HALFORDS 12 FUNCTION
CYCLE COMPUTER
umeb12halfe2 # 英文
CONTENTS DESCRIPTIONS (See Fig. A)
1. LCD DISPLAY
2. MODE BUTTON
3. BATTERY CAP
4. SET BUTTON
5. 1 st or 2 nd BIKE SELECTION BUTTON
8.RUBBER SPACER
9. BRACKET
10. SENSOR
11. MAGNET
12. MAGNET COLLAR
7. SENSOR PAD 14. CABLE TIES
SCREW
INSTALLATION
SENSOR and MAGNET MOUNTING
1. Mount the SENSOR l on the front fork with the SENSOR PAD i with the sensor facing the spokes. (See Fig. B)
2. Mount the MAGNET on one spoke of the front wheel with the magnet facing and level with the SENSOR. (See Fig. C). Place the MAGNET
COLLAR over the nut and check for alignment before firmly tightening the magnet screw .
3. Adjust the relative position between the sensor and the magnet.
Make sure the GAP between the magnet and the sensor is within 4mm (1/6
inch). (See Fig. D)
Adjust the gap by moving both the magnet and the sensor up or down.
4. Do not cut off any excess sensor band until all adjustments have been made
& correct computer operation has been checked and is functioning correctly.
(See Fig. E)
BRACKET MOUNTING
Attached the bracket to the handlebar and fit with pad, use the two cable ties to mount the bracket, do not tighten the cable ties before the bracket is place at the right position.
SECURING THE SENSOR CABLE
1. Select suitable positions to clip the sensor cable to the fork with CABLE TIES. (See Fig. G)
2. Make sure the sensor cable is loose enough for the handlebar to turn freely before tightening the cable ties.
3. Secure excess wire near the fork crown by wrapping it around the front brake cable or by gathering excess cable and securing it with cable ties.
MAIN UNIT MOUNTING
Before mounting the main unit install battery-see battery installation/change
1. Mount the main unit onto the bracket by sliding it from front to rear till it clicks into position. (See
Fig. H)
2. This bracket is designed with a lock lever. It can lock up the main unit, ensuring that the main unit will not drop out while riding.
3. To remove the main unit, press down on the lock lever of the bracket then pull the main unit forward and off.
FUNCTIONS
SPD: Current Speed
The current speed is always displayed on the upper set when riding. It displays current speed up to 199.9 Km/H or 120.0 Mile/H.
ODO1, ODO2 Bike1 Odometer, Bike2 Odometer
1. The odometer accumulates total distance as long as the cycle is being ridden.
2. This computer design has 2 wheel circumference memories to calculate data for 2 bikes. The odometer is separate for each bike.
3. It displays one ODO data only when the bike is selected in the current status.
T-TM: Total Riding Time
The T-TM accumulates total riding time while riding the bike1 or bike2.
T-ODO: Total Odometer
The T-ODO is the sum of the ODO1 plus ODO2.
12HR or 24HR Clock
Displays the current time either in 12HR or 24HRs.
AVG: Average Speed
1. This is calculated by dividing DST by the TM. The average data counted is from the last RESET to current point.
2. It will display “0.0” when TM is less than 4 seconds.
3. It is updated about one second when TM is over 4 seconds.
4. It display an “Err” symbol when either the TM is over 100 hours or the
DST is over 1.000 Km (or miles). Reset the unit in order to restart.
DST: Trip Distance
The DST function accumulates the distance data from the last RESET operation as long as the bike is being ridden.
TM: Riding Time
1. The TM totals the riding time from the last RESET operation.
2. It will automatically begin counting upon riding, and continue to count for
3 seconds after the cycle has stopped to confirm that no more signal is being sent.
The computer reverses back the over counted 3 seconds automatically.
3. It displays in 0.1 second increments when TM is less than 1 hour and changes to 1 second increments after 1 hour. It will restart from zero after 100 hours.
MAX: Maximum Speed
It shows the highest speed from the last RESET operation.
DST/D: Distance Today
The DST/D function accumulates the distance data for one day ride. The data will be cleared at PM 12.00.00 (0.00.00) automatically.
/ : Speed Pacer
Th e speed pacer arrow flashes up when the current speed is higher than the average speed and flashes down when lower than the average speed.
BUTTON OPERATION AND NORMAL OPERATION
MODE BUTTON d
Press this button to move in loop sequence from one function screen to another.
SET BUTTON f
Press this button to get in or out of the setting screens when you want to reset to bike1, bike2 circumference or the current time of the clock.
1st or 2nd BIKE SELECTION BUTTON g
1. This computer has 2 sets of circumference memories to calculate 2 bikes data separately.
2. Press 1 ST OR 2 ND BIKE SELECTION BUTTON g to switch between bike1 and bike2.
MAIN UNIT SET UP (ALL CLEAR)
INITIATE THE COMPUTER & UNIT SELECTION (See Fig. 1)
1. Install battery (refer to Battery Installation / Change).
2. Hold down the MODE button d and the 1 st or 2 nd BIKE SELECTION
BUTTON g simultaneously for more than 3 seconds to activate the computer and clear all data. IMPORTANT: Be sure to activate the computer before use otherwise the computer may run errors.
3. All the LCD segments will be tested automatically after the unit is initiated.
4. Press MODE button d to stop LCD test, then the flashing “Km/h” is displayed for unit selection
5. Press MODE button d to choose Km/h or Mile/h.
6. Press the SET BUTTON f to store selection.
2. Unit will change to the normal operation after the circumference is set.
12 HR CLOCK
SETTING (See Fig. 4)
1. Press the MODE button d until the display changes to “CLK”.
2. Press the SET button f to enter the clock adjusting screen.
3. A quick press of the MODE button d to select 12HR or 24HR.
4. Adjust the clock data as the data setting procedures.
RESET OPERATION (See Fig. 5)
1. Hold down the MODE button d until the LCD digit is cleared, then release it. The computer will reset the RT, MAX, AVG, and DST data from stored values to zero.
2. It cannot reset CLK and ODO data.
ODO1, ODO2 and T_TM DATA SETTING (See Fig. 2)
1. The function is designed to re-key in former data of ODO1, ODO2 and T-TM when the battery is replaced. A new user does not need to set this data.
2. Each press of the SET button skips one setting data process.
3. Data setting Process:
• The data is changed by adjusting each digit separately. The digit being changed flashes.
• Quickly press the MODE button d to increase the digital value by 1.
• To change the setting digit, hold down the MODE button d for more than 2 seconds.
• Press the SET button f to store the data and change to the next setting or the normal operation.
WHEEL CIRCUMFERENCE
Identify the tyre size of your cycle and key in the corresponding number shown in the following chart.
WHEEL CIRCUMFERENCE
DATA SETTING (See Fig. 3)
1. To set the correct wheel data quickly press the MODE button d this will change the first digit one level at a time, when this number is correct hold down the MODE button d for 3 seconds this will set the digit and move onto the next.
Press the SET button f to store the data.
* Refer to the chart below to calculate the setting value.
AUTOMATIC START/STOP
1. The computer will automatically begin counting data upon riding and stop counting data when riding is stopped.
2. The flashing symbol “ ” indicates that the computer is at start status.
POWER AUTO ON/OFF
To preserve battery power the computer will automatically switch off when it has not been used for approx. 4 mins. The computer will restart by either riding or pressing the MODE button d.
REPLACING THE BATTERY (See Fig. I)
1. The Symbol “ ” will appear to indicate the battery is nearly exhausted.
2. Replace the battery with a new one within 2 weeks after the symbol has appeared, otherwise incorrect data may be displayed.
BATTERY INSTALLATION/CHANGE
Note:- All data will be cleared when battery is replaced. This computer allows you to re-key in the ODO1, ODO2 and T-TM data which you rode before replacing the battery. So if wish to reinstall this information it should be recorded before removing the old battery.
1. Remove the old battery.
2. Replace with a new LR44 battery (See Fig. I) or equivalent in the compartment on the back of the computer with the positive (+) pole towards the battery cap.
3. Activate the main unit again.
TROUBLE SHOOTING
Check the following before taking unit in for repairs.
PROBLEM CHECK ITEMS
No Display 1. Is the battery dead?
2. Is there incorrect battery installation?
No current speed or incorrect data
1. Is it at the recalibrating or
12HR clock setting screen?
2. Are the contacts between the main unit and bracket poor?
3. Are the relative positions and gap of sensor and magnet correct?
4. Is the wire broken?
5. Is the circumference correct?
Irregular
Display
LCD is black
Display is slow
Did you leave main unit under direct sunlight when not riding the bike for a long time.
Is the temperature below 0 0
(32 0 F)?
C
REMEDY
1. Replace the battery.
2. Be sure that the positive pole of the battery is facing the battery cap.
1. Refer to the adjusting procedure and complete the adjustment.
2. Wipe contacts clean.
3. Refer to (FIG.C&D) and readjust data correctly.
4. Repair or replace wire.
5. Refer to “calibration” and enter correct value.
Refer to the MAIN UNIT SETUP and activate the computer again.
Place main unit in the shade to return to normal state.
No adverse effect of data.
Unit will return to normal state when the temperature rises.