CPRO-U4H1HFS

UHD 4 to 1 HDMI Switcher

DISCLAIMERS

The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document.

Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice.

COPYRIGHT NOTICE

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from

Cypress Technology.

© Copyright 2014 by Cypress Technology.

All Rights Reserved.

Version 1.0 May 2014

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this equipment:

• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.

• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.

• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO.

DATE DD/MM/YY SUMMARY OF CHANGE

VR0 25/03/15 Preliminary Release

CONTENTS

1. Introduction ............................................ 1

2. Applications ........................................... 1

3. Package Contents ................................ 1

4. System Requirements ............................ 1

5. Features .................................................. 2

6. Operation Controls and Functions ....... 3

6.1 Front Panel ........................................3

6.2 Rear Panel .........................................4

6.3 Remote Control ................................5

6.4 RS-232 Pin Assignment .....................5

6.5 IP Searching Software Application and Installation .......................................6

6.6 RS-232 & Telnet Commands ............7

6.7 EDID Content ....................................9

6.8 Telnet Control .................................10

6.9 WebGUI Control .............................12

7. Connection Diagram .......................... 14

8. Specifications ...................................... 15

9. Acronyms ............................................. 17

1. INTRODUCTION

The 4 by 1 HDMI Switcher enables the switching of four HDMI sources to a single HDMI output, allowing a display or AV Receiver to select between four devices. With fast switching technology the device can greatly eliminate the time required by swapping or turning ON/

OFF the connected displays. It supports 4K2K, 3D, 36-bit Deep Color,

Hi-Def. lossless audio and other features defined by the latest HDMI specifications. The management of source/sink scenarios can be operated easily through on-panel buttons, IR remote control, RS-232,

Telnet and WebGUI control.

2. APPLICATIONS

• Home Theater/Entertainment

• Lecture Room/Hall Presentation

• Show Room/Demo Room

• Public Commercial Display

• Information Board

3. PACKAGE CONTENTS

• UHD 4 to 1 HDMI Switcher

• Remote Control with Battery

• IR Receiver Cable

• 5V/2.6A DC Power Adaptor

• Operation Manual

4. SYSTEM REQUIREMENTS

Input source equipment such as Blu-ray/DVD/PS3 player or Set-Top-

Box and output HDMI TV/Display with connection cables.

1

5. FEATURES

• HDMI (with 3D & 4K2K supported) and HDCP compliant

• Select any one of four HDMI sources and display on a HDTV display with fast switching between sources

• Supports 3D signals pass-through

• Supports HDTV resolutions up to 4Kx2K (3840x2160@24/25/30, 50/60

YUV_420 & 4096x2160@24, 50/60 YUV_420)

• Supports HDMI data rate from 300Mbps to 3Gbps and 'Deep Color' up to 1080p/36-bit

• Supports selection of Standard (Fixed) or TV (Downstream) EDID settings

• Supports Audio pass-through of High-definition Audio formats (LPCM

2/5.1/7.1CH, Dolby Digital 2~5.1CH, DTS 2~5.1CH, Dolby TrueHD and

DTS-HD Master Audio)

• HDMI inputs support ‘Standard’ and ‘Apple’ HDCP modes.

Selecting ‘Apple’ mode guarantees the compatibility of Apple devices with this switcher

• Supports Telnet and WebGUI control

2

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWER SYNC INPUT 1 2 3 4

UHD 4 TO 1 SWITCHER

CPRO-U4H1HFS

1 2 3 4

1

IR Window: This IR Receiver receives the remote control signal from the packaged included remote control only with IR frequency at

38kHz.

2

POWER & LED: Press this button to turn ON the device or set the device to standby mode. The LED will illuminate in green when switch to ON. This device contains power last memory and therefore, when the power is connected the device will switch to

ON/Standby according to the last status.

*IP Reset: Press this button together with INPUT button for 3 second under power ON status, when the LED blink for once it means IP

Reset complete.

3

SYNC: This LED will illuminate when both input source and output display are linked with active signal.

4

IN 1~4: Press the INPUT button to select an input from the 4 input sources, LED will illuminated according to the selection.

3

6.2 Rear Panel

1 2

HDMI IN

3 4

HDMI OUT SERVICE CONTROL RS-232 IR IN DC 5V

1 2 3 4 5 6 7

1

HDMI IN: Connect from source equipment such as Blu-ray/DVD/

PS3 players, Set-Top-Box or any HDMI equipped source device for input signal sending. The device obtain auto detection function and will detect the last plug-in source for display on output when it is unplugged, the device will detect rotationally from 1~4 input source for display on output.

2

HDMI OUT: Connect to HDMI TV/display or HD Amplifier for output image and or audio display.

3

SERVICE: This slot is reserved for firmware update use only.

4

CONTROL: Connect from PC/Laptop with active internet service for Telnet or WebGUI control with RJ-45 terminated cable.

5

RS232: Connect from PC/Laptop for RS-232 command sending to control the device.

6

IR IN: Connect the IR Receiver included in the package for IR signal receive from the included remote control.

7

DC 5V: Connect the adaptor with power cord included in the package and connect to AC wall outlet for power supply.

4

6.3 Remote Control

1

POWER: Press this button to switch ON the device or to set it to standby mode.

2

INPUT: Press 1~4 to select input source.

POWER

1

1 2

3

INPUT

4

2

6.4 RS-232 Pin Assignment

PIN

1

2

3

Switcher

Assignment

NC

4

5

6

7

NC

NC

8

9

NC

NC

Baud Rate: 115200bps

Data Bit: 8 bits

Parity: None

Flow Control: None

Stop Bit: 1

Tx

Rx

NC

GND

5

CR-72

8

9

6

7

4

5

2

3

Remote Control

PIN

1

Assignment

NC

Rx

Tx

NC

GND

NC

NC

NC

NC

6.5 IP Searching Software Application and Installation

Please download the software from www.cypress.com.tw with file name CDPS V2.000 and save it in a directory where you may use it later.

Connect the Control System with PC/Laptop through the Ethernet port through an active network system and open the CDPS V2.000 application. Click on Find Devices on Network and a list of the devices connected to the Control System will show up.

Then user may use the IP Address to find the control device through

Telnet, WebGUI or even RS-232/Hyper Terminal tools.

6

6.6 RS-232 & Telnet Commands

COMMAND NAME

P0

P1

A N

IPCONFIG

SIPADDR XXX.XXX.

XXX.XXX

SNETMASK XXX.XXX.

XXX.XXX

SGATEWAY XXX.XXX.

XXX.XXX

HTTPPORT N

RSTIP

DESCRIPTION DESCRIPTION OF

PARAMETER

Power Off (Standby) NONE

Power On

Select Input N

Display The Current IP

Configure

NONE

N=1-4

NONE

Set Ethernet IP

Address

XXX=0~255

Set Ethernet Net Mask XXX=0~255

EDIDMODE

EDIDMODE N

EDIDALL

EDIDALL N

EDIDIN

EDIDIN N1

EDIDIN N1 N2

HDCPIN

HDCPIN N1

Set Ethernet

Gateway

XXX=0~255

Set Http Port Number N=0~65535

IP Configuration

Reset To <DHCP>

NONE

Show EDID Mode

Set EDID Mode

Show EDID Mode

Source For All

NONE

N=0(Appoint), 1(All)

NONE

N=1-9 (ref. EDID All) Set EDID Mode

Source For All

Show Input EDID

Source

Show Input N1 EDID

Source

Set Input N1 EDID

Source

Input HDCP Status

Show Input N1 HDCP

Status

NONE

N1=1-4

N1=1-4 N2=1-9 (ref.

EDID All)

NONE

N1=1-4

7

COMMAND NAME

HDCPIN N1 N2

DESCRIPTION DESCRIPTION OF

PARAMETER

Set Input N1 HDCP

On/Off*

N1=1-4 N2=0(OFF),

1(ON)

Show All Inputs Signal NONE

SOURCEDET

SOURCEDET N1

SINKINFO

INNAME

INNAME N1 N2

Show Input N1 Signal N1=1-4

Show Output

Information

NONE

Show Input Name NONE

Set Input Name N1=1-4

N2=ABCDEFGH(Max

Length=8)

Show Output Name NONE

OUTNAME

OUTNAME A N1

VER

Set HDMI Output

Name

Show Unit Firmware

Version

System Reboot

N1=ABCDEFGH(Max

Length=8)

NONE

REBOOT

NONE

HELP (?)

HELP N

Show Command List NONE

Show Descript Of

Command

N : COMMAND NAME

FADEFAULT

All Configure Set To

Factory Default

NONE

Note:

1. All the RS-232 command will be not executed unless followed with a carriage return. Commands are case-sensitive.

2. *HDCP ON/OFF equivalent to HDCP standard and Apple mode.

3. P address's default setting is on statics with 192.168.1.50

4. To find IP address in your zone an easy application is provided, please download it from http://zh-tw.cypress.com.tw/uploadfile/

CDPS_20140806_v2000.zip

8

6.7 EDID Content

Mode Selection

HDMI Output(TV)

8/2D/PCM/720p

Description

HDMI Output display EDID

Build-In EDID, Deep color/2D3D/audio/native resolution

8/2D/PCM/

AC3/720p

Same as above

EDID

Mode

EDID All

8/2D/PCM/1080p

8/2D/PCM/

AC3/1080p

8/2D/PCM/4K2K

8/2D/PCM/

AC3/4K2K

8/2D/PCM/Y420

Same as above

Same as above

Same as above

Same as above

Same as above

8/2D/PCM/AC3/

Y420

Same as above

EDID

Appoint

EDID IN1

EDID IN2

EDID IN3

Input 1’s EDID

Input 2’s EDID

Input 3’s EDID

EDID IN4 Input 4’s EDID

Note:

1. EDID function only selectable under RS-232 and WebGUI control.

2. When power supply is re-plugged from the device the EDID mode will switch to EDID All- HDMI OUTPUT.

9

6.8 Telnet Control

To access the telnet control under MS windows, click ‘Start’ menu and type “cmd” in the search field then press enter.

Under Mac OS X, go to Go → Application → Utilities → Terminal

See below for reference.

Once in the command line interface (CLI) type "telnet", then the IP address, and hit enter.

10

Press “Help” or “?” then hit enter to bring up all available commands.

Note: Any commands will not be executed unless followed by a carriage return. Commands are case-insensitive. If the IP is changed then the IP Address required for Telnet access will also change accordingly.

11

6.9 WebGUI Control

On a PC/Laptop that is connected to an active network system, open a web browser and type device’s IP address (the default statics IP is

192.168.1.50 or available from RS-232 or use the link application from note 4 in section 6.5 to find) on the web address entry bar. The browser will display the device’s Status, IO Status, EDID Control, Settings and

Network Configuration control pages for users to control.

Click on EDID Control for EIDID selections.

Click on Settings to set each input’s HDCP Control and Preset

Configuration. HDCP Enable and Disable equivalence to HDCP standard and Apple mode.

12

Click on Network Configuration to set the device’s IP configuration once the changes is saved the system will reset the IP address on the device automatically and user will need to re-enter the IP address to continue the WebGUI function.

13

7. CONNECTION DIAGRAM

Blu-ray/DVD/PS3 Players

6m

CR-72

INPUT

POWER

5m

6m

30°

1 2

HDMI IN

3 4

HDMI OUT SERVICE CONTROL RS-232 IR IN DC 5V

OR

Display TV/Monitor PC NB

Note: The IR Extender cable distance is up to 5 meters and 8 meters for the IR Window on the front panel.

14

8. SPECIFICATIONS

Frequency bandwidth

Input Ports

ESD Protection

Dimensions

300Mbps to 3Gbps

4 x HDMI, 1 x USB (Service only), 1 x RJ45

(Control), 1 x RS-232, 1 x IR Extender

1 x HDMI

Output ports

Resolution

HDMI I/O Cable Distance 15M@8/12bit, 5M@4Kx2K

IR Frequency

30~50kHz

Power Supply

480i~1080p@50/60, 1080p@24, 4K2K

(3840x2160@24/25/30, 50/60 YUV_420 &

4096x2160@24, 50/60YUV_420)

5VDC/2.6A (US/EU standards, CE/FCC/UL certified)

Human Body model:

± 8kV (air-gap discharge)

± 4kV (contact discharge)

240mm (W) x 104mm (D) x 43mm (H)/

Jacks Excluded

240mm (W) x 111.2mm (D) x 48mm (H)/

Jacks Included

Weight

Chassis Material

Silkscreen Color

Operating Temperature

798g

Metal

Black

0˚C~40˚C / 32˚F ~ 104˚F

Storage temperature

Relative Humidity

Power Consumption

-20˚C~60˚C / -4˚F ~ 140˚F

20~90% RH (no condensation)

4W

15

DVI and HDMI Supported Resolutions

640x480@60

640x480@72

640x480@75

720x480@60

720x576p@50

800x600@60

800x600@72

800x600@75

1024x768@60

1024x768@70

1024x768@75

1280x720@50

1280x720@60

1280x720p@60

1280x768@60

1280x800@60

1280x1024@60

1360x768@60

1600x1200@60

1920x1080i@50

1920x1080i@60

1920x1080p@24

1920x1080p@25

1920x1080p@30

1920x1080p@50

1920x1080p@60

1920x1200@60(RB)

3840x2160@24/25/30, 50/60 Y420

4096x2160@24/,50/60 Y420

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

Output

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

Input

V

V

V

V

V

V

V

16

Audio Sampling Rate Up to 192 kHz

HDMI input (Up to 192kHz)

LPCM 2CH

LPCM 5.1CH

LPCM 7.1CH

Dolby Digital 2~5.1CH/

DTS 2~5.1CH

Dolby TrueHD/

DTS-HD Master Audio

HDMI output

V

V

V

V

V

Audio Format LPCM 2/5.1/7.1CH,Dolby Digital 2~5.1CH, DTS 2~5.1CH

(Pass through), Dolby TrueHD and DTS-HD Master Audio

9. ACRONYMS

ACRONYM

HDCP

HDMI

4Kx2K

COMPLETE TERM

High-bandwidth Digital Content Protection

High Definition Multimedia Interface

3840x2160/ 4096x2160

17

CYPRESS TECHNOLOGY CO., LTD

Home page: http://www.cypress.com.tw

MPM-CPROU4H1HFS