datasheet for EZ-410 by Asahi Kasei Microdevices

73

Hybrid Linear Hall Effect Ics EZ-series

EZ-410

Shipped in packet-tape reel(5000pcs/Reel)

EZ-410 is composed of an InAs Hall Element and a signal processing IC chip in a package

SMT Bipolar Hall

Effect Latch

Supply Voltage

3.8∼24Ｖ

Hall Element

Continuous

Excitation

Standard Sensitivity

Bop：5mT

Output

Open Collector

Notice:It is requested to read and accept "IMPORTANT NOTICE" written on the back of the front cover of this catalogue.

●Operational Characteristics

Vout

S

H

Marking

3

N

1

1：Vcc

2：GND

3：OUT

Bh

Vsat

Brp 0 Bop

N-pole

Magnetic flux density

L

S-pole

●Absolute Maximum Ratings （Ta=25℃）

Item

Supply Voltage

Symbol

Vcc

Output H Voltage Vo(off)

Output L Current I sink

Limit

24 （＊）

Vcc

10

Unit

V

V mA

Operating Temperature Range

Topr − 40 ∼ 125 ℃

Storage Temperature Range Tstg − 40 ∼ 150

℃

（＊）Please refer to Supply Voltage Derating Curve.

●Functional Block Diagram

1：Vcc

Reg.

3：OUT

Amp.

Voltage Regulator

Hall Element

Amplifer

2：GND

Output Stage

Schmitt Trigger

●Electrical Characteristicsw（Ta=−40∼125℃， Vcc=3.8∼24V）

Item

Supply Voltage

Symbol

V

CC

Output Leakage Current I leak

Conditions

OUT=''H''

Output Saturation Voltage

Vsat OUT=''L'', I out=10mA

Supply Current I cc OUT=''H''

Min.

3.8

Typ. Max.

Unit

12 24 V

5

1

0.4

9

μA

V mA

項 目

Supply Voltage

記号

V

CC

Output Leakage Current I leak

測 定 条 件

OUT=''H''

Output Saturation Voltage

Vsat OUT=''L''

Supply Current I cc OUT=''H''

（＊）Please refer to Supply Voltage Derating Curve.

最小

3.8

標準

12

最大

24

（＊1）

単位

V

10 μA

5

0.8

9

V mA

EZ-410

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff.

Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such

•This product contains galium arsenide(GaAs).Handling and discarding precsutions required.

Item

Operating Point

Symbol

B op

Release Point B rp

H y s t e r e s i s

B h

Conditions

●Package（Unit:mm)

●Magnetic Characteristicsw（Ta=−40∼125℃， Vcc=3.8∼24V）

Min. Typ. Max.

1 4.2

7.5

Unit mT

− 7.5

2

− 4.2

8.4

− 1

15 mT mT

Item

Operating Point

Symbol

B op

Conditions Min. Typ. Max.

0.5

4.2

8.5

Unit mT

Release Point B op

− 8.5

− 4.2

− 0.5

mT

H y s t e r e s i s B op

（＊）Please refer to Supply Voltage Derating Curve.

1 8.4

17 mT

●(For reference only)Land Pattern（Unit:mm)

0.6

2

φ0.3

Sensor center

0.6

0.15

0.90

c e

0.70

0.70

0.8

±0.1

1.2

±0.1

0∼0.1

3

3.6

±0.1

2.6

±0.1

1

1.30 1.30

0.4

Note)  The sensor center is located

    within the φ0.3mm circle.

0.4

1：Vcc

2：GND

3：OUT

●Temparature Dependence of Bop. Brp

0

−2

4

2

8

6

−4

−6

−8

−60 −40 −20

Bop

Brp

Vcc＝12V

0 20 40 60 80 100 120 140

Ambient Temperature（℃）

●Supply Voltage

25

20

15

10

5

0

–60 –40 –20 0 20 40 60 80 100 120 140

Ambient Temperature（℃） h p q

74

IMPORTANT NOTICE

 These products and their specifications are subject to change without notice.

When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the products.

 Descriptions of external circuits, application circuits, software and other related information contained in this document are provided only to illustrate the operation and application examples of the semiconductor products. You are fully responsible for the incorporation of these external circuits, application circuits, software and other related information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use of such information contained herein.

 Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials.

 AKM products are neither intended nor authorized for use as critical components system

Note2)

Note1)

in any safety, life support, or other hazard related device or

, and AKM assumes no responsibility for such use, except for the use approved with the express written consent by Representative Director of

AKM. As used here:

Note1) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability.

Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property.

 It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification.