JVC DR-MV2SEU User Guide Manual Operating Instruction Pdf

JVC DR-MV2SEU User Guide Manual Operating Instruction Pdf
DVD VIDEO RECORDER &
VIDEO CASSETTE RECORDER
DR-MV2SEU
STANDBY/ON
OPEN/
CLOSE ON SCREEN SET UP
EJECT
VCR
DVD
[email protected]/:
ABC
DEF
REPEAT
GHI
JKL
MNO
ZOOM
PQRS
TUV
W X YZ
PR
CLEAR
PROG
AUDIO
TIMER
SHOWVIEW
TOP MENU
MENU/LIST
ENTER
RETURN
R
SLOW
PL AY
SLOW
DVD REC
STOP
PAUSE
VCR
VCR REC DUBBING SEARCH
REC
SPEED
VCR
SLOW
REC
VCR
MONITOR SYSTEM
DUBBING
STANDBY/ON
VCR
PR
DVD
VCR/DVD
S-VIDEO VIDEO (MONO) L-AUDIO-R
VCR
DVD
R
RM-SDR057E
LPT1076-014A
INSTRUCTIONS
SHOWVIEW is a registered trademark of
Gemstar Development Corporation.
The SHOWVIEW system is
manufactured under licence from
Gemstar Development Corporation.
???????-????
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
Before You Start
Before You Start
Accessories Supplied
• Remote control with two R6 (AA) batteries
• Instruction Manual
• RF cable
• Scart cable
IMPORTANT
Please read the various precautions on pages 2 to 4 before installing or operating the unit.
Precautions
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
The rating plate and the safety caution are on the rear and the
bottom of the unit.
Laser Safety
Power Supply
This unit employs a laser. Only a qualified service
personnel should remove the cover or attempt to
service this unit, due to the possibility of eye injury.
The power supply is connected and the unit is live
when the mains cable is plugged into a 220–240 V ,
50 Hz AC outlet. To operate the unit, press
[STANDBY/ON /I].
CAUTION:
The mains plug shall remain readily operable.
USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND
INTERLOCK DEFEATED. DO NOT
STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
KLASSE 1 LASER APPARAT
CLASSE 1 PRODUIT LASER
• This unit is classified as a
CLASS 1 LASER product.
• The CLASS 1 LASER
PRODUCT marking is
embossed on the rear cover.
DVD/VCR
AV2(DECODER)
DVD
DIGITAL
AUDIO OUT
ANTENNA
AUDIO
OUT
S-VIDEO
OUT
IN
COAXIAL
L
AV1(TV)
OUT
R
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
2
The lightning flash with
arrowhead symbol, within an
equilateral triangle, is intended
to alert the user to the presence
of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to
persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
WARNING: LIVE PARTS INSIDE.
DO NOT REMOVE ANY SCREWS.
Caution
1. Do not attempt to open the cabinet. There are no
parts inside you can service. Refer all servicing to
qualified service personnel.
2. Slots and openings in the cabinet at the sides and
underneath are provided for ventilation. To ensure
reliable operation and to protect the unit from
overheating, these openings must not be blocked
or covered.
Avoid installation in enclosed spaces such as
bookcases unless suitable ventilation is provided.
3. Keep the unit away from radiators and other heat
sources.
4. Avoid use near strong magnetic fields.
5. Do not push objects of any kind into the unit
through the cabinet slots or openings as they
could touch electrically live parts or short circuit
parts resulting in a fire or electric shock.
6. Do not spill liquid on the unit. If liquid is spilled
and enters the unit, consult qualified service
personnel.
Information for Users on
Disposal of Old Equipment
[European Union]
This symbol indicates that the electrical
and electronic equipment should not be
disposed as general household waste at
its end-of-life. Instead, the product should
be handed over to the applicable
collection point for the recycling of
electrical and electronic equipment for
proper treatment, recovery and recycling
in accordance with your national
legislation.
Attention:
This symbol is
only valid in the
European Union.
By disposing of this product correctly, you
will help to conserve natural resources
and will help prevent potential negative
effects on the environment and human
health which could otherwise be caused
by inappropriate waste handling of this
product. For more information about
collection point and recycling of this
product, please contact your local
municipal office, your household waste
disposal service or the shop where you
purchased the product.
Installation Location
For safety and optimum performance of this unit:
• Install the unit in a horizontal and stable position.
• Do not place anything directly on top of the unit.
• Do not place heavy objects on the unit or remote
control.
• Do not place the unit directly on top of the TV.
• Shield the unit from direct sunlight and keep away
from sources of intense heat. Avoid dusty or humid
locations. Avoid locations with insufficient ventilation
for suitable heat dissipation. Do not block the
ventilation holes on the sides of the unit. Avoid
locations subject to strong vibration or strong
magnetic fields.
Before You Start
7. Do not stand the unit vertically. Use the unit in a
horizontal (flat) position only.
8. Before attempting to operate the unit, make sure
that the timer recording mode is off.
9. This product is in Stand-by mode when turned off
while the mains cable is connected.
10. Do not place any combustible objects on the
device. (Candles, etc.)
11. Before moving the unit, be sure to remove any
discs and unplug the mains cable from the AC
outlet.
Avoid the Hazards of Electrical Shock
and Fire
• Do not handle the mains cable with wet hands.
• Do not pull on the mains cable to disconnect it from
AC outlet. Grasp it by the plug.
• If, by accident, water is spilled on the unit, unplug
the mains cable immediately and take the unit to an
authorized service centre for servicing.
Moisture Condensation Warning
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
after heating a cold room, or under conditions of high
humidity. Do not use the unit for at least 2 hours to
allow the inside to dry.
Penalties may be applicable for incorrect
disposal of this waste, in accordance with
national legislation.
(Business users)
If you wish to dispose of this product,
please visit our web page
www.jvc-europe.com to obtain
information about the take-back of the
product.
[Other Countries outside
the European Union]
If you wish to dispose of this product,
please do so in accordance with
applicable national legislation or other
rules in your country for the treatment of
old electrical and electronic equipment.
Make your contribution to the environment!!!
• Exhausted batteries do not belong in
the dustbin.
• You can dispose of them at a collection
point for exhausted batteries or special
waste.
• Contact your council for details.
For Customer Use:
Carefully read the Model No. and Serial No.
located at the back of the unit and enter the
information below. Retain this information for
future reference.
Model No. _____________________
Serial No. _____________________
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
3
Before You Start
About Copyright
Maintenance
Unauthorized copying, broadcasting, public
performance and lending of discs are prohibited.
This product incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly
is prohibited.
CLEANING THE UNIT
Use a soft cloth slightly moistened with a mild
detergent solution. Do not use solutions containing
alcohol, spirits, ammonia or abrasive.
Manufactured under licence from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
Dolby Digital Recording
“Dolby® Digital Recording enables consumers to
record high-quality video with stereo sound on
recordable DVD discs. The technology, when
utilized instead of PCM recording, also saves
recordable disc space, allowing for higher video
resolution or extended recording time on each
DVD. DVDs created using Dolby Digital Recording
will play back on all DVD-Video players.”
Note: This is true when the players are compatible
with actual recordable DVD discs.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
CLEANING DISCS
If a disc becomes dirty, clean it with a cleaning cloth.
Wipe the disc from the centre out. Do not wipe in a
circular motion.
Do not use solvents such as benzine, thinner,
commercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for
analogue records.
DISC HANDLING
Handle the discs so that fingerprints and dust do not
adhere to the disc surfaces.
Always store the disc in its protective case when it is
not in use.
SERVICING
If the unit becomes inoperative, do not try to correct
the problem by yourself. There are no user
serviceable parts inside. Turn the unit off, unplug the
mains cable, and consult your dealer or an authorized
service centre.
CLEANING THE DISC LENS
If the unit does not perform correctly even though you
have referred to “Troubleshooting” and the relevant
sections in the Instruction Manual, the laser optical
pickup unit may be dirty. Consult your dealer or an
authorized service centre for inspection and cleaning
of the laser optical pickup unit.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted
while the TV programme reception is clear. Dirt
accumulated on the video heads after a long period
of use, or the usage of rental or worn tapes can
cause this problem. If a streaky or snowy picture
appears during playback, the video heads in the unit
may need to be cleaned.
1. Please visit your local Audio / Video store and
purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the
problem, please consult your dealer or an
authorized service centre.
Note:
• Remember to read the instructions along with the
video head cleaner before use.
• Clean video heads only when problems occur.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
4
Editing ...................................................49
Precautions ........................................................... 2
Disc Editing ......................................................... 49
Features ................................................................ 6
Editing Discs in Video Mode ............................... 49
Guide to the Instruction Manual ........................... 7
Editing Discs in VR Mode ................................... 52
Functional Overview.............................................. 8
Editing Original Titles in VR Mode ...................... 52
Installing Batteries in the Remote Control .......... 12
Editing the Playlist in VR Mode .......................... 54
Getting Started
Before You Start..................................... 2
Before You Start
Table of Contents
VCR / DVD Recorder Switching ......................... 12
Guide to On-Screen Displays.............................. 13
Front Panel Display Guide .................................. 16
Changing the Setting Menu .................58
Tour of the Setting Menu ..................................... 58
Language Setting ............................................... 59
Display Setting .................................................... 60
Connections ....................................................... 17
Audio Setting ...................................................... 60
Selecting the On-Screen Display
(OSD) Language ............................................... 19
DVD-Videos Parental Lock Level ....................... 62
Recording
Getting Started ..................................... 17
Changing Video Out System .............................. 63
Channel Setting .................................................. 19
Setting the Clock ................................................ 21
Selecting the TV Aspect Ratio ........................... 22
VCR Functions......................................64
Playback ............................................................. 64
Recording and
One-Touch Timer Recording (OTR) ................... 64
Information on DVD Recording .......................... 23
Search ................................................................ 65
Formatting a Disc ............................................... 25
Other Operations ................................................ 66
Selecting the Sound Mode ................................. 26
Changing the Video Colour System ................... 66
Basic Recording ................................................. 27
Hi-Fi Stereo Sound System ................................ 66
Playing Back
Discs
Recording ............................................. 23
One-Touch Timer Recording (OTR) ................... 28
VPS (Video Programme System) /
PDC (Programme Delivery Control) ................... 31
Settings for External Equipment ......................... 33
Dubbing Mode .................................................... 34
Setting a Disc to Protect .................................... 35
Finalising Discs ................................................. 36
Others ....................................................67
Editing
Timer Recording ................................................ 29
Troubleshooting .................................................. 67
Language Code .................................................. 71
Glossary .............................................................. 72
Specifications ..................................................... 73
Declaration of Conformity ................................... 73
Changing the
Setting Menu
Playing Back Discs .............................. 37
Information on Playing Back DVDs .................... 37
Basic Playback ................................................... 38
PBC Function for Video CDs............................... 40
Special Playback ................................................ 41
VCR Functions
Search................................................................. 44
Repeat / Random / Programme Playback /
Slide Show ......................................................... 45
Selecting the Format of Audio and Video ........... 47
Others
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
5
Before You Start
Features
This unit not only plays back DVDs, CDs and VHS
tapes but also offers features for you to record to DVD
discs and edit them after that. The following features
are offered with this unit.
Recording
VCR mode
Recording up to 8 programmes:
You can programme the unit to record up to 8
programmes, up to a month in advance. Daily or
weekly programme recordings are also possible.
One-touch timer recording:
You can set your required recording time easily. Every
time [DVD/VCR REC I] is pressed during recording,
the recording time will be increased by 30 minutes up
to 8 hours. The recording automatically stops when
the recording time you set is finished.
Dubbing mode:
You can copy a DVD disc to a videotape or copy a
videotape to a DVD disc. This function will be
available only if the DVD disc and the videotape are
not copy protected.
Left channel stereo recording:
The unit can record monaural sound from the Left
channel as pseudo stereo sound (same Left and
Right channels) automatically. (This function is not
available for input source of AV3 jacks on the front
panel.)
DVD mode
REC MONITOR:
You can confirm the picture and sound recording
quality for the recording speed you have currently set.
Automatic Chapter marker setting:
Chapter markers will be added to recordings as you
set them in the Setting menu before starting to record.
Automatic Title menu making (Video mode):
The unit creates title menus automatically when
finalising discs.
Automatic Playlist making (VR mode):
The unit creates a Playlist automatically after
recording.
Automatic finalising (Video mode):
You can finalise discs automatically at the end of the
disc space if you set this in the Setting menu.
Playback
DVD mode
Theatre surround sound:
When the unit is connected to an amplifier or a
decoder compatible with Dolby Digital or DTS, you
can enjoy theatre-quality surround sound from discs
recorded with the surround sound system.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
6
Playback from Original or a Playlist (VR mode):
You can play back titles using either the Original list or
a Playlist.
VCR mode
The unit is compatible with DVD-RW discs, which are
recordable repeatedly, and DVD-R discs, which are
recordable only once.
Also, this unit allows you to record to the video
cassette tape. You can choose either one for your
convenience.
DVD mode
Quick search:
You can easily find the part you want to watch using
the search function. Search for a desired point on a
disc by title, chapter or time.
Quick search for what you want to watch:
You can easily find the part you want to watch using
the Index or Time search functions. An index mark will
be assigned at the beginning of each recording you
make. For Time search function, you can go to a
specific point on a tape by entering the exact amount
of time you wish to skip.
Editing
DVD mode
Set / clear chapter markers (VR mode):
You can easily add chapter markers anywhere in your
recordings for easy editing. (Playlist only)
Making your own Playlist (VR mode):
While the Original list remains unchanged, you can
edit titles as you prefer and create your own Playlist.
Edit title names
Set thumbnail pictures
Set / clear chapter markers
Divide / combine titles
Delete parts of titles
Protecting titles (VR mode):
To avoid accidental editing or erasing of titles, the
protect function is useful when set to “ON” in the
Original list.
Compatibility
DVD mode
VCR mode
VPS / PDC:
This system assures that the TV programme you wish
to record using timer recording will be recorded
exactly from beginning to end even if the actual
broadcasting time differs.
SHOWVIEW ® system:
You can set timer recording using the SHOWVIEW
system by just entering the SHOWVIEW programming
number from a TV guide magazine.
DVD mode
Playing back discs recorded in Video mode on
any regular DVD player:
Discs recorded in Video mode can be played back on
regular DVD players, including computer DVD drives
compatible with DVD-Video playback. You will need to
finalise the discs recorded in Video mode to play back
in other DVD players.
* DVD-Video Format (Video mode) is a new format for
recording on DVD-RW / R discs that was approved by
the DVD Forum in 2000. Adoption of this format is
optional for manufactures of DVD playback devices
and there are DVD-Video players, DVD-ROM drives
and other DVD playback devices available that
cannot play back DVD-RW / R discs recorded in the
DVD-Video Format.
Before You Start
Guide to the Instruction Manual
Symbols Used in the Instruction
Manual
To show what recording mode or disc type applies to
each function, the following symbols appear at the
beginning of each operating item.
Symbol
Description
DVD-V
Video
DVD-RW
VR
DVD-RW
DVD-R
DVD+R
DVD+RW
VD+RW
W
DVD+R
DVD+R
CD
VCD
Available for DVD-Videos
Available for DVD-RW discs in
Video mode
Available for DVD-RW discs in VR mode
Available for DVD-R discs in Video mode
Available for DVD+RW discs*
Available for DVD+R discs*
Available for Audio CDs
Available for Video CDs
MP3
Available for CD-RW / R discs with
MP3 files
JPEG
Available for CD-RW / R discs with JPEG
files
VCR
Available to VHS tapes
Use only cassettes marked VHS. (
PAL
)
* There may be a disc which cannot be used or
played back.
Button Names Described in the
Instruction Manual
The instructions in this manual are described mainly
with the operations using the remote control. Some
operations can be carried out using the buttons on the
front panel.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
7
Before You Start
Functional Overview
Front Panel
2
3* 4
5
DUBBING
STANDBY/ON
PR
VCR
VCR/DVD
DVD
S-VIDEO VIDEO (MONO) L-AUDIO-R
VCR
1
21* 19* 17
22* 20 18
16
DVD
13 12 10*
15 14
11* 9
8 7 6
*You can also turn on the unit by pressing these buttons.
1
STANDBY/ON
/I button
• Press to turn on or off the unit.
* “ ” shows electrical power standby and “I”
shows ON.
2
Cassette compartment (VCR)
• Insert a tape here.
3
Disc tray OPEN/CLOSE O button* (DVD)
• Press to open or close the disc tray.
4
VCR/DVD button (DVD/VCR)
• Press to select the component you wish to
operate.
5
Disc tray (DVD)
• Place a disc here when open.
6
AUDIO input jacks (AV3) (DVD/VCR)
• Use to connect external equipment with
standard Audio cables.
7
VIDEO input jack (AV3) (DVD/VCR)
• Use to connect external equipment with a
standard Video cable.
8
S-VIDEO input jack (AV3) (DVD/VCR)
• Use to connect the S-Video output of external
equipment with an S-Video cable.
9
DVD REC I button (DVD)
• Press once to start a recording.
• Press repeatedly to start a one-touch timer
recording.
10 DVD PLAY P button* (DVD)
• Press to start or resume a playback.
11 DVD STOP S button* (DVD)
• Press to stop a playback or recording.
• Press to stop a timer recording of DVD.
12 DVD light (DVD)
• Lights up when the DVD output mode is
selected.
14 DUBBING button (DVD/VCR)
• Press to start VCR to DVD (DVD to VCR)
duplication which you set in the setting menu.
15 PR(OGRAMME) +/- buttons (DVD/VCR)
• Press up or down to change the channel.
16 Display (DVD/VCR)
• Refer to “Front Panel Display Guide” on
page 16.
17 Remote control sensor
• Receives signals from your remote control so
you can control the unit from a distance.
18 VCR REC I button (VCR)
• Press once to start a recording.
• Press repeatedly to start a one-touch timer
recording.
19 VCR PLAY P button* (VCR)
• Press to start a playback of a video tape.
20 VCR STOP/EJECT S/O button (VCR)
• Press to remove the tape from the unit.
• Press to stop the tape motion.
• Press to stop the proceeding timer recording in
VCR.
21 VCR F.FWD f button* (VCR)
• Press to rapidly advance the video tape.
• Press to view the picture rapidly in forward
during playback. (Forward Search)
• Press to turn the unit on when the video tape is
inserted and start rapidly advancing the tape.
22 VCR REW r button* (VCR)
• Press to rewind the video tape.
• Press to view the picture rapidly in reverse
during the playback mode. (Rewind Search)
• Press to turn the unit on when the video tape is
inserted and start rewinding the tape.
13 VCR light (VCR)
• Lights up when the VCR output mode is
selected.
Button names described in the Instruction Manual
The instructions in this manual are described mainly with the operations using the remote control.
Some operations can be carried out using the buttons on the front panel.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
8
Rear Panel
DVD
DIGITAL
AUDIO OUT
Before You Start
DVD/VCR
AV2(DECODER)
ANTENNA
AUDIO
OUT
S-VIDEO
OUT
IN
L
COAXIAL
AV1(TV)
OUT
R
1
1
Mains cable
2
6
• Connect to a standard AC outlet.
2
AV2 (DECODER) (DVD/VCR)
• Connect to VCR, camcorder, or other AudioVideo equipment. Use a commercially available
Scart cable.
3
AV1 (TV) (DVD/VCR)
• Connect to the Scart jack on your TV. Use the
supplied Scart cable.
4
3
45 6 7 8
S-VIDEO OUT jack (DVD)
• Connect to the S-Video input jack on your TV.
Use a commercially available S-Video cable.
7
ANTENNA IN (DVD/VCR)
• Connect to an antenna or a cable.
8
ANTENNA OUT (DVD/VCR)
• Connect to the Aerial jack on your TV, cable box
or direct broadcast system. Use the supplied RF
cable.
COAXIAL DIGITAL AUDIO OUT jack
(DVD)
• Connect to an amplifier with digital input jacks
such as a Dolby Digital decoder or DTS
decoder. Use a commercially available Coaxial
cable.
5
AUDIO OUT jacks (DVD)
• Connect to the audio input jacks on your TV.
Use commercially available Audio cables.
Note
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage
to the unit.
• This unit does not have an RF modulator.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
9
Remote Control
Before You Start
5
1*
2
3
EJECT
VCR
4
DVD
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
W X YZ
7
8
16
17
18
19
ZOOM
20
PR
9
21
AUDIO
5
6
REPEAT
[email protected]/:
CLEAR
DVD mode
• Press to clear the password once entered.
• Press to cancel the programming for a disc.
• Press to clear the selecting marker number in
the marker setup mode.
• Press to clear the programme once entered in
the timer recording setting mode.
VCR mode
• Press to reset the tape counter.
STANDBY/ON
OPEN/
CLOSE ON SCREEN SET UP
6
PROG
22
23
TIMER
7
8
9
TOP MENU
MENU/LIST
11
12
13
24
7
RETURN
SLOW
PL AY
SLOW
DVD REC
STOP
PAUSE
VCR
VCR REC DUBBING SEARCH
REC
SPEED
TOP MENU button (DVD)
• Press to display the top menu.
ENTER
10
PROG/SHOWVIEW button (DVD/VCR)
• In stop mode, press to set timer recording using
the SHOWVIEW system.
• Press to display the timer programme setting
menu while the SHOWVIEW programming input
display appears.
0
SHOWVIEW
CLEAR button (DVD/VCR)
VCR
SLOW
VCR
REC
MONITOR SYSTEM
14
15
25
26
27*
28
29
30*
31
32
33
8
ENTER button (DVD/VCR)
9
Cursor U / D / L / P buttons (DVD/VCR)
• Press to confirm or select menu items.
• Press to select items or settings.
10
(CM SKIP) button (DVD)
• During playback, press to skip 30 seconds. (See
page 42.)
11 DVD REC I button
• Press once to start a recording.
• Press repeatedly to start a one-touch timer
recording.
• Press to activate the remote control in DVD
mode. (See page 12.)
12 DUBBING button (DVD/VCR)
RM-SDR057E
*You can also turn on the unit by pressing these
buttons when the remote control is in DVD mode.
1
OPEN/CLOSE/EJECT O button* (DVD/
VCR)
• Press to open or close the disc tray.
• Press to remove the tape from the unit.
2
ON SCREEN button (DVD/VCR)
• Press to display the On-Screen display.
3
VCR button
• Press to activate the remote control in VCR
mode. (See page 12.)
• Press to select the VCR output mode.
4
Number buttons (DVD/VCR)
• Press to select channel numbers.
• Press to select a title / chapter / track on the
display.
• Press to enter values for settings in the setting
menu.
• Press to enter the number in the Index or Time
search in VCR mode.
• Press to enter the characters in edit function.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
10
• Press to start VCR to DVD (DVD to VCR)
duplication which you set in the setting menu.
13 VCR REC I button
• Press once to start a recording.
• Press repeatedly to start a one-touch timer
recording.
• Press to activate the remote control in VCR
mode. (See page 12.)
14 REC SPEED button (DVD/VCR)
• Press to switch the recording speed.
15 REC MONITOR button (DVD)
• Press to check the video and audio quality
before attempting to record and during
recording.
16 STANDBY/ON
/I button (DVD/VCR)
• Press to turn on or off the unit.
* “ ” shows electrical power standby and “I”
shows ON.
17 SET UP button (DVD/VCR)
• Press to display the setting menu in stop mode.
18 DVD button
• Press to activate the remote control in DVD
mode. (See page 12.)
• Press to select the DVD output mode.
19 REPEAT button (DVD)
• Press to select the repeat mode.
• During playback, press to enlarge the picture on
the screen.
21 PR(OGRAMME) +/- buttons (DVD/VCR)
DVD mode
• Press to change the channel up or down.
VCR mode
• Press to change the channel up or down.
• Press to adjust the tracking during playback or
in slow motion of the tape.
• While playback is in still mode, you can adjust
the vertically blurred picture.
22 AUDIO button (DVD/VCR)
DVD mode
• When receiving a bilingual broadcast, press to
change the audio out setting to “Main,” “Sub”
and “Main / Sub.”
• Press to change the bilingual audio source of an
external equipment to “Main,” “Sub” and “Main /
Sub.” (Available only when the “External input
Audio” in the DVD setup menu is set to
“Bilingual” in advance.)
• Press to display the audio menu during
playback.
• Press to select the sound mode.
VCR mode
• During playback of a Hi-Fi video tape, press to
change the audio out setting to “STEREO,”
“LEFT,” “RIGHT” and “MONO.”
• When receiving a bilingual broadcast, press to
change the audio out setting to “Main,” “Sub”
and “Main / Sub.”
• Press to change the bilingual audio source of an
external equipment to “Main,” “Sub” and “Main /
Sub.” (Available only when the “External input
Audio” in the DVD setup menu is set to
“Bilingual” in advance.)
23 TIMER
/REV r button (DVD/VCR)
DVD mode
• During playback, press to reverse fast.
• When playback is paused, press to reverse
slowly.
VCR mode
• Press to rewind the video tape.
• Press to view the picture rapidly in reverse
during the playback mode.
SLOW
Before You Start
20 ZOOM button (DVD)
28 SLOW
/FWD f button (DVD/VCR)
DVD mode
• During playback, press to forward fast.
• When playback is paused, press to forward
slowly.
VCR mode
• Press to rapidly advance the video tape.
• Press to view the picture rapidly in forward
during playback.
29 PAUSE p button (DVD/VCR)
• Press to pause a playback or recording.
30 STOP S button* (DVD/VCR)
• Press to stop a playback or recording.
31 VCR SLOW
button (VCR)
• During playback, press to view the videotape in
slow motion.
32 VCR SEARCH button (VCR)
• Press to call up the Index or Time search menu.
33 VCR SYSTEM button (VCR)
• Press to change the video colour system.
Button names described in the Instruction
Manual
The instructions in this manual are described mainly
with the operations using the remote control. Some
operations can be carried out using the buttons on
the front panel.
button (DVD/VCR)
• Press to set the unit in the timer-standby mode.
In the timer-standby mode, press to cancel the
mode and to turn the unit on.
24 MENU/LIST button (DVD)
• Press to display the Disc menu during playback.
• Press to change the Original and Playlist on the
TV screen. (VR mode only)
25 RETURN button (DVD/VCR)
• Press to return to the previously displayed menu
screen.
26 B (SKIP) button (DVD)
• During playback, press to skip to the previous
chapter or track.
• When playback is paused, press to play reverse
step by step.
F (SKIP) button (DVD)
• During playback, press to skip to the next
chapter or track.
• When playback is paused, press to advance
step by step.
27 PLAY P button* (DVD/VCR)
• Press to start or resume a playback.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
11
Before You Start
Installing Batteries in the
Remote Control
Install two R6 (AA) batteries (supplied) into the
remote control, carefully match with the polarity
indicated inside the battery compartment.
1
2
3
VCR / DVD Recorder Switching
Because this product is a combination of a VCR and a
DVD recorder, you must select first which component
you wish to operate with [VCR/DVD] on the front
panel.
DUBBING
STANDBY/ON
PR
VCR
VCR/DVD
DVD
S-VIDEO VIDEO (MONO) L-AUDIO-R
VCR
DVD
VCR/DVD
VCR
Caution
• Incorrect use of batteries can result in hazards such
as leakage and bursting.
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together.
• Make sure that the plus and minus ends of each
battery match the indications inside the battery
compartment.
• Remove batteries if the equipment will not be used
for a month or more.
• When disposing used batteries, please comply with
governmental regulations or the public instructions
for environmental protection that apply in your
country or area.
• Do not recharge, short-circuit, heat, burn or
disassemble batteries.
About the Remote Control
• Make sure there is no obstacle between the remote
control and the remote control sensor on the unit.
• Use within the operating range and angle as shown.
STAN
DBY/
ON
Within about
5m
VCR
DUB
PR
BIN
G
VCR
VCR
/DVD
DVD
DVD
60˚
S-VI
DEO
VIDE
O (MON
O)
L-A
UDIO
-R
SE
R
/:
[email protected]
VC
EN
RE
SC
CT
EJE
/ ON
EN
OP SE
CLO
I
C
GH
AB
2
N
Y/O
NDB
STA
UP
1
T
4
JK
TU
V
R
O
MN
EA
XY
OM
ZO
Z
9
0
DIO
PR
AU
P
TO
ER
TIM
W
VIE
OW
SH
OG
PR
W
6
8
AT
PE
RE
D
5
3
7
DV
L
F
DE
RS
PQ
CL
NU
ME
ST
/LI
NU
ME
R
TE
EN
W
RE
Remote
control
PL
RN
TU
AY
O
SL
OP
Code (DVD): JVC C
Code (VHS): JVC A
• Remote control operation may become unreliable if
the remote control sensor of the unit is being
exposed by the strong sunlight or fluorescent light.
• Remote controls for different devices can interfere
with each other. Be careful when using remote
controls for other equipment located close to the
unit.
• Replace the batteries when the operating range of
the remote control reduces.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
12
DVD
DVD light
VCR light
VCR mode
Press [VCR] on the remote control.
(Verify that the VCR light is lit.)
DVD mode
Press [DVD] on the remote control.
(Verify that the DVD light is lit.)
Note
• Pressing only [VCR/DVD] on the front panel DOES
NOT switch the mode of the remote control. You
MUST select the correct mode on the remote
control.
• Press [VCR/DVD] to select the DVD mode or the
VCR mode.
• You cannot switch to the mode (DVD or VCR) that is
in the timer-standby mode.
• If the media is available, you can start recording by
pressing [DVD REC I] or [VCR REC I] on the
remote control even if another equipment (DVD or
VCR) is selected. In this case, the mode of the
remote control will be automatically switched to the
appropriate component.
Display Menu
Press [VCR] first.
Press [ON SCREEN] to display the On-Screen
display.
DVD mode
Press [DVD] first.
With a disc inserted into the unit, press
[ON SCREEN] to display the On-Screen display. The
menu shows information about what is recorded on
the disc.
3
4
7
6 SP
1
1
1
--:--:--
DVD-RW
P22
Main
SP
6
1:35
5
Disc type and format mode
In some descriptions in this manual, only one type of
disc is indicated as an example.
2
Position number and audio status of the
programme
3
Title number, chapter number and the
time lapse of disc playback
4
Each icon means:
STEREO
4
1
Current time
2
Position number
3
Audio status of the receiving broadcast
or external equipment
4
Audio status of the currently playing
back video tape
5
Tape counter
6
Recording or playing back speed
7
Status of the current tape
This is an example screen for explanation. Displayed
items vary depending on the actual mode.
1
5
1
2
3
This is an example screen for explanation.
Displayed items are depending on the actual
mode.
Video mode
2
0:00:00
12:00
AV2
STEREO
Before You Start
Guide to On-Screen Displays
VCR mode
While in the VCR mode, the On-Screen display of the
VCR mode is displayed.
: Search
: Audio
: Subtitle
: Angle (except VR mode)
: Repeat
: Marker
: Noise Reduction
: Zoom
5
Recording mode and remaining time
6
Status of the current disc
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
13
Advanced Setting Menu:
Setting Menus
Before You Start
Press [SET UP] in stop mode to display “Easy Setting
Menu” or “Advanced Setting Menu.” Choose either
“Easy Setting Menu” or “Advanced Setting Menu”
using [Cursor U / D], then press [ENTER] to
change between the menus.
“Easy Setting Menu” and “Advanced Setting Menu”
are available from the Setting Menu. The “Easy
Setting Menu” consists of the settings frequently
needed, while the “Advanced Setting Menu” consists
of all the settings available. You can set the items
marked with
in the “Easy Setting Menu.”
The unit remembers which setting menu you used
last time and recalls it when you press [SET UP] in
stop mode next time, even if power is switched off.
(i.e., if you use the “Easy Setting Menu” and then turn
the unit off, the “Easy Setting Menu” will appear next
time you turn on the unit and press [SET UP] in stop
mode.)
You can make all the settings available as follows.
Advanced Setting Menu
Playback
Recording
Display
Select Video
Clock
Channel
Disc
Easy Setting Menu
1
Playback:
Set up the unit to play back a disc.
2
Recording:
Set up the unit to record to a disc or a tape.
3
Display:
Easy Setting Menu:
Set up the OSD format and the front panel display of
the unit.
You can make the settings of the basic items as
follows.
4
VCR DVD
Easy Setting Menu
1
2
3
4
5
6
7
OSD Language
English
Clock
Auto Finalise
Disc
OSD Language:
Select the OSD language.
2
Clock:
Set the unit clock.
3
Clock:
Video mode
Timer Programming
Advanced Setting Menu
1
5
Set the unit clock.
Channel
DVD-RW Recording Format
Select Video:
Choose an external input to record from other video
equipment to a disc or a tape.
Channel:
Set up auto tuning or manual tuning.
6
Channel:
Set up and adjust channels.
7
Disc / CD Playback Mode:
“Disc” is available only when a DVD-RW / R disc is
inserted into the unit. If a DVD-Video (commercially
available), a new DVD-R disc or the finalised DVD-R
disc is inserted into the unit, you cannot select “Disc.”
“CD Playback Mode” is available only when an Audio
CD, Video CD or a CD-RW / R disc containing MP3 /
JPEG files is inserted into the unit.
DVD-R & DVD-RW (Video mode)
Disc
4
DVD-RW Recording Format:
Select the DVD-RW recording format between Video
mode and VR mode.
5
Title List
Format
Finalise
Timer Programming:
Programme a timer recording.
6
Auto Finalise:
Set Auto Finalise to “ON” or “OFF.”
7
Disc / CD Playback Mode:
“Disc” is available only when a DVD-RW / R disc is
inserted into the unit. If a DVD-Video (commercially
available), a new DVD-R disc or a finalised DVD-R
disc is inserted into the unit, you cannot select “Disc.”
“CD Playback Mode” is available only when an Audio
CD, Video CD or a CD-RW / R disc containing MP3 /
JPEG files is inserted into the unit.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
14
DVD-RW (VR mode)
Disc
Playlist
Original
Format
Finalise
Disc Protect OFF
ON
CD, MP3, JPEG & Video CD
CD Playback Mode
Before You Start
Random Play
Program Play
PBC(Video CD only)
ON
Slide Show
5 sec.
This is an example screen for explanation. Some
items will be displayed in grey depending on the
inserted disc.
1
Title List / Playlist / Original:
Display the titles recorded on the disc.
2
Format (DVD-RW only):
Erase all of the recorded content on the disc.
• It is not possible to recover erased content. Make
sure before you format a disc.
• It is not possible to use a disc formatted in Video
mode with this unit on other DVD recorders. If you
use the disc on other DVD recorders, reformat the
disc using that DVD recorder.
3
Finalise:
Finalise a disc containing recorded titles.
4
Disc Protect (VR mode only):
Protect a disc from accidental over-recording, editing
or erasing.
5
Random Play:
Activate the random playback feature.
6
Program Play (except MP3 / JPEG files):
Activate the programmed playback feature.
7
PBC (Video CD only):
Turn the PBC function “ON” or “OFF.”
8
Slide Show (JPEG files only):
Select the display time.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
15
Before You Start
Front Panel Display Guide
4
2
1
3
5
1
Current status of the unit
DVD R:
Appears when a DVD-R disc is inserted
into the unit.
DVD RW:
Appears when a DVD-RW disc is inserted
into the unit.
VCR: Appears when the timer recording is
proceeding in VCR.
Appears when VCR is in the timerstandby mode.
Flashes when there is an error in
programming.
VCR→DVD:
Appears during VCR to DVD duplication
process.
VCR←DVD:
Appears during DVD to VCR duplication
process.
p:
Appears when a disc or a tape playback
is paused.
Appears also during step by step
playback.
P:
Appears when playing back a disc or a
tape.
p P : Appears during slow forward or slow
reverse playback.
:
Appears when the timer programming or
one-touch timer recording (OTR) is set
and is operating.
Flashes when all the timer programmes
are finished.
Flashes when there is an error in
programming.
REC: Appears when recording.
Flashes when recording being paused.
REPEAT:
Appears during repeat playback (only for
disc playback.)
: Appears when a tape is in the unit.
2
Disc type and Current status of the unit
CD:
VCD:
DVD:
Appears when an Audio CD or a disc
containing MP3 / JPEG files is inserted
into the unit.
Appears when a Video CD is inserted into
the unit.
Appears when a DVD is inserted into the
unit, or during the timer recording.
Appears when DVD is in the timer-standly
mode.
Flashes when there is an error in
programming.
3
Recording speed
• Selected recording speed appears during
recording or in stop mode.
• Recording speed appears during VCR playback.
4
Title / Track and Chapter mark
:
:
5
Title / track number
Chapter number
Displays the following
•
•
•
•
•
•
•
Playing back time / remaining time
Current title / chapter / track number
Recording time
Clock
Channel number
VCR tape counter
One-touch timer recording (OTR) remaining
time
Display Messages
The disc tray is open.
A disc is inserted into
the unit.
The PBC function of
the Video CD is
activated.
Data is being recorded
on a disc.
The disc tray is closing.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
16
Getting Started
Antenna
To Aerial jack
Cable
Signal
Audio/Video cable (not supplied)
3
or
or
or
Scart/RCA
cable (not
supplied)
3
Scart cable (supplied)
2
Scart adaptor
(not supplied)
DVD/VCR
DVD
DIGITAL
AUDIO OUT
AV2(DECODER)
Getting Started
3
RF cable
(supplied)
ANTENNA
AUDIO
OUT
S-VIDEO
OUT
IN
COAXIAL
1
L
AV1(TV)
OUT
RF cable
(not supplied)
R
3
Connections
Connecting to a TV
Connect the AUDIO OUT jacks of this
unit to the analogue Audio input
jacks of your TV. Use a commercially
available Audio cable.
AUDIO IN
Connect the unit to a TV after considering the
capabilities of your existing equipment.
Audio cable
(not supplied)
Before installation, plug off your TV and this
unit.
Using the Scart jack
S-Video cable
(not supplied)
DVD/VCR
AV2(DECODER)
DVD
DIGITAL
AUDIO OUT
2
3
Connect the antenna or cable to the
ANTENNA IN jack of this unit.
Connect the ANTENNA OUT jack of
this unit to the Aerial jack of your TV.
Use the supplied RF cable.
Connect AV1 (TV) Scart jack of this
unit to the Scart jack of your TV. Use
the supplied Scart cable or a
commercially available Scart / RCA
cable.
Note
• If your TV does not have a Scart jack, use
commercially available Scart adaptor or Scart / RCA
cable to connect. Use only AV1 (TV) or AV2
(DECODER) jack for the VCR output signals of this unit.
Using the S-VIDEO OUT jack and the AUDIO
OUT jacks (only for DVD)
ANTENNA
AUDIO
OUT
S-VIDEO
OUT
IN
COAXIAL
1
S-VIDEO IN
L
AV1(TV)
OUT
R
Note for a TV with no S-Video input jacks or
Scart jack:
• This unit has no RF modulator, so this type of TV
cannot be used.
Connecting to External Equipment
This unit has three input terminals, AV1 or AV2 on the
rear panel and AV3 on the front panel. Be sure that all
the units are off before making connections.
Recording from a DVD player, VCR or other
Audio-Video equipment with a Scart output
jack (AV2)
AV output jack
(Scart)
Scart cable (supplied)
If your TV has an S-Video input jack, use S-Video and
Audio cables to connect.
1
2
Follow steps 1 and 2 above.
Connect S-VIDEO OUT jack of this
unit to the S-Video input jack of your
TV. Use a commercially available
S-Video cable.
Downloaded From DvDPlayer-Manual.com JVC Manuals
AV2 (Rear)
DVD/VCR
AV2(DECODER)
DVD
DIGITAL
AUDIO OUT
ANTENNA
AUDIO
OUT
S-VIDEO
OUT
IN
COAXIAL
L
AV1(TV)
OUT
R
EN
17
Recording from a camcorder or other
Audio-Video equipment with no Scart output
jack (AV3)
If no S-Video input jack is available, connect to
VIDEO input jack on the front panel using an RCA
Video cable.
Change the setup when using S-VIDEO input jack.
(See page 33.)
AV3 (Front)
Getting Started
DUBBING
R
VCR/DVD
• Connecting multi-channel Dolby Digital decoder
allows you to enjoy the 5.1ch Dolby Digital surround
system as well as DTS decoder, 5.1 channel
surround system.
• After connecting to a Dolby Digital decoder, set
“Dolby Digital” to “Stream” in the audio menu. (See
page 61.)
• After connecting to a DTS decoder, set “DTS” to
“ON” in the audio menu. (See page 61.)
• After connecting to a MPEG decoder, set “MPEG” to
“Stream” in the audio menu. (See page 61.)
DVD
S-VIDEO VIDEO (MONO) L-AUDIO-R
VCR
DVD
Connecting to an MD deck or DAT deck
Audio cable
(not supplied)
S-Video cable
(not supplied)
S-VIDEO AUDIO
OUT
OUT
Digital Audio for Better Sound Quality
(Only for DVD)
Dolby Digital decoder,
DTS decoder or
MPEG decoder, etc.
Digital audio
input jack
COAXIAL
COAXIAL
AUDIO
OUT
S-VIDEO
OUT
L
R
Coaxial cable
(not supplied)
DVD/VCR
AV2(DECODER)
DVD
DIGITAL
AUDIO OUT
ANTENNA
AUDIO
OUT
S-VIDEO
OUT
IN
COAXIAL
L
AV1(TV)
OUT
R
The connections illustrated above are
optional for better sound.
1
• The audio source recorded in Dolby Digital 5.1
channel surround format cannot be recorded using
an MD or DAT deck as a digital sound.
• If not connected to a Dolby Digital decoder, set
“Dolby Digital” to “PCM” in the audio menu. Playing
back a DVD using incorrect settings may generate
noise distortion, and damage speakers.
• Set “Dolby Digital,” and “MPEG” to “PCM” and set
“DTS” to “OFF” in the audio menu for connecting to
an MD or DAT deck.
• You can use AUDIO OUT jacks for the connection of
your audio system.
After You Have Completed
Connections
Switch the input selector on your TV to an appropriate
external input channel. For details, refer to the
Instruction Manual of your TV.
Note
DVD
DIGITAL
AUDIO OUT
For clear digital sound quality, use
the COAXIAL DIGITAL AUDIO OUT
jack to connect your digital audio
equipment.
If the audio format of the digital output does not
match the capabilities of your receiver, the
receiver will produce a strong, distorted sound or
no sound at all.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
18
Connecting a Dolby Digital™ decoder, DTS
decoder or MPEG decoder
• Connect this unit directly to the TV. If the Audio/
Video cables are connected to a VCR, pictures may
be distorted due to the effects of the copy protection
system.
Selecting the On-Screen Display
(OSD) Language
1 In stop mode, press [SET UP].
2 If you select “Advanced Setting
Menu,” proceed to step 3.
If you select “Easy Setting Menu,”
proceed to step 4.
Channel Setting
Tuning of this unit to broadcast channels can be
performed in two ways.
Auto Tuning
Programme the tuner to scan only the channels you
can receive in your area.
Press [STANDBY/ON
the unit.
Select “OSD Language” using
[Cursor U / D], then press [ENTER].
2
Turn the TV on and select the input
to which the unit is connected.
Select the appropriate OSD language
using [Cursor U / D], then press
[ENTER].
3
In stop mode, press [SET UP].
Select “Display” using
[Cursor U / D], then press [ENTER].
4
5
OSD Language
VCR DVD
English
English
/I] to turn on
Getting Started
1
3
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
4
Select “Channel” using
[Cursor U / D], then press [ENTER].
5
Select “Auto Tuning” using
[Cursor U / D], then press [ENTER].
Deutsch
The unit will start storing channels available in
your area.
Italiano
Svenska
Nederlands
6
Press [SET UP] to exit.
P 01
Auto Tuning Now
Wait for several minutes to finish channel storing.
6
Press [SET UP] to exit.
You can select only the channels memorized in
this unit by using [PR +/-].
To select a channel
You can select a channel using [PR +/-], or directly
enter the channel using [the Number buttons] on the
remote control.
To cancel auto tuning
Press [RETURN] or [SET UP] during scanning.
Note
• The selection will be affected by how you receive TV
channels in your local area.
• If the auto tuning is cancelled during scanning,
some channels not yet tuned may not be received.
• You cannot change the channel when either VCR or
DVD is in any recording mode (normal recording,
one-touch timer recording or timer recording.)
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
19
• If “Skip” is set to “ON,” select “Skip” using
[Cursor U / D], then press [ENTER]. Select
“OFF” using [Cursor U / D], then press
[RETURN].
• If you want to decode scrambled signals, select
“Decoder” using [Cursor U / D], then press
[ENTER]. Select “ON” using [Cursor U / D],
then press [RETURN].
• To store another channel, repeat steps 4 to 7.
Manual Tuning
Manually tune each channel.
1
In stop mode, press [SET UP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
Getting Started
2
Select “Channel” using
[Cursor U / D], then press [ENTER].
3
Select “Manual Tuning” using
[Cursor U / D], then press [ENTER].
After completion, press [SET UP] to
exit.
To Select a Channel
VCR DVD
Manual Tuning
Position
P01
Channel
12
Decoder
OFF
Skip
ON
4
Select “Position” using
[Cursor U / D], then press [ENTER].
5
Select the position number you wish
to use using [the Number buttons] or
[Cursor U / D], then press
[RETURN].
Notes on using the Number buttons:
• Enter channel numbers as a two-digit number for
the quickest result. For example, to select channel
6, press [0] and [6]. If you only press [6], channel 6
will be selected after 2 seconds. You can only select
channels 1 to 99.
• You can select the external input mode “AV1,” “AV2”
or “AV3.”
• To select “AV1,” press [0], [0], [1].
• To select “AV2,” press [0], [0], [2].
• To select “AV3,” press [0], [0], [3].
To Skip a Preset Channel
You can set the unit to skip channels you can no
longer receive or seldom watch when you access
channels using [PR +/-].
You can select position numbers 01 to 99.
1
6
Select “Channel” using
[Cursor U / D], then press [ENTER].
Follow steps 1 to 3 in “Manual
Tuning.”
2
7
Press [Cursor U / D] to start
scanning.
Select “Position” using
[Cursor U / D], then press [ENTER].
3
Select the position number you wish
to skip using [the Number buttons]
or [Cursor U / D], then press
[RETURN].
4
Select “Skip” using [Cursor U / D],
then press [ENTER].
5
Select “ON” using [Cursor U / D],
then press [RETURN].
• The tuner will begin to search up or down
automatically. When a channel is found, the unit
will stop searching and the picture will appear
on the TV screen.
• You can select a desired channel number using
[the Number buttons]. Refer to the following
Channel Plan table and press the three digits to
select the channel number.
(To select channel 4, press [0] first and then
press [0] and [4]. Or press [4] and then “– – 4”
appears and wait for 2 seconds.)
• If this is the channel you want, press [RETURN].
• To skip another channel, repeat steps 2 to 5.
6
Channel Plan
Ch. Indication
TV Channel
02 - 12
E2 - E12
13 - 20
A - H (only ITALY)
21 - 69
E21 - E69
74 - 78
X, Y, Z, Z+1, Z+2
80 - 99, 100
S1 - S20, GAP
121 - 141
S21 - S41
This unit can receive the Hyper and Oscar
frequency bands.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
20
8
Press [SET UP] to exit.
Move
You can replace two channels.
1
2
Setting the Clock
In stop mode, press [SET UP].
Auto Clock Setting
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
Channel Tuning must be set before setting Auto
Clock.
If it has already appeared, proceed to step 3.
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
Select “Channel” using
[Cursor U / D], then press [ENTER].
4
Select “Move” using [Cursor U / D],
then press [ENTER].
5
Select the position number of which
you want to change the channel
using [Cursor U / D], then press
[ENTER].
In stop mode, press [SET UP].
If it has already appeared, proceed to step 3.
3
Select “Clock” using [Cursor U / D],
then press [ENTER].
Advanced Setting Menu
Playback
Recording
Display
Select Video
You cannot select a position number where
“– – –” appears next to the number, because
“Skip” is set to “ON” for that position number.
6
Move the channel to another
position number using
[Cursor U / D], then press [ENTER].
• To move another channel, repeat steps 5 to 6.
7
Press [SET UP] to exit.
Getting Started
3
1
2
Clock
Clock
Channel
Disc
Easy Setting Menu
4
Select “Auto Clock Setting” using
[Cursor U / D], then press [ENTER].
5
Select “ON” using [Cursor U / D],
then press [ENTER].
The current time will be set automatically.
6
7
Press [SET UP] to exit.
Press [STANDBY/ON
/I] to turn off.
The Auto clock function is activated.
This unit will search for the time only when the
power is off. Leave the unit off for several minutes
to give it time to set the clock.
Hint
• If you want to cancel “Auto Clock Setting,” select
“OFF” using [Cursor U / D], and then press
[ENTER] at step 5.
Note
• The default setting of “Auto Clock Setting” is “OFF.”
• The clock may set itself automatically after you
connect the antenna cable to the unit and plug in the
mains cable. In this case, the current time will
appear on the front panel display.
• To set the clock automatically, the channel assigned
to “P01” must receive the PDC signal.
• The clock cannot be set automatically if you are not
receiving a channel in your area that carries a time
signal. In this case, set the clock manually.
• Once the auto clock setting is performed, the unit
will correct the current time by receiving PDC
broadcasts whenever you turn off the unit.
• The unit will correct the current time automatically at
8:00, if the unit power is turned off.
• Between 23:00 and 1:00, the Auto Clock function
will not operate even if the unit power is turned off.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
21
Manual Clock Setting
1
In stop mode, press [SET UP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
Getting Started
2
Select “Clock” using [Cursor U / D],
then press [ENTER].
3
If you select “Advanced Setting
Menu,” proceed to step 4.
If you select “Easy Setting Menu,”
proceed to step 5.
4
5
Press [ENTER].
Selecting the TV Aspect Ratio
You can select the TV aspect ratio to match the format
of the programme you are playing back with the unit
and that of your TV screen (4:3 standard or 16:9 wide
screen TV.)
1
2
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
If it has already appeared, proceed to step 3.
Press [ENTER] again.
3
Select “Playback” using
[Cursor U / D], then press [ENTER].
4
Select “TV Aspect” using
[Cursor U / D], then press [ENTER].
The default date will appear.
VCR DVD
Clock Setting
In stop mode, press [SET UP].
DVD
Playback
TV Aspect
01 / 01/ 2005(SAT)
0: 00
6
Enter the date (day / month / year)
using [Cursor U / D], then press
[Cursor P].
ALL
All
Disc Menu Language
English
Audio Language
Original
Subtitle Language
OFF
Dynamic Range Control
ON
Fast Forward with Audio
ON
Video Out
5
Select the desired option using
[Cursor U / D], then press [ENTER].
Enter the time (hours / minutes)
using [Cursor U / D], then press
[ENTER].
TV Aspect
DVD
4:3
4:3 Letter
Letter Box
Box
4:3 Pan & Scan
The clock will start.
• Although seconds are not displayed, they will be
counted from zero.
8
Parental Lock
Digital Out
Press [Cursor P] to move the cursor to the next
field. If you wish to go back to the previous field,
press [Cursor L].
7
4:3 Letter Box
16:9 Wide
Press [SET UP] to exit.
Note
• Your clock setting will be lost if either there is a
power failure or the unit is unplugged for more than
30 seconds when the “Auto Clock Setting” is “OFF.”
6
Press [SET UP] to exit.
Hint
If you have a standard TV:
• Select “4:3 Letter Box” for a full width picture
with black bars at the top and bottom.
• Select “4:3 Pan & Scan” for a full height picture
with both sides trimmed.
If you have a wide screen TV:
• Select “16:9 Wide.”
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
22
Recording
Information on DVD Recording
Disc type
Disc format
Functions
Video mode
Playing back,
Limited recording,
Limited editing
Video
DVD-RW
Type of Discs
VR mode
This unit can record on DVD-R and DVD-RW. You
can record on DVD-R only once. On DVD-RW, you
can record and erase many times.
It is possible to record on DVD-R only in Video mode.
DVD-RW can record in the format you select from
Video mode or VR mode.
Logo
VR
DVD-RW
Video mode
DVD-R
Playing back,
Recording, Original /
Playlist editing
Playing back,
Limited recording,
Limited editing
Attributes
If you want to record repeatedly on the same disc, or
if you want to edit the disc after recording, use a
rewritable DVD-RW type disc.
If you want to save recordings without any alteration,
use a non-rewritable DVD-R type disc.
• Discs that should be used with this recorder:
DVD-R: 4x or 8x
DVD-RW: 2x or 4x
• Discs that were tested and proven as compatible
with this recorder:
Maxell DVD-R
TDK DVD-RW 2x
MITSUBISHI DVD-R 8x
JVC DVD-RW 4x
Video mode and VR (Video Recording) mode
Video mode is the same recording format as used on
the pre-recorded DVD-Videos you purchase in local
shops, so you can play back the discs recorded in this
format in most DVD players. You will need to finalise
such discs (see page 36) before playing them back in
other DVD players. Unless finalised, you can record
additional materials or edit discs recorded in Video
mode with this unit.
VR (Video Recording) mode is a basic recording
format for DVD-RW discs. You can record and edit
material repeatedly. It is impossible to record
additional materials on a disc formatted in VR mode
and already recorded in another video system other
than PAL, such as NTSC.
DVD players bearing the
logo are capable
of playing back DVD-RW discs recorded in VR
mode.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Recording
Recording Speed
• 8 cm / 12 cm, single-sided, single layer
disc
• Max. recording time (SEP mode,
approx.):
600 minutes (4.7 GB) (for 12 cm)
180 minutes (1.4 GB) (for 8 cm)
You can select a recording speed from 6 options.
The recording time will vary depending on the
recording speed you select as follows.
Recording speed
Recording time
Video /
Sound
Quality
TV
screen
Front
Panel
Display
12 cm
8 cm
XP
XP
60 min
18 min
Excellent
SP
SP
120 min
36 min
Very good
LP
LP
240 min
72 min
Good
EP
EP
360 min
108 min
Average
SLP
SLP
480 min
144 min
Low
SEP
SEP
600 min
180 min
Low
• This table is intended for a standard new singlesided 12 cm disc. The recording times are estimates
and actual recording time may differ.
• The audio and video quality becomes poorer as the
recording time gets longer.
Restrictions on Recording
You cannot record copy-protected video using this
unit. Copy-protected video includes DVD-Videos and
some satellite broadcasts.
If copy-protected material is detected, recording will
pause or stop automatically and an error message
appears on the screen.
You can only record “Copy-once only” video using a
DVD-RW disc in VR mode with Content Protection for
Recordable Media (CPRM.)
When recording a TV broadcast or an external input,
you can display copy control information on the
screen.
CPRM is a scrambling copy protection system for the
protection of “copy-once” broadcast programmes.
This unit is CPRM compatible, which means that you
can record copy-once broadcast programmes, but
you cannot then make a copy of those recordings.
CPRM recordings can only be played back on DVD
players that are specifically compatible with CPRM.
EN
23
Information on Copy Control
Some satellite broadcasts include copy-protected
information. If you wish to record them, refer to the
following.
Disc type / format
VR
Copy- Copy- Copyfree
once prohibited
ver.1.1 / ver. 1.2
DVD-RW ver.1.1 / ver. 1.2 CPRM compatible
Video
ver.1.1 / ver. 1.2
DVD-RW ver.1.1 / ver. 1.2 CPRM compatible
DVD-R
ver.2.0
Recordable
Not Recordable
Note
Recording
• This unit cannot record on CD-RW or CD-R discs.
• DVD-RW / R and CD-RW / R discs recorded on a
personal computer or a DVD or CD recorder may
not be played back if the disc is damaged or dirty or
if there is condensation on the player’s lens.
• If you record a disc using a personal computer, even
if it is recorded in a compatible format, it may not be
played back because of the settings of the
application software used to create the disc. (Check
with the software publisher for more detailed
information.)
• Discs recorded in Video mode on this unit cannot
record additional information using other DVD
recorders.
• It is not possible to use a disc formatted in Video
mode with this unit on other DVD recorders. If you
use the disc on other DVD recorders, reformat the
disc using that DVD recorder.
• Since recording is performed using the Variable Bit
Rate (VBR) method, the actual remaining time for
recording may be a little shorter than the remaining
time displayed on the OSD, depending on the
picture you are recording.
Making Discs Playable in Other DVD
Players (Finalise)
After recording, you must finalise the disc to play it
back in other players. (See page 36.)
You cannot finalise discs in other DVD recorders.
After finalising
• After DVD-R discs are finalised:
- A title menu is created automatically.
- Undo finalising is not possible.
- Additional recording or editing is not possible.
• After DVD-RW (Video mode) discs are finalised:
- A title menu is created automatically.
- Undo finalising is possible. (See page 36.)
- Additional recording or editing is possible if you
undo finalise. (See page 36.)
• After DVD-RW (VR mode) discs are finalised:
- A title menu is not created.
- Undo finalising is possible. (See page 36.)
- Additional recording or editing is possible even
without undo finalising.
Usable Discs
✬✬✬: Most suitable, ✬✬: Can be used,
✬: Some functions are limited, —: Cannot be used.
Applications
DVD-RW
DVD-R
VR
VIDEO
Record TV programmes
✬✬✬
✬✬✬
✬✬
Reuse by deleting the current
contents
✬✬✬
✬✬
—
Edit the contents
✬✬✬
✬
✬
Edit / Record from external
equipment
✬✬✬
✬✬✬
✬✬✬
Copy discs for distribution
✬✬*
✬✬✬
✬✬✬
Playback on other DVD
equipment
✬✬*
✬✬✬
✬✬✬
Rewritable
Yes
Yes
No
Can create chapters at fixed
intervals (auto)
Yes
Yes
Yes
Can create chapters wherever
you like (manual)
Yes
No
No
Can record 16:9 size pictures
Yes
Yes
Yes
Can record Copy-Once
programmes
Yes
No
No
Can perform basic editing
functions
Yes
Yes
Yes
Can perform advanced editing
functions (Playlist edit)
Yes
No
No
Features
* You can only play back DVD-RW disc recorded in
VR mode on VR-compatible discs.
Note
• For details of the above functions and restrictions,
see the further explanations in this Instruction
Manual.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
24
Setting Auto Chapter
Formatting a Disc
Video
Choosing the Recording Format of a
Blank DVD-RW Disc
Video
VR
DVD-RW
DVD-RW
When inserting a blank disc, the unit automatically
starts to initialise the disc. You can also manually
format a DVD-RW disc once it has been used. After
formatting, you can record on the disc with the
recording format selected in the Setting menu.
1
2
4
5
1
2
In stop mode, press [SET UP].
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
If it has already appeared, proceed to step 3.
In stop mode, press [SET UP].
3
If you select “Advanced Setting
Menu,” proceed to step 3.
If you select “Easy Setting Menu,”
proceed to step 4.
Select “Recording” using
[Cursor U / D], then press [ENTER].
4
Select “Auto Chapter” using
[Cursor U / D], then press [ENTER].
DVDDVD-RW
Recording Format
Auto Chapter
Select “DVD-RW Recording Format”
using [Cursor U / D], then press
[ENTER].
Select “Video mode” or “VR mode”
using [Cursor U / D], then press
[ENTER].
DVD-RW Recording Format
DVD
DVD
Recording
Select “Recording” using
[Cursor U / D], then press [ENTER].
Video mode
Recording
3
VR
DVD-RW
DVD-RW
DVD-R
The unit inserts a chapter mark periodically (every 10
minutes by default) during recording. Using the Auto
Chapter menu, you can set this function off or change
the time period.
10 minutes
Timer Programming
Auto Finalise
5
Video mode
VR mode
mode
VR
Bilingual Recording Audio
Main
External input Audio
Stereo
Dubbing Mode
VCR
DVD
If you wish to set “Auto Chapter” off,
select “OFF” using [Cursor U / D],
then press [ENTER].
Auto Chapter
DVD
OFF
OFF
Video mode
DVD Player Compatibility mode.
VR mode
Editing possibility mode.
55minutes
minutes
10 minutes
15 minutes
30 minutes
60 minutes
6
Press [SET UP] to exit.
Note
• The recording format setting is effective only for
DVD-RW discs. You cannot change the recording
format for a DVD-R disc. DVD-R discs are always in
Video mode.
• You cannot mix two formats on one DVD-RW disc.
If you insert a disc that has been recorded before,
the recording format cannot be changed even if you
change it in the Setting menu.
• If a blank DVD+R or DVD+RW disc is inserted, the
error message (“Disc Error”) will appear.
• A Playlist is created automatically during recording
on a DVD-RW disc in VR mode.
Downloaded From DvDPlayer-Manual.com JVC Manuals
If you wish to change the time period
for Auto Chapter, select the required
time period using [Cursor U / D],
then press [ENTER].
6
Press [SET UP] to exit.
EN
25
Reformatting a Disc Manually
Video
VR
DVD-RW
DVD-RW
If you are using a DVD-RW disc, you can format the
disc by performing “Format.” By default it will be in
Video mode. You can change this to VR mode using
the Setting menu.
Note
Selecting the Sound Mode
This unit can receive bilingual broadcasts.
You can switch between modes by pressing [AUDIO]
on the remote control. Each mode is indicated on the
TV screen as follows.
• During reception of bilingual broadcasts
Mode
• When you reformat the disc, the contents of the disc
are erased.
Insert a recordable disc.
1
In stop mode, press [SET UP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
Recording
2
Select “Disc” using [Cursor U / D],
then press [ENTER].
3
Select “Format” using
[Cursor U / D], then press [ENTER].
4
Select “Yes” using [Cursor U / D],
then press [ENTER].
Display on the
TV screen
Audio output
Main
Main audio from both
speakers
Main
Sub
Sub audio from both
speakers
Sub
Main / Sub
• Main audio from the left
speaker
• Sub audio from the
right speaker
Main / Sub
Setting External Input Audio
Video
VR
DVD-RW
DVD-RW
DVD-R
When the external input audio is a bilingual
broadcast, or when copying a video tape to a DVD
disc, you can choose “Stereo” or “Bilingual” to record
on a DVD.
Format
1
2
Yes
No
Are you sure?
Yes
No
In stop mode, press [SET UP].
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
If it has already appeared, proceed to step 3.
A popup window will appear and prompt you to
confirm.
If you want to cancel formatting, select “No.”
5
Select “Yes” using [Cursor U / D],
then press [ENTER].
Formatting will start.
If you want to cancel formatting, select “No.”
6
Formatting is complete.
100% is indicated.
Note
• It is not possible to use a disc formatted in Video
mode with this unit on other DVD recorders. If you
use the disc on other DVD recorders, reformat the
disc using that DVD recorder.
• You cannot cancel formatting once it has started.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
26
3
Select “Recording” using
[Cursor U / D], then press [ENTER].
4
Select “External input Audio” using
[Cursor U / D], then press [ENTER].
Recording
DVD
DVD-RW Recording Format
Video mode
Auto Chapter
10 minutes
Timer Programming
Auto Finalise
Bilingual Recording Audio
Main
External input Audio
Stereo
Dubbing Mode
VCR
DVD
5
Select “Stereo” or “Bilingual” using
[Cursor U / D], then press [ENTER].
External input Audio
DVD
Stereo
Bilingual
Note
• If you are recording onto a VR mode disc, both
“Main” and “Sub” will be recorded regardless of your
setting here. And when you play back, you can
choose either audio format or a combination of both
as your playback audio.
Basic Recording
Video
VR
DVD-RW
DVD-RW
DVD-R
Follow the steps below to record a TV programme.
6
Press [SET UP] to exit.
1
Hint
• If you select “Stereo”:
The audio will be recorded as “stereo audio.”
Make sure that the TV input is set on the unit.
This operation may take a few moments to
complete.
2
3
Setting Bilingual Recording Audio
Recording
• If you select “Bilingual”:
The audio will be recorded as “bilingual audio”
(see next section for more detail).
Turn on the unit and insert a
recordable disc.
Press [DVD].
Select the recording speed using
[REC SPEED]. (See page 23.)
Make sure that the recording format is set to the
desired mode. (See page 25.)
Video
DVD-RW
DVD-R
You can select either “Main” or “Sub” audio to record a
bilingual broadcast in Video mode.
4
1
2
Select the desired channel to record
using [PR +/-] or [the Number
buttons].
5
Press [DVD REC I] to start
recording.
In stop mode, press [SET UP].
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
The ● mark will be displayed for 5 seconds.
To pause the recording, press [PAUSE p]. Press
[DVD REC I], or press [PAUSE p] again to
restart the recording.
If it has already appeared, proceed to step 3.
3
Select “Recording” using
[Cursor U / D], then press [ENTER].
4
Select “Bilingual Recording Audio”
using [Cursor U / D], then press
[ENTER].
5
Select “Main” or “Sub” using
[Cursor U / D], then press [ENTER].
Bilingual Recording Audio
DVD
Main
Sub
6
Press [SET UP] to exit.
Downloaded From DvDPlayer-Manual.com JVC Manuals
6
Press [STOP S] to stop the
recording.
This operation may take a few moments to
complete.
Hint
• You can change the channel while in the REC pause
mode.
Note
• Recording starts immediately and continues until the
disc is full or you stop recording.
• If the clock is not set, the date and time space next
to title names in the Original or Playlist will be blank.
• You cannot mix two formats on DVD-RW discs. If
you insert a previously recorded disc, changing the
recording format is not possible even if you change
it in the Setting menu.
• You cannot change the recording speed while in the
REC or REC pause mode.
• It is possible to record video only in the PAL system.
EN
27
Checking the Recording Picture and
Sound Quality
Video
VR
DVD-RW
DVD-RW
DVD-R
Before recording on a DVD, you can confirm the
quality of the picture and sound with the recording
speed you selected.
1
2
Press [REC MONITOR].
Recording
• If you want to change the recording speed (to
improve the recording quality), press
[REC SPEED] repeatedly.
The recording speed is changed each time you
press the button.
XP
SP
LP
EP
SLP
SEP
• You cannot change the recording speed during
recording.
Press [REC MONITOR] again to exit.
Hint
• If you press [REC MONITOR] while receiving the
bilingual broadcast, the sound to be recorded will be
output.
One-Touch Timer Recording
(OTR)
Video
VR
DVD-RW
DVD-RW
DVD-R
This is a simple way to set the recording time in
blocks of 30 minutes. Check that the disc you are
recording onto has enough space remaining for the
time you set.
1
Turn on the unit and insert a
recordable disc.
Make sure that the TV input is set on the unit.
2
3
Press [DVD].
Select the recording speed using
[REC SPEED]. (See page 23.)
Make sure that the recording format is set to the
desired mode. (See page 25.)
4
Select the desired channel to record
using [PR +/-] or [the Number
buttons].
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
28
Press [DVD REC I] repeatedly until
the desired recording time (30
minutes to 8 hours) appears on the
TV screen.
One-touch timer recording will start.
0:30
(Normal Recording)
Make sure that the unit is in STOP or
REC mode and a DVD is inserted
correctly.
The TV will display the programme and output the
sound you are about to record in the quality of the
picture and sound (determined by the recording
speed) you selected.
3
5
8:00
1:00
7:30
• To change the recording length during onetouch timer recording, press [DVD REC I]
repeatedly until the desired length appears.
• To cancel one-touch timer recording within the
specified time, press [STOP S].
Hint
• The remaining recording time will appear on the TV
screen during one-touch timer recording. Press
[ON SCREEN] to see it on the TV screen.
• The remaining recording time will be displayed on
the front panel display during one-touch timer
recording.
• Unlike timer recording, you can perform the
following operations during one-touch timer
recording.
- Turn off the power.
- Use [DVD REC I] or [STOP S].
Note
• You cannot use the pause function during one-touch
timer recording.
• The unit will be turned off automatically under the
following conditions.
- No space remains on the disc.
- If a power failure occurs.
• If DVD one-touch timer recording is completed
during VCR playback or recording, the DVD will be
in stop mode and the VCR keeps the current mode.
• When an OTR finishes, the unit automatically turns
itself off. If there is any timer recording in standby,
the unit automatically switches to the timer-standby
] to cancel the timermode. Press [TIMER
standby mode to use the unit continuously.
7
Enter the time to start and to end
using [Cursor U / D], then press
[Cursor P].
8
Select the channel number to record
using [Cursor U / D], then press
[Cursor P].
Timer Recording
Video
VR
VCR
DVD-RW
DVD-RW
DVD-R
You can set the unit to record up to 8 programmes, up
to a month in advance. Daily or weekly programme
recordings are also available.
• Be sure to set the clock before entering a timer
programming.
• You can select the timer programming list by
pressing [PROG] twice. In this case, continue from
step 5.
Insert a recordable disc or a tape with a
record tab.
1
2
In stop mode, press [SET UP].
3
Select “Recording” using
[Cursor U / D], then press [ENTER].
4
Select “Timer Programming” using
[Cursor U / D], then press [ENTER].
The Timer Programming list will appear.
5
Select a programme that is not set
using [Cursor U / D], then press
[ENTER].
9
Select the recording media (“DVD”
or “VCR”) using [Cursor U / D], then
press [Cursor P].
10 Select the recording speed using
[Cursor U / D], then press
[Cursor P]. (Refer to “Recording Speed” on
page 23 for DVD or page 64 for VCR.)
11 Select VPS / PDC “ON” or “OFF”
using [Cursor U / D]. (See page 31.)
12 Press [ENTER] when all information
required is entered.
Your programme setting is stored.
• To set another programme, repeat steps 5 to 12.
• To exit, press [SET UP] or [PROG].
• If the recording times of two or more
programmes overlap, “Overlap” and overlapped
programme numbers are displayed. (See pages
30 and 32.)
Date
Start
End
Date
Start
End
End
1. -—-—
-—
7. - - -
4. - - -
8. - - -
5. - - -
Enter the date using [Cursor U / D],
then press [Cursor P].
Each time you press [Cursor D] at the current
date, the timer recording mode will change as
follows.
e.g., 1st January
01/01
Daily
M-F (Mon.-Fri.)
W-SAT
W-FRI
W-SUN
31/01
Downloaded From DvDPlayer-Manual.com JVC Manuals
ON
6. - - -
3. - - -
6
XP
5. - - -
2. - - -
8. - - -
VPS
Speed PDC
4. - - -
VCR
7. - - -
P01 DVD
3. - - -
VPS
CH DVD
Speed
CH
Speed PDC
6. - - -
CH
DVD
VCR
2. - - -
VCR DVD
Timer Programming
VCR DVD
Timer Programming
1. 01/01 12:00 13:00
Recording
If you select “Advanced Setting
Menu,” proceed to step 3.
If you select “Easy Setting Menu,”
proceed to step 4.
To record from external input, select “AV1,” “AV2”
or “AV3.”
13 Press [TIMER
].
The
icon will appear on the front panel display
and the unit enters to the timer-standby mode.
Note
• If you have not set the clock, the clock setting
window will appear after step 4. Continue from step
5 in “Manual Clock Setting” on page 22 before
programming the timer.
• Press [Cursor L / P] to move the cursor in the timer
programming menu.
• If a basic recording or one-touch timer recording is
in progress on one component (e.g. VCR) and the
timer recording set for the other component (e.g.
DVD) is about to begin, the unit automatically
switches to the programmed channel for timer
recording 2 minutes before the programmed starting
time, and the recording in progress (for VCR) will be
cancelled UNLESS their recording channels are the
same. If their recording channels are the same, the
timer recording will start without cancelling the
recording currently in progress. In this case, the
recording of the same channel will be made on both
DVD and VCR.
EN
29
• Cancel the timer-standby mode by pressing
] before operation for either DVD or
[TIMER
VCR. When finished operating, press [TIMER
to resume the timer-standby mode.
Note
]
If VPS / PDC is “ON”:
• In the timer-standby mode, you can neither turn on
the power nor use the component (VCR or DVD)
which is not currently timer-programmed.
If VPS / PDC is “OFF”:
• In the timer-standby mode, you can turn on the
power and use the component (VCR or DVD) which
is not currently timer-programmed.
Checking, Cancelling, or Correcting
the Timer Programming Information
Recording
In the following example, No. 5 timer programming
overlaps on No. 1 and No. 6 timer programmes. In
such a case, you should correct the programme time
to clear the overlap.
VCR DVD
Timer Programming
Start
End
1. 01/01 12:00
Date
13:00
CH
DVD
VCR
AV3 DVD
4. - - -
To Stop the Timer Recording in
Progress
On the front panel of the unit, press
[DVD STOP S] to stop the disc
recording or [VCR STOP/EJECT S/O] to
stop the tape recording.
Note
• [STOP S] on the remote control is not effective.
Speed VPS
PDC
XP
ON
2. - - 3. - - -
• If a timer recording is proceeding, that programme is
highlighted in red. In such a case, you cannot select
any other programmes.
• When you check the timer programming in progress
by pressing [PROG] during operations of the
component (DVD or VCR) which is not currently
used for the timer recording, the programme will not
be highlighted. In this case, you cannot select other
programmings.
Overlap
No.1 6
5. 01/01 12:30
14:00
P02
VCR
SP
OFF
6. 01/01 13:45
21:00
P12
DVD
SEP
OFF
If the Timer Programming Did Not
Complete Correctly
The error number appears on the timer programming
list.
7. - - 8. - - -
1
2
Press [TIMER ] so that the
icon
disappears from the front panel
display.
Press [PROG] twice.
Timer programming list will appear.
3
Check the information on the list you
will need.
4
To clear the timer programming,
select the desired programme using
[Cursor U / D], then press [CLEAR].
To correct the timer programming
1) Select the desired programme using
[Cursor U / D], then press [ENTER].
2) Correct the timer programming using
[Cursor U / D / L / P].
3) Press [ENTER] again.
5
6
Press [PROG] to exit.
Press [TIMER ] to return to the
timer-standby mode.
To check the timer programming in progress
Press [PROG].
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
30
VCR DVD
Timer Programming
Date
Start
Start
End
End
1. 01/01 12:00 13:00
VPS
CH DVD
Speed
CH
Speed PDC
VCR
AV3 DVD
E1
ON
2. - - 3. - - 4. - - 5. - - 6. - - 7. - - 8. - - -
The error programme will be displayed in grey
with an asterisk and have an error number.
The error numbers indicate:
E1–E22, E37–E39: Recording error
E23–E24: Unrecordable disc
E25:•Copy prohibited programme
•Cannot record because of the NTSC / PAL60 signal is received.
E26–E28: Copy prohibited programme
E29: Disc protected
E30: Disc full
E31: Already recorded 99 titles (Video mode)
E32: Already recorded 99 titles (VR mode)
E33: Already recorded 999 chapters
E34: No space for Control Information
E35: PCA (Power Calibration Area) full
E36: Already finalised Video format disc
E40:•There are some unrecorded parts due the
overlapped timer programmes.
•Recording did not start at the start time.
•There is no tape in the cassette
compartment.
•Tape recording reaches to the tape end
during timer recording.
E41: Power failure
E42: No disc
The error programme will be deleted once you
check the error in the programme list, or once you
cancel the timer-standby mode and re-enter it.
2
Press [CLEAR] to erase the selected
programme.
Set the SHOWVIEW programming
number of the programme you want
to record using [the Number
buttons], then press [ENTER].
ShowView System
Please enter a ShowView No.
VPS (Video Programme System)
/ PDC (Programme Delivery
Control)
3
Select the desired recording pattern
using [Cursor U / D], then press
[ENTER].
ShowView System
Once
Recording
The Video Programme System (VPS) or Programme
Delivery Control (PDC) assures that the TV
programmes you have programmed for timer
recording are recorded exactly from beginning to end,
even if the actual broadcasting time differs from the
scheduled time due to a delayed start or extension of
the programme duration. Furthermore, if a
programme is interrupted, the recording will also be
interrupted automatically and resumed when the
programme starts again.
- - - - - - - - -
Daily
M-F
If the VPS / PDC signal drops out because the
broadcast signal is weak, or if a broadcasting station
does not transmit a regular VPS / PDC signal, the
timer recording is performed in normal mode (without
VPS / PDC) even if it was programmed for VPS /
PDC. If the starting time of the VPS / PDC timer
recording is between 0:00 and 3:59 on a given day,
the VPS / PDC function will operate from 20:00 on the
previous day to 4:00 on the given day. If the starting
time of the VPS / PDC timer recording is between
4:00 and 23:59 on a given day, the VPS / PDC
function will operate from 0:00 on the day to 4:00 on
the given day. This means that if the relevant
programme is broadcasted within this period, it is
recorded correctly. If the timer is not programmed
correctly, the incorrect timer setting stays in effect
unless you cancel it. To cancel an incorrect timer
setting, refer to “Checking, Cancelling, or Correcting
the Timer Programming Information” on page 30.
Weekly
Once: To record a TV programme once, as you
set.
Daily: To record a TV programme at the same
time on the same channel everyday.
M-F: To record a TV programme at the same time
on the same channel from Monday through
Friday.
Weekly: To record a TV programme at the same
time on the same channel every week.
4
Select a recording channel using
[Cursor U / D], then press
[Cursor P].
Timer Recording Using
the SHOWVIEW® System
You can programme the timer using the SHOWVIEW
programming numbers that are printed in your local
TV guide magazine.
1
In stop mode, press
[the SHOWVIEW button].
• If the Timer Programming list is full, the Timer
Programming mode is activated instead of the
SHOWVIEW programming mode.
• Press [the SHOWVIEW button] again in the
SHOWVIEW programming mode to switch to the
Timer Programming mode.
Downloaded From DvDPlayer-Manual.com JVC Manuals
VCR DVD
Timer Programming
Date
1. Daily
Start
7:30
End
CH
14:15 P08
DVD
VCR
DVD
VPS
Speed PDC
LP
OFF
2. - - 3. - - 4. - - 5. - - 6. - - 7. - - 8. - - -
• If your local channel information is programmed
in the unit’s memory, your local channel number
appears automatically.
• If your local channel information is not
programmed in the unit’s memory, “P– –” may
appear.
• If you select the channel number using
[Cursor U / D], it is stored in the unit’s
memory.
EN
31
5
Select the recording media (“DVD”
or “VCR”) using [Cursor U / D], then
press [Cursor P].
6
Select a recording speed using
[Cursor U / D], then press
[Cursor P].
7
Select VPS / PDC “ON” or “OFF”
using [Cursor U / D], then press
[ENTER]. (See page 31.)
8
Press [SET UP] or
[the SHOWVIEW button] to exit.
9
Press [TIMER
].
The
icon will appear on the front panel display
and the unit enters to the timer-standby mode.
Recording
Note
• If you have not set the clock, the clock setting
window will appear after step 1. Continue from step
5 in “Manual Clock Setting” before programming the
timer. (See page 22.)
• If the SHOWVIEW programming number is not
available, “Code Error” is displayed and the number
will clear when you press [ENTER] in step 2.
• If the SHOWVIEW programming number previously
set overlaps with the one you entered and the
channel is different, “Overlap” is displayed but the
timer programming will be cleared when you press
[ENTER] in step 3.
• If you enter the same SHOWVIEW programming
number and the recording pattern which you have
already entered, the previously set programme will
be overwritten.
• If you enter the same SHOWVIEW programming
number but a different recording pattern, it will be
saved as a new programme and added to the timer
programming list.
“Code Error” is displayed if:
• A past time is entered for start and end times.
• The SHOWVIEW programming number cannot be
decoded.
“Overlap” is displayed if:
• There is an overlap with a timer recording
setting in different channels.
Hints for Timer Recording
• If there is a power failure or the unit is unplugged for
more than 30 seconds, the clock setting and all
timer settings will be lost.
• If there is no disc or an unrecordable disc in the tray,
the DVD indicator on the front panel display will
flash and timer recording will not occur. Insert a
recordable disc.
• If there is no tape or a tape with a record tab is not in
the cassette compartment, the VCR indicator on the
front panel display flashes and timer recording
cannot be performed. Please insert a recordable
tape.
• When all timer recordings are complete, the
icon flashes. To play back or eject the recorded disc,
press [TIMER
], and then press [PLAY P] or
[OPEN/CLOSE/EJECT O].
• The timer recording cannot be performed in DVD
and VCR at the same time. If you set two
programmings with the same channel and time both
in DVD and VCR, the programming that has priority
will be recorded.
• You cannot make any DVD operation during DVD
timer recording.
• You cannot make any VCR operation during VCR
timer recording.
• If the Start and End times are same, the length of
the recording will be set for 24 hours. If the disc
becomes full during recording, the unit will turn itself
off. To continue recording, press [TIMER
] to
cancel the timer-standby mode, insert a recordable
disc and press [TIMER
] again.
• If two or more programmes overlap, “Overlap” and
the overlapped programme number will appear on
the display.
• If the Start time is earlier and the End time is later
than the current time, the recording will start
immediately after you press [TIMER
].
• If a videotape ends during timer recording, the unit
will automatically stop, eject the videotape, and turn
itself off. To continue recording, insert a recordable
tape.
Priority of overlapped settings
The unit records programmes according to priority if
timer programmes overlap.
If the starting time is same:
• The timer programming set first (PROG. 1) has
priority.
PROG. 1
PROG. 2
Actual
recording
PROG. 1
PROG. 2
recording
will start
after
PROG. 1
recording is
PROG. 2 completed.
Additional 30 seconds (at the most) are cut off.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
32
If programming has been made at the end of the
programming (PROG. 1) currently being recorded:
• The timer programming set first (PROG. 2) has
priority. PROG. 3 will not be recorded.
PROG. 1
PROG. 2
PROG. 3
Actual
recording
PROG. 1
PROG. 2
PROG. 2
recording
will start
after
PROG. 1
recording is
completed.
Additional 30 seconds (at the most) are cut off.
If the recording time is partially overlapped:
• The timer programming with the earlier start time
(PROG. 2) has priority. PROG. 1 will start after
PROG. 2 recording is complete.
PROG. 1
PROG. 2
PROG. 2
PROG. 1
Connection to External Equipment
Video
1
2
Additional 30 seconds (at the most) are cut off.
If the recording time entirely overlaps:
• The shorter timer programming (PROG. 1) is not
recorded.
PROG. 1
PROG. 2
Actual
recording
PROG. 2
VR
VCR
DVD-RW
DVD-RW
DVD-R
Connect the external equipment using either the input
jacks, AV1, AV2 (Rear) or AV3 (Front). However, for
AV3 jacks, you have to select S-VIDEO input or
VIDEO input jacks depending on the connected
devices.
Use commercially available Scart, S-Video or Video
cable and an Audio cable for this connection.
In stop mode, press [SET UP].
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
If it has already appeared, proceed to step 3.
3
Select “Select Video” using
[Cursor U / D], then press [ENTER].
4
5
Press [ENTER].
Note for DVD recording
• If the recording time of two programmes overlap, or
the End time of a programme and the Start time of
another is same, the first 30 seconds (at the most)
of the subsequent programme are cut off.
Recording
Actual
recording
Settings for External Equipment
Select the input jack type to be used
using [Cursor U / D], then press
[ENTER].
AV3 (Front)
VCR DVD
Video In
S-Video In
If the End time of the programme currently being
recorded and the Start time of the subsequent
programme are same:
• If PROG. 1 is a DVD recorded programme, the
beginning of PROG. 2 may be cut off.
PROG. 1
• If you want to use VIDEO input jack (Composite),
select “Video In.”
• If you want to use S-VIDEO input jack, select
“S-Video In.”
PROG. 2
Actual
recording
PROG. 1
PROG. 2
The first 30 seconds
(at the most) are cut off.*
* If the cut off time exceeds 1 minute, the error
number “E40” will appear in the timer programming
list.
Downloaded From DvDPlayer-Manual.com JVC Manuals
6
Press [SET UP] to exit.
EN
33
Recording from External Equipment
Video
VR
VCR
DVD-RW
DVD-RW
DVD-R
Before recording from external equipment, see page
17 for connection instructions.
1
Turn the TV and the unit on, and
select the input of the TV to which
the unit is connected.
2
When you want to record to the disc:
Press [DVD].
Press [OPEN/CLOSE/EJECT O] to
open the disc tray, then place the
disc to record on.
Press [OPEN/CLOSE/EJECT O]
again to close the disc tray.
Recording
When you want to record to a tape:
Press [VCR].
Insert the tape with a record tab into
the cassette compartment.
3
Select the input terminal to which the
external equipment is connected.
(AV1, AV2 or AV3)
To use the input jacks on the back of the unit,
select the “AV1” or “AV2” position by pressing [0],
[0], [1] or [0], [0], [2] on the remote control or
using [PR +/-].
To use the input jacks on the front of this unit,
select “AV3” position by pressing [0], [0], [3] on
the remote control or using [PR +/-].
4
Select a recording speed using
[REC SPEED]. (Refer to “Recording Speed”
Dubbing Mode
Video
Note for recording to a tape:
• The tape’s record tab is intact.
• The videotape is long enough to record the DVD
disc.
Note for recording to a disc:
• The DVD disc is satisfied with the recording status.
See pages 23 and 24.
Insert a disc and a tape with a record
tab.
1
2
For disc:
Press [DVD REC I] on the unit to
start recording.
For tape:
Press [VCR REC I] on the unit to
start recording.
6
Press the PLAY button on the
external recording component.
7
For disc:
Press [DVD STOPS] on the unit to
stop recording.
For tape:
Press [VCR STOP/EJECT S/O] on
the unit to stop recording.
Note
• During recording, if a signal other than PAL is
detected (such as NTSC), recording is paused.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
34
In stop mode, press [SET UP].
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
It has already appeared, proceed to step 3.
3
Select “Recording” using
[Cursor U / D], then press [ENTER].
4
Select “Dubbing Mode” using
[Cursor U / D / L / P], then press
[ENTER].
on page 23 for DVD or page 64 for VCR.)
5
VR
VCR
DVD-RW
DVD-RW
DVD-R
You can copy a DVD disc to a videotape or copy a
videotape to a DVD disc. This function will be
available only if the DVD disc or the tape is not copy
protected. Before starting this function, prepare for the
recording on the DVD-R / RW disc or the videotape.
See pages 23 and 64.
Option window will appear.
VCR to DVD
5
Select “VCR→DVD” using
[Cursor U / D], then press [ENTER].
Dubbing Mode
VCR
DVD
DVD
VCR
VCR DVD
6
Press [SET UP] to exit the setting
menu.
7
Press [DVD].
Make sure to select a recording speed using
[REC SPEED]. (See page 23.)
8
Press [VCR].
9
Press [VCR PLAY P] on the unit, and
then press [PAUSE p] at the point
you wish to start recording.
10 Press [DUBBING].
VCR to DVD duplication will start.
11 Press [STOP S] to stop the
recording.
DVD to VCR
5
Select “DVD→VCR” using
[Cursor U / D], then press [ENTER].
Dubbing Mode
VCR
DVD
DVD
VCR
VCR DVD
recording.
Note
• When you turn off the unit after setting the Dubbing
Mode to DVD→VCR, the setting will be set to
VCR→DVD automatically.
• Dubbing Mode is available only if the tape or disc is
not copy protected.
• You cannot change the output mode during VCR to
DVD or DVD to VCR duplication.
Setting a Disc to Protect
VR
DVD-RW
To prevent accidental over-recording, editing or
erasing of recordings, you can protect them using the
Setting menu.
Insert a recordable disc.
1
In stop mode, press [SET UP].
Recording
Note For VCR to DVD duplication:
• After starting VCR to DVD duplication, the picture
may be distorted because of the auto tracking
function. This is not a malfunction. Be advised to
play back the tape until the picture is stabilized, then
set the starting point which you wish to start
recording, and start VCR to DVD duplication.
• If the playback sound mode of VCR is set to
“STEREO,” “LEFT” or “RIGHT,” the sound mode
upon dubbing is automatically switched to
“STEREO.” If the playback sound mode is set to
“MONO,” the sound mode upon dubbing is also
“MONO.”
• If you set “External input Audio” to “Stereo,” the
sound is recorded in “Stereo” (both Video mode and
VR mode.)
• While in video mode, if you set “External input
Audio” to “Bilingual,” “Bilingual Recording Audio”
mode is recorded.
While in VR mode, if you set “External input Audio”
to “Bilingual,” bilingual audio is recorded.
• The main and sub audio will be simultaneously
recorded (VR mode.) You can select audio modes
during playback.
11 Press [STOP S] to stop the
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
2
Select “Disc” using [Cursor U / D],
then press [ENTER].
3
Select “Disc Protect OFF → ON”
using [Cursor U / D], then press
[ENTER].
4
Select “Yes” using [Cursor U / D],
then press [ENTER].
The disc is protected.
Note
• The Disc Protect setting is available only when a
disc recorded in VR mode is inserted.
• You can select only “Disc Protect ON → OFF” when
a protected disc is inserted.
To cancel the disc protect:
6
Press [SET UP] to exit the setting
menu.
7
Press [VCR].
• Select “Disc Protect ON → OFF” at step 3, then
select “Yes.”
• If you insert a disc protected with this unit, “Disc
Protect ON → OFF” will appear instead of “OFF →
ON.”
Make sure to select a recording speed using
[REC SPEED]. (See page 64.)
Rewind or fast forward the tape to the point where
you want to start recording.
8
9
Press [DVD].
Press [DVD PLAY P] on the unit, and
then press [PAUSE p] at the point
you wish to start recording.
10 Press [DUBBING].
DVD to VCR duplication will start.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
35
If “No” is selected and [ENTER] or [RETURN] is
pressed, finalising is continued.
Finalising Discs
Video
Insert a recordable disc before
finalising.
1
5
Finalising is complete.
Hint
• Finalising a disc in Video mode automatically
creates a title menu.
• You can use the unit to record or edit a disc
recorded in VR mode even after it is finalised. After
you finalise a disc recorded in Video mode, you
cannot edit or record anything else on that disc.
• To reverse the finalisation of the disc, select “Undo
Finalise” at step 3.
Note
In stop mode, press [SET UP].
Recording
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
2
Select “Disc” using [Cursor U / D],
then press [ENTER].
3
Select “Finalise” using
[Cursor U / D], then press [ENTER].
4
You cannot cancel finalising a DVD-R disc once it
has started.
VR
DVD-RW
DVD-RW
DVD-R
You will need to finalise discs to play them back in
other players.
Finalising may take from several minutes up to an
hour. (A disc recorded in Video mode can take up to
15 minutes. A disc recorded in VR mode can take up
to 60 minutes.)
A shorter recording period on the disc will require a
longer time period for finalisation. Do not unplug the
mains cable during finalisation.
Select “Yes” using [Cursor U / D],
then press [ENTER].
Finalising will start.
Finalize
Finalise
• If you insert a DVD-RW disc finalised with this unit,
“Undo Finalise” will appear instead of “Finalise.”
• DO NOT power off during finalising. This may result
in a malfunction.
Auto Finalise
Video
DVD-RW
DVD-R
You can finalise discs automatically when the disc
space runs out if you set this in the Setting menu.
1
2
Yes
No
In stop mode, press [SET UP].
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
If it has already appeared, proceed to step 3.
3
Select “Recording” using
[Cursor U / D], then press [ENTER].
4
Select “Auto Finalise” using
[Cursor U / D], then press [ENTER].
DVD
Recording
To cancel finalising (DVD-RW only):
At step 4, press [STOP S], select “Yes,” then
press [ENTER]. Finalising is cancelled and the
unit switches to stop mode.
DVD-RW Recording Format
Video mode
Auto Chapter
10 minutes
Timer Programming
Auto Finalise
Bilingual Recording Audio
Main
External input Audio
Stereo
Dubbing Mode
VCR
DVD
Do you want to cancel ?
Yes No
5
6
Finalising
10%
If
appears when [STOP S] is pressed, you
cannot cancel finalising because the finalising has
already reached at a critical point in its process.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
36
7
Press [ENTER].
Select “ON” using [Cursor U / D],
then press [ENTER].
Press [SET UP] to exit.
Note
• Auto finalise function is not available for discs
formatted in VR mode.
Playing Back Discs
Disc
Information on Playing Back
DVDs
Read the following information before you play back a
DVD.
Playable Discs
You can play back all the discs listed on the right.
Before attempting to play back a DVD, make sure it
meets the requirements for Region Codes and Colour
Systems as described in this section. Discs that bear
any of the logos shown below will be played back
correctly in this unit. Other disc types are not
guaranteed to be played back.
Logo
DVD-Video
DVD-RW
(VIDEO/VR mode)
DVD-R
(VIDEO mode)
DVD+RW*
Colour Systems
Region Codes
This unit has been designed to play back DVDs within
Region Two (2.) This unit can play back DVD discs
labelled with the following region codes only:
2
ALL
You cannot play back DVDs that are labelled for other
regions. If these region symbols do not appear on
your DVD, you cannot play back the DVD in this unit.
The number inside the globe refers to region of the
world.
A DVD labelled for a specific region can only be
played back in the unit with the same region code.
DVD+R*
Playing Back Discs
DVDs are recorded using different colour systems
throughout the world. The most common colour
system, used primarily in the U.K. and other EU
countries, is PAL.
This unit uses the PAL system. However, it is also
possible to play back DVDs using other colour
systems, such as NTSC.
CD-DA
(AUDIO CD)
VCD
(VIDEO CD)
DIGITAL VIDEO
CD-RW
(CD-DA FORMAT,
MP3, JPEG files)
CD-R
(CD-DA FORMAT,
MP3, JPEG files)
* There may be a disc which cannot be used or
played back.
is a trademark of DVD Format / Logo
Licensing Corporation.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
37
8
To eject the disc, press
[OPEN/CLOSE/EJECT O] to open the disc tray,
then remove the disc. Press
[OPEN/CLOSE/EJECT O] to close the disc tray
before turning off the unit.
Basic Playback
Hint for DVD Playback
The contents of a DVD are generally divided into
titles. Titles are sometimes further subdivided into
chapters.
Start Rec.
Press [STOP S] to stop playback.
Stop/Start
Stop Rec.
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3
Chapter 1 Chapter 2
Hint
• For DVD-R (Video mode) and DVD-RW (Video
mode) discs that are already finalised, a title list will
be displayed instead of thumbnails.
• If you insert a DVD-RW recorded in VR mode and it
has a Playlist, the Playlist is displayed.
• You can resume playback from where you stopped
playing back the disc (Resume playback).
See page 41 for details.
Note
Playing Back a DVD-RW / DVD-R /
DVD+RW / DVD+R Disc
Video
VR
DVD-RW
DVD-RW
DVD-R
DVD+R
DVD+RW
VD+RW
W
• Some discs may start playback automatically.
Playing Back a DVD-Video / CD /
Video CD
DVD-V
Playing Back Discs
Press [STANDBY/ON
the unit.
/I] to turn on
Follow steps 1 to 5 in “Playing Back
a DVD-RW / DVD-R / DVD+RW /
DVD+R Disc.”
2
Press [PLAY P] to start playback.
Playback will start.
To play back a DVD, turn on the TV and be sure
to select the input to which the unit is connected.
If you are playing back a DVD-Video or a Video
CD, a menu may appear.
See pages 39 - 40 for details.
2
3
Press [DVD].
Press [OPEN/CLOSE/EJECT O] to
open the disc tray.
3
4
Place the disc on the disc tray with
its label facing up. Be sure to align
the disc with the disc tray guide.
Playing Back an MP3 /JPEG
Press [STOP S] to stop playback.
MP3
1
Disc tray
guide
5
Press [OPEN/CLOSE/EJECT O] to
close the disc tray.
6
Press [TOP MENU] to display the title
menu.
You can switch between the “Original” and
“Playlist” in the VR mode using [MENU/LIST].
7
Select the desired title using
[Cursor U / D / L / P], then press
[ENTER].
Playback will start.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
38
VCD
1
DVD+R
DVD+R
1
CD
JPEG
Follow steps 1 to 5 in “Playing Back
a DVD-RW / DVD-R / DVD+RW /
DVD+R Disc.”
The file list will appear.
• If you are in the stop mode, press [TOP MENU]
to display the file list.
File List
disc name
folder name 1
folder name 2
folder name 3
folder name 4
1 file name 1
2 file name 2
3 file name 1
4 file name 2
1/2
To exit the menu, press [TOP MENU].
2
Press [Cursor U / D] to select the
desired folder (group) or file (track),
then press [ENTER].
If a file is selected:
Playback will start.
If a folder is selected:
The files in the folder will appear.
Press [Cursor U / D] to select the track or folder
you want, then press [ENTER].
• Press [PLAY P], [ENTER] or [Cursor P] to
move to any lower folders.
• Press [Cursor L] or [RETURN] to move back to
the folder above.
• Press [STOP S] to return to the first item.
Playing Back Discs Using the Disc
Menu
DVD-V
A DVD contains a disc menu, which lists the contents
and enables you to customize playback. The menu
may offer choices for subtitle languages, special
features, and chapter selection. Usually this
information appears automatically when you start
playback, but sometimes you need to press
[MENU/LIST] to display the menu.
Press [DVD] first.
1 Press [MENU/LIST].
If the feature is not available,
the TV screen.
2
[JPEG] Size of picture
• Upper limit: 6300 x 5100 dots
• Lower limit: 32 x 32 dots
• Capacity limit: less than 2.2 MB
Select an item using
[Cursor U / D / L / P], then press
[ENTER].
Repeat this step until all the features you want are
set up or to start playing back the disc from the
menu. The following operations are available.
[MENU/LIST] button:
Displays the DVD menu, which will vary among
discs, and may be same with the Title menu.
[Cursor U / D / L / P] buttons:
Move the cursor from item to item on the screen.
[ENTER] button:
Selects the currently highlighted menu option.
It is recommended that files to be played back in
this unit are recorded under the following
specifications:
[MP3]
• Sampling frequency: 44.1 kHz or 48 kHz.
• Constant Bit Rate: 112 kbps to 320 kbps.
may appear on
Playing Back Discs
Hints for MP3 / JPEG files:
• Folders are known as Groups, files are known
as Tracks.
• Folders are shown with the
icon.
• MP3 files are shown with the
icon.
Playback will start from the selected track and
continue with each one after.
• JPEG files are shown with the
icon.
• The unit can recognize up to 255 groups (or
folders) and up to 255 tracks.
• The name of each folder and file can be
displayed using up to 29 characters.
Unrecognisable characters are replaced with
asterisks.
• Unplayable groups and tracks may be displayed
depending on the recording conditions.
• For MP3 file recorded in Variable Bit Rate
(VBR), the unit may not display the actual
elapsed time.
• If there are no files in the folder, “No Files” is
displayed.
• High resolution or large-size JPEG files take a
few moments to be displayed.
• It is not possible to play back progressive
JPEGs (JPEG files saved in progressive format)
on this unit.
• It is not possible to play back JPEG files of 2.2
MB or more.
Note
• MP3 files cannot be recorded as digital sound using
an MD or DAT deck.
• Files with extensions other than “.mp3 (MP3)” or
“.jpg / .jpeg (JPEG)” will not be listed in the File List.
• Some folders or tracks listed in the File List may be
unplayable due to their recording status.
• The File List displays only up to 8 folder and file
names.
[the Number buttons]:
Selects a numbered menu option (available on
certain discs.)
3
Press [MENU/LIST] to exit the disc
menu.
Note
• Menus vary among discs. Refer to the information
accompanying the disc for details.
Hint
• During JPEG playback, press [Cursor P] or
[Cursor L] to rotate a picture 90 degrees clockwise
or counterclockwise respectively. (Not available
when the display menu appears.)
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
39
Playing Back a Disc Using the Title
Menu
DVD-V
Some DVDs have a title menu, which lists the titles
available on the DVD. You can start playing back such
discs at a specific title.
Press [DVD] first.
1
Press [TOP MENU].
The title menu will appear.
If the feature is not available,
the TV screen.
2
may appear on
Select a desired item using
[Cursor U / D / L / P], then press
[ENTER].
The disc will start playing back at the title you
selected. The following operations are available.
[TOP MENU] button:
Displays the DVD title menu which will vary
between discs.
[Cursor U / D / L / P] buttons:
Move the cursor from item to item on the screen.
Playing Back Discs
[ENTER] button:
Selects the currently highlighted menu option.
PBC Function for Video CDs
VCD
This unit conforms to ver.1.1 and ver.2.0 of the Video
CD standard playback control (PBC) function. This
enables you to play back interactive software using
menu screens. Refer to the information
accompanying the Video CD.
Ver.1.1 (without PBC function): You can still enjoy
playback of pictures and music from the CD.
Ver.2.0 (with PBC function): “PBC ON” will appear on
the screen and “Pbc” will appear on the front panel
display when playing back a Video CD with the PBC
function.
Hint
• When playing back Video CDs with the PBC
function, “Pbc” is displayed instead of the playing
back time and current track indications on the front
panel display.
Note
• Some operations cannot be performed unless the
function is cancelled either automatically or
intentionally by you.
• Operations that are not available when the PBC
function is set to “ON” are indicated by the following
symbol in this manual:
VCD
[the Number buttons]:
Selects a numbered menu option (available on
certain discs.)
3
Press [TOP MENU] to exit.
Note
• [TOP MENU] will not be available for some DVDs.
• Menus vary among discs. Refer to the information
accompanying the disc for details.
(PBC OFF)
Playing Back a Video CD Using the
Title Menu
VCD
1
When playing back a Video CD with
the PBC function, the title menu will
appear automatically.
2
Press [the Number buttons] to select
the desired title.
Playback will start at the selected title.
3
Press [RETURN] to go back to the
title menu.
Note
• While the On-Screen display appears, you cannot
perform steps 2 and 3.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
40
Cancelling and Recalling the PBC
Function
Special Playback
Resume Playback
VCD
Insert a Video CD.
1
DVD-V
In stop mode, press [SET UP].
DVD+R
DVD+RW
VD+RW
W
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
JPEG
2
Select “CD Playback Mode” using
[Cursor U / D], then press [ENTER].
3
Select “PBC (Video CD only)” using
[Cursor U / D], then press [ENTER].
1
ON
CD
VCD
MP3
During playback, press [STOP S].
The resume message will appear.
2
Press [PLAY P].
In a few seconds, playback will resume from the
point at which you stopped it before. Even if you
turn off the unit, you can resume playback at the
same point after turning back on the unit.
Program Play
5 sec.
DVD+R
DVD+R
DVD-R
You can resume playback from the point where you
stopped it before.
Random Play
Slide Show
VR
DVD-RW
(PBC OFF)
CD Playback Mode
PBC(Video CD only)
Video
DVD-RW
To cancel the resume playback and start playing
back the disc from the beginning:
Press [STOP S] twice while playback is stopped.
4
Select “OFF” using [Cursor U / D],
then press [ENTER].
5
Press [SET UP] to exit.
To recall the PBC function, select “ON” in step 4
above.
Fast Forward / Fast Reverse
Note
DVD-V
DVD-V
• The default setting of “PBC (Video CD only)” is
“ON.”
DVD+R
DVD+RW
VD+RW
W
1
Video
VR
DVD-R
DVD-RW
VD-RW
W
DVD-RW
DVD+R
DVD+R
CD
Playing Back Discs
Note
• For Video CDs, if you turn PBC on using the setting
menu, the resume function is cancelled.
• For MP3 and JPEG files, playback will resume from
the beginning of the track at which playback was
stopped.
DVD-R
VCD
MP3
During playback, press [FWD f] or
[REV r].
Each time you press [FWD f] or [REV r], the
approximate speed will change as follows.
To output sound from DVDs during fast
forward at x1.5 speed, set “Fast Forward with
Audio” to “ON” for the “Playback” setting in
“Advanced Setting Menu.”
Fast forward or fast reverse playback across titles
(for DVDs) or tracks (for MP3) is not possible.
x40
x20
x5
Normal
speed
playback
x1.5
x20
x40
• For Audio CDs, approximate speed is fixed at x8
with sound.
• For Video CDs, approximate forward speeds are
x1.5, x8 and x16, and approximate reverse
speeds are x2, x8 and x16.
• For MP3 files, approximate speed is fixed at x16.
• To return to playback at normal speed, press
[PLAY P].
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
41
Hint
• Forward / reverse speeds are indicated with icons
as follows.
Forward (Approx. Speed):
x1.5:
x20:
x40:
Reverse (Approx. Speed):
x5:
x20:
x40:
Step by Step Playback
DVD-V
DVD+R
DVD+RW
VD+RW
W
1
2
Press and hold [F] to continue going forward.
To continue going backward, press and hold
[B].
3
].
Normal playback will start 30-second advanced
point from the point at which you press [
].
Each time you press [
], the start point will
move another 30 seconds forward and playback
resume automatically.
You can press [
] up to 6 times (180 seconds.)
Playing Back Discs
DVD-V
DVD+R
DVD+RW
VD+RW
W
Note
Slow Forward / Slow Reverse
Playback
DVD-V
VR
DVD-RW
DVD-RW
DVD+R
DVD+R
CD
DVD-R
VCD
MP3
JPEG
1
Press [PLAY P] to resume playback.
• Only step by step forward is available when playing
back Video CDs.
Pause
Video
DVD+R
DVD+RW
VD+RW
W
1
During playback, press [PAUSE p].
Press [PLAY P] to resume playback.
For JPEG files, playback will start from the
beginning of the track.
Video
VR
DVD-RW
DVD-RW
DVD+R
DVD+R
DVD-R
VCD
During playback, press [PAUSE p],
then press [SLOW ] or [SLOW ].
Each time you press [SLOW
] or [SLOW
],
the approximate speed change as follows. (The
sound will remain muted.)
Playback will pause with the sound muted.
2
VCD
Each time you press [F], playback will go
forward one frame (or step) at a time with the
sound muted.
To go backward one frame (or step), press
[B].
VR
During playback, press [
DVD+R
DVD+R
DVD-R
Press [B / F] repeatedly.
DVD-V
DVD-RW
DVD-RW
DVD-R
To enjoy recorded programmes without any
interruptions, press [
].
1
VR
DVD-RW
During playback, press [PAUSE p].
Skipping TV Commercials During
Playback
Video
Video
DVD-RW
x1/4
x1/8
x 1 /1 6
Pause
x1/16
x1/8
x1/2
To return to normal playback, press [PLAY P].
Hint
• Forward / reverse speeds are indicated with icons
as follows.
Forward (Approx. Speed):
x1 / 16:
x1 / 8:
x1 / 2:
Reverse (Approx. Speed):
x1 / 16:
x1 / 8:
x1 / 4:
Note
• Only slow forward is available when playing back
Video CDs.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
42
Zoom
DVD-V
Marker Setup
Video
VR
DVD-RW
DVD-RW
DVD+R
DVD+RW
VD+RW
W
1
DVD+R
DVD+R
VCD
DVD-R
DVD-V
JPEG
Video
VR
DVD-RW
DVD-RW
DVD+R
DVD+RW
VD+RW
W
DVD+R
DVD+R
DVD-R
VCD
CD
(PBC OFF)
During playback, press [ZOOM].
1
1
0:00:00
DVD-Video
1.2
1.5
2.0
Four options are available, x1.0, x1.2, x1.5 and
x2.0. These are displayed excluding the current
zoom rate.
You can assign a specific point on a disc to return
later.
1
During playback, press
[ON SCREEN].
2
Select the
icon using
[Cursor L / P], then press [ENTER].
Marker setup menu for DVD-Video mode
Hint
1
1
0:00:00
DVD-Video
• You can also select the zoom function by pressing
[ON SCREEN]. In this case, press [ON SCREEN]
first, select the
icon using [Cursor L / P], and
then press [ENTER].
2
Select the desired zoom factor to
zoom using [Cursor U / D], then
press [ENTER].
Marker setup menu for Audio CD mode
1
The zoom area is displayed.
Audio CD
Select the desired zoom position
using [Cursor U / D / L / P], then
press [ENTER].
Zoom playback will start.
Hint
3
• To exit the zoom menu, press [ZOOM] at step 1.
• To cancel the zoom function, select x1.0 using
[Cursor U / D], then press [ENTER].
The title (track) number and the time are
displayed.
Note
• If selecting a smaller factor than that currently
selected, the zoom area is not displayed.
• You cannot slide the zoomed picture on some JPEG
files.
Select the desired marker number
using [Cursor U / D]. When the disc
reaches the desired point, press
[ENTER].
Playing Back Discs
3
0:00:00
4
To return to the marker later, select
the desired marker number using
[Cursor U / D], then press [ENTER].
Hint
• To clear a marker, select the marker number you
wish to clear, then press [CLEAR].
• You can mark up to 6 points.
Note
• All markers are erased when you perform the
following operations.
- Open the disc tray.
- Turn off the power.
- Record on a recordable disc.
- Change the mode between Original and Playlist.
(VR mode)
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
43
Track Search
Search
CD
Title / Chapter Search
DVD-V
DVD+R
DVD+RW
VD+RW
W
Video
VR
DVD-RW
DVD-RW
DVD-R
1
DVD+R
DVD+R
To go back to the previous title or chapter, press
[B] repeatedly.
Using the [ON SCREEN] button
Playing Back Discs
1
During playback, press
[ON SCREEN].
2
Select the
icon using
[Cursor L / P], then press [ENTER].
Title search will start.
Hint
• Total number of chapters and playback time of the
selected title are also displayed.
Searching for a Chapter:
4
Press [Cursor L / P] to highlight the
number displayed in the right side of
the
icon.
Enter the desired chapter number to
search for using [Cursor U / D] or
[the Number buttons], then press
[ENTER].
Chapter search will start.
Hint
• The title number and playback time of the selected
chapter are also displayed.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
44
1
During playback, press
[ON SCREEN].
2
Select the
icon using
[Cursor L / P], then press [ENTER].
for the track number is highlighted.
3
Enter the desired track number to
search for using [Cursor U / D] or
[the Number buttons], then press
[ENTER].
Track search will start.
Searching for a Title:
Enter the desired title number to
search for using [Cursor U / D] or
[the Number buttons], then press
[ENTER].
During playback, press [F] to skip
the current track and move to the
next.
Using the [ON SCREEN] button
for the title number is highlighted.
3
JPEG
The unit moves to the next track one after the
other.
To go back to the previous track, press [B]
repeatedly. The unit moves backward one track at
a time.
During playback, press [F] to skip
the current title or chapter and move
to the next.
The unit moves to the next title or chapter one
after the other.
3
MP3
Using [B / F] buttons
Using [B / F] buttons
1
VCD
(PBC OFF)
Hint
• For Video CDs, you can perform the track search
function in stop mode without turning PBC off
manually.
Note
• During Random playback or Programme playback,
you cannot search the desired track.
Direct Search
CD
You can search the desired track directly.
Using [the Number buttons]
1
During playback, if the display menu
is not displayed, press [the Number
buttons] to enter the desired track
number.
Note
• During Random playback or Programme playback,
you cannot search the desired track directly.
Time Search
DVD-V
DVD+R
DVD+RW
VD+RW
W
Video
VR
DVD-RW
DVD-RW
DVD+R
DVD+R
Repeat / Random / Programme
Playback / Slide Show
DVD-R
VCD
CD
(PBC OFF)
1
2
Repeat Playback
During playback, press
[ON SCREEN].
DVD-V
Select the
icon using
[Cursor L / P], then press [ENTER].
DVD+R
DVD+RW
VD+RW
W
Press [Cursor L / P] to highlight
.
Enter the desired time to search for
using [Cursor U / D] or [the Number
buttons], then press [ENTER].
Note
CD
VCD
MP3
1
During playback, press
[ON SCREEN].
2
Select the
icon using
[Cursor L / P], then press [ENTER].
The Repeat mode menu will appear.
• You can directly access this menu by pressing
[REPEAT] also.
Hint
3
Select the desired option to repeat
using [Cursor U / D], then press
[ENTER].
The selected repeat playback will start.
The following operations are available.
Title:
The current title will be played back repeatedly.
(DVD only)
Chapter:
The current chapter will be played back
repeatedly.
(DVD only)
Playing Back Discs
• During Random playback or Programme playback,
you cannot search the desired time.
• The title number and chapter number of the setting
time are also displayed.
• Time search function is available only in the same
track or title.
• If the time search is not available, – –:– –:– – / – –:–
–:– – (or 0:00:00 / 0:00:00) is displayed.
DVD+R
DVD+R
DVD-R
JPEG
Time search will start.
• For Video CDs, you can perform the time search
function in stop mode without turning PBC off
manually.
VR
DVD-RW
(PBC OFF)
for the title or track number is highlighted.
3
4
Video
DVD-RW
All:
The current disc will be played back repeatedly.
(DVD-RW (VR mode), CD, Video CD, MP3 and
JPEG only)
A-B:
The A-B point will be played back repeatedly.
(DVD, CD and Video CD only)
When pressing [ENTER] while A-B is highlighted,
A-B repeat is set.
• Press [ENTER] again to decide the starting
point (A).
• Press [ENTER] after setting point (A) to select
the ending point (B).
Track:
The current track will be played back repeatedly.
(CD, Video CD, MP3 and JPEG only)
Group:
The current group will be played back repeatedly.
(MP3 and JPEG only)
Hint
• To cancel the repeat playback, select “OFF” at step
3. The repeat setting is also cancelled when you
stop playback.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
45
2
Note
• You can only set A-B repeat playback within the
current title (for DVDs) or current track (for Audio
CDs and Video CDs.)
• You cannot select “Group” during the random
playback of MP3 files.
• For Video CDs with PBC function, repeat playback
does not work while the PBC function is on.
Select “Program Play” using
[Cursor U / D], then press [ENTER].
Program Play
Random Playback
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Total
CD
VCD
MP3
JPEG
(PBC OFF)
You can use this function to play back a disc randomly
instead of in the recorded order.
1
In stop mode, press [SET UP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
2
Select “CD Playback Mode” using
[Cursor U / D], then press [ENTER].
The CD Playback Mode menu will appear.
3
Select “Random Play” using
[Cursor U / D], then press [ENTER].
Playing Back Discs
Random playback will start.
Hint
• To cancel random playback, press [STOP S] twice
during random playback. “Playmode OFF” appears
on the screen.
• For Video CDs with PBC function, the PBC setting
will switch to off automatically during random
playback.
Note
• During random playback, if you forward the track to
the end, the playback speed of the next track will be
normal.
• During random playback, you cannot use the search
function except for the search with [B / F].
By pressing [B], you can return only to the
beginning of the current track.
Programme Playback
CD
3
Select the desired track using
[Cursor U / D], then press [ENTER]
or [Cursor P].
4
Press [PLAY P] to start programme
playback.
Hint
• To erase tracks you selected, press [CLEAR].
• You can make up to 50 track settings.
• To cancel programme playback, press [STOP S]
twice during programme playback. “Playmode OFF”
appears on the screen.
• You may also select the desired track using
[the Number buttons] at step 3.
• For Video CDs with PBC function, the PBC setting
will switch to off automatically during programme
playback.
Note
• During programme playback, if you forward the track
to the end, the playback speed of the next track will
be normal.
• During programme playback, you cannot use the
search function except for the search with
[B / F].
Slide Show
JPEG
You can select the display time between 5 seconds
and 10 seconds.
1
Follow steps 1 and 2 in “Random
Playback.”
2
Select “Slide Show” using
[Cursor U / D], then press [ENTER].
3
Select the display time using
[Cursor U / D], then press [ENTER].
VCD
(PBC OFF)
You can programme the disc to play back in your
desired order.
1
0:00:00
Follow steps 1 and 2 in “Random
Playback.”
Note
• Large-size JPEG files take a few moments to be
displayed.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
46
Selecting the Format of Audio
and Video
You can select the format of audio and video to suit
the content of the disc you are playing back.
Switching Audio Soundtrack
VR
DVD-V
DVD-RW
CD
VCD
VR
DVD-V
D
VD-V
DVD-R
DVD-RW
VD-RW
W
Many DVD-Videos have subtitles in one or more
languages. The languages available are usually
printed on the disc case. You can switch subtitle
languages at any time during playback.
1
During playback, press
[ON SCREEN].
2
Select the
icon using
[Cursor L / P], then press [ENTER].
3
Select the desired subtitle language
using [Cursor U / D], then press
[ENTER].
MP3
When playing back a DVD-Videos recorded with two
or more soundtracks (often in different languages),
you can switch among them during playback.
When playing back DVD-RW discs recorded in VR
mode, you can switch to main audio (L), sub audio (R)
or a combination of both (L / R.)
When playing back Audio CDs, Video CDs or MP3
files, you can switch among the left, the right channel,
and stereo.
1
Switching Subtitles
Subtitles are displayed in the selected language.
If you select “OFF,” subtitles will disappear.
Note
During playback, press
[ON SCREEN].
Press [AUDIO] during playback, and follow from
step 3.
Select the
icon using
[Cursor L / P], then press [ENTER].
3
Select a desired audio soundtrack or
audio channel using [Cursor U / D],
then press [ENTER].
Playing Back Discs
2
• With some discs it is only possible to change the
subtitle language from the disc menu. Press
[TOP MENU] or [MENU/LIST] to display the disc
menu.
• If a 4-digit language code appears in the subtitle
menu at step 2, refer to the “Language Code” on
page 71.
With a DVD-Video:
Audio soundtrack will switch.
Example:
English → Spanish → French
With a DVD-RW in VR mode:
Audio channel menu will appear.
Follow the step 4.
With an Audio CD, Video CD, or MP3 files:
The Audio channel will switch.
Example:
STEREO → L-ch → R-ch
4
Select the desired audio channel
using [Cursor U / D], then press
[ENTER].
The Audio channel will switch.
Note
With some discs it is only possible to change the
soundtrack from the disc menu. Press [TOP MENU]
or [MENU/LIST] to display the disc menu.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
47
Switching Camera Angles
Reducing Block Noise
DVD-V
Some DVD-Videos feature scenes shot from two or
more angles. The disc case is usually marked with an
angle icon if the disc has multi-angle scenes.
1
During playback, press
[ON SCREEN].
The angle icon appears when a switching camera
angle is available. (Available only when the angle
icon appears in bottom right on the TV screen.)
2
Select the
icon using
[Cursor L / P], then press [ENTER].
The angle will switch each time you press
[ENTER].
Hint
• Even when the
icon is not displayed, you can
select the angle if the currently played back title has
at least two multi-angle scenes.
Playing Back Discs
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
48
DVD-V
DVD+R
DVD+RW
VD+RW
W
Video
VR
DVD-RW
DVD-RW
DVD+R
DVD+R
DVD-R
VCD
1
During playback, press
[ON SCREEN].
2
Select the
icon using
[Cursor L / P], then press [ENTER].
The Noise Reduction menu will appear.
3
Select the desired option using
[Cursor U / D], then press [ENTER].
This function reduces noise in the playback picture.
When playing back discs recorded in long time modes
such as SLP or SEP, select “Type 1” or “Type 2.”
“Type 2” is more effective.
When playing back discs with a little noise, such as
DVD-Videos, select “OFF.”
Editing
Disc Editing
Editing Discs in Video Mode
You can edit a disc recorded using the PAL system. It
is not possible to edit discs recorded using the NTSC
system.
You can edit the following disc items in Video mode.
• Deleting Titles (See below.)
• Editing Titles (See page 50.)
• Setting or Clearing Chapter Markers (See page 51.)
Guide to a Title List
Note
The title list enables you to check the titles recorded
on a disc easily. You can choose a title to play back
from the screen and easily edit the titles as you wish.
The items on the title list are as follows.
Original
1
2
3
5
6
Insert a recordable disc.
Deleting Titles
15/04 19:00 P12 XP
4
• After a disc is finalised, editing the disc or recording
on the disc is not possible (except DVD-RW discs in
VR mode.)
• A Playlist is not available for DVD-R or DVD-RW
discs in Video mode.
• It is not possible to edit a disc recorded in another
video system other than PAL, such as NTSC.
Video
1
3
2
Original
1
Title Delete
Protect
DVD-RW
DVD-R
You can delete titles you do not want to keep.
In Video mode, recordable disc space of DVD-RW
disc will increase when the last title on the title list is
deleted. However, deleting the title will not change
recordable disc space for DVD-R disc.
In finalised DVD-R or DVD-RW (in Video mode) discs,
you cannot select the title list because it cannot be
edited once finalised.
Editing
Note
• It is not possible to retrieve deleted titles.
Press [DVD] first.
15/04 19:00 P12 XP
1
0:00:59
8 7
1
2
3
4
5
6
7
8
6
5
4
To select a title recorded on the disc for editing,
move the cursor to the title and press [ENTER].
If the title is protected, the Protect icon will
appear.
• It is not possible to protect a title on the Playlist.
Arrow icons mean the title list includes a next or
previous page. Press [Cursor L / P] in the
direction of the icon you wish to follow.
Available title editing menu items vary depending
on the disc and format types.
You can edit the title and details as you wish.
Time status bar of the recording.
• After editing, playback starts from this point.
The selected title from the title list thumbnails.
• The selected title is played back automatically.
Playback status of the current disc.
Downloaded From DvDPlayer-Manual.com JVC Manuals
In stop mode, press [SET UP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
2
Select “Disc” using [Cursor U / D],
then press [ENTER].
3
Select “Title List” using
[Cursor U / D], then press [ENTER].
Disc
Title List
Format
Finalise
EN
49
4
Select the desired title using
[Cursor U / D / L / P], then press
[ENTER].
3
2
Select “Edit Title Name” using
[Cursor U / D], then press [ENTER].
A window for entering the title name will appear.
3
Title List
1
2
To enter the title name, refer to
“Guide to Editing Title Names” on
this page.
Title List - Edit Title Name
15/04 19:00 P12 XP
4
5
6
5
6
Select “Title Delete” using
[Cursor U / D], then press [ENTER].
6
C
c
3
?
15/04 19:00 P12 XP
0:00:59
Title List
Title Delete
Edit Title Name
Chapter Mark
A B
a b
1 2
@ !
When you finish entering the title name, press
[ENTER].
4
Select “Yes” using [Cursor U / D],
then press [ENTER].
The name you edited becomes the title.
5
15/04 19:00 P12 XP
0:00:59
You cannot select “Chapter Mark” when a DVD-R
disc is inserted into the unit. For DVD-RW discs in
Video mode, you cannot select the chapter mark
of the title which is less than 5 minutes.
6
Select “Yes” using [Cursor U / D],
then press [ENTER].
The title is deleted.
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Guide to Editing Title Names
Step 1: Select the desired character set using
[Cursor U / D], then press [ENTER].
Editing
Step 2: Using the list below as a guide, press
[the Number buttons] repeatedly until the
desired letter appears.
Select
Title List - Title Delete
Press
6
Yes
No
ABC
abc
123
@!?
<space>
<space>
0
<space>
–
–
1
ABC
abc
2
–
DEF
def
3
–
GHI
ghi
4
–
JKL
jkl
5
–
MNO
mno
6
–
PQRS
pqrs
7
–
TUV
tuv
8
–
WXYZ
wxyz
9
–
! ”# $ % & ’( )
*+,-./:;<=>
[email protected][]^_{|}
15/04 19:00 P12 XP
0:00:59
7
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Editing Titles
Video
DVD-RW
DVD-R
You can edit the title names from this menu.
The title names you edit will appear on the title list.
Press [DVD] first.
1
Follow steps 1 to 4 in “Deleting
Titles.”
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
50
• Characters set will be changed to the “@!?”
automatically if you press [1] after you selected the
“ABC” or “abc” mode.
7
Note
• To delete letters, press [CLEAR] repeatedly. Press
and hold [CLEAR] to delete all letters.
• To move on to the next set of letters, press
[Cursor P].
• You can enter up to 30 letters.
• Unrecognisable characters will be replaced with
asterisks (*). If you delete them, adjoining
characters may change to asterisks (*) or other.
Select “Yes” using [Cursor U / D],
then press [ENTER].
Title List - Chapter Mark - 5 minutes
6
15/04 19:00 P12 SP
Setting or Clearing Chapter Markers
1:00:59
Chapter markers are added.
If you select “OFF” at step 6, all the chapter
markers are erased.
Video
DVD-RW
You can add chapter markers to a title. After a title is
marked with chapters, you can use the chapter
search feature.
You can specify the interval of chapter markers for
titles last more than 5 minutes.
8
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Note
Press [DVD] first.
1
Yes
No
In stop mode, press [SET UP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
Select “Disc” using [Cursor U / D],
then press [ENTER].
3
Select “Title List” using
[Cursor U / D], then press [ENTER].
4
Select the desired title using
[Cursor U / D / L / P], then press
[ENTER].
5
Select “Chapter Mark” using
[Cursor U / D], then press [ENTER].
6
Select the desired interval using
[Cursor U / D], then press [ENTER].
Editing
2
• You cannot select a chapter marker interval that
exceeds the length of a title.
• The length of chapters may deviate slightly from the
one specified at the step 6.
• A chapter marker may be delayed depending on the
recording content.
Title List - Chapter Mark
6
OFF
5 minutes
10 minutes
15 minutes
30 minutes
60 minutes
15/04 19:00 P12 SP
1:00:59
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
51
Editing Discs in VR Mode
Original Editing Original Titles
in VR Mode
For discs in VR mode, you can edit from the “Original”
menu or the “Playlist” menu that you create from the
original.
Insert a recordable disc before editing.
Editing original titles Original
Original Deleting Titles
You can perform the following operations on the
original titles.
• Deleting Titles (See this page.)
• Protecting Titles (See page 53.)
• Releasing Titles from Protecting (See page 53.)
DVD-RW
When a title is deleted from an original list in VR
mode, the available recording time on the disc will
increase.
Editing playlists Playlist
You can create a Playlist from original titles, and edit it
to your preference without losing the original titles.
You can perform the following operations on the
Playlist.
• Deleting Titles (See page 54.)
• Deleting Parts of Titles (Scene Delete) (See page
54.)
• Editing Titles (See page 55.)
• Setting or Clearing Chapter Markers (See page 55.)
• Setting Pictures as Thumbnails (See page 56.)
• Dividing a Title (See page 56.)
• Combining Titles (See page 57.)
• Adding Titles to a Playlist (See page 57.)
• Deleting a Playlist (See page 57.)
VR
Note
• It is not possible to retrieve deleted titles.
Press [DVD] first.
1
In stop mode, press [SET UP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
2
Select “Disc” using [Cursor U / D],
then press [ENTER].
3
Select “Original” using
[Cursor U / D], then press [ENTER].
Disc
Note
Playlist
• After editing, titles will not remain as recorded
originally. If you want to keep the original as it is, edit
the Playlist to your preference.
Original
Format
Finalise
Disc Protect OFF
ON
Editing
4
Select the desired title using
[Cursor U / D / L / P], then press
[ENTER].
5
Select “Title Delete” using
[Cursor U / D], then press [ENTER].
Original
3
Title Delete
Protect
15/04 19:00 P12 XP
0:00:59
6
Select “Yes” using [Cursor U / D],
then press [ENTER].
The title is deleted.
7
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Note
• When you delete the original title, the corresponding
part of the playlist will also be deleted.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
52
Original Protecting Titles
VR
DVD-RW
To prevent the accidental editing or erasing of the
titles, you can protect them in the original menu.
Press [DVD] first.
1
Original Releasing Titles from
Protecting
VR
DVD-RW
You can cancel the title protection feature after it is
applied.
In stop mode, press [SET UP].
Press [DVD] first.
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
1
2
Select “Disc” using [Cursor U / D],
then press [ENTER].
Follow steps 1 to 4 in
“ Original Protecting Titles.”
2
Press [ENTER].
3
Select “Original” using
[Cursor U / D], then press [ENTER].
4
Select the desired title using
[Cursor U / D / L / P], then press
[ENTER].
5
Select “Protect” using
[Cursor U / D], then press [ENTER].
Original - Protect
3
3
OFF
15/04 19:00 P12 XP
0:00:59
3
Original
ON
Press [ENTER] again.
The key icon will disappear from the title in the
original list.
Title Delete
Protect
4
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
15/04 19:00 P12 XP
0:00:59
Press [ENTER] again.
Editing
6
Original - Protect
3
OFF
ON
15/04 19:00 P12 XP
0:00:59
7
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
To protect a whole disc (DVD-RW VR mode
only):
Select “Disc Protect” from the Disc menu, then
select “Yes.” Refer to “Setting a Disc to Protect”
on page 35.
Hint
• The protected title is marked with a key icon in the
original list.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
53
Playlist Editing the Playlist in
VR Mode
Note
• When you play back the disc of which the playlist is
edited, select “Playlist” in the title menu.
Insert a recordable disc before editing.
Playlist Deleting Parts of Titles
(Scene Delete)
VR
DVD-RW
You can delete a specific part of a title.
Even when a title is deleted from the playlist, the
original title will remain.
The available recording time on the disc will not
increase.
Press [DVD] first.
Playlist Deleting Titles
1
Follow steps 1 to 4 in
“ Playlist Deleting Titles.”
2
Select “Scene Delete” using
[Cursor U / D], then press [ENTER].
3
Use [B / F], [REV r], [FWD f],
[PLAY P] and [PAUSE p] to find the
start point, then press [ENTER].
VR
DVD-RW
In VR mode, even when a title is deleted from the
Playlist, the original title will remain in the Original list.
The recordable disc space to record will not increase.
Press [DVD] first.
1
In stop mode, press [SET UP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
2
Playlist - Scene Delete
Select “Disc” using [Cursor U / D],
then press [ENTER].
Select “Playlist” using
[Cursor U / D], then press [ENTER].
4
Select the desired title using
[Cursor U / D / L / P], then press
[ENTER].
5
Select “Title Delete” using
[Cursor U / D], then press [ENTER].
Editing
3
3
Use [B / F], [REV r], [FWD f],
[PLAY P] and [PAUSE p] again to
move to the end point, and press
[ENTER].
Playlist - Scene Delete
3
Playlist
3
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture
Title Dividing
Title Combining
6
Select “Yes” using [Cursor U / D],
then press [ENTER].
The title is deleted.
7
End
Preview
Delete
4
Select “Delete” using
[Cursor U / D], then press [ENTER].
5
Select “Yes” using [Cursor U / D],
then press [ENTER].
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Start
The cursor will move to “Preview.” You can check
the preview by pressing [ENTER].
The bar at the bottom of the screen indicates the
total and the elapsed time of the title, and the area
selected for deletion is indicated in red during the
preview.
15/04 19:00 P12 XP
0:00:59
Start
End
Preview
Delete
The part of the title is deleted.
6
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Note
• You cannot select “Scene Delete” if the number of
chapter markers in the Original or Playlist is more
than 900.
• The recordable disc space will not increase after
deleting parts of titles.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
54
Playlist Editing Titles
3
Use [B / F], [REV r], [FWD f],
[PLAY P] and [PAUSE p] to find the
point where you will create a new
chapter marker.
Or, use [B / F] to find a chapter
marker that you wish to delete.
4
Select “Add” or “Delete” accordingly
using [Cursor U / D], then press
[ENTER].
VR
DVD-RW
You can edit the title names from this menu.
The names you edit will appear on the title list.
Press [DVD] first.
1
Follow steps 1 to 4 in
“ Playlist Deleting Titles.”
2
Select “Edit Title Name” using
[Cursor U / D], then press [ENTER].
3
To enter the title name, refer to
“Guide to Editing Title Names” on
page 50.
Playlist - Chapter Mark
3
Chapter
Add
Delete
2/ 2
15/04 19:00 P12 XP
Playlist - Edit Title Name
0:00:59
6
A
a
1
@
B
b
2
!
C
c
3
?
You cannot delete the first chapter of a title.
5
15/04 19:00 P12 XP
Playlist - Chapter Mark - Add
0:00:59
3
When you finish entering the title name, press
[ENTER].
4
Chapter
Select “Yes” using [Cursor U / D],
then press [ENTER].
The name you edited becomes the title.
2/ 2
15/04 19:00 P12 XP
0:00:59
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Playlist Setting or Clearing Chapter
Markers
VR
DVD-RW
You can add chapter markers to a title. After a title is
marked with chapters, you can use the chapter
search feature.
You can set a chapter marker anywhere you want.
You cannot set more than 999 chapter markers in the
Playlist.
Yes
No
A chapter marker is added.
Adding a chapter marker:
If you select “Add” at step 4, a new chapter marker is
created at the point you specified.
Editing
5
Select “Yes” using [Cursor U / D],
then press [ENTER].
Deleting a chapter marker:
If you select “Delete” at step 4, the chapter marker
you selected is deleted.
6
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Press [DVD] first.
1
Follow steps 1 to 4 in
“ Playlist Deleting Titles.”
2
Select “Chapter Mark” using
[Cursor U / D], then press [ENTER].
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
55
Playlist Setting Pictures as
Thumbnails
VR
DVD-RW
You can set a picture as a thumbnail for each title.
This helps you to remember the content of the title
without having to play it back. The first picture of the
title is selected as the default.
Press [DVD] first.
1
Follow steps 1 to 4 in
“ Playlist Deleting Titles.”
2
Use [B / F], [REV r], [FWD f],
[PLAY P] and [PAUSE p] to find the
picture you want to set as a
thumbnail, then press [ENTER].
3
Select “Index Picture” using
[Cursor U / D], then press [ENTER].
4
Playlist Dividing a Title
VR
DVD-RW
You can divide a title into two new titles.
Press [DVD] first.
1
Follow steps 1 to 4 in
“ Playlist Deleting Titles.”
2
Use [B / F], [REV r], [FWD f],
[PLAY P] and [PAUSE p] to find the
point where you wish to divide the
title.
3
Select “Title Dividing” using
[Cursor U / D], then press [ENTER].
4
Select “Yes” using [Cursor U / D],
then press [ENTER].
The title is divided into two new titles with the
same title names.
The thumbnail you set is reset to the first picture
of each title.
Select “Yes” using [Cursor U / D],
then press [ENTER].
The picture is set as the thumbnail.
Playlist
Playlist
Title Dividing
Index Picture
3
3
Yes
Yes
No
Yes
Yes
No
P8 EP19:00 P12 XP
15/04
0:00:59
P8 EP19:00 P12 XP
15/04
0:00:59
Editing
5
5
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Note
• If a picture selected as a thumbnail is deleted by
deleting a part of a title, the default picture is
selected.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
56
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Note
• If a disc contains the maximum number of
recordings (99), you cannot divide any titles.
• You cannot divide the titles if the total number of the
chapters have already reached 999.
Playlist Combining Titles
3
Select the desired title using
[Cursor U / D / L / P], then press
[ENTER].
4
Press [SET UP].
VR
DVD-RW
You can combine two titles into a single title.
Writing on the disc starts.
It may take a while to write the data on a disc.
Press [DVD] first.
1
Follow steps 1 to 4 in
“ Playlist Deleting Titles.”
Hint
2
Select “Title Combining” using
[Cursor U / D], then press [ENTER].
3
Select another title to combine using
[Cursor U / D / L / P], then press
[ENTER].
4
Select “Yes” using [Cursor L / P],
then press [ENTER].
The two titles will combine into a single title.
Playlist
1+2
Playlist
Title Combining
1
3
2
Yes
Yes
1
No
Add New
Title
Delete
Playlist
2
04/15 19:00 P12 XP
Wait for a moment.
5
• To delete a title from the Playlist, refer to “Deleting
Titles” on page 54.
• To delete the Playlist, refer to “Deleting a Playlist” on
this page.
Playlist Deleting a Playlist
VR
DVD-RW
A Playlist can be deleted if it is no longer needed.
Press [DVD] first.
1
Follow steps 1 to 3 in
“ Playlist Deleting Titles.”
2
Select “Delete Playlist” using
[Cursor U / D / L / P], then press
[ENTER].
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Playlist
Note
1
• You cannot select the same title twice and combine
it into a single title.
• If either one of the two original titles is deleted, the
combined new title is also deleted.
Press [DVD] first.
1
2
Follow steps 1 to 3 in
“ Playlist Deleting Titles.”
3
Editing
VR
3
Add New
Title
Delete
Playlist
Playlist Adding Titles to a Playlist
DVD-RW
You can add a title to the Playlist as you wish.
You can add up to 99 titles to a Playlist (as long as the
total number of the Playlist does not exceed 999
chapters.)
2
Select “Yes” using [Cursor L / P],
then press [ENTER].
The Playlist is deleted.
4
Press [SET UP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Note
Select “Add New Title” using
[Cursor U / D / L / P], then press
[ENTER].
• Deleting a Playlist will not increase the available
recording time on the disc.
• When the disc contains 99 titles or more, or 999
chapters or more, “Add New Title” cannot be
selected.
Playlist
1
2
3
Add New
Title
Delete
Playlist
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
57
Changing the Setting Menu
Tour of the Setting Menu
The following table shows the items you can set and their default settings.
Use the table as a reference for efficient operation.
Setting menu
Language Setting
page 59
Display Setting
page 60
Audio Setting
pages 60-61
Parental Setting
pages 62-63
Menu items
Disc Menu Language
Default
English
Original
Sets the audio language.
Subtitle Language
OFF
Sets the subtitle language.
OSD Language
English
Sets the On-Screen display
(OSD) language.
FL Dimmer
Auto
Sets the front display
brightness.
Screen Saver
10 minutes
Sets the idling time before the screen
saver starts.
PCM
48kHz
Sets whether sound recorded
at 96 kHz is down sampled to
48 kHz or not.
Dolby Digital
Stream
Sets the digital audio output
signal specification.
MPEG
PCM
Sets the digital audio output
signal specification.
DTS
ON
Sets whether DTS signal is
output or not.
Dynamic Range Control
ON
Compresses the sound volume
range.
Fast Forward with Audio
ON
Outputs sound during fast
forward playback.
Parental Lock
All
Sets the DVD parental control level.
Digital Out
Changing the Setting Menu
Video Out
Sets and changes the password.
TV System
PAL
Sets the TV system.
Note
• Changes you make to the Setting menu remain even after power to the unit is switched off or the disc tray is
opened or closed.
• [SET UP] will not function when the unit is turned on by pressing [STANDBY/ON /I] during either the DVD or
the VCR timer-standby mode.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
58
Sets the disc menu language.
Audio Language
• Change password
Output Setting
page 63
Function
If “Other” is selected, enter the
appropriate 4-digit code using
[the Number buttons].
Language Setting
1 In stop mode, press [SET UP].
2 Select “Advanced Setting Menu”
Refer to the “Language Code” on page 71.
DVD
Disc Menu
Subtitle
Language
Language
using [Cursor U / D], then press
[ENTER].
Code Input
4
7
4
If it has already appeared, proceed to step 3.
3
Select “Playback” using
[Cursor U / D], then press [ENTER].
4
Select the desired item using
[Cursor U / D], then press [ENTER].
Disc Menu Language (Default: English)
DVD
Playback
Disc Menu Language
4:3 Letter Box
English
Parental Lock
ALL
All
French
Disc Menu Language
English
Spanish
Spanish
Audio Language
Original
German
Subtitle Language
OFF
Italian
Digital Out
DVD
ON
Dutch
Fast Forward with Audio
ON
OFF
Other
Press [SET UP] to exit.
• You can also change or switch off the subtitles on a
DVD from the disc menu if it is available.
• Press [CLEAR] or [Cursor L] to erase numbers
entered incorrectly.
Note
Swedish
Dynamic Range Control
5
Hint
Set the Disc Menu language.
TV Aspect
When you finish entering the code,
press [ENTER].
Video Out
Select a setting using
[Cursor U / D], then press [ENTER].
• You can only select the languages supported by the
inserted disc.
• The Audio Language setting may not be available
for some discs.
Your setting is activated.
Audio Language (Default: Original)
Set the Audio language.
DVD
Playback
Audio Language
TV Aspect
4:3 Letter Box
Original
Parental Lock
ALL
All
English
Disc Menu Language
English
French
Audio Language
Audio
Language
Subtitle Language
Original
Original
OFF
Spanish
DVD
German
Digital Out
Italian
Dynamic Range Control
ON
Swedish
Fast Forward with Audio
ON
OFF
Dutch
Video Out
Other
Select a setting using
[Cursor U / D], then press [ENTER].
Changing the Setting Menu
Your setting is activated.
If “Original” is selected, the audio language is the
default of the inserted disc.
Subtitle Language (Default: OFF)
Set the Subtitle language.
DVD
Playback
Subtitle Language
TV Aspect
4:3 Letter Box
OFF
OFF
Parental Lock
All
ALL
English
Disc Menu Language
English
French
Audio Language
Original
Spanish
Subtitle Language
OFF
German
Digital Out
DVD
Italian
Dynamic Range Control
ON
Swedish
Fast Forward with Audio
ON
OFF
Dutch
Video Out
Other
Select a setting using
[Cursor U / D], then press [ENTER].
Your setting is activated.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
59
Display Setting
1 In stop mode, press [SET UP].
2 Select “Advanced Setting Menu”
Audio Setting
Choose the appropriate Audio settings for your audio
equipment.
This will only affect DVDs playback.
using [Cursor U / D], then press
[ENTER].
1
2
If it has already appeared, proceed to step 3.
3
Select “Display” using
[Cursor U / D], then press [ENTER].
4
Select the desired item using
[Cursor U / D], then press [ENTER].
OSD Language (Default: English)
Set the OSD language.
See page 19 for details.
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
If it has already appeared, proceed to step 3.
3
Select “Playback” using
[Cursor U / D], then press [ENTER].
4
Select the desired item using
[Cursor U / D], then press [ENTER].
Note
VCR DVD
OSD Language
In stop mode, press [SET UP].
• The Dynamic Range Control function is available
only on discs recorded in the Dolby Digital format.
English
English
Deutsch
Digital Out
Italiano
Svenska
Nederlands
Set the digital audio output.
DVD
Playback
FL Dimmer (Default: Auto)
Set the front panel display brightness.
DVD
Digital Out
TV Aspect
4:3 Letter Box
PCM
48kHz
Parental Lock
ALL
All
Dolby Digital
Stream
Disc Menu Language
English
MPEG
PCM
Audio Language
Original
DTS
OFF
ON
Subtitle Language
OFF
Digital Out
Dynamic Range Control
ON
Fast Forward with Audio
OFF
ON
Video Out
Display
OSD Language
VCR DVD
FL Dimmer
English
Auto
FL Dimmer
Auto
Bright
Screen Saver
10
10minutes
minutes
Dark
VCR DVD
Select a setting using
[Cursor U / D], then press [ENTER].
Proceed with either of the following steps.
Select a setting using
[Cursor U / D], then press [ENTER].
Changing the Setting Menu
You can choose one from “Auto,” “Bright” and
“Dark.”
If “Auto” is selected, the display gets dark when
the power is off.
Digital Out - PCM
DVD
48kHz
48kHz
96kHz
Screen Saver (Default: 10 minutes)
Set the screen saver time delay.
DVD
Display
Screen Saver
OSD Language
English
OFF
FL Dimmer
Auto
Bright
55minutes
minutes
Screen Saver
10 minutes
10 minutes
minutes
10
DVD
15 minutes
Select a setting using
[Cursor U / D], then press [ENTER].
Your setting is activated.
30 minutes
Select a setting using
[Cursor U / D], then press [ENTER].
Your setting is activated.
5
Press [SET UP] to exit.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
60
PCM sampling (Default: 48kHz)
48kHz: If your amplifier / decoder is NOT compatible
with 96 kHz PCM, select “48kHz.” Sound
recorded at 96 kHz is down sampled to 48
kHz.
96kHz: If your amplifier / decoder is compatible with
96 kHz PCM, select “96kHz.” Sound is
sampled at 96 kHz.
Note
When playing back a disc with copyright protection:
• Even if you select “96kHz,” the sound is down
sampled to 48 kHz.
Settings for DTS (Default: ON)
DVD
Digital Out - DTS
ON
Dolby Digital conversion (Default: Stream)
Digital Out - Dolby Digital
OFF
DVD
PCM
Stream
Stream
Select a setting using
[Cursor U / D], then press [ENTER].
Your setting is activated.
Select a setting using
[Cursor U / D], then press [ENTER].
Your setting is activated.
PCM:
Converts the Dolby Digital into PCM
(2 channel.)
If your amplifier / decoder is NOT compatible
with Dolby Digital, set to “PCM.”
Stream: Outputs Dolby Digital signals.
If your amplifier / decoder is compatible with
Dolby Digital, set to “Stream.”
Hint
When playing back a DVD-RW disc recorded in VR
mode:
• If the audio source on a disc is in Dolby Digital
format, set “Dolby Digital” to “PCM” so that you can
switch to main audio (L), sub audio (R), or a
combination of both (L / R) using your amplifier /
decoder.
ON: Outputs DTS signals.
If your amplifier / decoder is compatible with
DTS, set to “ON.”
OFF: No DTS signal is output.
If your amplifier / decoder is NOT compatible
with DTS, set to “OFF.”
Dynamic Range Control (Default: ON)
Set to “ON” to make the dynamic range narrower.
Dynamic Range Control
4:3 Letter Box
ON
ON
Parental Lock
All
OFF
Disc Menu Language
English
Audio Language
Original
Subtitle Language
OFF
DVD
Digital Out
Dynamic Range
Range Control
Control
Dynamic
Fast Forward with Audio
ON
ON
ON
OFF
Video Out
Select a setting using
[Cursor U / D], then press [ENTER].
Your setting is activated.
The Dynamic Range Control function is effective
only with analogue audio connection.
Settings for MPEG (Default: PCM)
Digital Out - MPEG
DVD
Playback
TV Aspect
DVD
PCM
Stream
Fast Forward with Audio (Default: ON)
Set to “ON” to output the sound during DVD playback
at x1.5 fast forward.
DVD
Playback
Fast Forward with Audio
4:3 Letter Box
ON
ON
Parental Lock
All
OFF
OFF
Disc Menu Language
English
Audio Language
Original
Subtitle Language
OFF
DVD
Digital Out
Select a setting using
[Cursor U / D], then press [ENTER].
Dynamic Range Control
ON
Fast Forward with Audio
ON
OFF
Video Out
Your setting is activated.
Converts MPEG into PCM.
If your amplifier / decoder is NOT compatible
with MPEG, set to “PCM.”
Stream: Outputs MPEG Audio signals.
If your amplifier / decoder is compatible with
MPEG, set to “Stream.”
Select a setting using
[Cursor U / D], then press [ENTER].
PCM:
Downloaded From DvDPlayer-Manual.com JVC Manuals
Your setting is activated.
5
Press [SET UP] to exit.
EN
Changing the Setting Menu
TV Aspect
61
Parental level
All: All parental locks are cancelled.
8: DVD software of any grade (adult / general /
children) can be played back.
7 to 2: Only DVD software intended for general
use and children can be played back.
1: Only DVD softwares intended for children
can be played back.
DVD-Videos Parental Lock Level
Some DVD-Videos feature a parental lock function.
If the rating of the inserted disc exceeds the level you
set, playback will stop. You must enter a password
before the disc will be played back. This feature
prevents your children from viewing inappropriate
material.
1
2
A password is not yet set
Select “Yes” using [Cursor U / D],
then enter a new password using
[the Number buttons], then press
[ENTER].
In stop mode, press [SET UP].
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
Your setting is activated.
If it has already appeared, proceed to step 3.
3
4
If you select “No,” proceed to Step 5.
Select “Playback” using
[Cursor U / D], then press [ENTER].
A password is already set
Select “Parental Lock” using
[Cursor U / D], then press [ENTER].
Enter the current password using
[the Number buttons].
DVD
Playback
TV Aspect
4:3 Letter Box
Parental Lock
All
Disc Menu Language
English
Audio Language
Original
Subtitle Language
OFF
Parental Lock
DVD
Password Input
Digital Out
Dynamic Range Control
ON
Fast Forward with Audio
ON
OFF
Video Out
Note
Change the password.
• The parental lock function may not be available on
some discs.
• It may be difficult to determine if some DVDs
support the parental lock function. Be sure to
confirm that the parental lock function operates in
the way that you have set.
• Record the password in case you forget it.
Parental Lock
DVD
Change Password?
Yes
No
Parental Lock (Default: All)
Changing the Setting Menu
Set the parental lock level.
Change the parental lock level using
[Cursor U / D], then press [ENTER].
Proceed with either of the following steps.
Parental Lock
DVD
All
All
Your setting is activated.
If you press [ENTER] without entering a
password, you can set up without a password.
8
7
6
5
4
3
2
1
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
62
Select “Yes” using [Cursor U / D],
then enter a new password using
[the Number buttons], then press
[ENTER].
5
Press [SET UP] to exit.
Note
• Press [CLEAR] to erase numbers entered
incorrectly.
• If you forget your password or you want to clear all
settings in Parental Lock, enter [4], [7], [3], [7] using
[the Number buttons] at the option window. Your
password is cleared and parental levels are set to
“All.”
Changing Video Out System
Setting TV System
1
2
In stop mode, press [SET UP].
Select “Advanced Setting Menu”
using [Cursor U / D], then press
[ENTER].
If it has already appeared, proceed to step 3.
3
Select “Playback” using
[Cursor U / D], then press [ENTER].
4
Select “Video Out” using
[Cursor U / D], then press [ENTER].
5
6
Press [ENTER].
Select the desired system setting
using [Cursor U / D], then press
[ENTER].
Video Out - TV System
DVD
PAL
Auto
PAL:
Outputs a modified PAL signal for viewing
discs recorded with the NTSC system on a
PAL system TV.
Auto: Changes the video system (PAL / NTSC)
automatically according to the format of
the inserted disc.
7
Press [SET UP] to exit.
Note
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
Changing the Setting Menu
• With discs recorded using the PAL system, a PAL
signal is output for viewing on a PAL system TV.
• Discs recorded with the PAL system cannot be
viewed on an NTSC system TV.
• With discs recorded using the NTSC system, an
NTSC signal is output for viewing on an NTSC or
Multi system TV.
• With discs recorded using the NTSC system, select
PAL to view on a PAL system TV.
63
VCR Functions
Playback
Recording and One-Touch Timer
Recording (OTR)
VCR
1
Press [STANDBY/ON
the unit.
/I] to turn on
To play back a tape, turn on the TV and be sure to
select the input to which the unit is connected.
2
3
Press [VCR].
4
During playback, press [PAUSE p].
Insert a prerecorded tape, then press
[PLAY P] to begin playback.
Playback will be paused and sound will be muted.
5
6
7
Basic Recording
VCR
Before recording, make sure:
• The desired channel is selected by pressing the
number buttons on the remote control.
• There is a tape with a record tab in the unit.
• The desired recording speed is selected in SP
(standard play) or LP (long play) mode by pressing
[REC SPEED] on the remote control.
Press [PLAY P] to resume playback.
Tape speed
Press [STOP S] to stop playback.
Type of tape
Press [VCR STOP/EJECT S/O] on
the unit to eject the tape.
Note
• When a tape without record tab is inserted, the unit
will start playback automatically.
• Tracking will be automatically adjusted upon
playback. To adjust the tracking manually, press
[PR +/-].
Recording / Playback Time
E60
E120
E180
SP mode
1 hour
2 hours
3 hours
LP mode
2 hours
4 hours
6 hours
• Refer to page 29 for instructions on timer recording.
1
Turn on the unit and insert a
recordable tape.
Make sure that the TV input is set on the unit.
2
3
Press [VCR].
Select the recording speed using
[REC SPEED].
• The desired recording speed is selected in SP
(standard play) or LP (long play) mode by
pressing [REC SPEED].
VCR Functions
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
64
4
Select the desired channel to record
using [PR +/-] or [the Number
buttons].
5
Press [VCR REC I] to start
recording.
To temporarily stop recording or to resume it,
press [PAUSE p]. After the unit has been in
pause mode for 5 minutes, it will stop
automatically to protect the tape and the video
head from damage.
6
Press [STOP S] when the recording
is completed.
Accidental erasure prevention
To prevent accidental recording on a recorded
cassette, remove its record tab. To record on it later,
cover the hole with cellophane tape.
Search
Index Search
VCR
Record tab
One-Touch Timer Recording
1
2
Press [VCR].
3
Enter the number of recordings you
wish to skip using [the Number
buttons] within 30 seconds.
4
Press [FWD f] or [REV r] to start
index search.
VCR
This feature allows you to set the recording length
simply by pressing [VCR REC I].
1
Turn on the unit and insert a
recordable tape.
Make sure that the TV input is set on the unit.
2
3
Press [VCR].
4
Select the desired channel to record
using [PR +/-] or [the Number
buttons].
5
If you want to go in the forward direction, press
[FWD f].
If you want to go in the reverse direction, press
[REV r].
After index search, the VCR will play back the
tape automatically.
Select the recording speed using
[REC SPEED]. (See page 64.)
Press [VCR REC I] repeatedly until
the desired recording time (30
minutes to 8 hours) appears on the
TV screen.
Note
• This function is not available during recording.
• Every time a tape is recorded, an index mark is
written on the tape.
Time Search
One-touch timer recording will start.
0:30
(Normal Recording)
8:00
1:00
7:30
• When the unit reaches the specified time, it will be
turned off automatically.
• To change the recording length during one-touch
timer recording, press [VCR REC I] repeatedly
until the desired length appears.
• To cancel one-touch timer recording within the
specified time, press [STOP S].
Hint
• The remaining recording time will appear on the TV
screen during one-touch timer recording. Press
[ON SCREEN] to see it on the TV screen.
Downloaded From DvDPlayer-Manual.com JVC Manuals
VCR
This feature allows you to go to a specific point on a
tape by entering the exact amount of time you wish to
skip in order to reach the point.
1
2
Press [VCR].
3
Enter your desired time to skip using
[the Number buttons] within 30
seconds.
4
Press [FWD f] or [REV r] to start
time search.
Press [VCR SEARCH] repeatedly so
that the time search menu appears.
If you want to go in the forward direction, press
[FWD f].
If you want to go in the reverse direction, press
[REV r].
After time search, the unit will play back the tape
automatically.
Note
• This function is not available during recording.
• Press [STOP S] to stop the search.
• If the tape reaches the end during a Search, this unit
will cancel the search and rewind the tape.
EN
VCR Functions
Note
• If VCR one-touch timer recording is completed
during DVD playback or recording, the VCR will be
in stop mode and the DVD keeps the current mode.
• You cannot use the pause function during one-touch
timer recording.
• When one-touch timer recording is finished and the
power is turned off, the unit will switch to the timerstandby mode automatically if a timer recording has
] to cancel the
been programmed. Press [TIMER
timer-standby mode to use the unit continuously.
Press [VCR SEARCH] so that the
index search menu appears.
65
Other Operations
VCR
Press [VCR] first.
To cue or review picture during playback (Picture
Search):
Press [FWD f] or [REV r] during playback.
Press it again and the unit will search in super high
speed.
To freeze the picture on TV screen during
playback (Still mode):
Press [PAUSE p]. Each time you press the button,
the picture will be forwarded frame by frame.
If the picture begins to vibrate vertically during the still
mode, stabilize the picture by pressing the
[PR +/-].
If the picture is distorted or rolling vertically, adjust the
vertical hold control on your TV, if equipped.
Counter Reset:
Press [CLEAR].
To play back in slow motion:
Press [VCR SLOW ] during playback or the still
mode. Use [FWD f] or [REV r] to adjust the
speed.
If the noise bars appear on the TV screen, you can
reduce it by pressing [PR +/-].
Note
• Still / Slow / Pause mode will be automatically
cancelled after 5 minutes to prevent damage to the
tape and the video head.
• To return to play back from the Picture Search / Still /
Slow mode, press [PLAY P].
Changing the Video Colour
System
Different countries use different television colour
systems.
This unit will distinguish the video colour system
(MESECAM or PAL) automatically according to the
format of a prerecorded video tape during playback or
the input signal from the tuner or external devices.
To change the video colour system manually, press
[VCR SYSTEM].
Each time you press [VCR SYSTEM], the TV screen
will change as follows.
VCR Functions
AUTO
MESECAM
PAL
Note
• If the playback picture on the TV screen is black and
white, change the video colour system manually.
• When you change the video colour system
manually, be sure to change it before recording. If
you select the wrong video colour system for
recording, the colour of the picture may be
deteriorated.
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
66
Hi-Fi Stereo Sound System
This unit will record and playback Hi-Fi stereo sound.
This unit will receive stereo and bilingual broadcasts
and it is possible to record in several ways and to play
back the sound.
Selecting the Sound Mode
You can select each mode by pressing [AUDIO] on
the remote control. Each mode is indicated on the TV
screen as following.
• During reception of bilingual broadcasts
Mode
Audio output
Display on
the TV screen
Main
Main audio from the both
speakers
Main
Sub
Sub audio from the both
speakers
Sub
• Main audio from the left
speaker
• Sub audio from the right
speaker
Main
Sub
Main /
Sub
Note
• If you play back non-Hi-Fi tapes, the unit will play
back automatically in monaural even if you select
any mode.
• If the stereo signal becomes weak, the broadcast is
automatically recorded in monaural.
Others
Troubleshooting
Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing.
Some simple checks or a minor adjustment by you may eliminate the problem and restore correct operation.
DVD • VCR
Symptom
Remedy
The power does not turn on.
• Check the mains cable is connected securely.
• Check building circuit the breaker (in case of power failure.)
There is no picture.
• Check signal cables are connected securely.
• Check if a connecting cable is damaged.
• Check connections to your TV. (See page 17.)
• Switch the input selector on your TV (to “AV1,” for example) until a picture
appears on the screen.
TV programme picture does not fill the
screen.
• Set channels with “Auto Tuning” from the screen menu. (See page 19.)
• Select the channel of a TV programme using [PR +/-].
TV programme pictures are distorted.
• Adjust the direction of the TV antenna.
• Adjust the picture. (See the TV instruction manual.)
• Place the antenna and the TV farther apart.
• Separate any bunched antenna cables and the TV.
TV channel cannot be changed.
• Switch the TV input.
• Check if the antenna cable is connected correctly. (See page 17.)
The channel cannot be changed from the
channel you are recording.
• Set the TV input to “TV.”
Playback picture is distorted.
• Do not bring equipment that may cause electrical interference, such as a
cellular phone, near the unit.
The playback picture or TV programme from
equipment connected through the unit is
distorted.
• If a DVD player, VCR or tuner is connected to your TV via the unit, the copyprotection signal applied to some programmes could affect picture quality.
Disconnect the playback equipment in question and connect it directly to your
TV.
Nothing was recorded even though you set
the timer setting correctly.
• There was a power failure during recording.
• The unit’s internal clock stopped due to a power failure that lasted for more
than 30 seconds.
• Reset the clock. (See page 21.)
• Unplug the mains cable from the AC outlet and plug it in again.
• The programme contains copy protection signals that restrict copying.
• The timer setting overlapped with another setting that was set later or has
priority.
Timer recording is not complete or did not
start from the beginning.
• The timer setting overlapped with another setting that was set later or has
priority. (See page 32.)
• There was not enough disc space.
There is no sound.
• The disc is dirty or flawed.
• Check if all cables are connected securely.
• Check if a connecting cable is damaged.
• Check the connections to the amplifier input.
• Check if the input source setting on the amplifier is correct.
• Check if the recorder is in Pause mode or in Slow-motion Playback mode.
• Check if the recorder is in Fast Forward or Fast Reverse mode.
Timer recording is not possible.
• Make sure
[TIMER
icon appears on the front panel display of this unit. If not, press
].
• Batteries are exhausted.
• There are obstacles between the remote control and the unit.
• The remote control is too far from the unit.
• There are no batteries in the remote control.
• The unit is not turned on.
• The remote control is not pointed at the remote sensor on the unit.
• Press [DVD] or [VCR], whichever you need. Then, try again.
The unit does not operate correctly.
• If static electricity or anything else causes the unit to operate abnormally,
unplug the mains cable and plug it in again.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Others
The remote control does not function.
EN
67
DVD
Symptom
Remedy
There is no picture.
• If the setting menu display appears, press [SET UP] or [RETURN] to turn off
the display.
Picture noise appears.
• The disc is dirty or flawed.
• If the unit is connected to your TV via a VCR, or if it is connected to a
combination TV / VIDEO player, the copy-protection signal applied to some
DVD programmes could affect picture quality. If you still experience this
problem even when you connect the unit directly to your TV, try connecting the
unit to your TV’s S-VIDEO input.
Sound is noisy.
• The disc is dirty or flawed.
The unit does not play back the disc.
• No disc is inserted.
• A blank disc is inserted.
• The disc is upside down. Insert the disc with the labeled side facing up.
• The disc is not correctly inserted.
• The unit cannot play back certain discs (such as a CD-ROM.) (See page 37.)
• The region codes on the DVD-Video and the unit are not matched. (See page
37.)
• Moisture has condensed inside the unit. Remove the disc and leave the unit
turned on for about two hours until the moisture evaporates. (See page 3.)
• The unit cannot play back the disc if it was recorded on another recorder and
not finalised. (See page 36.)
There is no sound.
• If the audio signal is not output from the COAXIAL DIGITAL AUDIO OUT jack,
check the Audio setting. (See page 60.)
Playback image freezes for a moment.
• During the playback of a two layered disc, the picture may freeze for a moment
while playback switches from the first to the second layer. This is not a
malfunction.
The unit does not play back the disc from the
beginning.
• Resume playback is activated. (See page 41.) Press [STOP S] twice.
• You have inserted a disc whose title menu or DVD menu automatically
appears on the TV screen when it is first inserted.
The unit starts playing back the disc
automatically.
• The DVD-Video features an auto playback function.
Some functions such as Stop, Search, or
Slow-motion Playback cannot be performed.
• Depending on the disc, you may not be able to perform some of those
operations. See the instruction manual supplied with the disc.
The language for the sound track cannot be
changed.
• Multilingual tracks are not recorded on the DVD-Video, DVD-R, or DVD-RW
being played back.
• The DVD-Video prohibits the changing of the language for the sound track.
• Try changing the language using the DVD-Video menu.
The subtitle language cannot be changed or
turned off.
• Multilingual subtitles are not recorded on the DVD-Video.
• The DVD-Video prohibits changing the subtitles.
• Try changing the subtitles using the DVD-Video menu.
Angles cannot be changed.
• Multi-angles are not recorded on the DVD-Video being played back.
• You can change the angle only if the disc contains multi-angle scene. Angles
can be changed only when the multi-angle scene appears on the screen.
• The DVD-Video prohibits changing angles.
• Try changing the angle using the DVD-Video menu.
Recording does not start immediately after
pressing [DVD REC I].
• An unused DVD-R or DVD-RW was inserted. It takes a while for the unit to
automatically format a DVD-RW.
Recording does not stop immediately after
you press [STOP S].
• It will take a few seconds for the unit to send data to disc before recording can
stop.
The disc tray does not open when you press
[OPEN/CLOSE/EJECT O].
• It may take a few seconds for the disc tray to open after you have recorded or
edited a disc.
• This is because the unit is sending data to the disc.
“Repairing” appears on the display.
• If a power failure occurs or the mains cable is unplugged during recording,
finalising, formatting or editing (even after “Wait for a moment.” message
disappeared), a repairing process will begin automatically when the unit is
turned on next time.It may take several minutes up to about four hours.
Others
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
68
VCR
Symptom
Remedy
Picture noise appears.
• Adjust tracking control for better picture by pressing [PR +/-] while you are
playing back a video tape.
• Head cleaning for VCR may be necessary. Refer to “AUTO HEAD CLEANING.”
The unit does not play back the tape.
• No video tape is inserted.
Recording does not start immediately after
pressing [VCR REC I].
• Make sure the video tape has a record tab when you record to a video tape. If
needed, cover the hole with cellophane tape.
The remote control does not function.
• Check if a video tape is in the unit. Press [VCR]. Then, try again.
The motor rotates even when playback /
recording is stopped.
• The motor may rotate for the duration of approximately 5 minutes for efficient
operation. This is not a malfunction.
*If the above remedies do not solve the problem, please call the service centre for help.
Others
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
69
Error message
Cause
Solution
Disc Error
— Please eject the disc. —
Playback feature may not be
available on this Disc.
• An unplayable disc is inserted in the unit.
• The disc is upside down.
• Insert a standard disc shown in “Playable
Discs.” (See page 37.)
• Insert the disc with the labelled side facing
up.
Region Error
— Please eject the disc. —
Playback is not authorized in
your region.
• Playback is not authorized in the region of
the DVD-Video that you inserted in the
unit.
• Insert a DVD-Video with region codes 2 or
ALL.
Parental Lock On
The current selected parental
level prohibits playback.
• The current selected parental level in the
setting menu prohibits playback.
• Check the Parental Lock setting. (See
page 62.)
Recording Error
This programme is not allowed
to be recorded.
• The recording function encountered a
copy prohibited programme.
• Original source is in NTSC system.
• You cannot record copy prohibited
programmes.
• This unit cannot record an NTSC signal.
Recording Error
This programme is not
recordable in Video mode.
• You are trying to record a copy-once
programme onto a DVD-RW disc in Video
mode.
• Set “DVD-RW Recording Format” to “VR
mode.” (See page 25.)
Recording Error
Cannot record on this disc.
• You are trying to record onto a disc that is
unrecordable, or the disc status does not
satisfy recording requirements.
• The disc is dirty.
• The disc is damaged.
• Insert a recordable disc, and ensure the
disc status satisfies the recording
requirements. (See page 23.)
• Clean the disc with a cleaning cloth.
• Replace the disc.
Recording Error
This programme is not allowed
to be recorded on this disc.
• You are trying to record a copy-once
programme onto a DVD-RW disc that is
not compatible with CPRM.
• Insert a ver. 1.1 or ver. 1.2 DVD-RW disc
(compatible with CPRM.)
Recording Error
This disc is protected and not
recordable.
• You are trying to record onto a disc that is
set as protected in the Disc Setting menu.
• Remove the disc protect setting in the Disc
Setting menu. (See page 35.)
Recording Error
Disc is full.
(No area for new recording)
• You are trying to record onto a disc that
has no space for recording.
• Insert a recordable disc with enough
recording space.
• Delete unnecessary titles from an original
list. (See page 52.)
Recording Error
You cannot record more than 99
titles on one disc.
(The maximum is 99)
• You are trying to record onto a disc on
which the number of recorded titles has
reached the maximum (99.)
• Delete unnecessary titles. (See pages 49
and 52.)
Recording Error
You cannot record more than
999 chapters on one disc.
(The maximum is 999)
• You are trying to record onto a disc on
which the number of recorded chapters
has reached the maximum (999.)
• This unit cannot delete the chapter
markers in the original list. To delete
unnecessary chapter markers, use other
DVD recorders.
• Delete unnecessary titles from an original
list. (See page 52.)
Recording Error
You cannot record on this disc as
Control Information is full.
• This disc has no space to write Control
Information when recording or deleting
contents.
• When editing has been repeatedly
performed, the control information area
may become full even though the
recording area has enough space.
• Delete unnecessary titles. (See pages 49
and 52.)
Recording Error
You cannot record on this disc as
Power Calibration Area is full.
• When recordings are performed
repeatedly onto an unstable disc, this area
may become full.
• Every time you insert a disc for recording,
part of the disc's working area will be used.
• If you repeat this frequently, it will be used
up quicker and you may not be able to
record full 99 titles.
• Insert a new disc.
Recording Error
This disc is already finalised.
• You are trying to record onto a disc that is
already finalised.
• Release the finalising for the disc. (See
page 36.)
*If you are still having trouble with the unit after checking all the Troubleshooting points, write down the error code
and the error description and consult your dealer or an authorized service centre.
Others
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
70
Language Code
Language
Code
Language
Code
Language
Code
Language
Code
Abkhazian
4748
French
5264
Lithuanian
5866
Sindhi
6550
Afar
4747
Frisian
5271
Macedonian
5957
Singhalese
6555
Afrikaans
4752
Galician
5358
Malagasy
5953
Siswat
6565
Albanian
6563
Georgian
5747
Malay
5965
Slovak
6557
Amharic
4759
German
5051
Malayalam
5958
Slovenian
6558
Arabic
4764
Greek
5158
Maltese
5966
Somali
6561
Armenian
5471
Greenlandic
5758
Maori
5955
Spanish
5165
Assamese
4765
Guarani
5360
Marathi
5964
Sundanese
6567
Aymara
4771
Gujarati
5367
Moldavian
5961
Swahili
6569
Azerbaijani
4772
Hausa
5447
Mongolian
5960
Swedish
6568
Bashkir
4847
Hebrew
5569
Nauru
6047
Tagalog
6658
Basque
5167
Hindi
5455
Nepali
6051
Tajik
6653
Bengali;Bangla
4860
Hungarian
5467
Norwegian
6061
Tamil
6647
Bhutani
5072
Icelandic
5565
Occitan
6149
Tatar
6666
Bihari
4854
Indonesian
5560
Oriya
6164
Telugu
6651
Bislama
4855
Interlingua
5547
(Afan) Oromo
6159
Thai
6654
Breton
4864
Interlingue
5551
Panjabi
6247
Tibetan
4861
Bulgarian
4853
Inupiak
5557
Pashto; Pushto
6265
Tigrinya
6655
Burmese
5971
Irish
5347
Persian
5247
Tonga
6661
Byelorussian
4851
Italian
5566
Polish
6258
Tsonga
6665
Cambodian
5759
Japanese
5647
Portuguese
6266
Turkish
6664
Catalan
4947
Javanese
5669
Quechua
6367
Turkmen
6657
Chinese
7254
Kannada
5760
Rhaeto-Romance
6459
Twi
6669
Corsican
4961
Kashmiri
5765
Romanian
6461
Ukrainian
6757
Croatian
5464
Kazakh
5757
Russian
6467
Urdu
6764
Czech
4965
Kinyarwanda
6469
Samoan
6559
Uzbek
6772
Danish
5047
Kirghiz
5771
Sangho
6553
Vietnamese
6855
Dutch
6058
Kirundi
6460
Sanskrit
6547
Volapuk
6861
English
5160
Korean
5761
Scots Gaelic
5350
Welsh
4971
Esperanto
5161
Kurdish
5767
Serbian
6564
Wolof
6961
Estonian
5166
Laothian
5861
Serbo-Croatian
6554
Xhosa
7054
Faroese
5261
Latin
5847
Sesotho
6566
Yiddish
5655
Fiji
5256
Latvian; Lettish
5868
Setswana
6660
Yoruba
7161
Finnish
5255
Lingala
5860
Shona
6560
Zulu
7267
Others
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
71
Glossary
Analogue audio
An electrical signal that directly
represents sound. In contrast,
digital audio can also be an
electrical signal, but is an indirect
representation of sound. See also
Digital audio.
DTS
(Digital Theater System)
DTS is a Multi-channel surround
sound system, but it is different from
Dolby Digital. Both formats were
developed by Digital Theater
System, Inc.
Aspect ratio
The width of a TV screen relative to
its height. Conventional TVs are 4:3
(i.e., the screen is almost square.)
Widescreen models are 16:9 (the
screen is almost twice as wide as its
height.)
Finalise
To make DVDs that have been
recorded playable in DVD players. It
is possible to finalise DVD-R / DVDRW discs with this unit.
Chapter
Just as a book is split up into
several chapters, a title on a DVD
disc is usually divided into chapters.
See also Title.
CM SKIP
This unit can skip TV commercials
during DVD-Video playback. Once
[
] is pressed, the start point will
be set forward 30 seconds and
playback resume automatically.
(You can press [
] up to 6 times.)
CPRM
(Content Protection for
Recordable Media)
CPRM is a scrambling copy
protection system for the protection
of “copy-once” broadcast
programmes (e.g. some satellite
broadcasts.)
Digital audio
An indirect representation of sound
using numbers. During recording,
the sound is measured at discrete
intervals (44 or 100 times a second
for CD audio) by an analogue-todigital converter, generating a
stream of numbers. On playback, a
digital-to-analogue converter
generates an analogue signal
based on these numbers. See also
Sampling frequency and Analogue
audio.
JPEG
(Joint Photographic Experts
Group)
JPEG is a method of compressing
still image files. You can copy JPEG
files on CD-RW / R discs from a
computer and play back the files on
this unit.
MP3
(MPEG Audio Layer 3)
MP3 is a method of compressing
files. You can copy MP3 files on CDRW / R discs from a computer and
play back the files on this unit.
PBC (Video CD only)
(Playback Control)
This function enables you to play
back interactive software using a
menu screen. See also Title.
PCM
(Pulse Code Modulation)
PCM is a format that converts audio
into digital data. It is mainly used for
Audio CDs and DAT. This unit can
play back sounds as realistic as
possible by converting even
compressed Dolby Digital and
MPEG audio to PCM.
Playlist
From this list you can play back
contents of a disc in your desired
order or in sequence. It is also
possible to directly search for a
specific scene.
Dolby Digital
A system developed by Dolby
Laboratories that compresses
digital sound. It works with stereo
(2ch) or multi-channel audio.
Others
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
72
Region code
Regions associate discs and
players with particular areas of the
world. This unit will only play back
discs that have compatible region
codes. You can find the region code
of your unit by looking on the rear
panel. Some discs are compatible
with more than one region (or all
regions.)
Sampling frequency
The rate at which sound is
measured by a specified interval to
turn it into digital audio data. The
number of samples in one second is
defined as the sampling frequency.
The higher the rate is, the better the
possible sound quality.
S-Video output
Video is output as the individual
signals of colour(C) and
luminance(Y), so a higher-quality
picture will be displayed.
Title
(DVD)
A collection of chapters on a DVD.
See also chapter.
(Video CD)
The contents of a Video CD. When
playing back a Video CD with the
PBC function, the title menu will
appear automatically.
Track
Audio CDs and Video CDs use
tracks to divide the contents of a
disc. The DVD equivalent is called a
chapter. See also Chapter.
Specifications
General
System
DVD-Video, DVD-RW / R, DVD+RW / R, CD-DA, CD-RW / R,
Video Cassette Tape
VCR video heads
Four heads
Power requirements
220–240 V
Power consumption
35 W (standby: 5.0 W)
Weight
4.3 kg
± 10%, 50 Hz ± 0.5%
Dimensions (width x height x depth)
435 x 99.5 x 262 mm
Operating temperature
5°C to 40°C
Operating humidity
Less than 80% (no condensation)
TV format
PAL B / G
Recording
Recording format
Video Recording format (DVD-RW only),
Video format (DVD-RW, DVD-R)
Recordable discs
DVD-ReWritable, DVD-Recordable
Video recording format
Sampling frequency
Compression format
13.5 MHz
MPEG
Audio recording format
Sampling frequency
Compression format
48 kHz
Dolby Digital
Tuner
Receivable channels
E2-E69
Note
• The specifications and design of this product are subject to change without notice.
Declaration of Conformity
This product complies with the requirement of the directives
EMC-Directive:
89 / 336 / EEC
Low Voltage Directive:
73 / 23 / EEC
CE Marking:
93 / 68 / EEC
We declare that the following product:
DVD Video Recorder & Video Cassette Recorder, Model DR-MV2SEU
is in compliance with following Regulations.
EN55013: 2001+A1:2003, EN55020: 2002+A1:2003,
EN61000-3-2: 2000, EN61000-3-3: 1995 + A1: 2001
EN60065: 1998
EN60825-1 Edition 1.2: 2001
Others
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
73
Downloaded EN
From DvDPlayer-Manual.com JVC Manuals
74
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
75
EN
DR-MV2SEU
© 2005 Victor Company of Japan, Limited
Downloaded From DvDPlayer-Manual.com JVC Manuals
Printed in China
EU 0905TNH-FN-FN
E9770ED/1VMN?????*****
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement