NWK(1,2) Quick Start Guide

NWK(1,2) Quick Start Guide
QUICK START GUIDE
INDUSTRIAL OUTDOOR 802.11A/N WIRELESS ETHERNET KIT
This manual serves the following
ComNet Model Numbers:
NWK1
NWK2
Thank you for purchasing NetWave® from ComNet. This quick start guide is designed to
walk you through installation.
This guide applies to the following models:
NWK1: Industrial Point to Point Kit, FCC Version (Includes NWK1_AP and NWK1_CL)
NWK2: Industrial Point to Point Kit, ETSI Version (Includes NWK2_AP and NWK2_CL)
An easy to read LED array displays unit operational status along with received signal
strength ensuring optimal installation and operation. See Figure 2 on Page 2 for LED
Indicator explanations.
See Figures 3 through 5 beginning on Page 3 for mounting instructions.
NWK1 Install Demo Video
Scan or visit: bit.ly/1bMJjwW
INS_NWK1_NWK2_QS_REV– 05/20/13 PAGE 1
QUICK START USER GUIDE
NWK1/NWK2
FIGURE 1 – NETWAVE® INDUSTRIAL WIRELESS ETHERNET LINK
FRONT
BACK
FIGURE 2 – STATUS LED INDICATIONS
LED
RSSI34 / STATUS
RSSI3
ETHERNET / RSSI2
POWER
POWER
ETHERNET / RSSI2
RSSI3
RSSI4 / STATUS
VISUAL CUE
INDICATION
SOLID GREEN
Power is supplied to the wireless unit
OFF
No power is supplied to the wireless unit
FLASH GREEN
Ethernet connection is established
SOLID YELLOW
Ethernet connection is established and there is activity present
RSSI Level is > Yellow LED Threshold
OFF
No Ethernet connection established. RSSI Level is < Yellow LED Threshold
SOLID GREEN
Good signal strength
FLASH GREEN
Unit is booting up
SOLID GREEN
Excellent signal strength
(Advisable to check Status Page to confirm RSSI is <70)
SIGNAL STRENGTH:
MINIMUM SIGNAL
TECH SUPPORT: 1.888.678.9427
MAXIMUM SIGNAL
INS_NWK1_NWK2_QS_REV– 05/20/13 PAGE 2
QUICK START USER GUIDE
NWK1/NWK2
FIGURE 3 – INSTALLATION INSTRUCTIONS
Step 1.
Unpack the mounting hardware from the box. Determine if this will be a pole or wall mount application.
The included Mounting kit is designed to support poles up to 3 in (7.6 cm) in diameter. If surface or wall mounting, the optional
NWBKT1 hardware will be required.
Step 2.
A.
Route the RJ45 connectorized Ethernet cable through the
weather tight gland connection as shown at left.
Note: The slit rubber washer allows a pre-terminated
Ethernet cable to be used.
Once the cable has been routed through the weather
connection as shown above, push the split rubber gasket
into place and loosely screw the cap that goes over the
rubber washer.
A
B
B. Snap the RJ-45 connector in place as shown
Step 3.
Slide the weather proof assembly over the cable so it can be
screwed into the enclosure gland. Make sure the rubber sealing
ring is in place as shown in step 2B.
Tighten the weather proof assembly into the enclosure and also
tighten the cap that squeezes the rubber washer over the Ethernet
cable as shown.
Step 4.
A.Connect one end of an RJ-45 Ethernet cable to the OUT
port of the Power Injection Module (PIM) and the other end
to LAN of the access point.
Maximum length of the RJ-45 CAT5 cable is 100 meters.*
A
B. Connect the RJ-45 Ethernet cable attached to the PIM to a
network device, such as to a switch or to the PC you will use
to configure the access point.
B
C.Connect the power adaptor to the main electrical supply
and the power plug into the socket of the PIM.
C
Ethernet
Network
D
D
PoE power input: Passive PoE (range 24 to 48 VDC)
The NWK(1,2) can also be powered by a suitable IEEE
802.3af/at PSE device such as a PoE switch or injector.
D.A Drip Loop is recommended as additional precaution
against moisture entering the Access Point housing.
* Up to 200mW radio. For higher power radio upgrade to higher rating
power adapter.
TECH SUPPORT: 1.888.678.9427
INS_NWK1_NWK2_QS_REV– 05/20/13 PAGE 3
QUICK START USER GUIDE
NWK1/NWK2
FIGURE 4 – POLE MOUNT INSTRUCTIONS
Included Hardware
Vertical Mount in -45º Position
Vertical Mount in +45º Position
FIGURE 5 – OPTIONAL POLE/WALL MOUNT HARDWARE
ComNet Part NWBKT1
TECH SUPPORT: 1.888.678.9427
INS_NWK1_NWK2_QS_REV– 05/20/13 PAGE 4
QUICK START USER GUIDE
NWK1/NWK2
INSTALLATION REQUIREMENTS
Shielded outdoor CAT 5 or better should be used for all out of plant Ethernet connection and should be properly grounded
through the PoE AC ground. Industrial grade shielded Ethernet cable is recommended to help prevent ESD damage commonly
experienced with outdoor installations. Visit www.comnet.net/comnet-products/cables
CONFIGURING NETWAVE
1. Connect an Ethernet cable from the port labelled as IN on the power Injection Module to either a laptop or a PC LAN port.
2. Connect the second Ethernet cable from the OUT port on the Power Injection Module to the NetWave LAN port.
3. Apply 24VDC to the Power Injection Module with the provided power supply. You should notice the green LED illuminate in
the Power Injection Module and the power LED on the NetWave unit.
4. Set the IP address of the laptop being used to configure NetWave to static and the subnet to 192.168.10.x/24 subnet.
5. Point the browser to 192.168.10.100 for the Access Point or 192.168.10.101 for the Client. These are the default addresses.
6. A login prompt will pop up. Enter:
ID: admin
Password: admin
7. Select the NETWORK SETTINGS tab and set the desired network settings.
Hit Apply Settings
Hit Save
NOTE: This will be the network address for the NetWave web server. It is not necessary to set to the same subnet as the
operating network but it is recommended.
8 Select the WIRELESS SETTINGS tab and set Country code – Only required if setting up the NWK2 (ETSI) model
NOTE: It is the user’s responsibility to ensure that the correct country is chosen. ComNet accepts no liability for incorrectly set
up equipment.
• Output RF power – if RSSI is greater than 70, it is recommended to reduce RF TX power at the connected remote node.
• Set SSID – if changing from the default setting
• Channel Spectrum Width – May want to reduce to 20M (or 10M) from the default 20/40M if the 5GHz spectrum is crowded or
connections across the link are unstable.
• Wireless Security – if changing from default settings
• Hit Apply Settings
• Hit Save
TECH SUPPORT: 1.888.678.9427
INS_NWK1_NWK2_QS_REV– 05/20/13 PAGE 5
QUICK START USER GUIDE
NWK1/NWK2
TYPICAL POINT-TO-POINT CONFIGURATION
NOTE: N
WK1 and NWK2 point to point kits have been set up at the factory and locked to each other. No need to set Wireless
Mode and may not need to set the IP address. These are designed to connect to each other once powered and properly
aligned.
Cat5 Cable
10/100Mbps
PC
NVR
ComNet Gigabit
Managed Switch
with 30W PoE+
PoE
NWK1_AP
(Access Point)
NWK1_CL
(Client)
PIM
or other
PSE device
IP
Camera
DEFAULT CONFIGURATIONS
IP Address of Web Server 192.168.10.100 for NWKx_AP and 192.168.10.101 for all other models
LAN Mode for Web Server
Static Addressing
Web Server User ID admin
Web Server Password
admin
Web Server Guest User ID
guest
Webserver Guest Passwordguest
SSIDNetWave-1
WPA Pre-shared Key
12345678
Channel-Frequency (AP)
Auto
Channel Spectrum Width
20/40M
Long Range Parameters
Enabled and defaulted to 1000m
NOTE: A Reset to defaults (performed on the ADMIN page) will erase all user configurations including the factory set MAC lock on
Point to Point (NWK1 or NWK2) Kit models.
TECH SUPPORT: 1.888.678.9427
INS_NWK1_NWK2_QS_REV– 05/20/13 PAGE 6
QUICK START USER GUIDE
NWK1/NWK2
AGENCY COMPLIANCE
FCC
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
Industry Canada
This Class A digital apparatus complies with Canadian ICES-003. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that permitted for
successful communication. This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
• This device may not cause interference, and
• This device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil numérique de la classe A est confrome à la norme NMB-003 Canada. Pour réduire le risque d’interférence aux autres
utilisateurs, le type d’antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) ne
dépasse pas ce qui est nécessaire
pour une communication réussie. Cet appareil est conforme à la norme RSS Industrie Canada exempts de licence norme(s). Son
fonctionnement est soumis aux deux conditions suivantes:
17 Compliance
• Cet appareil ne peut pas provoquer d’interférences et
• Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du
dispositif.
RF Exposure Warning
The antennas used for this transmitter must be installed to provide a separation distance of at least 2.52m from all persons and must
not be located or operating in conjunction with any other antenna or transmitter.
Les antennes utilisées pour ce transmetteur doivent être installé en considérant une distance de séparation de toute personnes d’au
moins 2.52m et ne doivent pas être localisé ou utilisé en conflit avec tout autre antenne ou transmetteur.
CE Marking
CE marking on this product represents the product is in compliance with all directives that are applicable to it.
This equipment may be operated in the following countries:
Austria, Belgium, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Malta, Netherlands,
Norway, Portugal, Romania, Czech Republic, Croatia, Slovakia, Slovenia, Sweden, UK
Installer Compliance Responsibility
Devices must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within
local country regulatory requirements.
RoHS/WEEE Compliance Statement
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be
disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular
household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated
collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential
negative consequences to the environment and human health. For more detailed information about the disposal of your old
equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
TECH SUPPORT: 1.888.678.9427
INS_NWK1_NWK2_QS_REV– 05/20/13 PAGE 7
QUICK START USER GUIDE
NWK1/NWK2
Need Additional Assistance?
Visit our website http://www.comnet.net or contact Comnet tech support:
Tel: (203) 796-5300
Toll free: (888) 678-9427
Email: [email protected]
Additional Technical support contact details can be found at:
http://www.comnet.net/services/technical-support.html
Or Visit our pre-sales design center:
http://www.comnet.net/services/design-center.html
Or our customer care:
http://www.comnet.net/services/customer-care.html
Additional Downloads
Datasheets, Installation manuals and other product documentation can be found at:
http://www.comnet.net/comnet-products/ethernet/wireless/
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | [email protected]
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | [email protected]
© 2014 Communications Networks Corporation. All Rights Reserved. “ComNet,” the “ComNet Logo,” “NetWave,” and the “NetWave Logo” are registered trademarks of Communication Networks, LLC.
INS_NWK1_NWK2_QS_REV– 05/20/13 PAGE 8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement