Weslo Cadence 45 Treadmill User`s manual

Weslo Cadence 45 Treadmill User`s manual
Model No. WETL17105.0
Serial No.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction.
If you have questions, or if there
are missing or damaged parts,
please contact the establishment
where you purchased this product.
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
USER'S MANUAL
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: A PART IDENTIFICATION CHART, an EXPLODED DRAWING, and a PART LIST are attached in the
center of this manual.
WESLO is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
11. If an extension cord is needed, use only a 3conductor, 1mm2 (14-gauge) cord that is no
longer than 1.5 m (5 ft.).
2. Use the treadmill only as described.
12. Keep the power cord away from heated surfaces.
3. Place the treadmill on a level surface, with at
least 2.5 m (8 ft.) of clearance behind it and
0.5 m (2 ft.) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See MAINTENANCE AND TROUBLESHOOTING on page
13 if the treadmill is not working properly.)
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Read, understand, and test the emergency
stop procedure before using the treadmill (see
OPERATION AND ADJUSTMENT on page 9).
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should not be used by persons
weighing more than 113 kg (250 lbs.).
17. Never leave the treadmill unattended while it is
running. Always remove the key and unplug
the power cord when the treadmill is not in use.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes while
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes; never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6 and HOW TO FOLD
AND MOVE THE TREADMILL on page 12.)
You must be able to safely lift 20 kg (45 lbs.)
to raise, lower, or move the treadmill.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
10. When connecting the power cord (see page 9),
plug the power cord into an earthed circuit. No
other appliance should be on the same circuit.
When replacing the fuse, an ASTA approved
BS1362 type should be fitted to the fuse carrier.
A 13 amp fuse should be used.
20. Do not change the incline of the treadmill by
placing objects under the treadmill.
3
21. Inspect and properly tighten all parts of the
treadmill regularly.
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. Never drop or insert any object into any
opening.
23.
DANGER: Always unplug the power
24. This treadmill is intended for in-home use
only. Do not use this treadmill in any commercial, rental, or institutional setting.
cord immediately after use, before cleaning
the treadmill, and before performing the maintenance and adjustment procedures de-
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown at the right has been placed on the
treadmill. If the decal is missing or illegible, contact the
establishment where you purchased this product and
order a free replacement decal. Apply the decal in the location shown. Note: The decal is not shown at actual
size.
50%
4
BEFORE YOU BEGIN
using the treadmill. If you have questions after reading this manual, please see the front cover of this manual. To help us assist you, note the product model
number and serial number before calling. The model
number of the treadmill is WETL17105.0. The serial
number can be found on a decal attached to the treadmill (see the front cover of this manual for the location).
Thank you for selecting the WESLO® CADENCE A45
treadmill. The CADENCE A45 treadmill combines advanced technology with innovative design to let you
enjoy an excellent form of cardiovascular exercise in
the convenience and privacy of your home. And when
you’re not exercising, the unique CADENCE A45 treadmill can be folded up, requiring less than half the floor
space of other treadmills.
Before reading further, please familiarize yourself with
the parts that are labelled in the drawing below.
For your benefit, read this manual carefully before
Water Bottle Holder
(No water bottle is included)
Console
Handrail
Key/Clip
Storage Latch
RIGHT SIDE
LEFT SIDE
Hood
Circuit Breaker
On/Off Switch
Walking Belt
Wheel
Foot Rail
Incline Leg
Rear Roller
Adjustment Bolts
5
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
remove the long wire inside of the right handrail yet. In addition, do not dispose of the packing materials
until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance
lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the
shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt, simply
wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex key
spanner
, and wire cutters
and your own phillips screwdriver
.
, adjustable
Note: To identify small parts used during assembly, see the PART IDENTIFICATION CHART in the center of
this manual. Some parts may be preassembled.
1. Attach the six Base Pads (19) to the bottom of the Base
(71) with six Base Pad Screws (42).
1
71
42
42
19
19
42
19
42
19
2. Have a second person hold the Base (71) in the position
shown.
42
19
2
Bend
Identify the Right Handrail (6), which has a large hole near
the lower end. Hold the Right Handrail so the bend is in
the position shown. Attach the Right Handrail to the
Base (71) with two Handrail Bolts (12), Handrail Washers
(30), and Nuts (17). Do not tighten the Handrail Bolts
yet.
7
6
Attach the Left Handrail (7) to the Base (71) in the same
way.
71
12
Large
Hole
30
17
6
12
3. With the help of a second person, raise the Handrails
(6, 7) so the Base (71) is flat on the floor.
3
7
6
Attach the Wheels (15) to the inner sides of the Base
(71) with two Wheel Bolts (14) and two Nuts (17). Do not
overtighten the Nuts; the Wheels should turn freely.
14
15
55
Position the treadmill Frame (55) between the Handrails
(6, 7) as shown. See the inset drawing. Locate the wire
tie in the lower end of the Right Handrail (6). Tie the wire
tie securely to the connector on the end of the Wire
Harness (22). Next, pull the opposite end of the wire tie
until the Wire Harness is routed through the Right
Handrail. Secure the Wire Harness to the upper end of
the Right Upright so that it will not fall inside. Then, disconnect and discard the wire tie.
22
17
71
Tie
22
4. Have a second person lift and hold the front end of the
Frame (55). Hold a Frame Spacer (13) between the Right
Handrail (6) and the Frame. Attach the Right Handrail to
the Frame with a Frame Bolt (10), a Handrail Washer
(30), and a Handrail Star Washer (60).
6
4
6
13
Repeat this step on the left side of the treadmill.
Disconnect and discard the wire tie (see step 3).
30
10
60
55
5. Hold the Console Base (1) near the Right Handrail (6).
Touch the Right Handrail to discharge any static.
5
1
Connector
Insert the end of the Wire Harness (22) through the three
looped plastic ties. Next, press the end of the Wire
Harness into the connector on the back of the Console
Base (1) in the location shown. The end of the Wire
Harness should slide easily into the connector and
snap into place. If it does not, turn the end of the Wire
Harness and then insert it. IF THE CONNECTORS ARE
NOT CONNECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS TURNED ON.
22
Plastic
Ties
6
22
7
6. Set the Console (1) on the Right Handrail (6) and the Left
Handrail (not shown). Start four Console Screws (70)
(only two are shown) into the Console. After you have
started all four Console Screws, tighten them.
6
1
Insert the excess Wire Harness (22) down into the Right
Handrail (6). Tighten the three plastic ties around the Wire
Harness, and then cut off the ends of the plastic ties.
22
Plastic
Ties
70
6
7. Attach the Console Back (4) to the Console (1) with four
16mm Screws (87). Note that there is a slot in the side of
the Console Back for the Wire Harness (22). Make sure
that no wires are pinched.
7
1
22
87
87
4
Slot
87
8. Carefully lower the Handrails (6, 7) to the floor. Center the
Frame (55) between the Handrails, and tighten the four
Handrail Bolts (12). Then, raise the Handrails to the vertical position.
8
12
55
See the inset drawing. Attach the Latch Assembly (41) to
the Left Handrail (7) with two 16mm Screws (87). Make
sure that the Latch Assembly is oriented as shown.
6, 7
64
63
See HOW TO CHANGE THE INCLINE OF THE TREADMILL on page 11. Adjust the Incline Legs (63) to the desired position, and fully insert the Incline Pins (64).
87
7
9. Make sure that all parts are properly tightened before
you use the treadmill. Keep the included hex key in a
secure place; the hex key is used to adjust the walking
belt (see page 14). To protect the floor or carpet, place a
mat under the treadmill.
8
41
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped
with a power cord having an equipment-earthing conductor and an
earthing plug. Important: If the power cord is damaged, it must
be replaced with a manufacturer-recommended power cord.
1
Socket on Treadmill
See drawing 1. Plug the indicated end of the power cord into the
socket on the treadmill.
See drawing 2. Plug the power cord into an appropriate outlet that is
properly installed and earthed in accordance with all local codes and
ordinances. Note: Your power cord and outlet may appear different.
Important: The treadmill is not compatible with GFCI-equipped
outlets.
DANGER:
Power
Cord
2
Outlet
Improper connection of the equipment-earthing conductor can result in an increased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as
to whether the product is properly earthed. Do not modify the plug provided with the product—if it will
not fit the outlet, have a proper outlet installed by a qualified electrician.
9
DIAGRAM OF THE CONSOLE
Note: If there is a sheet of clear plastic
on the console, remove the plastic.
Clip
Key
CAUTION: Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turning on the power.
• Always wear the clip (see the drawing
above) while operating the treadmill.
• Adjust the speed in small increments to
avoid sudden jumps in speed.
clip attached to the key (see the drawing above), and
slide the clip securely onto the waistband of your
clothes. Then, insert the key fully into the console.
After a moment, the display will light. Important: In an
emergency situation, the key can be pulled from
the console, causing the walking belt to slow to a
stop. Test the clip by carefully taking a few steps
backward; if the key is not pulled from the console,
adjust the position of the clip.
Follow the steps below to operate the console.
1
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only sealed water
bottles in the water bottle holders.
A moment after the key is inserted, the display will
light.
2
STEP-BY-STEP CONSOLE OPERATION
Before operating the console, make sure that the
power cord is properly
plugged in (see page 9).
Reset
Next, locate the on/off switch
on the treadmill frame near
the power cord. Make sure
that the on/off switch is in the reset position.
Insert the key fully into the console.
Press the Digital Speed increase button to start
the walking belt.
A moment after the button is pressed, the walking
belt will begin to move at 1 mph. Hold the handrails
and begin walking. As you exercise, change the
speed of the walking belt as desired by pressing
ETWL17105
the Digital Speed buttons. Each time a button is
(WLTL17105
pressed, the speed setting will change by 0.1
mph; if a button is held down, the speed setting
will change in increments of 0.5 mph.
Next, stand on the foot rails of the treadmill. Find the
10
hold down the Stop button for a few seconds. An
“E” for English miles or an “M” for metric kilometers
will appear in the priority display. Press the Digital
Speed increase button to change the unit of measurement if desired. When the desired unit of measurement is selected, remove the key and then
reinsert it.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display.
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and center the
walking belt if necessary (see page 14).
3
Monitor your progress with the display.
4
As you exercise, the lower
left corner of
the display
can show the
elapsed time
and the distance that you
have walked or run. The lower right corner of the
display can show the speed of the walking belt
and the approximate number of calories you have
burned.
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
remove the key from the console. Put the key in a
secure place. Then, switch the on/off switch to the
“off” position and unplug the power cord.
HOW TO CHANGE THE INCLINE OF THE TREADMILL
To vary the intensity of your exercise, you can change
the incline of the treadmill. There are three incline levels. Before changing the incline, remove the key
from the console and unplug the power cord. Next,
fold the treadmill to the storage position (see page 12).
The upper half of the display is the priority display.
The priority display can show the elapsed time, the
distance that you have walked or run, the speed of
the walking belt, or the approximate number of
calories you have burned. Press the Display button
repeatedly until the priority display shows the information that you are most interested in viewing.
Note: While information is shown in the priority display, the information will not be shown in the lower
left or right corner of the display.
To change the incline, first remove the incline pin from
one of the incline legs.
Adjust the inIncline
cline leg to
Pin
the desired
position, and
Incline
fully reinsert
Leg
the incline
pin. Adjust
Incline
the other inPin
cline leg in
the same
way. CAUTION: Make sure that both incline legs are at the
same position and that both incline pins are fully
inserted into the incline legs.
To reset the display, press the Stop button, remove the key, and then reinsert the key.
Note: The
console can
display speed
and distance
in either miles
or kilometers.
To see which
unit of measurement is selected, hold down the Stop button,
insert the key into the console, and continue to
After you have adjusted the incline legs, lower the
treadmill (see page 12).
ETWL17105
(WLTL17105
11
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Unplug the power cord. CAUTION: You must be able to
safely lift 20 kg (45 lbs.) to raise, lower, or move the
treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight. As you raise the frame, make sure to lift
with your legs rather than your back. Raise the frame
about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the hole in the
catch is aligned with the latch pin. Slowly release the
latch knob; make sure that the latch pin is fully inserted into the catch.
Frame
2
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 30° C (85° F).
Latch
Pin
Knob
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch
pin is fully inserted into the catch.
Handrail
1. Hold the handrails and place one foot against a wheel.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Wheel
3. Place one foot against one of the wheels, and carefully
lower the treadmill until it is in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2 above. Hold the treadmill with your right hand as shown. Pull the latch knob to the left and hold
it. Pivot the frame down until it is past the latch pin.
2. See drawing 1 above. Hold the metal frame firmly with both hands, and lower it to the floor. CAUTION: To
decrease the possibility of injury, do not lower the frame by gripping only the plastic foot rails. Do not
drop the frame to the floor. Make sure to bend your legs and keep your back straight.
12
MAINTENANCE AND TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 9.) If an extension cord is needed, use only a 3-conductor, 1 mm2 (14-gauge) cord that is no longer than 1.5
m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located on the treadmill frame
near the power cord. Make sure that the switch is in
the “on” position.
c
Tripped
Reset
d
On
Position
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Remove the five Screws (8) and the
two Foot Rail Screws (52). Next, remove the Hood (23).
a
23
52
8
8
52
8
Locate the Reed Switch (46) and the Magnet (49) on
the left side of the Pulley (53). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 3 mm (1/8 in.). If necessary, loosen
the Screw (92), move the Reed Switch slightly, and
then retighten the Screw. Reattach the Hood (not
shown), and run the treadmill for a few minutes to
check for a correct speed reading.
13
3 mm
92
46
Top View
53
49
PROBLEM: The walking belt slows when walked on
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1mm2 (14-gauge) cord that is no longer
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 5 to 7 cm (2 to 3
in.) off the walking platform. Be careful to keep the
walking belt centered. Then, plug in the power cord, insert the key, and walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
b
5–7 cm
Rear Roller
Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt has shifted to the left, first remove the key and UNPLUG THE POWER CORD.
Using the hex key, turn the left rear roller bolt clockwise 1/2 of a turn. Be careful not to overtighten the
walking belt. If the walking belt has shifted to the
right, turn the left rear roller bolt counterclockwise 1/2
of a turn. Then, plug in the power cord, insert the key,
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the hex key, turn both rear roller bolts clockwise, 1/4
of a turn. When the walking belt is correctly tightened,
you should be able to lift each edge of the walking
belt 5 to 7 cm (2 to 3 in.) off the walking platform. Be
careful to keep the walking belt centered. Then, plug
in the power cord, insert the key, and carefully walk
on the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
14
a
b
CONDITIONING GUIDELINES
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
WARNING:
Before beginning
this or any exercise program, consult your
physician. This is especially important for individuals over the age of 35 or individuals
with pre-existing health problems.
HOW TO MEASURE YOUR HEART RATE
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
To measure your heart
rate, stop exercising
and place two fingers
on your wrist as
shown. Take a six-second heartbeat count,
and then multiply the
result by ten to find
your heart rate. (A six-second count is used because
your heart rate will begin to slow when you stop exercising.)
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the desired
results is to exercise with the proper intensity. The
proper intensity level can be found by using your heart
rate as a guide. The chart below shows recommended
heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include three important parts:
A Warm-up—Warming up prepares the body for exercise by increasing circulation, delivering more oxygen
to the muscles, and raising the body temperature.
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up.
To find the proper heart rate for you, first find your age
at the top of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers below
your age. The three numbers are your “training zone.”
The lower two numbers are recommended heart rates
for fat burning; the highest number is the recommended heart rate for aerobic exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your heart rate is in
your training zone for 20 to 60 minutes. (During the
first few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20
minutes.) Breathe regularly and deeply as you exercise—never hold your breath.
Fat Burning
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help to prevent postexercise problems.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easily
accessible carbohydrate calories for energy. Only after
the first few minutes does your body begin to use
stored fat calories for energy. If your goal is to burn fat,
adjust the speed and incline of the treadmill until your
heart rate is near one of the lower two numbers in your
training zone.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
15
2 3/4” Bolt (47)–4
Star Washer (81)–4
Washer (29)–4
PART IDENTIFICATION CHART
Handrail Washer (11)–2
4” Bolt (120)–2
Remove this chart and use it to identify small parts during assembly. Save this chart and the EXPLODED
DRAWING/PART LIST for future reference.
Handrail Washer (30)–6
16mm Screw
(87)–6
Handrail Star
Washer (60)–2
Console Screw
(70)–4
Nut (17)–6
Base Pad
Screw (42)–6
Handrail Bolt (12)–4
Wheel Bolt (14)–2
Frame Bolt (10)–2
Ha
PART LIST—Model No. WETL17105.0
Key No.
Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
1
4
1
1
4
1
1
5
2
2
2
4
2
2
2
1
6
1
6
7
1
1
1
1
1
4
2
1
1
6
2
1
1
1
1
1
1
2
1
2
1
6
1
1
6
1
2
1
1
1
2
10
1
Description
Console
Round Endcap
Key/Clip
Console Back
Electronics Screw
Right Handrail
Left Handrail
Hood Screw
Motor Tension Bolt
Frame Bolt
Rear Roller Bracket Screw
Handrail Bolt
Frame Spacer
Wheel Bolt
Wheel
Right Rear Roller Bracket
Nut
Belly Pan Grommet
Base Pad
13mm Screw
Latch Warning Decal
Wire Harness
Hood
Left Rear Roller Bracket
Belly Pan
Belt Guide Screw
Belt Guide
6mm Hex Key
4mm Hex Key
Handrail Washer
Platform Bolt, Front
Controller Bracket
Front Roller Star Washer
Front Roller Adj. Bolt
Controller
Motor Bolt
Left Foot Rail
Motor Tension Nut
Motor Star Washer
Outlet Plate Screw
Storage Latch Assembly
Base Pad Screw
Drive Motor Assembly
Power Cord
Bracket Star Washer
Reed Switch
Platform Bolt, Rear
Reed Switch Clip
Magnet
Motor Belt
Rear Roller Adj. Bolt
Foot Rail Screw
Front Roller/Pulley
Key No.
Qty.
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
#
#
#
#
#
#
#
#
1
1
1
1
2
2
2
4
1
2
2
1
1
2
2
2
4
1
1
2
5
4
2
2
1
1
1
6
3
2
1
4
2
6
1
1
1
5
1
6
7
2
1
1
1
1
1
1
1
R0107B
Description
Right Foot Rail
Frame
Walking Belt
Walking Platform
Motor Bushing
Motor Bolt
Handrail Star Washer
8” Cable Tie
Motor Isolator
Incline Leg
Incline Pin
Ground Wire
Filter
Frame Endcap
U-nut
Cushion Fastener
Console Screw
Base
Rear Roller
Outlet Plate Washer
M4 Nut
Platform Nut/Incline Leg Nut
Platform Cushion
Front Isolator
Catch
Motor Bracket
Transformer
Plastic Tie
Controller Bolt/Ground Bolt
Incline Leg Bolt
Motor Pivot Nut
Incline Leg Washer
Rear Roller Star Washer
16mm Screw
Outlet Bracket Assembly
Circuit Breaker
On/Off Switch
Hood Clip
Grommet
Bracket Screw
M4.2 Screw
8” White Wire, 2 Female
4” Black Wire, Male/Female
8” Green/Yellow Wire, F/Ring
4” Green/Yellow Wire, F/Ring
4” Red Wire, M/F
10” Blue Wire, 2F
4” Blue Wire, 2F
User’s Manual
“#” indicates a non-illustrated part.
Specifications are subject to change without notice.
51
51
64 63
20
85
83
75
21
85
67
11
93
45
24
86
47
52
37
67
29
86
75
93
45
72
78
52
28
75
26
27
63
11
47
75
16 85
52
76
69
52
64
85
57
83
52
20
54
31
77
52
52
49
48
55
56
46
81
84
76
62
94
69
68
50
53
94
43
58
31
33
26
59 9
36
38
68
52
34
61
27
79
39
77
20
9
20
8
32
35
80
91
5
20
92
74
25
23
82
45
93
74
8
74
91
93
82
45
5
20
74
8
8
18
20
40
73
91
65
91
8
66
3
88
73
40
90
89
91
44
30
10
87
42
19
17
30
7
87
19
42
60
41
4
17
13
70
2
42
2
87
14
15
12
22
71
19
42
19
87
22
13
42
19
6
17
30
14
60
1
15
30
70
2
81
42
17
19
10
94
2
12
94
EXPLODED DRAWING—Model No. WETL17105.0
R0107B
ORDERING REPLACEMENT PARTS
To order replacement parts, please contact the establishment where you purchased this product. To help us assist
you, be prepared to provide the following information:
• the MODEL NUMBER of the product (WETL17105.0)
• the NAME of the product (WESLO CADENCE A45 treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING in the
center of this manual)
Part No. 244453 R0107B
Printed in China © 2007 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement