Directional Controls Vickers Mechanical Actuators Directional Control Valves 310 bar (4500 psi)

Directional Controls Vickers Mechanical Actuators Directional Control Valves 310 bar (4500 psi)
Vickers®
Service Data
Directional Controls
Mechanical Actuators Directional Control Valves
310 bar (4500 psi)
DG1V4-01**-10 Knob Operated
DG17V4-01**-10 Lever Operated
5150.01/EN/0999/S
DG17V4-01*C-10
283635 Knob
927023 Screw (2
Req’d)
(Torque .3--1.0 N.m
7-9 lbs.in.)
02--356381 Clevis
1483 Jam Nut
End Cap S/A (2 Req’d) (See Detail)
(Torque 24--30 N.m 18--22 lbf.ft.)
02--357442 Std
02--361725 F3
02--361726 F6
02--356387 Washer (2 Req’d)
398071 Plug
263492 “O” Ring (Std)
3289 Lever
02--356384
Identification
Plate
02--356377 Body
177920 “E” Ring
(3 Req’d)
Std Seal
F3 Seal
F6 Seal
199811
262334
200085
262338
262338
157515
263492
263492
154129
02-356378 02-360886 02-361724
Above parts included in seal kit:
STD KIT
F3 KIT
F6 KIT
02-363850 02-363851 02-363852
NOTE
Right hand assembly shown in all views.
For left hand, all parts except body and
nameplate are reversed.
Reverse spools for: 0, 2, 6, 7, 8, 22 & 33
DG17V4-01*A-10
Spring Offset -- Handle Out
02--355330
Spool Stop
DG17V4-01*N-10
02--360855 Clevis Pin
(3 Req’d)
256693 Link
283638 Bracket
8076 Screw (2 Req’d)
(Torque 2.3--2.8 N.m 20-25 lbs.in.)
262338 “O” Ring (Std & F3)
855897 Retaining Ring
02--343367 Plug Guide
02--356378 “U” Cup Seal
Builds otherwise same as
“C” spring centered model
02--356380 Spring
02--356387 Washer
(Spring end only)
02--355330
Spool Stop
02--357443 Detent S/A
(2 Req’d) (See Detail)
02--356382 Detent Housing
154595 Roll Pin
All Rights Reserved
DG17V4-01*A2-10
Spring Offset -- Handle In
02--356380 Spring
02--356387 Washer
(Spring end only)
Detent S/A
02--356383 Spring Detent
181880 Ball (3 Req’d)
 Eaton, 2001
End Cap S/A
02--356379 Centering Spring (2 Req’d)
02--344223 Centering Washer (2 Req’d)
Spool (Type 2 shown) (See Table page 4)
199811 “O” Ring (5 Req’d)
DG17V4-01**-(H)-M-S*-U(1)-10
End Cap S.A. (This End Only)
02--362458 -- ST’D.
02--362459 -- “F3”
02--362460 -- “F6”
617346 “U” Protection Cap
710776 “U1” Connector
711000 S/A Receptacle
02--147796 Wire (2 Req’d)
568616 Switch
568612 Cover
207896 Screw (2 Req’d.)
For S3 models, wire switch
normally open lugs to connector
pins 1 & 2
For S4 models, wire switch
normally closed lugs to connector
pins 1 & 2
02--344211 End Cover
568610 Gasket
524778 Body S/A for “H” Models
02--362457 Body S/A Non--“H” Models
End Cap S/A
262338 “O” Ring
855897 Retaining Ring
02--362448 Plug Guide
02--356378 “U” Cup Seal
Builds on this page otherwise
same as models shown on
page 2
DG17V4-01**-H-10
513456 Knob
524271 Handle S/A
513455 Cable Tie
504059 Boot
02--360874 Spool Stop
893031 Housing
02--303677 Cable Tie
513451 Screw (2 Req’d)
189128 Screw (2 Req’d)
(Torque 2.3--2.8 N.m
20-25 lbs.in.)
DG1V4-01**-10
1483 Jam Nut
02--357403 Knob
524778 Body S/A
End Cap S/A (This End Only.)
02--361729 Std
02--361730 F3
02--361731 F6
503927 Dust Cover
End Cap S/A
Bond Threads Using Loctite 271.
Grease Handle Using Lubriplate 630A.
262338 “O” Ring
855897 Retaining Ring
02--356378 “U” Cup Seal
02--361728 Plug Guide
Model Code
1
1
2
Interface seals
Blank - Buna N (std.)
F3 VIton (fire resistant seals)
F6 Nitrile seals (water glycol)
Viton is a registered trademark of E.I. DuPont Co.
2
Directional control
3
Mounting type
G4
Manifold or subplate
Control type
17 - Manual lever operated
1 - Knob operated
5
Flow direction
V4 - Four-way, 310 bar (4500 psi)
3
4
5
7
Spool type (crossover condition)
012367811 22 31 33 8
7 8
9
10
11
Open center, all ports
Open center, B blocked
Closed center
Closed center, P and B blocked
Closed center, P only
Closed center, T blocked
Open center, A and B blocked
Open center, A blocked
Closed center, 2-way
Closed center, A and P blocked
Closed center, bleed A & B
Spool/Spring arrangement
AA2 CN9
6
Spring offset (handle out)
Spring offset (handle in)
Spring centered
No spring detented
10
14
Handle
H-
Booted handle for harsh
environment
Omit if not required
11
Flag symbol
M - Electrical features (applies only to
switch models)
Omit if not required
12
Spool indicator switch
S3 - Switch wired normally open
S4 - Switch wired normally closed
Omit if not required
Switch connection
U - DIN 43650 connection for switch
U1 - DIN 43650 connector provided
for switch
Omit if not required
Left hand build
Valve size
14
Design number
Subject to change. Installation
dimensions remain as shown for design
numbers 10 through 19.
01 - ISO-4401-05, NFPA-D05 interface
SPOOL
13
13
Omit for standard right hand assembly
6
12
SPOOL TYPE
PART NO.
SYMBOL
AB
TYPE #0
02--355333
TYPE #1
02--362445
PT
AB
PT
AB
TYPE #2
02--343361
P T
AB
TYPE #3
TYPE #6
TYPE #7
02--355334
02--355335
02--355336
PT
AB
SPOOL NOTE:
For left hand build type 1 use 02--362446
For left hand build type 11 use 02--362445
For left hand build type 3 use 02--355337
For left hand build type 31 use 02--355334
PT
AB
PT
AB
TYPE #8
02--355342
PT
AB
TYPE #11
02--362446
PT
AB
TYPE #22
02--362447
PT
AB
TYPE #31
TYPE #33
02--355337
02--355338
PT
AB
PT
Printed in U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement