Rosemount 3051S MultiVariable Extension Supplement

Rosemount 3051S MultiVariable Extension Supplement
Product Data Sheet
September 2015
00813-0400-4801, Rev AB
Rosemount® 3051S MultiVariable™ Extension
Supplement
With the Rosemount 3051S MultiVariable Extensions, you can gain valuable process insight with two
measurements in one device. This reduces overall installation time and cost as well as wiring and conduit
cost.
Rosemount 3051SMV Extensions
September 2015
Rosemount 3051SMV SuperModule™ Platform
The most advanced pressure, flow, and level measurements

The all-welded hermetic SST design delivers the industry's highest field reliability

Ultra performance provides up to ±0.025% accuracy and 200:1 rangedown

15-year stability and 15-year limited warranty
Rosemount 3051SMV Series selection guide
Rosemount 3051S MultiVariable with coplanar static pressure and
temperature
See ordering information on page 3.

Coplanar platform enables integrated manifold and seal system solutions

Sensor technology allows calibrated spans from 0.3 to 4000 psi (20,7 mbar to 276 bar)

Available with 316L SST, Alloy C-276, Alloy 400, Tantalum, or gold-plated 316L SST process
isolators
Rosemount 3051S MultiVariable with in-line static pressure and
temperature
See ordering information on page 10.

Direct threaded connection, manifold or seal system solutions

Sensor technology allows calibrated spans from 0.3 to 10000 psi (20,7 mbar to 689 bar)

Available with 316L SST or Alloy C-276 process isolators
Contents
Rosemount 3051S MultiVariable with Coplanar Static Pressure
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
and Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Rosemount 3051S MultiVariable with In-line Static Pressure and
Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Rosemount 3051S MultiVariable with Coplanar Static
Pressure and Temperature
The Rosemount 3051S MultiVariable Coplanar™ pressure and temperature transmitter delivers
two measurements in one device, reducing installation time and overall project cost for a variety
of applications.
Additional information
3051SMV P-T Coplanar
Specifications: page 15
Certifications: page 24
Dimensional drawings: page 30
Specification and selection of product materials, options, or components must be made by the purchaser of the equipment. See
page 22 for more information on Material Selection.
Table 1. Rosemount 3051S Scalable™ MultiVariable Coplanar Pressure and Temperature Transmitter Ordering
Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model
Transmitter type
3051SMV
Scalable MultiVariable Transmitter
★
Performance class(1)
1
Ultra: 0.025% span SP accuracy, 200:1 rangedown, 15-year stability, 15-year limited warranty
★
2
Classic: 0.035% span SP accuracy, 150:1 rangedown, 15-year stability
★
MultiVariable type
P
★
MultiVariable measurement with direct process variable output
Measurement type
5
★
Static pressure and temperature (no DP) - coplanar style
Differential pressure range
N
★
None
Static pressure type
A
Absolute
★
G
Gage
★
Static pressure range
Absolute (A)
Gage (G)
0
Range 0
0.5 to 5 psia (0,03 to 0,34 bar)
N/A
★
1
Range 1
0 to 30 psia (0 to 2.1 bar)
-25 to 25 inH2O (-62,2 to 62,2 mbar)
★
2
Range 2
0 to 150 psia (0 to 10,3 bar)
-250 to 250 inH2O (-623 to 623 mbar)
★
3
Range 3
0 to 800 psia (0 to 55,2 bar)
-393 to 1000 inH2O (-1,0 to 2,5 bar)
★
4
Range 4
0 to 4000 psia (0 to 275,8 bar)
-14.2 to 300 psi (-0,979 to 20,7 bar)
★
5(2)
Range 5
N/A
-14.2 to 2000 psi (-0,979 to 137,9 bar) ★
www.rosemount.com
3
Rosemount 3051SMV Extensions
September 2015
Table 1. Rosemount 3051S Scalable™ MultiVariable Coplanar Pressure and Temperature Transmitter Ordering
Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Temperature input(3)
R
★
RTD input (type Pt 100, -328 to 1562 °F [-200 to 850 °C])
Isolating diaphragm
2(4)
316L SST
★
3
(4)
Alloy C-276
★
5
(2)
Tantalum
7(4)
Gold-plated 316L SST
Material type
Process connection
Connection size
Flange
material
Drain vent
Bolting
000
None (no process flange)
★
A11(5)(6)
Assemble to Rosemount 305 integral manifold
★
A12(5)
Assemble to 304 or AMF manifold with 316 SST traditional flange
★
A15(5)
Assemble to 304 or AMF manifold to SST traditional flange with Alloy C-276 drain vents
★
A16(5)
Assemble to 304 or AMF manifold to DIN SST traditional flange
★
A22(5)
Assemble AMF manifold to SST coplanar flange
★
B11(5)(7)
Assemble to one Rosemount 1199 diaphragm seal
★
Coplanar flange
1
/4–18 NPT
Carbon Steel
316 SST
N/A
★
E12
Coplanar flange
1/4–18 NPT
316 SST
316 SST
N/A
★
E13(4)
Coplanar flange
1/4–18 NPT
Cast C-276
Alloy C-276
N/A
★
E14
Coplanar flange
1
/4–18 NPT
Cast Alloy 400
Alloy 400/K-500
N/A
★
E11
E15(4)
Coplanar flange
1/4–18 NPT
SST
Alloy C-276
N/A
★
E16(4)
Coplanar flange
1/4–18 NPT
Carbon Steel
Alloy C-276
N/A
★
E21
Coplanar flange
RC 1/4
E22
E23(4)
Coplanar flange
Carbon Steel
316 SST
N/A
★
1
SST
316 SST
N/A
★
1
Cast C-276
Alloy C-276
N/A
★
1
RC /4
Coplanar flange
RC /4
E24
Coplanar flange
RC /4
Cast Alloy 400
Alloy 400/K-500
N/A
★
E25(4)
Coplanar flange
RC 1/4
SST
Alloy C-276
N/A
★
Coplanar flange
RC 1/4
Carbon Steel
Alloy C-276
N/A
★
/4–18 NPT
E26(4)
Traditional flange
1
SST
316 SST
N/A
★
F13(4)
Traditional flange
1
Cast C-276
Alloy C-276
N/A
★
F14
Traditional flange
1
/4–18 NPT
Cast Alloy 400
Alloy 400/K-500
N/A
★
Traditional flange
1/4–18 NPT
F12
F15(4)
F22
F23(4)
4
Traditional flange
Traditional flange
/4–18 NPT
SST
Alloy C-276
N/A
★
1
SST
316 SST
N/A
★
1
Cast C-276
Alloy C-276
N/A
★
RC /4
RC /4
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Table 1. Rosemount 3051S Scalable™ MultiVariable Coplanar Pressure and Temperature Transmitter Ordering
Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Material type
Process connection
F24
F25
Connection size
Drain vent
Bolting
Cast Alloy 400
Alloy 400/K-500
N/A
★
1
RC /4
SST
Alloy C-276
N/A
★
/4–18 NPT
316 SST
316 SST
/16-in. bolting
★
RC 1/4
Traditional flange
(4)
Flange
material
Traditional flange
1
7
F52
DIN-compliant traditional flange
G11
Vertical mount level flange
2-in. ANSI class 150
SST
316 SST
N/A
★
G12
Vertical mount level flange
2-in. ANSI class 300
SST
316 SST
N/A
★
G14(4)
Vertical mount level flange
2-in. ANSI class 150
Cast C-276
316 SST
N/A
★
G15(4)
Vertical mount level flange
2-in. ANSI class 300
Cast C-276
316 SST
N/A
★
G21
Vertical mount level flange
2-in. ANSI class 150
SST
316 SST
N/A
★
G22
Vertical mount level flange
2-in. ANSI class 300
SST
316 SST
N/A
★
G31
Vertical mount level flange
DIN- DN 50 PN 40
SST
316 SST
N/A
★
1/4–18 NPT
SST
316 SST
N/A
F32
F42
Bottom vent traditional flange
Bottom vent traditional flange
1
RC /4
SST
316 SST
N/A
SST
316 SST
M10 bolting
F62
DIN-compliant traditional flange
1/4–18 NPT
F72
DIN-compliant traditional flange
1/4–18 NPT
SST
316 SST
M12 bolting
G41
Vertical mount level flange
DIN- DN 80 PN 40
SST
316 SST
N/A
Transmitter output
A
4–20 mA with digital signal based on HART® protocol
Housing style
★
Material
1A
PlantWeb® housing
Aluminum
1B
PlantWeb housing
Aluminum
1J
PlantWeb housing
SST
1K
PlantWeb housing
Conduit entry size
/2–14 NPT
★
M20 ⫻ 1.5 (CM20)
★
1
/2–14 NPT
★
SST
M20 ⫻ 1.5 (CM20)
★
1
1
1C
PlantWeb housing
Aluminum
G /2
1L
PlantWeb housing
SST
G1/2
RTD cable options
Cable length
Protection type
C12
RTD input
12-ft. (3.66 m)
Shielded cable
★
C13
RTD input
24-ft. (7.32 m)
Shielded cable
★
C14
RTD input
75-ft. (22.86 m)
Shielded cable
★
C22
RTD input
12-ft. (3.66 m)
Armored shielded cable
★
C23
RTD input
24-ft. (7.32 m)
Armored shielded cable
★
Options (include with selected model number)
www.rosemount.com
5
Rosemount 3051SMV Extensions
September 2015
Table 1. Rosemount 3051S Scalable™ MultiVariable Coplanar Pressure and Temperature Transmitter Ordering
Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
RTD cable options
Cable length
Protection type
C24
RTD input
75-ft. (22.86 m)
Armored shielded cable
★
C32
RTD input
12-ft. (3.66 m)
ATEX/IECEx flameproof cable
★
C33
RTD input
24-ft. (7.32 m)
ATEX/IECEx flameproof cable
★
C34
RTD input
75-ft. (22.86 m)
ATEX/IECEx flameproof cable
★
Mounting bracket options(6)
Bracket material
Pipe/panel
Bolt material
All SST
2-in. pipe and panel
SST
★
B4
Coplanar flange bracket
B1
Traditional flange bracket
Carbon Steel
2-in. pipe
N/A
★
B2
Traditional flange bracket
Carbon Steel
Panel
N/A
★
B3
Traditional flange flat bracket
Carbon Steel
2-in. pipe
N/A
★
B7
Traditional flange bracket B1
Carbon Steel
2-in. pipe
SST
★
B8
Traditional flange bracket B2
Carbon Steel
Panel
SST
★
B9
Traditional flange bracket B3
Carbon Steel
2-in. pipe
SST
★
BA
Traditional flange bracket B1
All SST
2-in. pipe
SST
★
BC
Traditional flange bracket B3
All SST
2-in. pipe
SST
★
Software configuration
C1
Custom software configuration (A Configuration Data Sheet must be completed, see document number
00806-0100-4803).
★
C4
NAMUR alarm and saturation levels, high alarm
★
C5
NAMUR alarm and saturation levels, low alarm
★
C6
Custom alarm and saturation signal levels, high alarm
★
C7
Custom alarm and saturation signal levels, low alarm
★
C8
Low alarm (standard Rosemount alarm and saturation levels)
★
Process adapters(8)
D2
D9
1
/2-14 NPT process adapter
★
1
RC /2 SST flange adapter
External ground screw assembly(9)
D4
External ground screw assembly
★
Drain/vent valve(8)
D5
Remove transmitter drain/vent valves and install plugs
D7
Coplanar flange without drain/vent ports
★
Conduit plug(10)
DO
6
316 SST conduit plug
★
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Table 1. Rosemount 3051S Scalable™ MultiVariable Coplanar Pressure and Temperature Transmitter Ordering
Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Product certifications
E1
ATEX Flameproof
★
I1
ATEX Intrinsic Safety
★
N1
ATEX Type n
★
ND
ATEX Dust
★
K1
ATEX Flameproof, Intrinsic Safety, Type n, Dust (combination of E1, I1, N1, and ND)
★
E4
TIIS Flameproof
★
E5
FM Explosion-proof, Dust Ignition-proof
★
I5
FM Intrinsically Safe; Division 2
★
K5
FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination E5 and I5)
★
E6(11)(12)
CSA Explosion-proof, Dust Ignition-proof, Division 2
★
I6
CSA Intrinsically Safe
★
K6(11)(12)
CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination E6 and I6)
★
E7
IECEx Flameproof
★
I7
IECEx Intrinsic Safety
★
N7
IECEx Type n
★
K7
IECEx Flameproof, Intrinsic Safety, and Type n (combination of E7, I7, and N7)
★
E2
INMETRO Flameproof
★
I2
INMETRO Intrinsic Safety
★
E3
China Flameproof
★
I3
China Intrinsic Safety
★
KA(11)(12)
ATEX and CSA Explosion-proof, Intrinsically Safe, Division 2 (combination E1, E6, I1and I6)
★
KB(11)(12)
FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination E5, I5, E6, and I6)
★
KC(12)
FM and ATEX Explosion-proof, Intrinsically Safe, Division 2 (combination E5, I5, E1, and I1)
★
KD(11)(12)
FM, CSA, and ATEX Explosion-proof, Intrinsically Safe (combination E5, E6, E1, I5, I6 and I1)
★
Drinking water approval(13)
DW
NSF drinking water certification
★
Shipboard approvals
SBS
American bureau of shipping
★
Alternate materials of construction
L1
Inert sensor fill fluid (Gage sensors only) Note: Silicone fill fluid is standard.
★
L2
Graphite-filled PTFE O-ring
★
L4(8)
Austenitic 316 SST bolts
★
L5(8)
ASTM A193, Grade B7M bolts
★
L6(8)
Alloy K-500 bolts
★
www.rosemount.com
7
Rosemount 3051SMV Extensions
September 2015
Table 1. Rosemount 3051S Scalable™ MultiVariable Coplanar Pressure and Temperature Transmitter Ordering
Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Alternate materials of construction(8)
L7(14)
ASTM A453, Class D, Grade 660 bolts
★
L8
ASTM A193, Class 2, Grade B8M bolts
★
Digital display
M5
PlantWeb LCD display
★
Special procedures
P1(15)
Hydrostatic testing with certificate
P2(8)
Cleaning for special services
P3(8)
Cleaning for less than 1PPM chlorine/fluorine
★
Special certification
Q4
Calibration certificate
★
QP
Calibration data certificate and tamper evident seal
★
Transient protection(9)
T1
Transient terminal block
Material traceability certification
Q8
Material traceability certification per EN 102043.1
Surface finish certification
Q16
Surface finish certification for sanitary remote seals
Toolkit total system performance reports(16)
QZ
Remote seal system performance calculation report
Conduit electrical connector(17)
GE
M12, 4-pin, male connector (eurofast®)
★
GM
A size Mini, 4-pin, male connector (minifast®)
★
NACE® certificates(18)
Q15
Certificate of Compliance to NACE MR0175/ISO 15156 for wetted materials
★
Q25
Certificate of Compliance to NACE MR0103 for wetted materials
★
Cold temperature
BRR
-58 °F (-50 °C) cold temperature start-up
Typical model number:
8
★
3051SMV 1 P 5 N A 4 R 2 E12 A 1A C12 B4 C1 M5
1.
For detailed specifications see “Specifications” on page 15.
2.
Specification for gage pressure only.
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
3.
RTD Sensor must be ordered separately.
4.
Materials of Construction comply with metallurgical requirements highlighted within NACE MR0175/ISO 15156 for sour oil field production environments
Environmental limits apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining
environments. Order with Q15 or Q25 to receive a NACE certificate.
5.
“Assemble to” items are specified separately and require a completed model number.
6.
For Process connection option code A11, the mounting bracket must be ordered as part of the manifold model number.
7.
Consult an Emerson™ Process Management representative for performance specifications.
8.
Not available with process connection option code A11.
9.
This assembly is included with transient terminal block and certification options E1, N1, K1, ND, E4, E7, N7, K7, E2, E3, KA, KC, and KD.
10. Transmitter is shipped with 316 SST conduit plug (uninstalled) in place of standard carbon steel conduit plug.
11. Not available with M20 or G 1/2 conduit entry size.
12. RTD cable not available with this option.
13. Requires 316L SST diaphragm material, glass-filled PTFE O-ring (standard), and process connection code E12 or F12.
14. Bolts are not considered process wetted. In instances where NACE MR0175/ ISO 15156 and NACE MR0103 conformance is required for bolting, L7 is the
recommended bolting option.
15. Not available with SP range 0 with absolute.
16. Remote Seal System Performance Calculation Report is only available with process connection B11.
17. Available with Intrinsically Safe approvals only. For FM Intrinsically Safe; Nonincendive approve; (option code I5), install in accordance with Rosemount drawing
03152-1009.
18. NACE compliant wetted materials are identified by Footnote 4.
www.rosemount.com
9
Rosemount 3051SMV Extensions
September 2015
Rosemount 3051S MultiVariable with In-line Static
Pressure and Temperature
The Rosemount 3051S MultiVariable in-line pressure and temperature transmitter delivers two
measurements in one device reducing installation time and overall project cost for a variety of
applications.
Additional information
Specifications: page 15
Certifications: page 24
Dimensional drawings: page 30
3051SMV P-T in-line
Specification and selection of product materials, options, or components must be made by the purchaser of the equipment. See
page 22 for more information on Material Selection.
Table 2. Rosemount 3051S Scalable MultiVariable In-line Pressure and Temperature Transmitter Ordering
Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model
Transmitter type
3051SMV
Scalable MultiVariable Transmitter
★
Performance class(1)
1
Ultra: 0.025% span SP accuracy, 200:1 rangedown, 15-year stability, 15-year limited warranty
★
2
Classic: 0.035% span SP accuracy, 150:1 rangedown, 15-year stability
★
MultiVariable type
P
★
MultiVariable measurement with direct process variable output
Measurement type
6
★
Static pressure and temperature (no DP) – in-line style
Differential pressure range
N
★
None
Static pressure type
A
Absolute
★
G
Gage
★
Static pressure range
Absolute
Gage
1
Range 1
0 to 30 psia (0 to 2,1 bar)
-14.7 to 30 psig (-1,0 to 2,1 bar)
★
2
Range 2
0 to 150 psia (0 to 10,3 bar)
-14.7 to 150 psig (-1,0 to 10,3 bar)
★
3
Range 3
0 to 800 psia (0 to 55,2 bar)
-14.7 to 800 psig (-1,0 to 55,2 bar)
★
4
Range 4
0 to 4000 psia (0 to 275,8 bar)
-14.7 to 4000 psig (-1,0 to 275,8 bar)
★
5(2)
Range 5
0 to 10000 psia (0 to 689 bar)
N/A
★
10
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Table 2. Rosemount 3051S Scalable MultiVariable In-line Pressure and Temperature Transmitter Ordering
Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Temperature input(3)
R
★
RTD input (type Pt 100, -328 to 1562 °F [-200 to 850 °C])
Isolating diaphragm(4)
2
316L SST
★
3
Alloy C-276
★
Process connection
A11(5)
Assemble to Rosemount 306 integral manifold
★
B11(5)(6)
Assemble to one Rosemount 1199 diaphragm seal
★
K11
1/2–14 NPT female
★
M11(7)
G1/2A DIN 16288 male
★
L11(7)
Non-threaded instrument flange (I-flange)
Transmitter output
A
★
4–20 mA with digital signal based on HART protocol
Housing style
Material
1A
PlantWeb housing
Aluminum
1B
PlantWeb housing
Conduit entry size
/2–14 NPT
★
Aluminum
M20 ⫻ 1.5 (CM20)
★
★
★
1
1J
PlantWeb housing
SST
1/2–14 NPT
1K
PlantWeb housing
SST
M20 ⫻ 1.5 (CM20)
1C
PlantWeb housing
Aluminum
G1/2
1L
PlantWeb housing
SST
G1/2
RTD cable options
Cable length
Protection type
C12
RTD input
12-ft. (3.66 m)
Shielded cable
★
C13
RTD input
24-ft. (7.32 m)
Shielded cable
★
C14
RTD input
75-ft. (22.86 m)
Shielded cable
★
C22
RTD input
12-ft. (3.66 m)
Armored shielded cable
★
C23
RTD input
24-ft. (7.32 m)
Armored shielded cable
★
C24
RTD input
75-ft. (22.86 m)
Armored shielded cable
★
C32
RTD input
12-ft. (3.66 m)
ATEX/IECEx flameproof cable
★
C33
RTD input
24-ft. (7.32 m)
ATEX/IECEx flameproof cable
★
C34
RTD input
75-ft. (22.86 m)
ATEX/IECEx flameproof cable
★
All SST
2-in. pipe and panel SST
★
Options (include with selected model number)
Mounting brackets(8)
B4
In-line bracket
www.rosemount.com
11
Rosemount 3051SMV Extensions
September 2015
Table 2. Rosemount 3051S Scalable MultiVariable In-line Pressure and Temperature Transmitter Ordering
Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Software configuration
C1
Custom software configuration (A Configuration Data Sheet must be completed, see document number
00806-0100-4803).
★
C4
NAMUR alarm and saturation levels, high alarm
★
C5
NAMUR alarm and saturation levels, low alarm
★
C6
Custom alarm and saturation signal levels, high alarm
★
C7
Custom alarm and saturation signal levels, low alarm
★
C8
Low alarm (standard Rosemount alarm and saturation levels)
★
External ground screw assembly(9)
D4
★
External ground screw assembly
Conduit plug(10)
DO
★
316 SST conduit plug
Product certifications
E1
ATEX Flameproof
★
I1
ATEX Intrinsic Safety
★
N1
ATEX Type n
★
ND
ATEX Dust
★
K1
ATEX Flameproof, Intrinsic Safety, Type n, Dust (combination of E1, I1, N1, and ND)
★
E4
TIIS Flameproof
★
E5(11)
FM Explosion-proof, Dust Ignition-proof
★
I5
FM Intrinsically Safe, Division 2
★
K5(11)
FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination E5 and I5)
★
E6(11)(12)
CSA Explosion-proof, Dust Ignition-proof, Division 2
★
I6
CSA Intrinsically Safe
★
K6(11)(12)
CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination E6 and I6)
★
E7
IECEx Flameproof
★
I7
IECEx Intrinsic Safety
★
N7
IECEx Type n
★
K7
IECEx Flameproof, Intrinsic Safety, and Type n (combination E7, I7, and N7)
★
E2
INMETRO Flameproof
★
I2
INMETRO Intrinsic Safety
★
E3
China Flameproof
★
I3
China Intrinsic Safety
★
KA(11)(12)
ATEX and CSA Explosion-proof, Intrinsically Safe, Division 2 (combination E1, E6, I1and I6)
★
KB(11)(12)
FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination E5, I5, E6, and I6)
★
12
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Table 2. Rosemount 3051S Scalable MultiVariable In-line Pressure and Temperature Transmitter Ordering
Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Product certifications
KC(11)
KD
(11)(12)
FM and ATEX Explosion-proof, Intrinsically Safe, Division 2 (combination E5, I5, E1, and I1)
★
FM, CSA, and ATEX Explosion-proof, Intrinsically Safe (combination E5, E6, E1, I5, I6 and I1)
★
Drinking water approval(13)
DW
NSF drinking water certification
★
Shipboard approvals
SBS
American Bureau of Shipping
★
Alternate materials of construction
L1
Inert sensor fill fluid (Gage sensors only) Note: Silicone fill fluid is standard.
★
Digital display
M5
PlantWeb LCD display
★
Special procedures
P1
Hydrostatic testing with certificate
P2(14)
Cleaning for special services
P3(14)
Cleaning for less than 1PPM chlorine/fluorine
★
Special certification
Q4
Calibration certificate
★
QP
Calibration certificate and tamper evident seal
★
Material traceability certification
Q8
Material traceability certification per EN 10204 3.1B
★
Surface finish certification
Q16
Surface finish certification for sanitary remote seals
★
Toolkit total system performance reports(15)
QZ
Remote seal system performance calculation report
★
Terminal block(9)
T1
Transient terminal block
★
Conduit electrical connector(16)
GE
M12, 4-pin, male connector (eurofast)
★
GM
A size Mini, 4-pin, male connector (minifast)
★
NACE certificate
(17)
Q15
Certificate of Compliance to NACE MR0175/ISO 15156 for wetted materials
★
Q25
Certificate of Compliance to NACE MR0103 for wetted materials
★
www.rosemount.com
13
Rosemount 3051SMV Extensions
September 2015
Table 2. Rosemount 3051S Scalable MultiVariable In-line Pressure and Temperature Transmitter Ordering
Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Cold temperature
BRR
★
-58 °F (-50 °C) cold temperature start-up
Typical model number:
3051SMV 1 P 6 N G 3 R 2 A11 A1 A M5
1.
For detailed specifications see “Specifications” on page 15.
2.
Specification for absolute pressure only.
3.
RTD Sensor must be ordered separately.
4.
Materials of Construction comply with metallurgical requirements highlighted within NACE MR0175/ISO 15156 for sour oil field production environments
Environmental limits apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining
environments. Order with Q15 or Q25 to receive a NACE certificate.
5.
“Assemble to” items are specified separately and require a completed model number.
6.
Consult an Emerson Process Management representative for performance specifications.
7.
Range 1-4 only.
8.
For process connection option code A11, the mounting bracket must be ordered as part of the manifold model number.
9.
This assembly is included with transient terminal block and certification options E1, N1, K1, ND, E4, E7, N7, K7, E2, E3, KA, KC, and KD.
10. Transmitter is shipped with 316 SST conduit plug (uninstalled) in place of standard carbon steel conduit plug.
11. Not available with M20 or G 1/2 conduit entry size.
12. RTD cable not available with this option.
13. Requires 316L SST diaphragm material, glass-filled PTFE O-ring (standard), and process connection option code K11 or M11.
14. Not available with process connection option code A11.
15. Remote Seal System Performance Calculation Report is only Available with process connection B11.
16. Available with Intrinsically Safe approvals only. For FM Intrinsically Safe; Nonincendive approval (option code I5), install in accordance with Rosemount drawing
03151-1009.
17. NACE compliant wetted materials are identified by Footnote 4.
14
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Specifications
Performance specifications
For zero-based spans, reference conditions, silicone oil fill, glass-filled PTFE o-rings, SST materials, Coplanar flange (3051SMV _ _5) or
1
/2-in.– 14 NPT (3051SMV _ _6) process connections, digital trim values set to equal range points.
Conformance to specification (±3σ [Sigma])
Technology leadership, advanced manufacturing techniques, and statistical process control ensure pressure measurement
specification conformance to ±3σ or better.
Reference accuracy
Stated reference accuracy equations include terminal based linearity, hysteresis, and repeatability.
Transmitter with coplanar sensor module
Gage pressure (3051SMV_ _5)
Ultra
Classic
Ranges 2 - 4
±0.025% of span;
For spans less than 10:1,
±(0.005 + 0.0035[URL/Span])% of span
±0.035% of span;
For spans less than 10:1,
±(0.015 + 0.005[URL/Span])% of span
Range 5
±0.05% of span;
For spans less than 10:1,
±(0.005 + 0.0045[URL/Span])% of span
±0.065% of span;
For spans less than 10:1,
±(0.015 + 0.005[URL/Span])% of span
Range 1
±0.09% of span;
For spans less than 15:1,
±(0.015 + 0.005[URL/Span])% of span
±0.10% of span;
For spans less than 15:1,
±(0.025 + 0.005[URL/Span])% of span
Absolute pressure (3051SMV_ _5)
Ultra
Classic
Ranges 1 - 4
±0.025% of span;
For spans less than 10:1,
±0.004% of URL
±0.035% of span;
For spans less than 10:1,
±0.0065% of URL
Range 0
±0.075% of span;
For spans less than 5:1,
±(0.025 + 0.01[URL/Span])% of span
±0.075% of span;
For spans less than 5:1,
±(0.025 + 0.01[URL/Span])% of span
Transmitter with in-line sensor module
Absolute pressure (3051SMV_ _6)
Gage pressure (3051SMV_ _6)
Ultra
Classic
Ranges 1 - 4
±0.025% of span;
For spans less than 10:1,
±0.004% of URL
±0.035% of span;
For spans less than 10:1,
±0.0065% of URL
Range 5(1)
±0.04% of span;
For spans less than 10:1,
±0.004% of URL
±0.065% of span;
For spans less than 10:1,
±0.0065% of URL
1.
Specification for absolute pressure only.
www.rosemount.com
15
Rosemount 3051SMV Extensions
September 2015
Process temperature RTD interface
Process temperature (3051SMV_ _5 or 6)
±0.67 °F (0.37 °C)
Transmitter total performance(1)
Total performance is based on combined errors of reference accuracy, ambient temperature effect, and line pressure effect at
normal operating conditions (70% of span typical reading, 740 psi [51 bar] line pressure).
Models
3051SMV_ _5
3051SMV_ _6
Ultra
Ranges 2-4 (A) ±0.1% of span;
Ranges 2-5 (G) For ±50 °F (28 °C) temperature changes;
0-100% relative humidity,
Ranges 2-4
from 1:1 to 5:1 rangedown
Classic
±0.14% of span;
For ±50 F (28 °C) temperature changes,
0-100% relative humidity,
from 1:1 to 5:1 rangedown
Long term stability
Pressure
Models
3051SMV_ _5
Ranges 2-5
3051SMV_ _6
Ranges 1-5
Ultra
Classic
±0.15% of URL for 15 years;
for ±50 °F (28 °C) temperature changes,
up to 1000 psi (68,95 bar) line pressure
±0.20% of URL for 15 years;
for ±50 °F (28 °C) temperature changes,
up to 1000 psi (68,95 bar) line pressure
Process temperature(2)
Models
3051SMV _ _5 or 6
RTD Interface
The greater of ±0.185 °F (0.103 °C) or 0.1% of reading per year (excludes RTD sensor
stability).
Warranty(3)
Ultra
Classic
15-year limited warranty(4)
1-year limited warranty(5)
1.
Transmitter Total Performance specification applies to pressure measurement only.
2.
Specifications for process temperature are for the transmitter portion only. The transmitter is compatible with any Pt 100 (100 ohm platinum) RTD. Examples of
compatible RTDs include the Rosemount Series 68 and 78 RTD Temperature Sensors.
3.
Warranty details can be found in Emerson Process Management Terms and Conditions of Sale, Document 63445, Rev G (10/06).
4.
Rosemount Ultra transmitters have a limited warranty of fifteen (15) years from date of shipment. All other provisions of Emerson Process Management standard
limited warranty remain the same.
5.
Goods are warranted for twelve (12) months from the date of initial installation or eighteen (18) months from the date of shipment by seller, whichever period
expires first.
16
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Dynamic performance
Total time response at 75 °F (24 °C), includes dead time
3051SMV_ _5
3051SMV_ _6
Range 1: 310 ms
Range 2: 170 ms
Range 3-5: 155 ms
140 ms
Dead time
3051SMV _ _5 or 6
100 ms (nominal)
Sensor update rate
3051SMV_ _ 5 or 6
SP
22 updates per sec.
RTD Interface
1 update per sec.
Ambient temperature effect
Transmitter with coplanar sensor module
Gage pressure: (3051SMV_ _5)
Ultra
per 50 °F (28 °C)
Classic
per 50 °F (28 °C)
Ranges 2 - 5
±(0.009% URL + 0.025% span) from 1:1 to 10:1;
±(0.0125% URL +0.0625% span) from 1:1 to 5:1;
±(0.018% URL + 0.08% span) from >10:1 to 200:1 ±(0.025% URL + 0.125% span) from >5:1 to 150:1
Range 1
±(0.1% URL + 0.25% span) from 1:1 to 50:1
±(0.1% URL + 0.25% span) from 1:1 to 50:1
Absolute pressure: (3051SMV_ _5)
Ultra
per 50 °F (28 °C)
Classic
per 50 °F (28 °C)
Ranges 2-4
±(0.0125% URL + 0.0625% span) from 1:1 to 5:1; ±(0.0125% URL + 0.0625% span) from 1:1 to 5:1;
±(0.025% URL + 0.125% span) from >5:1 to 200:1 ±(0.025% URL + 0.125% span) from >5:1 to 150:1
Range 0
±(0.1% URL + 0.25% span) from 1:1 to 30:1
Range 1
±(0.0125% URL + 0.0625% span) from 1:1 to 5:1; ±(0.0125% URL + 0.0625% span) from 1:1 to 5:1;
±(0.025% URL + 0.125% span) from >5:1 to 100:1 ±(0.025% URL + 0.125% span) from >5:1 to 100:1
www.rosemount.com
±(0.1% URL + 0.25% span) from 1:1 to 30:1
17
Rosemount 3051SMV Extensions
September 2015
Transmitter with in-line sensor module
Absolute pressure (3051SMV_ _6)
Gage pressure (3051SMV_ _6)
Ultra
per 50 °F (28 °C)
Classic
per 50 °F (28 °C)
Ranges 2-4
±(0.009% URL + 0.025% span) from 1:1 to 10:1;
±(0.0125% URL + 0.0625% span) from 1:1 to 5:1;
±(0.018% URL + 0.08% span) from >10:1 to 200:1 ±(0.025% URL + 0.125% span) from >5:1 to 150:1
Range 5(1)
±(0.05% URL + 0.075% span) from 1:1 to 10:1
Range 1
±(0.0125% URL + 0.0625% span) from 1:1 to 5:1; ±(0.0125% URL + 0.0625% span) from 1:1 to 5:1;
±(0.025% URL + 0.125% span) from >5:1 to 100:1 ±(0.025% URL + 0.125% span) from >5:1 to 100:1
±(0.05% URL + 0.075% span) from 1:1 to 5:1
Process temperature RTD interface(2)
Process temperature (3051SMV_ _5 or 6)
Classic and Ultra
per 50 °F (28 °C)
±0.39 °F (0,216 °C) per 50 °F (28 °C)
Mounting position effects
Models
Ultra and Classic MV
3051SMV _ _5 or 6
Zero shifts to ±2.5 inH2O (6,22 mbar), which can be zeroed
Span: no effect
3051SMV _ _5 (G)
Zero shifts to ±1.25 inH2O (3,11 mbar), which can be zeroed
Span: no effect
1.
Specification for absolute pressure only.
2.
Specifications for process temperature are for the transmitter portion only. The transmitter is compatible with any Pt 100 (100 ohm platinum) RTD. Examples of
compatible RTDs include Rosemount series 68 and 78 RTD Temperature Sensors.
Vibration effect
Electro Magnetic Compatibility (EMC)(1)
Less than ±0.1% of URL when tested per the requirements of
IEC60770-1 field or pipeline with high vibration level (10 - 60 Hz
0.21 mm displacement peak amplitude/60-2000 Hz 3g).
Meets all relevant requirements of EN 61326-1.
For Housing Style codes 1J, 1K, and 1L:
Less than ±0.1% of URL when tested per the requirements of
IEC60770-1 field with general application or pipeline with low
vibration level (10 - 60 Hz 0.15 mm displacement peak
amplitude/60-500 Hz 2g).
Transient protection (option T1)
Tested in accordance with IEEE C62.41.2-2002,
Location Category B
6 kV crest (0.5 μs - 100 kHz)
3 kA crest (8 ⫻ 20 microseconds)
6 kV crest (1.2 ⫻ 50 microseconds)
Power supply effect
Less than ±0.005% of calibrated span per volt change in voltage
at the transmitter terminals
1.
18
3051SMV requires shielded cable for both temperature and loop wiring.
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Functional specifications
Range and sensor limits
Transmitter with coplanar sensor module
GP Sensor (3051SMV_ _5)
Range
AP Sensor (3051SMV_ _5)
Lower (LRL)(1)
Upper (URL)
Lower (LRL)
Upper (URL)
0
N/A
N/A
0 psia (0 bar)
5.00 psia (0,34 bar)
1
-25.00 inH2O (-62,16 mbar)
25.00 inH2O (62,16 mbar)
0 psia (0 bar)
30.00 psia (2,06 bar)
2
-250.00 inH2O (-621,60 mbar)
250.00 inH2O (621,60 mbar)
0 psia (0 bar)
150.00 psia (10,34 bar)
3
0.50 psia (34,47 mbar)
1000.00 inH2O (2,48 bar)
0 psia (0 bar)
800.00 psia (55,15 bar)
4
0.50 psia (34,47 mbar)
300.00 psi (20,68 bar)
0 psia (0 bar)
4000.00 psia (275,79 bar)
5
0.50 psia (34,47 mbar)
2000.00 psi (137,89 bar)
N/A
N/A
1.
Assumes atmospheric pressure of 14.7 psia (1 bar-a).
Transmitter with in-line sensor module
GP Sensor (3051SMV_ _6)
Range
1.
AP Sensor (3051SMV_ _6)
Lower (LRL)(1)
Upper (URL)
Lower (LRL)
Upper (URL)
1
-14.70 psig (-1,01 bar)
30.00 psig (2,06 bar)
0 psia (0 bar)
30.00 psia (2,06 bar)
2
-14.70 psig (-1,01 bar)
150.00 psig (10,34 bar)
0 psia (0 bar)
150.00 psia (10,34 bar)
3
-14.70 psig (-1,01 bar)
800.00 psig (55,15 bar)
0 psia (0 bar)
800.00psia (55,15 bar)
4
-14.70 psig (-1,01 bar)
4000.00 psig (275,79 bar)
0 psia (0 bar)
4000.00 psia (275,79 bar)
5
N/A
N/A
0 psia (0 bar)
10000.00 psia (689,47 bar)
Assumes atmospheric pressure of 14.7 psia (1 bar-a).
Process temperature RTD Interface (3051SMV_ _5 or 6)(1)
1.
Lower (LRL)
Upper (URL)
-328 °F (-200 °C)
1562 °F (850 °C)
Transmitter is compatible with any Pt 100 RTD sensor. Examples of compatible RTDs include Rosemount Series 68 and 78 RTD Temperature Sensors.
www.rosemount.com
19
Rosemount 3051SMV Extensions
September 2015
Minimum span limits
Transmitter with coplanar sensor module
GP Sensor (3051SMV_ _5)
AP Sensor (3051SMV_ _5)
Range
Ultra
Classic
Ultra
Classic
0
N/A
N/A
0.167 psia (11,51 mbar)
0.167 psia (11,51 mbar)
1
0.50 inH2O (1,24 mbar)
0.50 inH2O (1,24 mbar)
0.30 psia (20,68 mbar)
0.30 psia (20,68 mbar)
2
1.25 inH2O (3,11 mbar)
1.67 inH2O (4,15 mbar)
0.75 psia (51,71 mbar)
1.00 psia (68,94 mbar)
3
5.00 inH2O (12,43 mbar)
6.67 inH2O (16,58 mbar)
4.00 psia (275,79 mbar)
5.33 psia (367,49 mbar)
4
1.50 psig (103,42 mbar)
2.00 psig (137,89 mbar)
20.00 psia (1,38 bar)
26.67 psia (1,83 bar)
5
10.00 psig (689,48 mbar)
13.33 psig (919,01 bar)
N/A
N/A
Transmitter with in-line sensor module
GP Sensor (3051SMV_ _6)
AP Sensor (3051SMV_ _6)
Range
Ultra
Classic
Ultra
Classic
1
0.30 psig (20,68 mbar)
0.30 psig (20,68 mbar)
0.30 psia (20,68 mbar)
0.30 psia (20,68 mbar)
2
0.75 psig (51,71 mbar)
1.00 psig (68,94 mbar)
0.75 psia (51,71 mbar)
1.00 psia (68,94 mbar)
3
4.00 psig (275,79 mbar)
5.33 psig (367,49 mbar)
4.00 psia (275,79 mbar)
5.33 psia (367,49 mbar)
4
20.00 psig (1,38 bar)
26.67 psig (1,83 bar)
20.00 psia (1,38 bar)
26.67 psia (1,83 bar)
5
N/A
N/A
1000.00 psia (68,95 bar)
2000.00 psia (137,89 bar)
Process temperature RTD Interface
(3051SMV_ _5 or 6)
Minimum Span = 52 °F (11 °C)
Service
3051SMV
Power supply
External power supply required.
3051SMV: 12 to 42.4 Vdc with no load
3051SMV_ _ 5 or 6
Maximum Loop Resistance = 43.5 ⫻ (Power Supply Voltage – 12.0)
Liquid, gas, and vapor applications
Zero and span adjustment
Zero and span values can be set anywhere within the range.
Span must be greater than or equal to the minimum span.
Output
Two-wire 4–20 mA is user-selectable for linear or square root
output. Digital process variable superimposed on 4–20 mA
signal, available to any host that conforms to the HART protocol.
20
Load (Ohms)
4–20 mA HART
1322
1000
500
Operating
Region
0
12.0
20
30
Voltage (Vdc)
42.4
The Field Communicator requires a minimum loop resistance of
250Ω for communication.
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Overpressure limits
Temperature limits
Transmitters withstand the following limits without damage:
Ambient
Coplanar sensor module (single variable)
-40 to 185 °F (-40 to 85 °C)
With LCD display(1): -40 to 175 °F (-40 to 80 °C)
With option code P0: -20 to 185 °F (-29 to 85 °C)
Range
GP (3051SMV_ _5)
AP (3051SMV_ _5)
0
N/A
60 psia (4,14 bar)
1
2000 psi (137,90 bar)
750 psia (51,71 bar)
2
3626 psi (250,00 bar)
1500 psia (103,42 bar)
3
3626 psi (250,00 bar)
1600 psia (110,32 bar)
4
3626 psi (250,00 bar)
6000 psia (413,69 bar)
5
3626 psi (250,00 bar)
N/A
In-line sensor module
Range
AP (3051SMV_ _6)
750 psi (51,71 bar)
2
1500 psi (103,42 bar)
3
1600 psi (110,32 bar)
4
6000 psi (413,69 bar)
5(1)
15000 psi (1034,21 bar)
Specification for absolute pressure only.
Maximum working pressure limits
Maximum working pressure is the maximum pressure allowed
for normal transmitter operation. For a gage or absolute
pressure transmitter, the maximum working pressure is the
same as the Upper Range Limit (URL). The maximum working
pressure of transmitters with assemble-to options is limited by
the lowest maximum pressure rating of the individual
components.
Storage
-50 to 185 °F (-46 to 85 °C)
With LCD display: -40 to 185 °F (-40 to 85 °C)
Process temperature limits
At atmospheric pressures and above:(1)
3051SMV_ _5
Silicone fill sensor(2)
with coplanar flange
-40 to 250 °F (-40 to 121 °C)(3)
with traditional flange
-40 to 300 °F (-40 to 149 °C)(3)
with level flange
-40 to 300 °F (-40 to 149 °C)(3)
with 305 integral
manifold
-40 to 300 °F (-40 to 149 °C)(3)
Inert fill sensor(2)
Silicone fill sensor(2)
-40 to 250 °F (-40 to 121 °C)(3)
Inert fill sensor(2)
-22 to 250 °F (-30 to 121 °C)(3)
1.
Upper temperature limit is 464 °F (240 °C) for a 2-in. direct-mount
extension, 500 °F (260 °C) for a 4-in. direct-mount extension.
2.
Process temperatures above 185 °F (85 °C) require derating the ambient
limits by a 1.5:1 ratio. For example, for process temperature of 195 °F (91
°C), new ambient temperature limit is equal to 170 °F (77 °C). This can be
determined as follows:
(195 °F - 185 °F) ⫻ 1.5 = 15 °F,
185 °F - 15 °F = 170 °F
3.
220 °F (104 °C) limit in vacuum service; 130 °F (54 °C) for pressures below
0.5 psia.
4.
For 3051SMV _ _ 5, 160 ° F (71 °C) limit in vacuum service.
5.
Not available for 3051SMV _ _ 5_A.
Coplanar sensor module (3051SMV_ _5)
10000 psig (689,47 bar)
In-line sensor module (3051SMV_ _6)

Ranges 1-4: 11000 psi (758,42 bar)
Range 5: 26000 psi (1792,64 bar)(1)
1.
-40 to 185 °F (-40 to 85 °C)(4)(5)
3051SMV_ _6
Burst pressure limits

LCD display may not be readable and LCD display updates will be slower
at temperatures below -4 °F (-20 °C).
Coplanar sensor module
GP (3051SMV_ _6)
1
1.
1.
For absolute pressure only.
www.rosemount.com
21
Rosemount 3051SMV Extensions
September 2015
Humidity limits
Physical specifications
0–100% relative humidity
Material selection
Turn-on time
When power is applied to the transmitter during startup,
performance will be within specifications per the time period
described below:
Transmitter
Turn-on time (typical)
3051SMV
5 seconds
Volumetric displacement
Less than 0.005 in3 (0,08 cm3)
Damping
Analog output response time to a step change is user-selectable
from 0 to 60 seconds for one time constant. For 3051SMV, each
variable can be individually adjusted. Software damping is in
addition to sensor module response time.
Emerson provides a variety of Rosemount products with various
product options and configurations including materials of
construction that can be expected to perform well in a wide
range of applications. The Rosemount product information
presented is intended as a guide for the purchaser to make an
appropriate selection for the application. It is the purchaser’s
sole responsibility to make a careful analysis of all process
parameters (such as all chemical components, temperature,
pressure, flow rate, abrasives, contaminants, etc.), when
specifying product materials, options, and components for the
particular application. Emerson Process Management is not in a
position to evaluate or guarantee the compatibility of the
process fluid or other process parameters with the product
options, configuration, or materials of construction selected.
Electrical connections
1/2–14 NPT, G1/2, and M20 ⫻ 1.5 conduit. HART interface
Failure mode alarm
connections fixed to terminal block for Output code A.
4-20 mA HART (output option code A)
Process connections
If self-diagnostics detect a gross transmitter failure, the analog
signal will be driven offscale to alert the user. Rosemount
standard (default), NAMUR, and custom alarm levels are
available (see Alarm configuration below).
High or low alarm signal is hardware-selectable via the switch.
Alarm configuration
Coplanar sensor module (3051SMV_ _5)
Standard
1/4-18 NPT on 21/8-in. centers
Flange
Adapters
1/2-14 NPT and RC 1/2 on 2-in. (50.8 mm), 21/8-in.
(54.0 mm), or 2 1/4-in. (57.2 mm) centers
In-line sensor module (3051SMV_ _6)
High alarm
Low alarm
K11
1
Default
≥ 21.75 mA
≤ 3.75 mA
L11
NAMUR compliant(1)
≥ 22.5 mA
≤ 3.6 mA
Non-threaded instrument flange
(available in SST for sensor ranges 1-4 only)
20.2 - 23.0 mA
3.6 - 3.8 mA
M11
G 1/2 A DIN 16288 male
(available in SST for sensor ranges 1-4 only)
Custom levels(2)
1.
Analog output levels are compliant with NAMUR recommendation NE
43, see option codes C4 or C5.
2.
Low alarm must be 0.1 mA less than low saturation and high alarm must
be 0.1 mA greater than high saturation.
/2-14 NPT Female
Process-wetted parts
Process isolating diaphragms
Coplanar sensor module (3051SMV_ _5)
316L SST (UNS S31603), Alloy C-276 (UNS N10276),
Gold-plated 316L SST
B11
Low side process connection is SST
In-line sensor module (3051SMV_ _6)
316L SST (UNS S31603), Alloy C-276 (UNS N10276)
22
www.rosemount.com
September 2015
Drain/vent valves
316 SST, Alloy C-276, or Alloy 400/K-500 material
(Drain vent seat: Alloy 400, Drain vent stem: Alloy K-500)
Process flanges and flange adapters
Plated carbon steel
SST: CF-8M (Cast 316 SST) per ASTM A743
Cast C-276: CW-12MW per ASTM A494
Cast Alloy 400: M-30C per ASTM A494
Wetted O-rings
Glass-filled PTFE
Non-wetted parts
Electronics housing
Low-copper aluminum alloy or CF-8M (Cast 316 SST)
NEMA 4X, IP 66, IP 68 (66 ft [20 m] for 168 hours)
Coplanar sensor module housing
SST: CF-3M (Cast 316L SST)
Bolts
Plated carbon steel per ASTM A449, Type 1
Austenitic 316 SST per ASTM F593
ASTM A453, Class D, Grade 660 SST
ASTM A193, Grade B7M alloy steel
ASTM A193, Class 2, Grade B8M SST
Alloy K-500
Sensor module fill fluid
Silicone is standard.
Inert is available as option code (L1).(1)
Inert for in-line series uses Fluorinert™ FC-43.
Inert for Coplanar series uses Halocarbon.
Paint for aluminum housing
Polyurethane
Cover O-rings
Rosemount 3051SMV Extensions
Sensor module weights
Coplanar sensor module(1)
3.1 lb (1,4 kg)
In-line sensor module
1.4 lb (0,6 kg)
1.
Flange and bolts not included.
Transmitter weights(1)
Transmitter with coplanar sensor module
(3051SMV_ _5)
PlantWeb housing, SST Flange
Transmitter with in-line sensor module
(3051SMV_ _6)
PlantWeb housing
1.
3.7 lb (1,7 kg)
Fully functional transmitter with sensor module, housing, terminal
block, and covers. Does not include LCD display.
Transmitter option weights
Option
code
Option
Add
lb. (kg)
1J, 1K, 1L
SST PlantWeb housing
3.5 (1,6)
1A, 1B, 1C Aluminum PlantWeb housing
1.1 (0,5)
M5
LCD display for Aluminum PlantWeb
0.8 (0,4)
housing(1),
1.6 (0,7)
LCD display for SST PlantWeb housing(1)
B4
SST Mounting Bracket for Coplanar
Flange
1.2 (0,5)
B4
SST Mounting Bracket for in-line
1.3 (0,6)
1.
Includes LCD display and display cover.
Transmitter component weights
Item
Weight
lb. (kg)
Aluminum Standard Cover
0.4 (0,2)
SST Standard Cover
1.3 (0,6)
Aluminum Display Cover
0.7 (0,3)
SST Display Cover
1.5 (0,7)
LCD Display(1)
0.1 (0,04)
PlantWeb Terminal Block
0.2 (0,1)
Buna-N
1.
1.
6.7 lb (3,1 kg)
Display only.
Inert is not available with 3051SMV _ _ 5_A.
www.rosemount.com
23
Rosemount 3051SMV Extensions
September 2015
Product Certifications
Rev 1.2
European Directive Information
IE
A copy of the EC Declaration of Conformity can be found at the
end of the Quick Start Guide. The most recent revision of the EC
Declaration of Conformity can be found at
www.rosemount.com.
FM FISCO
Certificate: 3031960
Standards: FM Class 3600 – 2011, FM Class 3610 – 2010,
FM Class 3611 – 2004, FM Class 3616 – 2006,
FM Class 3810 – 2005, NEMA 250 – 1991
Markings: IS CL I, DIV 1, GP A, B, C, D;
T4(-50 °C ≤ Ta ≤ +70 °C); when connected per
Rosemount drawing 03151-1006; Type 4X
Ordinary Location Certification
Canada
As standard, the transmitter has been examined and tested to
determine that the design meets the basic electrical,
mechanical, and fire protection requirements by a nationally
recognized test laboratory (NRTL) as accredited by the Federal
Occupational Safety and Health Administration (OSHA).
E6
CSA Explosionproof, Dust-Ignitionproof, and Division 2
Certificate: 1143113
Standards: CAN/CSA C22.2 No. 0-10, CSA Std C22.2 No.
25-1966, CSA Std C22.2 No. 30-M1986,
CAN/CSA C22.2 No. 94-M91, CSA Std C22.2
No. 142-M1987, CSA Std C22.2 No.
213-M1987, ANSI/ISA 12.27.01-2003, CSA
Std C22.2 No. 60529:05
Markings: Explosionproof Class I, Division 1, Groups B, C,
D; Dust-Ignitionproof Class II, Division 1,
Groups E, F, G; Class III; suitable for Class I,
Division 2, Groups A, B, C, D; Type 4X
I6
CSA Intrinsically Safe
Certificate: 1143113
Standards: CAN/CSA C22.2 No. 0-10, CSA Std C22.2 No.
30-M1986, CAN/CSA C22.2 No. 94-M91, CSA
Std C22.2 No. 142-M1987, CSA Std C22.2 No.
157-92, ANSI/ISA 12.27.01-2003, CSA Std
C22.2 No. 60529:05
Markings: Intrinsically Safe Class I, Division 1; suitable for
Class 1, Zone 0, IIC, T3C; when connected per
Rosemount drawing 03151-1207; Type 4X
IF
CSA FISCO
Certificate: 1143113
Standards: CAN/CSA C22.2 No. 0-10, CSA Std C22.2 No.
30-M1986, CAN/CSA C22.2 No. 94-M91, CSA
Std C22.2 No. 142-M1987, CSA Std C22.2 No.
157-92, ANSI/ISA 12.27.01-2003, CSA Std
C22.2 No. 60529:05
Markings: FISCO Intrinsically Safe Class I, Division 1;
Groups A, B, C, D; suitable for Class I, Zone 0;
T3C; when installed per Rosemount drawing
03151-1207; Type 4X
Installing Equipment in North America
The US National Electrical Code (NEC) and the Canadian
Electrical Code (CEC) permit the use of Division marked
equipment in Zones and Zone marked equipment in Divisions.
The markings must be suitable for the area classification, gas,
and temperature class. This information is clearly defined in the
respective codes.
USA
E5
I5
FM Explosionproof (XP) and Dust-Ignitionproof (DIP)
Certificate: 3008216
Standards: FM Class 3600 – 2011, FM Class 3615 – 2006,
FM Class 3616 – 2011, FM Class 3810 – 2005,
ANSI/NEMA 250 – 2003
Markings: XP CL I, DIV 1, GP B, C, D; DIP CL II, DIV 1, GP E,
F, G; CL III; T5(-50 °C ≤ Ta ≤ +85 °C); Factory
Sealed; Type 4X
FM Intrinsic Safety (IS) and Nonincendive (NI)
Certificate: 3031960
Standards: FM Class 3600 – 2011, FM Class 3610 – 2007,
FM Class 3611 – 2004, FM Class 3810 – 2005,
NEMA 250 – 1991
Markings: IS CL I, DIV 1, GP A, B, C, D; CL II, DIV 1, GP E, F,
G; Class III; Class 1, Zone 0 AEx ia IIC T4; NI CL 1,
DIV 2, GP A, B, C, D; T4(-50 °C ≤ Ta ≤ +70 °C)
when connected per Rosemount drawing
03151-1206; Type 4X
Note
Transmitters marked with NI CL 1, DIV 2 can be installed in
Division 2 locations using general Division 2 wiring methods or
Nonincendive Field Wiring (NIFW). See Drawing 03151-1206.
24
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Europe
E1
IA
ATEX Flameproof
Certificate: KEMA 00ATEX2143X
Standards: EN 60079-0:2012, EN 60079-1: 2007,
EN 60079-26:2007 (3051SFx models with RTD
are certified to EN 60079-0:2006)
Markings:
II 1/2 G Ex d IIC T6…T4 Ga/Gb,
T6(-60 °C ≤ Ta ≤ +70 °C),
T5/T4(-60 °C ≤ Ta ≤ +80 °C)
Temperature class
Process temperature
T6
-60 °C to +70 °C
T5
-60 °C to +80 °C
T4
-60 °C to +120 °C
Special Conditions for Safe Use (X):
1. The device contains a thin wall diaphragm. Installation,
maintenance and use shall take into account the
environmental conditions to which the diaphragm will be
subjected. The manufacturer’s instructions for installation
and maintenance shall be followed in detail to assure
safety during its expected lifetime.
2. For information on the dimensions of the flameproof joints
the manufacturer shall be contacted.
I1
ATEX FISCO
Certificate: Baseefa08ATEX0064X
Standards: EN 60079-0: 2012, EN 60079-11: 2012
Markings:
II 1 G Ex ia IIC T4 Ga, T4(-60 °C ≤ Ta ≤ +70 °C)
ATEX Intrinsic Safety
Certificate: Baseefa08ATEX0064X
Standards: EN 60079-0: 2012, EN 60079-11: 2012
Markings:
II 1 G Ex ia IIC T4 Ga, T4(-60 °C ≤ Ta ≤ +70 °C)
Parameters
HART
FOUNDATION SuperModule
Fieldbus
only
RTD
(for
3051SFx)
Voltage Ui
30 V
30 V
7.14 V
30 V
Current Ii
300 mA
300 mA
300 mA
2.31 mA
Power Pi
1W
1.3 W
887 mW
17.32 mW
14.8 nF
0
0.11 μF
0
0
0
0
0
Capacitance Ci
Inductance Li
Special Conditions for Safe Use (X):
Parameters
FISCO
Voltage Ui
17.5 V
Current Ii
380 mA
Power Pi
5.32 W
Capacitance Ci
0
Inductance Li
0
ND ATEX Dust
Certificate: BAS01ATEX1374X
Standards: EN 60079-0: 2012, EN 60079-31: 2009
Markings:
II 1 D Ex ta IIIC T105 °C T500 95 °C Da,
(-20 °C ≤ Ta ≤ +85 °C), Vmax = 42.4V
Special Conditions for Safe Use (X):
1. Cable entries must be used which maintain the ingress
protection of the enclosure to at least IP66.
2. Unused cable entries must be filled with suitable blanking
plugs which maintain the ingress protection of the
enclosure to at least IP66.
3. Cable entries and blanking plugs must be suitable for the
ambient temperature range of the apparatus and capable
of withstanding a 7J impact test.
4. The SuperModule(s) must be securely screwed in place to
maintain the ingress protection of the enclosure(s).
N1
ATEX Type n
Certificate: Baseefa08ATEX0065X
Standards: EN 60079-0: 2012, EN 60079-15: 2010
Markings:
II 3 G Ex nA IIC T4 Gc, (-40 °C ≤ Ta ≤ 70 °C),
Vmax = 45V
Special Condition for Safe Use (X):
1. If fitted with a 90 V transient suppressor, the equipment is
not capable of withstanding the 500 V electrical strength
test as defined in Clause 6.5.1 of EN 60079-15:2010. This
must be taken into account during installation.
1. If the equipment is fitted with the optional 90 V transient
suppressor, it is incapable of withstanding the 500 V
isolation from earth test and this must be taken into
account during installation.
2. The enclosure may be made of aluminum alloy and given a
protective polyurethane paint finish; however, care should
be taken to protect it from impact or abrasion if located in
a Zone 0 environment.
www.rosemount.com
25
Rosemount 3051SMV Extensions
International
E7
September 2015
I7
IECEx Flameproof and Dust
Certificate: IECEx KEM 08.0010X (Flameproof)
Standards: IEC 60079-0:2011, IEC 60079-1: 2007,
IEC 60079-26:2006 (3051SFx models with RTD
are certified to IEC 60079-0:2004)
Markings: Ex d IIC T6…T4 Ga/Gb, T6(-60 °C ≤ Ta ≤ +70 °C),
T5/T4(-60 °C ≤ Ta ≤ +80 °C)
IECEx Intrinsic Safety
Certificate: IECEx BAS 08.0025X
Standards: IEC 60079-0: 2011, IEC 60079-11: 2011
Markings: Ex ia IIC T4 Ga, T4(-60 °C ≤ Ta ≤ +70 °C)
HART
Parameters
FOUNDATION SuperModule
Fieldbus
only
RTD
(for
3051SFx)
Voltage Ui
30 V
30 V
7.14 V
30 V
Temperature class
Process temperature
Current Ii
300 mA
300 mA
300 mA
2.31 mA
T6
-60 °C to +70 °C
Power Pi
1W
1.3 W
887 mW
17.32 mW
T5
-60 °C to +80 °C
Capacitance Ci
14.8 nF
0
0.11 μF
0
T4
-60 °C to +120 °C
0
0
0
0
Special Conditions for Safe Use (X):
Inductance Li
Special Conditions for Safe Use (X):
1. If the equipment is fitted with the optional 90 V transient
suppressor, it is incapable of withstanding the 500 V
isolation from earth test and this must be taken into
account during installation.
1. The device contains a thin wall diaphragm. Installation,
maintenance and use shall take into account the
environmental conditions to which the diaphragm will be
subjected. The manufacturer’s instructions for installation
and maintenance shall be followed in detail to assure
safety during its expected lifetime.
2. The enclosure may be made of aluminum alloy and given a
protective polyurethane paint finish; however, care should
be taken to protect it from impact or abrasion if located in
a Zone 0 environment.
2. For information on the dimensions of the flameproof joints
the manufacturer shall be contacted.
Certificate: IECEx BAS 09.0014X (Dust)
Standards: IEC 60079-0:2011, IEC 60079-31:2008
Markings: Ex ta IIIC T105 °C T500 95 °C Da,
(-20 °C ≤ Ta ≤ +85 °C), Vmax = 42.4V
IG
IECEx FISCO
Certificate: IECEx BAS 08.0025X
Standards: IEC 60079-0: 2011, IEC 60079-11: 2011
Markings: Ex ia IIC T4 Ga, T4(-60 °C ≤ Ta ≤ +70 °C)
Parameters
FISCO
1. Cable entries must be used which maintain the ingress
protection of the enclosure to at least IP66.
Voltage Ui
17.5 V
2. Unused cable entries must be filled with suitable blanking
plugs which maintain the ingress protection of the
enclosure to at least IP66.
Current Ii
380 mA
Power Pi
5.32 W
Special Conditions for Safe Use (X):
3. Cable entries and blanking plugs must be suitable for the
ambient temperature range of the apparatus and capable
of withstanding a 7J impact test.
4. The 3051S - SuperModule must be securely screwed in
place to maintain the ingress protection of the enclosure.
N7
Capacitance Ci
0
Inductance Li
0
IECEx Type n
Certificate: IECEx BAS 08.0026X
Standards: IEC 60079-0: 2011, IEC 60079-15: 2010
Markings: Ex nA IIC T5 Gc, (-40 °C ≤ Ta ≤ 70 °C)
Special Condition for Safe Use (X):
1. If fitted with a 90 V transient suppressor, the equipment is
not capable of withstanding the 500 V electrical strength
test as defined in Clause 6.5.1 of IEC 60079-15:2010. This
must be taken into account during installation.
26
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Brazil
China
E2
E3
INMETRO Flameproof
Certificate: NCC 12.1128X[Mfg USA]
Standards: ABNT NBR IEC 60079-0:2008, ABNT NBR IEC
60079-1:2009, ABNT NBR IEC 60079-26:2008
Markings: Ex d IIC T* Ga/Gb, T6(-50 °C ≤ Ta ≤ +65 °C),
T5(-50 °C ≤ Ta ≤ +80 °C)
Special Conditions for Safe Use (X):
1. For processes with temperatures above 135 ° C, you should
evaluate whether the SuperModule temperature class is
appropriate to apply, for these applications there is a risk
of SuperModule temperature is above the temperature
class T5, and this temperature is a function of the type of
vent used on the apparatus.
2. The plugs Ex d, cable glands and wiring shall be suitable for
a temperature of +90 ° C.
3. The model 3051 contains a diaphragm with a thin wall.
Installation, maintenance and use shall take into account
environmental conditions to which the diaphragm is to be
used. The manufacturer's instructions for maintenance
shall be followed in detail to assure safety during its
lifetime.
4. In the case of repair, contact the manufacturer for
information on interstitial dimensions of the
explosion-proof joints.
I2
INMETRO Intrinsic Safety
Certificate: UL-BR 15.0357X[Mfg USA, Germany, SMMC]
Standards: ABNT NBR IEC 60079-0:2008, ABNT NBR IEC
60079-11:2009
Markings: Ex ia IIC T4 Ga, (-60 °C ≤ Ta ≤ +70 °C)
Special Conditions for Safe Use (X):
1. If the equipment is fitted with the optional 90V transient
suppressor, it is incapable of withstanding the 500V
isolation from earth test and this must be taken into
account during installation.
2. The enclosure may be made of aluminium alloy and given
a protective polyurethane paint finish; however, care
should be taken to protect it from impact or abrasion if
located in a Zone 0 environment, areas requiring EPL Ga.
Parameters
HART
SuperModule
RTD
only
(for 3051SFx)
Voltage Ui
30 V
7.14 V
30 V
Current Ii
300 mA
300 mA
2.31 mA
Power Pi
1W
887 mW
17.32 mW
14.8 nF
0.11 μF
0
0
0
0
Capacitance Ci
Inductance Li
www.rosemount.com
China Flameproof and Dust Ignition-proof
Certificate: 3051SMV: GYJ14.1039X [Mfg USA, China,
Singapore]
3051SFx: GYJ11.1711X [Mfg USA, China,
Singapore]
Standards: 3051SMV: GB3836.1-2010, GB3836.2-2010,
GB3836.20-2010
3051SFx: GB3836.1-2010, GB3836.2-2010,
GB3836.20-2010, GB12476.1-2000
Markings: 3051SMV: Ex d IIC T6/T5 Ga/Gb
3051SFx: Ex d IIC T6/T5 Ga/Gb; DIP A20
TA 105 °C; IP66
Special Conditions for Safe Use (X):
1. Symbol “X” is used to denote specific conditions of use: For
information on the dimensions of the flameproof joints the
manufacturer shall be contacted.
2. The relationship between T code and ambient
temperature range are as follows:
T code Ambient temperature range
T6
-50 °C ~ +65 °C
T5
-50 °C ~ +80 °C
3. The earth connection facility in the enclosure should be
connected reliably.
4. During installation, use and maintenance of the product in
explosive atmosphere, observe the warning “Do not open
cover when circuit is alive”. During installation, use, and
maintenance in explosive dust atmosphere, observe the
warning “Do not open when an explosive dust atmosphere
is present”.
5. During installation there should be no mixture harmful to
the housing.
6. During installation, use and maintenance in explosive dust
atmosphere, product enclosure should be cleaned to avoid
dust accumulation, but compressed air should not be
used.
7. During installation in a hazardous location, cable glands
and blanking plugs certified by state appointed inspection
bodies with Ex d IIC Gb or Ex d IIC Gb DIP A20 [Flowmeters]
IP66 type of protection should be used. Redundant cable
entries should be blocked with blanking plugs.
8. End users are not permitted to change any components,
but to contact the manufacturer to avoid damage to the
product.
9. Maintenance should be done when no explosive gas and
dust atmosphere is present.
27
Rosemount 3051SMV Extensions
September 2015
10. During installation, use and maintenance of this product,
observe following standards:
GB3836.13-1997 “Electrical apparatus for explosive gas
atmospheres Part 13: Repair and overhaul for apparatus
used in explosive gas atmospheres”
GB3836.15-2000 “Electrical apparatus for explosive gas
atmospheres Part 15: Electrical installations in hazardous
area (other than mines)”
GB3836.16-2006 “Electrical apparatus for explosive gas
atmospheres Part 16: Inspection and maintenance of
electrical installation (other than mines)”
GB50257-1996 “Code for construction and acceptance of
electric device for explosion atmospheres and fire hazard
electrical equipment installation engineering”
I3
China Intrinsic Safety
Certificate: 3051SMV: GYJ14.1040X [Mfg USA, China,
Singapore]
3051SFx: GYJ11.1707X [Mfg USA, China,
Singapore]
Standards: 3051SMV: GB3836.1-2010, GB3836.4-2010,
GB3836.20-2010
3051SFx: GB3836.1/4-2010,
GB3836.20-2010, GB12476.1-2000
Markings: 3051SMV: Ex ia IIC T4 Ga
3051SFx: Ex ia IIC T4 Ga, DIP A20 TA105 °C
IP66
Special Conditions for Safe Use (X):
1. The enclosure may contain light metal, attention should
be taken to avoid ignition hazard due to impact or friction.
2. The apparatus is not capable of withstanding the 500V
electrical strength test defined in Clause 6.3.12 of
GB3836.4-2010.
EAC – Belarus, Kazakhstan, Russia
3. Ambient temperature range: -60 °C ~ +70 °C.
4. Intrinsically safe electric parameters:
Maximum
input
voltage:
Ui (V)
Maximum
input
current:
Ii (mA)
Maximum
input
power:
Pi (W)
30
300
1.0
6. The product should be used with Ex certified associated
apparatus to establish explosion protection system that
can be used in explosive gas atmospheres. Wiring and
terminals should comply with the instruction manual of
the product and associated apparatus.
7. End users are not permitted to change any components,
contact the manufacturer to avoid damage to the
product.
8. During installation in hazardous location, cable glands,
conduit, and blanking plugs certified by state-appointed
inspection bodies with DIP A20 IP66 type of protection
should be used. Redundant cable entries should be
blocked with blanking plugs.
9. During installation, use, and maintenance in explosive
dust atmosphere, observe the warning “Do not open
when an explosive dust atmosphere is present”.
10. Maintenance should be done when no explosive dust
atmosphere is present.
11. When installation, use and maintenance of this product,
observe following standards:
GB3836.13-1997 “Electrical apparatus for explosive gas
atmospheres Part 13: Repair and overhaul for apparatus
used in explosive gas atmospheres“
GB3836.15-2000 “Electrical apparatus for explosive gas
atmospheres Part 15: Electrical installations in hazardous
area (other than mines)”
GB3836.16-2006 “Electrical apparatus for explosive gas
atmospheres Part 16: Inspection and maintenance of
electrical installation (other than mines)”
GB50257-1996- “Code for construction and acceptance of
electric device for explosion atmospheres and fire hazard
electrical equipment installation engineering”
Maximum internal
parameters:
Ci (nF)
Li (μH)
14.8
0
EM Technical Regulation Customs Union (EAC) Flameproof
Certificate: RU C-US.GB05.B.00835
Markings: Ga/Gb Ex d IIC T6…T4 X
IM
Technical Regulation Customs Union (EAC) Intrinsic Safety
Certificate: RU C-US.GB05.B.00835
Markings: 0Ex ia IIC T4 Ga X
Japan
E4 Japan Flameproof
Maximum Maximum Maximum Maximum
Certificate:TC19070, TC19071, TC19072, TC19073
external
output
output
output
Markings: Ex d IIC T6
parameters:
voltage:
current:
power:
Ui (V)
Ii (mA)
Pi (W) C (nF) L (μH) Republic of Korea
i
i
RTD
SuperModule
30
2.31
17.32
0
0
7.14
300
8871.0
110
0
5. The cables between this product and associated apparatus
should be shielded cables. The shield should be grounded
reliably in non-hazardous area.
28
EP
Republic of Korea Flameproof
Certificate: 12-KB4BO-0180X [Mfg USA],
11-KB4BO-0068X [Mfg Singapore]
Markings: Ex d IIC T5 or T6
IP
Republic of Korea Intrinsic Safety
Certificate: 10-KB4BO-0021X [Mfg USA, SMMC]
Markings: Ex ia IIC T4
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Combinations
K1
Combination of E1, I1, N1, and ND
K2
Combination of E2 and I2
K5
Combination of E5 and I5
K6
Combination of E6 and I6
K7
Combination of E7, I7, and N7
KA
Combination of E1, I1, E6, and I6
KB
Combination of E5, I5, E6, and I6
KC
Combination of E1, I1, E5, and I5
KD
Combination of E1, I1, E5, I5, E6, and I6
KM Combination of EM and IM
KP
Combination of EP and IP
Additional Certifications
SBS American Bureau of Shipping (ABS) Type Approval
Certificate: 00-HS145383
Intended Use: Measure gauge or absolute pressure of
liquid, gas or vapor applications on ABS
classed vessels, marine, and offshore
installations.
SBV Bureau Veritas (BV) Type Approval
Certificate:
31910 BV
Requirements: Bureau Veritas Rules for the Classification of
Steel Ships
Application: Class Notations: AUT-UMS, AUT-CCS,
AUT-PORT and AUT-IMS
SDN Det Norske Veritas (DNV) Type Approval
Certificate: A-13243
Intended Use: Det Norske Veritas’ Rules for Classification of
Ships, High Speed and Light Craft, and Det
Norske Veritas’ Offshore Standards
Application:
Location classes
Type
3051S
Temperature
D
Humidity
B
Vibration
A
EMC
A
Enclosure
D/IP66/IP68
SLL Lloyds Register (LR) Type Approval
Certificate: 11/60002
Application: Environmental categories ENV1, ENV2, ENV3,
and ENV5
D3
Custody Transfer – Measurement Canada Accuracy
Approval Certificate: AG-0501, AV-2380C
www.rosemount.com
29
Rosemount 3051SMV Extensions
September 2015
Dimensional Drawings
Figure 1. Transmitter with Coplanar Sensor Module and Flange - PlantWeb Housing
Front view
Side view
4.51
(115)
4.20
(107)
8.57
(218)
9.67
(246)
6.44
(164)
Dimensions are in inches (millimeters).
Figure 2. Transmitter with Coplanar Sensor Module and Traditional Flange - PlantWeb Housing
Front view
Side view
9.30
(236)
1.63
(41)
3.40
(86)
1.10
(28)
2.13
(54)
Dimensions are in inches (millimeters).
30
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Figure 3. Transmitter with In-line Sensor Module - PlantWeb Housing(1)
Front view
Side view
5.17
(131)
4.20
(107)
8.04
(204)
Dimensions are in inches (millimeters).
Figure 4. PlantWeb Housing with In-line SuperModule Platform
4.51
(115)
7.97
(202)
1.37
(35)
A
2.40
(61)
A. I-flange process connector
Dimensions are in inches (millimeters).
1.
For ranges 1A-4A, 1/2-in. NPT 316L SST process wetted connection. For detailed dimensions on other configurations, see Type I drawings at rosemount.com.
www.rosemount.com
31
Rosemount 3051SMV Extensions
September 2015
Figure 5. Traditional Mounting Configurations
Pipe mount
Pipe mount (flat bracket)
Panel mount
10.71
(272)
2.62
(67)
8.10
(205)
8.10
(205)
0.93
(24)
3.40
(86)
2.62
(67)
4.85
(123)
7.70
(196)
3.40
(86)
Dimensions are in inches (millimeters).
Figure 6. In-line Mounting Configurations (B4 Bracket)
Pipe mount (front)
Pipe mount (side)
Panel mount (side)
4.51
(115)
2.59
(65)
3.08
(78)
6.15
(156)
6.25
(159)
2.81
(71)
4.72
(120)
Dimensions are in inches (millimeters).
32
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Figure 7. Rosemount 3051SMV Scalable Transmitter with FF Seal(1)(2)
Coplanar style
5.17
(131)
4.51
(115)
4.20
(107)
8.57
(218)
3.62
(92)
+ Direct Mount
Extension Length
In-line style
4.20
(107)
5.17
(131)
8.04
(204)
1.50
(38)
Dimensions are in inches (millimeters).
1.
FF (FFW) seal dimensions and pressure ratings can be found in the Rosemount DP Level Transmitters and 1199 Remote Seals Product Data Sheet (document number
00813-0100-4016).
2.
Lower housing (flushing ring) is available with FFW style flange.
www.rosemount.com
33
Rosemount 3051SMV Extensions
September 2015
Figure 8. Rosemount 3051SMV Scalable Transmitter with EF Seal(1)
Coplanar style
5.17
4.51 (131)
(115)
4.20
(107)
8.57
(218)
3.62
(92)
+ Direct Mount
Extension Length
In-line style
5.17
(131)
4.20
(107)
8.04
(204)
1.50
(38)
Dimensions are in inches (millimeters).
1.
34
EF (EFW) seal dimensions and pressure ratings can be found in the Rosemount DP Level Transmitters and 1199 Remote Seals Product Data Sheet (document number
00813-0100-4016).
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Figure 9. Rosemount 3051SMV Scalable Transmitter with RF Seal(1)
Coplanar style
5.21
(132)
4.2
(107)
4.51
(115)
8.57
(218)
3.62
(92)
+ Direct Mount
Extension Length
In-line style
5.17
(131)
4.20
(107)
8.04
(204)
1.50
(38)
Dimensions are in inches (millimeters).
1.
RF (RFW) seal dimensions and pressure ratings can be found in the Rosemount DP Level Transmitters and 1199 Remote Seals Product Data Sheet (document number
00813-0100-4016).
www.rosemount.com
35
Rosemount 3051SMV Extensions
September 2015
Figure 10. Rosemount 3051SMV Scalable Transmitter with RT Seal(1)
Coplanar style
5.17
(131)
4.20
(107)
4.51
(115)
8.57
(218)
3.62
(92)
+ Direct Mount
Extension Length
In-line style
4.20
(107)
4.51
(115)
8.04
(204)
1.50
(38)
Dimensions are in inches (millimeters).
1.
36
RT (RTW) seal dimensions can be found in the Rosemount DP Level Transmitters and 1199 Remote Seals Product Data Sheet (document number 00813-0100-4016).
www.rosemount.com
September 2015
Rosemount 3051SMV Extensions
Figure 11. Rosemount 3051SMV Scalable Transmitter with SS Seal(1)
Coplanar style
5.17
(131)
4.51
(115)
4.20
(107)
8.57
(218)
3.62
(92)
+ Direct Mount
Extension Length
In-line style
4.20
(107)
5.17
(131)
8.04
(204)
1.50
(38)
Dimensions are in inches (millimeters).
1.
SS (SSW) seal dimensions and pressure ratings can be found in the Rosemount DP Level Transmitters and 1199 Remote Seals Product Data Sheet (document number
00813-0100-4016).
www.rosemount.com
37
Rosemount 3051SMV Extensions
September 2015
Figure 12. Rosemount 3051SMV Scalable Transmitter with SC Seal(1)
Coplanar style
5.17
(131)
4.51
(115)
4.20
(107)
8.57
(218)
3.62
(92)
+ Direct Mount
Extension Length
In-line style
5.17
(131)
4.20
(107)
8.04
(204)
1.50
(38)
Dimensions are in inches (millimeters).
1.
38
SC (SCW) seal dimensions and pressure ratings can be found in the Rosemount DP Level Transmitters and 1199 Remote Seals Product Data Sheet (document number
00813-0100-4016).
www.rosemount.com
September 2015
www.rosemount.com
Rosemount 3051SMV Extensions
39
Rosemount 3051SMV Extensions
00813-0400-4801, Rev AB
Product Data Sheet
September 2015
Global Headquarters
Emerson Process Management
6021 Innovation Blvd.
Shakopee, MN 55379, USA
+1 800 999 9307 or +1 952 906 8888
+1 952 949 7001
[email protected]
North America Regional Office
Emerson Process Management
8200 Market Blvd.
Chanhassen, MN 55317, USA
+1 800 999 9307 or +1 952 906 8888
+1 952 949 7001
[email protected]
Latin America Regional Office
Emerson Process Management
1300 Concord Terrace, Suite 400
Sunrise, Florida, 33323, USA
+1 954 846 5030
+1 954 846 5121
[email protected]
Europe Regional Office
Emerson Process Management Europe GmbH
Neuhofstrasse 19a P.O. Box 1046
CH 6340 Baar
Switzerland
+41 (0) 41 768 6111
+41 (0) 41 768 6300
[email protected]
Asia Pacific Regional Office
Emerson Process Management Asia Pacific Pte Ltd
1 Pandan Crescent
Singapore 128461
+65 6777 8211
+65 6777 0947
[email protected]
Middle East and Africa Regional Office
Emerson Process Management
Emerson FZE P.O. Box 17033,
Jebel Ali Free Zone - South 2
Dubai, United Arab Emirates
+971 4 8118100
+971 4 8865465
[email protected]
Standard Terms and Conditions of Sale can be found at:
www.rosemount.com\terms_of_sale.
The Emerson logo is a trademark and service mark of Emerson Electric Co.
Rosemount and Rosemount logotype are registered trademarks of Rosemount Inc.
PlantWeb is a registered trademark of one of the Emerson Process Management
group of companies.
Coplanar, MultiVariable, Scalable, and SuperModule are trademarks of Rosemount
Inc.
HART is a registered trademark of the FieldComm Group.
Fluorinert is a trademark of 3M.
eurofast and minifast are registered trademarks of TURCK.
NACE is a registered trademark of NACE International.
All other marks are the property of their respective owners.
© 2015 Rosemount Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement