Century 4024 [Rev A] [0500797] [01/1999]

Century 4024 [Rev A] [0500797] [01/1999]
CENTURY
L E G E N D A R Y
®
L E A D E R S H I P
OWNER'S MANUAL
4024T / T2
INSTALLATION, OPERATION, MAINTENANCE & PARTS
NOTE: MANUAL including SPECIFICATIONS, subject to change without notice
All ratings specified are based on structural factors only,
not vehicle capacities or capabilities.
CENTURY®
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Phone (423) 238-4171 • FAX (423) 238-5371
FORM NO. 0500797
REV. A
1 / 99
PRICE $25.00
LIMITED WARRANTY
MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the
original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in
material and workmanship for a period of twelve (12) months from date placed in service, but in no event
shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The
purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event
shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve
(12) months from date placed in service, whichever is earlier.
MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at
the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon
inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be
used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not
obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or
replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or
alterations have been made unless authorized by MILLER.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER
WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime,
claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages
concerning or relating to any product or parts, whether based on negligence, strict liability, breach of
contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss
resulted from any general or particular requirement which MILLER knew or had reason to know about at
the time of sale.
MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS
MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO
PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any
accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR
PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such
warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted
under applicable law, pass on to the purchaser such manufacturer's or seller's warranty.
MILLER, whose policy is one of continuous improvement, reserves the right to improve its products
through changes in design or materials as it may deem desirable without being obligated to incorporate
such changes in products previously sold. This warranty is not intended to cover or include the following
items, which are set forth by way of example and not limitation:
A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to
weather, road conditions, road treatments, etc.
B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure
to provide reasonable and necessary maintenance, or uses for which the equipment was not
designed or intended.
C. Alterations or modifications that affect performance, operation or reliability.
D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud
flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts.
IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER
PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY
OTHER IMPROPER USE.
SERIAL NUMBER
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Telephone (423) 238-4171
Section VI - PARTS
This Section is provided by the manufacturer for the purpose of ordering
any component part of the CENTURY 4024 Wrecker / Integrated Underlift
that may be required when part replacement is necessary. Be certain to use
only original equipment replacement parts for warranty purposes as well as
for keeping your CENTURY 4024 Wrecker / Integrated Underlift in its
original state and optimum operating capacities. When ordering replacement
or spare parts be sure to provide the following information to the
manufacturerís Parts Department.
1.
2.
3.
4.
5.
6.
7.
Manual Number & Date of Publication
Manual Page Number
Page Title
Reference Number of Part Desired
Part Number
Part Description
Quantity of Part Desired
Providing this information will help ensure that the correct parts will be
delivered to you in an expedient manner without delay. Should additional
information be required for repair or replacement of certain components,
contact your Wrecker Manufacturer Authorized Representative.
The Manufacturer reserves the right, without notice or obligation, to improve
or modify their products, which may change the specifications, models and
feature availability.
VI-1
Section VI - PARTS (cont'd)
SUBFRAME ASSEMBLY
VI-2
Section VI - PARTS (cont'd)
SUBFRAME ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
------27
28
29
30
31
32
33
-----
6
8
12.
REF.
REF.
2
8
10
2
4
2
4
4
4
16
4
4
8
8
4
8
2
2
2
2
-4
4
2
4
2
4
1
2
2
1
1
1
-2
2
2
2
0300113
0302540
0302541
0302616
0303091
0303140
0400066
0400128
0400130
0400139
0400181
0400276
0400281
0400294
0400392
0400408
0400430
0400452
0400506
0400508
0400510
0705500
0707341
0707377
0707394
0707199
0301551
0301553
0302474
0400044
0400563
0702604
0802211
0802221
0802240
0802243
0802244
0802863
0903136
0303086
0400211
0400408
0400492
DESCRIPTION
GREASE FITTING
CENTER BONDED MOUNT
SPECIAL WASHER
SPADE CYLINDER
BOOM LIFT CYLINDER
RAMP PAD
SCREW, 1/4"-20 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" FL HD SKT
SCREW, 3/8"-16 X 3-1/2" HEX HD CAP
SCREW, 3/8"-16 X 1-1/2" HEX SKT SET
SCREW, 1/2"-13 X 1-1/2" HEX HD CAP
SCREW, 5/8"-11 X 4-1/2" HEX HD CAP
SCREW, 3/4"-10 X 3-1/2" HEX HD CAP
SCREW, 3/4"-10 X 6-1/2" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
NUT, 1/2"-13 NYLOK HEX
NUT, 3/4"-10 NYLOK HEX
LOCKWASHER, 1/4" HELICAL
WASHER, 5/8" FLAT
LOCKWASHER, 5/8" HELICAL
WASHER, 3/4" FLAT
SHAFT, LOWER SPADE
PIN, LIFT CYLINDER
COVER, SPADE TUBE
SHAFT, UPPER SPADE
PIN, SPADE PAD
CABLE SLEEVE, 1/16"
CABLE ASSEMBLY, 1/16" X 17"
PIN, LYNCH
DRIVE SCREW, #10 X 1/2" RD HD
ROLL PIN, 3/16" X 1-3/4"
PROTECTIVE HOSE TUBE, 14"
FRONT BODY MTG TUBE
SPADE PAD
PIVOT PIN, LIFT CYLINDER
INNER SPADE, LEFT
INNDER SPADE, RIGHT
4024 SUBFRAME WELDMENT
SAFETY CHAIN ASSEMBLY (NOT SHOWN)
SAFETY CHAIN
SCREW, 1/2"-13 X 1-34" HEX HD CAP
NUT, 1/2"-13 NYLOK HEX
WASHER, 1/2" FLAT
VI-3
Section VI - PARTS (cont'd)
BODY ASSEMBLY
Section VI - PARTS (cont'd)
BODY ASSEMBLY
VI-4
Section VI - PARTS (cont'd)
BODY ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
2
4
4
8
1
1
1
8
8
6
8
6
8
40
2
1
1
2
2
1
1
1
1
0301223
0301912
0902571
0302572
0302612
0302613
0303061
0400066
0400122
0400369
0400392
0400451
0400452
0400566
0704047
0705090
0705091
0705092
0706609
0711289
0711290
0711292
0711344
DESCRIPTION
MUD FLAP
DOOR CHECK, 11"
GAS SPRING CYLINDER
"L" BRACKET
BODY SIDE, 120" C.A., LEFT
BODY SIDE, 120" C.A., RIGHT
BACKUP ALARM
SCREW, 1/4"-20 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
CLIP, 1/4" TINNERMAN
NUT, 3/8"-16 NYLOK HEX
WASHER, 1/4" FLAT
LOCKWASHER, 1/4" HELICAL
RIVET, 1/4"
RUBBER FENDER
MUDFLAP MTG ANGLE, LEFT
MUDFLAP MTG ANGLE, RIGHT
BAR, MUDFLAP
RETAINING STRIP, RUBBER FENDER
PANEL, SWITCH
PANEL, CONTROL
PANEL, CONTROL
PANEL, GAUGE
VI-5
REF.
NO.
NO.
REQ'D
PART
NUMBER
24
1
0901496
CENTURY NAMEPLATE KIT
------
-28
28
2
2
0902328
0400288
0400431
0707174
0711256
BODY MOUNTING KIT
SCREW, 3/4"-10 X 2-1/2" HEX HD CAP
NUT, 3/4"-10 NYLOK HEX
ANGLE, TAILGATE MOUNTING
MOUNTING PLATE
--------25
26
27
28
-2
4
12
6
4
18
12
2
1
1
1
124001727
0301706
0400126
0400177
0400181
0400392
0400408
0400492
0802254
0802256
0802257
0802260
LIGHT BAR, STANDARD
GASKET, LIGHT BAR
SCREW, 3/8"-16 X 1" HEX HD CAP
SCREW, 1/2"-13 X 1-1/4" HEX HD CAP
SCREW, 1/2"-13 X 1-1/2" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
NUT, 1/2"-13 NYLOCK HEX
WASHER, 1/2" FLAT
MOUNTING ANGLE
SUPPORT CHANNEL, LEFT
SUPPORT CHANNEL, RIGHT
TOP CHANNEL
DESCRIPTION
Section VI - PARTS (cont'd)
BOOM ASSEMBLY
VI-6
Section VI - PARTS (cont'd)
BOOM ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
6
2
2
2
2
4
4
REF.
2
2
4
4
4
18
2
4
2
1
4
24
4
4
16
4
2
8
4
4
0300113
0300626
0303050
0301895
0301923
0301959
0302378
0302614
0302619
0302628
0400066
0400121
0400122
0400132
0400133
0400150
0400176
0400220
0400248
0400392
0400408
0400451
0400480
0400482
0400491
0400492
0400506
0400508
DESCRIPTION
GREASE FITTING
SHEAVE, 8"
WIRE ROPE, 6 X 19 IPS, 9/16" X 175' 0
GREASE FITTING, STR 1/8"
SLIDE PAD, BOOM BOTTOM
SNAP RING, 1-1/2" INTERNAL
COMPRESSION SPRING
EXTEND CYLINDER
BUSHING, 2-1/4" OD X 2" ID X 1-1/2"
SLIDE PAD, INNER BOOM
SCREW, 1/4"-20 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/2" HEX HD CAP
SCREW, 3/8"-16 X 3" HEX HD CAP
SCREW, 3/8"-16 X 2-1/2" HEX HD CAP
SCREW, 1/2"-13 X 1" HEX HD CAP
SCREW, 1/2"-13 X 5-1/2" HEX HD CAP
SCREW, 5/8"-11 X 1" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
NUT, 1/2"-13 NYLOK HEX
WASHER, 1/4" FLAT
WASHER, 3/8" FLAT
LOCKWASHER, 3/8" HELICAL
LOCKWASHER, 1/2" HELICAL
WASHER, 1/2" FLAT
WASHER, 5/8" FLAT
LOCKWASHER, 5/8" HELICAL
VI-7
REF.
NO.
NO.
REQ'D
PART
NUMBER
29
30
4
6
31
2
4
2
2
1
1
1
2
2
1
1
2
2
1
1
4
1
2
2
2
1
1
1
1
0400543
0400554
1
0700778
0700801
0700888
0703442
0707343
0707344
0707342
0709361
0709362
0710143
0708645
0711390
0800286
0800509
0800510
0802218
0802246
0802935
0802775
0802774
0802864
0803219
0802931
0803220
32
33
34
35
36
37
38
39
40
41
42
-43
44
45
46
47
48
49
50
51
52
53
--
DESCRIPTION
COTTER PIN, 1/8" X 3/4"
ROLL PIN, 3/8" X 1"
0400581 PIPE U-BOLT, 3/8"-18 X 3"
TOP SPACER, OUTER BOOM
CABLE GUIDE, BOTTOM
SHAFT, SHEAVE
SKID, FAIRLEAD ASSEMBLY
EXTEND CYLINDER PIN, BASE
EXTEND CYLINDER PIN, ROD
PIVOT PIN, BOOM
PIVOT ROD
SPRING CHANNEL
PIN, TILT CYLINDER BASE END
PLATE, FLAPPER (4024T)
PLATE, FLAPPER (4024T3)
CABLE GUIDE
SWIVEL WELDMENT, LEFT
SWIVEL WELDMENT, RIGHT
SPRING PIN
CYLINDER SUPPORT
PIN, TOWER PIVOT
TENSIONER, MOUNTING BRACKET
TENSIONER, BRACKET
OUTER BOOM WELDMENT (4024T)
OUTER BOOM WELDMENT (4024T2)
OUTER BOOM WELDMENT (4024T)
OUTER BOOM WELDMENT (4024T2)
Section VI - PARTS (cont'd)
UNDERLIFT & TOWER ASSEMBLY
VI-8
Section VI - PARTS (cont'd)
UNDERLIFT & TOWER ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
2
REF.
REF.
1
1
1
1
4
4
3
7
1
3
4
1
4
1
1
1
1
0300113
0301895
0301765
0302791
0304246
0400121
0400122
0400167
0400176
0400392
0400482
0400491
0400548
0710140
0710143
0710144
0802220
0802237
0802865
0802935
GREASE FITTING
GREASE FITTING, 1/8" STR
FOLD CYLINDER
TILT CYLINDER
PIN, FOLD CYLINDER CLEVIS
SCREW, 3/8"-16 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 3-3/4" HEX HD CAP
SCREW, 1/2"-13 X 1" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
LOCKWASHER, 3/8" HELICAL
LOCKWASHER, 1/2" HELICAL
COTTER PIN, 3/8" X 2"
BUSHING, TILT CYLINDER
PIN, TILT CYLINDER BASE END
PIN, TILT CYLINDER ROD END
PIN WELDMENT, FOLD CYLINDER
PIVOT PIN, UNDERLIFT
TOWER WELDMENT 4024
WELDMENT, TOWER PIVOT PIN
-21
22
23
24
-2
2
2
2
0901716
0301691
0302273
0400205
0400408
STOW KIT, WINCH CABLE
MASTER LINK, OBLONG
SPRING, WINCH CABLE TIE-BACK
SCREW, 1/2"-13 X 3" HEX HD CAP
NUT, 1/2"-13 NYLOK HEX
-25
26
27
-6
7
2
0903059
0300113
0302561
0302619
HORIZONTAL BOOM ASSEMBLY
GREASE FITTING, 1/8" STR
SLIDE PAD
SPRING BUSHING
VI-9
REF.
NO.
NO.
REQ'D
PART
NUMBER
-28
29
30
31
32
33
34
35
36
37
38
39
40
-4
8
8
5
2
9
5
1
1
1
2
1
1
0903752
0303331
0400107
0400151
0400228
0400382
0400481
0707034
0707271
0707452
0803231
0803232
HD86
HD89
HORIZONTAL BOOM ASSEMBLY (con't)
EXTEND CYLINDER
SCREW, 5/16"-18 X 2-1/2" HEX HD CAP
SCREW, 3/8"-24 X 5/8" BUTTON HD SKT
SCREW, 3/8"-24 X 5/8" HEX HD CAP
NUT, 5/16"-18 NYLOK HEX
LOCKWASHER, 3/8" EXTERNAL TOOTH
STOP PLATE
EXTEND CYLINDER PIN, BASE END
SPACER PAD
OUTER BOOM WELDMENT
2ND STAGE BOOM WELDMENT
EXTEND CYLINDER PIN WELDMENT
RETAINING RING
-41
42
43
44
45
46
47
48
49
50
51
-1
1
1
2
2
2
2
1
1
1
1
0903175
0301197
0301398
0303087
0303105
0303106
0400354
0400508
0710054
0710055
0710195
0802919
CROSSBAR ASSEMBLY
COMPRESSION SPRING, CROSS BAR
DETENT BALL, 1-3/16"
"O" RING, PIVOT PIN
THRUST WASHER, 1/8"
THRUST WASHER, 1/16"
SCREW, 5/8"-11 X 4-1/2" SKT HD CAP
LOCKWASHER, 5/8" HELICAL
PIVOT PIN, TOP HALF
PIVOT PIN, BOTTOM HALF
SPACER, DETENT SPRING
CROSSBAR WELDMENT
-52
53
-1
8
0903751
0302625
0803320
INNER BOOM ASSEMBLY
BUSHING, PIVOT PIN
3RD STAGE BOOM WELDMENT
DESCRIPTION
Section VI - PARTS (cont'd)
UNDERLIFT HYDRAULICS
VI-10
Section VI - PARTS (cont'd)
UNDERLIFT HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
7
1
1
1
4
2
2
3
1
1
1
1
2
1
1
2
12
4
12
4
2
2
2
REF.
1
2
1
1
6
1
2
4
2
2
2
0300044
0300142
0300206
0301424
0301470
0301473
0301485
0301522
0301730
0301731
0301765
0301837
0301880
0302035
0302036
0302509
0302514
0302548
0302549
0302551
0302581
0302582
0302596
REF.
0302791
0302805
0302815
0303017
0303108
0303331
0400064
0400118
0400366
0400451
0400452
DESCRIPTION
CONNECTOR, 6MJ-8MB
ELBOW, 6MJ-4MP90
BRANCH TEE, 6MJ-6MJ-4MP
CONNECTOR, 6MJ-4MP
ELBOW, 6MJ-8MP90
HOSE ASSEMBLY, 18"
HOSE ASSEMBLY, 81"
CONNECTOR, 6MJ-6MB
DOUBLE HOLDING VALVE
HOLDING VALVE
FOLD CYLINDER
IN-LINE ORIFICE
HOSE ASSEMBLY, 107"
HOSE ASSEMBLY, 18"
HOSE ASSEMBLY, 26"
ELBOW, 6MJ-8MP90
ADAPTER, 8MJ-6MJ
CLAMPING UNIT
SPLIT BUSHING, 1/2"
STACKING NUT, SKT HD
HOSE ASSEMBLY, 36"
HOSE ASSEMBLY, 36"
HOSE ASSEMBLY, 34"
CONTROL VALVE
TILT CYLINDER
HOSE ASSEMBLY, 10"
HOSE ASSEMBLY, 32"
CONNECTOR, 8MB-6FB
TUBE ASSEMBLY
EXTEND CYLINDER
SCREW, 1/4"-20 X 2" HEX HD CAP SLOTTED
SCREW, 5/16-18 X 3/4 HEX HD CAP
NUT, 1/4"-20 HEX
WASHER, 1/4" FLAT
LOCKWASHER, 1/4" HELICAL
VI-11
Section VI - PARTS (cont'd)
BOOM ELEVATION HYDRAULICS
VI-12
Section VI - PARTS (cont'd)
BOOM ELEVATION HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
9
8
9
10
16
11
12
13
14
15
16
17
18
16
20
21
22
23
24
REF.
2
4
2
2
2
4
2
4
2
1
2
2
4
2
2
1
1
2
1
4
4
4
4
2
REF
0300044
0300113
0300147
0300206
0300710
0301388
0301425
0301470
0301731
0302035
0302051
0302568
0302569
0302575
0302581
0302582
0302604
0302632
0303091
0400064
0400366
0400451
0400452
0703001
DESCRIPTION
CONTROL VALVE
CONNECTOR, 6MJ-8MB
GREASE FITTING
ELBOW, STREET 4MP-4FP90
BRANCH TEE, 6MJ-6MJ-4MP
CLAMP, CHECK VALVE RETAINING, 6-1/2"
ELBOW, 8MJ-8MB90
CONNECTOR, 6MJ-6MB
ELBOW, 6MJ-8MB90
HOLDING VALVE
HOSE ASSEMBLY, 18"
ELBOW 8MJ-6MP90
TUBING, HYDRAULIC
WIRE TIE, 29-3/4"
BULKHEAD RUN TEE W/NUT
HOSE ASSEMBLY, 36"
HOSE ASSEMBLY, 36"
HOSE ASSEMBLY, 44"
HOSE ASSEMBLY, 40"
CYLINDER BOOM LIFT
SCREW, 1/4"-20 X 2-1/4" RD HD SLOTTED
NUT, 1/4"-20 HEX
WASHER, 1/4" FLAT
LOCKWASHER, 1/4" HELICAL
BRACKET, CHECK VALVE MOUNTING
VI-13
Section VI - PARTS (cont'd)
BOOM EXTENSION HYDRAULICS
VI-14
Section VI - PARTS (cont'd)
BOOM EXTENSION HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
REF.
2
1
1
2
1
1
1
1
5
1
1
1
1
2
2
2
REF
0300044
0300209
0301425
0301620
0301696
0301731
0301782
0302000
0302062
0302581
0302605
0302614
0302635
0400122
0400392
0400480
DESCRIPTION
CONTROL VALVE
CONNECTOR, 6MJ-8MB
ELBOW, 6MJ-6MP90
CONNECTOR, 6MJ-6MB
ELBOW, 6MJ-6MB90
ELBOW, 6MJ-6FJX90
HOLDING VALVE
MALE RUN TEE, 6MJ-4MP-6MJ
HOSE ASSEMBLY, 24"
WIRE TIE, 21" (NOT SHOWN)
HOSE ASSEMBLY, 36"
HOSE ASSEMBLY, 44"
EXTEND CYLINDER
HOSE ASSEMBLY, 131"
SCREW, 3/8"-16 X 1-1/4" HAX HD CAP
NUT, 3/8"-16 NYLOCK HEX
WASHER, 3/8" FLAT
VI-15
Section VI - PARTS (cont'd)
PUMP, VALVE & FILTER HYDRAULICS
Section VI - PARTS (cont'd)
PUMP, VALVE & FILTER HYDRAULICS
VI-16
Section VI - PARTS (cont'd)
PUMP, VALVE & FILTER HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
2
1
2
2
2
6
6
0301485
0301507
0302205
0302577
0303435
0400021
0400351
HOSE ASSEMBLY, 81"
PUMP, OPPOSITE ENGINE
GAUGE, FLUSH MOUNT 6000 PSI
CONNECTOR, 6MJ-4FP
HOSE ASSEMBLY 58"
SCREW, #8-32 X 1/2" RD HD PHIL MACH
HEX NUT, & STAR WASHER, #8-32
29
30
31
32
33
34
35
10
4
6
2
1
2
1
0400392
0400480
0704045
0711249
0711250
0711251
0711561
NUT, 3/8"-16 NYLOK HEX
WASHER, 3/8" FLAT
SPACER, CONTROL VALVE
PLATE, CONTROL BULKHEAD (L.&R.S.C.)
PLATE, CONTROL BULKHEAD (L.&R.S.C.)
PLATE, CONTROL BULKHEAD (L.&R.S.C.)
PLATE VALVE MOUNTING
-8
9
10
11
12
13
14
15
16
17
18
19
20
21
-2
2
2
20 FT.
2
2
2
1
2
1
1
6
2
2
0903307
0300364
0300660
0300666
0300671
0300891
0301547
0302088
0302242
0302983
0303032
0303033
0303290
0400188
0400408
PUMP KIT
CLAMP HOSE, 1" - 2-1/4"
HOSE ASSEMBLY, 120"
BARB, 24C4-24MP
SUCTION HOSE, 1-1/2"
PIPE NIPPLE, 1-1/2" X 3"
ELBOW, 8MJ-12MB90
BALL VALVE, BRONZE
FLANGE FITTING, 24FL-24 HOSE 90
STREET ELBOW, 45∞ 1-1/2"
ELBOW, 24MJ-20MB90
HOSE BARB, 24C4-24FJX
CLAMP, 2-1/2" INSULATED
SCREW, 1/2"-13 X 2 HEX HD CAP
NUT, 1/2"-13 NYLOK HEX
0903535
REF.
0300052
0301995
0302052
REF.
0400135
0400157
VALVE PAN ASSEMBLY
CONTROL VALVE
ELBOW, 8MJ-10MB90
STRAIGHT ADAPTER, 8FJ-6MJ
RUN TEE, 8MJ-8FJX-8MJ
CONTROL VALVE
SCREW, 3/8"-16 X 4-1/2" HEX HD CAP
SCREW, 3/8"-16 X 1-3/4" HEX HD CAP
-36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
-2
1
2
2
4
4
1
1
6
12
4
6
4
12
1
1
1
0902353
0300136
0300446
0300615
0301545
0302227
0302228
0302570
0305006
0400036
0400122
0400146
0400357
0400392
0400482
0705910
0706114
0803163
TANK KIT
RETURN LINE FILTER ASSEMBLY
PIPE PLUG, 3/4" NPT MALE
ELL, 12MJ-12MP90
ELBOW, 12MJ-12MP90
CENTER BONDED MOUNT
SPECIAL WASHER
SIGHT GAUGE
FILLER CAP
SCREW, #10-32 X 1" RD HD MACH
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 2-1/4" HEX HD CAP
NUT, #10-32 NYLOK HEX
NUT, 3/8"-16 NYLOK HEX
LOCKWASHER, 3/8"HELICAL
COVER PLATE
GASKET, CLEAN OUT & FILLER COVER
RESERVOIR WELDMENT
-22
23
24
25
26
27
28
-REF.
2
2
2
REF.
6
4
-53
54
55
56
-4
4
1
4
0903696
0400121
0400392
0711322
0711575
COVER KIT
SCREW, 3/8"-16 X 3/4" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
COVER, VALVE
SUPPORT, COVER
DESCRIPTION
VI-17
DESCRIPTION
Section VI - PARTS (cont'd)
WORM DRIVE WINCH
HYDRAULICS & AIR FREE SPOOL
VI-18
Section VI - PARTS (cont'd)
WORM DRIVE WINCH
HYDRAULICS & AIR FREE SPOOL
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
REF.
2
2
2
4
2
18 FT.
2
7 FT.
4
4
2
1
2
4
1
REF.
2
2
1
1
2
2
4
8
2
0300011
0300324
0300691
0300897
0301376
0301574
0301577
0302055
0302431
0302546
0302550
0302551
0302607
0302677
0302678
0302744
0302782
0302827
0302828
0303049
0303048
0303131
0303391
0400034
0400059
0400118
DESCRIPTION
CONTROL VALVE
SOLENOID VALVE, AIR CONTROL
HYDRAULIC MOTOR
RUBBER GROMMET
CONNECTOR, 8MJ-10MB
ELBOW, 4TB-4MP90
AIR HOSE, 1/4" O.D.
AIR CYLINDER
CONVOLUTED LOOM, 3/8"
CLAMPING UNIT
SPLIT BUSHING, 3/4"
STACKING NUT, SKT HD
TEE UNION, 4TB-4TB-4TB
BREATHER VENT, 1/8" MP
ELBOW, 4TB-2MP90
AIR FREE SPOOL HARNESS
CONTROL VALVE
CONNECTOR, 10MJ-10MB
CONNECTOR, 10MJ-10MBL
WINCH, H-700, RIGHT
WINCH, H-700 LEFT
HOSE ASSEMBLY, 80"
HOSE ASSEMBLY, 96"
SCREW, #10-32 X 1/2" RD HD PHIL
SCREW, 1/4"-20 X 5/8" HEX HD
SCREW, 5/16"-18 X 3/4" HEX HD CAP
VI-19
REF.
NO.
NO.
REQ'D
PART
NUMBER
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
2
4
2
4
16
8
4
8
8
2
8
8
8
16
16
2
4
2
2
2
2
2
1
1
2
0400121
0400122
0400132
0400238
0400252
0400260
0400356
0400367
0400392
0400412
0400421
0400480
0400491
0400504
0400508
0400510
0400520
0400530
0400543
0702382
0706859
0706860
0709313
0709314
0800772
DESCRIPTION
SCREW, 3/8"-16 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/2" HEX HD CAP
SCREW, 1/2"-13 X 1-1/2" HEX HD CAP
SCREW, 5/8"-11 X 1-1/2" HEX HD CAP
SCREW, 5/8"-11 X 2" HEX HD CAP
NUT, #10-32 HEX
NUT, 1/4"-20 HEX NYLOK
NUT, 3/8"-16 HEX NYLOK
NUT, 1/2"-20 HEX JAM
NUT, 5/8"-11 HEX NYLOK
WASHER, 3/8" FLAT
LOCKWASHER, 1/2" HELICAL
WASHER, 5/8" SAE
LOCKWASHER, 5/8" HELICAL
WASHER, 3/4" FLAT
LOCKWASHER, #10 HELICAL
CLEVIS PIN, 5/16" X 1-1/4"
COTTER PIN, 1/8" X 3/4"
MOUNTING ANGLE
CHANNEL, CYLINDER MOUNTING
CHANNEL, CYLINDER COVER
WINCH MOUNTING ANGLE, FRONT
WINCH MOUNTING ANGLE, REAR
ADJUSTMENT YOKE
Section VI - PARTS (cont'd)
PLANETARY WINCH
HYDRAULICS & AIR FREE SPOOL
VI-20
Section VI - PARTS (cont'd)
PLANETARY WINCH
HYDRAULICS & AIR FREE SPOOL
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
4
2
18 FT.
2
7 FT.
4
4
2
1
2
4
2
2
1
1
1
1
2
2
16
16
2
2
2
2
0300041
0300324
0301577
0301207
0302431
0302546
0302550
0302551
0302607
0302677
0302678
0302827
0302828
0303093
0303094
0303374
0303375
0302950
0400118
0400264
0400421
0711395
0711396
0711397
0711398
DESCRIPTION
CONNECTOR, 8MJ-8MB
SOLENOID VALVE, AIR CONTROL
AIR HOSE, 1/4" O.D.
HOSE ASSEMBLY, 72"
CONVOLUTED LOOM, 3/8"
CLAMPING UNIT
SPLIT BUSHING, 3/4"
STACKING NUT, SKT HD
TEE UNION, 4TB-4TB-4TB
BREATHER VENT, 1/8" MP
ELBOW, 4TB-2MP90
CONNECTOR, 10MJ-10MB
CONNECTOR, 10MJ-10MBL
CONTROL VALVE
CONTROL VALVE
WINCH, LEFT
WINCH, RIGHT
HOSE ASSEMBLY, 100"
SCREW, 5/16"-18 x 3/4" HEX HD CAP
SCREW, 5/8"-11 x 2-1/4" HEX HD CAP
NUT, 5/8"-11 HEX NYLOK
ANGLE - WINCH MOUNTING
ANGLE - WINCH MOUNTING
ANGLE - WINCH MOUNTING
ANGLE - WINCH MOUNTING
VI-21
Section VI - PARTS (cont'd)
LEFT CONTROL ASSEMBLY
VI-22
Section VI - PARTS (cont'd)
LEFT CONTROL ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
1
2
1
2
1
1
4
4
9
1
1
12
2
9
4
4
2
4
9
36
10
9
4
24
10
9
9
2
1
1
1
1
6
1
9
0300341
0300834
0300835
0300836
0300837
0302453
0302454
0302455
0302726
0302856
0302917
0303008
0400066
0400103
0400107
0400122
0400367
0400379
0400382
0400383
0400392
0400393
0400451
0400466
0400512
0400532
0400541
0711235
0711245
0711246
0711284
0711285
0801054
0803182
0803294
DESCRIPTION
CONTROL KNOB, W/L (UP/DOWN)
CONTROL KNOB, (IN/OUT)
CONTROL KNOB, BOOM (UP/DOWN)
CONTROL KNOB, JACK (UP/DOWN)
CONTROL KNOB, BOOM (IN/OUT)
CONTROL CABLE, 92"
CONTROL CABLE, 67"
CONTROL CABLE, 79"
GREASE FITTING, 1/4"-28 X 45∞
CONTROL KNOB, TILT (UP/DOWN)
CONTROL KNOB, W/L EXTEND (IN/OUT)
ADJUSTABLE CLEVIS
SCREW, 1/4"-20 X 3/4" HEX HD CAP
SCREW, 5/16"-18 X 1-1/4" HEX HD CAP
SCREW, 5/16"-18 X 2-1/2" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
NUT, 1/4"-20 HEX NYLOK
NUT, 5/16"-18 "J" TINNERMAN
NUT, 5/16"-18 HEX NYLOK
NUT, 5/16"-24 HEX
NUT, 3/8"-16 HEX NYLOK
NUT, 3/8"-16 HEX JAM
WASHER, 1/4" FLAT
WASHER, 5/16" INTERNAL TOOTH
WASHER, 3/4" FLAT (SPECIAL)
CLEVIS PIN, 5/16" X 1"
COTTER PIN, 1/16" X 3/4"
CLAMP, SHAFT CONTROL BOX
PLATE, SHAFT SUPPORT
PIN, CONTROL BOX
SUPPORT, CONTROL (LEFT)
SUPPORT, CONTROL (RIGHT)
CONTROL CABLE CONNECTOR
CONTROL FRAME WELDMENT
CONTROL HANDLE WELDMENT
VI-23
REMOTE CONTROL ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
-36
37
38
39
40
41
42
43
44
45
46
47
-48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
-66
67
-10 / 16
1
15 / 25
2/4
2/3
2
2
1
35 / 65
1/2
16 / 28
1
1
1
1/2
1
1
8 / 20
4/7
1
1
1
2/4
4/7
2/4
2/4
6 / 11
4/7
2/4
4/7
1
1
4/7
1
-0300166
0301574
0301577
0301610
0301618
0302048
0302340
0302431
0302434
0302677
0302678
0302844
0303479
0303226
0303235
0303250
0303251
0303322
0303335
0303363
0303364
0303365
0400025
0400057
0400078
0400351
0400367
0400401
0400451
0400527
0711277
0711836
0803181
HA0132
DESCRIPTION
REMOTE CONTROL ASSEMBLY
WIRE CONNECTOR, SPADE
ELBOW, 4TB-4MP90
AIR HOSE, 1/4" O.D. (FT.)
CONNECTOR, 4TB-4MP
BRASS PLUG, 4MP
CABLE SEALING GRIP
HEX PIPE BUSHING
CONVOLUTED LOOM, 3/8" X 8"
CABLE TIE, 4" 18 LB.
BREATHER VENT, 2MP
ELBOW, 4TB-2MP
AIR SOLENOID VALVE (8)
AIR SOLENOID VALVE (14)
CIRCUIT BREAKER, HI-AMP WATERPROOF
TERMINAL BLOCK
POWER PAL, 15 POSITION
POWER PAL, 8 POSITION
ELECTRICAL CABLE, 16/10 SO (FT.)
AIR CYLINDER
AIR FILTER/REGULATOR
AIR LUBRICATOR
MOUNTING BRACKET
SCREW, #8-32 X 3/4" RD HD SLOTTED
SCREW, 1/4"-20 X 1-1/4" HEX HD CAP
SCREW, 1/4"-20 X 2" HEX HD CAP
HEX NUT & STAR WASHER, #8-32
NUT, 1/4"-20 HEX NYLOK
NUT, 7/16"-20 HEX JAM
WASHER, 1/4" FLAT
CLEVIS PIN, 5/16" X 5/8" COTTERLESS
SUPPORT, SOLENOID VALVE (8)
SUPPORT, SOLENOID VALVE (14)
CLEVIS WELDMENT
GAUGE, 0-160 PSI
Section VI - PARTS (cont'd)
RIGHT CONTROL ASSEMBLY
VI-24
Section VI - PARTS (cont'd)
RIGHT CONTROL ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
2
1
2
1
3
3
6
6
6
4
4
4
10
18
4
6
18
4
7
6
6
2
1
1
1
1
6
0300834
0300835
0300836
0300837
0302453
0302455
0302726
0303008
0400103
0400107
0400122
0400379
0400382
0400383
0400392
0400393
0400466
0400480
0400512
0400532
0400541
0711235
0711247
0711284
0711285
0803183
0803294
DESCRIPTION
CONTROL KNOB, (IN/OUT)
CONTROL KNOB, BOOM (UP/DOWN)
CONTROL KNOB, JACK (UP/DOWN)
CONTROL KNOB, BOOM (IN/OUT)
CONTROL CABLE, 92"
CONTROL CABLE, 79"
GREASE FITTING, 1/4"-28 X 45∞
ADJUSTABLE CLEVIS
SCREW, 5/16"-18 X 1-1/4" HEX HD CAP
SCREW, 5/16"-18 X 2-1/2" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
NUT, 5/16"-18 "J" TINNERMAN
NUT, 5/16"-18 HEX NYLOK
NUT, 5/16"-24 HEX
NUT, 3/8"-16 HEX NYLOK
NUT, 3/8"-16 HEX JAM
WASHER, 5/16" INTERNAL TOOTH
WASHER, 3/8" FLAT
WASHER, 3/4" FLAT (SPECIAL)
CLEVIS PIN, 5/16" X 1"
COTTER PIN, 1/16" X 3/4"
CLAMP, SHAFT CONTROL BOX
PIN, CONTROL BOX
SUPPORT, CONTROL (LEFT)
SUPPORT, CONTROL (RIGHT)
CONTROL FRAME WELDMENT
CONTROL HANDLE WELDMENT
VI-25
Section VI - PARTS (cont'd)
REAR SPADE HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
REF.
2
4
2
4
2
REF.
2
2
REF.
0300044
0300689
0301522
0301819
0302616
REF.
0303017
0303175
DESCRIPTION
CONTROL VALVE
CONNECTOR, 6MJ-6MB
STREET ELBOW, STEEL, 8MJ-8FP90
CONNECTOR 6MJ-6MB
NIPPLE, BLACK PIPE, 1/2" X 4-1/2"
HYDRAULIC CYLINDER
CONTROL VALVE
CONNECTOR, 8MB-6FB
HOSE ASSEMBLY, 102"
VI-26
Section VI - PARTS (cont'd)
HYDRAULIC CYLINDERS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
2
1
0303091
14207
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
1
0302614
0304503
DESCRIPTION
BOOM ELEVATION CYLINDER (COMPLETE)
SEAL KIT, BOOM ELEVATION CYLINDER
DESCRIPTION
BOOM EXTENSION CYLINDER (COMPLETE)
SEAL KIT, BOOM EXTENSION CYLINDER
VI-27
Section VI - PARTS (cont'd)
HYDRAULIC CYLINDERS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
1
0302791
0304488
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
1
0303331
030xxx
DESCRIPTION
CYLINDER, UNDERLIFT TILT (COMPLETE)
SEAL KIT, UNDERLIFT TILT CYLINDER
DESCRIPTION
CYLINDER, UNDERLIFT EXTEN. (COMPLETE)
SEAL KIT, UNDERIFT EXTENSION CYLINDER
VI-28
Section VI - PARTS (cont'd)
HYDRAULIC CYLINDERS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
1
0301765
0304244
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
2
1
0302616
0304244
DESCRIPTION
CYLINDER, UNDERLIFT FOLD (COMPLETE)
SEAL KIT, UNDERLIFT FOLD CYLINDER
DESCRIPTION
CYLINDER, REAR SPADE (COMPLETE)
SEAL KIT, REAR SPADE CYLINDER
VI-29
Section VI - PARTS (cont'd)
GLAD HAND KIT
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
1
2
2
2
2
1
2
2
2
2
0301909
0301944
0301945
0301946
0301947
0301948
0400070
0400367
0400451
0703795
DESCRIPTION
RECEPTACLE BOOT
GLAD HAND COUPLING
GLAD HAND PLUG
BULKHEAD CONNECTOR
ADAPTER, 1/4" NPM X 3/8" SYN. HOSE
HD 7-WAY TRAILER CONNECTOR
SCREW, 1/4"-20 X 1" HEX HD CAP
NUT, 1/4"-20 HEX NYLOK
WASHER, 1/4" FLAT
AIR HOSE, 3/8" X 48" SYNFLEX
VI-30
Section VI - PARTS (cont'd)
LIFT ADAPTERS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
2
2
2
2
2
2
2
1
1
1
1
2
0200018
0200020
0200021
0200023
0400585
0711001
0800590
0802251
0802252
0803580
0803581
0902378
DESCRIPTION
FORK, SHORT (3" OPENING)
FORK, MEDIUM (3" OPENING)
FORK, MEDIUM (4-1/2" OPENING)
FORK, LONG (4-1/2" OPENING)
HAIR PIN COTTER, 1-1/4"
BOLT, MODIFIED 5/8"-11 X 5" WITH HOLE
TEE HANDLE, FORK ADAPTER
CHAIN HOOK ADAPTER, RT
CHAIN HOOK ADAPTER, LT
OFFSET FORK ADAPTER, LT
OFFSET FORK ADAPTER, RT
RETAINER PIN ASSEMBLY
VI-31
Section VI - PARTS (cont'd)
OUTER CROSSTUBE ASSEMBLY
VI-32
Section VI - PARTS (cont'd)
OUTER CROSSTUBE ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2
2
2
2
2
2
2
2
2
2
2
2
4
2
1
1
1
1
2
0300113
0300341
0301417
0301681
0301682
0400269
0400393
0400421
0400506
0400559
0400560
0706688
0800590
0800839
0802069
0802070
0802231
0802232
0802606
DESCRIPTION
GREASE FITTING
KNOB, "L" BAR LOCK CONTROL
SPRING, PLUNGER PIN
EXTENSION, TIRE RESTRAINT
TIRE RESTRAINT
BOLT, 5/8"-11 X 4-1/2" CARRIAGE
NUT, 3/8"-16 HEX JAM
NUT, 5/8"-11 HEX NYLOK
WASHER, 5/8" FLAT
PIN, 3/16" X 1" ROLL
PIN, 5/32" X 1" ROLL
PIN, PLUNGER
HANDLE, "T"
BRACKET, RESTRAINT ASSEMBLY PIVOT
HANDLE, L.H. PLUNGER PIN
HANDLE, R.H. PLUNGER PIN
CROSSBAR, LEFT OUTER
CROSSBAR, RIGHT OUTER
TIRE RESTRAINT, MEDIUM
VI-33
Section VI - PARTS (cont'd)
KING PIN ADAPTER
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
1
0803605
KING PIN ADAPTER WELDMENT
-2
3
4
5
6
-1
2
1
1
1
0902782
0400555
HD1259
VA0660
VA0661
VA0662
FIFTH WHEEL ADAPTER (COMPLETE)
ROLL PIN, 3/8" X 1-1/2"
PIN SNAPPER
FIFTH WHEEL PIVOT PLATE WELDMENT
PULL PIN WELDMENT
PIVOT PIN WELDMENT
-7
8
9
10
-1
4
4
1
124002211
0302198
0400176
0400491
0803604
11
2
0902378
DESCRIPTION
PINTLE HOOK KIT (COMPLETE)
PINTLE HOOK (NOT SHOWN)
SCREW, 1/2"-13 X 1" HEX HD CAP
LOCKWASHER, 1/2" HELICAL
5TH WHEEL, KING PIN ADAPTER & PINTLE
HOOK BRACKET
RETAINING PIN ASSEMBLY
VI-34
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
2
24
0302542
0302543
0400025
DESCRIPTION
LIGHT, STOP & TURN ( COMPLETE)
LIGHT, BACK-UP (COMPLETE)
SCREW, #8-32 x 3/4" RD HD SLOTTED
VI-35
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
1
2
3
0300442
0300507
0200511
REF.
NO.
PART
NUMBER
1
2
3
4
5
0301390
0304123
0304124
0304125
0304126
DESCRIPTION
3-LIGHT BAR ASSEMBLY (COMPLETE)
BULB, MARKER LIGHT
LENS, 3-LIGHT BAR
DESCRIPTION
LIGHT, TURN (COMPLETE)
BEZEL MOUNTING SCREW
CHROME BEZEL
LENS & BULB ASSEMBLY
GROMMET & PLUG KIT
VI-36
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
1
0302201
REF.
NO.
PART
NUMBER
1
0302544
DESCRIPTION
LIGHT, FLOOD (COMPLETE)
DESCRIPTION
LIGHT, DOME (COMPLETE)
VI-37
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
1
2
3
0301740
0301741
0301742
REF.
NO.
PART
NUMBER
1
2
3
0300076
0300273
0300512
DESCRIPTION
GROMMET & PLUG, MARKER LIGHT
SEALED MARKER LIGHT, RED
SEALED MARKER LIGHT, AMBER
DESCRIPTION
BRACKET, LICENSE PLATE
LICENSE PLATE ILLUMINATOR (COMPLETE)
BULB, LICENSE PLATE ILLUMINATOR
VI-38
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
PART
NUMBER
1
0302611
DESCRIPTION
LIGHT, AMBER MARKER (COMPLETE)
VI-39
NOTES
NOTES
CENTURY®
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive • Ooltewah, Tennessee 37363 • (423) 238-4171
www.millerind.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement