FORWARD-STOP-REVERSE SWITCH ! INSTALLATION INSTRUCTIONS Part No. 9485

FORWARD-STOP-REVERSE SWITCH ! INSTALLATION INSTRUCTIONS Part No. 9485
INSTALLATION INSTRUCTIONS
FORWARD-STOP-REVERSE SWITCH Part No. 9485
for Model KBRC-240D
!
SaFetY Warning! Please read carefully before proceeding.
This product must be installed and serviced by a qualified technician, electrician, or electrical maintenance person familiar with its operation and the hazards involved. Proper installation, which includes electrical connections, fusing or other current protection, and grounding, can reduce the chance of electrical shocks, and/or fires, in this product or products used with this product, such as electric motors, switches, coils, solenoids, and/or relays. Do not use
this drive in an explosion-proof application. Eye protection must be worn and insulated adjustment tools must be used when working with drive under power.
This product is constructed of materials (plastics, metals, carbon, silicon, etc.) which may be a potential hazard. Proper shielding, grounding, and filtering
of this product can reduce the emission of radio frequency interference (RFI) which may adversely affect sensitive electronic equipment. It is the responsibility of the equipment manufacturer and individual installer to supply this Safety Warning to the ultimate end user of this product. (SW 8/2012)
Figure 1 – mounting the
ForWard-StoP-reVerSe SWitch
deScriPtion
The Forward-Stop-Reverse Switch assembly is designed for installation on
the front cover of the KBRC-240D. It is used to provide electronic reversing
for the KBRC-240D. The Forward-Stop-Reverse Switch assembly contains
a white/yellow wire, a white/green wire, and a white/red wire which are
terminated with 0.25” female quick-connect terminals.
RUBBER BOOT
SWITCH BUSHING
FRONT COVER
mounting
1. Remove the hole plug that covers the
FORWARD-STOP-REVERSE position. Use the
Hole Plug Removal Instructions that are provided.
1. Remove the violet Main Speed Potentiometer
wire that is installed on the +15V terminal of the
KBRC-240D PC board. Using pliers, gently rock
the female terminal back and forth horizontally
while pulling it upward.
2. Install the violet wire from the Main Speed
Potentiometer assembly (removed in step 1)
to the center terminal of the Forward-StopReverse Switch assembly. See Figure 2.
MAIN SPEED POTENTIOMETER
VIOLET
ORANGE (SIG)
WHITE (COM)
WHITE/RED (-15V)
VIOLET
WHITE/YELLOW (+15V)
TRQ SPD
J6
1.7A
2.5A
5A
7.5A
10A
eLectricaL connectionS
TO START/STOP SWITCH
SIG RET START STOP
2. Align the switch key in the front cover and mount
the Forward-Stop-Reverse Switch assembly
with the rubber boot. Use the hex wrench that is
provided to tighten the rubber boot hex nut.
Do not overtighten. See Figure 1.
Figure 2 – connection diagram
EN COM COM +15V -15V
!
SWITCH BODY
Warning! Make sure that the AC line is disconnected before
installing the Forward-Stop-Reverse Switch assembly.
J4
EN
J11
FORWARD-STOP-REVERSE SWITCH
3. Install the white/yellow wire from the
Forward-Stop-Reverse Switch assembly to the
+15V terminal of the KBRC-240D PC board. See Figure 2.
4. Install the white/red wire from the Forward-Stop-Reverse Switch assembly to the -15V terminal of the KBRC-240D PC board.
See Figure 2.
KB eLectronicS, inc.
12095 NW 39th Street, Coral Springs, FL 33065-2516 • (954) 346-4900 • Fax (954) 346-3377
Outside Florida Call toll Free (800) 221-6570 • e-mail – [email protected]
www.kbelectronics.com
(A40134) – Rev. C – 4/2015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement