6.9.2
60
Description/version
148
G 3/4"
47
pk_6_082
Inductive Conductivity Sensors
26.4
Part no.
ICT 2
High performance sensors for aggressive media, maximum conductivity and high
temperatures up to 125 °C. Available for installation in tanks, pipes or the IMA-ICT 2 in-line
probe housing.
Measurement range: 0-2000 mS/cm
Cell constant: 2 cm-1
Reproducibility of
measurement: ±(5 mS/cm + 0.5 % of the measured value)
Temperature
compensation: Pt 100, class A, completely extrusion-coated
Medium temperature: 0 °C...125 °C
Note: for use together with D1C,
temperature compensation is limited to 100 °C
Max. pressure: 16 bar
Material: sensor: PFA, completely extrusion-coated
Assembly:
installation in pipes,
tanks (on the side): G 3/4 stainless steel thread(1.4571) with PTFE O-ring and
locknut (scope of supply)
or flange mounted: With accessories: Stainless steel flange ANSI 2 imperial 300lbs,
SS 316L (can be adapted to DIN counter-flange DN 50 PN 16)
Installation in immersion
pipe for tank from above: With accessories: IMA-ICT 2 in-line probe housing via stainless
steel flange DN 80 PN (see section 6.5.3)
Length when fitted: 1 m, diameter when fitted 70 mm
Power supply: 5 m fixed cable
Measurement and
control equipment: D1C
Enclosure rating: IP67
Typical applications: Production processes in the chemical industry,
Phase separation of product mixtures, Determining
concentrations of aggressive chemicals
ICT 2 Immersion assembly Type IMA-ICT 2
To hold an inductive conductivity sensor, type ICT 2.
Material fittings:
Stainless steel 1.4404
Material seal:
Viton®
Max. temperature:
125 °C
Max. pressure:
10 bar
Length:
1m
Pipe diameter:
70
Flange mounting for installation in tank
from above, stainless steel flange DN 80 PN 16
IMA-ICT 2
pk_6_094
Price
1023352.
1023353.
Note: See 'Green Pages' for local probe & controllers
6.23
ProMinent®
Revised: 1st January 2015
6.10 DULCOTEST ® Accessories
6.10.1 DULCOTEST® Electrolyte & Membrane Caps
Electrolyte for Sensors
Electrolyte for all CLE type chlorine sensors
100
Electrolyte for CDM 1 and CDE 3 type chlorine dioxide sensors
100
506271
Electrolyte for CDE 2 and CDR 1 type chlorine dioxide sensors
100
506272
Electrolyte for OZE type ozone sensors
100
506273
Electrolyte for CGE/CTE/BRE type sensors
506270
50
792892
Electrolyte for CDP type chlorine dioxide sensors
100
1002712
Electrolyte for PAA 1 type peracetic acid sensors
100
1023896
Electrolyte for CLT 1 type chlorite sensors
50
1022015
Electrolyte for PER 1 type hydrogen peroxide sensors
50
1025774
Electrolyte for CLO 1 type chlorine sensor
100
1035191
Electrolyte for CLO 2 type chlorine sensor
100
1035480
Electrolyte for CBR 1 type chlorine/bromine sensor
Electrolyte for BCR 1 type bromine sensor
100
50
1038017
1044843
Membrane Caps for Sensors
Cap has a red dot
Cap is orange
Cap is blue
Membrane cap for types CLE II T, CDM 1 and OZE 1
–
790486
Membrane cap for types: CLE 2.2, CLE 3, CDE 1.2, CDE 2, OZE 2 & OZE 3 –
790488
Sensor cap for CLO 1
–
1035197
Sensor cap for CLO 2
–
1035198
Membrane cap for CGE/CTE 1 (2/5/10 ppm) and BRE 1 (10 ppm), BRE 2
–
792862
Membrane cap for CTE 1 (0.5 ppm), CBR 1, BCR 1
–
741274 Membrane cap for CDP 1, BRE 1 (0.5 / 2 ppm), CLT
–
1002710
Membrane cap for CDE 3
–
1026578
Membrane cap for PAA 1, CDR 1
–
1023895
Membrane cap for PER 1
–
1025776
Membrane cap for H2.10 P
–
792978
(10 ppm), BRE 2 (2 membrane caps + electrolyte)
50
740048
Accessory set for CTE 1 (0.5 ppm) (2 membrane caps + electrolyte)
50
741277
100
1024611
Accessory Sets for Sensors
Accessory set for CGE 2/CTE 1 (2/5/10 ppm) and BRE 1
Accessory set for CLE (2 membrane caps + electrolyte)
Accessory set for CDP 1 (2 membrane caps + electrolyte),
100
1002744
Accessory set for PAA 1 (2 membrane caps + electrolyte)
BRE 1 (0.5 / 2 ppm), CLT
100
1024022
Accessory set for PER 1 (2 membrane caps + electrolyte)
50
1025881
Accessory set for CDE 3 (2 membrane caps + electrolyte)
100
1026361
Accessory set for CLO 1 (electrolyte, grinding disc, plug)
100
1035482
Accessory set for CLO 2 (electrolyte, grinding disc, plug)
100
1035483
Accessory set for CBR 1 (2 membrane caps + electrolyte)
Accessory set for BCR1 (2 membrane caps + electrolyte)
100
100
1038984
1044844
ProMinent®
6.24
Revised: 1st January 2015
Te c h n i c a l D a t a D G M
DGM modular in-line probe housing
For conductivity, Pt 100, pH or redox probes with 13.5 PG internal thread or
chlorine, bromine, chlorine dioxide, ozone measuring cells with R 10 internal thread.
• Simple to assemble (already mounted on panel up to max. 5 units)
• Expansion options
• Water flow monitor module
• Simple to calibrate measured variables due to low sample water volume
Input-side ball valve for stopping and adjusting flow
Every fully mounted DGM set is fitted with a simple sampling tap
pk_5_080_1
Material:
Transparent PVC (all modules)
Viton® (seals)
PP (calibration cup)
PVC white (mounting panel)
Max. temperature:
60 °C
Max. pressure:
6 bar (30 °C)
1 bar (60 °C)
2 bar (note: with flow monitor ... typical)
Flow volume:
Up to 80 l/h (40 l/h recommended)
Flow sensor:
Reed contact
max. switch power 3 W
max. switch voltage 175 V
max. switch current 0.25 A
max. operating current 1.2 A
max. contact resistance 150 mý
Switch hysteresis:
approx. 20 %
Enclosure rating:
IP 65
Applications:
Potable, swimming pool water or water of similar quality with no
suspended solids
Assembly:
Max. 5 modules pre-assembled onto baseboard: more than
5 modules, pre-assembled onto baseboard as custom version,
priced accordingly.
6.25
ProMinent®
Revised: 1st January 2015
6.11 DULCOTEST ® Accessories
Modular In-Line Probe Housing DGM
Identity Code Ordering System For In-Line Probe Housing Modules
DGM
Flow Housing Module
A
Series Version
Flow monitor module:
0
No flow monitor
1With l/h scale
2
With gph scale (US)
***** Not Stocked *****
3
With flow monitor, l/h scale
4
With flow monitor, gph scale (US)
***** Not Stocked *****
0
1
2
3
4
Number of PG 13.5 modules:
No PG 13.5 modules
One PG 13.5 module
Two PG 13.5 modules
Three PG 13.5 modules
Four PG 13.5 modules
0
1
2
Number of 25 mm modules:
No 25 mm modules
One 25 mm module*
Two 25 mm modules*
Main material:
T
Transparent PVC
Seal material:
0Viton® A
Connections:
0
8 x 5 hose
1
PVC DN 10 threaded connector 9
Connector nipple/expansion module
Versions:
0
With ProMinent® logo
1
Without ProMinent® logo
Accessories included:
Wall mounting;
for Pg 13.5 module; calibration cup; Pg 13.5 probe assembly set.
The identity code opposite describes a fully assembled combination of
flow monitor with sensor, two Pg 13.5 modules (e.g. for pH and redox
probes) and a 25 mm module (e.g. for chlorine probe CLE 3). Fitted
with 8 x 5 hose connector.
Recommended accessories:
for potential equaliser plug
Part No.
791663.
flow sensor
791635.
additional calibration cup
791229.
Maric Flow Control Valve Assembly, 33 l/h
DGM
A
3
2
1
T
0
0
0
PA27002656 (connects to module) see GREEN PAGE Pricelist
Note: if using Maric flow control it is STRONGLY recommended that a
filter be used, refer section 4 GREEN PAGE PriceList
Flow Control Unit c/w float & sensor switch
1042687.
Flow Control plus pH Cell Unit
Flow Control plus pH Cell Unit & rH Unit
Flow Control plus Chlorine Cell includes Fitting Kit
Flow Control plus pH plus Chlorine Cell includes Fitting Kit
Flow Control plus pH plus rH Cell plus Chlorine Cell includes Fitting Kit
DGMA300T000
DGMA310T000
DGMA320T000
DGMA301T000
DGMA311T000
DGMA321T000
Note: ALL complete DGMA assemblies are supplied with a simple sampling tap.
For alternate by-pass, submersible and withdrawal probe Housings and Buffer Solutions, refer 'GREEN PAGE' Price List.
ProMinent®
6.26
Revised: 1st January 2015
6.12 DULCOTEST® Accessories
6.12.1
Accessories
Accessory: Sampling tap for DGMa
for PG 13.5 and 25 mm modules designed as a convenient ball valve.
Part No.
PG 13.5 sampling tap
1004737.
25 mm sampling tap
1004739.
pk_5_085
CABLES & CONNECTORS
SN6 coax connector for 5 mm dia. coax cable
304974.
SN6 coax connector for 3 mm dia coax cable
304975.
pk_5_071
CABLE & GLANDS
Coax Cable, per meter
pk_5_070
Military Grade, 50 ohm, type AM-900, Low Noise
A04001118
Grey HC2049 Cable, (2 core pulse)
A04001289
Grey cable entry gland 1/4" BSPM
703830.
Black cable entry gland 3/8" BSPM
703885.
ProMinent® DULCOTEST COMPLETE SIGNAL CABLES
2 x SN6 Coax 0.8 m - SS
305077.
2 x SN6 Coax 2.0 m - SS
304955.
2 x SN6 Coax 5.0 m - SS
304956.
2 x SN6 Coax 10.0 m - SS
304957.
Below cables for typical use with pH / ORP probes
SN6 - open end Coax 0.8m - S
*** use this for panels ***
SN6 - open end Coax 2.0m - S
305030.
SN6 - open end Coax 5.0m - S
305039.
SN6 - open end Coax 10.0m - S
SS
SB
S
1024105.
SN6 - open end Coax 20.0m - S
305040.
non-stock item
304952.
pk_5_071
The signal lead is required for connection of DMT type measuring
cells to the DMT transducer.
Universal cable, 5-pole round plug, 5-wire, 2 m
Universal cable, 5-pole round plug, 5-wire, 5 m
Universal cable, 5-pole round plug, 5-wire, 10 m
pk_1_085
1001300.
1001301.
1001302.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising