SFP-7040-WB 1.25Gbps SFP Bi-Directional Transceiver, 40km reach 1550nm Tx / 1310nm Rx

SFP-7040-WB 1.25Gbps SFP Bi-Directional Transceiver, 40km reach 1550nm Tx / 1310nm Rx
SFP-7040-WB
1.25Gbps SFP Bi-Directional Transceiver, 40km reach
1550nm Tx / 1310nm Rx
Features
Dual data-rate of 1.25Gbps/1.063Gbps operation
1550nm DFB laser and PIN photo-detector for 40km transmission
Compliant with SFP MSA and SFF-8472 with simplex LC receptacle
Digital Diagnostic Monitoring:
Internal Calibration or External Calibration
Compatible with SONET OC-24-LR-1
Compatible with RoHS
+3.3V single power supply
Operating case temperature:
Standard :
0 to +70°C
Applications
Gigabit Ethernet
Fiber Channel
Switch to Switch interface
Switched backplane applications
Router/Server interface
Other optical transmission systems
Description
The SFP-BIDI transceivers are high performance, cost effective modules supporting dual data-rate of
1.25Gbps/1.0625Gbps and 40km transmission distance with SMF.
The transceiver consists of three sections: a DFB laser transmitter, a PIN photodiode integrated with a
trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety
requirements.
The transceivers are compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further
information, please refer to SFP MSA.
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA
www.robofiber.com
Page 1 of 9
Rev.1.3 Nov 14/2012
TD+/TxFault
TxDis
LD Driver
LD
Post Amp
PIN+TIA
LOS
RD+/-
Vcc
MCU
SCL
SDA
EEPROM
ADC/DAC
Temp
Absolute Maximum Ratings
Table 1 - Absolute Maximum Ratings
Parameter
Symbol
Min
Max
Unit
Supply Voltage
Vcc
-0.5
4.5
V
Storage Temperature
Ts
-40
+85
°C
Operating Humidity
-
5
85
%
Recommended Operating Conditions
Table 2 - Recommended Operating Conditions
Parameter
Symbol
Operating Case Temperature
Standard
Min
Tc
0
Power Supply Voltage
Vcc
3.13
Power Supply Current
Icc
Typical
3.3
Gigabit Ethernet
1.25
Fiber Channel
1.063
Data Rate
Max
Unit
+70
°C
3.47
V
300
mA
Gbps
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA
www.robofiber.com
Page 2 of 9
Rev.1.3 Nov 14/2012
Optical and Electrical Characteristics
SFP-7040-WB: (DFB and PIN, 40km reach)
Table 3 - Optical and Electrical Characteristics
Parameter
Symbol
Min
Typical
Max
Unit
1550
1570
nm
1
nm
Notes
Transmitter
Centre Wavelength
λc
Spectral Width (-20dB)
∆λ
Side Mode Suppression Ratio
SMSR
30
Average Output Power
Pout
-5
Extinction Ratio
ER
9
Optical Rise/Fall Time (20%~80%)
tr/tf
Data Input Swing Differential
VIN
400
Input Differential Impedance
ZIN
90
1530
dB
0
dBm
1
dB
100
0.26
ns
1800
mV
110
Ω
2
Disable
2.0
Vcc
V
Enable
0
0.8
V
Fault
2.0
Vcc
V
Normal
0
0.8
V
1360
nm
-23
dBm
3
dBm
3
TX Disable
TX Fault
Receiver
Centre Wavelength
λc
1260
Receiver Sensitivity
Receiver Overload
-3
LOS De-Assert
LOSD
LOS Assert
LOSA
LOS Hysteresis
Data Output Swing Differential
-24
-35
dBm
dBm
1
4
dB
Vout
400
1800
mV
High
2.0
Vcc
V
0.8
V
4
LOS
Low
Notes:
1. The optical power is launched into SMF.
2. PECL input, internally AC-coupled and terminated.
7
-12
3. Measured with a PRBS 2 -1 test pattern @1250Mbps, BER ≤1×10 .
4. Internally AC-coupled.
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA
www.robofiber.com
Page 3 of 9
Rev.1.3 Nov 14/2012
Timing and Electrical
Table 4 - Timing and Electrical
Parameter
Symbol
Min
Typical
Max
Unit
Tx Disable Negate Time
t_on
1
ms
Tx Disable Assert Time
t_off
10
µs
Time To Initialize, including Reset of Tx Fault
t_init
300
ms
Tx Fault Assert Time
t_fault
100
µs
Tx Disable To Reset
t_reset
10
µs
LOS Assert Time
t_loss_on
100
µs
LOS De-assert Time
t_loss_off
100
µs
Serial ID Clock Rate
f_serial_clock
400
KHz
Vcc
V
0.8
V
MOD_DEF (0:2)-High
VH
MOD_DEF (0:2)-Low
VL
2
Diagnostics
Table 5 – Diagnostics Specification
Parameter
Range
Unit
Accuracy
Calibration
Temperature
0 to +70
°C
±3°C
Internal / External
Voltage
3.0 to 3.6
V
±3%
Internal / External
Bias Current
0 to 100
mA
±10%
Internal / External
TX Power
-5 to 0
dBm
±3dB
Internal / External
RX Power
-23 to -3
dBm
±3dB
Internal / External
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA
www.robofiber.com
Page 4 of 9
Rev.1.3 Nov 14/2012
Digital Diagnostic Memory Map
The transceivers provide serial ID memory contents and diagnostic information about the present
operating conditions by the 2-wire serial interface (SCL, SDA).
The diagnostic information with internal calibration or external calibration all are implemented, including
received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage
monitoring and temperature monitoring.
The digital diagnostic memory map specific data field defines as following.
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA
www.robofiber.com
Page 5 of 9
Rev.1.3 Nov 14/2012
Pin Definitions
Pin Diagram
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA
www.robofiber.com
Page 6 of 9
Rev.1.3 Nov 14/2012
Pin Descriptions
Pin
Signal Name
Description
Plug Seq.
Notes
1
VEET
Transmitter Ground
1
2
TX FAULT
Transmitter Fault Indication
3
Note 1
3
TX DISABLE
Transmitter Disable
3
Note 2
4
MOD_DEF(2)
SDA Serial Data Signal
3
Note 3
5
MOD_DEF(1)
SCL Serial Clock Signal
3
Note 3
6
MOD_DEF(0)
TTL Low
3
Note 3
7
Rate Select
Not Connected
3
8
LOS
Loss of Signal
3
9
VEER
Receiver ground
1
Note 4
10
VEER
Receiver ground
1
11
VEER
Receiver ground
1
12
RD-
Inv. Received Data Out
3
Note 5
13
RD+
Received Data Out
3
Note 5
14
VEER
Receiver ground
1
15
VCCR
Receiver Power Supply
2
16
VCCT
Transmitter Power Supply
2
17
VEET
Transmitter Ground
1
18
TD+
Transmit Data In
3
Note 6
19
TD-
Inv. Transmit Data In
3
Note 6
20
VEET
Transmitter Ground
1
Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage
between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low
state, the output will be pulled to less than 0.8V.
2) TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a
4.7k~10kΩ resistor. Its states are:
Low (0 to 0.8V):
Transmitter on
(>0.8V, < 2.0V):
Undefined
High (2.0 to 3.465V):
Transmitter Disabled
Open:
Transmitter Disabled
3) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on the host board.
The pull-up voltage shall be VccT or VccR.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is the clock line of two wire serial interface for serial ID
Mod-Def 2 is the data line of two wire serial interface for serial ID
4) LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor. Pull up voltage between 2.0V and
Vcc+0.3V. Logic 1 indicates loss of signal; Logic 0 indicates normal operation. In the low state, the output will be pulled to
less than 0.8V.
5) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be
terminated with 100Ω (differential) at the user SERDES.
6) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential
termination inside the module.
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA
www.robofiber.com
Page 7 of 9
Rev.1.3 Nov 14/2012
Recommended Interface Circuit
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA
www.robofiber.com
Page 8 of 9
Rev.1.3 Nov 14/2012
Mechanical Dimensions
Ordering information
Part Number
Product Description
SFP-7040-WB-SC
SFP-7040-WB
1550nm, 1.25Gbps, SC,40km, 0°C~+70°C, With Digital Diagnostic Monitoring
1550nm, 1.25Gbps, LC,40km, 0°C~+70°C, With Digital Diagnostic Monitoring
E-mail: [email protected]
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 USA
www.robofiber.com
Page 9 of 9
Rev.1.3 Nov 14/2012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement