Midmark VetPro 1000 Veterinary Dental Cart

Midmark VetPro 1000  Veterinary Dental Cart
Midmark VetPro® 1000
Veterinary Dental Cart
Model Numbers:
8000-001
8000-002
8000-003
8000-004
8000-005
8000-006
8000-006S
8000-007
8000-007S
8000-008
8000-008S
SF-1928
Service and
Parts Manual
Present Production Model Shown
FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY
Part No. 004-0586-00 Rev (4/19/16)
[Revised: dd/mo/yr]
Checking for Air Leaks...........B-2
Water Relay..............................B-3
Tri-block....................................B-4
Line Voltage.............................B-5
Compressor Head....................B-7
Capacitor..................................B-8
Check Valve & Solenoid........B-10
Pressure Switch.....................B-12
Air Regulator..........................B-14
Air Tank .................................B-16
Water System.........................B-17
Air Intake Filter......................B-18
Exhaust Muffler......................B-20
Foot Control...........................B-21
LED Light (Scaler).................B-22
Standard Scaler.....................B-23
Air/Oil Separator....................B-24
Fiber Optics (Early Units).....B-25
Fiber Optics (Current)...........B-26
Handpiece Holder Adjust......B-28
Foot Control...........................B-29
ii
Section C
Section D
Compression Cycle.................A-2
Electrical ..................................A-3
Troubleshooting Chart............A-5
Section E
Section A General Information
Troubleshooting
Testing & Adjustments
Section B
Table of Contents
© Midmark Corporation 2008 SF-1928
Symbols...................................... iii
Ordering Parts........................... iii
Serial Number Location............ iii
Specifications............................ iv
Model Description..................... iv
Scheduled Maintenance............. v
Warranty Information................ vi
Access procedures
Upper Compartment................C-2
Middle Compartment...............C-3
Lower Compartment................C-3
Water System...........................C-5
Delivery System.......................C-6
Wiring & Tubing diagrams
Wiring Diagram...................... D-2*
Tubing Diagrams................... D-7*
Tri-Block Diagram................ D-12*
Quad-Block Diagram.............D-13
exploded views & parts lists
VetPro® 1000.............................E-2
(*) Indicates multiple pages due to model / serial number break(s).
General Information
© Midmark Corporation 2008 SF-1928
Symbols
Ordering Parts
warning
Indicates a potentially hazardous situation which
could result in serious injury if not avoided.
Caution
Indicates a potentially hazardous situation which may result in minor or moderate injury if not avoided. It may
also be used to alert against unsafe practices
Equipment Alert
Indicates a potentially hazardous situation which could result in equipment damage if not avoided.
The symbols below may be used in this manual to represent
the operational status of table functions and components.
Indicates the function / component is working properly.
No action required.
Indicates the function / component is working,
but a problem exists.
Indicates the function is not working at all, or that the component is faulty.
The following information is required when ordering parts:
• Serial number & model number
• Part number for desired part
(Refer to Section E: Exploded Views & Parts Lists)
Non-warranty parts orders may be faxed to Midmark using
the Fax Order Form.
For warranty parts orders, call Midmark’s Technical Service
Department with the required information.
Hours: 8:00 am to 5:00 p.m. EST (Monday thru Friday)
Phone: 1-800-Midmark
Serial Number Location
Serial Number
Label
Past Production Model Shown
[Revised: dd/mo/yr]
iii
Go To Table Of Contents
Specifications
Cart
Width
23 inches (58.42 cm)
Length
18 1/2 inches (46.99 cm)
Height
36 1/2 inches (92.71 cm)
Weight
130 lbs (58.97 kg)
Shipping Weight
150 lbs (68.04 kg)
Top of Cart Weight Restriction
25 lbs (11.33 kg)
Electrical (See Regulatory Compliance Chart - Next Page)
Fuse (Scaler Transformer)
800mA, 250 V, 3AG SLO BLO
Power Cord Length
10 ft. Hospital Grade
Handpiece
Connection Type
Midwest 4-Hole Type Handpiece
Compressor
warning
Equipment not suitable for use in the presence of
a flammable anesthetic mixture.
Motor
Oil Free 1/3 HP
Working Pressure
70-100 PSI
Flow Rate
2.5 scfm @ 40 PSI
Sound Level (full load)
40 dB
Air Tank
1 Gallon
Water Module
Reservoirs
Two - 1 Liter - Toggled
Pressurized System
30-40 PSI
Handpiece Flush System
Manual
Air and Water Connections
External Quick Connects
Other
Duty Cycle
Continuous Operation
Note: Exception, Units with LED
Scaler, 10 min. ON, 5 min. OFF
Classifications
Class 1, Type B Applied Part,
Ordinary Equipment [IPXO]
warning
The Acteon Newtron® LED scaler complies with current electromagnetic compatibility standards. However, it must not be used by or on those with cardiac stimulators or other active implants unless adequate electromagnetic interference shielding is present. Check with a cardiologist to verify the EMI shielding capabilities of the implant. See
enclosed Newtron® LED manual for further advisories.
© Midmark Corporation 2008 SF-1928
[Revised: 2/14/14]
iv
Go To Table Of Contents
Model Identification / Compliance Chart
Complies To:
Model
Description
Electrical Ratings:
UL
60601-1,
Ed. 1
CAN / CSA22.2,
#601.1-M90
IEC 60601-1,
Ed. 2
CE
•
•
•
•
•
•
VAC
+/- 10%
Amps
Cycles
(Hz)
•
•
115
6
60
115
6
60
8000-001
VetPro 1000 w/ Scaler
8000-002
VetPro 1000 w/o Scaler
8000-003
VetPro 1000 w/ Scaler and Fiber
Optics
•
•
•
•
115
6
60
8000-004
VetPro 1000 w/o Scaler and w/
Fiber Optics
•
•
•
•
115
6
60
8000-005
VetPro 1000 w/ Scaler, Export
•
230
3
50
8000-006
VetPro 1000 w/ LED Scaler and
Fiber Optics. Export
•
230
3
50
8000-007
VetPro 1000 w/ LED Scaler and
2 Position Fiber Optics
•
•
•
•
115
6
60
8000-008
VetPro 1000 w/ LED Scaler and
Fiber Optics
•
•
•
•
115
6
60
8000-006S
VetPro 1000 w/ LED Scaler and
Swivel Fiber Optics. Export
•
230
3
50
8000-007S
VetPro 1000 w/ LED Scaler and
2 Position Swivel Fiber Optics
•
•
•
•
115
6
60
8000-008S
VetPro 1000 w/ LED Scaler and
Swivel Fiber Optics
•
•
•
•
115
6
60
Note
Refer to Section E For Serial Number Breaks
© Midmark Corporation 2008 SF-1928
[Revised: 11/03/15]
v
Scheduled Maintenance Chart
Scheduled Maintenance
Interval
Inspection / Service
Daily
Clean System
Refer to: Operating and Care Guide Tri-fold or CD, located in sleeve inside door on back of cart.
Drain Air Regulator
Refer to: Operating and Care Guide Tri-fold or CD, located in sleeve inside door on back of cart.
Drain Condensation from
Air Tank
Refer to: Operating and Care Guide Tri-fold or CD, located in sleeve inside door on back of cart.
Empty Water System
Refer to: Operating and Care Guide Tri-fold or CD, located in sleeve inside door on back of cart.
After Each Procedure
Annually
Description
Clean Handpieces
Follow manufacturer’s of handpieces recommendations.
Flush Handpieces
Refer to: Operating and Care Guide Tri-fold or CD, located in sleeve inside door on back of cart.
Fill Water Bottles
Refer to: Water Bottles in this manual.
Change Mufflers
and
Air Regulator Filter
Refer to: Mufflers and Air Regulator in this manual.
Date of Service:
Model Number:
Location:
Serial Number:
Service Technician:
Notes:
© Midmark Corporation 2008 SF-1928
[Revised: dd/mo/yr]
vi
General Information
Warranty Information
SCOPE OF WARRANTY
Midmark Corporation (“Midmark”) warrants to the original purchaser its Exam Room Casework, Veterinary products and components (except for components not warranted under “Exclusions”) manufactured by Midmark to be free from defects in material and workmanship under normal interior use and service. Midmark’s
obligation under this warranty is limited to the repair or replacement, at Midmark’s option, of the parts or the products the defects of which are reported to Midmark
within the applicable warranty period and which, upon examination by Midmark, prove to be defective.
APPLICABLE WARRANTY PERIOD
The applicable warranty period, measured from the date of delivery to the original user, shall be as follows:
The VetPro® 1000 is warranted against defect in material and workmanship for a period of two years from the time of delivery.
EXCLUSIONS
This warranty does not cover and Midmark shall not be liable for the following; (1) repairs and replacements required because of misuse, abuse, negligence,
alteration, accident, freight damage, or tampering; (2) changes in color caused by natural or artificial light; (3) products which are not installed, used, and properly
cleaned as required in the Midmark written “Installation” and or “Installation/Operation” Manual for this applicable product; (4) products considered to be of a
consumable nature such as light bulbs and surge suppression product; (5) accessories or parts not manufactured by Midmark; (Any warranties on these items are
extended
directly by the manufacturer of these items to the original purchaser. Information on these manufacturers’ warranties will be enclosed with the applicable products.
Also, Midmark will furnish copies of any of the warranties extended by any such manufacturers upon request.) (6) specially manufactured products; (7) Damage
caused by animals; (8) charges by anyone (including Midmark’s authorized dealers) for adjustments, repairs, replacement parts, installation, or other work performed upon or in connection with such products which is not expressly authorized in writing in advance by Midmark.
EXCLUSIVE REMEDY
Midmark’s only obligation under this warranty is the repair or replacement of defective parts. Midmark shall not be liable for any direct, special, indirect, incidental,
exemplary or consequential damages or delay including, but not limited to, damages for loss of profits or loss of use.
NO AUTHORIZATION
No person or firm is authorized to create for Midmark any other obligation or liability in connection with the products.
THIS WARRANTY IS MIDMARK’S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. MIDMARK MAKES NO
IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. THIS
WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS.
© Midmark Corporation 2008 SF-1928
[Revised: dd/mo/yr]
vii
© Midmark Corporation 2008 SF-1928
viii
Section A
© Midmark Corporation 2008 SF-1928
Operation &
Troubleshooting
[Revised: dd/mo/yr]
A-1
Operation & Troubleshooting
Compression Cycle.............................A-2
Electrical .............................................A-3*
Troubleshooting Chart.........................A-5
Compression Cycle & Air Flow
Atmospheric air is drawn in through the intake filter to the compressor head
where air is compressed and exhausted. Air travels though the check valve,
which prevents air flushing back into the head, then flows through the
solenoid. The solenoid allows air to escape for approximately two seconds
during start-up to relieve pressure from the head, then closes sending
pressurized air to the storage tank. Air from the storage tank activates the
pressure switch. As the storage tank fills the pressure switch opens at a
preset pressure and stops the compressor.
The air regulator adjusts air from the storage tank to 65 PSI. Storage tank air
also supplies the quick disconnect. Air going to the quick disconnect is not
regulated and pressure is at 100 PSI. Accessories connected to the quick
disconnect will need to have it’s own regulator installed if the manufacture
recommends less than 100 PSI.
The regulated air (65 PSI) flows to the foot control and water bottles. When
user activates the throttle valve by depressing the foot control, air is sent
through the tri-block and each instrument manifold. When the instrument
is removed from the holder the holder valve is activated allowing air to flow
through the handpiece. There are drive air adjustment valves to adjust air
pressure for the instruments.
The air/water syringe is activated by pressing on the instrument’s air and
water buttons. The user can make drive air, coolant air and water flow
adjustments. Air flows though the gauge to show pressure readings.
Regulated air also pressurizes the water bottles. Air to the water bottles
is adjusted to 40 PSI by the water pressure regulator and can be
lowered by adjusting the water pressure regulator.
Water Flow
VetPro® 1000 has a self-contained water system with two, one-liter bottles. The toggle switch opens and closes the use of the bottles. When the toggle switch is set in the middle, both valves to the bottles are closed
depressurizing the bottles and stopping flow. When toggle switch is flipped
toward a bottle that bottles valve opens and allows water flow to each needle
valve’s instrument. The needle valve is the users way to control water flow to
instruments.
VA1245
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 03/20/12]
A-2
Always verify model & serial number
Electrical Flow
• Supply line voltage is always present
at the Dental Cart power cord receptacle
when plugged into a wall receptacle.
When the On/Off switch is turned on, line
voltage, 115 VAC, is supplied to the
Terminal Block and Pressure Switch.
• 115 VAC comes from the Terminal Block
and energizes the Accessory Receptacles,
Timer, Motor, Fan and Transformer.
•The Timer keeps the solenoid turned
off until the compressor is running at full
RPM. The Solenoid is normally opened
when not energized. The Solenoid allows
air to escape for approximately two
seconds to relieve pressure from the
head, then closes sending pressurized
air to the storage tank.
• The system will continue to run until
the pressure inside the system reaches
100 PSI (+ / - 5 PSI) (Cut-out time)
It will turn back on at 65 PSI (+ / - 5 PSI)
(Cut-In time).
• When the Pressure Switch is at
65 PSI (+ / - 5 PSI) or below it’s
contacts are closed and the compressor
is energized.
• Transformer supplies 24 VAC to Scaler
(if applicable).
Models:
Serial Numbers:
All
All
TGC001000Thru TGC001254
V796868 thru V933242
© Midmark Corporation 2008 SF-1928
[Revised: 8/9/10]
A-3
Always verify model & serial number
Electrical Flow - Current Units
• Supply line voltage is always present at the
Dental Cart power cord receptacle when plugged
into a wall receptacle. When the On/Off switch is
turned on, line voltage, 115 VAC, is supplied to
the Terminal Block and Pressure Switch.
• 115 VAC comes from the Terminal Block and
energizes the Timer, Motor, Fan and Transformer.
•The Timer keeps the solenoid turned off until the
compressor is running at full RPM. The Solenoid
is normally opened when not energized. The
Solenoid allows air to escape for approximately
two seconds to relieve pressure from the head,
then closes sending pressurized air to the storage tank.
• The system will continue to run until the
pressure inside the system reaches
100 PSI (+ / - 5 PSI) (Cut-out time)
It will turn back on at 65 PSI (+ / - 5 PSI)
(Cut-In time).
• When the Pressure Switch is at
65 PSI (+ / - 5 PSI) or below it’s contacts are
closed and the compressor is energized.
• Transformer supplies 24 VAC to Scaler
(if applicable).
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Please refer to Section D
for Wire Diagrams Listed Under Serial Numbers
[Revised: ]
A-4
Always verify model & serial number
Troubleshooting Chart
Problem
Syringe has no
water when button
depressed.
Probable Cause
Check
Correction
Empty water bottles.
Water level in bottles.
Fill water bottles.
Toggle not seated to
right or left side.
Check toggle location.
Push toggle completely to left or right side.
Water Regulator
Check Water regulator.
Verify bottles are pressurized. Regulator should be adjusted all the way
to the right.
Quick disconnect.
Check water (blue)
disconnect.
Depress quick disconnect with a screwdriver and hold for serveral
seconds. Hold rag underneath screwdriver for any water flow. If no water
flow, change syringe check valve.
Tubing Crimped.
Check for crimped tubing.
Replace tubing.
Syringe.
Check Syringe tip and
cartridge.
Change syringe tip. Check syringe cartridge for water, repair or replace.
Check needle valves.
Verify needle valves are open.
Remove handpieces and verify you have water
through tubing.
If you have water coming from syringe, remove handpieces and recheck
water flow from tubing, if none repair or replace handpieces.
Kinked Tubing.
Check for kinked tubing from foot control to water
relay.
Replace tubing.
Water Relay
Remove air tubing from foot control going to water
relay, depress foot control and check for air.
If air is present, repair water relay membrane or replace water relay.
Refer to: Section B Water Relay.
Remove water tubing from tri-block coming from
water relay, depress foot control.
If water is present, repair or replace tri-block. If no water is present,
repair or replace water relay. Refer to: Section B Tri-Block or Water
Relay.
Incorrect holder
location.
Check location of handpiece.
Place handpiece in correct holder position.
Membrane
(Diaphragm)
If foot control is not depressed while handpieces
are hanging in holders, membrane in (tri or dual)
block is leaking.
Change membrane (diaphragm) in block.
Refer to Section B Tri-Block.
Water bottle or toggle
leaking.
Check valve.
Check, check valve.
Toggle over to one side and fill water bottle. Observe other side for leaking. If it is leaking , replace check valve. Repeat for other side.
Handpiece in holder
and is still running
when another handpiece is in use.
Handpiece in wrong
holder.
Verify handpiece is in correct holder position.
Move handpiece to correct position.
Holder switch out of
adjustment.
Check set screw adjustment.
Adjust set screw on holder. Refer to Section B: Handpiece Holder
Adjustment.
Tri-block.
Check air to tri-block supply.
Pinch tubing off with pliers, handpiece should stop, if not check pilot
valve.
Handpiece has no
Needle Valves closed.
water flow but
Handpieces.
syringe is still working.
Handpiece leaking in
holder.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 5/21/13]
A-5
Always verify model & serial number
Troubleshooting Chart
Problem
Probable Cause
Check
Correction
Power cord unplugged.
Verify power cord is plugged in cart and outlet.
Plug power cord into cart and/or outlet.
On/Off switch is off.
Check that the on/off switch is turned on.
Turn on/off switch on.
Circuit breaker tripped.
Check to see if circuit breaker needs reset.
Reset circuit breaker.
No power at outlet.
Check for voltage at outlet and/or move to
another room.
Reset circuit breaker. Assure outlet is on dedicated circuit
capable of handling cart requirements.
Loose wire connection.
Check back panel wire connections.
Reconnect wires to back panel if loose.
Check voltage on circuit breaker, power cord bracket and
on/off switch. Refer to: Section B Line Voltage
Capacitor.
Check Capacitor.
Test capacitor. Replace if needed.
Refer to Section B: Capacitor
Pressure Switch Frozen
Check Pressure Switch.
Replace Pressure Switch. Refer to: Section B Pressure
Switch.
Motor/Compressor Frozen
Unplug cart. Can you manually move
compressor fans?
If you are unable to move compressor fans, replace compressor. Refer to: Section B Compressor
Compressor will not shut off or will
recycle often.
Air leaks in system and/or
foot control.
Check for air leaks.
Refer to: Section B Checking for Air Leaks
Compressor will not recycle or
stalls and or breaker tripping
causing air to deplete.
Room temperature too high. Ambient room temperature.
Move to another room. Try running unit.
Check Valve.
See if check valve is sticking.
Spray soapy water on solenoid muffler, if it bubbles while
compressor is running, replace check valve.
Refer to: Section B Check Valve
Solenoid.
Check Solenoid.
Turn off unit and drain air tank. Turn on unit and see if
solenoid bubbles for a few seconds, if not replace solenoid.
Refer to: Section B Solenoid
See if check valve is sticking.
Spray soapy water on solenoid muffler, if it bubbles while
compressor is running, replace check valve.
Refer to: Section B Check Valve
LED light not installed
properly.
Check polarity.
Check polarity ( + & - ) connection of LED bulb.
Refer to: Section B LED Scaler
Tubing connection bad.
Check tubing connection.
Check continuity between tubing connection and scaler
plug. Refer to: Section B LED Scaler
Poor contact with pins.
Clean pins.
Clean pins with alcohol and allow to dry before use.
Compressor will not start.
Compressor makes humming noise To much back pressure.
and or smells like it is burning.
LED light not working on scaler.
(Models 8000-007, 8000-007S, 8000008 & 8000-008S ONLY)
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: [11/03/15]
A-6
Always verify model & serial number
Troubleshooting Chart
Problem
Probable Cause
Scaler running intermittently or low
power, or not vibrating for no
apparent reason.
Poor power supply
connection.
Check
Check power supply.
Correction
Verify VetPro 1000 is plugged into wall and not loose.
Air pressure not set Check air pressure.
correctly.
Check air pressure. Refer to: Section B Air Regulator
Not drive air.
Check drive air adjustment knob.
Verify Drive air adjustment knob is all the way open.
Tubing.
Check tubing continuity.
Check continunity in black and orange wires of the tubing.
Refer to: Section B Scaler Tubing
Check HI resistance.
Check HI resistance between the black and orange tubing
wires. Refer to: Section B Scaler Tubing
Tip not tight enough.
Check tip.
Verify tip is tightened. Tip must be tightened for scaler
operation to work.
Tip is worn.
Check tip.
Tip must be within tolerance as per tip chart for scaler
operation to work. Change tip.
Potentiometer Harness bad
or misadjusted.
Check for proper setting. Service tip: if setting
is correct move on to Ώ check.
If you have 24 V AC or 31 V DC, Check potentiometer for
proper resistance sweep of 4 to 4.7K Ώ when turned from
Min to Max on Ohmmeter measuring between the white
and brown/blue wires on molex.
If resistance is not ok, replace potentiometer harness. If
resistance is ok, check all wiring and pins for continuity.
Repair any wiring that does not pass continuity check.
If you do not have 24V AC or 31 V DC Check power supply and air/electric switch for failure.
Replace potentiometer harness if power supply or airelectric switch has failed.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Tubing is damaged.
Check tubing.
Check continuity in black and orange wires of the tubing.
Refer to: Section B Scaler Tubing
Handpiece is damaged.
Swap out handpieces.
If scaler operates properly with different handpiece, old
one is damaged.
Transducer in scaler.
Check transducer in scaler.
Replace with a known working handpiece. If the replacement handpiece works, then the transducer is bad in
the problem handpiece. Return handpiece to Acteon for
service or replace with new handpiece.
All
all
[Revised: 5/21/13]
A-7
Always verify model & serial number
Section B
Testing & Repair
© Midmark Corporation 2008 SF-1928
[Revised: dd/mo/yr]
B-1
Component / System
Checking for Air Leaks........................B-2
Water Relay.........................................B-3
Tri-block...............................................B-4
Line Voltage........................................B-5
Compressor Head...............................B-7
Capacitor.............................................B-8
Check Valve & Solenoid......................B-10
Pressure Switch..................................B-12
Air Regulator.......................................B-14
Air Tank ..............................................B-16
Water System......................................B-17
Air Intake Filter....................................B-18
Exhaust Muffler...................................B-20
Foot Control........................................B-21
LED Light............................................B-22
Standard Scaler..................................B-23
Air/Oil Separator..................................B-24
Fiber Optic (Early units).....................B-25
Fiber Optic (Current units)...................B-26
Handpiece Holder Adjustment.............B-28
Foot Control........................................
Testing & Repair
Checking for Leaks
Refer to:
Use Soapy Water to check for leaks...
A)
B)
C)
D)
E)
F)
G)
H)
I)
Listen to foot control for air leaks.
Tubing inside back of cart.
Air regulator and “T” fittings.
Storage air tank and tank fittings.
Tri-block and instrument manifolds.
Air and water quick disconnects.
Handpiece docks.
Water bottles.
Solenoid muffler, check valve and compressor fittings.
Page
Access Procedures.............................C-1
Quick Disconnects
Note: Refer to: Section C for Access Procedures
Foot
Control
Air Tank & Fittings
Regulator & Fittings
Tubing
Tri-Block
& Manifolds
Handpiece
Docks
Solenoid & Check Valve
Compressor Fittings
VA1252
Water Bottles
Earlier Production Model Shown
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 5/21/13]
B-2
Always verify model & serial number
Testing & Repair
Water Relay - Function and Location
Refer to:
The water relay is located inside the delivery panel.
The water relay stops the water flow to the needle valves until the foot control (throttle valve) is pressed,
then air flows to the water relay and opens the needle valves allowing water to flow to the instruments. It
also supplies water directly to the syringe.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Earlier Production Model Shown
All
all
[Revised: dd/mo/yr]
B-3
Page
Access Procedures.............................C-1
Tubing Diagram...................................D-1
Exploded Views & Parts List...............E-1
Always verify model & serial number
Testing & Repair
Refer to:
Step 1: Disconnect power.
Remove delivery panel.
Water Relay - Testing
Page
Access Procedures.............................C-1
Tubing Diagram...................................D-1
Exploded Views & Parts List...............E-1
Note: Refer to Section C Access Procedures
Step 2: Disconnect orange tubing from water relay .
Depress foot control.
Foot Control
Tube
Incoming
Water
Supply
Tri-block
Manifold
Tube
Syringe
Tube
Results
Step 3: Disconnect tubing from water relay manifold.
Depress foot control.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Status
Required Action
No water when foot control not
depressed.
Water flow good.
Water when foot control is
depressed.
Water flow good.
No air flow when orange tube is
disconnected.
Tubing clogged or damaged. Change
orange tubing.
No water flow when manifold
tubing is disconnected.
Water relay is bad. Replace water
relay.
All
all
[Revised: 5/21/13]
B-4
Always verify model & serial number
Testing & Repair
Tri-Block (Dual Block in Models without Scaler 8000-002 & -004)
Refer to:
Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Function and Location
The tri-block is located behind the delivery instruments.
It is a manifold that the air and water source travel through and is routed to different components in the delivery system. When the foot control is activated, air
flows into the tri-block through two tubes, one for coolant air and one for drive air.
Coolant air flows from the tri-block to each instrument manifold. Drive air flows
though the adjustment valve on the tri-block to each instrument. The tri-block also
supplies air to the air pressure gauge.
Water flows from the water relay valve through the tri-block and to each water
needle valve. The tri-block has a membrane seal that provides a fluid-tight seal
between the two walls. To access the membrane for repair, remove allen screws
from the front of the block to separate the block. Also Refer to: Section C Access
Procedures to access the block and to Section D for a tubing diagram of the
tri-block. Replacement kit for the membrane is available.
Note: The air/water supply for the syringe does not flow through the tri-block.
Membrane
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: dd/mo/yr]
B-5
Always verify model & serial number
Testing & Repair
Line Voltage Testing - 115 VAC
Refer to:
Components to check line voltage are listed in the chart below.
115 VAC Models Only Reference Serial Numbers Below
Meter Reading
Status
Required Action
< 115 VAC On / Off Switch
Replace On / Off Switch
< 115 VAC Pressure Switch
Replace Pressure Switch
< 115 VAC Terminal Block
Replace Terminal Block
< 115 VAC Fiber Optic
Receptacles
Replace Receptacle
< 115 VAC Timer
Replace Timer
< 115 VAC Fan
Replace Fan
< 115 VAC Transformer
Replace Transformer
115 VAC = On / Off Switch
On / Off Switch OK
115 VAC = Pressure Switch
Pressure Switch OK
115 VAC = Terminal Block
Terminal Block OK
115 VAC = Fiber Optic
Receptacles
Accessory Receptacles OK
115 VAC = Timer
Timer OK
115 VAC = Fan
Fan OK
115 VAC = Transformer
Transformer OK
Models:
Serial Numbers:
All
TGC001000Thru TGC001254
V796868 thru V933242
[Revised: 8/9/10]
Caution
When testing components with power
on use care to prevent electrical shock.
To check line voltage...
Set multi-meter to v
Use multi-meter to verify voltage.
All
© Midmark Corporation 2008 SF-1928
Page
Pressure Switch..................................B-12
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
B-6
Always verify model & serial number
Testing & Repair
Line Voltage Testing - 230 VAC
Refer to:
Components to check line voltage are listed in the chart below.
230 VAC Models Only
Reference Serial Numbers Below
Meter Reading
<230VACOn/OffSwitch
<230VACPressureSwitch
<230VACTerminalBlock
< 230 VAC Timer
< 230 VAC Fan
< 230 VAC Transformer
<230VACFiberOpticReceptacle
230=VACOn/OffSwitch
230=VACPressureSwitch
230=VACTerminalBlock
230 = VAC Timer
230 = VAC Fan
230 = VAC Transformer
231=VACFiberOpticReceptacle
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Status
Page
Pressure Switch..................................B-11
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Caution
When testing components with power
on use care to prevent electrical shock.
To check line voltage...
Set multi-meter to v
Use multi-meter to verify voltage.
Required Action
ReplaceOn/OffSwitch
ReplacePressureSwitch
ReplaceTerminalBlock
ReplaceTimer
ReplaceFan
ReplaceTransformer
ReplaceReceptacle
On/OffSwitchOK
PressureSwitchOK
TerminalBlockOK
Timer OK
Fan OK
Transformer OK
FiberOpticReceptacleOK
All
V933243 thru Present
[Revised: 8/9/10]
B-7
Always verify model & serial number
Testing & Repair
Refer to:
Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Compressor Rebuild .......642648A_0605
Compressor Head - Function and Location
The Compressor Head is located in the lower compartment.
Atmospheric air is drawn in though the intake filter to the compressor head where air is compressed
and exhausted to the storage tank. Heat is generated from the compression process. The compressor
head has a fan on both ends. There is also a fan located above the compressor head to pull hot air up
and out though a vent on the back middle compartment of the cart. If you are unable to manually move
the fans on the compressor (when power supply is completely shut-down), the compressor head needs
replaced. There is a head rebuild kit available.
Compressor Head
Earlier Production Model Shown
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Intake Filter
All
all
[Revised: 09/24/08]
B-8
Always verify model & serial number
Testing & Repair
Refer to:
Capacitor - Function and Location
The capacitor is located in the lower compartment.
The run capacitor aids in running efficiency. It creates
a phase shift to give more power to the compressor.
Capacitor
Earlier Production Model Shown
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: dd/mo/yr]
Page
Test Capacitor.....................................B-9
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
B-9
Always verify model & serial number
Testing & Repair
Capacitor - Testing
Step 4: Place meter probes on capacitor connectors.
Reverse the leads, this should produce the same reading.
Step 1: Disconnect power.
Access run capacitor in lower compartment.
Note: Refer to: Section C - Lower Compartment.
Step 2: Discharge capacitor by touching screwdrivers
to both contacts on the capacitor and to each other.
Step 3: Set meter to Ω reading.
Meter Reading
Status
Required Action
“O” or “Open” Reading
Replace Capacitor
Start Low and Increases
Capacitor
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: dd/mo/yr]
B-10
Always verify model & serial number
Testing & Repair
Refer to:
Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Check Valve & Solenoid - Function and Location
The check valve and solenoid are located in the lower compartment.
Compressed air travels from the compressor head though the check valve,
which prevents air flushing back into the head. Then air flows though the
solenoid. The solenoid allows air to escape for approximately two seconds
to relieve pressure from the head then closes sending pressurized air to the
storage tank.
Earlier Production Model Shown
Solenoid
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Check Valve
All
all
[Revised: dd/mo/yr]
B-11
Always verify model & serial number
Testing & Repair
Refer to:
Check Valve - Clean
Step 1: Disconnect power.
Step 2: Remove check valve from compressor head and solenoid.
Step 3: Blow out valve with air.
If valve is sticking, replace.
VA1261
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
All
all
[Revised: dd/mo/yr]
B-12
Always verify model & serial number
Testing & Repair
Refer to:
Pressure Switch- Function and Location
The pressure switch is located in the middle compartment accessed from
the back of the cart. When the storage tank is filled to the preset pressure
the pressure switch will open and stop the compressor.
Cut-In / Cut-Out time is the minimum and maximum discharge pressures at
which the compressor will switch from unload to load operation (cut-in) or
from load to unload (cut-out). The pressure switch controls the Cut-In and
Cut-Out times.
Pressure Switch
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: dd/mo/yr]
Page
Pressure Switch Adjustment...............B-13
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
B-13
Always verify model & serial number
Testing & Repair
Pressure Switch - Adjustment
Step 2: If compressor didn’t shut down at 100 PSI,
access pressure switch and remove cover.
Step 1: Run compressor until pressure reaches 100 PSI.
Note: Compressor should shut off close to 100 lbs.
Adjustment Screw “A”
Note: Refer to: Section C Middle Compartment
Adjustment Screw “B”
Step 3: Make adjustment.
• Adjustment screw “A” , turn clockwise to increase both Cut-In and Cut-Out pressure.
• Differential pressure adjustment screw “B”, turn Clockwise to increase Cut-In pressure without affecting Cut-Out.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: dd/mo/yr]
B-14
Always verify model & serial number
Testing & Repair
Refer to:
Air Regulator - Function and Location
The regulator is located in the upper compartment behind the rear door.
The air regulator regulates air from the storage tank from 100 PSI to 65 PSI. The regulator
should only be set for 65 PSI. There is a button on the bottom of the regulator that will drain
condensation by pressing on it at the end of each work day.
Air Regulator
Earlier Production Model Shown
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: dd/mo/yr]
Page
Air Regulator Adjustment....................B-15
Air Regulator Maintenance..................B-16
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
B-15
Always verify model & serial number
Testing & Repair
Refer to:
Page
Air Regulator Maintenance..................B-16
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Air Regulator- Adjustment
Equipment alert
Do not adjust regulator over 65 PSI, it will overheat the compressor. Air
pressure for the piezo electric scaler should
be set to 60 PSI.
Decrease
To Adjust Regulator...
A)
B)
C)
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Increase
Adjustment
Knob
Unlock
Pull adjustment knob upward to unlock.
Rotate adjustment knob clockwise to
increase pressure, counterclockwise to
decrease pressure.
Push adjustment knob downward to lock.
Lock
All
all
[Revised: dd/mo/yr]
B-16
Always verify model & serial number
Testing & Repair
Refer to:
Air Regulator & Air Tank - Maintenance
To Drain Air Regulator...
Place a cloth under the regulator and depress
the button until there is no water coming out.
Page
Air Regulator Adjustment....................B-15
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Present Model Shown with Yellow Tubing
Earlier Models have Red Tubing
Note
User should drain regulator and air tank daily.
Button
Valve
Opened
To Drain Condensation from Air Tank...
VA1238
A) Turn
power switch off.
B) Position end of yellow tube so it drains into a container.
C) Turn drain valve slowly to open.
D) When no water is coming out, slowly close valve.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 6/16/10]
B-17
Always verify model & serial number
Testing & Repair
Refer to:
Water System - Function and Location
The self-contained water system has two, one-liter bottles located on the front panel
under the instruments. It is recommended to use only distilled water in the bottles. The
water bottles supply water to the instruments that use water and to the quick disconnect
on the back of the cart. Air flows through the water regulator to pressurize the water
bottles. The water regulator is located between the water bottles and is set at 40 PSI.
Use the water needle valve to adjust water flow for each instrument.
There is a toggle valve between the water bottles, which controls which water bottle
will supply water. When the toggle is in the center neither water bottles is pressurized.
Move the toggle toward the left to pressurize the left bottle and depressurize the right
bottle. Toggle to the right to pressurize the right bottle and depressurize the left bottle.
Water Regulator
Toggle
Water Bottles
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 03/20/212]
Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
B-18
Always verify model & serial number
Testing & Repair
Refer to:
Page
Clean Air Intake Filter..........................B-19
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Air Intake Filter - Function and Location
Atmospheric air is drawn in though the intake filter before
flowing to the compressor head. The intake filter protects the
head from dust and debris and should be changed annually.
Earlier Production Model Shown
Air Intake Filter
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: dd/mo/yr]
B-19
Always verify model & serial number
Testing & Repair
Refer to:
Page
Air Intake Filter - Function & Location.B-18
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Air Intake Filter - Clean
Step 1: Remove filter housing from cap by pushing in and turning.
Filter
Housing
Step 2: Remove filter and clean by blowing out or replace as needed.
Install new filter in housing to cap on compressor head.
Install cover on lower compartment. Note: Air Intake Filter should be changed annually.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: dd/mo/yr]
B-20
Always verify model & serial number
Testing & Repair
Refer to:
Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Exhaust Muffler
The exhaust muffler provides lower sound (dba) levels for the
VetPro® 1000. The exhaust muffler can be cleaned using a rag and
should be replaced annually. Exhaust Muffler
Earlier Production Model Shown
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: dd/mo/yr]
B-21
Always verify model & serial number
Testing & Repair
Refer to:
Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Foot Control Replacement........003-1899-00
Foot Control- Function and Location
The foot control opens a throttle valve that allows air flow to the instrument manifolds.
The syringe is not controlled by the foot control. It is operated by the hand controls on
the syringe itself.
There is a foot control storage bracket on the back of the unit to hang the cord on when
the cart is not in use or when moving the cart to a new location.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 08/06/08]
B-22
Always verify model & serial number
Testing & Repair
LED Scaler
To check polarity..
Verify + on the LED ring and the handpiece are the same side.
Check and Test
LED (+)
LED (-)
To test continuity...
Set meter to Ω and check connections.
PIN 1 is wired to Black wire of Molex Plug. (Ultrasound Signal)
PIN 2 is wired to White wire of Molex Plug. (LED Power)
PIN 3 is wired to Blue wire of Molex Plug. (LED Power)
PIN 4 is wired to Orange wire of Molex Plug. (Ultrasound Signal)
Meter Reading
Status
Required Action
“O” or “Open” Reading
(Continunity Check)
Replace Scaler Cord
0.1 - 1.0 Ohms
(Continunity Check)
Scaler Cord OK
Voltage within specs when
measured at LED Ring
(Test Tubing Connections)
Handpiece, tubing and module OK
Voltage out of specs at
LED Ring Pins
(Test Tubing Connections)
Tubing pin Voltage ok - Replace Handpiece
Molex Plug Voltage ok and NOT at Tubing Pins - Replace Tubing
Models:
--Set meter to V. With no LED in socket, voltage reading will
be approximately 21 VDC. With LED inserted, voltage
reading will be approximately 12 or 14 VDC measured at
pins on the blue and white wire on molex plug.
Note: This requires thin probes to make contact.
8000-007, -008
Serial Numbers:
© Midmark Corporation 2008 SF-1928
To test in the tubing connection...
all
[Revised: dd/mo/yr]
B-23
Always verify model & serial number
Testing & Repair
Refer to:
To test continuity...
Scaler Tubing
Set meter to Ω.
Check orange wire of molex to the center pin of tubing.
Check right side (as shown) pin of tubing to the black wire in molex.
Testing
Page
Access Procedures.............................C-1
Tubing Diagrams.................................D-1
Exploded Views & Parts List...............E-1
Note: Refer to: Section D Wire Diagrams
Check To Orange
Wire
Check To
Black Wire
Note
Only check for HI resistance
if scaler is experiencing
intermittent or low power.
To check HI resistance...
• Set ohmmeter for 20 MEG OHM scale. If using a manual setting meter or just “OHMS” if auto ranging meter.
• Disconnect handpiece from tubing.
• Disconnect molex from module.
• Without touching probe leads with fingers, place the meter leads across the orange and black wires in molex. There
should be (Open Circuit). Any reading other than this indicates a HI Resistance short in tubing and needs to be replaced.
Meter Reading
Models:
8000-001, 003, -005, -006
Serial Numbers:
© Midmark Corporation 2008 SF-1928
all
[Revised: 6/7/12]
B-24
Status
Required Action
0.1 - 1.0 Ohms
(Continunity Check)
Tubing OK
“O” or “Open”
Reading (Continunity
Check)
Change Tubing
Always verify model & serial number
Testing and Repair
Air / Oil Separator- Cleaning
The air/oil separator (exhaust collector) acts as an exhaust muffler and oil collector
(gauze). When gauze becomes saturated it must be replaced.
Note
User should check air/oil separator periodically.
To clean the air/oil separator...
A)
B)
C)
D)
E)
Turn master ON/Off switch Off.
Remove air/oil separator container.
Dispose of the fluid and saturated gauze.
Disinfect container and mounting cap.
Install clean gauze and reinstall the container.
VA1676i
Models:
Serial Numbers:
All
V1043398 thru Present
© Midmark Corporation 2008 SF-1928
[Revised: dd/mo/yr]
B-25
Always verify model & serial number
Testing & Repair
To check voltage...
A) Verify voltage at power supply connection to optic controller (stablizer) is 3-4 VAC.
B) With foot pedal depressed, wire connections at optic controller (stablizer).
C) Verify voltage is 2.9 - 4.1 VAC.
D) Remove instrument from tubing, remove bulb (pry out) from tubing.
E) Check voltage at bulb wire connectors on tubing end. Verify voltage is 2.9 - 4.1 VAC.
Fiber Optic
(Earlier Production
Verify SN )
Refer to:
Page
Access Procedures........C-1
Tubing Diagrams............D-1
Exploded Views ............E-1
Testing
Note
Optic
Controller
(Stablizer)
If the voltage is out of spec at the Optic Controller (Stablizer), check the air tubing
for air flow. If no air flow, check for a kink in the line. Repair and restore air flow, then
recheck voltage again. If voltage is still out of spec, then replace the optic controller.
Voltage Checks Shown
End of Tubing
Volltage Check
Power
Supply Check
Power
Supply
Meter Reading
Status
Required Action
Voltage Within Specs at All three Checks
Wiring in Tubing, Power Supply OK, replace Bulb
Voltage out of spec at Power Source
Replace Power Supply
Voltage out of spec at Optic Controller (Stablizer)
Replace Optic Controller (Stablizer)
Voltage out of spec at tubing end.
Replace Tubing.
Models:
Serial Numbers:
All
All
TGC001000 thru TGC001024
V796868 thru V933242
© Midmark Corporation 2008 SF-1928
[Revised: dd/mo/yr]
B-26
Always verify model & serial number
Testing & Repair
Refer to:
Page
Access Procedures........C-1
Tubing Diagrams............D-1
Exploded Views ............E-1
Fiber Optic
(Current Production - Verify SN )
Testing
To check voltage...
A) Verify voltage at power supply connection to optic controller (stablizer) is 9 VDC.
B) With foot pedal depressed, check voltage on black and white wire connections at
optic controller (stablizer). Verify voltage is 2.9 - 4.1 VDC.
C) Remove instrument, swivel coupler (if equipped) and bulb (light module) from tubing.
D) Check voltage at wire connectors on tubing end. Verify voltage is 2.9 - 4.1 VDC.
Power Supply
Check
Optic
Controller
(Stablizer)
End of Tubing
Volltage Check
Voltage Checks Shown
Note
Power
Supply
Depress Foot
Control to
Check Wire Connection
Voltage
If the voltage is out of spec at the Optic Controller (Stablizer), check the air tubing
for air flow. If no air flow, check for a kink in the line. Repair and restore air flow, then
recheck voltage again. If voltage is still out of spec, then replace the optic controller.
Meter Reading
Models:
Status
Required Action
Voltage Within Specs at All three Checks
Wiring in Tubing, Power Supply OK, replace Bulb
Voltage out of spec at Power Source
Replace Power Supply
Voltage out of spec at Optic Controller (Stablizer)
Replace Optic Controller (Stablizer)
Voltage out of spec at tubing end.
Replace Tubing.
Only 8000-003, -004, -006, -006S,-007,-007S -008, -008S
Serial Numbers:
© Midmark Corporation 2008 SF-1928
V933243 thru Present
[Revised: 11/03/15
B-27
Always verify model & serial number
Testing & Repair
Refer to:
Handpiece Holder Adjustment
Earlier Production
Current Production
1/16” Allen
Wrench
Tubing Connector
1/16” Allen Wrench
To adjust handpiece holders..
A) Turn set screw on holder.
B) Place handpiece back in holder.
C) Verify handpiece shuts off. If not, adjust set screw again.
Note: If you loosen the earlier production style to far, the tubing connector will come out of holder. Put tubing connector back into slot and tighten set screw.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Page
Access Procedures........C-1
Tubing Diagrams............D-1
Exploded Views ............E-1
All
all
[Revised: 9/10/12]
B-28
Always verify model & serial number
Testing & Repair
Refer to:
Checking Foot Control
To check a foot controller that is leaking..
A) Check for hole or puncture in tubing.
B) Check springs, if compressed, stretch them out and reinstall.
C) Use soapy water to check o-rings for leaks.
D) Check tri-block diaphragm to see if it has a puncture. Tri-block is located behind the delivery panel, refer to Section C for access instructions.
Note: Also refer to: Checking for Leaks in Section B
Remove for Spring Access
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Page
Access Procedures........C-1
Tubing Diagrams............D-1
Exploded Views ............E-1
Remove for O-ring
Access
All
all
[Revised: 5/21/13]
B-29
Always verify model & serial number
Section C
© Midmark Corporation 2008 SF-1928
Access
Procedures
[Revised: 9/11/09]
Upper Compartment............................C-2
Middle Compartment...........................C-3
Lower Compartment............................C-3
Water System......................................C-5
Delivery System..................................C-6
Earlier Production Model Shown
C-1
Access Procedures
Upper Compartment
Caution
Power must be turned off when opening back door.
Step 1: Open door on back of cart to access upper compartment components.
Back Door
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Earlier Production Model Shown
All
all
[Revised: 09/11/09]
C-2
Always verify model & serial number
Access Procedures
Middle Compartment
Caution
Power must be turned off when removing panel.
Step 1: Unplug power cord from wall outlet and cart.
Step 2: Remove four screws to remove panel to access middle compartment.
VA1281
Earlier Production Models Only
Have a Middle Panel
Models:
Serial Numbers:
All
TGC001000 thru TGC001244
© Midmark Corporation 2008 SF-1928
[Revised: 09/11/09]
C-3
Always verify model & serial number
Access Procedures
Lower Compartment
Caution
Power must be turned off when removing panel.
Step 1: Remove six screws to remove panel to access lower compartment.
Current Models do not
have Receptacle
Earlier Production Models
Earlier Production Model Shown
VA1282
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 9/17/09]
C-4
Always verify model & serial number
Access Procedures
Water System
Step 1: Remove screws from top of water bottle bracket.
VA1283
Step 2: Remove water bottle from bracket.
Earlier Production Model Shown
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 5/22/13]
C-5
Always verify model & serial number
Access Procedures
Delivery Panel Access
Caution
Power must be turned off when removing panel.
Step 1: Remove two screws from top of panel.
Earlier Production Models
Current Production Models
VA1284
Step 2: Remove two screws from instrument holder panel.
Note: Push in on the foot control tubing to be able to pull out on the tubing
connected to back of the delivery panel.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 5/21/13]
C-6
Always verify model & serial number
Section D
© Midmark Corporation 2008 SF-1928
Wiring & Tubing
Diagrams
[Revised: dd/mo/yr]
D-1
Component/System
Page
Wiring Diagrams..................................D-2*
Tubing Diagrams.................................D-7*
Tri-Block..............................................D-12*
Quad-Block.........................................D-13
VetPro® 1000 Wire Diagram
Fiber Optics Detailed
VetPro® 1000
115 VAC
Satelec Scaler (Optional)
Components
Power Supply
Scaler
Control
Box
Receptacle for
Fiber Optic System
Fiber Optics
Components
(Optional)
VA1690
B
WHT
BLK
Adjustment
Knob
GRN
GRN
C
Transformer
BLK
K
BLK
GRN
BLK
Fan
G
L
BLK
BLK
BRN
BLK
BLK
BLK
WHT
WHT
Accessory
Receptacle
WHT
GRN
BLK
GRN
J
F
Pressure
Switch
BRN
Air
Switch
On/Off
Power Switch
WHT
GRN
Terminal Block
BLK
Circuit
Breaker
BLK
BLK
GRN
GRD
A
BRN
WHT
115 VAC
WHT
BRN
M
Compressor Head
D
Timer
GRN
Power Cord
Receptacle
GRN
E
J
Solenoid
I
GRD
GRN
BRN
BLU
Capacitor
H
Wiring Diagram
Item
Description
Part Number
A
Jumper Wire (Green-Yellow)
2 1/2”
015-0737-32
B
Jumper Wire (White) 23”
015-0737-34
C
Interior Receptacle
015-2555-00
D
Compressor Harness
015-2556-00
E
Exterior Receptacle
Connecting Harness
015-2557-00
F
Exterior Receptacle
Harness
015-2558-00
G
Jumper Wire (Black) 9”
015-0741-12
H
Jumper Wire (Black) 3 3/4”
015-0741-13
I
Jumper Wire (Black) 4”
015-0741-14
J
Jumper Wire (White) 5 1/4”
015-0741-15
K
Jumper Wire (Black)
015-0737-33
L
Fan Cord
015-2581-00
M
Jumper
015-0022-01
BLK
BLK
Assembled at Factory
Models:
Serial Numbers:
All
TGC001000Thru TGC001254
© Midmark Corporation 2008 SF-1928
[Revised: 9/22/11]
All
V796868 thru V933242
D-2
Always verify model & serial number
VetPro® 1000 Wire Diagram - 2
VetPro 1000™
115 VAC
Satelec Scaler (Optional)
Components
Fiber Optics
Components
(Optional)
Control
Box
Power Supply
Scaler
I
BLK
Receptacle for
Fiber Optic System
B
Adjustment
Knob
BLK
Fuse
BLK
BK
VA1691
J
BLK
BLK
Air
Switch
T0.8AL,250V,3AG
WH
GRN/YEL
M
BK
WHT
S
GND
Fan
BLU
G
H
WHT
Transformer
A
GRN/YEL
Pressure
Switch
BRN
On/Off
Power Switch
Q
BRN
Wiring Diagram
WHT
BLK
WHT
BLK
WHT
WHT
WHT
BLK
WHT
BLK
Circuit
Breakers
BL
BLK
O
Terminal
Block
L
GRN/YEL
Back Panel
E
F
BRN
BLK
BRN
C
K
Compressor Head
Timer
R
115 VAC
Power Cord
Receptacle
Solenoid
BRN
Note: Solenoid is
Normally Open
BRN
BRN
BLK
BLU
D
Models:
-007
Model Only
Fiber Optics Detailed
Capacitor
BLK
8000-001, -002, -003, -004, -007, -008
Serial Numbers:
© Midmark Corporation 2008 SF-1928
V933243 thru V1299689
[Revised: 7/16/12]
D-3
Item
N
P
A
Description
Part
Number
Transformer Input (White)
015-2713-00
B
Transformer Input (Black)
015-2712-00
C
Power Harness
015-2690-00
D
Compressor Harness
015-2689-00
E
Fan Cord
015-2581-00
F
Jumper Wire (Black) 9”
015-0741-12
G
Jumper Wire (Black) 2 1/2”
015-0737-44
H
Jumper Wire (Black) 6”
015-0737-43
I
Jumper Wire (White) 22”
015-0737-40
J
Jumper Wire (Black) 22”
015-0737-39
K
Jumper
015-0022-01
L
Jumper Wire (Green - Yellow) 6”
015-0708-35
M
Jumper Wire (Green - Yellow)
10”
015-0708-36
N
Jumper Wire (Black) 3 3/4”
015-0741-13
O
Jumper Wire (White) 3”
015-0741-16
P
Jumper Wire (Black) 5”
015-0741-17
Q
Jumper Wire (White) 5”
015-0741-18
R
Back Panel Inlet Harness
015-2677-00
S
Harness, Interior Receptacle
015-2688-00
Always verify model & serial number
VetPro® 1000 Wire Diagram - 3
VetPro 1000™
115 VAC
Satelec Scaler (Optional)
Components
Fiber Optics
Components
(Optional)
Control
Box
Power Supply
Scaler
I
BLK
Receptacle for
Fiber Optic System
B
Adjustment
Knob
BLK
Fuse
BLK
BK
VA1691
J
BLK
BLK
Air
Switch
T0.8AL,250V,3AG
WH
GRN/YEL
M
BK
WHT
S
GND
Fan
BLU
G
H
WHT
Transformer
A
GRN/YEL
Pressure
Switch
BRN
On/Off
Power Switch
Q
BRN
Wiring Diagram
WHT
BLK
WHT
BLK
WHT
BLK
WHT
WHT
WHT
BLK
Circuit
Breakers
BL
BLK
O
Terminal
Block
L
GRN/YEL
Back Panel
E
F
BRN
BLK
BRN
C
K
Compressor Head
Timer
R
115 VAC
Power Cord
Receptacle
Solenoid
BRN
Note: Solenoid is
Normally Open
BRN
BRN
BLK
BLU
D
Models:
-007
Model Only
Fiber Optics Detailed
Capacitor
BLK
8000-001, -002, -003, -004, -007, -008
Serial Numbers:
© Midmark Corporation 2008 SF-1928
V1299690 thru V1456588
[Revised: 8/28/13]
D-3.1
Item
N
P
A
Description
Part
Number
Transformer Input (White)
015-2713-00
B
Transformer Input (Black)
015-2712-00
C
Power Harness
015-2690-00
D
Compressor Harness
015-2689-00
E
Fan Cord
015-2581-00
F
Jumper Wire (Black) 9”
015-0741-12
G
Jumper Wire (Black) 2 1/2”
015-0737-44
H
Jumper Wire (Black) 6”
015-0737-43
I
Jumper Wire (White) 22”
015-0737-40
J
Jumper Wire (Black) 22”
015-0737-39
K
Jumper
015-0022-01
L
Jumper Wire (Green - Yellow) 6”
015-0708-35
M
Jumper Wire (Green - Yellow)
10”
015-0708-36
N
Jumper Wire (Black) 3 3/4”
015-0741-13
O
Jumper Wire (White) 3”
015-0741-16
P
Jumper Wire (Black) 5”
015-0741-17
Q
Jumper Wire (White) 5”
015-0741-18
R
Back Panel Inlet Harness
015-2677-00
S
Harness, Interior Receptacle
015-2688-00
Always verify model & serial number
VetPro® 1000 Wire Diagram - 4
VetPro 1000™
115 VAC
Satelec Scaler (Optional)
Components
Fiber Optics
Components
(Optional)
Control
Box
Power Supply
Scaler
I
BLK
Receptacle for
Fiber Optic System
B
Adjustment
Knob
BLK
Fuse
BLK
BK
VA1691
BLK
J
BLK
Air
Switch
T0.8AL,250V,3AG
WH
GRN/YEL
M
BK
WHT
S
GND
Fan
BLU
G
H
WHT
Transformer
A
BRN
On/Off
Power Switch
Q
BRN
WHT
BLK
WHT
O
BLK
Terminal
Block
BLK
WHT
WHT
WHT
WHT
Circuit
Breakers
BLK
BRN
C
K
Compressor Head
Timer
R
115 VAC
Power Cord
Receptacle
Solenoid
BRN
Note: Solenoid is
Normally Open
BRN
BRN
BLK
BLU
D
Serial Numbers:
Wiring Diagram
BLK
BL
BLK
L
Back Panel
E
F
BRN
GRN/YEL
GRN/YEL
Pressure
Switch
Models:
-007
Model Only
Fiber Optics Detailed
Capacitor
BLK
Item
N
P
Description
Part
Number
A
Transformer Input (White)
015-2713-00
B
Transformer Input (Black)
015-2712-00
C
Power Harness
015-2690-00
D
Compressor Harness
015-2689-00
E
Fan Cord
015-2581-00
F
Jumper Wire (Black) 9”
015-0741-12
G
Jumper Wire (Black) 2 1/2”
015-0737-44
H
Jumper Wire (Black) 6”
015-0737-43
I
Jumper Wire (White) 22”
015-0737-40
J
Jumper Wire (Black) 22”
015-0737-39
K
Jumper
015-0022-01
L
Jumper Wire (Green - Yellow) 12”
015-0708-35
M
Jumper Wire (Green - Yellow) 16”
015-0708-36
N
Jumper Wire (Black) 3 3/4”
015-0741-13
O
Jumper Wire (White) 3”
015-0741-16
P
Jumper Wire (Black) 5”
015-0741-17
015-0741-18
8000-001, -002, -003, -004, -007, -007S,-008, -008S
Q
Jumper Wire (White) 5”
V1456589 thru Present
R
Back Panel Inlet Harness
015-2677-00
S
Harness, Interior Receptacle
015-2688-00
© Midmark Corporation 2008 SF-1928
[Revised: 11/03/15]
D-3.2
Always verify model & serial number
VetPro® 1000 Wire Diagram - Export
VetPro 1000™
230 VAC
Fiber Optics Detailed
Satelec Scaler (Optional)
Components
Fiber Optics
Components
(Optional)
Power Supply
Scaler
Control
Box
VA1691-2
BLK
K
Receptacle for
Fiber Optic System
N
M
Adjustment
Knob
WHT
Transformer
BLK
S
J
Fuse
BLK
BLK
BLK
I
Air
Switch
T0.8AL,250V,3AG
BK
GRN/YEL
WH
BK
WHT
B
GND
Fan
BLU
Pressure
Switch
BRN
F
O
BRN
BRN
Back Panel
D
P
BLK
WHT
WHT
BLK
WHT
WHT
BLK
BLK
Terminal
Block
GRN/YEL
A
On/Off
Power Switch
WHT
WHT
BLK
Circuit
Breakers
BLK
BRN
H
R
Compressor Head
G
Timer
115 VAC
Power Cord
Receptacle
Solenoid
BRN
Note: Solenoid is
Normally Open
BRN
BRN
BLK
BLU
Capacitor
Q
Models:
Serial Numbers:
8000-005 & 8000-006
V1007096 thru V1299689
© Midmark Corporation 2008 SF-1928
[Revised: 7/16/12]
C
E
BL
L
GRN/YEL
D-4
Wiring Diagram
Item
Description
Part Number
A
Jumper Wire (GreenYellow) 6”
015-0708-35
B
Jumper Wire (GreeenYellow) 10”
015-0708-36
C
Jumper Wire (Black) 3
3/4”
015-0741-13
D
Jumper Wire (White) 3”
015-0741-16
E
Jumper Wire (Black) 5”
015-0741-17
015-0741-18
F
Jumper Wire (White) 5”
G
Back Panel Inlet Harness
015-2677-00
H
Jumper
015-0022-01
I
Jumper Wire (Black) 22”
015-0737-39
J
Jumper Wire (White) 22”
015-0737-40
K
Jumper Wire (Black) 10”
015-0737-41
L
Jumper Wire (White) 10”
015-0737-42
M
Jumper Wire (Black) 6”
015-0737-43
015-0737-44
N
Jumper Wire (Black) 2
1/2”
O
Jumper Wire (Black) 9”
015-0741-12
P
Fan Cord
015-2581-00
Q
Compressor Harness
015-2689-00
R
Power Harness
015-2690-00
S
Harness, Interior Receptacle, Export
015-2719-00
Always verify model & serial number
VetPro® 1000 Wire Diagram - Export - 2
VetPro 1000™
230 VAC
Fiber Optics Detailed
Satelec Scaler (Optional)
Components
Fiber Optics
Components
(Optional)
Power Supply
Scaler
Control
Box
VA1691-2
BLK
K
Receptacle for
Fiber Optic System
N
M
Adjustment
Knob
WHT
Transformer
BLK
S
J
Fuse
BLK
BLK
BLK
I
Air
Switch
T0.8AL,250V,3AG
BK
GRN/YEL
WH
BK
WHT
B
GND
Fan
BLU
Pressure
Switch
BRN
F
O
BRN
BRN
Back Panel
D
P
BLK
WHT
WHT
BLK
WHT
WHT
BLK
BLK
Terminal
Block
GRN/YEL
A
On/Off
Power Switch
WHT
WHT
BLK
Circuit
Breakers
BL
L
GRN/YEL
BLK
BRN
H
R
Compressor Head
G
Timer
115 VAC
Power Cord
Receptacle
Solenoid
BRN
Note: Solenoid is
Normally Open
BRN
BRN
BLK
BLU
Capacitor
Q
Models:
Serial Numbers:
8000-005 & 8000-006
V1299690 thru V14565898
© Midmark Corporation 2008 SF-1928
[Revised: 8/28/13]
D-4.1
C
E
Wiring Diagram
Item
Description
Part Number
A
Jumper Wire (GreenYellow) 6”
015-0708-35
B
Jumper Wire (GreeenYellow) 10”
015-0708-36
C
Jumper Wire (Black) 3
3/4”
015-0741-13
D
Jumper Wire (White) 3”
015-0741-16
E
Jumper Wire (Black) 5”
015-0741-17
015-0741-18
F
Jumper Wire (White) 5”
G
Back Panel Inlet Harness
015-2677-00
H
Jumper
015-0022-01
I
Jumper Wire (Black) 22”
015-0737-39
J
Jumper Wire (White) 22”
015-0737-40
K
Jumper Wire (Black) 10”
015-0737-41
L
Jumper Wire (White) 10”
015-0737-42
M
Jumper Wire (Black) 6”
015-0737-43
015-0737-44
N
Jumper Wire (Black) 2
1/2”
O
Jumper Wire (Black) 9”
015-0741-12
P
Fan Cord
015-2581-00
Q
Compressor Harness
015-2689-00
R
Power Harness
015-2690-00
S
Harness, Interior Receptacle, Export
015-2719-00
Always verify model & serial number
VetPro® 1000 Wire Diagram - Export - 3
VetPro 1000™
230 VAC
Fiber Optics Detailed
Satelec Scaler (Optional)
Components
Fiber Optics
Components
(Optional)
Power Supply
Scaler
Control
Box
VA1691-2
BLK
K
Receptacle for
Fiber Optic System
N
M
Adjustment
Knob
WHT
Transformer
BLK
S
J
Fuse
BLK
BLK
BLK
I
Air
Switch
T0.8AL,250V,3AG
BK
GRN/YEL
WH
BK
WHT
B
GRN/YEL
GND
Fan
BLU
Pressure
Switch
BRN
F
O
BRN
BRN
Back Panel
D
P
BLK
WHT
WHT
BLK
Circuit
Breakers
WHT
BLK
WHT
WHT
BLK
BLK
Terminal
Block
A
On/Off
Power Switch
WHT
BL
L
GRN/YEL
BLK
BRN
H
R
Compressor Head
G
Timer
115 VAC
Power Cord
Receptacle
Solenoid
BRN
Note: Solenoid is
Normally Open
BRN
BRN
BLK
BLU
Capacitor
Q
Models:
8000-005, 8000-006 & 8000-006S
Serial Numbers:
© Midmark Corporation 2008 SF-1928
V1456589 thru Present
[Revised: 11/4/15]
D-4.2
C
E
Wiring Diagram
Item
Description
Part Number
A
Jumper Wire (GreenYellow) 12”
015-0708-35
B
Jumper Wire (GreenYellow) 16”
015-0708-36
C
Jumper Wire (Black) 3
3/4”
015-0741-13
D
Jumper Wire (White) 3”
015-0741-16
E
Jumper Wire (Black) 5”
015-0741-17
015-0741-18
F
Jumper Wire (White) 5”
G
Back Panel Inlet Harness
015-2677-00
H
Jumper
015-0022-01
I
Jumper Wire (Black) 22”
015-0737-39
J
Jumper Wire (White) 22”
015-0737-40
K
Jumper Wire (Black) 10”
015-0737-41
L
Jumper Wire (White) 10”
015-0737-42
M
Jumper Wire (Black) 6”
015-0737-43
015-0737-44
N
Jumper Wire (Black) 2
1/2”
O
Jumper Wire (Black) 9”
015-0741-12
P
Fan Cord
015-2581-00
Q
Compressor Harness
015-2689-00
R
Power Harness
015-2690-00
S
Harness, Interior Receptacle, Export
015-2719-00
Always verify model & serial number
VetPro® 1000 Terminal Block Connections
Pressure Switch (Black)
Inside Receptacle (Black)
Transformer (Top - Black)
Compressor (White)
Transformer (Bottom - Black)
Inside Receptacle (White)
Compressor (Green)
Inside Receptacle (Green)
Ground
Natural
Line
Back Receptacle (Green)
Cart Box Frame (Green)
Back Receptacle (White)
Fan (Black)
Fan (Black)
Back Receptacle (Black)
Models:
Serial Numbers:
All
All
TGC001000Thru TGC001254
V796868 thru V933242
© Midmark Corporation 2008 SF-1928
[Revised: 8/9/10]
D-5
Always verify model & serial number
VetPro® 1000 Terminal Block Connections - 2
Pressure Switch (Black)
Inside Receptacle (Brown)
Transformer (Top - Black)
Compressor (White)
Transformer (Bottom - White)
Inside Receptacle (Blue)
Ground
Natural
Line
Circuit Breaker (White)
Fan (Black)
Fan (Black)
Circuite Breaker (Black)
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
V933243 thru Present
[Revised: 8/9/10]
D-5.1
Always verify model & serial number
VetPro® 1000 Tubing Diagram
8000-001
Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
The drive air adjustment screws are located on front of Tri-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement is needed use 1/4” yellow
tubing listed in Section E of this manual.
1/4" Gray
1/8" Clear
1/4" Blue
1/8"
Gray
1/4" Gray
1/8"
Blue
1/8"
Blue
Push
to
Open
1/4" Gray
1/4"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8"
Blue
1/4"
Gray
1/8" Blue
1/4" Gray
1/8" Blue
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/8" Clear
3/8" Blue
1/8" Clear
Push
to
Open
1/8" Clear
1/8" Red
1/8" Orange
1/4" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Orange
1/4" Gray
1/16" I.D. Gray
Syringe Tube
1/8" Green
1/8" Orange
1/8" Red
1/4" Gray
1/8" Clear
1/4" Clear
Push
to
Open
1/8" Blue
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Clear
1/8"
Clear
1/8" Blue
1/8" Clear
Syringe
(Typical
Location)
1/8" Clear
1/8" Red
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
Handpiece Holders
1/8" Blue
Models:
Serial Numbers:
1/8" Blue
1/8"
Gray
1/8" Blue
VA1244
8000-001
TGC001000 thru TGC001024
© Midmark Corporation 2008 SF-1928
[Revised: 05/24/2011
D-6
Always verify model & serial number
VetPro® 1000 Tubing Diagram
8000-001
Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
The drive air adjustment screws are located on front of Tri-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement is needed use 1/4” yellow
tubing listed in Section E of this manual.
1/4" Gray
1/8" Clear
1/4" Blue
1/8"
Gray
1/4" Gray
1/8"
Blue
1/8"
Blue
Handpiece
Valve (N.C.)
3-Way
Push
to
Open
1/4" Gray
1/4"
Gray
1/8"
Blue
1/4"
Gray
1/8" Blue
1/4" Gray
1/8" Blue
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/8" Clear
3/8" Blue
1/8" Clear
Push
to
Open
1/8" Clear
1/8" Orange
Handpiece
Valve (N.C.)
3-Way
1/8" Green
1/4" Clear
1/8" Orange
1/4" Gray
1/16" I.D. Gray
Syringe Tube
1/8" Green
1/8" Green
1/8" Orange
1/4" Gray
1/8" Clear
1/4" Clear
Push
to
Open
1/8" Blue
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Clear
1/8"
Clear
1/8" Blue
1/8" Clear
Syringe
(Typical
Location)
1/8" Clear
1/8" Red
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
Handpiece Holders
1/8" Blue
Models:
Serial Numbers:
1/8" Blue
1/8"
Gray
1/8" Blue
VA1244-1
8000-001
TGC001025 thru TGC001244
© Midmark Corporation 2008 SF-1928
[Revised: 05/24/2011
D-6.1
Always verify model & serial number
VetPro® 1000 Tubing Diagram
8000-001 & 8000-005
Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
The drive air adjustment screws are located on front of Tri-Block.
1/4" Yellow
1/8" Clear
1/4" Blue
1/8"
Blue
1/4"
Yellow
1/8"
Blue
Push
to
Open
1/4" Yellow
1/4"
Yellow
1/4"
Yellow
1/8"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8" Blue
1/4" Yellow
1/8" Blue
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/4" Yellow
3/8" Blue
1/8" Clear
Push
to
Open
1/8" Clear
1/8" Orange
1/8" Green
1/4" Clear
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Orange
1/4" Yellow
1/16" I.D. Gray
Syringe Tube
1/8" Green
1/8"
Blue
1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/4" Clear
Push
to
Open
1/8" Blue
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Clear
1/8"
Clear
1/8" Blue
1/8" Clear
Syringe
(Typical
Location)
1/8" Clear
1/8" Red
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
Handpiece Holders
1/8" Blue
1/8" Blue
1/8"
Gray
1/8" Blue
VA1244-2
Models:
Serial Numbers:
8000-001 & 8000-005
V796868 thru V1043397
© Midmark Corporation 2008 SF-1928
[Revised: 5/24/2011]
D-6.2
Always verify model & serial number
VetPro® 1000 Tubing Diagram
8000-001 & 8000-005
Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
The drive air adjustment screws are located on front of Tri-Block.
1/4" Yellow
1/8" Clear
1/4" Blue
1/8"
Blue
1/4"
Yellow
1/8"
Blue
Push
to
Open
1/4" Yellow
1/4"
Yellow
1/4"
Yellow
1/8"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8" Blue
1/4" Yellow
1/8" Blue
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/4" Yellow
3/8" Blue
1/8" Clear
Push
to
Open
1/8" Clear
1/8" Orange
1/8" Green
1/4" Clear
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Orange
1/4" Yellow
1/16" I.D. Gray
Syringe Tube
1/8" Green
1/8"
Blue
1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/4" Clear
Push
to
Open
1/8" Blue
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Clear
1/8"
Clear
1/8" Blue
1/8" Clear
Syringe
(Typical
Location)
1/8" Clear
1/8" Red
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
Handpiece Holders
1/8" Blue
1/8" Blue
1/8"
Gray
1/8" Blue
VA1244-3
Models:
8000-001 & 8000-005
Serial Numbers:
© Midmark Corporation 2008 SF-1928
V1043398 thru Present
[Revised: 5/24/2011]
D-6.3
Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-002
Note
Rear view tubing connections are shown on Dual-Block and Mainfolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement
is needed use 1/4” yellow tubing listed in Section E of this manual.
1/4" Gray
1/8" Clear
1/8"
Gray
1/4" Blue
1/4" Gray
1/8"
Blue
1/8"
Blue
Push
to
Open
1/4" Gray
1/4"
Gray
Push
to
Open
1/8" Clear
1/8" Clear
1/8" Blue
1/4" Gray
1/8" Blue
1/8" Clear
1/16" I.D. Gray
Syringe Tube
3/8" Blue
1/8" Red
1/8" Orange
1/8"
Blue
1/4"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8" Blue
1/8"
Gray
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/4" Clear
1/4" Gray
1/8" Orange
1/8" Orange
1/8" Green
1/8" Red
1/4" Gray
1/8" Clear
Syringe
(Typical
Location)
1/4" Clear
1/8" Clear
1/8" Clear
1/8" Blue
Handpiece Holders
1/8" Clear
1/8" Blue
1/8" Blue
1/8"
Gray
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
VA1258
1/8" Blue
Models:
Serial Numbers:
8000-002
TGC001000 thru TGC001024
© Midmark Corporation 2008 SF-1928
[Revised: 5/24/2011]
D-7
Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-002
Note
Rear view tubing connections are shown on Dual-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement
is needed use 1/4” yellow tubing listed in Section E of this manual.
1/4" Gray
1/8" Clear
1/8"
Gray
1/4" Blue
1/4" Gray
1/8"
Blue
1/8"
Blue
Push
to
Open
1/4" Gray
1/4"
Gray
Push
to
Open
1/8" Clear
1/8" Clear
1/8" Blue
1/4" Gray
1/8" Blue
1/8" Clear
1/16" I.D. Gray
Syringe Tube
3/8" Blue
1/8" Orange
1/8" Green
1/8"
Blue
1/4"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8" Blue
1/8"
Gray
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/4" Clear
1/4" Gray
1/8" Orange
1/8" Green
1/8" Green
1/8" Orange
1/4" Gray
1/8" Clear
Syringe
(Typical
Location)
1/4" Clear
1/8" Clear
1/8" Clear
1/8" Blue
Handpiece Holders
1/8" Clear
1/8" Blue
1/8" Blue
1/8"
Gray
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
VA1258-1
1/8" Blue
Models:
Serial Numbers:
8000-002
TGC001025 thru TGC001244
© Midmark Corporation 2008 SF-1928
[Revised: 5/24/2011]
D-7.1
Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-002
Note
Rear view tubing connections are shown on Dual-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.
1/4" Yellow
1/8" Clear
1/4" Yellow
1/8"
Gray
1/4" Blue
1/4"
Yellow
Handpiece
Valve (N.C.)
3-Way
1/8"
Blue
1/8"
Blue
Push
to
Open
1/4" Yellow
1/8"
Blue
1/8" Blue
1/4" Yellow
1/8" Blue
1/4"
Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube
3/8" Blue
Push
to
Open
1/8" Clear
1/8" Clear
1/8" Orange
1/8" Green
1/4" Clear
1/8" Blue
1/8"
Gray
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/4" Yellow
1/8" Orange
1/8" Green
1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
Syringe
(Typical
Location)
1/4" Clear
1/8" Clear
1/8" Clear
1/8" Blue
Handpiece Holders
1/8" Clear
1/8" Blue
1/8" Blue
1/8"
Gray
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
VA1258-2
1/8" Blue
Models:
Serial Numbers:
8000-002
V796868 thru V1043397
© Midmark Corporation 2008 SF-1928
[Revised: 4/25/2011]
D-7.2
Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-002
Note
Rear view tubing connections are shown on Dual-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.
1/4" Yellow
1/8" Clear
1/4" Yellow
1/8"
Gray
1/4" Blue
1/4"
Yellow
Handpiece
Valve (N.C.)
3-Way
1/8"
Blue
1/8"
Blue
1/8"
Blue
Push
to
Open
1/4" Yellow
1/8" Blue
1/4" Yellow
1/8" Blue
1/4"
Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
3/8" Blue
Push
to
Open
1/8" Clear
1/8" Clear
1/8" Orange
1/8" Green
1/4" Clear
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/4" Yellow
1/8" Orange
1/8" Green
1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
Syringe
(Typical
Location)
1/4" Clear
1/8" Clear
1/8" Clear
1/8" Blue
Handpiece Holders
1/8" Clear
1/8" Blue
1/8" Blue
1/8"
Gray
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
VA1258-3
1/8" Blue
Models:
Serial Numbers:
8000-002
V1043398 thru Present
© Midmark Corporation 2008 SF-1928
[Revised: 4/25/11]
D-7.3
Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-003
Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
The drive air adjustment screws are located on front of Tri-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement is
needed use 1/4” yellow tubing listed in Section E of this manual.
1/8" Clear
1/4"
Gray
1/4" Blue
1/8"
Blue
1/8"
Blue
Push
to
Open
1/4" Gray
1/4"
Gray
1/8"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8"
Blue
1/8" Blue
1/8" Red
1/8" Blue
1/4" Gray
1/4"
Gray
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/8" Blue
1/4" Gray
3/8" Blue
1/8" Clear
Push
to
Open
1/8" Clear
1/8" Orange
1/8" Green
1/4" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Orange
1/4" Gray
1/16" I.D. Gray
Syringe Tube
1/8" Green
1/8" Clear
1/8" Green
1/8" Orange
1/4" Gray
1/8" Clear
1/4" Clear
Push
to
Open
1/8" Blue
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Clear
1/8"
Clear
1/8" Blue
1/8" Clear
Syringe
(Typical
Location)
1/8" Clear
1/8" Red
1/8" Blue
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
Handpiece Holders
1/8" Blue
Models:
Serial Numbers:
1/8"
Gray
1/8" Blue
VA1372
8000-003
TGC001000 Thru TGC001244
© Midmark Corporation 2008 SF-1928
[Revised: 5/24/2011]
D-8
Always verify model & serial number
VetPro® 1000 Tubing Diagram
8000-003 & 8000-006 & 8000-008
Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
The drive air adjustment screws are located on front of Tri-Block.
1/4" Yellow
1/8" Clear
1/4"
Yellow
1/4" Blue
1/8"
Blue
1/8"
Blue
Push
to
Open
1/4" Yellow
1/4"
Yellow
1/8"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8"
Blue
1/8" Blue
1/8" Red
1/8" Blue
1/4" Yellow
1/4"
Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/4" Yellow
3/8" Blue
1/8" Clear
Push
to
Open
1/8" Clear
1/8" Orange
1/8" Green
1/4" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Orange
1/4" Yellow
1/16" I.D. Gray
Syringe Tube
1/8" Green
1/8" Clear
1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/4" Clear
Push
to
Open
1/8" Blue
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Clear
1/8"
Clear
1/8" Blue
1/8" Clear
Syringe
(Typical
Location)
1/8" Clear
1/8" Red
1/8" Blue
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
Handpiece Holders
1/8" Blue
1/8"
Gray
1/8" Blue
VA1372-2
Models: 8000-003 & 8000-006 & 8000-008
Serial Numbers:
© Midmark Corporation 2008 SF-1928
V796868 thru V1043397
[Revised: 6/20/12]
D-8.1
Always verify model & serial number
VetPro® 1000 Tubing Diagram
8000-003 & 8000-006 & 8000-008
Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
The drive air adjustment screws are located on front of Tri-Block.
1/4" Yellow
1/8" Clear
1/4"
Yellow
1/4" Blue
1/8"
Blue
1/4"
Yellow
1/8"
Blue
Push
to
Open
1/4" Yellow
1/8"
Blue
1/8"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8" Blue
1/8" Red
1/8" Blue
1/4" Yellow
1/4"
Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/4" Yellow
3/8" Blue
1/8" Clear
Push
to
Open
1/8" Clear
1/8" Orange
1/8" Green
1/4" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Orange
1/4" Yellow
1/16" I.D. Gray
Syringe Tube
1/8" Green
1/8" Clear
1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/4" Clear
Push
to
Open
1/8" Blue
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Clear
1/8"
Clear
1/8" Blue
1/8" Clear
Syringe
(Typical
Location)
1/8" Clear
1/8" Red
1/8" Blue
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
Handpiece Holders
1/8" Blue
1/8"
Gray
1/8" Blue
VA1372-3
Models: 8000-003 & 8000-006 & 8000-008
Serial Numbers:
© Midmark Corporation 2008 SF-1928
V1043398 thru V1271515
[Revised: 8/7/12]
D-8.2
Always verify model & serial number
VetPro® 1000 Tubing Diagram
8000-003 & 8000-006 & 8000-008
Note
Rear view tubing connections are shown on Tri-Block and Manifolds for clarity.
The drive air adjustment screws are located on front of Tri-Block.
1/4" Yellow
1/8" Clear
1/4"
Yellow
1/4" Blue
1/8"
Blue
1/4"
Yellow
1/8"
Blue
Push
to
Open
1/4" Yellow
1/8"
Blue
1/8"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8" Blue
1/8" Red
1/8" Blue
1/4" Yellow
1/4"
Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/4" Yellow
3/8" Blue
1/8" Clear
Push
to
Open
1/8" Clear
1/8" Orange
1/8" Green
1/4" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Orange
1/4" Yellow
1/16" I.D. Gray
Syringe Tube
1/8" Green
1/8" Clear
1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/4" Clear
Push
to
Open
1/8" Blue
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Clear
1/8"
Clear
1/8" Blue
1/8" Clear
Syringe
(Typical
Location)
1/8" Clear
1/8" Red
1/8" Blue
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
Handpiece Holders
1/8" Blue
1/8"
Gray
1/8" Blue
VA1372-4
Models:
8000-003, 8000-006, 8000-006S, 8000-008 & 8000-008S
Serial Numbers:
© Midmark Corporation 2008 SF-1928
V1271516 thru Present
[Revised: 11/7/15]
D-8.3
Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-004
Note
Rear view tubing connections are shown on Dual-Block and Manifolds for clarity. The drive
air adjustment screws are located on front of Dual-Block.
Units built under SN sequence below have 1/4” grey tubing, if replacement is needed use
1/4” yellow tubing listed in Section E of this manual.
1/4" Gray
1/8" Clear
1/8"
Gray
1/4" Gray
1/8"
Blue
1/8"
Blue
Push
to
Open
1/4" Gray
1/4"
Gray
1/4"
Gray
1/8"
Blue
Handpiece
Valve (N.C.)
3-Way
1/8" Blue
1/8" Red
1/8" Blue
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/4" Gray
3/8" Blue
Push
to
Open
1/8" Clear
1/8" Clear
1/8" Orange
1/8" Green
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/4" Clear
1/4" Gray
1/8" Orange
1/8" Green
1/8" Green
1/8" Orange
1/4" Gray
1/8" Clear
Syringe
(Typical
Location)
1/4" Clear
1/8" Clear
1/8" Clear
1/8" Blue
Handpiece Holders
1/8" Clear
1/8" Blue
1/8" Blue
1/8"
Gray
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
VA1373
1/8" Blue
Models:
Serial Numbers:
8000-004
TGC001000 Thru TGC001244
© Midmark Corporation 2008 SF-1928
[Revised: 5/24/11]
D-9
Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-004
Note
Rear view tubing connections are shown on Dual-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.
1/4" Yellow
1/8" Clear
1/8"
Blue
1/8"
Gray
1/4"
Yellow
1/4" Blue
1/4"
Yellow
1/8"
Blue
Push
to
Open
1/4" Yellow
1/4"
Yellow
1/8"
Blue
Handpiece
Valve (N.C.)
3-Way
1/8" Blue
1/8" Red
1/8" Blue
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/4"
Yellow
3/8" Blue
Push
to
Open
1/8" Clear
1/8" Clear
1/8" Orange
1/8" Green
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/4" Clear
1/4" Yellow
1/8" Orange
1/8" Green
1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
Syringe
(Typical
Location)
1/4" Clear
1/8" Clear
1/8" Clear
1/8" Blue
Handpiece Holders
1/8" Clear
1/8" Blue
1/8" Blue
1/8"
Gray
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
VA1373-1
1/8" Blue
Models:
Serial Numbers:
8000-004
V796868 thru V1043397
© Midmark Corporation 2008 SF-1928
[Revised: 4/25/11]
D-9.1
Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-004
Note
Rear view tubing connections are shown on Dual-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Dual-Block.
1/4" Yellow
1/8" Clear
1/4"
Yellow
1/4"
Yellow
1/4" Blue
1/8"
Blue
1/8"
Blue
Push
to
Open
1/4" Yellow
1/4"
Yellow
1/8"
Blue
1/8"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8" Blue
1/8" Red
1/8" Blue
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/4"
Yellow
3/8" Blue
Push
to
Open
1/8" Clear
1/8" Clear
1/8" Orange
1/8" Green
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/4" Clear
1/4" Yellow
1/8" Orange
1/8" Green
1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
Syringe
(Typical
Location)
1/4" Clear
1/8" Clear
1/8" Clear
1/8" Blue
Handpiece Holders
1/8" Clear
1/8" Blue
1/8" Blue
1/8"
Gray
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
VA1373-2
1/8" Blue
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
8000-004
V1043398 thru Present
[Revised: 4/25/11]
D-9.2
Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-007
Note
Rear view tubing connections are shown on Quad-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Quad-Block.
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/4"
Yellow
1/8"
Gray
Push
to
Open
1/8"
Blue
1/8" Blue
1/8" Red
1/4" Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/4"
Yellow
1/4" Blue
1/8"
Blue
1/8"
Blue
Push
to
Open
1/4" Yellow
1/4"
Yellow
1/8"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8"
Blue
1/8" Blue
1/8" Red
1/8" Blue
1/4" Yellow
1/4"
Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/4" Yellow
3/8" Blue
1/8" Clear
Push
to
Open
1/8" Clear
1/8" Orange
1/8" Green
1/4" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Orange
1/4" Yellow
1/16" I.D. Gray
Syringe Tube
1/8" Green
1/8" Clear
1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/4" Clear
Push
to
Open
1/8" Blue
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Clear
1/8"
Clear
1/8" Blue
1/8" Clear
Syringe
(Typical
Location)
1/8" Clear
1/8" Red
1/8" Blue
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
Handpiece Holders
1/8" Blue
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
1/8"
Gray
1/8" Blue
VA1638
8000-007
V933243 thru V1043397
[Revised: 6/20/12]
D-10
Always verify model & serial number
VetPro® 1000 Tubing Diagram 8000-007
Note
Rear view tubing connections are shown on Quad-Block and Manifolds for
clarity. The drive air adjustment screws are located on front of Quad-Block.
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/4"
Yellow
1/8"
Gray
Push
to
Open
1/8"
Blue
1/8" Blue
1/8" Red
1/4" Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/4"
Yellow
1/4" Blue
1/8"
Blue
1/8"
Blue
Push
to
Open
1/4" Yellow
1/4"
Yellow
1/8"
Blue
1/8"
Gray
Handpiece
Valve (N.C.)
3-Way
1/8" Blue
1/8" Red
1/8" Blue
1/4" Yellow
1/4"
Yellow
1/8" Clear
1/16" I.D. Gray
Syringe Tube
1/8" Blue
1/8"
Gray
1/4" Yellow
3/8" Blue
1/8" Clear
Push
to
Open
1/8" Clear
1/8" Orange
1/8" Green
1/4" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Orange
1/4" Yellow
1/16" I.D. Gray
Syringe Tube
1/8" Green
1/8" Clear
1/8" Green
1/8" Orange
1/4" Yellow
1/8" Clear
1/4" Clear
Push
to
Open
1/8" Blue
1/8" Clear
Handpiece
Valve (N.C.)
3-Way
1/8" Clear
1/8"
Clear
1/8" Blue
1/8" Clear
Syringe
(Typical
Location)
1/8" Clear
1/8" Red
1/8" Blue
1/8" Blue
1/8" Blue
1/8" Clear
1/8"
Blue
Handpiece Holders
1/8" Blue
Models:
© Midmark Corporation 2008 SF-1928
1/8" Blue
VA1638-1
8000-007 & 8000-007S
Serial Numbers:
1/8"
Gray
V1043398 thru Present
[Revised: 6/20/12]
D-10.1
Always verify model & serial number
Tri-Block
Rear View
Handpiece Coolant Water
Handpiece Coolant Air
Coolant Water
Coolant Air
Holder Handpiece
(Typical 3 Places)
Drive Air
Pressure Gauge
Handpiece Drive Air
Note
Rear view tubing connections are shown on Tri-Block for clarity.
Connections are the same for Dual Block minus one handpiece.
Isometric Rear View
Models:
Serial Numbers:
All
TGC001000 thru TGC001024
© Midmark Corporation 2008 SF-1928
[Revised: 8/28/08]
D-11
Always verify model & serial number
Tri-Block
Rear View
Handpiece Coolant Water
Handpiece Coolant Air
Coolant Water
Coolant Air
Holder Handpiece
(Typical 3 Places)
Drive Air
Pressure Gauge
Handpiece Drive Air
Note
Isometric Rear View
Models:
Serial Numbers:
Rear view tubing connections are shown on Tri-Block for clarity.
Connections are the same for Dual Block minus one handpiece.
SN beginning with TGC have large grey tubing.
SN beginning with V have large Yellow tubing.
All
TGC001025 Thru TGC001244
© Midmark Corporation 2008 SF-1928
[Revised: 1/19/2010]
D-11.1
Always verify model & serial number
Tri-Block
Rear View
Handpiece Coolant Water
Handpiece Coolant Air
Coolant Water
Coolant Air
Holder Handpiece
(Typical 3 Places)
Drive Air
Pressure Gauge
Handpiece Drive Air
Note
Isometric Rear View
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Rear view tubing connections are shown on Tri-Block for clarity.
Connections are the same for Dual Block minus one handpiece.
SN beginning with TGC have large grey tubing.
SN beginning with V have large Yellow tubing.
All
V796868 thru Present
[Revised: 6/16/10]
D-11.2
Always verify model & serial number
Quad-Block
Rear View
Handpiece Coolant Water
Handpiece Coolant Air
Coolant Water
Coolant Air
Holder Handpiece
(Typical 4 Places)
Drive Air
Pressure Gauge
Handpiece Drive Air
Isometric Rear View
Note
Rear view tubing connections are
shown on Quad-Block for clarity.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
8000-007 & 8000-007S
V933243 thru Present
[Revised: 11/7/15]
D-12
Always verify model & serial number
Section E
© Midmark Corporation 2008 SF-1928
Exploded Views &
Parts Lists
[Revised: dd/mo/yr]
XXX-XXXX-XX
XXX-XXXX-XX
XXX-XXXX-XX
E-1
Vet Pro 1000.......................................E2
VetPro® 1000
Panel Components...... E-8*
Fiber Optic Components ........................E-15*
Fiber Optic Electrical Components.........E-18*
Upper Compartment.... E-5*
Delivery....................... E-6*
Water System.............. E-7*
Middle Compartment... E-4*
Lower Compartment.... E-3*
Earlier Production Model Shown
Frame and Back Components............E-9*
Athena Handpieces and Maintenance............E-12
Athena Replacement Components ................E-17
Midmark Brand Handpieces and Parts ..........E-13
Foot Control Assembly ........E-11
Tubing & Fittings.......... E-10*
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
Handpiece Holders...... E-17
All
* Indicates multiple pages due to a serial
number break for the parts illustration.
all
[Revised: 11/21/11]
Syringe........................ E-14
Scaler.......................... E-15
E-2
Always verify model & serial number
1
a) 015-2390-00
b) 002-1145-00
21
015-2394-00
2014-0182-00
3014-0660-00
4
20
015-2395-00
041-0006-02
016-1195-00
2
19
002-1143-00
17
041-0250-13
16
23
6014-0023-01
Lower Compartment Components
Description
1
7014-0645-00
15
8014-0648-00
961901406
040-0250-79 14
10
a) 002-1148-00
b) 014-0694-00
Qty.
a) Replacement Compressor Head (includes
capacitor)
b) Head Rebuild Kit (refer to ”Installation: (Compressor Head Rebuild Kit” [642648A-0605] in
Repair Kits folder for Installation Instructions)
1
2
Hex Nipple (1/4” NPT)
3
3
ST Elbow (1/4” NPT)
1
4
a) Filter Element Only
b) Muffler, Plastic, Assembly
1
5
Elbow Union (1/4” NPT)
1
6
Hex Bushing (3/8” MPT x 1/4” FPT)
1
7
Check Valve
1
8
Barb Fitting (1/2” x 3/8” MPT)
1
9
Allen Plug (1/8” MPT)
1
10
Solenoid (Includes Item #9)
a) Domestic
b) Export
1
11
Compressor Plate
1
12
Pan Head Screw (6/32” x 1/2”)
1
13
Screw (0.138-32 X 0.375)
2
14
Hex Head Screw (1/4 20” x 1/2”)
1
15
Vibration Mount
4
16
Hex Nut (1/2 13”)
4
17
Screw (0.250-20 X 0.625)
1
18
Bubble Mount
4
19
Kep Nut (6/32”)
8
All
20
Strap Loop
2
21
Capacitor
1
TGC001000 Thru TGC001254
22
Nipple
1
23
Muffler, Bronze
1
040-0006-108
13
VA1286
11050-7581-00-232
12
Models:
Serial Numbers:
a) 002-1149-00
b) 10589100
5014-0218-03
22
014-0045-00
18
040-0250-79
016-1194-00
© Midmark Corporation 2008 SF-1928
[Revised: 4/5/16]
040-0006-27
E-3
Always verify model & serial number
1
a) 015-2390-00
b) 015-2668-00
c) 002-1145-00
2014-0317-02
040-0008-79
3014-0194-01
20
a) 015-2394-00
b) 015-2676-00
015-2395-00
21
4
19
014-0023-01
041-0006-0218
Item
5014-0218-03
002-1143-0023
016-1195-00 17
040-0250-79
Lower Compartment Components
6
22
014-0045-00
a) 002-1149-00
b) 10589100
16
7014-0645-00
041-0250-1315
8014-0648-00
016-1194-0014
961901406
040-0250-7913
040-0006-108
Models:
Serial Numbers:
12
10
a) 002-1148-00
b) 014-0694-00
11050-7581-00-232
All
V796868 thru V1299689
© Midmark Corporation 2008 SF-1925
[Revised: 4/5/16]
E-3.1
VA1286-1
Description
Qty.
1
a) Compressor Head, Dom. (includes capacitor)
b) Compressor Head, Export (includes capacitor)
c) Head Rebuild Kit (refer to ”Installation: (Compressor Head Rebuild Kit” [642648A-0605] in
Repair Kits folder for Installation Instruction.)
1
2
Hex Nipple (1/4” NPT)
3
3
ST Elbow (1/4” NPT)
1
4
a) Filter Element Only
b) Plastic Muffler Assembly
1
5
Elbow Union (1/4” NPT)
1
6
Hex Bushing (3/8” MPT x 1/4” FPT)
1
7
Check Valve
1
8
Barb Fitting (1/2” x 3/8” MPT)
1
9
Allen Plug (1/8” MPT)
1
10
Solenoid (Includes Item #9)
a) Domestic
b) Export
1
11
Compressor Plate
1
12
Screw (0.138-32 X 0.375)
2
13
Hex Head Screw (1/4 20” x 1/2”)
1
14
Vibration Mount
4
15
Hex Nut (1/2 13”)
4
16
Screw (0.250-20 X 0.625)
1
17
Bubble Mount
1
18
Kep Nut (6/32”)
8
19
Strap Loop
2
20
Capacitor
a) Domestic Models
b) Export Models (-005 & -006)
1
21
Pan Head Screw (6/32” x 1/2”)
2
22
Nipple
1
23
Muffler, Bronze
1
Always verify model & serial number
1
040-0008-79
2014-0317-02
22
3014-0194-01
21
a) 015-2394-00
b) 015-2676-00
4
Lower Compartment Components
041-0006-0219
014-0023-01
016-1195-00 18
6
Item
23
014-0045-00
22
040-0250-79
a) 002-1149-00
b) 10589100
20
015-2395-00
62970706
a) 015-2390-00
b) 015-2668-00
c) 002-1145-00
5014-0218-03
002-1143-0024
17
16
7014-0645-00
041-0250-1315
8014-0648-00
016-1194-0014
961901406
040-0250-7913
10
040-0006-108
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1925
12
a) 002-1148-00
b) 014-0694-00
11050-7581-00-232
All
V1299690 thru Present
[Revised: 4/5/16]
E-3.2
VA1286-2
Description
Qty.
1
a) Compressor Head, Dom. (includes capacitor)
b) Compressor Head, Export (includes capacitor)
c) Head Rebuild Kit (refer to ”Installation: (Compressor Head Rebuild Kit” [642648A-0605] in
Repair Kits folder for Installation Instruction.)
1
2
Hex Nipple (1/4” NPT)
3
3
ST Elbow (1/4” NPT)
1
4
a) Filter Element Only
b) Plastic Muffler Assembly
1
5
Elbow Union (1/4” NPT)
1
6
Hex Bushing (3/8” MPT x 1/4” FPT)
1
7
Check Valve
1
8
Barb Fitting (1/2” x 3/8” MPT)
1
9
Allen Plug (1/8” MPT)
1
10
Solenoid (Includes Item #9)
a) Domestic
b) Export
1
11
Compressor Plate
1
12
Screw (0.138-32 X 0.375)
2
13
Hex Head Screw (1/4 20” x 1/2”)
1
14
Vibration Mount
4
15
Hex Nut (1/2 13”)
4
16
Screw (0.250-20 X 0.625)
1
17
3-Pole Terminal Block
1
18
Bubble Mount
1
19
Kep Nut (6/32”)
8
20
Strap Loop
2
21
Capacitor
a) Domestic Models
b) Export Models (-005 & -006)
1
22
Pan Head Screw (8/32” x 1/2”)
6
23
Nipple
1
24
Muffler, Bronze
1
Always verify model & serial number
041-0008-04
050-7602-00-232
014-0689-00
17
16
1040-0010-144
15
015-2398-00 14
2015-2397-00
62970707 13
18002-1574-00
041-0006-02 12
015-2399-00
12
1
11
1057240010
Middle Compartment Components
Item
015-2191-01
9
2
Transformer (Scaler Models Only)
1
3
Screw
4
4
Circuit Breaker
1
5
Receptacle, Double
1
6
AC Connector Receptacle
1
7
Screw (6/32” x 1/2”)
3
8
Switch, Rocker
1
9
Pan Head Screw (6/32 X.375)
1
10
Fan, 115 VAC (115V Models only)
1
11
Timer, Interval
1
12
Kep Nut (6/32”)
20
13
Terminal Block
1
14
Pressure Switch
1
All
15
90° Elbow, 1/4" Compression x 1/4" NPT
1
16
Bracket
1
TGC001000 Thru TGC001254
17
Kep Nut (8/32”)
12
19
Power Cord
1
3040-0006-105
9
8
4015-2400-00
4
040-0006-27
Models:
Serial Numbers:
Qty.
Pan Head Screw (10/32 x 1/2”)
1
040-0006-108
Description
1
VA1292
© Midmark Corporation 2008 SF-1928
[Revised: 11/3/2015]
7
015-2403-00
6
5
015-0083-02
E-4
Always verify model & serial number
050-7602-00-232
014-0689-00
040-0006-27
3015-2397-00
11
015-2399-00
10572400
2040-0010-47
14
12
62970707
002-1574-00
15
13
015-2398-00
16
1040-0008-79
2
10
9
4015-0083-02
040-0006-108
8
015-2191-01
5015-2400-00
7
5
6
015-0639-01
VA1292-1
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1925
All
V796868 thru V933242
[Revised: 11/3/2015]
E-4.1
Middle Compartment Components
Item
Description
Qty.
1
Pan Head Screw .164-32 x .500
4
2
Pan Head Screw 10-24 X 3/8
8
3
Transformer (Scaler Models Only)
1
4
Receptacle, Double
1
5
Circuit Breaker
1
6
AC Connector Receptacle
1
7
Rocker Switch
1
8
Pan Head Screw 6-32X.375 BO
1
9
Fan, 115 VAC (115V Models only)
1
10
Timer, Interval
1
11
Pan Head Screw 6-32 x 1/2”
2
12
Terminal Block
1
13
Pressure Switch
1
14
90° Elbow, 1/4" Compression x 1/4" NPT
1
15
Bracket
1
16
Power Cord
1
Always verify model & serial number
1040-0008-79
050-7602-00-232
15
14
014-0689-00
2015-2703-00
015-2398-00 13
62970707
16
3015-1534-00
1
12
1
a) 002-1574-00
b) 015-0363-00
015-2399-00
462502416
11
5015-0346-48
6040-0010-129
10
a) 10572400
b) 015-2667-00
Middle Compartment Components
Item
015-2714-00
9
Circuit Breaker
a) 015-2711-00
b) 015-2711-01
8
015-0639-01
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1925
7
Overload %
Trip Times
100 %
No Trip
135 %
1 Hour
200 %
400 %
600 %
800 %
1000 %
2.2 - 15 sec
0.55 - 1.8 sec
0.27 - 0.7 sec
0.17 - 0.45 sec
0.12 - 0.3 sec
All
V933243 thru Present
[Revised: 11/3/2015]
E-4.2
VA1292-2
Description
Qty.
1
Pan Head Screw .164-32 x .500
12
2
Transformer (Scaler Models Only)
1
3
Fuseblock (1/4” x 1 1/4”)
1
4
Screw (Pan Head .138-32 x .500)
1
5
Fuse, 3 AG, Slo-Blo, 800mA, 250V
1
6
Screw (10-24 x 1/2” Pan Head Phillips)
4
7
AC Connector Receptacle
1
8
Circuit Breaker
a) Domestic (6 amp.)
b) Export (3 amp.)
2
9
Rocker Switch
1
10
Fan
a) Domestic
b) Export
1
11
Timer, Interval
1
12
Terminal Block
1
13
Pressure Switch
1
14
90° Elbow, 1/4" Compression x 1/4" NPT
1
15
Bracket
1
16
Power Cord
a) Domestic
b) Export Models (-005 & -006)
1
Always verify model & serial number
040-0312-41
19
1014-0651-01
2014-0652-00
3014-0698-00
15
014-0656-00
014-0655-00
12
18
002-1987-00
4014-0176-55
1
17
16
002-1144-00
Upper Compartment Components
15
122841
Item
14
13
121533
041-0008-04
12
015-0083-01
014-0653-00
11
015-2586-00
10
040-0006-27
Models:
Serial Numbers:
014-0619-00
8
7
9
VA1294
TGC001000 thru TGC001254
[Revised: 6/24/2015]
5014-0194-01
6014-0182-02
All
© Midmark Corporation 2008 SF-1928
5
E-5
Description
Qty.
1
Air Tank Container (Lid and tank)
1
2
Adapter (1” MPT x 1/4” FPT)
2
3
Fitting, Compression Stem (1/4 MPT X 1/4
4
O-ring
1
5
Elbow St (1/4” NPT)
1
6
Nipple (1/4” MPT x 3”)
1
7
Shut-Off Valve (1/4” NPT)
1
8
Tube Connector (1/4” x 1/4” MPT)
1
9
• Items 8-12 Only In Models with Fiber Optics
Screw (6/32” x 1/2”)
1
10
Receptacle Cover - Duplex
1
11
Receptacle - Duplex
1
12
Nut (8/32”)
4
13
Electrical - Duplex
1
14
Pressure Gauge (1/8” NPT)
1
15
Replacement Filter
16
Tee Union
3
17
Stem Adapter (1/4” x 1/8”)
1
18
Regulator Kit
1
19
Cap Screw (5/16-18” x 1”)
4
20
Not Shown - 015-0371-01
Drain Valve Hose Clip
1
Always verify model & serial number
040-0312-41
19
1014-0651-01
2014-0652-00
3014-0698-00
15
014-0656-00
014-0655-00
12
18
002-1987-00
4014-0176-55
1
17
16
002-1144-00
15
122841
Upper Compartment Components
Item
14
121533
13
77009189
12
015-0083-01
014-0653-00
11
015-2586-00
10
040-0006-27
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1925
014-0619-00
8
7
5014-0194-01
6014-0182-02
9
VA1294-1
All
V796868 thru V933242
[Revised: 6/24/2015]
5
E-5.1
Description
Qty.
1
Air Tank Container (Lid and tank)
1
2
Adapter (1” MPT x 1/4” FPT)
2
3
Fitting, Compression Stem (1/4 MPT X 1/4
4
O-ring
1
5
Elbow St (1/4” NPT)
1
6
Nipple (1/4” MPT x 3”)
1
7
Shut-Off Valve (1/4” NPT)
1
8
Tube Connector (1/4” x 1/4” MPT)
1
9
• Items 8-12 Only In Models with Fiber Optics
Screw (6/32” x 1/2”)
1
10
Receptacle Cover - Duplex
1
11
Receptacle - Duplex
1
12
Nut (8/32”)
4
13
Electrical - Duplex
1
14
Pressure Gauge (1/8” NPT)
1
15
Replacement Filter
16
Tee Union
3
17
Stem Adapter (1/4” x 1/8”)
1
18
Regulator Kit
1
19
Cap Screw (5/16-18” x 1”)
4
20
Not Shown - 015-0371-01
Drain Valve Hose Clip
1
Always verify model & serial number
016-1219-00
3
4
014-0698-00
014-0344-00
040-0250-133
1
2
5
014-0655-00
21
014-0348-00
6
7
014-0653-00
014-0619-00
5
014-0656-00
8
014-0182-02
002-1144-00
9
12
13
VA1294-2
014-0194-01
10
002-1987-00
122841
Serial Numbers:
© Midmark Corporation 2008 SF-1925
Item
Description
Qty.
1
Hex Head Plug (1/4” NPT Brass)
1
2
Hex Head Whiz Lock (1/4”-20 x 1/2”)
3
3
Pressure Tank, One GAL
1
4
Adapter Stem (1/4” MPT x 1/4”)
1
5
Tee Union
2
6
Barb Fitting (3/8” )
1
7
Connector (1/4”MPT x 1/4” TB)
1
8
Shut off Valve (1/4” NPT)
1
9
Pipe Nipple (1/4” MPT x 3”)
1
10
90 degree Elbow (1/4” x 1/4”)
1
11
Regulator Kit
1
All
12
Adapter Stem (1/8” MPT x 1/4”)
2
13
Regulator Filter Element Kit
V933243 thru Present
14
Pressure Gauge (1/8” NPT, 0-130 PSI)
15
Refer to: Fiber Optic Electrical Components
11
Models:
14
Upper Compartment Components
15
[Revised: 6/24/2015]
E-5.2
Always verify model & serial number
1
a) 029-4651-00
b) 029-4651-02
18
050-7615-00-23219
1122582
041-0006-02 20
2117585
4029-2449-03
3
5
3
a) 050-7612-00-232
b) 050-7613-00-232
6053-1165-01
7014-0666-00
029-4652-00 17
8040-0006-53
AR = as required
Delivery System Components
Item
9040-0006-27
20
VA1298
050-7614-00-232
a) 029-4650-00 15
b) 029-4657-00
10
12
9
a) 029-4655-00
b) 029-4656-00
c) 002-1146-00
Qty.
Loop Strap
2
Water Relay
1
3
Refer to: Tubing & Fittings
AR
4
Air Control Valve
AR
5
a) Delivery Control Panel - with Scaler
b) Delivery Control Panel - without Scaler
6
Knob, blue (includes set screw)
7
Gauge with Bracket
8
Pan Head Screw (6/32” x 1/4”)
AR
9
Pan Head Screw (6/32” x 1/2”)
2
10
a) Syringe Holder
b) Universal Holder
c) Pilot Valve - Handpiece - Repair
1
1
AR
1
AR
11
Bar Holder
1
12
Bracket
1
13
Bracket (Block)
1
14
Pan Head Screw (4-40x 1/4”)
2
15
a) Tri-Block (Models 8000-001 & 8000-003)
b) Dual-Block (Models 8000-002 & 8000-004)
1
16
Not Shown - 002-1147-00
Tri-Block Replacement Membrane Repair Kit
1
All
17
Manifold Assembly (Syringe)
18
Manifold Assembly a) Handpiece b) Scaler
TGC001000 Thru TGC001254
19
Delivery Back Box
20
Kep Nut (6/32”)
040-0004-00
14
051-1203-00-232
11
050-7616-00-23213
Models:
Serial Numbers:
Description
1
© Midmark Corporation 2008 SF-1928
[Revised: 10/26/15]
E-6
Always verify model & serial number
1
AR
1
AR
Valve
Air Control Valve
Assembly includes:
22
Lock
Washer
Trim
Nut
040-0010-129
040-0004-00
050-7873-00-232
21
20
1
029-2449-03
a) 050-7872-00-232
b) 050-7871-00-232
053-1165-01
014-0666-00
19
2041-0006-02
18
15
17
3050-7616-00-232
AR = as required
Delivery System Components
15
Item
4
16
1
a) 029-4651-01
b) 029-4651-00
c) 029-4651-02
d) 029-4652-00
5050-7874-00-232
10040-0010-47
6040-0006-108
040-0008-06
12040-0010-74
14
029-4994-00
16
13
P12575
11
7
8117585
9122582
Models:
Serial Numbers:
a) 029-4650-00
b) 029-4657-00
All
V796868 thru V933242
© Midmark Corporation 2008 SF-1925
[Revised 10/23/15]
E-6.1
Description
a) Tri-Block (Models 8000-001 & 8000-003)
b) Dual-Block (Models 8000-002 & 8000-004)
Qty.
1
2
Nut #6-32 KEPS W/Starwasher
3
Bracket (Tri-Block)
4
Handpiece blocks (Facing Front - Left to Right)
a) Fiber Optic (Models 8000-003 & 800-004)
b) Manifold Assy, Handpiece
c) Manifold Assy. Scaler
d) Mainfold, Syringe
5
Block Bracket
6
Screw Pan Head (6-32X.375)
7
Refer to: Tubing & Fittings
8
Valve, C.W. Control
1
9
Clamp (11/16”)
1
10
Screw (#10-24 x 3/8”)
2
11
Lock Washer
2
12
Screw Pan Head PHL (10-32 x 3/8”)
2
13
Handpiece Holder Assembly, Four Position
1
14
Screw Mach, Pan Head PHL (8-32 x 1/2)
4
15
Gauge, Panel Mount, 0-100 PSI
16
Refer to: Handpiece Holders
17
Knob , Blue (Includes set Screw)
3
18
a) Control Panel without Scaler
b) Control Panel with Scaler
1
19
Air Control Valve
3
20
Screw, Pan Head
2
21
Screw Pan Head, TT ZCBC (.190-24 x .500)
4
22
Control Panel Box
1
23
Not Shown - 002-1147-00
Tri-Block Replacement Membrane Repair Kit
1
Always verify model & serial number
AR
1
1 EA
1
2
AR
1
AR
Valve
Air Control Valve
Assembly includes:
050-7873-00-232
Lock
Washer
Trim
Nut
040-0010-129
a) 050-7872-00-232
b) 050-8002-00-232
c) 050-8001-00-232
053-1165-01
122841
18
029-2449-03
19
21
23
053-2163-00
040-0004-00
22
1
20
2041-0006-02
AR = as required
15
Delivery System Components
Item
17
15
3050-7616-00-232
4
16
a) 029-5122-01
b) 029-5122-00
c) 029-5122-02
d) 029-4652-00
5050-7874-00-232
2
6040-0006-108
040-0008-06
10
14
a) 029-4994-00 13
b) 029-4994-01
16
040-0010-47
7
12040-0010-74
11
8117585
P12575
9122582
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1925
All
V933243 thru V986004
[Revised: 10/26/15]
a) 029-4650-00
b) 029-4993-00
c) 029-5119-00
E-6.2
Description
Qty.
1
a) Tri-Block (Models 8000-001 & 8000-003)
b) Dual-Block (Models 8000-002 & 8000-004)
c) Quad-Block (Model 8000-007)
2
Nut #6-32 KEPS W/Starwasher
3
Bracket (Tri-Block)
4
Handpiece blocks (Facing Front - Left to Right)
a) Fiber Optic (Models 8000-003 & 800-004)
(For 8000-007 ONLY 2 required)
b) Manifold Assy, Handpiece
c) Manifold Assy. Scaler
d) Mainfold, Syringe
5
Block Bracket
6
Screw Pan Head (6-32X.375)
7
Refer to: Tubing & Fittings
8
Valve, C.W. Control
1
9
Clamp (11/16”)
1
10
Screw (#10-24 x 3/8”)
2
11
Lock Washer
2
12
Screw Pan Head PHL (10-32 x 3/8”)
2
13
Handpiece Holder Assembly a) Four Position b) Five Position
1
14
Screw Mach, Pan Head PHL (8-32 x 1/2)
4
15
Gauge, Panel Mount, 0-100 PSI
16
Refer to: Handpiece Holders
17
Knob , Blue (Includes set Screw)
3
18
a) Control Panel without Scaler
b) Control Panel with Scaler
c) Control Panel, five position
1
19
Air Control Valve
3
20
Screw, Pan Head
2
21
Screw Pan Head, TT ZCBC (.190-24 x .500)
4
22
Control Panel Box
1
23
Insulator for Scaler (Tightens on with qty 2 of
item # 2)
1
24
Not Shown - 002-1147-00
Tri-Block Replacement Membrane Repair Kit
1
Always verify model & serial number
1
AR
1
1 EA
1
2
AR
1
AR
Valve
Air Control Valve
Assembly includes:
050-7873-00-232
Lock
Washer
Trim
Nut
040-0010-129
a) 050-7872-00-232
b) 050-8002-00-232
c) 050-8001-00-232
053-1165-01
122841
18
029-2449-03
19
21
23
053-2163-00
040-0004-00
22
1
20
2041-0006-02
AR = as required
15
Delivery System Components
Item
17
15
3050-7616-00-232
4
16
a) 029-5122-01
b) 029-5122-00
c) 029-5122-02
d) 029-4652-00
5050-7874-00-232
2
6040-0006-108
040-0008-06
10
14
a) 029-4994-00
b) 029-4994-01
13
16
040-0010-47
7
12040-0010-74
11
8117585
P12575
9122582
Models:
Serial Numbers:
All
V986005 thru V1043397
© Midmark Corporation 2008 SF-1925
[Revised: 10/26/15]
a) 029-4650-00
b) 029-4993-00
c) 029-5119-00
E-6.3
Description
Qty
1
a) Tri-Block (Models 8000-001, -003, -005, -006 & -008)
b) Dual-Block (Models 8000-002 & -004)
c) Quad-Block (Model 8000-007)
1
2
Nut #6-32 KEPS W/Starwasher
5
3
Bracket (Tri-Block)
1
4
Handpiece blocks (Facing Front - Left to Right)
a) Fiber Optic (Models 8000-003,-004, -006 & -008)
(For 8000-007 ONLY 2 required)
b) Manifold Assy, Handpiece
c) Manifold Assy. Scaler
d) Mainfold, Syringe
5
Block Bracket
6
Screw Pan Head (6-32X.375)
7
Refer to: Tubing & Fittings
8
Valve, C.W. Control
1
9
Clamp (11/16”)
1
10
Screw (#10-24 x 3/8”)
2
11
Lock Washer
2
12
Screw Pan Head PHL (10-32 x 3/8”)
2
13
Handpiece Holder Assembly a) Four Position b) Five Position
1
14
Screw Mach, Pan Head PHL (8-32 x 1/2)
4
15
Gauge, Panel Mount, 0-100 PSI
16
Refer to: Handpiece Holders
17
Knob , Blue (Includes set Screw)
3
18
a) Control Panel without Scaler
b) Control Panel with Scaler
c) Control Panel, five position
1
19
Air Control Valve
3
20
Screw, Pan Head
2
21
Screw Pan Head, TT ZCBC (.190-24 x .500)
4
22
Control Panel Box
1
23
Insulator for Scaler (Tightens on with qty 2 of item # 2)
1
24
Not Shown - 002-1147-00
Tri-Block Replacement Membrane Repair Kit
1
Always verify model & serial number
1 EA
1
8
AR
1
AR
Valve
Air Control Valve
Assembly includes:
050-7873-00-232
Lock
Washer
Trim
Nut
040-0010-129
053-2163-00
a) 050-7872-00-232
b) 050-8002-00-232
c) 050-8001-00-232
21
029-2449-03
24
1
27
Delivery System Components
Item
22
2
Nut #6-32 KEPS W/Starwasher
3
Bracket
4
Handpiece blocks (Facing Front - Left to Right)
a) Fiber Optic (Models 8000-003 & 800-004)
(For 8000-007 ONLY 2 required)
b) Manifold Assy, Handpiece
c) Manifold Assy. Scaler
d) Mainfold, Syringe
5
Block Bracket
6
Screw Pan Head (6-32X.375)
7
Refer to: Tubing & Fittings
8
Valve, C.W. Control
1
9
Clamp (11/16”)
1
10
Gauze Sponge
2
11
Exhaust Collector Top Housing
1
12
Exhaust Collector Bottom Housing
1
13
Screw (10-24 x 1/2” Pan Head Phillips)
2
14
Lock Washer
2
15
Screw Pan Head PHL (10-32 x 3/8”)
2
16
Handpiece Holder Assembly a) Four Position b) Five Position
1
17
Screw Mach, Pan Head PHL (8-32 x 1/2)
4
18
Gauge, Panel Mount, 0-100 PSI
19
Refer to: Handpiece Holders
20
Knob , Blue (Includes set Screw)
3
21
a) Control Panel without Scaler
b) Control Panel with Scaler
c) Control Panel, five position
1
22
Air Control Valve
3
23
Screw, Pan Head
2
24
Screw Pan Head, TT ZCBC (.190-24 x .500)
4
25
Control Panel Box
1
All
26
Insulator for Scaler (Tightens on with qty 2 of
item # 2)
2
V1043398 thru Present
24
Not Shown - 002-1147-00
Tri-Block Replacement Membrane Repair Kit
1
2041-0006-02
4
19
a) 029-5122-01
b) 029-5122-00
c) 029-5122-02
d) 029-4652-00
5050-8282-00-216
17
16
P12575
6040-0006-108
14
2
19
7
121547
040-0010-74
040-0010-129
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1925
Qty.
1
3050-7616-00-232
a) 029-4994-00
b) 029-4994-01
Description
a) Tri-Block (Models 8000-001 & 8000-003)
b) Dual-Block (Models 8000-002 & 8000-004)
c) Quad-Block (Model 8000-007)
18
040-0008-06
a) 029-4650-00
b) 029-4993-00
c) 029-5119-00
AR = as required
23
20
053-1165-01
014-0666-00
040-0004-00
25
[Revised: 10/26/15]
15
13
10
053-1614-00-216
8117585
11
053-1615-00-216
12
9122582
E-6.4
Always verify model & serial number
1
AR
1
1 EA
1
8
AR
1
AR
1040-0010-144
4
4
029-4651-00 10
2050-8078-00-232
3040-0006-105
4014-0667-00
6
9
4
5053-2040-00
11053-2041-00
6
6
6
7053-1828-00
Water System Components
Item
VA1297
014-0668-00
9
Pan Head Screw (10/32” x 1/2”)
2
Water Bottle Bracket
3
Pan Head Screw (6/32” x 1”)
Qty.
4
1
AR
4
Water Regulator Assembly
5
Water Bottle Cap
6
Refer to: Tubing & Fittings
7
Water Bottle (1 Liter)
2
All
8
Valve Rounting Toggle
1
9
Nipple (10/32”)
2
TGC001000Thru TGC001254
10
Hex Plug (10/32”)
11
Water Bottle Gasket
014-0669-00
Models:
Serial Numbers:
Description
1
© Midmark Corporation 2008 SF-1928
[Revised: 4/20/12]
8
E-7
Always verify model & serial number
1
2
AR
2
AR
1041-0006-02
2040-0008-06
5
3050-7621-00-232
4040-0006-109
016-0888-00 15
5002-1366-00
13
13
7117481
14
6153284
8117482
1
14
109714
14
Item
16
014-0176-52
11053-1828-00
9
12002-1367-00
117660
13
177524
10
VA129701i
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1925
All
V796868 thru Present
[Revised: 2/6/2012]
Water System Components
E-7.1
Description
Qty.
1
Nut (#6/32)
4
2
Pan Head Screw (8/32” x 1/2”)
4
3
Water Bottle Bracket
4
Pan Head Screw (6/32” x 1”)
5
Water Regulator Assembly Kit
*Also includes item # 13, 14 & 16
1
6
Water Bottle Cap Assembly (incl. 7 thru 10)
2
7
Barb Fitting (1/16” to 1/16”)
2
8
Barb Fitting (1/8” x 1/8”)
2
9
Water Bottle Gasket
2
10
Pick-Up Tube
2
11
Water Bottle (1 Liter)
2
12
Valve Rounting Toggle Kit (w/ relief)
*Also includes item # 13, 14 & 15
1
13
Gasket (3/16” x 5/16” x 1/32”)
5
14
Barb Fitting (10/32” x 1/16”)
5
15
90° Swivel Fitting (#10/32)
2
Always verify model & serial number
1
AR
116599
053-2054-00-216
15
1
14
1040-0010-144
016-0945-03
13
2053-2056-00-216
1
050-7582-00-23212
1
3053-2053-00-216
Panel Components
054-0597-00
Item
Description
Qty.
1
Pan Head Screw (10/32” x 1/2”)
AR
2
Right Side Panel
1
3
Front Panel
1
4
Caster
2
5
Pan Head Screw (6/32” x 1/2”)
4
6
Screen Cover Kit (includes item 5)
1
7
Locking Caster
2
8
Lock Washer (1/2”-13)
4
9
Nut (1/2”-13)
4
10
Left Panel
1
11
Foam, Electrical Compartment
1
All
12
Removable Panel, Electrical Enclosure
1
13
Edge Trim (order by inch - qty 1 = 1”)
AR
TGC001000 thru TGC001254
14
Top Panel
1
15
Stainless Steel Tray
1
11
053-2055-00-21610
1
4016-1193-00
VA1301
041-0500-00 9
045-0001-33 8
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
[Revised: 1/24/11]
016-1197-00 7
002-1228-00 6
E-8
5
040-0006-27
Always verify model & serial number
14
116599
053-2054-00-216
1
13
1040-0010-129
054-0597-00
12
2053-2056-00-216
1
050-7861-00-232
11
1
3053-2053-00-216
053-2055-00-21610
VA1301-1
1
Item
4016-1193-00
041-0500-00 9
016-1197-00 7
045-0001-33 8
040-0008-79 5
002-1228-00 6
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1925
All
V796868 thru V1097496
[Revised: 8/10/2011]
Panel Components
E-8.1
Description
Qty.
1
Pan Head Screw (10/32” x 1/2”)
AR
2
Right Side Panel
1
3
Front Panel
1
4
Caster
2
5
Pan Head Screw (6/32” x 1/2”)
4
6
Screen Cover Kit (includes item 5)
1
7
Locking Caster
2
8
Lock Washer (1/2”-13)
4
9
Nut (1/2”-13)
4
10
Left Panel
1
11
Removable Panel, Electrical Enclosure
1
12
Foam, Electrical Compartment
1
13
Top Panel
1
14
Stainless Steel Tray
1
Always verify model & serial number
14
116599
053-2054-00-216
1
13
1040-0010-129
054-0597-00
12
2053-2056-00-216
1
050-7861-00-232
11
1
3053-2053-00-216
053-2055-00-216 10
VA1301-1
1
041-0500-00
045-0001-33
Item
4016-1422-00
9
016-1423-00
8
7
002-1228-00
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1925
040-0008-79
6
All
V1097497 thru Present
[Revised: 3/13/12]
Panel Components
E-8.2
5
Description
Qty.
1
Pan Head Screw (10/32” x 1/2”)
AR
2
Right Side Panel
1
3
Front Panel
1
4
Caster
2
5
Pan Head Screw (6/32” x 1/2”)
4
6
Screen Cover Kit (includes item 5)
1
7
Locking Caster
2
8
Lock Washer (1/2”-13)
4
9
Nut (1/2”-13)
4
10
Left Panel
1
11
Removable Panel, Electrical Enclosure
1
12
Foam, Electrical Compartment
1
13
Top Panel
1
14
Stainless Steel Tray
1
Always verify model & serial number
15
137258
16053-2052-00
a) 053-2051-01
b) 053-2051-00
17050-7632-00-232
14
040-0010-154
21
13
12
19
23
040-0008-06
24
041-0010-14
11
1042-0081-08
10
Frame and Back Components
Item
5
9
002-1285-00
050-7634-00-232
040-0010-144
8
7
050-7635-00-232
6
77009189
a) 054-0592-00
b) 054-0593-00
c) 054-0594-00
d) 054-0595-00
5
4
VA1273
030-1821-00-232
2
053-0068-15 3
Models:
Serial Numbers:
015-0371-00
040-0010-74
7
050-7636-00-232
040-0010-146
22002-1297-00
18016-0447-01
051-1217-00-232 13
040-0010-144
20
All
TGC00100 Thru TGC001254
© Midmark Corporation 2008 SF-1928
[Revised: 6/16/10]
E-9
Description
Qty.
1
Bolt (1 1/4” x 1/4”)
2
2
Frame
1
3
Snap Bushing (1/2” Dia)
4
4
Installation
a) Front & Back Side Mounts (1 EA)
b) Left & Right Side Mounts (2 EA)
c) Upper Mount (1 EA)
d) Lower Mount (1EA)
5
Kep Nut (10/32”)
6
6
Compressor Cover
1
7
Pan Head Screw (10/32”)
2
8
Electrical Cover
1
9
Back Door Kit
Includes items #18, #19, #5, and #10
1
10
Screw, Panhead (8-32X1/2)
3
11
Bracket
1
12
Screw (.190 x 32 x 1/2”)
2
13
Back Handle
1
14
Quick Disconnect Assembly
2
15
a) Red Washer
b) Blue Washer
16
QD spacer
2
17
Panel, Top back Cover
1
18
Knob
1
19
Pan Head Screw (10/32” x 3/8”)
1
20
Screw (.190 x 32 x .437)
2
21
Screw (.190 x 32 x .75)
1
22
Magnet Kit.
1
23
Cable Clamp
1
24
Magnet kit
1
25
Not Shown - 015-1338-02
Power Supply Cord
1
Always verify model & serial number
AR
1 EA
052-0707-00-232
053-2208-00
1040-0008-01
19
14
18
2137258
3
4040-0008-43
a) 053-2051-01
b) 053-2051-00
5002-1297-00
14
050-7636-00-232 17
6015-0371-00
10
777009189
040-0008-0616
030-1827-00-232 15
8030-1885-00-232
040-0010-129
14
050-7863-00-232 13
Frame and Back Components
Item
050-7858-00-232 12
Coupling, FEM QD
1
3
Screw, Flat Head (8-32 x 3/4”)
3
5
Flat Mounting Magnet (M4 X .7)
1
6
Drain Valve Hose Clip
1
7
Nut (M4)
1
8
Frame, Weldment for Dental Cart
1
9
Insulation
a) Front & Back Side Mounts (1 EA)
b) Left & Right Side Mounts (2 EA)
c) Upper Mount (1 EA)
d) Lower Mount (1EA)
10
Locknut (8-32)
9
11
Screw, Panhead (#10-24 X 3/8”)
6
12
Electrical Cover Panel
1
13
Panel, Top Back Cover
1
14
Screw, Panhead (.190” x 1/2”)
10
15
Back Door Weldment
1
All
16
Screw, Panhead (#8-32 x 1/2”)
3
17
Cord Bracket
1
V796868 thru V871908
18
Door Handle
1
19
Handle
1
10
VA1273-2
a) 054-0592-00
b) 054-0593-00
c) 054-0594-00
d) 054-0595-00
© Midmark Corporation 2008 SF-1925
2
2
4
77009189
Serial Numbers:
Qty.
Screw, Panhead ( 0.164 X 0.75)
a) Red Washer
b) Blue Washer
040-0010-47 11
Models:
Description
1
[Revised: 11/10/10]
9
E-9.1
Always verify model & serial number
1 EA
AR
052-0707-00-23218
053-2208-00
17
13
1040-0008-01
2137258
13
3
a) 053-2051-01
b) 053-2051-00
4
050-7863-00-232
5016-1313-00
050-7636-00-232 16
10
6015-0371-00
2
040-0008-0615
7041-0026-04
030-1827-00-232 14
040-0010-129
050-7858-00-232
8030-1885-00-232
13
12
Frame and Back Components
Item
040-0010-47
11
Coupling, FEM QD
1
3
Panel, Top Back Cover
1
5
Flat Mounting Magnet (M4 X .7)
1
6
Drain Valve Hose Clip
1
7
Nut (M4)
1
8
Frame, Weldment for Dental Cart
1
9
Insulation
a) Front & Back Side Mounts (1 EA)
b) Left & Right Side Mounts (2 EA)
c) Upper Mount (1 EA)
d) Lower Mount (1EA)
10
Locknut (8-32)
6
11
Screw, Panhead (#10-24 X 3/8”)
6
12
Electrical Cover Panel
1
13
Screw, Panhead (.190” x 1/2”)
10
14
Back Door Weldment
1
All
15
Screw, Panhead (#8-32 x 1/2”)
3
16
Cord Bracket
1
V871909 thru V933242
17
Door Handle
1
18
Handle
1
a) 054-0592-00
b) 054-0593-00
c) 054-0594-00
d) 054-0595-00
© Midmark Corporation 2008 SF-1925
2
2
4
10
VA1273-4
Serial Numbers:
Qty.
Screw, Panhead ( 0.164 X 0.75)
a) Red Washer
b) Blue Washe
77009189
Models:
Description
1
[Revised: 11/10/10]
9
E-9.2
Always verify model & serial number
1 EA
AR
052-0707-00-23218
053-2208-00
12
17
1040-0008-01
3
2137258
a) 053-2051-01
b) 053-2051-00
4016-1313-00
14
050-7636-00-232 16
2
5041-0026-04
6030-1885-00-232
15
015-0371-00
8
040-0008-0614
030-1827-00-232 13
Frame and Back Components
12
040-0010-129
Item
2
Coupling, FEM QD
3
a) Red Washer
b) Blue Washe
4
Flat Mounting Magnet (M4 X .7)
1
5
Nut (M4)
1
6
Frame, Weldment for Dental Cart
1
7
Insulation
a) Front & Back Side Mounts (1 EA)
b) Left & Right Side Mounts (2 EA)
c) Upper Mount (1 EA)
d) Lower Mount (1EA)
8
Locknut (8-32)
5
9
Screw (10-24 x 1/2” Pan Head Phillips)
6
10
Electrical Cover Panel
1
11
Panel, Top Back Cover
1
12
Screw, Panhead (.190” x 1/2”)
10
13
Back Door Weldment
1
14
Screw, Panhead (#8-32 x 1/2”)
5
All
15
Tubing Clamp
2
16
Cord Bracket
1
V933243 thru Present
17
Door Handle
1
18
Handle
1
15
050-7945-00-232 10
040-0010-129
9
77009189
VA1273-3
8
a) 054-0592-00
b) 054-0593-00
c) 054-0594-00
d) 054-0595-00
Serial Numbers:
© Midmark Corporation 2008 SF-1925
Qty.
Screw, Panhead ( 0.164 X 0.75)
050-7863-00-232 11
Models:
Description
1
[Revised: 7/14]
7
E-9.3
Always verify model & serial number
2
2
1 EA
AR
014-0775-00
117351
1
117349
4
053-2677-00
a) 177524
b) 014-0650-01
c) 275263
7
3
014-0709-00
117479
5
117698
8
a) 177531
b) 177523
c) 177529
d) 177532
10
2
6
117480
a) S059-00120
b) 002-1368-00
c) 053-1709-00
9
029-4999-00 13
016-0888-00 14
014-0687-00 15
014-0693-00 12
VA127201i
All tubing must be ordered by the foot. Therefore, the quantity ordered is the amount of feet of tubing needed.
Example: ordering an quantity of 2 would be ordering two feet of tubing.
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 2/17/16]
E-10
014-0730-00
17
117477
18
014-0707-00
19
Tubing and Fittings
11
Note
014-0526-00 16
Item
Description
Qty.
1
Connector (#8-32 to 1/8” O.D. Tube)
AR
2
Connector (#10-32 to 1/4” O.D. Tube)
AR
3
Barb Tee Fitting
AR
4
Brass Plug (#10-32 Threads)
AR
5
Uni-Clamp (1/8” O.D. Tube)
AR
6
Sleeve Clamp (1/4”O.D. Tube)
AR
7
Sealing Gasket
AR
8
Check Valve (1/8” O.D. Tube)
AR
9
Tubing
a) 2- Hole (Syringe Hose)
b) 4- Hole Handpiece Tubing Kit
c) Foot Control (Shown)
AR
10
Tubing (1/8” ID x 1/4” OD)
a) Blue
b) Red
c) Yellow
AR
11
Tubing (1/8” OD)
a) Red Tubing (.159” ID)
b) Blue Tubing (1/8” ID)
c) Clear Tubing (1/8” ID)
d) Orange Tubing (.159” ID)
AR
12
Blue Tubing (3/8” I.D.)
AR
13
Block Cross Assembly
AR
14
90 Degree Swivel Fitting (#10-32)
AR
15
Barb Tee Fitting (1/8” x 1/16” x 1/16”)
AR
16
Barb Fitting (5/32, 3/16)
AR
17
Fitting
AR
18
Fitting
AR
19
Tee, (10-32 X 1/16” BARB X 1/16” BARB)
AR
20
Not Shown - 057-0734-00
Handpiece Nut (sleeve) 4 Port (pass)
AR
Always verify model & serial number
*AR = As Required
2R-F1212-2MLessHoles
3
DP# R-F1200-2
4
1/8 OR
5/16"
Clear
1/8
GN
002-1161-00
1
5/16"
Clear
w/ Dash
1/8
BN
Note
DP #’ s are Parts Warehouse part numbers.
DP# R-F1200-4MK
5
DP# R-F1200-3B
6
DP# R-F1200-3C
7
DP# R-F12100-3A
8
18
Specify Length
When Ordering
9
DP# P-1898
10
DP# 0-2008.1
11
DP# R-F1200-3D
Foot Control Assembly
Item
12
DP# O-2012.1
17
DP# RF108116
DP# RF1025
13
15
DP# R-F1200-5 14
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 11/12/08]
E-11
DP# R-F1024
Description
Qty.
1
Foot Control Assembly (Includes Items 2 thru 18)
1
2
Shroud Valve
1
3
Dome
1
4
Retainer Ring, Dome
1
5
Spring, Dome
1
6
Valve Stem
1
7
Spring, Conical
1
8
Valve
1
9
Barb Fitting (3/16”)
2
10
O-Ring Kit
2
11
Cartridge, Valve Stem
2
12
O-ring
1
13
Screw (#6 x 1/2”)
4
14
Foot, Rubber
5
15
Screw (#4-40 x 5/16”)
2
16
Screw (#4 x 1/2”)
4
17
Base Plate
18
Foot Control Tubing, Refer to: Tubing & Fittings
Always verify model & serial number
1
AR
*AR = As Required
Athena Brand Handpieces
002-1156-00
1
002-1155-00
b
a
002-1159-00
c
2
6
5
8
a) 016-1204-00
b) 016-1204-01
c) 016-1204-02
9
a) 016-1204-03
b) 016-1204-04
c) 016-1204-05
b
a
c
002-1160-00
10
3
11
4
a
Models:
Serial Numbers:
b
All
[Revised: 4/19/16]
a) 016-1204-08
b) 016-1204-09
Description
Qty.
1
Low Speed Handpiece
2
Prophy Angle
1
1
3
Prophy Cups
10
4
Disposable Prophy Angle with Cup:
a) 10 pack
b) 200 pack
1
5
High Speed Handpiece
1
6
Fiber Optic High Speed Handpiece
Reference: Fiber Optic Components
1
7
Bur Block Kit (Including all Burs, 1 ea)
8
8
a) Round # 2 (Bur)
b) Round # 4 (Bur)
c) Round # 6 (Bur)
5 ea
9
a) Taper Fissure Crosscut # 701
b) Taper Fissure Crosscut # 701L
c) Inverted Cone # 36
5 ea
10
a) Straight Fissure Crosscut # 558
b) Straight Fissure Crosscut # 558L
5 ea
11
a) Diamond Torpedo, Fine, #869LF
b) Diamond Football, Fine, #831F
5 Ea
12
064-0031-00
Handpiece Oil
Items # 12 and # 13 are not shown
Up to V871908
© Midmark Corporation 2008 SF-1930
a) 016-1204-06
b) 016-1204-07
b
a
a) 002-1279-00
b) 002-1279-01
Athena Handpieces & Maintenance
Item
7002-1158-00
002-1157-00
E-12
Always verify model & serial number
1/4 fl. oz.
Midmark Brand Handpieces & Parts
002-1277-00
1
2
a) 002-1279-00
b) 002-1279-01
5002-1275-00
016-1362-0018
3002-1160-00
4002-1159-00
20016-1309-00
016-1310-0017
002-1276-00
6
21016-1311-00
016-1312-0019
Midmark Brand Handpieces & Parts
8002-1994-00
12016-1308-00
13002-1292-00
10016-1728-00
14002-1293-00
7002-1996-00
15002-1294-00
11016-1729-00
16002-1291-00
9002-1995-00
VA1608
Models:
Serial Numbers:
All
V871909 thru Present
© Midmark Corporation 2008 SF-1928
[Revised: 11/14/15]
E-13
Item
Description
Qty.
1
Lowspeed Instrument
1
2
Disposable Prophy Angle with Cup:
a) 10 pack
b) 200 pack
1
3
Prophy Cups
10
4
Prophy Angle
1
5
Highspeed Instrument
1
6
Fiber Optic Instrument
Reference: Fiber Optic Components
1
7
Kit, Handpiece and Coupler, High speed FO
swivel (Includes items 8 & 9)
1
8
Kit, handpiece, High speed FO Swivel
1
9
Kit, Coupler, High Speed FO Swivel
1
10
Wrench, Swivel Coupler
1
11
Conditioner Nozzle, Swivel Handpiece
1
12
5-Hole Replacement Gasket (used on items
1, 5 & 6)
1
13
Turbine *Includes item # 20
1
14
Chuck *Includes items # 20 & # 21
1
15
Head Cap * Includes items # 17 & # 20
1
16
Lowspeed Swivel Adapter * Includes items
# 12 and #18
1
17
O-Ring
1
18
O-Ring
1
19
Wave Spring
2
20
Head Cap Wrench
1
21
Spindle Cleaning Tool
1
Items 22 thru 25 Not Shown
22
002-1295-00 Water Spray Tool
1
23
002-1432-00 Handpiece Conditioner
1
24
053-2259-00 Conditioner Tube
3
25
016-1731-00 Kit, O-ring, Swivel Coupler
1
Always verify model & serial number
Midmark Brand Handpieces & Parts
2
a) 016-1204-00
b) 016-1204-01
c) 016-1204-02
3
a) 016-1204-03
b) 016-1204-04
c) 016-1204-05
4
a) 016-1204-06
b) 016-1204-07
5
a) 016-1204-08
b) 016-1204-09
a
b
c
c
b
a
1002-1158-00
a
b
Midmark Brand Handpieces & Parts
Item
a
Models:
Serial Numbers:
V871909 thru Present
© Midmark Corporation 2008 SF-1928
[Revised: 4/19/16]
E-13.1
Qty.
Bur Block Kit (Including all Burs, 1 ea)
2
a) Round # 2 (Bur)
b) Round # 4 (Bur)
c) Round # 6 (Bur)
5 ea
3
a) Taper Fissure Crosscut # 701
b) Taper Fissure Crosscut # 701L
c) Inverted Cone # 36
5 ea
4
a) Straight Fissure Crosscut # 558
b) Straight Fissure Crosscut # 558L
5 ea
5
a) Diamond Torpedo, Fine, #869LF
b) Diamond Football, Fine, #831F
5 Ea
b
All
Description
1
Always verify model & serial number
8
2120514
1120795
3016-1029-00
4016-0991-00
5016-0991-04
3
6016-1032-00
18
016-0989-00
7152055
016-1030-00
17
Syringe
Item
8120903
9016-0991-01
117660
10016-0990-00
16
DCI# 0084
15
11016-0991-03
12016-0988-00
016-1031-0014
13016-0991-02
Description
Qty.
1
Standard Syringe (Includes Items 1-19)
1
2
• Syringe Tip
1
3
• Tip adapter Assembly (DCI# 3065)
1
4
• O-Ring (DCI# 2255) (pkg of 12)
2
5
• O-Ring (DCI# 2202) (pkg of 12)
2
6
• Spring, Syringe Button (DCI# 9670)
1
7
•Button Cartridge Kit (Includes 8 thru 12 not 11)
1
8
•• Button Valve
2
9
•• O-Ring (DCI# 2203) (pkg of 12)
2
10
•• Retaining Ring (DCI# 9601)
2
11
O-Ring (DCI# 2212) (pkg of 12)
2
12
•• Pin (DCI# 9648)
1
13
O-Ring (DCI# 2211) (pkg of 12)
2
14
Syringe Handle (DCI# 3491)
1
15
Barb Fitting (DCI# 0084) (pkg of 10)
2
16
Gasket Sealing
2
17
Pin, Tip Adapter (DCI# 9659)
1
18
Spring, Tip Adapter with Body (DCI# 9677)
1
Items # 19 thru # 23 are Not Shown
Models: All (Syringe)
Serial Numbers:
© Midmark Corporation 2008 SF-1928
all
[Revised: 9/25/15]
E-14
19
•• 016-1203-05 - Ultrasonic Stones, Dog Probe
Short
1
20
•• 016-1203-06 - Ultrasonic Stones, Cat Probe
1
21
•• 016-1203-07 - Ultrasonic Stones, Dog Probe
Long
1
22
016-1502-00 - EMI Supression Core-ACTEON
Scaler
1
23
016-1717-00 - ACTEON Autoclavable Tip Box
1
Always verify model & serial number
016-1203-04
5
016-1718-01
4
3
016-1379-00
6
2
a) 016-1218-00
b) 016-1375-00
016-1380-00
7
9
8
7
10
Scaler
1
2
3
Item
6 5 4
016-1376-00 10
1
a) 002-1498-00
b) 002-1499-00
a) 016-1378-00
b) 016-1382-00
120769
8
a) 002-1002-02
b) 002-1002-05
9
Description
Qty.
1
Satelec Scaler Kit
a) with Tips & Power Supply
(Includes items 2 thru 9)
Reference: Scaler Components
b) with Tips, Power Supply and LED light
(-006 thru -008 Models Only)
(Includes items 2 thru 10)
Reference: LED Scaler Components
1
2
• Handpiece
a) Standard
b) LED
1
3
• Scaling Tip
a) Universal (Tip No. 1)
b) Voluminous Calculus (Tip No. 2)
1
4
• Scaling Tip, Shallow Pockets (Tip No. 10P)
1
5
• Scaler Tip Wrench
3
6
• Potentiometer
1
7
• Scaler Knob
1
8
• Scaler Tubing a) (Std) b) (LED)
1
9
• Scaler Control Modular a) (Std) b) (LED
1
10
• LED Light (-007, -008 Models)
1
11
Air Switch (N.O.)
1
Items # 12 thru # 18 are Not Shown
11
12
• 002-1238-00 - Scaler Tips, Ultrasonic, Vet
(Includes items 13 thru 15)
1
13
•• 016-1203-05 - Ultrasonic Stones, Dog Probe
Short
1
14
•• 016-1203-06 - Ultrasonic Stones, Cat Probe
1
15
•• 016-1203-07 - Ultrasonic Stones, Dog Probe
Long
1
Only 8000-001, -003, -005, -006, -007, -008 (Scaler)
16
016-1502-00 - EMI Supression Core-ACTEON
Scaler
1
V2200 thru V1271515
17
016-1717-00 - ACTEON Autoclavable Tip Box
1
18
016-1589-00 - Tip Wear Guide
1
VA1722-1i
Models:
a) 016-1203-00
b) 016-1203-03
Serial Numbers:
© Midmark Corporation 2008 SF-1928
[Revised: 9/25/15]
E-15
Always verify model & serial number
016-1203-04
016-1718-01
4
5
3
016-1379-00
a) 016-1203-00
b) 016-1203-03
6
016-1380-00
7
9
8
7
2
a) 016-1218-00
b) 016-1375-00
10
1
2
3
6 5 4
Scaler
Item
a) 016-1378-00
b) 016-1382-00
120769
8
1
a) 002-1002-02
b) 002-1002-05
9
11
1
2
• Handpiece
a) Standard
b) LED
1
3
• Scaling Tip
a) Universal (Tip No. 1)
b) Voluminous Calculus (Tip No. 2)
1
4
• Scaling Tip, Shallow Pockets (Tip No. 10P)
1
5
• Scaler Tip Wrench
3
6
• Potentiometer
1
7
• Scaler Knob
1
8
• Scaler Tubing a) (Std) b) (LED)
1
9
• Scaler Control Modular a) (Std) b) (LED
1
10
• LED Light (-006 thru -008 Models)
1
11
Air Switch (N.O.)
1
Items # 12 thru # 17 are Not Shown
VA1722-1i
Models:
Qty.
1
016-1376-00 10
a) 002-1498-00
b) 002-1499-00
Description
Satelec Scaler Kit
a) with Tips & Power Supply
(Includes items 2 thru 9)
Reference: Scaler Components
b) with Tips, Power Supply and LED light
(-006 thru -008 Models Only)
(Includes items 2 thru 10)
Reference: LED Scaler Components
Only 8000-001, -003, -005, -006, -007, -008 (Scaler)
Serial Numbers:
© Midmark Corporation 2008 SF-1925
V1271516 thru Present
[Revised: 9/25/15]
E-15.1
12
• 002-1238-00 - Scaler Tips, Ultrasonic, Vet
(Includes items 13 thru 15)
1
13
•• 016-1203-05 - Ultrasonic Stones, Dog Probe
Short
1
14
•• 016-1203-06 - Ultrasonic Stones, Cat Probe
1
15
•• 016-1203-07 - Ultrasonic Stones, Dog Probe
Long
1
16
016-1502-00 - EMI Supression Core-ACTEON
Scaler
1
17
016-1717-00 - ACTEON Autoclavable Tip Box
1
Always verify model & serial number
1015-2512-00
3015-2513-00
4015-2511-00
Fiber Optic Components
Item
Description
Qty.
1
•Power Pack
1
Only 8000-003 & 8000-004
2
•Shadow 5-Hole Tubing 014-0681-00-341 (Does
not include item 3) Not Shown
1
Start Production thru V933242
3
•Bulb (Not included with item 2)
1
4
•Power Supply
1
002-1237-00 Includes items # 1 thru 5
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
[Revised: 7/19/11]
E-16
Always verify model & serial number
1015-1480-00
5015-2707-00
4015-2653-00
3120722
6015-2708-00
Fiber Optic Components
Item
Models:
Only 8000-003, -004, -006, 006S, -007, 007S, -008, -008S
Serial Numbers:
© Midmark Corporation 2008 SF-1925
V933243 thru Present
[Revised: 11/7/15]
E-16.1
Description
Qty.
1
Optic Controller
1
2
Not Shown - 120721-01
Tubing 4-Hole Non-Swivel
1
3
Bulb
1
4
Power Supply
1
5
Blade Adapter (N. America - Models 8000-003,
-004, -007, -008
1
6
Blace Adapter (European - Model 8000-006)
1
Always verify model & serial number
Athena Handpiece Replacement Parts
1016-1267-01
2016-1267-00
3016-1267-02
4016-1267-06
5
a) 016-1267-03
b) 016-1267-04
6016-1267-05
Athena Handpiece Replacement Parts
Item
Description
Qty.
1
4-Hole Gasket
1
2
5-Hole Gasket
1
3
2-Hole Gasket for Little Pro
1
4
Standard & mini head push button cap wrench
5
Push Button Canister:
a) Standard Head without Cap (Fiber Optics only)
b) Mini Head without Cap (Non-Fiber Optics only)
6
Standard & mini head push button head cap
7
002-1238-00 - Scaler Tips, Ultrasonic, Vet
(Includes items 8 thru 10)
8
• 016-1203-05 - Ultrasonic Stones, Dog Probe
Short
1
9
• 016-1203-06 - Ultrasonic Stones, Cat Probe
1
10
• 016-1203-07 - Ultrasonic Stones, Dog Probe
Long
1
1
Items # 7 thru # 11 are not shown
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
all
[Revised: 1/20/10]
E-17
Always verify model & serial number
1 kit
2
053-1274-00
2
8053-1077-00
9120910
3
029-2402-00
7
10P11836
3
120908
1029-2402-01
11053-1275-00
6
053-1275-01
4
5
042-0168-03
5
VA1583
12057-0536-00
120913
6
Handpiece Holders
Item
Models:
Serial Numbers:
All
V796868 thru Present
© Midmark Corporation 2008 SF-1928
[Revised: 5/19/10]
E-18
Description
1
Syringe Holder Assembly without Sot
(Includes items 2 thru 6)
Qty.
2
• Top Housing Instrument Holder
1
3
• Pad, Instrument Holder
2
4
• Bottom Housing Without Slot
1
5
• Screw, ( MTC K3.5-1.57X20 ATF PT ZN)
4
6
• Set Screw (10-32 x 1/2”)
2
7
Handpiece Holder Assembly with Slot
(Includes items 2, 3, 5, 6, and 8 thru 12)
8
• Lever
1
9
• 3-Way Valve (Normallly Closed)
1
10
• Set Screw (6-32 x 1/4”)
1
11
• Bottom Housing With Slot
1
12
• Pivot Pin
1
Always verify model & serial number
5
121533
a) 015-0083-02
b) 015-1294-00
1
2
VA1650
a) 015-2586-00
b) 015-2665-00
4
040-0006-27
Fiber Optic Electrical Components
5
7040-0010-129
015-2666-00
3
050-8004-00-232
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
8000-005
All
[Revised: 11/7/14]
6
8000-006 & -006S
All
E-19
Item
Description
Qty.
1
LG Box
2
Receptacle
a) Domestic Models
b) Export Models (-005 & -006)
3
Metal Plate (Export Models Only, -005 & -006)
4
Outlet Cover
a) Domestic Models
Wall Plate Frame
b) Export Models (-005 & -006)
1
5
Screw (6-32 x 1/2”)
1
6
Power Supply Retainer
1
7
Screw (10-24 x 1/2” Pan Head Phillips)
6
Always verify model & serial number
1
016-1550-00
1
2016-1546-00
3016-1547-00
4016-1548-00
5016-1549-00
Scaler Components
Item
Models: 8000-001, -003, -005
Serial Numbers:
© Midmark Corporation 2008 SF-1928
All
[Revised: 1/3/13]
Description
Qty.
1
O-Ring Kit
1
8000-006
2
Nose
1
3
O-Ring (9.9 X 0.75)
1
V2200 tthru V1271515
4
Body
1
5
O-Ring (12.5 X 1.5)
1
E-20
Always verify model & serial number
2016-1549-00
016-1550-00
1
3016-1554-00
4016-1376-00
5016-1552-00
5016-1551-00
LED Scaler Components
Item
Models:
Serial Numbers:
© Midmark Corporation 2008 SF-1928
8000-006 & -006S
V1271516 thru Present
[Revised: 11/7/15
Description
Qty.
1
O-Ring Kit
1
2
O-Ring (12.5 X 1.5)
1
8000-007, -007S, -008, -008S
3
O-Ring (16 x 1)
1
4
LED Light Ring
1
All
5
LED Focus Light Guide
1
6
Nose
1
E-21
Always verify model & serial number
SUBJECT TO CHANGE WITHOUT NOTICE
Midmark Corporation
60 Vista Drive
Versailles, OH 45380 USA
1-800-643-6275
1-937-526-3662
www.midmark.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement