E2A Extended Range DC-3 Wire Proximity Sensors Cylindrical Proximity Sensor

E2A Extended Range DC-3 Wire Proximity Sensors Cylindrical Proximity Sensor
Cylindrical Proximity Sensor
E2A
Extended Range DC-3 Wire
Proximity Sensors
• Ensures a sensing distance approximately
1.5 to 2 times longer than standard
proximity sensors.
• Minimizes collisions.
• Full range of standard sizes (M8, M12, M18
and M30; both long and short barrels).
• Choose from prewired, M8 or M12
connector versions.
Ordering Information (Shaded models are normally stocked.)
Size Type
Sensing Connection
distance
M8 Shielded
2.0 mm
Pre-wired
Body
material
Model number
Thread Length Output
(overall length) configuration Operation mode NO
Stainless 27 (40)
steel
49 (62)
M12 connector Stainless 27 (43)
steel
49 (65)
Nickelplated
Brass
Unshielded
4.0 mm
27 (43)
49 (65)
M8 connector
(3-pin)
Stainless 27 (39)
steel
49 (61)
Pre-wired
Stainless 27 (40)
steel
49 (62)
M12 connector Stainless 27 (43)
steel
49 (65)
Nickelplated
Brass
M8 connector
(3-pin)
27 (43)
49 (65)
Stainless 27 (39)
steel
49 (61)
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
E2A-S08KS02-WP-B1 2M
E2A-S08KS02-WP-C1 2M
E2A-S08LS02-WP-B1 2M
E2A-S08LS02-WP-C1 2M
E2A-S08KS02-M1-B1
E2A-S08KS02-M1-C1
E2A-S08LS02-M1-B1
E2A-S08LS02-M1-C1
E2A-M08KS02-M1-B1
E2A-M08KS02-M1-C1
E2A-M08LS02-M1-B1
E2A-M08LS02-M1-C1
E2A-S08KS02-M5-B1
E2A-S08KS02-M5-C1
E2A-S08LS02-M5-B1
E2A-S08LS02-M5-C1
E2A-S08KN04-WP-B1 2M
E2A-S08KN04-WP-C1 2M
E2A-S08LN04-WP-B1 2M
E2A-S08LN04-WP-C1 2M
E2A-S08KN04-M1-B1
E2A-S08KN04-M1-C1
E2A-S08LN04-M1-B1
E2A-S08LN04-M1-C1
E2A-M08KN04-M1-B1
E2A-M08KN04-M1-C1
E2A-M08LN04-M1-B1
E2A-M08LN04-M1-C1
E2A-S08KN04-M5-B1
E2A-S08KN04-M5-C1
E2A-S08LN04-M5-B1
E2A-S08LN04-M5-C1
Operation mode NC
E2A-S08KS02-WP-B2 2M
E2A-S08KS02-WP-C2 2M
E2A-S08LS02-WP-B2 2M
E2A-S08LS02-WP-C2 2M
E2A-S08KS02-M1-B2
E2A-S08KS02-M1-C2
E2A-S08LS02-M1-B2
E2A-S08LS02-M1-C2
E2A-M08KS02-M1-B2
E2A-M08KS02-M1-C2
E2A-M08LS02-M1-B2
E2A-M08LS02-M1-C2
E2A-S08KS02-M5-B2
E2A-S08KS02-M5-C2
E2A-S08LS02-M5-B2
E2A-S08LS02-M5-C2
E2A-S08KN04-WP-B2 2M
E2A-S08KN04-WP-C2 2M
E2A-S08LN04-WP-B2 2M
E2A-S08LN04-WP-C2 2M
E2A-S08KN04-M1-B2
E2A-S08KN04-M1-C2
E2A-S08LN04-M1-B2
E2A-S08LN04-M1-C2
E2A-M08KN04-M1-B2
E2A-M08KN04-M1-C2
E2A-M08LN04-M1-B2
E2A-M08LN04-M1-C2
E2A-S08KN04-M5-B2
E2A-S08KN04-M5-C2
E2A-S08LN04-M5-B2
E2A-S08LN04-M5-C2
1
Ordering Information continued (Shaded models are normally stocked.)
Body
material
Model number
Thread Length Output
(overall length) configuration Operation mode NO
Nickelplated
Brass
34 (50)
M12 connector Nickelplated
Brass
34 (48)
Nickelplated
Brass
34 (50)
M12 connector Nickelplated
Brass
34 (48)
Nickelplated
Brass
39 (59)
M12 connector Nickelplated
Brass
39 (53)
Nickelplated
Brass
39 (59)
M12 connector Nickelplated
Brass
39 (53)
Nickelplated
Brass
44 (64)
M12 connector Nickelplated
Brass
44 (58)
Size Type
Sensing Connection
distance
M12 Shielded
4.0 mm
Unshielded
M18 Shielded
Unshielded
M30 Shielded
Unshielded
8.0 mm
8.0 mm
Pre-wired
Pre-wired
Pre-wired
16.0 mm Pre-wired
15.0 mm Pre-wired
56 (72)
56 (70)
56 (72)
56 (70)
61 (81)
61 (75)
61 (81)
61 (75)
66 (86)
66 (80)
Nickelplated
Brass
44 (64)
(See note.)
66 (86)
20.0 mm M12 connector Nickelplated
Brass
30.0 mm
44 (58)
(See note.)
66 (80)
20.0 mm Pre-wired
30.0 mm
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
PNP
NPN
E2A-M12KS04-WP-B1 2M
E2A-M12KS04-WP-C1 2M
E2A-M12LS04-WP-B1 2M
E2A-M12LS04-WP-C1 2M
E2A-M12KS04-M1-B1
E2A-M12KS04-M1-C1
E2A-M12LS04-M1-B1
E2A-M12LS04-M1-C1
E2A-M12KN08-WP-B1 2M
E2A-M12KN08-WP-C1 2M
E2A-M12LN08-WP-B1 2M
E2A-M12LN08-WP-C1 2M
E2A-M12KN08-M1-B1
E2A-M12KN08-M1-C1
E2A-M12LN08-M1-B1
E2A-M12LN08-M1-C1
E2A-M18KS08-WP-B1 2M
E2A-M18KS08-WP-C1 2M
E2A-M18LS08-WP-B1 2M
E2A-M18LS08-WP-C1 2M
E2A-M18KS08-M1-B1
E2A-M18KS08-M1-C1
E2A-M18LS08-M1-B1
E2A-M18LS08-M1-C1
E2A-M18KN16-WP-B1 2M
E2A-M18KN16-WP-C1 2M
E2A-M18LN16-WP-B1 2M
E2A-M18LN16-WP-C1 2M
E2A-M18KN16-M1-B1
E2A-M18KN16-M1-C1
E2A-M18LN16-M1-B1
E2A-M18LN16-M1-C1
E2A-M30KS15-WP-B1 2M
E2A-M30KS15-WP-C1 2M
E2A-M30LS15-WP-B1 2M
E2A-M30LS15-WP-C1 2M
E2A-M30KS15-M1-B1
E2A-M30KS15-M1-C1
E2A-M30LS15-M1-B1
E2A-M30LS15-M1-C1
E2A-M30KN20-WP-B1 2M
E2A-M30KN20-WP-C1 2M
E2A-M30LN30-WP-B1 2M
E2A-M30LN30-WP-C1 2M
E2A-M30KN20-M1-B1
E2A-M30KN20-M1-C1
E2A-M30LN30-M1-B1
E2A-M30LN30-M1-C1
Operation mode NC
E2A-M12KS04-WP-B2 2M
E2A-M12KS04-WP-C2 2M
E2A-M12LS04-WP-B2 2M
E2A-M12LS04-WP-C2 2M
E2A-M12KS04-M1-B2
E2A-M12KS04-M1-C2
E2A-M12LS04-M1-B2
E2A-M12LS04-M1-C2
E2A-M12KN08-WP-B2 2M
E2A-M12KN08-WP-C2 2M
E2A-M12LN08-WP-B2 2M
E2A-M12LN08-WP-C2 2M
E2A-M12KN08-M1-B2
E2A-M12KN08-M1-C2
E2A-M12LN08-M1-B2
E2A-M12LN08-M1-C2
E2A-M18KS08-WP-B2 2M
E2A-M18KS08-WP-C2 2M
E2A-M18LS08-WP-B2 2M
E2A-M18LS08-WP-C2 2M
E2A-M18KS08-M1-B2
E2A-M18KS08-M1-C2
E2A-M18LS08-M1-B2
E2A-M18LS08-M1-C2
E2A-M18KN16-WP-B2 2M
E2A-M18KN16-WP-C2 2M
E2A-M18LN16-WP-B2 2M
E2A-M18LN16-WP-C2 2M
E2A-M18KN16-M1-B2
E2A-M18KN16-M1-C2
E2A-M18LN16-M1-B2
E2A-M18LN16-M1-C2
E2A-M30KS15-WP-B2 2M
E2A-M30KS15-WP-C2 2M
E2A-M30LS15-WP-B2 2M
E2A-M30LS15-WP-C2 2M
E2A-M30KS15-M1-B2
E2A-M30KS15-M1-C2
E2A-M30LS15-M1-B2
E2A-M30LS15-M1-C2
E2A-M30KN20-WP-B2 2M
E2A-M30KN20-WP-C2 2M
E2A-M30LN30-WP-B2 2M
E2A-M30LN30-WP-C2 2M
E2A-M30KN20-M1-B2
E2A-M30KN20-M1-C2
E2A-M30LN30-M1-B2
E2A-M30LN30-M1-C2
Note: M30 unshielded Models with double sensing distance and short barrels cannot be mounted due to the necessary separation
distance from the surrounding metal. Standard sensing models are thus available.
2
Specifications
DC 3-wire Models
Size
Type
Item
Sensing distance
Setting distance
Hysteresis
Target
Standard target (mild steel ST37)
Response frequency (See note 1.)
Power supply voltage
(operating voltage range)
Current consumption (DC 3-wire)
Output type
Control output
M8
Shielded
M12
Unshielded
Shielded
Unshielded
E2A-M12S04--B1
E2A-M08N04-M1-B1
E2A-M08S02-M1-B1
E2A-M12S04--B2
E2A-M08N04-M1-B2
E2A-M08S02-M1-B2
E2A-M12S04--C1
E2A-M08N04-M1-C1
E2A-M08S02-M1-C1
E2A-M12S04--C2
E2A-M08N04-M1-C2
E2A-M08S02-M1-C2
E2A-S08N04--B1
E2A-S08S02--B1
E2A-S08N04--B2
E2A-S08S02--B2
E2A-S08N04--C1
E2A-S08S02--C1
E2A-S08N04--C2
E2A-S08S02--C2
4 mm ±10%
4 mm ±10%
2 mm ±10%
0 to 3.2 mm
0 to 3.2 mm
0 to 1.6 mm
10% max. of sensing distance
Ferrous metal (The sensing distance decreases with non-ferrous metal.)
E2A-M12N08--B1
E2A-M12N08--B2
E2A-M12N08--C1
E2A-M12N08--C2
8 x 8 x 1 mm
12 x 12 x 1 mm
1,500 Hz
1,000 Hz
12 to 24 VDC. Ripple (p-p): 10% max.
(10 to 32 VDC)
10 mA max.
-B models: PNP open collector
-C models: NPN open collector
200 mA max. (32 VDC max.)
24 x 24 x 1 mm
800 Hz
12 x 12 x 1 mm
1,000 Hz
8 mm ±10%
0 to 6.4 mm
Load current
(See note 2.)
Residual voltage 2 V max. (under load current of 200 mA with cable length of 2 m)
Indicator
Operation indicator (Yellow LED)
Operation mode
-B1/-C1 models: NO
(with sensing object approaching)
-B2/-C2 models: NC; For details, refer to the timing charts.
Protection circuit
Power source circuit reverse polarity protection,
Output reverse polarity protection, Power source
Surge suppressor, Short-circuit protection
circuit reverse polarity protection, Surge suppressor,
Short-circuit protection
Ambient air temperature
Operating: -40°C to 70°C, Storage: -40°C to 85°C (with no icing or condensation)
Temperature influence
±10% max. of sensing distance at 23°C within temperature range of -25°C to 70°C
(See note 2.)
±15% max. of sensing distance at 23°C within temperature range of -40°C to 70°C
Ambient humidity
Operating: 35% to 95%, Storage: 35% to 95%
Voltage influence
±1% max. of sensing distance in rated voltage range ±15%
Insulation resistance
50 MΩ min. (at 500 VDC) between current carry parts and case
Dielectric strength
1,000 VAC at 50/60 Hz for 1 min between current carry parts and case
Vibration resistance
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y and Z directions
Shock resistance
1,000 m/s2, 10 times each in X, Y and Z directions
500 m/s2, 10 times each in X, Y and Z directions
Standards and listings
IEC60529: IP67, Degree of protection
EN60947-5-2: EMC
UL (CSA) [E196555] (See note 3.)
Connection method
-WP models: Pre-wired models (Standard length: 2 m)
-M1 models: M12 4-pin connector models
-M5 models: M8 3-pin connector models
Weight
Pre-wired model
Approx. 65 g
Approx. 85 g
(packaged)
M12 connector model M12 connector models: Approx. 20 g
Approx. 35 g
M8 connector models: Approx. 15 g
Material
Case
Stainless steel or brass-nickel plated
Brass-nickel plated
Sensing surface
PBT
Cable
PVC
Clamping nut
Brass-nickel plated
Note 1. The response frequency is an average value. Measurement conditions are as follows: standard target, a distance of twice the
standard target distance between targets, and a setting distance of half the sensing distance.
2. When using any model at an ambient temperature between -40°C and -25°C and a power voltage between 30 and 32 VDC,
use a load current of 100 mA max.
3. UL (CSA) [E196555]: Use class 2 circuit only.
3
Specifications continued
DC 3-wire Models
Size
Type
Item
M18
Shielded
M30
Unshielded
Shielded
Unshielded
Unshielded
E2A-M18S08--B1 E2A-M18N16--B1 E2A-M30S15--B1 E2A-M30KN20--B1 E2A-M30LN30--B1
E2A-M18S08--B2 E2A-M18N16--B2 E2A-M30S15--B2 E2A-M30KN20--B2 E2A-M30LN30--B2
E2A-M18S08--C1 E2A-M18N16--C1 E2A-M30S15--C1 E2A-M30KN20--C1 E2A-M30LN30--C1
E2A-M18S08--C2 E2A-M18N16--C2 E2A-M30S15--C2 E2A-M30KN20--C2 E2A-M30LN30--C2
Sensing distance
Setting distance
Hysteresis
Target
Standard target (mild steel ST37)
Response frequency (See note 1.)
Power supply voltage
(operating voltage range)
Current consumption (DC 3-wire)
Output type
Control
output
8 mm ±10%
0 to 6.4 mm
16 mm ±10%
0 to 12.8 mm
15 mm ±10%
0 to 12 mm
20 mm ±10%
0 to 16 mm
10% max. of sensing distance
Ferrous metal (The sensing distance decreases with non-ferrous metal.)
60 x 60 x 1 mm
24 x 24 x 1 mm
48 x 48 x 1 mm
45 x 45 x 1 mm
100 Hz
500 Hz
400 Hz
250 Hz
30 mm ±10%
0 to 24 mm
90 x 90 x 1 mm
100 Hz
12 to 24 VDC. Ripple (p-p): 10% max.
(10 to 32 VDC)
10 mA max.
-B models: PNP open collector
-C models: NPN open collector
200 mA max. (32 VDC max.)
Load current
(See note 2.)
Residual voltage 2 V max. (under load current of 200 mA with cable length of 2 m)
Operation indicator (Yellow LED)
Indicator
Operation mode (with sensing -B1/-C1 models: NO
-B2/-C2 models: NC; For details, refer to the timing charts.
object approaching)
Output reverse polarity protection, Power source circuit reverse polarity protection, Surge suppressor,
Protection circuit
Short-circuit protection
Operating: -40°C to 70°C, Storage: -40°C to 85°C (with no icing or condensation)
Ambient air temperature
±10% max. of sensing distance at 23°C within temperature range of -25°C to 70°C
Temperature influence
(See note 2.)
±15% max. of sensing distance at 23°C within temperature range of -40°C to 70°C
Ambient humidity
Operating: 35% to 95%, Storage: 35% to 95%
Voltage influence
±1% max. of sensing distance in rated voltage range ±15%
Insulation resistance
50 MΩ min. (at 500 VDC) between current carry parts and case
Dielectric strength
1,000 VAC at 50/60 Hz for 1 min between current carry parts and case
Vibration resistance
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y and Z directions
Shock resistance
1,000 m/s2, 10 times each in X, Y and Z directions
Standards and listings
IEC60529: IP67, Degree of protection
EN60947-5-2: EMC
UL (CSA) [E196555] (See note 3.)
Connection method
-WP models: Pre-wired models (Standard length: 2 m)
-M1 models: M12 4-pin connector models
-M5 models: M8 3-pin connector models
Pre-wired model
Weight
Approx. 160 g
Approx. 280 g
Approx. 280 g
Approx. 370 g
(packaged) M12 connector
Approx. 70 g
Approx. 200 g
Approx. 200 g
Approx. 260 g
model
Case
Material
Brass-nickel plated
Sensing surface
PBT
Cable
PVC
Clamping nut
Brass-nickel plated
Note 1. The response frequency is an average value. Measurement conditions are as follows: standard target, a distance of twice the
standard target distance between targets, and a setting distance of half the sensing distance.
2. When using any model at an ambient temperature between -40°C and -25°C and a power voltage between 30 and 32 VDC,
use a load current of 100 mA max.
3. UL (CSA) [E196555]: Use class 2 circuit only.
4
Engineering Data
Operating Range (Typical)
Influence of Sensing Object Size and Materials
5
Engineering Data continued
6
Operation
PNP Output
Operation mode
NO
Model
NC
E2A---B2
Timing chart
Output circuit
Timing chart
Output circuit
E2A---B1
NPN Output
Operation mode
NO
Model
NC
E2A---C2
E2A---C1
7
Dimensions
Note: All units are in millimeters unless otherwise indicated.
Pre-wired Models (Shielded)
8
Pre-wired Models (Unshielded)
Dimensions continued
Note: All units are in millimeters unless otherwise indicated.
Pre-wired Models (Shielded)
Pre-wired Models (Unshielded)
9
Dimensions continued
Note: All units are in millimeters unless otherwise indicated.
M12 Connector Models (Shielded)
10
M12 Connector Models (Unshielded)
Dimensions continued
Note: All units are in millimeters unless otherwise indicated.
M8 Connector Models (Shielded)
M8 Connector Models (Unshielded)
11
Precautions
Safety Precautions
Power Supply
Do not impose an excessive voltage on the E2A, otherwise it
may be damaged. Do not impose AC current (100 to 240
VAC) on any DC model, otherwise it may be damaged.
Load Short-circuit
Do not short-circuit the load, or the E2A may be damaged.
The E2A’s short-circuit protection function will be valid if the
polarity of the supply voltage imposed is correct and within
the rated voltage range.
Wiring
Be sure to wire the E2A and load correctly, otherwise it may
be damaged.
Connection with No Load
Be sure to insert loads when wiring. Make sure to connect a
proper load to the E2A in operation, otherwise it may damage
internal elements.
Do not expose the product to flammable or
explosive gases.
Do not disassemble, repair, or modify the product.
Correct Use
Power Reset Time
The Proximity Sensor is ready to operate within 100 ms after
power is supplied. If power supplies are connected to the
Proximity Sensor and load respectively, be sure to supply
power to the Proximity Sensor before supplying power to
the load.
Effects of Surrounding Metal
When mounting the E2A within a metal panel, ensure that the
clearances given in the following table are maintained.
Type
Dimension M8
Shielded l
m
d
D
n
Nonshielded
l
m
d
D
n
M12 M18
0
0
4.5
–
0
12
12
8
24
12
24
12
–
0
18
15
20
40
15
40
M30
Short
Long
barrel barrel
0 (See 0
note 1) (See note 2)
24
45
27
45
1.5
4
27
45
22
30
40
48
70
90
70
90
120
22
30
40
70
90
120
Note 1. In the case of using the supplied nuts. If true flush mounting
is necessary, apply a free zone of 1.5 mm.
2. In the case of using the supplied nuts. If true flush mounting
is necessary, apply a free zone of 4 mm.
12
Power OFF
The Proximity Sensor may output a pulse signal when it is
turned OFF. Therefore, it is recommended that the load be
turned OFF before turning OFF the Proximity Sensor.
Power Supply Transformer
When using a DC power supply, make sure that the DC
power supply has an insulated transformer. Do not use a DC
power supply with an auto-transformer.
Mutual Interference
When installing two or more Sensors face-to-face or side-byside, ensure that the minimum distances given in the
following table are maintained.
Type
Dimension M8
Shielded A
B
NonA
shielded B
20
15
80
60
M12 M18
30
20
120
100
60
35
200
120
M30
Short
barrel
110
70
300
200
Long
barrel
300
300
Precautions continued
Wiring
High-tension Lines
Wiring through Metal Conduit:
If there is a power or high-tension line near the cable of the
Proximity Sensor, wire the cable through an independent
metal conduit to prevent against Proximity Sensor damage or
malfunctioning.
Maintenance and Inspection
Cable Extension
Standard cable length is less than 200 m.
2. Check for loose wiring and connections, improper contacts,
and line breakage.
The tractive force is 50 N.
3. Check for attachment or accumulation of metal powder
or dust.
Mounting
The Proximity Sensor must not be subjected to excessive
shock with a hammer when it is installed, otherwise the
Proximity Sensor may be damaged or lose its waterresistivity.
Do not tighten the nut with excessive force. A washer must
be used with the nut.
Periodically perform the following checks to ensure stable
operation of the Proximity Sensor over a long period of time.
1. Check for mounting position, dislocation, looseness, or
distortion of the Proximity Sensor and sensing objects.
4. Check for abnormal temperature conditions and other
environmental conditions.
5. Check for proper lighting of indicators (for models with a
set indicator.)
Never disassemble or repair the Sensor.
Environment
Water Resistivity
Do not use the Proximity Sensor underwater, outdoors, or in
the rain.
Type
M8
M12
M18
M30
Stainless steel type
Brass type
Torque
9 N·m
4 N·m
30 N·m
70 N·m
180 N·m
Operating Environment
Be sure to use the Proximity Sensor within its operating
ambient temperature range and do not use the Proximity
Sensor outdoors so that its reliability and life expectancy can
be maintained. Although the Proximity Sensor is water
resistive, a cover to protect the Proximity Sensor from water
or water-soluble machining oil is recommended so that its
reliability and life expectancy can be maintained.
Do not use the Proximity Sensor in an environment with
chemical gas (e.g., strong alkaline or acid gasses including
nitric, chromic, and concentrated sulfuric acid gases).
Inrush Current
A load that has a large inrush current (e.g., a lamp or motor)
will damage the Proximity Sensor, in which case connect the
load to the Proximity Sensor through a relay.
13
Certain Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed part of all
catalogs, manuals or other documents, whether electronic or in writing, relating to
the sale of goods or services (collectively, the "Goods") by Omron Electronics LLC
and its subsidiary companies (“Seller”). Seller hereby objects to any terms or
conditions proposed in Buyer’s purchase order or other documents which are
inconsistent with, or in addition to, these Terms. Please contact your Omron
representative to confirm any additional terms for sales from your Omron company.
2. Prices. All prices stated are current, subject to change without notice by Seller. Buyer
agrees to pay the price in effect at time of shipment.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices sent
to Buyer after deducting transportation charges, taxes and duties, and will be allowed
only if (i) the invoice is paid according to Seller’s payment terms and (ii) Buyer has
no past due amounts owing to Seller.
4. Orders. Seller will accept no order less than $200 net billing.
5. Governmental Approvals. Buyer shall be responsible for, and shall bear all costs
involved in, obtaining any government approvals required for the importation or sale
of the Goods.
6. Taxes. All taxes, duties and other governmental charges (other than general real
property and income taxes), including any interest or penalties thereon, imposed
directly or indirectly on Seller or required to be collected directly or indirectly by
Seller for the manufacture, production, sale, delivery, importation, consumption or
use of the Goods sold hereunder (including customs duties and sales, excise, use,
turnover and license taxes) shall be charged to and remitted by Buyer to Seller.
7. Financial. If the financial position of Buyer at any time becomes unsatisfactory to
Seller, Seller reserves the right to stop shipments or require satisfactory security or
payment in advance. If Buyer fails to make payment or otherwise comply with these
Terms or any related agreement, Seller may (without liability and in addition to other
remedies) cancel any unshipped portion of Goods sold hereunder and stop any
Goods in transit until Buyer pays all amounts, including amounts payable hereunder,
whether or not then due, which are owing to it by Buyer. Buyer shall in any event
remain liable for all unpaid accounts.
8. Cancellation; Etc. Orders are not subject to rescheduling or cancellation unless Buyer
indemnifies Seller fully against all costs or expenses arising in connection therewith.
9. Force Majeure. Seller shall not be liable for any delay or failure in delivery resulting
from causes beyond its control, including earthquakes, fires, floods, strikes or other
labor disputes, shortage of labor or materials, accidents to machinery, acts of
sabotage, riots, delay in or lack of transportation or the requirements of any
government authority.
10.Shipping; Delivery. Unless otherwise expressly agreed in writing by Seller:
a. Shipments shall be by a carrier selected by Seller;
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Goods shall be FOB shipping point (unless otherwise
stated in writing by Seller), at which point title to and all risk of loss of the Goods
shall pass from Seller to Buyer, provided that Seller shall retain a security interest
in the Goods until the full purchase price is paid by Buyer;
d. Delivery and shipping dates are estimates only.
e. Seller will package Goods as it deems proper for protection against normal
handling and extra charges apply to special conditions.
11.Claims. Any claim by Buyer against Seller for shortage or damage to the Goods
occurring before delivery to the carrier must be presented in writing to Seller within
30 days of receipt of shipment and include the original transportation bill signed by
the carrier noting that the carrier received the Goods from Seller in the condition
claimed.
12.Warranties. (a) Exclusive Warranty. Seller’s exclusive warranty is that the Goods will
be free from defects in materials and workmanship for a period of twelve months
from the date of sale by Seller (or such other period expressed in writing by Seller).
Seller disclaims all other warranties, express or implied. (b) Limitations. SELLER
MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OF THE GOODS. BUYER ACKNOWLEDGES THAT IT ALONE HAS
DETERMINED THAT THE GOODS WILL SUITABLY MEET THE REQUIREMENTS OF
THEIR INTENDED USE. Seller further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Goods or otherwise of
any intellectual property right. (c) Buyer Remedy. Seller’s sole obligation hereunder
shall be to replace (in the form originally shipped with Buyer responsible for labor
charges for removal or replacement thereof) the non-complying Good or, at Seller’s
election, to repay or credit Buyer an amount equal to the purchase price of the Good;
provided that in no event shall Seller be responsible for warranty, repair, indemnity or
any other claims or expenses regarding the Goods unless Seller’s analysis confirms
that the Goods were properly handled, stored, installed and maintained and not
subject to contamination, abuse, misuse or inappropriate modification. Return of any
goods by Buyer must be approved in writing by Seller before shipment. Seller shall
not be liable for the suitability or unsuitability or the results from the use of Goods in
combination with any electrical or electronic components, circuits, system
assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as
an amendment or addition to the above warranty.
13.Damage Limits; Etc. SELLER SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE GOODS, WHETHER SUCH
CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Seller exceed the individual price of the Good on
which liability is asserted.
14.Indemnities. Buyer shall indemnify and hold harmless Seller, its affiliates and its
employees from and against all liabilities, losses, claims, costs and expenses
(including attorney's fees and expenses) related to any claim, investigation, litigation
or proceeding (whether or not Seller is a party) which arises or is alleged to arise
from Buyer's acts or omissions under these Terms or in any way with respect to the
Goods. Without limiting the foregoing, Buyer (at its own expense) shall indemnify
and hold harmless Seller and defend or settle any action brought against Seller to the
extent that it is based on a claim that any Good made to Buyer specifications
infringed intellectual property rights of another party.
15.Property; Confidentiality. The intellectual property embodied in the Goods is the
exclusive property of Seller and its affiliates and Buyer shall not attempt to duplicate
it in any way without the written permission of Seller. Notwithstanding any charges to
Buyer for engineering or tooling, all engineering and tooling shall remain the
exclusive property of Seller. All information and materials supplied by Seller to Buyer
relating to the Goods are confidential and proprietary, and Buyer shall limit
distribution thereof to its trusted employees and strictly prevent disclosure to any
third party.
16.Miscellaneous. (a) Waiver. No failure or delay by Seller in exercising any right and no
course of dealing between Buyer and Seller shall operate as a waiver of rights by
Seller. (b) Assignment. Buyer may not assign its rights hereunder without Seller's
written consent. (c) Amendment. These Terms constitute the entire agreement
between Buyer and Seller relating to the Goods, and no provision may be changed or
waived unless in writing signed by the parties. (d) Severability. If any provision hereof
is rendered ineffective or invalid, such provision shall not invalidate any other
provision. (e) Setoff. Buyer shall have no right to set off any amounts against the
amount owing in respect of this invoice. (f) As used herein, “including” means
“including without limitation”.
Certain Precautions on Specifications and Use
1. Suitability of Use. Seller shall not be responsible for conformity with any standards,
codes or regulations which apply to the combination of the Good in the Buyer’s
application or use of the Good. At Buyer’s request, Seller will provide applicable third
party certification documents identifying ratings and limitations of use which apply to
the Good. This information by itself is not sufficient for a complete determination of
the suitability of the Good in combination with the end product, machine, system, or
other application or use. The following are some examples of applications for which
particular attention must be given. This is not intended to be an exhaustive list of all
possible uses of this Good, nor is it intended to imply that the uses listed may be
suitable for this Good:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Energy control systems, combustion systems, railroad systems, aviation systems,
medical equipment, amusement machines, vehicles, safety equipment, and
installations subject to separate industry or government regulations.
(iii) Systems, machines and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to this Good.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO
LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS
BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE SELLER’S PRODUCT IS
PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
14
2. Programmable Products. Seller shall not be responsible for the user’s programming
of a programmable Good, or any consequence thereof.
3. Performance Data. Performance data given in this catalog is provided as a guide for
the user in determining suitability and does not constitute a warranty. It may
represent the result of Seller’s test conditions, and the user must correlate it to actual
application requirements. Actual performance is subject to the Seller’s Warranty and
Limitations of Liability.
4. Change in Specifications. Product specifications and accessories may be changed at
any time based on improvements and other reasons. It is our practice to change part
numbers when published ratings or features are changed, or when significant
construction changes are made. However, some specifications of the Good may be
changed without any notice. When in doubt, special part numbers may be assigned
to fix or establish key specifications for your application. Please consult with your
Seller’s representative at any time to confirm actual specifications of purchased
Good.
5. Errors and Omissions. The information in this catalog has been carefully checked and
is believed to be accurate; however, no responsibility is assumed for clerical,
typographical or proofreading errors, or omissions.
15
Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s
website at www.omron.com/oei - under the “About Us” tab in the Legal Matters section.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
OMRON ELECTRONICS LLC
OMRON CANADA, INC.
OMRON ON-LINE
One Commerce Drive
Schaumburg, IL 60173
847-843-7900
885 Milner Avenue
Toronto, Ontario M1B 5V8
416-286-6465
Global - http://www.omron.com
USA - http://www.omron.com/oei
Canada - http://www.omron.ca
For US technical support or other inquiries:
800-556-6766
Cat. No. D096-E3-01
16
12/03
Specifications subject to change without notice
Printed in USA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement