Groen HyPerSteam Pressureless Steamer Specification Sheet - Model HY

Groen HyPerSteam Pressureless Steamer Specification Sheet - Model HY
PROJECT NAME:
LOCATION:
HYPERSTEAM PRESSURELESS STEAMER
MODEL HY-5E/EF
ITEM NO:
QTY:
Steamer shall be a Groen Model HY-5E stainless steel pressureless steamer with a self-contained atmospheric
15.5 KW electric steam generator, per Bulletin 140807, as follows.
MODEL NO:
AIA NO:
SIS NO:
CONSTRUCTION: Steamer cavity and cabinet
shall be all stainless steel construction, with removable
right and left-side panels, providing access to internal
components. Steamer door is all stainless steel with a
strong continuous hinge and is field-reversible for left
or right-swing, door shall be provided with a one-piece,
replaceable seal. Easy-open handle and latch shall
provide positive lock and seal when door is pushed or
slammed shut. Hidden magnetic door switch cuts power
to blower and cuts power to generator when the door is
opened. Pan support racks shall be polished stainless
steel and removable for easy cleaning. A stainless steel
condensate collection tray is positioned under cavity
door.
FINISH: Cabinet exterior, including door, shall be
finished to a #3 uniform finish. Cavity interiors are
polished stainless steel. Control panel face plates
shall be smudge-resistant polyester film, ensuring
maximum ease in cleaning and maintaining an attractive
appearance.
UL LISTING: Steamer shall be UL-listed and
Canadian UL-listed.
SANITATION: Unit shall be designed and
distribution throughout cavity and between loaded
pans. Steam generator delivers 3.1 KW power
input per 2 1/2” deep steam pan. Heat-up time to
READY shall be 8-10 minutes or less, under normal
conditions. Cavity is kept warm and ready for instant
steam between loads. No cavity warm up required,
after READY light comes on. DELIME indicator light
warns operator of need to delime steam generator.
Unit will shut off if water level is low. When power is
turned “off”, unit automatically blows down the steam
generator to reduce sediment build-up.
ATMOSPHERIC STEAM GENERATOR:
Unit shall have an electric-heated, rear-mounted
steam generator to provide atmospheric steam to the
chamber at a temperature of approximately 212°F.
Steam generator has an electric water sensor. Electric
heating elements are replaceable from the side.
PAN CAPACITY:
Pan Size/Type
Number
12 x 20 x 1”
10
12 x 20 x 2 1/2”
5
12 x 20 x 4”
3
manufactured to meet NSF requirements and be
INSTALLATION: Unit requires 208, 240 or
NSF-listed. Unit shall allow operator to delime steam
480 Volt, single or three-phase electric service. Unit
generator through access port on top without tools or
requires dual 3/4” NH cold water supply lines and 2”
service call. Push button auto-delime feature is standard. free venting drain.
CONTROLS: Steamer controls shall include an
ON-OFF power button; 60-minute electro-mechanical
timer, with continuous steam setting; and READY light
which indicates when cavity is ready for steaming. AutoDelime button initiates deliming cycle.
PERFORMANCE FEATURES: Steamer cavity
shall have a powerful side-mounted blower, which
increases steam velocity and provides efficient steam
5-Pan capacity stainless steal pressureless steamer, table top, selfcontained, electric-heated.
(model HY-5E shown)
OPTIONS/ACCESSORIES:
Groen PureSteem™ Water
Treatment System
Factory stacking kit
Stainless steel support stand
Pan racks for support stand
4” adjustable legs
Single water connection (cold
water)
WATER SUPPLY REQUIREMENTS:
All steam systems are subject to contamination
and failure due to mineral content found in all
water supplies. To minimize service problems, a
Groen PureSteem™ Water Treatment System is
recommended.
ORIGIN OF MANUFACTURE: Designed and
manufactured in the United States.
HyPerSteam
140807 RevC
Revised 04/11
HY-5E/EF
P/N 125999 REV B
SERVICE CONNECTIONS & NOTES:
1
DRAIN CONNECTION: 2" [50.8] TUBE (DRAIN FREE VENTING).
2
COLD WATER SUPPLY AT 30 TO 60 PSIG WITH A FLOW RATE OF
0.75 - 1.50 GPM AND WITH A 3/4" NH CONNECTION.
3
ONE ELECTRICAL CONNECTION: 1" [25.4] CONDUIT FITTING.
4
MINIMUM REAR AND SIDE CLEARANCE: REAR = 6" [152.4]
LEFT SIDE = 2" [50.8] RIGHT SIDE = 2" [50.8]
5
DIMENSIONS IN BRACKETS [ ] ARE MM.
ELECTRICAL REQUIREMENTS
MAX.
KW
74.5
1
15.5
208
15.5
3
44.0
1
64.6
15.5
240
15.5
3
38.2
–––
–––
–––
480
3
19.1
15.5
VOLTAGE PHASE AMPS
8"
[203]
1 1/4"
[32]
1 1/4"
[32]
1
2
3
3" [76]
REAR OF STEAMER
MOUNTING HOLES IN BASE
USE 3/8" 16 BOLTS WHICH
MUST NOT EXTEND INTO STEAMER
BY MORE THAN 3/8" [10]
21 11/16"
[551]
30 13/16"
[783]
TREATED
WATER
UNTREATED
SUPPLY
WATER
CONNECTION
SUPPLY
CONNECTION
3" [76]
17 3/8"
[441]
2"
[51]
DETAIL VIEW
OF WATER CONNECTIONS
(IF 2nd CONNECTION ORDERED)
15 19/32"
[397]
4
4
30 1/8"
[765]
2"
[51]
6
[152]
4
UNIT FUSE
BOX
2
3
22 1/2"
[571]
15"
[381]
20 1/2"
[520]
1
1
1 5/8"
[41]
TABLE TOP OR COUNTER
(CUSTOMER PROVIDED) 1
21 5/8"
[549]
OPTIONAL 4" LEGS
11/16"
[17]
REAR OF TABLE
OR COUNTER
TABLE TOP OR COUNTER
33 3/8"
[772]
2
OPTIONAL SUPPORT STAND
3
21 9/16"
[548]
50 9/16"
[1284] MIN
1
48 1/2"
[1232]
43" MIN
[1092]
28 1/16"
[713] MIN
29 3/4"
[756] MIN
FINISHED FLOOR
6"
[152]
FRONT VIEW
1 1/2" [38] MINIMUM
2 5/8" [67] MAXIMUM
SIDE VIEW
OPTIONAL RACKS TO
HOLD (6) STEAMER PANS
1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.net
© 2013 Unified 125999REVB
Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement